Owner’s manual

U.S. and Canada Version Model Year 2010

General considerations
This vehicle, which complies with the NHTSA/EPA certification standards, is equipped with advanced technology and is capable of
achieving high performance levels.
It is equipped with sophisticated active and passive safety systems (described below). Unless otherwise and specifically provided for
by Ferrari (see the Safety section) it is PROHIBITED to deactivate any safety system.

For proper driving, the following conditions must ALWAYS be met:

- The driver must be in good physical condition, and not under the influence of drugs or alcohol.
- The road regulations must be strictly observed.
- The common rules of caution must always be observed, in relation to the quality/performance of the vehicle, the places where you
are driving and the contingent situations.

Ferrari recommends reasonable and careful use of the vehicle. The driver MUST NEVER allow passengers to increase the risk
connected with driving (e.g., not using the safety systems, such as the seat belts) by failing to observe the mandatory safety rules
that apply to both the driver and the passengers. All occupants must wear their seat belts at all times!

The vehicle MAY NOT be modified or tampered with for any reason whatsoever, as this would affect the standards required for
certification and safety.

The owner of the vehicle is obliged to carefully maintain the vehicle in compliance with the recommended maintenance schedule.

The driver must always pay attention to the warnings signals in the vehicle, in particular to the dashboard warning lights. Even in
cases where the warning lights do not indicate a situation of immediate danger, the driver must always be careful and consider the
possible consequences of the malfunction and the type of information signaled.

Even in the event of routine operations, such as refueling, the driver must take all necessary precautions and check for any spilling
of flammable liquid. These precautions must be taken even if the operation is performed by others. Before starting off, always verify
that the door closing systems are functioning, not only by checking that the relative warning lights are off, but also by trying to
operate them by hand.
The driver must be fully knowledgeable with the vehicle and its controls, so as to handle and drive it as required. Knowledge of the
vehicle can be achieved/improved by attending the driving courses held by Ferrari, which are recommended.

2
 Introduction

The names taken from the sports and racing world (e.g., F1, SPORT, RACE) only refer to the technology from which they derive or
to specific vehicle set-ups and they do not authorize the driver to behave improperly while driving.

These above only refers to some general issues that will be specifically dealt with in this Owner’s Manual.

THE NHTSA’S TOLL-FREE AUTO SAFETY HOTLINE

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform
the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ferrari S.p.A.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it
may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer,
or Ferrari S.p.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153),
(Media inquired: 202-366-9550); go to http://www.safercar.gov;
or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE., West Building Washington, DC 20590.
You can also obtain other information about motor vehicle safety from http://www.safercar.gov.

THE TRANSPORT CANADA TOLL-FREE AUTO SAFETY HOTLINE

If the affected vehicle is not repaired free of charge to you and within a reasonable time, you may submit a written complaint to Head
of Recalls, Road Safety and Motor Vehicle Regulation, Transport Canada, 2780 Sheffield Road, Ottawa, Ontario KIB 3V9. You may also
telephone Transport Canada at (613) 993-9851.

FUELS CONTAINING ALCOHOL

For its fuel injection systems, Ferrari uses components and materials of very high quality. However, no specific tests have been
carried out to assure the reliability of the system when using fuel containing alcohol. Consequently, we recommend that our
customers do not use fuel containing alcohol on Ferrari vehicles.

3
 Because of the high power generated Consulting the Manual Advice for Emergency situations
WARNING by the engine, we recommend
that the vehicle only be used by This manual refers to vehicles with two Provides useful advice for solving
experienced drivers. types of gearbox: problems that may occur.
• Mechanical gearbox
Service • F1 electronically-controlled gearbox Care of the Vehicle
The information contained in this manual Some information may therefore vary Provides advice for cleaning, care and
is necessary to get to know your vehicle, depending on the model. routine maintenance of your vehicle.
use it properly and keep it in good To facilitate reading the manual, the
condition. topics have been divided into sections Table of Notes
Strictly following the instructions and chapters.
This table lists important notes contained
contained in this manual will help you get To further facilitate consultation, each in the Owner’s Manual.
the optimal results and satisfaction from section is identified by a specific color:
your vehicle.
We also recommend you have all the Glossary
General
service operations and checks performed Explains the main technical concepts.
by the Authorized Ferrari Dealers, Provides general information about your
as they have skilled staff and suitable vehicle.
equipment. Index
See the “Sales and Service Organization” Safety Allows you to quickly identify and locate
manual for the location of the Authorized the information required.
Describes the main safety systems in the
Ferrari Dealers.
vehicle.
The Ferrari Technical Service
Department is at your complete disposal
for any information and suggestions. About your vehicle
Provides all necessary information to use
the vehicle.

4
 Introduction

The important parts requiring particular Abbreviations/Meanings For an overview of the abbreviations
attention are easily identifiable in the contained in this manual, please see the
various sections. Some descriptions and terms with Glossary.
particular meanings are to be found in
Extreme caution required: this manual in an abbreviated form:
WARNING Failure to comply with the A.C.
instructions could cause hazardous
situations involving personal and Air Conditioning
vehicle safety!
ABS
Anti-lock braking system for the wheels
while braking
Important note:
Warning aimed at preventing any ASR
damage to the vehicle and Anti-skid regulation during acceleration
consequently hazards involving
personal safety. F1-Trac
Traction control derived from the
technologies used in the racing sector
Warning for environmental ECU
protection:
Electronic Control Unit
Useful advice to help protect the
environment. F1
Electronically-controlled gearbox,
designed with the same technology as
used in the racing sector.

TFT
Thin Film Transistor

5
Updating Warranty and Service Book “F1-SuperFast” gearbox
The high quality level of the vehicle Each new vehicle comes equipped with a The vehicle may come equipped with
is subject to constant technological “Warranty and Service Book”. an electronically-controlled gearbox
improvements. Therefore, there may be This contains the vehicle’s warranty system, controlled by means of the
differences between this manual and your terms and conditions. levers on the steering wheel.
vehicle. The Authorized Ferrari Dealers The default setting for the F1 gearbox
The Warranty and Service Book also
will be glad to provide you with all the is always “AUTO” mode.
indicates when periodic service is due
information about the updates.
according to the “MAINTENANCE Every time the vehicle is started, the
All specifications and illustrations SCHEDULE”. F1 gearbox is in the “AUTO easy
contained in this manual refer to exit” mode, unless the vehicle was in
those resulting as of the printing date. Vehicle event data “AUTO” mode when it was turned off.
Specifications may be changed without
Your vehicle’s driving and safety systems To exit the “AUTO easy exit” mode,
prior notice.
employ computers that monitor, and share operate one of the levers UP and
DOWN (when the vehicle is
Spare parts with each other, information about your
moving) or press the AUTO button on
vehicle’s operation. One or more of these
We recommend you use genuine Ferrari computers may store what they monitor, the center console.
parts, which can be obtained from your either during normal vehicle operation
Authorized Ferrari Dealer. or in a crash or near-crash event. Stored Even though the system can be used
information may be read and used by: in “AUTO” mode, it should not be
The Ferrari warranty may be voided if
repairs are performed using parts that - Ferrari North America, Inc. considered an automatic gearbox.
are not Genuine Ferrari Parts. - Ferrari S.P.A. Therefore, for proper use always follow
the instructions given in this manual.
- Service and repair facilities
- Law inforcement or government This new F1 gearbox generation reduces
agencies overall gearshifting times. Using the
- Others who may assert a legal right to elastic power of the transmission devices,
know, or who obtain your consent to through integrated electronic engine and
know such information. gearbox management, the F1-SuperFast
system enhances vehicle performance.

6
 Introduction

The different gearshifting stages (torque Use of the vehicle Engine exhaust, some of its
reduction and clutch disengagement, - Avoid using the vehicle for short trips. WARNING constituents, and certain vehicle
gear disengagement and engagement and components contain or emit
- Check that the tire pressure is correct.
subsequent clutch re-engagement) are chemicals known to the State of
actuated in sequence. - Proper periodic maintenance will California (CA) to cause cancer and
contribute to preserving your vehicle in birth defects and reproductive harm.
This results in extremely fast gearshifting,
full working order and to protecting the
which is reduced to 100 ms (measured as In addition, certain fluids contained
environment.
“acceleration gap”). in vehicles and certain products of
We therefore recommend that you
component wear contain or emit
respect the service due dates indicated
Environmental protection chemicals known to the State of CA
in the “MAINTENANCE SCHEDULE”.
to cause cancer and birth defects or
The following chapter contains Driving style other reproductive harm.
useful information for environmental - Do not accelerate during the starting Battery posts, terminals and related
protection. procedure. accessories contain lead and lead
compounds. Wash your hands after
Ferrari has designed and constructed a - Do not warm up the engine when the handling.
vehicle using technologies, materials and vehicle is stationary.
Used engine oil contains chemicals
devices capable of reducing some of the - Drive prudently and keep a proper that have caused cancer in laboratory
harmful impact on the environment. distance suited to the driving speed. animals. Always protect your skin by
Using your vehicle respecting the - Avoid sharp and frequent accelerations. washing thoroughly with soap and
environment will be your contribution - Turn off the engine if the vehicle is kept water.
towards environmental protection. stationary for long periods of time.
Fuel consumption as well as engine, - Shift gears using only 2/3 of the speed
gearbox, brake and tire wear mainly permitted for each gear.
depend on two factors:
- use of the vehicle The vehicle is equipped with
- driving style. WARNING emission control and monitoring
systems, which must always function
Both factors are influenced by the driver.
properly.

7
 This vehicle has been constructed in compliance with the federal environmental and safety standards.
Nevertheless, a few rules should be followed.
Particular attention must be paid to:
- Overheated components: high temperatures develop in the engine compartment in proximity of the exhaust system.
Do not park the vehicle on paper, grass, dry leaves or other flammable materials. They could catch fire if they come into contact
with hot parts of the exhaust system.
Do not fit additional heat shields or remove those fitted on the exhaust system.
Do not let flammable substances come into contact with the exhaust system.
- Moving parts on the vehicle, such as fan belts, etc. are always protected by appropriate systems.
Do not remove the guards or work on the moving parts without taking the due precautions.
- Pressurized systems on the vehicle, such as: the braking system, air conditioning and heating system, cooling system and
lubrication system, which may generate pressure internally.
Do not carry out any work which could cause gas or liquids to escape risking injury to persons and damage.
- Exhaust gas generated by the running engine may be hazardous, especially in closed spaces. As well as consuming oxygen, the
engine discharges carbon dioxide, carbon oxide and other toxic gases.
- The fuel is highly flammable and emits vapors which may be noxious if inhaled.
Do not use open flames or create sparks near the open fuel tank or in any other condition where fuel comes into contact with air.
- The oils used may also be flammable: take the same precautions as necessary for fuel.
- The fluid contained in the battery is poisonous, corrosive and flammable. Do not let it spill or come into contact with the skin,
eyes or objects. Do not use open flames or create sparks near the battery.

Always observe the various warnings contained in this manual.

8
1. General
2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index

10
 Vehicle keys
Alarm system
Emergency starting
Electronic alarm
Identification plates and labels
Dimensions and weights
Main engine specifications
Transmission ratios
Performance
Fuel Consumption
Electrical system
Wheels and Tires
Recommended lubricants
and fluids
Vehicle keys Key codes Alarm system
The vehicle is delivered with two identical A CODE CARD is supplied with the keys. The Ferrari CODE system
keys that can be used for: This card shows the following:
The vehicle is equipped with an electronic
- starting the vehicle - the electronic code to be used for immobilizer system (Ferrari CODE) which
“emergency starting” is automatically activated when the
- locking/unlocking the doors
(central locking) - the mechanical code for the keys, to be ignition key is removed.
given to your Authorized Ferrari The keys are equipped with an electronic
- activating/deactivating the alarm system
Dealer if you request duplicates of the device which transmits a coded signal to
- opening the luggage compartment. keys. the Ferrari CODE ECU. Once this ECU
The code numbers on the CODE has recognized the signal, the engine can
WARNING CARD must always be kept in a safe be started.
and protected place, not accessible This device complies with Part 15 of the
to others. Federal Communications Commission
We remind you that the emergency (FCC) Rules. Operation is subject to the
WARNING start procedure can only be following two conditions:
performed using the electronic code 1) the device may not cause harmful
found on the CODE CARD. interference
2) the device must accept any
In the event of a change of ownership,
In the event that the keys are lost or interference received, including
it is essential that the new vehicle
stolen, you can request a duplicate interference that may cause undesired
owner is provided with all the keys and
from your Authorized Ferrari Dealer operation.
with the CODE CARD.
(see section “Duplicating the keys”
Any modification to the equipement
on page 14).
not expressly authorized by the party
responsible for compliance could void
Make sure you record the code the user’s authority to operate the
WARNING numbers in the space provided in equipment.
the “Warranty and Service Book”.

12
 General

Operation
1
Each time the ignition key is removed �
�
2
from the 0 position, the protection system
activates the engine immobilizer.
- When starting the engine, with the key
in postion II press the ENGINE START
button on the steering wheel:

���
3
���
��� ���
�� �� 4
2) If the CODE warning light A remains - While driving, with the ignition key in

1) If the code is recognized, the CODE

on and the OBD warning light B does
not turn off after the ECU has
completed its diagnostic cycle, it
position II:
1) If the CODE warning light A
illuminates, it means that the system is
5
warning light A on the instrument means that the code has not been performing a self-diagnostic cycle. At
panel turns off within one second, recognized. In this case, it is advisable the first opportunity, you can stop and
while the OBD warning light B turns
off after about eighteen seconds, once
the ECU has completed its diagnostic
to turn the key back to position 0 and
then back to II. If the immobilizer
test the system: turn off the engine by
moving the ignition key to position 0,
6
device remains active, try with the then move the key back to position II.
cycle. In these conditions, the other key provided. The CODE warning light A will
protection system has recognized the

7
illuminate and should go off within
key code and deactivated the If you are still unable to start the one second. If the warning light stays
immobilizer. engine, use the emergency starting on, repeat the procedure described
procedure (see page 15) and contact previously leaving the key at 0 for
your Authorized Ferrari Dealer. more than 30 seconds.

8
13
 The codes of the keys that are not - extract the battery D, pushing it in the
If the problem persists, please contact
available when the new memorization direction of the arrow to slide it off the
your Authorized Ferrari Dealer.
procedure is performed will be deleted retaining cover E
from the memory, in order to prevent that
2) If the CODE warning light A flashes, any lost or stolen keys are used to start
it means that the vehicle is not � �
the vehicle.
protected by the immobilizer.
Each key supplied has its own Replacing radio operated control
WARNING specific code, which must be stored battery
in the memory of the system ECU.
If you press one of the three buttons and
Contact your Authorized Ferrari this does not activate the corresponding
WARNING Dealer immediately to have all the function, before replacing the batteries,
keys stored in the system memory. check for correct operation of the alarm
system functions using the other remote - fit a new battery of the same type,
Duplicating the keys control. observing the indicated polarity
To replace the remote control battery: - refit the key cover C.
If you request additional keys, provided
that the conditions to satisfy your request - detach the key cover C, prying it off with
are met, remember that the codes must be a small screwdriver at the points Do not use sharp tools to replace the
stored (up to a maximum of 8 keys) on all indicated by the arrow cover and be careful to avoid
the keys. damaging it.
Contact your Authorized Ferrari Dealer
There is risk of explosion if the
and bring the following with you: WARNING battery is replaced with an incorrect
- all the keys in your possession type.
- the CODE CARD for the Ferrari CODE Dispose of used batteries according
system to the instructions.
- a personal identity document
- the documents proving ownership of the �
vehicle.

14
 General

ready to count the number of times This procedure can be repeated an

1
Emergency starting
the OBD warning light flashes. unlimited number of times.
If the Ferrari CODE is unable to

2
4) As soon as the number of flashes is
deactivate the immobilizer: After an emergency starting procedure, it
equal to the first digit of your CODE
- the CODE warning light remains is advisable to contact your Authorized
CARD, depress the accelerator pedal
permanently on Ferrari Dealer to solve the problem.
and hold it until the OBD warning
Otherwise, you will have to perform the
- the OBD warning light goes off after light goes off (after approximately 4
emergency starting procedure every time
four seconds and comes back on
immediately afterwards
seconds), then release the accelerator
pedal.
the engine is started. 3
- the engine does not start. 5) The OBD warning light starts flashing
In this condition, the engine can only be again. As soon as the number of flashes
is equal to the second digit of your
started with the emergency procedure.

