MODULE 2: Assembly Programming and Instruction of 8051

Microcontroller Notes:18EE52 2020_2021 Microcontroller Notes:18EE52 2020_2021
MODULE 2: Assembly Programming and Instruction of 8051 2.1 Introduction to 8051 assembly programming
Structure  In the early days of the computer, programmers coded in machine language,
consisting of 0s and 1s : Tedious, slow and prone to error.
 Assembly languages, which provided mnemonics for the machine code instructions,
2.1 Introduction to 8051 assembly programming plus other features, were developed: An Assembly language program consist of a
series of lines of Assembly language instructions
2.2 Assembling and running an 8051 program  Assembly language is referred to as a low level language: It deals directly with the
internal structure of the CPU.
2.3 Data types and Assembler directives
2.1.1 Assembly language instruction includes
2.4 Arithmetic, logic instructions and programs
 A mnemonic (abbreviation easy to remember) ƒ the commands to the CPU, telling
2.5 Jump, loop and call instructions
it what those to do with those items
2.6 IO port programming  optionally followed by one or two operands ƒ the data items being manipulated
 A given Assembly language program is a series of statements, or lines:
1. Assembly language instructions ƒ
Objectives Tell the CPU what to do
2. Directives (or pseudo-instructions)
Give directions to the assembler
 To explain in detail the execution of 8051 Assembly language instructions and data General syntax for 8051 assembly language is as follows:
types
 To explain loop, conditional and unconditional jump and call, handling and LABEL: OPCODE OPERAND; COMMENT
manipulation of I/O instructions.  LABEL: (THIS IS NOT NECESSARY UNLESS THAT SPECIFIC LINE HAS TO
BE ADDRESSED). The label is a symbolic address for the instruction. When the
program is assembled, the label will be given specific address in which that
instruction is stored. Unless that specific line of instruction is needed by a branching
instruction in the program, it is not necessary to label that line. Eg: BACK, HERE
 OPCODE: Opcode is the symbolic representation of the operation. The assembler
converts the opcode to a unique binary code (machine language). Eg:MOV, ADD
 OPERAND: While opcode specifies what operation to perform, operand specifies
where to perform that action. The operand field generally contains the source and
destination of the data. In some cases only source or destination will be available
instead of both. The operand will be either address of the data, or data itself.
 COMMENT: Always comment will begin with ; or // symbol. To improve the
program quality, programmer may always use comments in the program.
Department of Electrical & Electronics Engineering, ATMECE, Mysuru Page 1 Department of Electrical & Electronics Engineering, ATMECE, Mysuru Page 2
2.2.1 The lst (list) file
2.2 Assembling and running an 8051 program 1. It lists all the opcodes and addresses as well as errors that the assembler detected.
2. The programmer uses the lst file to find the syntax errors or debug
The steps of Assembly language program is outlined as follows:
1. First we use an editor to type a program, many excellent editors or word processors
are available that can be used to create and/or edit the program 2.3 Data types and Assembler directives
 Notice that the editor must be able to produce an ASCII file
Assembler directives tell the assembler to do something other than creating the machine code
 For many assemblers, the file names follow the usual DOS conventions, but the
for an instruction. In assembly language programming, the assembler directives instruct the
source file has the extension “asm“ or “src”, depending on which assembly you
assembler to
are using.
2. The “asm” source file containing the program code created in step 1 is fed to an 8051 1. Process subsequent assembly language instructions
assembler ƒ The assembler converts the instructions into machine code. The
assembler will produce an object file and a list file .The extension for the object file 2. Define program constants
is “obj” while the extension for the list file is “lst”
3. Reserve space for variables
3. Assembler require a third step called linking ƒ
 The linker program takes one or more object code files and produce an absolute The following are the widely used 8051 assembler directives.
object file with the extension “abs” ƒ
1. ORG (origin): The ORG directive is used to indicate the starting address. It can be
 This abs file is used by 8051 trainers that have a monitor program
used only when the program counter needs to be changed. The number that comes
4. Next the “abs” file is fed into a program called “OH” (object to hex converter) which
after ORG can be either in hex or in decimal.
creates a file with extension “hex” that is ready to burn into ROM
Eg: ORG 0000H;
 This program comes with all 8051 assemblers
 ƒ Recent Windows-based assemblers combine step 2 through 4 into one step
2. EQU and SET : EQU and SET directives assign numerical value or register name to
the specified symbol name.
EQU is used to define a constant without storing information in the memory.
The symbol defined with EQU should not be redefined.
SET directive allows redefinition of symbols at a later stage.
3. DB (DEFINE BYTE): The DB directive is used to define an 8 bit data. DB directive

