⇌ pp

Centricast Materials for

High-Temperature Service
J. HUBER, D. JAKOBI
Schmidt + Clemens GmbH & Co. KG
Lindlar, Germany

The latest reformer tube materials offer improved creep rupture strength, longer tube life,
improved heat transfer, reduced tube skin temperature and lower fuel consumption. This paper
discusses the development of centricast materials for high-temperature service in steam reformer
furnaces.

S
team reforming furnaces are an integral part of
syngas process plants. They are also one of the
costliest pieces of equipment in the plant, in terms of
both capital and maintenance cost. Reformers generally
contain several hundred vertically oriented straight
centrifugally cast tubes, commonly known as reformer
tubes. These tubes have a significant impact on
replacement cost and can be a major cause of plant
unavailability, especially in the case of unexpected failures.
Reformer tubes operate at severe conditions and the
development in steam reformers has resulted in
increasingly high operating temperatures and pressures.
While reformer tubes operate at high temperatures and
internal pressures, the primary cause of tube failure is creep
damage (Fig. 1). However, reformer tubes are subjected to
other life-limiting mechanisms, such as overheating and
thermal shock. Consequently this is one of the major
concerns of a plant operator.
During the life of a reformer tube, it will also experience a
significant number of full thermal and pressure cycles
caused by plant start-ups and shut-downs. The cumulative
effect of these cycles can be very damaging and lead to
accelerating creep cracking.
The phenomenon of creep is caused by progressive
alteration of the material matrix. Dislocation flow through
the alloy gathers at the grain boundaries and causes voids.
These voids align and subsequently form micro cracks. Fig. 1: Alloy requirements

- 117 -
 J. Huber, D. Jakobi

Therefore, not only for a sensible economic balance but also to maintain high levels of reliability, structural
integrity and safety, operators would like to use the most advanced materials for their reformer tubes and
associated outlet components.
Experience shows that reformer tube assemblies, produced by centrifugal casting in heat-resistant materials,
are in the very best position to withstand the ever more rigorous operational conditions. Schmidt + Clemens
(S+C) has been incorporating the latest improvements and innovations in the design of new tube materials.
The very high degree of continuous improvements of S+C researchers in applying new features for the
optimum and correctly balanced properties is the basis for S+C’s global leading position in this field.
Extensive feedback of operating data, combined with a close relationship to a large number of operators, has
provided and continues to provide S+C with substantial background for yet more efficient tube materials.
Centrifugally- or spun-cast materials are the preferred choice for reformer tubes which are working under
severe operational conditions. The spun-cast materials contain around 0.4 wt-% carbon and therefore provide
very good creep strength. Over the years, special cast alloys with increased creep strength have been
developed to allow tube wall thickness to be reduced and to increase resistance to overheat and give longer
tube service life.
Modern alloys such as the HP types that have been available since the early 80s all contain a large amount of
chromium and nickel (Table 1). This contributes to strength and corrosion resistance at high temperature.

Table 1
Nominal Composition of Principal Alloys Used for Tubular Reformers
Common name (ACI) C% Cr % Ni % Nb % Other S+C Centralloy® grade
HP-Nb 0.40 25.0 35.0 1.0 – G 4852
HP-Micro-alloy 0.45 25.0 35.0 1.0 Micro-alloy additions G 4852 Micro
HP- Micro-alloy 0.45 25.0 35,0 1.0 Micro-alloy additions G 4852 Micro R

Alloys rely upon creep strengthening by the formation of carbides in the microstructure. The microstructure
typically consists of austenitic dendrites surrounded by eutectic carbides in the interdendritic region. In
addition to a network of primary carbides forming on the grain boundaries during solidification, fine secondary
carbide precipitates form in the austenite at service temperature.
In addition to chromium carbides, the HP-Nb type alloys usually also precipitate primary and secondary
niobium carbides. The HP-Microalloy type material has small additions of strongly carbide-forming elements,
particularly titanium and zirconium and also rare earth elements, which are added to the base HP-Nb Modified
Alloy. The strengthening effect in the HP-Microalloy materials is achieved by the phenomenon known as
“synergism”. This means that if two additions are both known to have
a strengthening effect, when added together in only small amounts,
secondary primary
M C
the combined effects is greater than the summation of their effects.
23 6 carbides
In the latest generation of the HP-Microalloy material, S+C’s
Centralloy® G 4852 Micro R, small controlled additions of strongly
carbide-forming elements cause precipitation of very fine, nano-sized
(Nb,Ti)(C,N) particles during exposure to operating conditions.
These are uniformly dispersed in the matrix (Fig. 2).
However, to obtain long-lasting high-temperature strength it is
important to balance the chemical composition of the alloy, since the
500nm
secondary key requirement is to achieve an optimal precipitation pattern as well
M(C,N) as to tailor the micro-alloying additions.
Fig. 2: TEM micrograph of typical MATERIAL DEVELOPMENT
precipitates in Centralloy
G 4582 Micro R material The task to develop such an alloy was a clear request from the
aged at 900ºC syngas industry to provide a material with significantly improved

118 Nitrogen+Syngas 2011 International Conference (Düsseldorf, 21-24 February 2011)

 Centricast Materials for High-Temperature Service

Fig. 3: Parametric stress rupture strength of Centralloy® G 4852 Micro and G 4852 Micro R
creep rupture properties compared with those of the typically used materials. With the support of its alliance
partners, S+C started a vigorous R&D program and the result can be summarised, as follows:
 S+C generated a unique specification for the Centralloy® G 4852 Micro R material with
substantially improved creep rupture strength compared to the conventional reformer tube
materials (Fig. 3).
 The material has small controlled additions of strongly carbide-forming elements, which are
added to the base HP-Nb modified alloy. The balance of elements leads to intragranular
precipitation of secondary nano-size particles. In general, the nucleation of secondary carbides
is promoted in the “as cast” structure and growth is inhibited when the material is aged. The
even dispersion and the size of such particles (in particular the nano particles) significantly
prolong the secondary stage and therefore the onset of creep.
 Alloy characterisation and micro-structural analysis were performed with sophisticated
equipment such as, FGM-SEM-EDX, TEM-EDX, etc.
 New melting and casting techniques were established to guarantee the improved creep
properties.
 S+C developed a special weld material based on matching chemistry. The weld material and
the weld joints have been evaluated by the Notified Body (TÜV).