We recommend you read the whole pro-

CODE CARD, depress the accelerator
pedal and hold it.
4
cedure carefully before performing it. 6) Follow the same procedure for the
remaining digits in the code on the
If you make a mistake during the
emergency procedure, turn the key to
CODE CARD.
7) When the last digit has been entered,
5
position 0 and repeat the operation from hold the accelerator pedal down. The
point 1. OBD warning light comes on for 4
1) Read the 5-digit electronic code found
on the CODE CARD.
seconds and then goes off. You can
now release the accelerator pedal. 6
2) Turn the key to position II: at this 8) A quick flashing of the OBD warning
point, the CODE and OBD warning light (about 4 seconds) confirms that
the operation has been successful.
lights are on.
3) Fully depress and hold the accelerator 9) Start the engine. 7
pedal. Approximately 8 seconds later, If the OBD warning light remains on, turn
the OBD warning light will go off. the key to 0 and repeat the procedure from
Release the accelerator pedal and get step 1.
8
15
Electronic alarm - someone attempts to enter the vehicle When the electronic alarm is activated, the
from a window user may request opening of the luggage
The electronic alarm system performs the compartment; in this case, the motion and
- the power supply is disconnected
following functions: anti-lift sensors are temporarily
- the siren is disconnected
- remote control for central door locking/ deactivated.
unlocking - the vehicle is moved.
If the luggage compartment is then closed,
- perimeter surveillance, detecting the the sensors will be reactivated.
opening of doors and lids � If the direction indicators and the red LED
- motion surveillance, detecting intrusion on the dashboard flash 9 times when you
into the passenger compartment activate the alarm system: this means that
- vehicle movement surveillance. one of the doors or the front/rear lid is not
properly closed and therefore is not
protected by the perimeter surveillance.
Activation Check for correct closing of the doors,
To turn on the alarm system, press � rear/front lid and close the open one
button F on the key: without deactivating the alarm system: the
- the direction indicators flash once direction indicators flashing once indicate
that now the door or the front/rear lid is
- the system beeps
closed properly and is protected by the
- the red LED on the dashboard flashes perimeter surveillance.
- the central door locking system is
activated and the doors are locked. If the direction indicators flash 9 times
when the alarm system is activated
The alarm system is activated after
with doors, rear and front lids properly
approximately 25 seconds and the alarm
closed, it means that the self-diagnostic
is triggered if:
feature has detected a malfunction in
- a door is opened the system. Contact your Authorized
- the luggage compartment lid is opened Ferrari Dealer to have the system
- the engine compartment lid is opened checked.

16
 General

Deactivation Deactivating the motion sensing system Alarm memory

1
To deactivate the alarm system, press The motion sensing system can be If the CODE warning light appears on the

2
button G on the key: deactivated by pressing button H on the display when the vehicle is started, this
- the direction indicators flash twice roof panel. When this function is means that an intrusion has been
deactivated, the LED on the button will attempted.
- the system beeps twice
flash for about 3 seconds and then will The alarm system memory is reset by
- the red LED on the dashboard goes off turn off. turning the ignition key.
- the dome lights and the lights under the
doors turn on 3
- the central door locking system is
deactivated and the doors are unlocked.
Pressing button G twice unlocks the doors
and also turns on the low beams for
30 seconds.
� �
4
The alarm system is off and it is therefore

5
possible to get into the vehicle and to
start the engine.
If the remote control battery is dead, to
gain access to the vehicle, insert the key
into one of the two door locks, then turn
it to release the lock. The alarm siren will
start to sound.
6
Start the vehicle following the standard Deactivating the anti-lift alarm
procedures. The alarm siren will Pressing button I deactivates the anti-lift
deactivate. alarm. When this function is deactivated,
the LED on the button will flash for 7
about 3 seconds and then will turn off.

8
17
Identification plates and labels
A Assembly number plate
B Emission control data label
C Fuel label �
D Paintwork label �
�
E Oil level check label
F Engine oil type label � �
�
G Airbag label � �
� � �
H High voltage label � �
I Anti-freeze label � � �
�
L Tire pressure label � �
�
M Tire pressure and temperature �
monitoring system label
�
N V.I.N. plate
�
O Safety standard label
P Mercury content warning label
Q Battery master switch instruction label
R Engine type and number
S Chassis type and number
T Gearbox type and number
U Airbag maintenance label
V Child seat warning label
W Airbag label
X Weight sensor label

18
 General

A Assembly number plate C Fuel label F Engine oil type label

1
2
3

A87
8
bar
1.4

4
G Airbag label
B Emission control data label D Paintwork label
E Oil level check label
5
6
�

�
7
8
19
H High voltage label L Tire pressure label N V.I.N. plate

I Anti-freeze label M Tire pressure and temperature O Safety standard label

monitoring system label
A87
8

bar
1.4

20
 General

P Mercury content warning label R Engine type and number T Gearbox type and number
1
2
3

4
Q Battery master switch instruction label S Chassis type and number U Airbag maintenance label

5
6

7
8
21
V Child seat warning label X Weight sensor label

W Airbag label

22
 General

1
Dimensions and weights

2
Wheelbase 108.27 in. (2750 mm)
Max. length 183.66 in. (4665 mm)
Max. width 77.24 in. (1962 mm)
Max. height A 52.12 in. (1324 mm)
Front track B 66.53 in. (1690 mm) B 63.7 3
Rear track 63.7 in. (1618 mm)
Curb weight 3,777 lbs. (1715 kg *) 77.24
Curb weight
(F1)
3,810 lbs. (1730 kg *)
4
* with the vehicle fitted with the most
popular options available.
5

A
HGTE package
Max. height A
Front track B
51.73 in. (1314 mm)
66.81 in. (1697 mm)
108.27 6
183.66
7
8
23
Main engine specifications Transmission ratios
Engine Family AFEXV05.7LEV Gear ratios Differential bevel gear pair ratio
Type F140C 1 41 / 13 = 3.15
Number of cylinders 12 2 37 / 17 = 2.18
Cylinder bore 3.6 in. 3 36 / 23 = 1.57 4.18
Piston stroke 2.96 in. 4 32 / 27 = 1.19 (11 / 46)
Total displacement 5999 cm3 5 29 / 31 = 0.94
Compression ratio 11.2:1 6 25 / 33 = 0.76
Maximum RPM 8250 RPM R 41 / 14 = 2.93
RPM limiter 8400 RPM
Max. power 456 kW
(611 HP)
Corresponding RPM 7600 RPM
Max. torque 608 Nm
Corresponding RPM 5600 RPM

Performance
Gearbox type 0 - 100 km/h 0 - 200 km/h Max. speed
0 - 62 mph 0 - 124 mph
F1 Gearbox Version 3.7 sec 11 sec > 205 mph (> 330 km/h)
Mechanical Gearbox Version 3.7 sec 11 sec > 205 mph (> 330 km/h)

24
 General

For best fuel economy, shift gears at the

1
Fuel Consumption Shift Indicator Light (SIL) operating mode
(miles per US Gallon) following speeds: The graphic symbol A appears just before

F1 Gearbox Version
1st
2nd
-
-
2nd
3rd
10 mph (16 km/h)
15 mph (24 km/h)
reaching the speed recommended for
operating the UP lever (F1 gearbox
version) or for upshifting using the
2
City 11
gearshift lever (mechanical gearbox).
3rd - 4th 20 mph (32 km/h)
Highway 15 After shifting gears or after exceeding the
Average fuel consumption 12
4th
5th
-
-
5th
6th
25 mph (40 km/h)
30 mph (48 km/h)
indicated speed, the indicator turns off
even if no gearshift is performed.
3
Mechanical Gearbox Version
City 11
Highway 15 4
Average fuel consumption 12

These estimates are based on tests

performed on vehicles equipped with
frequently purchased optional equipment.
�
5
The fuel economy values are calculated
pursuant to the new EPA fuel economy
labeling procedure for 2008 and later
model years. You can also obtain
6
other information from http://www.
fueleconomy.gov.
Reminder: Your actual fuel consumption
may vary depending on your driving style
7
and habits, vehicle maintenance, optional
equipment installed, road and weather
conditions.
8
25
Electrical system Wheels and Tires (HGTE package)
Supply voltage 12 v
Wheel
Alternator Nippondenso 150 A
Front* Rear
Battery Fiamm 12V, 74 Ah, 440 A
8.5” J x 20” 11” J x 20”
Starter motor Nippondenso
*front wheel with reverse rim

Wheels and Tires Wheel with REVERSE RIM (HGTE package).

�������
The tire must be fitted and removed from the inner part
of the rim only to avoid damaging the rim and pressure
Wheel sensor!
Front Rear Spare This operation must be performed by skilled staff.
8” J x 19” 11” J x 20” 4.5” J x 20” Contact your Authorized Ferrari Dealer.
8” J x 20” optional 11” J x 20” 4.5” J x 20”

* Tires approved by Ferrari Inflation pressure (when cold)

Front Rear Spare tire Front Rear
Pirelli P Zero 245/40 ZR19 305/35 ZR20 32 psi (2.2 bar) 29 psi (2.0 bar)
145/60 ZR20 61 psi (4.2 bar)

* Always check your tires regularly for wear and damage.

26
 General

1
Optional tires Inflation pressure (when cold)
Front Rear Front Rear
Pirelli P Zero 245/35 ZR20 32 psi (2.2 bar) 2
Bridgestone RE 050 (Run Flat) 245/35 ZR20 305/35 ZR20 32 psi (2.2 bar) 32 psi (2.2 bar)
Goodyear Eagle 245/40 ZR19 305/35 ZR20 36 psi (2.5 bar) 36 psi (2.5 bar)
3
Snow tires Inflation pressure (when cold)
Front Rear Front Rear
Winter Pirelli 245/40 ZR19 305/35 ZR20 35 psi (2.4 bar) 32 psi (2.2 bar) 4
5
Tyres for HGTE package Inflation pressure (cold)
Front Rear Front Rear
Pirelli P Zero 245/35 ZR20 305/35 ZR20 32 psi (2.2 bar) 29 psi (2.0 bar)

In order to achieve the best vehicle performance and help ensure safety conditions,
6
replace all of the snows tires if they are worn.
Please contact your Authorized Ferrari Dealer when you have to fit snow tires.

7
8
27
Wheel Replacement Treadwear The traction grade assigned to this tire
WARNING is based on straight-ahead braking
The treadwear grade is a comparative traction tests, and does not include
We recommend you read the whole pro-
rating based on the wear rate of the tire acceleration, cornering, hydroplaning, or
cedure carefully before performing it.
when tested under controlled conditions peak traction characteristics.
on a prescribed government test course.
Wheel bolt 25.8 - 29.5 ft. lbs. For example, a tire graded 150 would Temperature
pre-tightening (35-40 Nm) wear one and one-half (1-1/2) times as The temperature grades are “A” (the
well on the government course as a tire highest), “B”, and “C”.
Wheel bolt 73.8 ft. lbs.
graded 100.
final tightening (100 Nm) Temperature grades represent the tire’s
The relative performance of tires depends resistance to the generation of heat and its
upon the actual conditions of their use, ability to dissipate heat under controlled
and may differ significantly from the norm indoor test wheel conditions. Sustained
Uniform tire quality grading due to variations in driving habits, service high temperature can cause the tire to
practices and differences in road deteriorate and can reduce tire life. In
All passenger car tires must conform to
characteristics and climate. Check your addition, excessive temperature can lead
Federal Safety requirements in addition to
tires regularly for wear. to sudden tire failure. Grade “C”
these grades.
corresponds to a level of performance
which all tires installed on passenger
Traction
DOT quality grades vehicles must meet under the Federal
The traction grades, from highest to Motor Safety Standard No. 109. Grades
Tires type Pirelli P Zero lowest, are “AA”, “A”, “B”, and “C”. “B” and “A” represent higher levels of
Tread wear 220 (front) These grades represent the tire’s ability to performance on the laboratory test wheel
stop on wet pavement under controlled than the minimum required by law.
160 (rear)
conditions on specified government test The temperature grade for this tire is
Traction AA surfaces of asphalt and concrete. Tires WARNING established for a tire that is properly
Temperature A marked “C” have poor traction inflated and not overloaded. Excessive
performance. speed, under-inflation, or excessive
loading, either separately or in
combination, can cause heat buildup
and possible tire failure.

28
 General

Run Flat tires (optional)

1
The vehicle can come equipped with
“Run flat” tires. This type of tire has a
reinforced side B which allows the vehicle
to continue traveling at moderate speed
2
(50 mph - 80 km/h), even after a puncture,
for a specific distance.
The instrument panel receives the “tire
puncture” information from the tire
�
3
pressure monitoring ECU, which monitors
the residual tire life and displays a warning
in the dedicated area of the TFT display If you are going to use standard tires
after 30 mi (50 km).
After 60 mi (100 km), a message warning
WARNING on a vehicle that was originally
equipped with “Run Flat” tires, you 4
must contact your Authorized
the driver to stop the vehicle will be
displayed (see “Tire pressure and Ferrari Dealer to have the

5
temperature monitoring system” on page 55). dashboard reprogrammed and to
prevent viewing warning messages
Observing the recommended wheel on the TFT display.
WARNING alignment values is essential in order Run Flat type tires cannot be fitted
to obtain the best performance and on the 599 GTB Fiorano with the
6
�������
�������

the longest life of these tires. HGTE package!

More information on these tires and
on the relative pressure monitoring
system can be found in the
“Carrozzeria Scaglietti” Owner’s
Manual. 7
8
29
Recommended lubricants and fluids
Parts to be refilled Quantity Fill with Ref. Page
Engine Total system capacity 12.68 qts. (12 l) HORSE POWER 161
SAE 10W-60
Oil level between Min. and Max. 1.58 qts. (1.5 l)
Oil consumption 1.06-2.11 qts./600 miles
(depending on driving conditions) (1.0 ÷ 2.0 l/1,000 km)
Gearbox and differential 5.28 qts. (5 l) TRANSAXLE SAE 75W-90 161
F1 gearbox system 1.06 qts. (1 l) DONAX TX 161
Braking and clutch system DONAX UB BRAKE FLUID 163
1.58 qts. (1.5 l)
F1 braking system DOT4 Ultra
Cooling circuit 6.34 US Gallon GLYCOSHELL at 50% 161
(24 l)
Hydraulic steering system 1.06 qts. (1 l) DONAX TX 163
Steering box 0.22 lbs. (100 g)
Fuel tank 27.74 US Gallon (105l) Premium Gasoline (91-94 A.K.I.) 71
Reserve 5.28 US Gallon (20 l) Unleaded fuel
Air conditioning and heating system -
Compressor 10.07 cu.in.(165 cc) DELPHI RL 488 “R 134 A”
Refrigerant 1.65 ± 0.11 lbs. (750 ± 50 g)
Windshield washer fluid tank 6.86 qts. (6.5 l) Windshield washer fluid 164

30
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
 Seat belts
Pretensioners
Child safety
Airbag
Side Airbag
Advanced Airbag System
ABS
CST
F1-Trac
Tire pressure and temperature
monitoring system
Seat belts Do not pass the seat belts over sharp
To help ensure optimal protection, keep WARNING edges. They could tear.
If used correctly, the seat belts, in the seat backrest in the upright position,
combination with the pretensioners, have make sure that your back is properly
Do not attach or pin anything onto
been designed to help protect the wearer resting on it and adjust the seat belt WARNING the seat belts. This could reduce
from a variety of impacts while firmly correctly, fitting it closely across your
their initial strength and cause them
securing the occupants within the chest and pelvis.
to tear in the event of a crash.
structure of the vehicle. The lap portion of the seat belt must be
fitted low across your pelvis, resting on Do not bring cutting edges in
Ferrari urges you to use the seat contact with a seat belt. They may
the pelvic bones. Take care that the lap WARNING

belts correctly fastened and adjusted get damaged and consequently

portion of the lap belt does not rest on
WARNING

at all times! the abdomen, as this can result in an break in the event of a collision.
increased risk of injuries. Adjust the seat If a seat belt has been brought in
Correct use of the seat belts can help
height to help keep the lap portion of the contact with a cutting edge, or has
reduce the risk of serious injury in
belt low on the pelvis.
WARNING

been used to pin something on it,

the event of an accident.
have it immediately replaced at your
All passengers must wear their seat Authorized Ferrari Dealer.
WARNING belts!