initializes memory with 8 bit values.
The numbers can be in decimal, binary, hex or in ASCII formats.
For decimal, the 'D' after the decimal number is optional, but for binary and
hexadecimal, 'B' and ‘H’ are required.
For ASCII, the number is written in quotation marks (‘LIKE This).
DATA1: : DB 40H ; hex
DATA2: DB 01011100B ; b i n a r y
DATA3: DB 48 ; decimal
DATA4: D B ' H E L L O ’ ; ASCII
4. END: The END directive signals the end of the assembly module. It indicates the end
of the program to the assembler. Any text in the assembly file that appears after the
END directive is ignored. If the END statement is missing, the assembler will
Fig: 2.1: Steps of Assembly language program generate an error message.
e. Move the contents of a memory location to Rn or Rn to a memory location using direct addressing
2.4 Arithmetic, logic instructions and programs i. MOV R3, 65H

ii. MOV 45H, R2
8051 Instructions The instructions of 8051 can be broadly classified under the following f. Move the contents of memory location to another memory location using direct and indirect
headings. addressing
1. Data transfer instructions i. MOV 47H, 65H

ii. MOV 45H, @R0
2. Arithmetic instructions
3. Logical instructions g. Move the contents of an external memory to A or A to an external memory

i. MOVX A,@R1
4. Branch instructions ii. MOVX @R0,A
5. Subroutine instructions iii. MOVX A,@DPTR
iv. MOVX@DPTR,A
6. Bit manipulation instructions
1. Data transfer instructions. h. Move the contents of program memory to A
In this group, the instructions perform data transfer operations of the following types. i. MOVC A, @A+PC
a. Move the contents of a register Rn to A ii. MOVC A, @A+DPTR
i. MOV A,R2
ii. MOV A,R7
b. Move the contents of a register A to Rn
i. MOV R4,A
ii. MOV R1,A
c. Move an immediate 8 bit data to register A or to Rn or to a memory location (direct or
indirect)
i. MOV A, #45H
ii. MOV R6, #51H
iii. MOV 30H, #44H
iv. MOV @R0, #0E8H
v. MOV DPTR, #0F5A2H
Fig:2.2: Addressing using MOV,MOVX,MOVC
vi. MOV DPTR, #5467H
d. Move the contents of a memory location to A or A to a memory location using direct and indirect
addressing
i. MOV A, 65H
ii. MOV A, @R0
iii. MOV 45H, A
iv. MOV @R1, A
2.4.1 Arithmetic instructions
The 8051 can perform addition, subtraction. Multiplication and division operations on 8 bit numbers:
a) Addition:
In this group, we have instructions to
i. Add the contents of A with immediate data with or without carry.
i. ADD A, #45H
ii. ADDC A, #OB4H
ii. Add the contents of A with register Rn with or without carry.
i. ADD A, R5
ii. ADDC A, R2
iii. Add the contents of A with contents of memory with or without carry using direct and indirect
addressing
i. ADD A, 51H
ii. ADDC A, 75H
iii. ADD A, @R1
iv. ADDC A, @R0
Example: The Accumulator holds 0C3H (11000011B) and register 0 holds 0AAH (10101010B) with
the carry flag set. The following instruction, ADDC A,R0 leaves 6EH (01101110B) in the
Accumulator with AC cleared and both the Carry flag and OV set to 1.
CY AC and OV flags will be affected by this operation.
b) Subtraction:
SUBB A, <src-byte>
Function: Subtract with borrow
Description: SUBB subtracts the indicated variable and the carry flag together from the Accumulator,
leaving the result in the Accumulator. SUBB sets the carry (borrow) flag if a borrow is needed for bit
7 and clears C otherwise. (If C was set before executing a SUBB instruction, this indicates that a
borrow was needed for the previous step in a multiple-precision subtraction, so the carry is subtracted
from the Accumulator along with the source operand.) AC is set if a borrow is needed for bit 3 and
cleared otherwise. OV is set if a borrow is needed into bit 6, but not into bit 7, or into bit 7, but not bit
6
Example: The Accumulator holds 0C9H (11001001B), register 2 holds 54H (01010100B), and the
carry flag is set. The instruction, SUBB A,R2 will leave the value 74H (01110100B) in the
accumulator, with the carry flag and AC cleared but OV set.
In this group, we have instructions to
i. Subtract the contents of A with immediate data with or without carry.
i. SUBB A, #45H
ii. SUBB A, #OB4H
ii. Subtract the contents of A with register Rn with or without carry.
i. SUBB A, R5
ii. SUBB A, R2
iii. Subtract the contents of A with contents of memory with or without carry using direct and indirect
addressing
i. SUBB A, 51H
ii. SUBB A, 75H
iii. SUBB A, @R1
iv. SUBB A, @R0
CY AC and OV flags will be affected by this operation.
c) Multiplication
 MUL AB: This instruction multiplies two 8 bit unsigned numbers which are stored in A and
B register.
 After multiplication the lower byte of the result will be stored in accumulator and higher
byte of result will be stored in B register.
Eg. MOV A,#45H ; [A]=45H
MOV B,#0F5H ; [B]=F5H
MUL AB ; [A] x [B] = 45 x F5 = 4209 ;[A]=09H, [B]=42H
d) Division: Increment: Increments the operand by one.