BENEFITS OF CENTRALLOY® G 4852 MICRO R

The lifetime of the tubes operated within the typical steam reformer environment, is determined by the
available creep rupture strength of the material, which in turn determines the minimum sound tube wall
thickness (MSW) necessary to design a tube.
Standards have been established that a design life of 100,000 hours (approx. 11 years) was reasonable and
therefore one has to establish the stress which an alloy can withstand at given design temperature and
pressure for 100,000 hours without failure.
Naturally, the 100,000 hour design value is theoretical. It assumes constant non-stop operation of the furnace
always within the predetermined design conditions. Furthermore, the effects of any interruptions are not
considered, even though it is well known that each shut-down of a furnace will shorten the tube life.
The most popular method is the equation proposed in the American standard API RP 530:

Nitrogen+Syngas 2011 International Conference (Düsseldorf, 21-24 February 2011) 119

 J. Huber, D. Jakobi

OD x P
MSW = ––––––– (with fixed OD)
2Sa + P
ID x P
MSW = ––––––– (with fixed ID)
2Sa - P
where:
OD / ID = tube size (mm); P = design pressure (MPa)
Sa = allowable 100,000 stress rupture value (lower limit of the scatter band, 95%
confidence interval).
Nevertheless, this 100,000-hour design basis works well. Sufficient compensations are built into the various
calculations with the result that the theoretical continuous life of 11 years is close to the life actually achieved
in normal operation. When the furnace is operated within the limits of the pre-determined design conditions,
the service life can even be significantly extended.
The characteristic Larson Miller curve (parametric stress rupture strength) for the alloy Centralloy ® G 4852
Micro and the recently improved material Centralloy ® G 4852 Micro R is shown in Fig. 3.
This improved alloy Centralloy® G 4852 Micro R was introduced and put into service in several operating
plants in 2005, and has been commercially available since 2007. Over the past few years, S+C has supplied
reformer tubes in Centralloy® G 4852 Micro R material for many major projects around the world, with the
thinnest tube wall possible. Longer tube life and more reliable performance under adverse conditions (such as
a high number of start-up/shut-downs, overheating, hot spots due to catalyst performance, etc.) are expected.
The material offers customers a range of benefits or combinations of benefits from which to choose. These
include:
 Increased lifetime
By retaining the existing tube design, (dimensional parameters) and operating conditions, this
alloy substantially increases the lifetime of the tubes.
 Process improvements
By maintaining the existing reformer tube outside diameter in combination with the higher
strength of this alloy, it is possible to reduce the MSW. This subsequently increases the tube
inside diameter, which allows additional process gains through increased catalyst volume and
improved heat transfer. Results of exemplary calculations are given in Table 2. The reduced
MSW results additionally in an increased resistance to thermal shock.
Table 2
Influence of the Creep Rupture Strength on the Minimum Sound
Wall Thickness (MSW), Catalyst Volume and Tube Weight
Min. stress to rupture Tube weight
Centralloy® G MSW (mm) ID (mm) Catalyst volume
at 100,000 h (MPa) (kg/m)
4852 18.3 11.2 101.0 Reference 33.9
4852 Micro 21.2 9.8 103.8 + 5.6% 30.3
4852 Micro R 24.6 8.5 106.4 +10.8% 26.9

Alternatively, if tube dimensions remain unchanged and the design remains based on the standard 100,000
hours, the higher creep strength of Centralloy® G 4852 Micro R allows an increase of more than 20°C in
operating temperature, which will result in significant capacity gains.
The thinner wall of tubes in Centralloy® G 4852 Micro R means less weight and less cost, providing a
commercial advantage, especially when nickel prices are high.
CONCLUSIONS
Operators of steam reforming furnaces can utilise the latest material developments, especially the significantly
improved creep rupture strength of Centralloy® G 4852 Micro R, to fully optimise their operation. This

120 Nitrogen+Syngas 2011 International Conference (Düsseldorf, 21-24 February 2011)

 Centricast Materials for High-Temperature Service

advanced material with optimal balanced chemical composition can either be incorporated in revamps on
existing units to increase capacity and raise unit profitability or can be used in new units to reduce the number
of tubes. Additional benefits include improved heat transfer, reduced tube skin temperature and lower fuel
consumption.
References
1. Gommans, R.; Jakobi, D.; Jimenez, J. L.: “State-of-the-art of materials and inspection strategies for reformer tubes
and outlet components”. 46th Annual Safety in Ammonia Plants and Related Facilities Symposium, Montreal, Canada
(2002).
2. Kawai, T.; Zaghloul, M. B.: “Design features, material selection and performance of steam reforming furnace”.
International Plant Engineering Conference (INPEC), Bombay (Nov 1984).
3. Shinoda, L. T.; Zaghloul, M. B.; Kondo, Y.: “The effect of single and combined addition of Ti and Nb on the structure
and strength of the centrifugally cast HK40 steel. Transactions ISIJ 18 (1978), 139.

This paper was previously published in Nitrogen+Syngas No 307 (November-December 2010).

Nitrogen+Syngas 2011 International Conference (Düsseldorf, 21-24 February 2011) 121