The seat belts are lap and shoulder seat

belts with automatic retractor and an
emergency inertia locking system on the
retractor unit, which is fitted with a
pretensioner.

34
 Safety

1
Adjusting the seat belt height
- Press button A to release the adjustment
device and move it to the desired
position.
�
2
�
� 3

4
- Always check that it is locked. The seat

5
belt is properly adjusted when it passes
- Make sure that it has clicked into place. - Avoid “slouching” positions, as this can
about mid-way between the end of the
- Position the seat belt correctly: the lap cause the lap portion of the seat belt to
shoulder and the neck. The lower part
portion of the seat belt must rest low on move up to the abdominal region.
must fit tightly across the pelvis and not
the abdomen. the pelvis, and lean onto the pelvic - The upper portion of the seat belt must

Fastening the seat belts

bones.

Do not use any objects (e.g., spring

be adjusted so that it passes over the
shoulder, mid-way between the end of
the shoulder and the neck.
6
Adjust the seat and seat backrest properly. clips, locks, etc.) that hold the seat belt
If the driver’s seat belt is not fastened,
- Grip the buckle B, slowly pull the belt away from your body.
when you turn the ignition key to
and insert the tang into its receptacle C.
Should the belt lock while pulling it, let - Pay attention that the lap portion of the
position II, the warning light D
illuminates.
7
it rewind slightly and then pull it again seat belt does not move up into the
without sharp movements. abdomen.

8
35
 Unfastening the seat belts Pretensioners
- Push the release button E.
The pretensioners are designed to activate
- Guide the seat belt buckle B back to its in the event of certain head-on collisions
rest position. of sufficient force, or in a side collision of
� sufficient force. The seat belt will rewind
a small amount just before the restraining
action begins, thereby helping to ensure a
proper hold around the occupant’s body.
Activation of a pretensioner is signaled by
the illumination of the warning light A on
the instrument panel.
�

�
�

If the passenger’s seat belt is not fastened

and the system detects the presence of an
adult in the passenger’s seat (according to
the Occupant Classification System), a
warning will appear on the TFT display.

Do not allow children to be held on Emergency tensioning device, seat

WARNING a passenger’s lap using only one seat belt load limiter
belt for both of them.
The seat belts in this vehicle are equipped
In the event of a crash, the weight of
with emergency tensioning devices (also
the adult would crush the child
called “pretensioners”) and load limiters.
against the seat belt.
This can result in serious injuries or
death for the child.

36
 Safety

After activation, the pretensioner no The seat belt is equipped with a load- Because of their size and shape, children
1
WARNING longer functions and cannot be limiting device, which is designed to are at greater risk for injuries than adults.
repaired, under any circumstances. reduce the restraining force exerted by Suitable restraint or safety systems must
Contact your Authorized Ferrari
Dealer for replacement.
the seat belts on the occupant’s body
during a collision. This device controls the
be used.
All person whose physical characteristics
2
force level with which the seat belt is (e.g., height, weight) meet the limit values
When a pretensioner is activated, a small released during a collision.
amount of smoke is released. This smoke provided by established legislation in each
is not harmful and does not indicate the
presence of a fire. Child safety
country must be protected by
approved restraint or safety systems (i.e.,
certified child seats, cradles, and cushions).
3
All work on any part of the safety In any case, you are advised to always use
Never drive with a child in a
system components must be certified child restraint systems bearing
rearward-facing child seat in the
WARNING

4
WARNING

performed only by an Authorized the proper test marking.

front seat if the "PASSENGER
Ferrari Dealer.
AIRBAG OFF" warning light is not Incorrect fastening of a child
illuminated. Airbag deployment can restraint system increases the risk of
It is not permitted to remove or make WARNING

cause serious injuries or death to a injury to the child in the event of a

modifications of any kind to the seat
belts, belt retractors and pretensioners.
Maintenance work involving strong
child in a rearward-facing child seat.
Established legislation in some
collision.

- The seat belts in the vehicle have been

5
countries already provides that
impacts, vibrations or heating of the
WARNING

designed and tested to protect persons

children under 12 years of age may
pretensioner area may activate them; weighing at least 79 lbs (36 Kg) and
not travel in the front passenger seat.
vibrations caused by road bumps will
not have this effect. Child seats may only be installed
with the seat fully lowered and
taller than 59 in. (1.50 m).
- To properly protect any passengers
6
Activation of the pretensioners only
WARNING

outside these limits, specific restraining

depends on the status of the seat belts pushed backward.
systems with dedicated belts or
and is not affected by the occupants’
7
accessories capable of adapting the
presence. Do not tamper with the seat belts or child’s position to the vehicle’s seat belts
If the seat belt is not fastened, the child restraint systems. must be fitted.
pretensioner will not activate, even if
the seat is occupied.

8
37
 To deactivate this feature, release the seat
For installation and use of a child restraint
belt buckle and allow the seat belt to
system, always follow the instructions that
retract completely.
the manufacturer of the devices is
required to supply. Always deactivate this feature prior
WARNING to using the seat belt for normal use.
Always follow the instructions supplied Having the retractor locked can be
with the child restraint system precisely. dangerous when the seat belt is used ��
Keep the instructions in the vehicle for directly restraining a passenger.
together with the documents and this
manual. Never use second-hand child If you must, in an emergency situation,
seats which are not provided with carry a child in a rearward-facing child
instructions for use. seat in the front passenger seat: �
In case of an accident, replace the child seat. - adjust the seat to the most rearward
position (avoiding contact with the
The passenger-side seat belt in this vehicle
interior)
is equipped with special retractors to help
properly fasten a child restraint. To install a - adjust the headrest to the lowest Installing a child seat with the key in
child restraint, pull the seat belt out possible position WARNING position II can result in induced
completely. The retractor will now only - install the child seat when the key is in injuries.
allow the seat belt rewinding and will not the 0 position, following the instructions
allow the seat belt to be pulled out. provided with the child seat - the extra weight applied on the seat
Follow the instructions on the child during child seat installation might delay
restraining system for proper installation in correct occupant classification if the child
the vehicle. seat is mounted with the key in position II

Check that the seat belt locking - always check that no objects are stuck
mechanism has been activated by trying to underneath the seat
pull out a small amount of seat belt with - always check that no objects are loose on
moderate force. If the system has been the floor, either in front, or behind the
activated, this should not be possible. seat
- check that no objects contact the seat

38
 Safety

- make sure that the “PASSENGER warning will also be temporarily viewed in If the “PASSENGER AIRBAG OFF”
1
AIRBAG OFF” warning light A on the the multifunction display in the instrument warning light is still not illuminated,
roof panel is illuminated and does not panel, but you may be busy with driving move the key to the 0 position and wait
flash and not notice it a few seconds. If , at restart, the lamp is
still not illuminated, call for assistance
2
Never drive with a child in a
WARNING rearward-facing child seat in the

�
��������
�������
front seat if the "PASSENGER
AIRBAG OFF" warning light is not 3
illuminated. Airbag deployment can
cause serious injuries or death to a
child in a rearward-facing child seat.

WARNING
Never carry a child in a adult’s lap. In
the event of a crash, the weight of the
4
adult could crush the child against
the seat belt (or the dashboard). This
could result in serious injuries or
death for the child. 5
This is a high-performance vehicle.
��������
- drive carefully and slowly avoiding any ������ WARNING You are strongly urged not to carry
hard braking and acceleration
- do not distract yourself from driving by
children in this vehicle, since they
can also be injured by hard
accelerations.
6
checking on the child. If you need to
check on the child's condition, stop the Always drive slowly and carefully
vehicle in a safe place when carrying a child. Hard
7
WARNING

- when it is not dangerous (e.g., stops at - if the “PASSENGER AIRBAG OFF” accelerations due to sport-style
“red” traffic lights) periodically check on warning light goes off, carefully stop the driving can be dangerous for
the “PASSENGER AIRBAG OFF” vehicle in a safe place. Check that no children, even if no crash occurs.
warning light status. If the “PASSENGER objects are stuck underneath or behind
AIRBAG OFF” warning light goes off, a the passenger seat.
8
39
 Children must always be seated in Transport of persons with disability
WARNING a child restraint system specifically If it is necessary to modify the advanced
designed for their size, and must be airbag system of your vehicle to
properly restrained. accomodate a person with disabilities,
Unrestrained occupants, including contact your Authorized Ferrari Dealer.
WARNING children, can be propelled against The advanced airbag system of your
the dashboard or the windshield by WARNING vehicle is not designed to protect
hard braking and by crash forces. adults with disability that require
This can result in serious injuries or deactivation of the passenger’s or
death. driver’s airbag.
Do not tamper with seat belts or If you or another occupant is an
WARNING child restraint systems. WARNING adult with a medical condition that
requires airbag deactivation, please
Established legislation in some contact your Authorized Ferrari
countries already provides that Dealer.
children under 12 years of age may not As long as the airbag is activated,
travel in the front passenger seat. WARNING persons with disability are advised
not to travel in the vehicle in order
The ignition key must always be to avoid the risk of serious injuries
WARNING turned to position 0 when installing a or death, even in minor crashes.
child seat on the front passenger seat.

40
 Safety

When the ignition key is turned to

1
Airbag Airbag system components
The airbag system is composed of two WARNING position II, the warning light C
The airbag is not a substitute for the illuminates. If no malfunctioning is
2
cushions that are designed to inflate
seat belts. Correct use of the seat detected, it will go off after 4
almost instantaneosly. One A, is on the
WARNING

belts, in combination with the seconds. If the warning light does

driver side, in the center of the steering
airbag, will offer protection for the not illuminate, if it remains on or if it
wheel, and the other B on the passenger
driver and passenger in the front illuminates while driving, contact
side, inside the dashboard.
seats in the event of a head-on
collision.
Front airbags cannot offer protection
your Authorized Ferrari Dealer
immediately. 3
in side crashes, certain front-angular
�
WARNING

crashes, roll over events or in

secondary impacts (if a second crash
happens after the airbags have been 4
deployed in a previous crash). The
seat belts are designed to help B
reduce the risk of injuries in roll
over events and secondary front
impacts.
5
A properly fastened seat belt is A
needed to help protect occupants in
roll over events and secondary front
impacts. 6
Front airbags are designed to not be
WARNING deployed in low severity frontal
crashes. The seat belts can help
reduce injuries in low severity
crashes. A properly fastened seat belt
7
is needed to help protect the
occupants in low severity frontal
crashes.
8
41
Operation The driver and passenger must
It is possible that the driver’s airbag is
The airbags are controlled by an ECU WARNING always fasten their seat belts and sit
deployed in a crash, and the passenger’s in an upright position, as far as
that is designed to activate them in the airbag is not deployed. This could
event of certain head-on collisions of possible away from the airbag, in
happen if the front passenger is order to help ensure protection in all
sufficient force. classified as a child by the Occupant types of collision.
In the case of a collision with an impact Classification System (see also page 50
for more details about the Occupant Always keep the backrest of your seat
force that causes deceleration exceeding in the upright position and sit with
Classification System).
WARNING

the value set for the internal sensor, the your back properly resting against it.
ECU will transmit a signal to deploy the
The driver and passenger are both
airbags. The airbags will begin to inflate, Do not modify the system components
advised not to travel handling objects
breaking the cover along the breakage line
WARNING

(e.g., beverage cans or bottles, pipes, or wiring, under any circumstances.

and will deploy completely in a few
etc.) that could cause injury in the
hundredths of a second. Once deployed, With the ignition key inserted and in
case of airbag deployment.
they will serve as protection between the WARNING position II, although the engine is off,
driver and/or passenger and the structures When the system is activated, gases are the airbags can still be activated when
that could cause injury. released in the form of fumes, together the vehicle is stationary if it is hit by a
The airbags deflate immediately moving vehicle.
with the gas used for inflating the
afterwards. airbags. Thus, even with the vehicle
The passenger airbag deployment is stationary, do not put children in the
These gases are not harmful. The
front seat. In addition, remember that
further influenced by the occupant’s presence of smoke is not indicative of a
if the ignition key is in position 0,
weight, as determined by the Occupant fire.
none of the safety devices (airbags or
Classification System (see also page 50 for
Always drive with your hands on the pretensioners) will be activated in the
more details about the Occupant
event of a collision. Failure of the
Classification System). WARNING rim of the steering wheel so that, in
airbags to inflate in these
If the front passenger is classified as being case of activation, the airbag can
circumstances is not indicative of a
a child by the Occupant Classification deploy without obstruction.
system malfunction.
System, the passenger airbag will never Driving with your hands inside the
Therefore, even with the vehicle
deploy, no matter how high the crash steering wheel rim or on the airbag
stationary, do not allow children to
cover increases the risk of injury for
WARNING

severity.
sit on the front seat.
your wrists and arms.

42
 Safety

To scrap the vehicle, please contact

1
Do not cut or tamper with the All the airbag system components must
your Authorized Ferrari Dealer to
connectors of the airbag harness or on be replaced after an accident that
have the airbag system deactivated
the airbag modules.

Never place an object over or near

caused airbag deployment.
and disposed of properly.
2
Following an accident not involving If the vehicle has been stolen or there
the airbag covers.
has been an attempted theft, have the
WARNING

airbag deployment, contact your

In the event that the airbags are airbag system checked by an
deployed, these objects would be
projected into the passenger
Authorized Ferrari Dealer to have the
system checked and any system
components that may be damaged or
Authorized Ferrari Dealer. 3
compartment at very high speed. The malfunctioning replaced. The airbag modules must be replaced
object will be transformed into a WARNING at the intervals indicated in the
projectile propelled in the passenger
compartment. This could cause
serious injuries.
WARNING
Damaged or defective components of
the airbag system cannot be repaired
and must be replaced.
“Warranty and Service Book” EVEN
if the vehicle was NOT involved in a
collision.
4
Never modify the airbag modules. Do Improper operations performed on The label E , on the right-hand side of the
not damage the airbag modules (for the system components may cause dashboard, bears the airbag system
5
WARNING

example pinning something onto failures or accidental deployment of expiration date. When this expiration date
them or pressing objects against their the airbags with consequent damage is approaching, contact your Authorized
covers). and injury, even fatal. Ferrari Dealer in order to have the
If, for any reason, an airbag cover gets system replaced.
damaged, have the airbag module
immediately checked by your
The airbag system components have
been specially designed only for this
specific vehicle model. Do not use them
6
Authorized Ferrari Dealer.
on a different vehicle model, as this
Activation of a damaged module may cause serious damage and

7
could cause serious or fatal injuries. consequent injury, even fatal, to the
occupants in the event of an accident.
Never remove the steering wheel. If
necessary, this procedure should only �
be performed by an Authorized Ferrari
Dealer.
8
43
The label F on the dashboard can be
removed.
�
�

Side Airbag
The airbags are not a substitute for
The labels G and H indicate the presence WARNING the seat belts. Correct use of the seat
of the airbag system. belts, with the supplementary action
of the side bags, will provide
protection in the event of a lateral Each side bag is composed of a cushion,
collision. wich has been designed to deploy almost
� Side bag system components instantaneously in order to protect the
occupant’s head in the event of a side
The side bag fitted on the vehicle impact.
WARNING was not designed to reduce the risk
of being hurled out in the event of When the ignition key is turned to
vehicle roll-overs.
WARNING position II, the warning light B will
illuminate. If no malfunctioning in
Your vehicle is equipped with 2 side bags, the airbag system is detected, it will
one in the driver-side door A, and the go off after 4 seconds. If the warning
other one in the passenger-side door. light does not illuminate, if it
remains on or if it illuminates while
driving, contact your Authorized
Ferrari Dealer immediately.