 DIV AB. This instruction divides the 8 bit unsigned number which is stored in A by the 8 bit 1. INC increments the value of source by 1.
unsigned number which is stored in B register. 2. If the initial value of register is FFh, incrementing the value will cause it to reset to 0.
 After division the result will be stored in accumulator and remainder will be stored in B 3. The Carry Flag is not set when the value "rolls over" from 255 to 0. In the case of "INC
register. DPTR", the value two-byte unsigned integer value of DPTR is incremented. If the initial
Eg. MOV A,#45H ; [A]=0E8H value of DPTR is FFFFh, incrementing the value will cause it to reset to 0.
MOV B,#0F5H ; [B]=1BH Eg: INC A
DIV AB ; [A] / [B] = E8 /1B = 08 H with remainder 10H ;[A] = 08H, [B]=10H INC Rn
INC DIRECT
Function: Divide INC @Ri
Description: DIV AB divides the unsigned eight-bit integer in the Accumulator by the unsigned INC DPTR
eight-bit integer in register B. The Accumulator receives the integer part of the quotient; register B
receives the integer remainder. The carry and OV flags are cleared. Decrement: decrements the operand by one
Exception: if B had originally contained 00H, the values returned in the Accumulator and B register DEC decrements the value of source by 1. If the initial value of is 0, decrementing the value will
are undefined and the overflow flag are set. The carry flag is cleared in any case. cause it to reset to FFh. The Carry Flag is not set when the value "rolls over" from 0 to FFh.
Example: The Accumulator contains 251 (0FBH or 11111011B) and B contains 18 (12H or Eg: DEC A
00010010B). The following instruction, DIV AB leaves 13 in the Accumulator (0DH or 00001101B) DEC Rn
and the value 17 (11H or 00010001B) in B, since 251 = (13 x 18) + 17. Carry and OV are both DEC DIRECT
cleared. DEC @Ri
e) DA A (Decimal Adjust After Addition) 2.4.2 Logical Instructions

When two BCD numbers are added, the answer is a non-BCD number. To get the result in BCD, we
use DA A instruction after the addition. a) Logical AND
DA A works as follows. ANL destination, source: ANL does a bitwise "AND" operation between source and destination,
 If lower nibble is greater than 9 or auxiliary carry is 1, 6 is added to lower nibble leaving the resulting value in destination. The value in source is not affected. "AND" instruction
 If upper nibble is greater than 9 or carry is 1, 6 is added to upper nibble. logically AND the bits of source and destination
ANL A,#DATA
Eg 1: MOV A,#23H ANL A, Rn
MOV R1,#55H ANL A,DIRECT
ADD A,R1 // [A]=78 ANL A,@Ri
DA A // [A]=78 no changes in the accumulator after da a ANL DIRECT,A

ANL DIRECT, #DATA
Eg 2: MOV A,#53H Example: If the Accumulator holds 0C3H (1100001lB), and register 0 holds 55H (01010101B), then
MOV R1,#58H the following instruction, ANL A,R0 leaves 41H (01000001B) in the Accumulator
ADD A,R1 // [A]=ABh

