Single-door access controller Circuit diagram: When J1 jumps to Null,normal status is cutoff.

1. JP1 connection:
(Card/Password) NO and COM are connected when available card
is read. NC andCOM are disconnected when
available card is read.
When J1 jumps to Push, Push port will output low
User Instruction voltage level, electronic lock connects lines
connect the power supply, The end of PUSH
Install instruction: connects power supply PUSH.
Special attention: 2. Description for setup of J2:
Unpack cross screw that fixed on faceplate
1.Please follow the instructions strictly while When J2 jumps to Single ,the winding reader is
and bottom board, then take off bottom board
using it. useless,when J2 jumps to the Double,user can
and install it on the side wall of the entrance open the door at both sides via single-door access.
2.Please read this instruction carefully before you use
the system and follow the instructions strictly while with collocated plastic plug and bolt, pay Programming setup:
using it. attention to the upper and nether direction. Original management password is 12345 and
Warning: user’s password is 8888.
Function parameter: 1. please ensure to switch off power before 1. enter programming
Working voltage: DC12V Press <* >=>input management password=>press #
Unlock current: ≦1.5A connecting lines and switch on power Description for setup of jumpers:
2. function setup ( under programming)
Static current: ≦0.6A after all lines being connected well! And 1. Description for setup of jumpers J1:
(1) modify management password:
Card quantity: 800pieces/800pass word please be sure that power voltage is 12v When J1 jumps to Lock,the electronic lock
Press <0> =>input new management
Maximum card-sensing distance: 10cm-20cm and that anode & cathode are in place! connects the two lines ( Lock and No/Nc) of the
password=>press
RF card type: EM or EM compatible card access controller. Lock port will output high
<# >=>input new management password =>press
Size: 117mm x 117mm x 21mm voltage level.
<#>
－－１－－ －－２－－ －－３－－ －－４－－
Note: the password must be 1-10 digital numbers ③ Open with reading a valid card or input correct card has been read, then press <#>
(2) add user’s card password: Press <302> =>press # Every card have different passward, The default is Issue type Red light Green Buzzer
light
Press <1> =>read the card =>continually read the Note: original setup is 302 for reading valid card or the four-digit user serial number . Normal working Glitter
card =>press <#> input password to open the door. 3. open the door with password: circumstance
② the 1st card must input with code, or the (5) Setup for door-open time Input user’s password and press <#> Read valid card / On 2 short toots
correct
card is invalid. Press<4> => <XX> => press # Note: This door controller supports normal card password, unlock
③ if you want to add more cards Note: XX is within 01-99, the time is measured by model, password model and both valid card Open door and On 1 short toot
successively, there is no need to input the seconds and the original setup is 3 seconds. and password model. press button,
then unlock
card code again after the first one, but just (6) How to modify open-door password Initialization of the door controller: Wrong password On 3 short toots
directly read cards, then finally press # Press<5>=> input new password with 1--10 digital If users forget the changed administration Invalid card On 3 short toots
(3) 3 ways to delete user card numbers => press<#> => input the new password password, this method can be used for recovering. The Press valid On 1 short toot
button
① Delete all user cards: press< 2 >=> press< again => press <#>to save jumper switch RESET on the motherboard can be used Alert to prevent Glittering Continually
0000> => press <#> (7) EXIT for recovering the original setup. Switch off power and from dismantling long playing
② Delete the card which has been read: press Press <*> to save switch jumper to ON, then turn on the power. Switch tooting
Programming On Glitter 2 short toots
<2> => read card => press< #> Note: any setup in point 1 and 2 jumper to OFF after the buzzer beeps 3 times and status
③ Delete a lost card: press <2> => input the hereinbefore must be saved by pressing * then initialization is completed.
digits card code =>press # exit. Note: 1. Initialization only changes system password to
Note: It costs 3-5 seconds to delete all the cards. default management password--12345 and
The green light flickers during the process.
How to use:
1. open the door with a card: user password--8888, other data will not be Packing list:
(4) Setup for open-door mode Normally, the door will be opened with one card changed. Door controller 1 set
① Open with reading a valid card: Press <300> once. 2. Normally please don’t used initialization User instruction 1 piece
=> press<#> unless users forget the password. Plastic insert for fixing and screws 1 bag
② Open with reading a valid card and password:
2. open the door with a card and a password:
Input the right password within 10 seconds after a Attachment 1: Description of signal light
Press <301>=> press <#> and buzzer
－－５－－ －－６－－ －－７－－ －－８－－