44
 Safety

After deployment, the airbag will be Never modify the airbag modules.
1
� positioned as a protection between the WARNING Do not damage the airbag modules
driver’s or passenger’s head and the (for example pinning something
external structures which could go through
the passenger compartment and cause
onto them or pressing objects
against their covers).
2
injury. The airbags deflate immediately If, for any reason, an airbag cover
afterwards. gets damaged, have the airbag
The side bag activation is not affected by
the front passenger’s height or weight. The
side bag has been designed to activate
module immediately checked by
your Authorized Ferrari Dealer. 3
Activation of a damaged module
whenever the airbag ECU detects a could cause serious or fatal injuries.
collision of a sufficient impact force for
deployment.
Never travel with your head leaning
Please consider that the airbag ECU is 4
not capable of automatically detecting
out of the window, as your head and
damages involving the airbag covers.
WARNING

neck would be in the airbag

Operation
The side bags are controlled by a
activation area. In the event of a side
collision, this position would increase
the risk of being hurled out of the
Do not cover the upper part of the
driver-door and passenger-door panels
with adhesive tape or material and do
5
dedicated ECU that has been designed to
vehicle and would compromise the not treat them in any way.
activate them when a lateral collision of a
protective action of the side bags.
sufficient force occurs.
In the event of a side collision with an
impact force exceeding the limit set by the WARNING
Never place an object over or near
the airbag covers.
Never remove the door panel. If
required, this operation must be
6
ECU, this will transmit a signal for In the event that the airbags are performed by your Authorized Ferrari
activating the pretensioner and the side deployed, these objects would be Dealer.
bag on the impact side. The airbag will
start inflating, opening its cover along the
projected into the passenger
compartment at very high speed. The 7
breakage line, until it is fully deployed (in object will be transformed into a
a few hundredths of a second). projectile propelled in the passenger
compartment. This could cause
serious injuries. 8
45
 Following activation, the airbag Advanced Airbag System
WARNING components can no longer perform �
their protective action; therefore, The system includes:
they cannot be repaired and must be - a 3-point seat belt (lap and shoulder
replaced. After activation of a side seat belt) at each seating position,
bag, have it replaced by your equipped with a pretensioner, an energy
Authorized Ferrari Dealer. management system and a seat belt
The airbag modules must be sensor, which detects when the seat belt
WARNING replaced at the intervals indicated in is fastened (see also page 34)
the “Warranty and Service Book” - a dual stage driver’s airbag at the driver
EVEN if the vehicle was NOT position, located within the steering
involved in a collision. wheel (see also page 41)
- a dual stage passenger’s airbag at the
The label E, on the right-hand side of
front passenger position, located on top
the dashboard, bears the airbag system
of the dashboard (see also page 41)
expiration date. When this expiration
date is approaching, contact your - two remote acceleration sensors, located - a readiness indicator (red warning light
Authorized Ferrari Dealer in order to in the engine compartment A in the instrument panel) (see also
have the system replaced. - a control unit, located on the center page 36) also called “airbag failure
console, in the passenger compartment warning light”
- an Occupant Classification System for
the front passenger, located underneath
the passenger seat, including 4 sensors
and a control unit (see also page 50)

46
 Safety

- a passenger airbag status indicator than a typical one-year old child is

1
(amber warning light B “PASSENGER sitting on the front passenger seat in a
AIRBAG OFF” on the roof panel) (see forward-facing child seat (see also page
also page 39) ��������
�������
50 for more details about Occupant
Classification System)
2
• disable passenger airbag deployment if
nobody is traveling in the front

�
passenger seat or if an object is placed
on top of it. 3
The passenger airbag status can be
monitored by checking the “PASSENGER
AIRBAG OFF” warning light B. This

��������
warning light will be illuminated if
passenger airbag deployment is disabled,
4
������
and will be turned off if passenger airbag
deployment is enabled.

WARNING
Do not carry adults in the front
passenger seat if the “PASSENGER
5
AIRBAG OFF” warning light is
illuminated, as the passenger airbag
- a multi-function display, which will Your system is designed to (see also
temporarily issue a redundant warning
on the passenger airbag status.
page 37):
• disable passenger airbag deployment if a
will not deploy in a frontal crash,
thus reducing the system’s ability to
protect the occupant.
6
child is sitting in a rearward-facing child Do not carry children in rearward-
seat on the front passenger seat facing child seats in the front
7
WARNING

• enable passenger airbag deployment if passenger seat if the “PASSENGER

an adult is sitting on the front passenger AIRBAG OFF” warning light is not
seat illuminated, as the passenger airbag
• either disable or enable passenger could deploy in a frontal crash,

8
airbag deployment if a child heavier seriously injuring or killing the child.

47
The system components are designed to belt sensor to supplement its internal - For crashes of even higher severity, the
work together to help provide the sensing capabilities. The control unit is control unit will deploy the driver airbag
occupant with the most appropriate designed to use this signal to determine in high energy mode and will use the
protection level, based on crash severity whether airbag deployment and signal from the Occupant Classification
and front passenger classification: pretensioner activation are required. System to determine whether to deploy
- The Occupant Classification System will - For frontal crashes, based on the angle the passenger airbag in high energy
attempt, based on the weight resting on and severity of the crash and on the mode or not to deploy the airbag (if the
the seat, to classify the front passenger front passenger classification, the airbag front passenger is classified as child it
either as a child (see also page 50 for control unit is designed to determine will not deploy the airbag. If the front
more details about the Occupant whether to or not to: passenger is classified as “adult” it will
Classification System), for which airbag deploy the airbag).
• deploy the airbags
deployment is not appropriate, as it can
• deploy the airbags in low energy mode If the airbags are deployed, the seat
result in serious injuries and death, or
• deploy the airbags in high energy mode. belt pretensioner will also be activated
an adult (see also page 50 for more
for every seating position where the
details about the Occupant Classification - For low severity crashes, the airbag
seat belt is fastened.
System), for which deployment is control unit will not deploy the airbags.
appropriate depending on the crash The airbag control unit will use the
- For crashes of higher severity, the
severity. seat belt status indicated by the seat
control unit will deploy the driver airbag
belt status sensor in order not to
The classification system will then in low energy mode and will use the
activate the seat belt pretensioner for
transmit the occupant classification to signal from the Occupant Classification
the seating position where the seat belt
the control unit, that will use the System to determine whether to deploy
is not fastened.
information to enable or disable the passenger airbag in low energy
passenger airbag deployment (see also mode or not to deploy the airbag (if the The control unit is also designed to
page 50 for more details about the front passenger is classified as child it perform a check of all the electrical
Occupant Classification System). will not deploy the airbag. If the front components in the system (including a
- In the event of certain frontal crashes, passenger is classified as adult it will self check) upon ignition and periodically
the electronic control unit will use the deploy the airbag) (see also page 50 for thereafter, until the engine is turned off.
signal from the remote acceleration more details about the Occupant
sensors, from the Occupant Classification System).
Classification System and from the seat

48
 Safety

Upon ignition, the “airbag” red warning Never place an object over or near
1
When the “airbag” warning light is
light in the instrument panel illuminates WARNING the driver’s or passenger’s airbags. In
for a few seconds, to confirm the warning illuminated, the system functionality
the event that the airbag is deployed,
light functionality (see page 41).
Whenever the control unit detects a fault
may be compromised or disabled.
Improper repair work on the Advanced
it will project any object over it, or
near it, in the passenger
2
in the system, it will illuminate the “airbag” Airbag System or one of its compartment at very high speed. The
red warning light in the instrument panel, components can render the system object will be transformed into a
inoperative, or cause unintended
to inform the driver that there may be a
system malfunction.
If:
airbag deployment. Work on the
Advanced Airbag System must only be
projectile propelled in the passenger
compartment. This could cause
serious injuries.
3
• the “airbag” warning light does not performed by qualified technicians.
Seat belts are designed to help
illuminate at key on (ignition key in Please contact your Authorized
minimize injury severity in the event
4
WARNING

position II) Ferrari Dealer for repair work on the

of an accident. To help achieve
Advanced Airbag System of your
or optimal protection for adults, the
vehicle.
airbags should supplement the seat
• the “airbag” warning light does not turn
belts. Always wear your seat belts
off a few seconds after key ON
5
Fastening your seat belts is always properly fastened.
or necessary, even with advanced airbags. Front airbags cannot offer protection
• the “airbag” warning light illuminates Front airbags do not substitute the seat WARNING in side crashes, certain front-angular
while the vehicle is in motion belts. The front airbags are designed to crashes, roll over events or in
carefully stop the vehicle in a safe place help increase the efficiency of the seat secondary impacts (if a second crash
and contact your Authorized Ferrari
Dealer immediately.
belts and supplement the protection
offered by the seat belts in medium to
happens after the airbags have been
deployed in a previous crash). The
6
high severity frontal crashes. seat belts are designed to help
The seat belts must be properly worn reduce the risk of injuries in roll
and fastened in order to offer
protection. Refer to page 34 for proper
use of the seat belts.
over events and secondary front
impacts. A properly fastened seat
belt is needed to help protect
7
occupants in roll over events and
secondary front impacts.

8
49
 Front airbags are designed to not be Occupant Classification System NOTE 1
WARNING deployed in low severity frontal
crashes. The seat belts can help The Occupant Classification System is The functionality of the system has been
reduce injuries in low severity designed to (see also page 42): verified by Ferrari for all the following
crashes. A properly fastened seat belt • disable passenger airbag deployment if a child seats:
is needed to help protect occupants child that is lighter and smaller than a Cosco Dream Ride 02-719
in low severity frontal crashes. typical one-year old child (up to 20.1 lbs Britax Handle with Care 191
To help ensure protection in the - 9.1 kg and 26 in. - 66 cm) is traveling in Century Assura 4553
WARNING event of a collision, you must be in a a rearward-facing child seat (see note 1 Century Smart Fit 4543
normal seated position with your on page 50) mounted on the front Cosco Arriva 02727
back against the seat backrest. The passenger seat Evenflo Discovery Adjust Right 212
passenger’s feet must be on the • enable passenger airbag deployment if an Evenflo First Choice 204
footrest. The driver’s left foot must be adult (weighing more than a 103 lbs - Graco Infant 8457
46.7 kg) is sitting on the front passenger Britax Roundabout 161
on the footrest.
seat Britax Expressway
Adjust your seat as far back as Century Encore 4612
WARNING possible, ensuring you can operate • disable or enable passenger airbag Century STE 1000 4416
the vehicle controls properly and deployment if a child heavier than a Cosco Olympian 02803
comfortably. Keep your hands on the typical one-year old child is seated on the Cosco Touriva 02519
steering wheel rim, without crossing front passenger seat Evenflo Horizon V 425
them. Placing your hands or arms Evenflo Medallion 254
inside the rim increases the risk of Safety 1st Comfort Ride 22-400
hand/arm injuries in the event of a
crash with driver’s airbag deployment. The status of the passenger airbag will be
Never place your feet on the indicated by the warning light
WARNING dashboard or the instrument panel or “PASSENGER AIRBAG OFF” on the roof
out of the window, as this will panel:
seriously affect the ability of the • when passenger airbag deployment is
system to protect you in the event of disabled, the “PASSENGER AIRBAG
a crash, and can result in induced OFF” warning light, A, will be
injuries in the event of airbag
illuminated
deployment.

50
 Safety

Installing a child seat with the If the Occupant Classification System

1
WARNING ignition key in position II can result identifies the front passenger as an
in induced injuries. “adult”, passenger airbag deployment will

�
• The extra weight applied on the seat
be enabled and the “PASSENGER
AIRBAG OFF” warning light, A, will not
2
during child seat installation might delay be illuminated.
correct occupant classification if the
child seat is mounted with the ignition The system does not disable the front
key in position II.
After turning the key to ON, the Occupant
passenger seat belt pretensioner (also
known as emergency tensioning
3
Classification System will continuously device).
attempt to classify every object or person The system does not disable the front
on the front passenger seat in one of two
categories: “Child” (for which passenger
airbag deployment is dangerous and must
passenger side bag.
4
When the key is turned to ON, the system
be disabled) or “Adult” (for which will require a few seconds to classify the
• when passenger airbag deployment is passenger airbag deployment is beneficial
enabled, the “PASSENGER AIRBAG
OFF” warning light, A, will NOT be
and must be provided). Occupants or
objects lighter than a typical one-year old
passenger on the front seat. As long as the
system is in the process of classifying the
occupant, the default setting will be child,
5
illuminated. child sitting on a child seat (including an to avoid the risk of injuring a child during
Adults should not travel in the front empty seat) will be classified as “child”. this time.
WARNING passenger seat if the “PASSENGER
AIRBAG OFF” warning light is
illuminated.
Occupants or objects heavier than a
typical one-year old child will be classified
as “adult”.
If the Occupant Classification System
identifies a change in the classification of
6
the front passenger after the vehicle is
Children in a rearward-facing child seat If the Occupant Classification System started (for example, if the driver stops
must not travel in the front passenger identifies the front passenger as a child, without turning off the engine to allow a
7
WARNING

seat if the “PASSENGER AIRBAG OFF” passenger airbag deployment will be front passenger to get in or get out), the
warning light is not illuminated. disabled and the “PASSENGER AIRBAG system will update the passenger airbag
OFF” warning light, A, on the roof panel status and the “PASSENGER AIRBAG
• Install child seats always when the ignition will be illuminated.
key is in position 0 (electrical system off). OFF” warning light status accordingly.

8
51
Please note that the system may take a few 1. An adult transfers part of his/her 11. The seat backrest contacts the rear shelf.
seconds to update the front passenger weight onto other objects other than A button provided on the rear shelf will
classification when the passenger status the seat, e.g.,: move the seat backrest forward.
changes. - by leaning on the armrest 12. The vehicle is used in certain extreme
If the Occupant Classification System - by leaning on the center console driving conditions.
recognizes an internal error, it will signal
- by putting his/her feet on the
the airbag control unit that there may be
dashboard or out of the window
a malfunction, and the control unit will
attempt to: - by leaning on a headrest.
• illuminate the “airbag” red warning light 2. An object is tucked underneath the
seat or behind it. �
on the instrument panel
• disable passenger airbag deployment to 3. An object is tucked between the seat
avoid the risk of injuring a child, lacking and the center console, or between the
a certain occupant classification seat and the door panel.
• illuminate the “PASSENGER AIRBAG 4. An adult is extremely light (less than
OFF” warning light on the roof panel. 102.9 lbs - 46.7 kg).
5. A child has outgrown the weight for
Please note that when the “airbag” which rearward-facing child seats are
warning light is illuminated, there may appropriate.
be an error also in the central control
6. An object is stored behind the
unit, and the system might not be able If the “PASSENGER AIRBAG OFF”
passenger seat and contacts the seat.
to perform as designed. warning light, A, illuminates when an adult
7. Weight is placed on the front
Driving carefully, stop the vehicle in a is seated on the front passenger seat:
passenger seat.
safe place and contact your Authorized • slow down and instruct the front
Ferrari Dealer immediately if the 8. The front passenger seat is tampered
passenger not to lean on the vehicle
“airbag” red warning light on the with.
interiors.
instrument panel illuminates. 9. A child seat contacts the dashboard.
If the “PASSENGER AIRBAG OFF”
10. A child seat is too heavy (see note 1 warning light, A, is still illuminated:
The system’s ability to classify the
on page 50).
occupant in the correct class can be • driving carefully, stop the vehicle in a safe
reduced if: place

52
 Safety

• check for objects tucked underneath the • check for loose objects on the passenger The front passenger’s seat and its
1
seat or behind it floor, either in front or behind the front WARNING control unit are part of the advanced
seat airbag system. Never have your seat
• check for loose objects on the passenger
floor, either in front or behind the front
seat.
• verify that the child has not outgrown
the weight for which rearward-facing
tampered with, as this can result in a
system malfunction, which could
2
child seats are appropriate. If this is the cause serious injuries or death.
If the “PASSENGER AIRBAG OFF”
warning light, A, is still illuminated, call case, install a forward-facing child seat Repairs on the front passenger seat
for assistance.
Do not carry adults in the front
appropriate for the child weight
• if the child has not outgrown the weight
WARNING must only be performed by trained
technicians at an Authorized Ferrari 3
for which rearward-facing child seats are Dealer.
WARNING passenger seat if the “PASSENGER
AIRBAG OFF” warning light is appropriate, try installing a lighter child
seat, if available. When a passenger is sitting in the front
illuminated, as the passenger airbag
will not deploy in a frontal crash,
thus reducing the system’s ability to
If the “PASSENGER AIRBAG OFF”
warning light, A, is still not illuminated:
seat:
• always check that no objects are tucked
4
turn off the engine (key to position 0) underneath the seat or behind it
protect the occupant.
and wait a few seconds. • always check that no objects are
If the “PASSENGER AIRBAG OFF”
warning light, A, does not illuminate when
a child in a rearward-facing child seat is
Restart the engine (see page 102 - 107).
If the “PASSENGER AIRBAG OFF”
loose on the floor, either in front, or
behind the seat 5
warning light, A, is still not illuminated • check that no objects contact the seat
seated on the front passenger seat, drive at
reduced speed. call for assistance. • make sure the “PASSENGER
If the “PASSENGER AIRBAG OFF”
warning light, A, is still not illuminated: WARNING
Do not carry children in rearward-
facing child seats in the front
AIRBAG OFF” warning light status is
appropriate for the type of occupant 6
(ON for a child in a rearward-facing
• driving carefully, stop the vehicle in a passenger seat if the “PASSENGER
child seat, OFF for an adult, either
safe place AIRBAG OFF” warning light is not
ON or OFF for a child properly
• check for contact between the child seat
and the dashboard or other vehicle
illuminated, as the passenger airbag
could deploy in a frontal crash,
causing serious injury or death.
secured in a forward-facing child
restraint system).
7
interiors
• check for objects tucked underneath the Not following the above instructions
can result in serious injuries or death
seat or behind it
8
WARNING

in the event of a crash.