DA A // [A]=11, C=1 , ANSWER IS 111. Accumulator data is changed after DA A
b) Logical OR SWAP A
ORL destination, source: ORL does a bitwise "OR" operation between source and destination, Swap the upper nibble and lower nibble of A
leaving the resulting value in destination. The value in source is not affected. " OR " instruction Function: Swap nibbles within the Accumulator
logically OR the bits of source and destination. Description: SWAP A interchanges the low- and high-order nibbles (four-bit fields) of the
ORL A,#DATA Accumulator (bits 3 through 0 and bits 7 through 4). The operation can also be thought of as a 4- bit
ORL A, Rn rotate instruction. No flags are affected. Example: The Accumulator holds the value 0C5H
ORL A,DIRECT (11000101B). The instruction, SWAP A leaves the Accumulator holding the value 5CH (01011100B)
ORL A,@Ri
ORL DIRECT,A XCH A,<byte>
ORL DIRECT, #DATA Function: Exchange Accumulator with byte variable Description: XCH loads the Accumulator with
Example: If the Accumulator holds 0C3H (11000011B) and R0 holds 55H (01010101B) then the the contents of the indicated variable, at the same time writing the original Accumulator contents to
following instruction, ORL A,R0 leaves the Accumulator holding the value 0D7H (1101011lB). the indicated variable. The source/destination operand can use register, direct, or register-indirect
c) Logical Ex-OR addressing.
XRL destination, source: XRL does a bitwise "EX-OR" operation between source and destination, Example: R0 contains the address 20H. The Accumulator holds the value 3FH (0011111lB). Internal
leaving the resulting value in destination. The value in source is not affected. " XRL " instruction RAM location 20H holds the value 75H (01110101B). The following instruction, XCH A,@R0 leaves
logically EX-OR the bits of source and destination. RAM location 20H holding the values 3FH (00111111B) and 75H (01110101B) in the accumulator.
XRL A,#DATA CPL A

XRL A,Rn Function: Complement Accumulator
XRL A,DIRECT Description: CPLA logically complements each bit of the Accumulator (one’s complement). Bits
XRL A,@Ri which previously contained a 1 are changed to a 0 and vice-versa. No flags are affected.
XRL DIRECT,A Example: The Accumulator contains 5CH (01011100B). The following instruction, CPL A leaves
XRL DIRECT, #DATA the Accumulator set to 0A3H (10100011B).
Example: If the Accumulator holds 0C3H (1100001lB) and register 0 holds 0AAH (10101010B) then
the instruction, XRL A,R0 leaves the Accumulator holding the value 69H (01101001B). CPL bit
Function: Complement bit
d)Logical NOT Description: CPL bit complements the bit variable specified. A bit that had been a 1 is changed to 0
CPL complements operand, leaving the result in operand. If operand is a single bit then the state of and vice-versa. No other flags are affected. CLR can operate on the carry or any directly addressable
the bit will be reversed. If operand is the Accumulator then all the bits in the Accumulator will be bit.
reversed. Example: Port 1 has previously been written with 5BH (01011101B). The following instruction
CPL A sequence, CPL P1.1CPL P1.2 leaves the port set to 5BH (01011011B).
CPL C
CPL bit address
Rotate Instructions
RR A 2.5 Branch (JUMP) Instructions
This instruction is rotate right the accumulator. Its operation is illustrated below. Each bit is shifted
one location to the right, with bit 0 going to bit 7. Jump and Call Program Range There are 3 types of jump instructions.
They are:-
1. Relative Jump
2. Short Absolute Jump
3. Long Absolute Jump
RL A
1. Relative Jump
Rotate left the accumulator. Each bit is shifted one location to the left, with bit 7 going to bit 0
Jump that replaces the PC (program counter) content with a new address that is greater than (the
address following the jump instruction by 127 or less) or less than (the address following the jump by
128 or less) is called a relative jump. Schematically, the relative jump can be shown as follows: -
Example: The Accumulator holds the value 0C5H (11000101B). The following instruction,
RL A leaves the Accumulator holding the value 8BH (10001011B) with the carry unaffected.
RRC A
Rotate right through the carry. Each bit is shifted one location to the right, with bit 0 going into the
carry bit in the PSW, while the carry was at goes into bit 7
Example: The Accumulator holds the value 0C5H (11000101B), the carry is zero. The following Fig 2.3: Relative Jump Range
instruction, RRC A leaves the Accumulator holding the value 62 (01100010B) with the carry set.
RLC A The advantages of the relative jump are as follows:-
Rotate left through the carry. Each bit is shifted one location to the left, with bit 7 going into the carry 1. Only 1 byte of jump address needs to be specified in the 2's complement form, ie. For jumping
bit in the PSW, while the carry goes into bit 0. ahead, the range is 0 to 127 and for jumping back, the range is -1 to -128.
2. Specifying only one byte reduces the size of the instruction and speeds up program execution.
3. The program with relative jumps can be relocated without reassembling to generate absolute jump
addresses.
Example: The Accumulator holds the value 0C5H(11000101B), and the carry is zero. The following
instruction, RLC A leaves the Accumulator holding the value 8BH (10001010B) with the carry set. Disadvantages of the absolute jump: -
1. Short jump range (-128 to 127 from the instruction following the jump instruction)
Instructions that use Relative Jump
SJMP ; this is unconditional jump
Operation: SJMP Function: Short Jump Syntax: SJMP reladdr 3. Long Absolute Jump/Call
Description: SJMP jumps unconditionally to the address specified reladdr. Reladdr must be within -  Applications that need to access the entire program memory from 0000H to FFFFH use long
128 or +127 bytes of the instruction that follows the SJMP instruction absolute jump.
 Since the absolute address has to be specified in the op-code, the instruction length is 3 bytes
The remaining relative jumps are conditional jumps (except for JMP @ A+DPTR). This jump is not re-locatable.
Example: -
Operation: LJMP
Function: Long Jump
Syntax: LJMP code address.
2. Short Absolute Jump
Description: LJMP jumps unconditionally to the specified code address.
 In this case only 11bits of the absolute jump address are needed. The absolute jump address
is calculated in the following manner.
Another classification of jump instructions is
 In 8051, 64 kbyte of program memory space is divided into 32 pages of 2 kbyte each.
1. Unconditional Jump
The hexadecimal addresses of the pages are given as follows:-
2. Conditional Jump
1. The unconditional jump is a jump in which control is transferred unconditionally to the target
location.
a. LJMP (long jump). This is a 3-byte instruction. First byte is the op-code and second and third bytes
represent the 16-bit target address which is any memory location from 0000 to FFFFH eg: LJMP
3000H
b. AJMP: this causes unconditional branch to the indicated address, by loading the 11 bit address to 0
 It can be seen that the upper 5bits of the program counter (PC) hold the page number and the -10 bits of the program counter. The destination must be therefore within the same 2K blocks.
lower 11bits of the PC hold the address within that page. c. SJMP (short jump). This is a 2-byte instruction. First byte is the op-code and second byte is the
 Thus, an absolute address is formed by taking page numbers of the instruction (from the relative target address, 00 to FFH (forward +127 and backward -128 bytes from the current PC value).
program counter) following the jump and attaching the specified 11bits to it to form the 16-bit To calculate the target address of a short jump, the second byte is added to the PC value which is
address. address of the instruction immediately below the jump.
Advantage:
The instruction length becomes 2 bytes.
Example of short absolute jump: -
2. Conditional Jump instructions. Operation: JNZ