53
ABS If braking with ABS activation occurs,
The ABS system cannot compensate
these adjustment phases will be repeated
This is a safety device which is designed for driving at speeds that are
in cycles until the vehicle comes to a stop
to activate in order to help prevent wheel excessively high for certain traffic or
or the pressure on the pedal decreases.
locking if the driver depresses the brake road surface conditions, worn tires,
In addition, the system offers the worn components in the braking
pedal too sharply, especially under poor
following advantages: system or driving errors.
grip conditions.
- driving stability (no skidding), even in
The system is composed of:
the event of sharp braking approaching The ABS system has been designed for
- an electro-hydraulic unit wheel locking. the sole purpose of assisting the driver in
- an electronic brake-force distributor - maneuverability (no side-skidding on controlling braking under extreme
(EBD) sharp turns). conditions, in which he could instinctively
- four speed sensors on the wheels, This means that even when an emergency cause the wheels to lock.
incorporated in the bearings. situation requires sudden braking, the
These features add to the vehicle’s driver can avoid obstacles, or brake on a CST
standard braking system, without curve, without affecting the vehicle
CST is Ferrari’s acronym for Stability and
changing its characteristics. stability.
Traction Control. The CST is composed of
When the ABS is activated, during The ABS system features remain two main systems:
emergency braking or under poor grip unaltered as long as the speed limit
VDC Vehicle Dynamics Control,
WARNING

conditions, the driver will perceive a for the tire side grip is not exceeded.
performed through the braking
“pulsation” of the brake pedal. Hold the When this limit is exceeded, vehicle
system and engine torque
brake pedal pressed to continue the skidding cannot be avoided.
F1-Trac Traction control, performed
braking action.
- Optimal braking distance: through engine torque
When one of the wheels starts locking, the depending on the type of road surface, modulation, depending on
hydraulic control unit controls the braking the braking distance may be reduced by maximum grip on the road
system by running a 3-phase cycle: as much as 40%. and of secondary systems that are always
- reduction (if necessary) The ABS system does NOT exempt active, such as the ABS, EBD, etc.
- maintenance the driver from driving carefully and
WARNING
To help provide optimal control in different
responsibly at all times. driving and grip conditions, four different
- pressure increase in the hydraulic circuit.
setting levels have been designed:

54
 Safety

- Level 1: helps ensure stability and

1
F1-Trac Tire pressure and temperature
maximizes traction on every type of road
surface, both in low (“Manettino” set to F1-Trac is directly derived from Ferrari’s monitoring system
Low Grip position) and very low
(“Manettino” set to ICE) grip conditions,
expertise in F1 vehicles. This system is
designed to optimize traction by
The vehicle is equipped with a system that
monitors the tire pressure and
2
by means of engine and brake control (in controlling engine power delivery. temperature by means of special sensors
this condition, the standard ASR system F1-Trac is faster and more accurate than secured inside the wheel rims, in position
activates instead of the F1-Trac function).
- Level 2: helps ensure stability and
maximizes traction only in dry- to high-
the traditional control systems, and is
capable of delaying and minimizing
engine torque adjustments, in order to
with the inflation valve. These sensors
transmit a signal that is detected by the
antennas on the car body, behind the
3
grip conditions (“Manettino” set to help ensure the desired trajectory. gravel guards, that are connected to the
SPORT) optimizing engine and brake The system estimates the maximum ECU.
control.
- Level 3: enhances the racing features of
available grip in advance, by continuously
monitoring the relative wheel speed and The system can momentarily 4
using an auto-adaptive operation logic. experience radio-electric interference
the vehicle, helps provide but does not
Comparing this information with the emitted by devices using similar
ensure a good level of stability
frequencies.
(“Manettino” set to RACE) by reducing
engine control to a minimum and making
the best use of brake control.
vehicle dynamics model stored in the
control system, F1-Trac optimizes the
vehicle behavior by controlling engine The ECU processes this information and
5
torque delivery. transmits, via the CAN line, a series of tire
RACE mode must be used only on pressure and temperature data as well as
WARNING race tracks. F1-Trac does not work when the
"Manettino" is set to CST off.
any system errors to the instrument panel.
The signal transmitted by the ECU
6
- Level 4: CST off (position ). activates some symbols on the TFT display,
Stability is not ensured, but all the other with two priority levels: a soft warning
features always present in the other
7
(SW) if the pressure reduction in relation
settings, such as the ABS and EBD, to the rated pressure is greater than 2.9
remain active. When the brake pedal is psi (0.2 bar), and a hard warning (HW) if
depressed, the VDC system reactivates. it is greater than 5.8 psi (0.4 bar) or if
When the brake pedal is relased, the there is a dynamic reduction of over 2.9
VDC system deactivates. psi (0.2 bar/min.)
8
55
The calibration button is positioned on When the display cycle ends, the TIRES
the inside roof panel (see page 94). 1 screen page becomes available again and
the summary symbol for the malfunction
After tire replacement or inflation, the is displayed in the specific area A (screen
system must be calibrated using the page 1), until the malfunction is corrected.
relative button on the roof panel.
� Low pressure
The system warns the driver that the
When the on-board instrument panel
WARNING tire pressure has decreased. However,
receives the signal from the tire pressure
this does NOT exempt the driver
ECU that the pressure level of one tire is
from periodically checking that the
below the alarm threshold, screen page 3
tires are inflated to the indicated The TIRES information page can also be will be displayed
pressure. set as main screen page (see page 83). (regardless of the main screen page set).
In addition, the system is UNABLE to When indication by event occurs (e.g.,
warn the driver of sudden damage to malfunctions with priority levels 1/2, see 3
the tires caused by external objects/ page 86), the page is displayed as in the ����������
agents (e.g., nails, stones, etc.). following example 2 for a time equal to ��������

the entire malfunction display cycle.

Viewing messages on the “TFT” display
By pressing the DISP button or using the
Menu function, the driver can access the 2
TIRES information screen page, which Warning
ice hazard
shows the pressure and temperature
values for each tire, as in the following
example 1. If the tire pressure value of more than one
tire is below the alarm threshold, the
The TFT does not display any warning following screen page 4 will be displayed.
messages related to tire temperature.

56
 Safety

originating the malfunction and therefore Tire punctures

1
� is not capable of indicating the wheel When the on-board instrument panel
involved. In this case, screen page 6 will
2
���������� receives the signal from the tire pressure
�������� be displayed. ECU that the pressure level of one or
more tires is below the alarm threshold,
� screen page 7 is displayed. At the same
time, the warning light on the instrument

3
����������
�������� panel illuminates (see page 93).

7
After the display time has elapsed, the rel- ��������

4
��������
ative screenpage disappears.
Subsequently, if the TIRES screen page is
active, the TFT display will be viewed as
in the following screen page 5.
After the display time has elapsed, the rel-
� ative screenpage disappears.
The TIRES screen page that shows the
5
pressure of each tire cannot be recalled
by the user. The same display logic is applied for the
other priority level 0 malfunctions, until
Also in this case, if the pressure malfunction
persists, upon the next engine starting the
the situation is corrected and the system is
recalibrated (after turning the key to OFF
6
display will show the relative screen page. and then back to ON).
Subsequently the symbol will be viewed in
the area dedicated to the warning lights,

Upon the next engine starting, if the

until the situation is corrected, as is the case
for other priority level 2 malfunctions.
7
failure persists, the relative warning light
will illuminate on the display.
The system may not know which wheel is
8
57
For vehicles equipped with “Run Flat” If, instead, the TIRES screen page is not set up Menu is accessed immediately, as for
tires, screen page 7 will be displayed four as main page, the TFT display will be other priority level 0 malfunctions.
times alternately with screen page 8. viewed as in the following screen page 10. If, instead, during the above mentioned
priority level 2 cycle (RUN-FLAT tire
��
8 puncture, when the speed limit has not
been exceeded and the tire conditions still
permit to travel), the driver presses the
MODE button, screen page 9 will be
displayed. The multi-function symbol will
be displayed in the warning light area, as for
other priority level 2 malfunctions, until the
situation is corrected and the system is
recalibrated.
The instrument panel will calculate the The system may not know which wheel is
Subsequently, the symbol will be residual fuel range and will display the same originating the malfunction and therefore
displayed in the area dedicated to the information after 31 mph (50 km). is not capable of indicating the wheel
warning lights A, until the situation is When a tire is punctured, if you drive more involved. If the TIRES screen page is set
corrected, as is the case for other priority than 62 mi (100 km) screen page 7 will be as the main page, screen page 11 will be
level 2 malfunctions. If the TIRES screen displayed or, if the vehicle speed exceeds 50 displayed.
page is active, the TFT display will be mph (80 km/h) screen page 7 or 8 will be
viewed as in the following screen page 9. displayed, according to the display logic of
��
other priority level 0 malfunctions.
�
After the key has been turned to OFF and
then back to ON, the on-board panel must
display the screen page “System not
calibrated” (see page 59). The TIRES
screen page cannot be recalled by the user.
If, during the display cycle of priority level 0
malfunctions (normal tire puncture), the
driver presses the MODE button, the Set-

58
 Safety

If the TIRES screen page is not set as the If the TIRES screen page is not set as the System not calibrated
1
main page, when the display cycle has main page, when the display cycle has If the system has not been calibrated or
been completed the symbol will be been completed the symbol will be
viewed in the warning light area A
(priority level 2).
viewed in the warning light area A
(priority level 2).
following replacement of one or more
tires, screen page 13 will be displayed.
At the same time, the warning light on the
2
The TIRES screen page that shows the The instrument panel will calculate the instrument panel starts flashing (see page.
pressure of each tire cannot be recalled residual fuel range and will display the same 93). Then the warning light remains on until
by the user.
For vehicles equipped with “Run Flat”
information after 31 mph (50 km).
When a tire is punctured, if you drive more
the system is calibrated.
3
tires, screen page 11 will be viewed four than 62 mi (100 km) screen page 11 will be ��
times, alternating with screen page 12. displayed or, if the vehicle speed exceeds 50 ����
mph (80 km/h) screen page 11 or 12 will
4
��������������

be displayed, according to the display logic

��
of other priority level 0 malfunctions.
Following a key-off / key-on cycle, the on-
board panel must display the screen page
“System not calibrated” (see page 59).
The TIRES screen page cannot be 5
recalled by the user. Subsequently, the screen page reappears
with the “icon” symbol in the area
dedicated to the warning lights (as for
other priority level 2 malfunctions). 6
Subsequently, the symbol will be The system can be calibrated by pressing
displayed in the area dedicated to the the specific button for a time ranging
warning lights A, until the situation is between 4 and 10 seconds (see page 94),
corrected, as is the case for other priority
level 2 malfunctions.
with the key turned to on. When the
button is pressed and the next calibration
7
procedure has been accepted, screen page
14 appears for 5 seconds.

8
59
 Tire pressure monitoring system failure System temporarily not active
��
When one of the following conditions
�� occurs:
- excessively high temperature
- during the calibration
- radio frequencies which disturb the
wheel sensor signal
screen page 16 is displayed.

The TIRES screen page cannot be ��

recalled by the user.
Before calibrating the system, make Screen page 15 is displayed in the
WARNING sure that the tire pressures following cases:
correspond to the indicated pressure - malfunction in the circuit and/or wiring
values (see page 26-27). If this is not leading to the ECU
the case, the system may issue wrong
- signal reception failure by one or more
low pressure indications.
sensors due to malfunctioning, damaged
or flat battery
- ECU malfunctioning. At the same time, the warning light on the
instrument panel starts flashing (see page
At the same time, the warning light on the
93). Then the warning light remains on until
instrument panel starts flashing (see page
the system is calibrated.
93). Then the warning light remains on until
the system is calibrated. Subsequently, the screen page reappears
with the “icon” symbol in the area
The TIRES screen page cannot be
dedicated to the warning lights A (as for
recalled by the user.
other priority level 2 malfunctions).
The TIRES screen page cannot be
recalled by the user.

60
 Safety

System not active

1
After turning the key to ON, if the system

2
was deactivated by means of the
diagnostic tester, screen page 17 will be
displayed. At the same time, the warning
light on the instrument panel starts flashing
(see page 93). Then the warning light
remains on until the system is calibrated.
3
��

4
5
Subsequently, the screen page reappears
with the “icon” symbol in the area
dedicated to the warning lights A (as for
other priority level 2 malfunctions).
6
The TIRES screen page cannot be
recalled by the user.

7
8
61
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
 Overview of controls
Opening and closing
Lighting
Instruments and gauges
Roof panel controls
Controls on the steering wheel
Windshield washer/wipers
and headlight washer
Driving the vehicle
Ignition switch
Handbrake lever
Adjustments
Air conditioning
and heating system
Passenger
compartment accessories
Overview of controls

64
 About your vehicle

1
1 2 �� ��

2
11

10 3
�� 3
9

8
4 5
4
�� �� ��
7 6
5
Ref. Control Page Ref. Control Page
1 Adjustable center air vents 125 10 Air conditioning and heating system controls 122
2
3
Glove compartment
Hazard warning lights control
125
77
11
12
Car radio system
Light switch
-
73 6
4 Glove compartment opening button 126 13 “ENGINE START” button 95
5 Parking sensor control 109 14 “Manettino” control 95
6
7
Controls for door locking and unlocking
Ashtray
68
127
15
16
“TFT” display
Tachometer
79
90 7
8 F1 gearbox Auto button (*) 106 17 Electronic speedometer 90
9 F1 gearbox reverse button (*) 101
(*) Only for “F1” gearbox version
8
65
 ��
��
��

��
�� �� �� ��

�� ��

Ref. Control Page Ref. Control Page

18 External rear-view mirrors adjustment 121 24 Driver-side power window control 72
19 External lights and direction indicators control lever 73, 76 25 Passenger-side power window control 72
20 “DOWN” gearshift lever (*) 97 26 Control for door opening from the inside 69
21 Horn control 97
22 Windshield washer/wipers/headlight washer control 97
lever
23 “UP” gearshift lever (*) 97 (*) Only for “F1” gearbox version

66
 About your vehicle

� ��
2
�
�
�

�
3
�
�

4
5
Ref. Control Page
27 Mechanical gearshift lever 107

7
8
67
Opening and closing Opening from the outside Locking and unlocking the doors from the inside
Using the remote control, deactivate the Press the “LOCK” D button for locking
Doors alarm and the central door locking system, both doors and press the “UNLOCK”
Introduction or turn the key in the lock to deactivate E button to unlock them.
the central door locking system. Always check that the doors are
When a door is opened or closed, the
window automatically moves down by When pulling the handle C to open the WARNING properly closed to prevent them
approximately 2 centimeters, “preset door, the window moves down by from opening while driving.
position” A, in order to avoid damaging approximately 2 centimeters. When the
the “upper weather strip”. When the door is door is closed, it will move back up until
closed, the window automatically moves it meets the weather strip.
back up, position B, until it meets the
“upper weather strip”.

C
A
E

68
 About your vehicle

The lid is held open by two gas struts C.