Function: Jump if Accumulator Not Zero
Syntax: JNZ reladdr
Description: JNZ will branch to the address indicated by reladdr if the Accumulator contains any
value except 0. If the value of the Accumulator is zero program execution continues with the
instruction following the JNZ instruction.
Operation: JZ
Function: Jump if Accumulator Zero
All conditional jumps are short jumps.
Syntax: JNZ reladdr
Description: JZ branches to the address indicated by reladdr if the Accumulator contains the value 0.
Operation: JNC
If the value of the Accumulator is non-zero program execution continues with the instruction
Function: Jump if Carry Not Set
following the JNZ instruction.
Syntax: JNC reladdr
Description: JNC branches to the address indicated by reladdr if the carry bit is not set. If the carry bit
Operation: DJNZ
is set program execution continues with the instruction following the JNB instruction.
Function: Decrement and Jump if Not Zero
Syntax: DJNZ register, reladdr
Operation: JC
Description: DJNZ decrements the value of register by 1. If the initial value of register is 0,
Function: Jump if Carry Set
decrementing the value will cause it to reset to 255 (0xFF Hex). If the new value of register is not 0
Syntax: JC reladdr
the program will branch to the address indicated by relative addr. If the new value of register is 0
Description: JC will branch to the address indicated by reladdr if the Carry Bit is set. If the Carry Bit
program flow continues with the instruction following the DJNZ instruction.
is not set program execution continues with the instruction following the JC instruction.
Operation: CJNE
Operation: JNB
Function: Compare and Jump If Not Equal
Function: Jump if Bit Not Set
Syntax: CJNE operand1,operand2,reladdr
Syntax: JNB bit addr, reladdr
Description: CJNE compares the value of operand1 and operand2 and branches to the indicated
Description: JNB will branch to the address indicated by reladdress if the indicated bit is not set. If the
relative address if operand1 and operand2 are not equal. If the two operands are equal program flow
bit is set program execution continues with the instruction following the JNB instruction.
continues with the instruction following the CJNE instruction. The Carry bit (C) is set if operand1 is
less than operand2, otherwise it is cleared.
Operation: JB
Function: Jump if Bit Set
Syntax: JB bit addr, reladdr
Description: JB branches to the address indicated by reladdr if the bit indicated by bit addr is set. If
the bit is not set program execution continues with the instruction following the JB instruction.
Fig: 2.4: Jump Instruction Ranges
2.5. 1 Bit level jump instructions
 Bit level JUMP instructions will check the conditions of the bit and if condition is true, it
jumps to the address specified in the instruction.
 All the bit jumps are relative jumps.
RET instruction
2.5.2 Subroutine CALL and RETURN Instructions RET instruction pops top two contents from the stack and load it to PC.
Subroutines are handled by CALL and RET instructions There are two types of CALL instructions
Call instructions may be included explicitly in the program as mnemonics or implicitly included using
hardware interrupts.
Subroutine: Subroutine is a standalone program or small program in a main program 2.5.3 Calls and Stack
“A Subroutine is a program that may be used many times in the execution of a larger program.The
subroutine could be written into the body of the main program everywhere it is needed resulting in the 1. A call, hardware or software when initiated, causes a jump to the address where the
fastest possible code execution.” subroutine is located.
2. At the end of the subroutine the program resumes operation at the opcode address
1. LCALL address (16 bit) immediately following the call.
 This is long call instruction which unconditionally calls the subroutine located at the 3. Call can be located anywhere in the program space and used many times.
indicated 16 bit address. 4. The stack area of internal RAM is used to automatically store the address, called the return
 This is a 3 byte instruction. address, of the instruction found immediately after the call.
 The LCALL instruction works as follows. 5. Stack and stack pointer are often used to designate the top of the stack area in RAM that is
pointed to by the stack pointer
2. ACALL address (11 bit)

This is absolute call instruction which unconditionally calls the subroutine located at the indicated 11
bit address. This is a 2 byte instruction. The SCALL instruction works as follows.
Fig 2.5 : Storing and Retrieving Return address
5. But when '0' is written to the latch, the pin is pulled down by the lower MOSFET.
Hence the output becomes zero. When the control is '1', address/data bus controls the
output driver MOSFETs. If the address/data bus (internal) is '0', the upper MOSFET is
'off' and the lower MOSFET is 'on'.
6. The output becomes '0'. If the address/data bus is '1', the upper transistor is 'on' and
the lower transistor is 'off'.
2.6 I O port programming 7. Hence the output is '1'. Hence for normal address/data interfacing (for external
memory access) no pull-up resistors are required. Port-0 latch is written to with 1's
when used for external memory access
1. I/O Port pins, Ports and Circuits: One major feature of a microcontroller is versatility
built into the I/O circuits that connect the 8051 to the outside world.
Port-1
2. Out of 40 pins 24 pins may each be used for one of two entirely different functions
yielding a total pin configuration of 64.
3. But the port pins have been multiplexed to perform different functions to make 8051
as 40 Pin IC
The port pin circuitry is as shown below
Port-0
Fig 2.7 : Port 1 Structure