1
Opening the doors from the inside Engine compartment lid
Pulling the handle F to open the door, the Opening

2
window will lower to the “preset position”.
To open the engine compartment lid, pull
the lever A found beneath the steering C
column.

3
F A

Closing 4
Lower the lid until it is closed and press
down near the lock until you hear it click
in place.
Release the lever B that retains the lid.
This lever is located in the front section of WARNING
Always check that the lid is properly
closed to prevent it from opening
5
the vehicle, in the center position. while driving.
When the door is closed, it will move back
up until it meets the “upper weather strip”.
If the handle F is pulled without opening
6
the door, the window will lower to the
“preset position” but, after 2 seconds, if the
door is not opened, the window will rise
to the “upper weather strip”. 7
Therefore, to open the door, release the
handle F and pull it again. B

8
69
Emergency Opening/Closing Emergency Opening/Closing
If the lid opening lever is not functioning, A If button A and button B on the key
insert your hand through the fins of the remote control are not functioning, lift the
front grill and push until you remove the trim panel (using the tab) of the pocket-
protective cover from its seat. Grip the change tray on the center console, and
ring D with your fingers and pull it pull the ring D of the safety cable.
outwards.

�
Luggage compartment lid
Opening
To open the luggage compartment lid,
Closing
press button A, or button B on the remote Emergency exit from inside the luggage
control, and hold it for more than 2 Using the grip on the inside, lower the
compartment
seconds. luggage compartment lid until it touches
the bodywork. If someone remains closed inside the
The luggage compartment is illuminated luggage compartment accidentally, the
by an internal light that comes on Then press downward on the middle of
luggage compartment lid can be opened
automatically when the luggage the lid until you hear the lock click in
from the inside by pulling the handle E,
compartment lid is opened. place.
located on the back, right-hand side of
the compartment to the right of the lock.

70
 About your vehicle

Closing
1
Screw the cap B back on tightly and close

2
the fuel tank door.
Make sure that the string D is not hanging
out of the fuel tank door.
�
A

B
3
Unscrew the cap B, rotating it
Fuel tank cap and door counterclockwise and hang it on the

WARNING
Always turn off the engine during
refueling. Take extreme care when
hook C.
4
removing the cap.
Do not smoke or use open flames
during refueling.
The following can be harmful for
D 5
your health:
- fuel coming into contact with your
skin
- inhaling fuel vapors.
6
C
Opening
With the key in position 0, press the
release button A to unlock the fuel tank
door.
B 7
8
71
Emergency opening Power windows The driver side is also equipped with
In the event that the button A is button B which operates the passenger-
The power windows can only be used side power window.
malfunctioning, the lid can be opened with the ignition key in position II.
manually by pulling the cable E, located
on the left-hand side of the luggage Passenger-side power window
compartment. Driver-side power window
Press button C to move the window up or
Press button A to move the window up or down.
down. This button allows manual
operation (partial opening/closing) or
automatic operation (complete opening/ C
closing). Press button A briefly, to activate
manual operation. Hold the button down
for a longer time (more than 0.3 seconds)
or press it a second time to activate
automatic operation, so that the window
stops when it reaches the end of its travel.

A B
� Only manual operation is possible (partial
opening) to raise the window: when
button C is released, the window stops at
the position reached. To lower the
window, automatic operation is also
possible (full opening): if the button is
pressed at length (over 0.3 seconds) the
automatic window operation is activated.
The window will only stop when it
reaches the end of its travel or by pressing
the button again.

72
 About your vehicle

When the door is open, the window can Switch A has five positions:
1
Lighting
only rise to the “preset position”, to prevent 0 Lights off
the window from damaging the upper The external lights and the direction
weather strip when the door is closed. indicators only work when the ignition
key is in position II.
Position and license plate lights
on (*) 2
Improper use of the power windows The external lights can be turned on and Low beams on (*)
WARNING can be dangerous. Before use, always off manually or automatically, depending
check that people and objects are at a Parking lights on
safe distance.
Pay particular attention during the
on the ambient light.
AUT Automatic operation of the external
lights according to the ambient
3
Light switch
automatic operation of the driver- light.
side power window. (*) The relative warning light on the
To protect the passengers remaining
in the car against accidental
instrument panel illuminates (see page 93).
High beams
4
operation of the power windows,
always remove the key from the To turn on the high beams, when

5
ignition. switch A is in position , push the left-
hand lever B towards the dashboard.

�
B 6

7
8
73
 Flashing the headlights Parking lights
The headlights can be flashed by pulling The parking lights work only with the
the left-hand lever B towards the steering ignition key in position 0 or with the key
wheel. removed.
They are activated by turning the light
switch A to position .
When the parking lights are on, the relative
warning light illuminates on the
B instrument panel.
When the parking lights are on, move the
left-hand lever B downward to turn on the
� left-hand position lights. Move the lever
upward to turn on the right-hand position
lights.

When the high beams are on, the relative Automatic activation and
warning light illuminates on the deactivation
instrument panel (see page 93).
When the light switch A is turned to AUT
Pull the lever B towards the steering
and the ignition key is in position II, the
wheel again to turn off the high beams
Flashing occurs also with lights off, if the position lights, low beams and license plate
and turn on the low beams.
ignition key is in position II. lights turn on and off according to the
Follow the Road Regulations of the ambient light.
The high beams are used for flashing.
country you are traveling in for using
The high beams can only be activated
the high beams. Follow the Road Regulations of the manually, by pushing the left-hand
country you are traveling in for using lever B toward the dashboard.
the high beams.

74
 About your vehicle

If the high beam control is on, the The driver is always responsible for
1
WARNING high beams will turn on every time WARNING turning on the external lights,
the external lights are activated depending on the ambient light and
automatically. We recommend
therefore that you turn them off
in compliance with the regulations in
force in the country of use. The
2
every time the twilight sensor automatic system for turning on and
deactivates the external lights. off the external lights must be

In case of fog during the day, the

considered an aid for the driver. If
necessary, turn the lights on and off
manually.
3
WARNING position lights and low beams will
not activate automatically. The driver
must always be ready to turn on the Twilight sensor
lights manually, and also the rear fog
lights if necessary.
The twilight sensor is comprised of a
global sensor, which measures the
�
4
ambient light.
When the sensor is faulty, the system will
5
After automatic activation of the external
lights, it will always be possible to turn on turn on the low beams and the position The failure indication will be displayed as
the rear fog lights manually. When the lights regardless of the ambient light. The long as the lights switch A is turned to
external lights are deactivated failure indication will appear on the AUT.
automatically, also the rear fog lights are instrument panel display. In this case, we recommend that you
turned off (if active) automatically.
Therefore, if necessary, the user will have
deactivate the automatic system and turn
on the external lights manually if 6
to turn on the rear fog lights manually necessary.
upon the next automatic activation.
Contact your Authorized Ferrari
Dealer as soon as possible.
7
8
75
Direction indicators Rear fog lights
When lever B is:
- moved up, the right-hand direction
indicators are activated
- moved down, the left-hand direction
indicators are activated.
The relative warning light will
illuminate on the instrument panel.

� E

These can be activated only when the high

or low beams are on, by pressing button D.
The relative warning light E on the
The lever returns to the neutral position instrument panel will illuminate.
automatically when the steering wheel is
straightened.
To indicate a temporary lane change, Use the rear fog lights only in poor
requiring only the slightest turn of the visibility conditions.
steering wheel, it is possible to shift the
lever without clicking it into position
(non-permanent position).

76
 About your vehicle

The dome light activates automatically in

1
Hazard warning lights Dome light
the following conditions:
Press button A to turn on the hazard When the doors are closed, the dome

2
warning lights. All the direction indicators light A on the roof can be turned on or - when a door is opened, for approx.
will start blinking intermittently. These off using the switch B. 3 minutes
lights will operate with the ignition key in Switch C turns on the spot light D. - when all the doors are closed and the
any position. key is in position 0, for approx. 10
seconds
When the lights are on, the relative
warning lights on the instrument panel
and the button will flash.
- when the key is removed, for approx.
10 seconds
3
To turn them off, press the button again. - when the doors are unlocked, for
approx. 10 seconds

A
- when the inertia switch is activated, for
approx. 15 minutes.
4
The dome light deactivates automatically
in the following conditions:

R
- after the preset activation time expires
- when the doors are closed and the key is
5
� in position II
- when the doors are locked
- when the inertia switch is reactivated. 6
�

� �
7
8
77
Instruments and gauges

� � �

120 140 160

100
180
80
� 200
60
220
40
20 0

� � � � � �
Instruments and gauges
1 TFT Display
2 Electronic speedometer
3 Tachometer
4 Gear display
5 Warning lights

78
 About your vehicle

The screen areas A and C are always

1
“TFT” display MODE
present in all display configurations set by Button pressed momentarily (< 2 sec):
Located on the instrument panel, it the driver.
performs the following functions:
- indication of the control parameters
The screen areas B and C can be
displayed with two color options:
- the “complete” MENU page is displayed
if the vehicle speed is below 3 mph –
5 km/h
2
- indication of general information while - day (white background)
driving - the “minimized” MENU page is
displayed if the vehicle speed exceeds
3
- night (black background).
- fault warnings. 3 mph – 5 km/h
The screen area A can be displayed with
The driver can interact with the system by five different color options, based on the - within a submenu: back to last page
choosing graphic configurations and driving modes set through the displayed
setting the parameters. “Manettino”. - odometer flashing: back to previous
Three different screen areas are available,
depending upon the display type chosen:
information
- exits the display of the various check
4
A display of information shared by all A
phases when the key is turned to ON
configurations (with the exception of
- the malfunctions are iconized if the
the driving mode symbol)
B display of virtual control gauges and of
information generated by specific
B
button is pressed during fault warnings.
5
events and/or on request
C permanent display of information
6
C
(shared by all configurations).

The screen page is activated and set by

pressing the buttons DISP and MODE on
the control panel, to the right of the
steering wheel, and by pressing the 7
buttons UP, DOWN and ENTER located
behind the steering wheel.

8
79
Button pressed at length (> 2 sec): UP/DOWN - confirms the setting/change
- MENU page not active and TRIP B - Sets/adjusts the functions in the MENU - stores the changes confirmed
disabled: resets TRIP A page - TRIP A is reset, when TRIP B is
- MENU page not active and TRIP B - MENU page not active: adjusts the enabled, only after pressing the MODE
enabled: selects the odometer displayed instrument panel brightness level button at length (TRIP A flashes).
(flashing) (either tot, A or B) - odometer flashing: selects the TRIP to
- MENU page active: back to last page reset Configurations:
displayed before MODE button was - Auto function (twilight sensor active): The display B can have the following
pressed. adjusts the sensor’s sensing range. configurations, which are selected using
the DISP button (the screen page recalled
DISP (DISPLAY) is active for ten seconds), or from the
Scrolls through the following screen MENU page, using the MODE button
pages: (the screen page recalled remains
- SPORT displayed as the main screen page):
- RACE - SPORT
- TRIP A - RACE
- TRIP B - TRIP A
- TIRES - TRIP B
- TIRES

ENTER
- MENU page not active: switches
between the information displayed:
- total odometer
- TRIP A
- TRIP B (if enabled)
- confirms the selected function

80
 About your vehicle

SPORT screen page RACE screen page

1
In addition to the shared parameters, the RACE mode must be used only on

2
screen page shows the virtual control WARNING race tracks.
gauges, for:
- water temperature In addition to the shared parameters, the
screen page shows:
- oil temperature.
- the virtual water and oil temperature
gauges (minimized)
- Current Lap
3
- Best Lap
In case of malfunctions/events which - Last Lap
need to be displayed through a multi-
function symbol, this will be viewed, at
- Max-Speed Best
- Max-Speed Last.
4
the end of the display cycle, in one of the
three dedicated sections of area B.

When the SPORT screen page is

5
displayed and an event occurs that needs
to be viewed, the display will appear as in
the following example.
6
When the virtual control gauges are mini-
mized, they are displayed as symbols.
They only use black symbols on a back-
7
ground which can have different colors
(i.e., blue, green, red) according to the
temperature range.
8
81
Oil temperature gauge: When the RACE screen page is displayed, - the date
- Blue = < 131 °F (55 °C) the functions of some buttons change. - the trip distance
- Green = 131 °F (55 °C) - 311 °F (155 °C) The ENTER button is used to start the - the average speed
- Red = > 311 °F (155 °C). chronometer:
- the cruising range
Water temperature gauge: - when the chronometer is off, press the
- the trip time.
button to activate the Current Lap
- Blue = < 158 °F (70 °C)
chronometer
- Green = 158 °F (70 °C) - 257 °F (125 °C)
- when the chronometer is on, press the
- Red = > 257 °F (125 °C).
button to reset and restart the Current
When the RACE screen page is displayed Lap and update the information about
and an event occurs that needs to be the previous laps. �����

viewed, the display will appear as in the The DISP button:

following example. - stops the chronometer and updates the
information on the previous laps (button
pressed briefly)
- resets the chronometer and updates the
information about the previous laps If the driver selects TRIP B as main
(button pressed briefly). screen page and then deselects TRIP B
The RACE screen page cannot be from the Menu page, the default screen
selected from the MENU page when the page will be automatically set as main
following driving modes are active: page.
SPORT, LOW GRIP and ICE. When the TRIP A or B screen page is dis-
played and an event occurs that needs to
During display of the event/malfunction , TRIP A and B screen page be viewed, the display will appear as in
the chronometer remains active and is In addition to the shared parameters, the the following example.
viewed again at the end of the display screen page shows:
cycle. In the event of priority level 0 - the virtual water and oil temperature
malfunctions (see “TFT display warning gauges (minimized)
lights”) the chronometer is deactivated.

82
 About your vehicle

1
Parameters shared by all
configurations:

1 C
2
Odometer
The odometer is always viewed on the
TFT display (in area C: by pressing the
3
ENTER button, the user can select
In case of malfunctions/events which When the TIRES screen page is displayed whether to view the total odometer 1 or

4
need to be displayed through a multi- and an event occurs that needs to be one of the two trip odometers 2.
function symbol, they will be viewed, at viewed, the display will appear as in the �

the end of the display cycle, in one of the following example. � �

three dedicated sections of area B.
To reset the trip odometers, press and
TIRES screen page
In addition to the shared parameters, the
hold the MODE button. If TRIP B is not
enabled, TRIP A is automatically reset,
5
screen page shows: whereas if it is enabled, the active
odometer flashes. Use the UP and DOWN
- the virtual water and oil temperature
gauges (minimized)
- the vehicle symbol with the pressure
buttons to select the desired TRIP, and
press ENTER to reset the flashing
odometer.
6
and temperature values for each tire
When the odometer is flashing, to return
- the multi-function symbol for to the previous screen page press the
malfunctions (if any).
For further information, please see the
“Tire Pressure and Temperature
MODE button momentarily or wait 10
seconds.
7
Monitoring System” in the “Safety”
section.
8
83
Fuel level gauge Driving mode symbol The parameters that may be set are:
The information is permanently displayed The information is permanently displayed - Brightness
in area C. in area A. - Display setting
Configuration settings: - Date and time
Speedometer
Menu Page - Language and units of measurement
The information is displayed in area C.
- Vehicle setting
If the speedometer display is disabled, the
- Service.
outside temperature will be viewed in its
place. To select the above mentioned parameters
and the related functions, use the UP and
DOWN buttons.
Clock
To confirm the selected parameter, press
ENTER.
A

Lighting
The clock is always displayed in area A, in
The day-time or night-time mode are set
all configurations, and can be viewed in
To display the MENU page, press the depending upon activation of the position
the “24h” or “12h – AM/PM” format.
MODE button momentarily. lights. However, if the twilight sensor
detects sufficient light, it may not switch
Outside temperature gauge to the night-time mode. Both options have
The information is displayed in area A, if eight brightness levels which can be set
the speedometer display (area C) is using the UP and DOWN buttons. To
enabled. confirm the selected parameter, press
The information is displayed in area C, if ENTER.
the speedometer display is disabled. In To adjust the brightness level, you can use
this case, the word “Manettino” will be the UP and DOWN buttons without
displayed in area A. accessing the MENU page.

84
 About your vehicle

Display setting The units of measurement options are: To select the parameters, press the UP
1
In this area the user can choose the - distance (km or miles) and DOWN buttons. To confirm the
selected parameter, press ENTER.
2
configuration that will be permanently - temperature (°C or °F)
displayed. The following options are
- pressure (bar or psi). Service
available: SPORT, RACE, TIRES, TRIP
A and TRIP B. The RACE screen page is To select the parameters, press the UP Select Service to view the
not available when the “Manettino” is set and DOWN buttons. To confirm the MAINTENANCE SCHEDULE (see
to SPORT, LOW GRIP or ICE. selected parameter, press ENTER. “Warranty and Service Book”).
3
Date and time Vehicle setting Displayed information upon key-on
The date may be displayed in two The parameters that can be changed are: When the key is turned to ON, the check
formats: day/month/year or month/day/
year. Press the UP and DOWN buttons to
select the desired format and adjust the
- Park. sensor*
- Door locking
procedure is started and the word
“Check” will be displayed in area B, on a 4
pale blue background. The main screen
date. Press ENTER to confirm. - Door unlocking
pages that normally display the virtual
The time may be displayed in the “24h” - Speed limit buzzer water and oil temperature gauges
or “12h – AM/PM” format. To select
the format and adjust it, use the UP and
- Buzzer volume
- Light sensor
(minimized) will not be viewed during
the check stage.
5
DOWN buttons and confirm with
- Glove compartment button
ENTER.

Language and units of measurement

- RPM rep. on the steering wheel
- Equalizer. 6
The language options available are:
- English * if the vehicle is equipped with optional
- German
- Italian
parking sensors
7
- French
- Spanish.
8
85
Once the check procedure is successfully TFT display warning lights Battery conditioner connected
completed, the word “Check” will be Priority level 0 (Extremely critical When the instrument panel is on, it
replaced by “Check OK” on a green malfunction): remains displayed for an indicates that the connection with
background. unlimited period of time, until the the battery conditioner is active
When the engine is started, regardless of problem is corrected. (priority level 0).
the main screen page set, the words Priority level 1/Priority level 2 (Critical
“ENGINE ON” will be displayed. malfunction/Non-critical malfunction): Inertia switch
remains displayed for 20 seconds in the Indicates activation of the inertia
center of area B and is then minimized. It switch following an accident and the
remains displayed (minimized) at the resulting cut-off of the fuel supply
bottom left of area B, until the problem (priority level 0).
is corrected.
Alternator
Alarm system failure Indicates an alternator failure
Indicates a fault in the alarm system (priority level 1).
(priority level 1).
Low windshield washer fluid level
The system is not programmed
(priority level 2). Indicates a low level of washer fluid
in the windshield washer tank
It may be associated with messages.
(priority level 2).
Contact your Authorized Ferrari
Dealer.

Fuel reserve
Indicates that the fuel level is low
(priority level 2).

86
 About your vehicle

Oil temperature On-board diagnostic system (OBD) Stop lights failure

1
Indicates that the oil temperature is Indicates a malfunction or failure of Indicates a system failure or

2
too high (priority level 0). the Ignition/Injection System burning-out of the STOP light bulb
and/or the Emission Control System (priority level 2).
(priority level 0).
Turn off the engine and contact Seat heating
your Authorized Ferrari Dealer. Generic failure Indicates that the seat heating
Indicates a generic failure (priority
level 0). A failure message is
function is active (front RH/LH).
(Remains displayed for 5 seconds) 3
associated with the warning light.
Oil pressure
Indicates that the oil pressure is too Lights failure
low (priority level 0). Indicates a system failure or
burning-out of the light bulbs in the
4
position, direction indicators or rear
Turn off the engine and contact fog lights (priority level 2).
your Authorized Ferrari Dealer.
Number plate lights failure 5
Engine coolant temperature Indicates a system failure or
burning-out of the license plate light
Indicates that the engine coolant
bulb (priority level 2).
temperature is too high (priority
level 0). Twilight sensor failure
6
Turn off the engine and contact Indicates a twilight sensor failure
your Authorized Ferrari Dealer. (priority level 2).

7
8
87
 Catalytic converter temperature Power steering failure ABS
If flashing, it indicates that the Indicates that the power steering Indicates an ABS system failure
catalytic converter temperature is system is inefficient (priority (priority level 1).
too high: slow down until the level 2).
warning light goes off (priority level The standard braking system is
1). A failure message is associated Contact your Authorized Ferrari still functioning.
with the warning light. Dealer. Contact your Authorized Ferrari
If the warning light remains on Dealer.
without flashing, the catalytic Fuel tank door open
converter temperature is excessively Indicates that the fuel tank door is EBD
high; stop the vehicle (priority level open (acoustic signal when the Indicates an EBD system failure.
0) and turn off the engine so the vehicle is moving). (priority level 0).
exhaust system can cool down (see
pag. 156). After about five minutes, Low F1 gearbox oil level It is displayed together with the
start the engine again and drive ABS warning light.
The red symbol indicates that the
normally. A failure message is Stop the vehicle avoiding hard
F1 gearbox oil level is too low
associated with the warning light. braking. Drive at low speed
(priority level 0). WARNING

(max. 25 mph - 40 km/h) to

Indicates a failure of the catalytic Contact your Authorized Ferrari leave the road. Do not drive
converter temperature sensor Dealer. further and contact an
(priority level 0). A failure message Authorized Ferrari Dealer
is associated with the warning light. immediately.
Doors or front/rear lids open
Indicates that the doors or front/
rear lids are open or improperly ASR + CST on
closed. The part concerned is
Indicates that the ASR and CST
highlighted in red (acoustic signal
systems are active (priority level 1).
when the vehicle is moving).
A failure message is associated with
the warning light.

88
 About your vehicle

ASR + CST off ASR/CST system activation Brake malfunction

1
Indicates that the ASR and CST Indicates that the CST system has Indicates that the brake fluid is low

2
systems are deactivated (priority activated (priority level 1). or that there is an EBD failure
level 1). This is displayed together A failure message is associated with (priority level 0).
with the words CST off. the warning light.
A failure message is associated with Tire pressure Rain sensor failure
the warning light. Warning light connected with the Indicates a rain sensor failure
ASR/CST failure
Indicates an ASR/CST system
tire pressure monitoring system
(priority level 0 or 2).
Airbag system failure
(priority level 2).
3
failure (priority level 1). Suspension control system failure
A failure message is associated with Indicates a system failure (priority Indicates a malfunction in the
level 0). At the same time, the suspension control system (priority
4
the warning light.
Stop the vehicle avoiding hard Airbag warning light remains on. level 2).
braking. Drive at low speed
WARNING

Contact your Authorized Ferrari

(max. 25 mph - 40 km/h) to
Dealer.
leave the road. Do not drive Contact your Authorized Ferrari
further and contact an
Authorized Ferrari Dealer
Indicates that the Airbag test cycle
has not been completed. At the
Dealer.
5
immediately. same time, the Airbag warning light "Manettino" failure
flashes (priority level 0). Indicates a "Manettino" failure
CCM brake discs worn
Indicates that the carbon ceramic
discs are worn (priority level 2).
Speed limit exceeded (km/h)
Indicates that the speed limit set by
(priority level 1). A failure message
is associated with the warning light.
6
the user has been exceeded (priority
Contact your Authorized Ferrari level 2). Parking sensor failure

7
Dealer to have the brake pads Driver-side seat belt not fastened Indicates that the parking sensor
replaced. Indicates that the driver-side seat system is faulty (for vehicles
belt is not fastened equipped with this system) (priority
(priority level 0). level 2).

8
89
 Ice hazard Radio system information Electronic speedometer
Indicates that the outside See the “Quick reference” guide for Indicates the vehicle speed.
temperature is 38 °F (3 °C) or lower, the car radio system.
indicating the risk of icy road
surfaces. CD-Changer information
Drive carefully and slow down as See the “Quick reference” guide for
the grip of the tires could be the car radio system.
markedly reduced. ��� ���
CD, MP3 CD information ���
In this condition, do not ���
activate “SPORT” or "RACE"
WARNING See the “Quick reference” guide for ���
mode. the car radio system. ��
F1 gearbox failure ���
Flashcard information
��
Indicates an F1 system failure
(priority level 1). See the “Quick reference” guide for
���
��
the car radio system.
Contact your Authorized Ferrari �� �
Dealer. Telephone
See the “Quick reference” guide for
Scheduled maintenance the car radio system.
Depending on the associated If the external temperature is not
message, this indicates that service displayed, the speed will also be shown
schedule deadlines are either on the TFT display.
approaching or due.

Contact your Authorized Ferrari

Dealer upon reaching this
deadline.

90
 About your vehicle

1
Tachometer Gear display (F1) Warning lights
Indicates the engine RPM. Avoid engine It is incorporated in the tachometer. With In addition to the self-check performed
speeds in the red sector. the ignition key in position II, it displays
the gear engaged.
before ignition, the warning lights may
illuminate in the following cases: 2
N Neutral (x) associated with a specific TFT display
R Reverse warning light
1
2
1st gear
2nd gear
If a warning light indicating a failure
illuminates while driving, contact your 3
Authorized Ferrari Dealer to have the
3 3rd gear
necessary checks performed.
4 4th gear
5
6
5th gear
6th gear
ABS (x)
While driving, it illuminates to
4
Auto Automatic gearshift mode indicate a failure in the ABS system.

Auto▼ Easy exit mode

When the symbol “_” is displayed, it

The standard braking system is
still functioning. 5
indicates a fault in the gearbox. Contact your Authorized Ferrari
Dealer.
Please contact your Authorized
If such speed rates are exceeded, the
ignition/injection ECU will temporarily
cut-off the fuel supply.
Ferrari Dealer to have the necessary
checks performed. Brake failure (x)
6
Indicates that the brake fluid level
in the tank is too low.

WARNING
Stop the vehicle avoiding hard
braking. Do not drive further,
7
check the fluid level in the tank
and immediately contact your
Authorized Ferrari Dealer.
8
91
 ASR/CST failure (x) Parking brake Oil temperature (x)
Indicates an ASR/CST system When the handbrake is applied. Indicates that the engine oil
failure. temperature is too high.
Stop the vehicle avoiding hard Alternator failure (x)
If the charging system is faulty. Turn off the engine immediately
WARNING braking. Do not drive further
and contact your Authorized
and immediately contact your When the battery is insufficiently Ferrari Dealer.
Authorized Ferrari Dealer. charged or overcharged (flashing).
The vehicle can still be driven Indicates that the specific sensor is
WARNING at low speed (max. 25 mph – Brake pad wear (x) faulty.
40 km/h), to leave the road. Indicates that the brake pads are
worn. Engine coolant temperature (x)
Indicates that the engine coolant
Contact your Authorized Ferrari temperature is too high.
Failure of all the braking systems “ABS – Dealer to have the brake pads
EBD – CST” (x) replaced. Turn off the engine immediately
When the three warning lights and contact your Authorized
illuminate simultaneously. Oil pressure (x) Ferrari Dealer.
Indicates that the engine oil
Danger of rear wheels locking pressure is too low. Airbag system failure (x)
WARNING and risk of spinning. While driving, it indicates a
Stop the vehicle avoiding hard Turn off the engine immediately malfunction in the airbag system
braking. Do not drive further and contact your Authorized and/or in the seat belt
and immediately contact your Ferrari Dealer. pretensioners.
Authorized Ferrari Dealer.
Indicates that the specific sensor is If the warning light does not
faulty. illuminate for the self-check cycle
The vehicle can still be driven or if it illuminates on while
WARNING at low speed (max. 25 mph – driving, contact your Authorized
40 km/h), to leave the road. Ferrari Dealer immediately.

92
 About your vehicle

F1 gearbox failure (x) Fuel reserve (x) Alarm system failure (x)
1
- Warning light permanently on Indicates that only 20 liters of fuel While driving, it illuminates to

2
accompanied by an acoustic alarm: are left in the tank or that the level indicate a failure in the alarm
when an operating error occurs in gauge is malfunctioning. system.
the F1 gearbox.
Direction indicator Contact your Authorized Ferrari
If the failure still permits it, leave When the direction indicators are Dealer.
the road and contact your
Authorized Ferrari Dealer.
activated.
When the hazard lights are turned ASR + CST off (x)
3
- Flashing: low system pressure. on. Indicates that the ASR and CST
systems are deactivated.

4
Seat belt (x) Position lights
When the ignition key is in When the position lights or low Tire pressure and temperature monitoring
position II, it indicates that the beams are turned on. system
driver’s seat belt is not fastened. Warning light connected with the tire
High beams pressure and temperature monitoring
On-board diagnostic system (OBD) (x)
It indicates a malfunction in the
When the high beams are turned on.
When the high beams are used to
system (on page 56). 5
emission control system and/or flash.
ignition/injection system.
After turning the ignition key to
position II, this remains on for a self
Parking lights
When the parking light control
6
check for eighteen seconds button is pressed.
following engine starting.

7
Rear fog lights
When the rear fog lights are turned
on.

8
93
Roof panel controls Deactivating the anti-lift alarm The system will take a maximum of
system 20 minutes to complete the calibration
Deactivating the alarm system procedure with the vehicle in motion.
motion sensors Pressing button B deactivates the anti-lift
For further information, please see the
alarm system.
Pressing button A deactivates the motion “Tire pressure and temperature
When this feature is deactivated, the LED monitoring system” (on page 55).
sensing feature of the alarm system. above the button flashes for about 3
When this feature is deactivated, the LED seconds and then turns off.
above the button flashes for about 3
seconds and then turns off. Tire pressure calibration button
To calibrate the system, when the key is
in position II, press button C until the
message “calibration activated” appears on
the TFT display.
� � �

�����������
���������

94
 About your vehicle

1
Controls on the steering wheel Driving mode selection switch LOW GRIP mode
The driving mode selected does not This mode can be activated when driving
Start button
2
exempt the driver from complying with comfort is required, even for sports-style
Press the ENGINE START button A to the rules of safe driving. driving, to help ensure stability in low and
start the engine. When the engine has medium grip conditions. This mode is
The driver can select the driving mode recommended also for city driving.
started, release the ENGINE START using the “Manettino” B, according to the
button. Activation will be indicated by the Low
Do not hold the ENGINE START button
down for a long time.
desired driving style.

In the event of a failure of one of the

Grip symbol in the dedicated area of the
TFT display. 3
For the starting procedure, see “Starting onboard systems, indicated by the
°F

and driving the vehicle” on page 100. warning light on the instrument panel
display (see page 89), the system
moves to a “recovery” mode, allowing
the vehicle to still be driven. In these For use, see on page 115.
4
cases, contact your Authorized Ferrari
Dealer. SPORT mode

� ICE mode
This is the ideal setting for vehicle
performance.
5
� This mode can be used when the road Select SPORT mode for sports-style
conditions are particularly slippery (e.g., driving, under high-grip conditions.
snow, ice).
Activation will be indicated by the ICE
Activation will be indicated by the
SPORT symbol in the indicated area on
6
symbol in the dedicated area on the TFT the TFT display.
display.

00:20 AM
000 °F
����� AM
��� °F
7
For use, see on page 115.
For use, see on page 115.
8
95
RACE mode
RACE mode must be used only on In addition, CST deactivation will cause
WARNING race tracks. the RACE and CST symbol to be
displayed in the dedicated area on the
RACE mode is designed to further TFT display. A
enhance the racing style performance of An acoustic signal will warn the driver that
the vehicle. Activation will be indicated by the driving mode has been changed.
the RACE symbol in the dedicated area When the CST feature is active, the
on the TFT display. warning light A starts flashing on the
This mode is ideal for using the vehicle instrument panel, and the relative warning
on the race track. light on the TFT display illuminates
accompanied by the message “ASR/CST
°F
active”.

In low- to medium-grip conditions (e.g.,

wet, icy, sandy roads), do not deactivate
For use, see on page 116. the CST system.
Contact an Authorized Ferrari Dealer.
Deactivating the CST system ( CST ) When the CST system is active and the
Select this mode to deactivate the CST amber warning light comes on, it means Every time the engine is then started,
system (always active when the engine is that there is a fault in one of the CST the CST system will reactivate.
started). system components.
The CST system reactivates
00:20 AM
000 °F automatically, even in CST mode, when
the brake pedal is depressed.
Deactivation of this mode will be When the brake pedal is released the
indicated by the warning light A on the VDC system deactivates.
instrument panel and by the ASR/CST
failure warning light with the message For use, see on page 116.
“CST off ” appearing on the TFT display
for 5 seconds.