1. Port-1 has 8 pins (P1.1-P1.7) .The structure of a port-1 pin is shown in fig Fig.2.7
2. Port-1 does not have any alternate function i.e. it is dedicated solely for I/O
Fig. 2. 6 : Port -0 interfacing. When used as output port, the pin is pulled up or down through internal
1. Port -0 has 8 pins (P0.0-P0.7).The structure of a Port-0 pin is shown in Fig.2.6 ..Port- pull-up.
0 can be configured as a normal bidirectional I/O port or it can be used for 3. To use port- 1 as input port, '1' has to be written to the latch. In this input mode when
address/data interfacing for accessing external memory. '1' is written to the pin by the external device then it reads fine.
2. When control is '1', the port is used for address/data interfacing. When the control is 4. But when '0' is written to the pin by the external device then the external source must
'0', the port can be used as a normal bidirectional I/O port. Let us assume that control sink current due to internal pull-up. If the external device is not able to sink the
is '0'. current the pin voltage may rise, leading to a possible wrong reading.
3. When the port is used as an input port, '1' is written to the latch. In this situation both
the output MOSFETs are 'off'. Hence the output pin floats. This high impedance pin
can be pulled up or low by an external source.
4. When the port is used as an output port, a '1' written to the latch again turns 'off' both
the output MOSFETs and causes the output pin to float. An external pull-up is
required to output a '1'.
Port-2
Note:
1. Port 1, 2, 3 each can drive 4 LS TTL inputs.
Fig 2.8: Port 2 Structure 2. Port-0 can drive 8 LS TTL inputs in address /data mode. For digital output port, it needs
external pull-up resistors.
3. Ports-1,2and 3 pins can also be driven by open-collector or open-drain outputs.
1. Port-2 has 8-pins (P2.0-P2.7) . The structure of a port-2 pin is shown in Fig 2.8  Each Port 3 bit can be configured either as a normal I/O or as a special function bit.
2. Port-2 is used for higher external address byte or a normal input/output port. The I/O Reading a port (port-pins) versus reading a latch.
operation is similar to Port-1.  There is a subtle difference between reading a latch and reading the output port pin.
3. Port-2 latch remains stable when Port-2 pin are used for external memory access. The status of the output port pin is sometimes dependant on the connected load.
Here again due to internal pull-up there is limited current driving capability.  For instance if a port is configured as an output port and a '1' is written to the latch,
the output pin should also show '1'.
Port-3  If the output is used to drive the base of a transistor, the transistor turns 'on'. If the
port pin is read, the value will be '0' which is corresponding to the base-emitter
voltage of the transistor.
 Reading a latch: Usually the instructions that read the latch, read a value, possibly
change it, and then rewrite it to the latch. These are called "read-modify-write"
instructions.
2.6.1 Programs
1. Write a program to add the values of locations 50H and 51H and store the result in locations in 52h
and 53H.
ORG 0000H ; Set program counter 0000H
Fig 2.9: Port 3 Structure MOV A,50H ; Load the contents of Memory location 50H into A
ADD ADD A,51H ; Add the contents of memory 51H with CONTENTS A
1. Each pin of Port-3 can be individually programmed for I/O operation or for alternate
MOV 52H,A ; Save the LS byte of the result in 52H
function. The alternate function can be activated only if the corresponding latch has
been written to '1'. MOV A, #00 ; Load 00H into A
2. To use the port as input port, '1' should be written to the latch. This port also has ADDC A, #00 ; Add the immediate data and carry to A
internal pull-up and limited current driving capability. MOV 53H,A ; Save the MS byte of the result in location 53h
3. Alternate functions of Port-3 pins – END
2. Write a program to subtract a 16 bit number stored at locations 51H-52H from 55H-56H and store 4. Write a program to add two Binary Coded Decimal (BCD) numbers stored at locations 60H and
the result in locations 40H and 41H. Assume that the least significant byte of data or the result is 61H and store the result in BCD at memory locations 52H and 53H. Assume that the least significant
stored in low address. If the result is positive, then store 00H, else store 01H in 42H. byte of the result is stored in low address.
ORG 0000H ; Set program counter 0000H ORG 0000H ; Set program counter 0000H
MOV A, 55H ; Load the contents of memory location 55 into A MOV A,60H ; Load the contents of memory location 6.0.H into A
CLR C ; Clear the borrow flag ADD A,61H ; Add the contents of memory location 61H with contents of A
SUBB A,51H ; Sub the contents of memory 51H from contents of A DA A ; Decimal adjustment of the sum in A
MOV 40H, A ; Save the LSByte of the result in location 40H MOV 52H, A ; Save the least significant byte of the result in location 52H
MOV A, 56H ; Load the contents of memory location 56H into A MOV A,#00 ; Load 00H into .A
SUBB A, 52H ; Subtract the content of memory 52H from the content A ADDC A,#00H ; Add the immediate data and the contents of carry flag to A
MOV 41H, A; Save the MSbyte of the result in location 41. MOV 53H,A ; Save the most significant byte of the result in location 53:,
MOV A, #00 ; Load 005 into A END
ADDC A, #00 ; Add the immediate data and the carry flag to A
MOV 42H, A ; If result is positive, store00H, else store 0lH in 42H 5. Write a program to clear 10 RAM locations starting at RAM address 1000H.
END
ORG 0000H ;Set program counter 0000H
MOV DPTR, #1000H ;Copy address 1000H to DPTR CLR A ;
3. Write a program to add two 16 bit numbers stored at locations 51H-52H and 55H-56H and store the Clear A MOV R6, #0AH ;Load 0AH to R6 again:
result in locations 40H, 41H and 42H. Assume that the least significant byte of data and the result is MOVX @DPTR,A ;Clear RAM location pointed by DPTR
stored in low address and the most significant byte of data or the result is stored in high address. INC DPTR ;Increment DPTR
DJNZ R6, again ;Loop until counter R6=0
ORG 0000H ; Set program counter 0000H END
MOV A,51H ; Load the contents of memory location 51H into A
ADD A,55H ; Add the contents of 55H with contents of A 6. Write a program to compute 1 + 2 + 3 + N (say N=15) and save the sum at70H
MOV 40H,A ; Save the LS byte of the result in location 40H
MOV A,52H ; Load the contents of 52H into A ORG 0000H ; Set program counter 0000H N EQU 15 MOV R0,#00 ;
ADDC A,56H ; Add the contents of 56H and CY flag with A Clear R0
MOV 41H,A ; Save the second byte of the result in 41H CLR A ; Clear A
MOV A,#00 ; Load 00H into A again: INC R0 ; Increment R0
ADDC A,#00 ; Add the immediate data 00H and CY to A ADD A, R0 ; Add the contents of R0 with A
MOV 42H,A ; Save the MS byte of the result in location 42H CJNE R0,#N,again ; Loop until counter, R0, N
END MOV 70H,A ; Save the result in location 70H
END
Microcontroller Notes:18EE52 2020_2021
7. Write a program to multiply two 8 bit numbers stored at locations 70H and 71H and store the result
at memory locations 52H and 53H. Assume that the least significant byte of the result is stored in low
address.
ORG 0000H ; Set program counter 0000H
MOV A, 70H ; Load the contents of memory location 70h into A
MOV B, 71H ; Load the contents of memory location 71H into B
MUL AB ; Perform multiplication
MOV 52H,A ; Save the least significant byte of the result in location 52H
MOV 53H,B ; Save the most significant byte of the result in location 53
END
Outcomes
At the end of the Module, the students will be able to:

 CO1: Interpret the architectural features of 8051 microcontroller and its peripherals, Memory
organization, memory interfacing and looping instructions. (L4) MODULE 1, 2
 CO2: Develop 8051 programs in assembly language to solve arithmetic and logical programs. (L3)
MODULE 1, 2
Department of Electrical & Electronics Engineering, ATMECE, Mysuru Page 31

MODULE 2: Assembly Programming and Instruction of 8051

Uploaded by

Copyright:

Available Formats

MODULE 2: Assembly Programming and Instruction of 8051

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MODULE 2: Assembly Programming and Instruction of 8051

Uploaded by

Copyright:

Available Formats

Microcontroller Notes:18EE52 2020_2021 Microcontroller Notes:18EE52 2020_2021

2.2.1 The lst (list) file

3. DB (DEFINE BYTE): The DB directive is used to define an 8 bit data. DB directive

2.4 Arithmetic, logic instructions and programs i. MOV R3, 65H

1. Data transfer instructions i. MOV 47H, 65H

3. Logical instructions g. Move the contents of an external memory to A or A to an external memory

1. Data transfer instructions. h. Move the contents of program memory to A

2.4.1 Arithmetic instructions

CY AC and OV flags will be affected by this operation.

d) Division: Increment: Increments the operand by one.

e) DA A (Decimal Adjust After Addition) 2.4.2 Logical Instructions

Eg 1: MOV A,#23H ANL A, Rn

MOV R1,#55H ANL A,DIRECT

ADD A,R1 // [A]=78 ANL A,@Ri

DA A // [A]=78 no changes in the accumulator after da a ANL DIRECT,A

ADD A,R1 // [A]=ABh

XRL A,#DATA CPL A

2. Conditional Jump instructions. Operation: JNZ

Fig: 2.4: Jump Instruction Ranges

2.5. 1 Bit level jump instructions

2. ACALL address (11 bit)

Fig 2.5 : Storing and Retrieving Return address

Fig 2.7 : Port 1 Structure

At the end of the Module, the students will be able to:

Department of Electrical & Electronics Engineering, ATMECE, Mysuru Page 31

You might also like