96
 About your vehicle

1
Horn control “UP” gearshift lever Windshield washer/wipers and
Press the upper sides of the steering (vehicles with F1 gearbox) headlight washer
wheel rim, in position with the horn
symbol, to activate the horn.
Pull the right-hand UP lever towards the
steering wheel to shift gears up. Windshield wipers 2
For use, see “Starting and driving the
vehicle” (F1) on page 100. The windshield wipers and washer
work only with the ignition key in

���� ��
position II.
3
The lever A has 5 settings:
OFF Windshield wipers stationary.
AUTO Automatic operation. In this
position, the rain sensor’s sensing
4
range can be adjusted (lever
pushed down to first click).
1 Slow continuous operation (lever
pushed down to second click. 5
“DOWN” gearshift lever 2 Fast continuous operation (lever
(vehicles with F1 gearbox) pushed down to third click).
Pull the left-hand DOWN lever towards
the steering wheel to shift gears down.
Lever Fast temporary operation
up (automatic return). 6
For use, see “Starting and driving the
vehicle” (F1) on page 100. Windshield washer
This is activated by pulling lever A towards
the steering wheel (automatic return).
7
When the windshield washer is activated,
the windshield wiper starts automatically.
8
97
 Headlight washer (optional) Rain sensor
The headlight washer is activated The rain sensor automatically adjusts the
automatically when the windshield washer windshield wiper timing to the intensity
is operated and the low beams are on. of the rain during intermittent operation.
The headlight washer and windshield All functions controlled by the right-hand
A washer share the same fluid tank, and a lever are unaffected.
low fluid level is indicated by the relative The rain sensor automatically activates
warning light on the TFT display. when the right-hand lever is moved to
OFF
A UT O AUTO, and it has a range of adjustment
which runs from “wiper stationary” (when
the windshield is dry) to “fast continuous
operation” (with heavy rain).
To regulate the frequency of intermittent
operation, with the lever at AUTO, turn
the control C.
Releasing the lever stops the jet of fluid
while the blades continue to wipe for a
short time. C
Do not operate the windshield
WARNING washer during the cold months until
the windshield has warmed up. If it
has not warmed up, the liquid could
freeze on the glass and block the OFF
view. A UT O

98
 About your vehicle

Turning the control clockwise,

1
Rain sensor failure Driving the vehicle
intermittent operation varies from a In the event of a malfunction occurring
maximum (fast intermittent operation) to Running-in
2
when the rain sensor is active, the wipers
a minimum (slow intermittent operation). will be set to intermittent operation and The latest manufacturing techniques have
the sensing range will be set by the driver, allowed us to achieve high precision and
The rain sensor function is reset by whether there is rain on the windshield or
turning the ignition key to position 0, accuracy levels in the construction and
not. In this case, we recommend that you assembly of components. Nonetheless, the
3
and also by leaving the right-hand deactivate the rain sensor and turn on the
lever in position AUTO. To reactivate vehicle’s moving parts need to be run-in,
wipers, if necessary, in continuous mode. especially in the first hours of driving the
it, turn the control to OFF and then
again to AUTO. vehicle.
Contact your Authorized Ferrari
Dealer as soon as possible.
WARNING
Before cleaning the front windshield
(for example in service stations)
make sure the rain sensor is
Engine and transmission
Avoid exceeding 5000 RPM for the first 4
620 mi. (1000 km).
deactivated or that the key is at
position 0. The rain sensor must be After starting, do not exceed 4000 RPM
deactivated also when washing the
vehicle by hand or in automatic car
until the engine has warmed up (oil
temperature: 149/158 °F – 65/70 °C). 5
washes. Do not let the engine run at a constantly
In case of ice or snow on the front high speed for a prolonged time.
windshield, do not activate the rain
sensor to avoid damaging the wiper
motor and/or blades.
6

7
8
99
 BEFORE YOU DRIVE Recommended lubricants and fluids Starting and driving the vehicle
WARNING
Check that the seat belts are fastened. (F1 gearbox)
Check that the doors are closed. Use unleaded fuel only!
System starting
Check that the seat is properly
WARNING
Using leaded fuel would
When the ignition key is turned to posi-
adjusted. permanently damage the catalytic
tion II the gear display and all its seg-
converters.
Check the rear-view mirror adjustment ments, as well as the relative failure warn-
(center and sides). ing light illuminate. The warning light will
To help ensure optimum engine operation turn off if no problems are detected with-
Before a trip and the best vehicle performance, use in a few seconds.
Preliminary checks “Premium Gasoline” with an octane level The gear currently engaged will remain
of 91-94 A.K.I.. highlighted on the display.
Check the following at regular intervals
and always before long trips: For specifications and quantities of lubri-
cants and fluids, follow the information
- tire pressure and condition reported in the “Recommended lubricants
- levels of fluids and lubricants and fluids” table on page 30.
- condition of the windshield wiper blades
- proper functioning of the warning lights
and external lights.

In any case, it is advisable to perform

these checks at least every 620 mi.
(1000 km), and to always comply with
the maintenance schedule.

It is also advisable to:

- clean the glass covers of the external
lights and all the glass surfaces
- properly adjust the mirrors, steering
wheel, seats and seat belts.

100
 About your vehicle

Operation with the engine off When the engine is off, 1st gear, reverse
1
When the driver-side door is opened,
gear R and neutral N can be engaged.
the system pump may activate for The default setting for the F1 gearbox Holding the brake pedal depressed
several seconds. This function allows
the system to be ready for operation
when the ignition key is inserted.
is always “AUTO” mode.
Every time the vehicle is started, the
during the request, proceed as follows:
N: pull both the levers located behind the
2
F1 gearbox is in “AUTO easy exit” steering wheel.
The failure warning light may also mode, unless the gearbox was in

3
flash for a short time (10 sec.) and “AUTO” mode when the engine was
then turn off: the system completes the turned off (see page 106).
“start-up” phase and will then start ���� ��
To exit “AUTO easy exit” mode,
functioning normally. Avoid entering
operate one of the levers UP and
any commands in the system during
DOWN (when the vehicle is moving)
this stage.

If the failure warning light continues

or press the AUTO button on the
center console.
4
WARNING flashing without going off, deactivate
the system and restart it. If the Once the “System start-up” phase has
failure persists, contact an
Authorized Ferrari Dealer to have
been completed, the gear engaged will
appear on the display: R: press button R on the center console. 5
the necessary checks performed. N (Neutral) 1st gear: pull the UP lever towards the
R (Reverse gear) steering wheel.
If the warning light remains on, it means
that there is a system failure. This
condition will also be indicated by an
1 (1st gear)
2 (2nd gear), etc. � 6
acoustic alarm when the ignition key is If the indication flashes (this may also R
turned to position II. occur in N), the gear is not properly
Contact your Authorized Ferrari
Dealer to have the malfunction
engaged or disengaged. Request N and
then the desired gear.
If a horizontal dash appears on the
7
identified and corrected.
display, there is a system failure.
WARNING

8
101
 Hold button R down, until the letter Starting and warming up the engine
WARNING R appears on the display. (F1 gearbox)
Release the UP and DOWN levers and - Ensure that the handbrake is engaged
the button R soon after the gear and that the doors are closed.
engaged is shown on the display. - It is advisable to keep the brake pedal
Continued operation may activate the pressed when starting the engine.
failure warning light (see page 92) and
- Do not push the accelerator pedal.
the acoustic alarm.
- Turn the ignition key to position II and
Do not operate the system with the
wait until the words Check OK are
engine off, to prevent discharging the
viewed on the TFT display. If the words
battery. - After the engine has started, the words
Check OK do not appear, turn the key
ENGINE ON will be displayed.
back to position 0, wait a few seconds
Also avoid unnecessary gearshifting and repeat the procedure. Do not hold the ENGINE START button
when the engine is off, in order to down for a long time.
- The vehicle is always started in “AUTO
prevent the system pump from easy exit” mode, unless it was turned off If the engine does not start, turn the key
overheating. with the gearbox in “AUTO” mode. back to position 0 and wait until the gear
If the engine compartment lid is open display turns off before repeating the
- Press the ENGINE START button and
or not properly closed, none of the procedure.
release it as soon as the engine starts. Do
gears can be engaged. not hold the ENGINE START button Hold the brake pedal down while
When the vehicle is stationary, with the down for a long time. WARNING starting the engine.
driver-side door open or not properly
closed and the brake pedal released,
the system disengages the gear
engaged after approximately two
seconds.

102
 About your vehicle

If the engine fails to start after several

1
Driving the vehicle (F1 gearbox) When reverse gear is engaged, an
attempts, check for one of the following
With the engine started, the vehicle acoustic safety signal beeps
causes:
- insufficient speed of the starter motor
(dead battery)
stationary and the brake pedal pushed,
pull the right-hand UP lever towards the
steering wheel to engage 1st gear.
intermittently for the entire time that R
remains engaged. 2
- ignition device faulty If the system automatically engages 2nd
Use 1st gear for parking or for
gear when shifting from R to 1st gear,
3
- electrical contacts faulty WARNING starting uphill.
- fuel pump fuses blown. jamming has occurred on 1st gear.
Release the brake pedal and press the Therefore, this is not a malfunction, as it
accelerator to start off. falls within the system operation logic.
Do not run the engine at high speeds For the same reason, when shifting from
As soon as a gearshift is requested (with

4
until the engine oil temperature has 1st gear to R, the system will
the vehicle in motion) using the levers UP
reached at least 149–158 °F (65÷70 °C), automatically engage N if the gear has
or DOWN, the system will exit the “AUTO
approximately. jammed.
easy exit” mode.
During prolonged stops with the engine
�
R
running, it is advisable to keep the
gearshift in N. 5
On downhill stretches, if you allow the
vehicle to move forward in N, when an
UP-shift is requested, the system will
engage a gear in relation to the vehicle 6
speed.

For safety reasons, the system activates the

With the engine on and the vehicle
stationary, you can shift directly from 1st to
buzzer and automatically shifts to N
when, with the vehicle stationary, the
7
R by pressing button R on the center
engine running and a gear engaged:
console, and from reverse to 1st gear by
pulling the UP lever towards the steering - the brake or the accelerator pedal is not
wheel. depressed for more than 50 seconds
8
103
- the brake pedal is depressed for more In any event, it is advisable to:
If the vehicle is stopped on an uphill
than 10 minutes - Shift gears without releasing the
stretch, do not use the accelerator
- the door is opened without depressing pedal to keep it stationary. Use the accelerator pedal if it is depressed
the brake or the accelerator pedal brake and press the accelerator pedal - Wait until gearshifting has been
- the engine compartment lid is opened. only when ready to move. completed before requesting the next
The buzzer may also sound to warn shift, avoiding a rapid sequence of
WARNING the driver that the clutch is starting If the accelerator pedal is fully depressed multiple requests.
to overheat. This may occur if you very quickly when the CST system is off,
use the accelerator pedal when the the vehicle will have a “performance” start UP-shift due to engine overrevving
vehicle is stationary on a hill or with skidding of the driving wheels, even The system “automatically” engages a
during the “pick-up” maneuver. in good grip conditions. higher gear if the accelerator pedal is
In these cases, you must release the depressed and the engine approaches the
Gearshifting (F1 gearbox) “runaway speed rate” (overrevving). This
accelerator pedal and only use the brake
pedal to keep the vehicle stationary or, UP-shifting will not occur when the system is in
where possible, start off immediately. RACE mode and the CST system is off.
Use the right-hand UP lever, even without
releasing the accelerator pedal.
Important DOWN-shifting
An UP-shift request will not be accepted
- When the vehicle is stationary with a if engagement of the requested gear Use the left-hand DOWN lever, even
gear engaged, always hold the brake would force the engine to run at too low without releasing the accelerator pedal.
pedal depressed until you are ready to RPM (underrevving) or if an UP-shift is A DOWN-shift request is not accepted if
move. already in progress due to engine engagement of the requested gear would
overrevving. Gearshifting will be force the engine beyond a certain RPM or
- Do not “rev the engine” using the
increasingly faster as the performance if a DOWN-shift is already in progress
accelerator pedal to start off.
requested by the driver increases, i.e., as due to a too low engine RPM.
- Shift to reverse only when the vehicle both the engine RPM and the travel of
has come to a complete stop and the accelerator pedal increase.
keeping the brake pedal depressed.

104
 About your vehicle

In any event, it is advisable to:

1
F1 – SUPERFAST gearshifting
- shift gears without releasing the Using the elastic power of the transmission

2
accelerator pedal if it is depressed devices and the integrated electronic
- if a DOWN-shift is requested to start management of engine and gearbox, the
overtaking, where rapid acceleration is F1-SuperFast system enhances vehicle
required, press the accelerator pedal just performance.
before moving the lever
- wait until gearshifting is completed
before requesting the next one, avoiding
The different gearshifting stages (torque
reduction and clutch disengagement, gear
disengagement and engagement and
3
a rapid sequence of multiple requests. subsequent clutch re-engagement) are
actuated in sequence. F1-SuperFast gearshifting is not available
DOWN-shift due to engine underrevving
- The system shifts down the gears
This results in extremely fast gearshifting,
which is reduced to 100 ms (measured as
in the following conditions:
- “Manettino” set to ICE or LOW GRIP 4
“automatically”, if the engine runs below “acceleration gap”). - engine running at < 5000 RPM
the minimum RPM, set at 1250 RPM. F1-SuperFast gearshifting activates only - lateral acceleration > 0.9 g
- The DOWN-shift request from the lever
is ignored if gearshifting due to a too
in the following conditions:
- “Manettino” set to SPORT, RACE or
- skidding of the rear wheels
- traction control activated
5
low engine RPM (underreving) is CST OFF
already in progress. - engine water temperature < 158 °F (70 °C)
RACE mode must be used only on and engine oil temperature < 59 °F (15 °C).
N (Neutral) request
WARNING race tracks.

- engine running at > 5000 RPM Stopping the vehicle (F1 gearbox)
6
If necessary, N can be requested at any
speed. - lateral acceleration < 0.9 g When the vehicle stops, the system
automatically engages 1st gear (unless N
7
Subsequently, if UP-shifting is requested, - no traction control
the system will engage the gear most has already been requested). With the
- engine water temperature > 158 °F (70 °C)
suited to the speed of the vehicle. vehicle stationary and the engine running,
and engine oil temperature > 59 °F (15 °C).
hold the brake pedal down until you are
A message on the TFT display will inform ready to start off again.
the driver that F1-SuperFast gearshifting is
available. 8
105
Turning off the engine and the In this case, the failure warning light will
system (F1 gearbox) illuminate (see page 92) and, before
starting off again, the system and the
The engine can be turned off either with display must be turned off and the
the gearshift in N or a gear engaged. “Starting” procedure repeated.
After turning the ignition key from In any event, it is advisable to:
position II to position 0, the display will
- turn off the engine and the system,
remain on for a few more seconds to
holding the brake pedal depressed
display the gear engaged. If the gearshift
is in N, a buzzer will sound. - do not request a gearshift while the
system is turning off.
Do not start the vehicle before the
display has turned off.
Other system functions
WARNING

Never leave the vehicle with the (F1 gearbox)

gearshift in N. Engage a gear (1st or
R), check that the display is not “Automatic gearshift” mode
flashing and always apply the This mode is activated by pressing the
handbrake. Never leave the vehicle AUTO A button on the center console.
with the engine running. ����
Activation is indicated by the word AUTO
Never remove the key when the shown on the gear display, on the
WARNING vehicle is moving! The system and instrument panel and on the TFT display.
the display will remain active, but The system will automatically shift the
malfunctioning, until the vehicle is gears UP and DOWN according to the
stopped. In addition, the steering vehicle speed, the engine RPM and the
wheel will lock automatically with R torque/power requested by the driver.
the first turn of the steering wheel. When the vehicle is stationary, if the driver
� requests N, 1st gear or R, the system will
not shift from “Automatic” to “Manual”.
The “Automatic” mode can only be exited
by operating the AUTO A control button.
In “Automatic” mode, if you operate the

106
 About your vehicle

UP and DOWN levers, the system will If you then request “AUTO” mode by
1
Starting and driving the vehicle
allow you to shift gears using the lever, pressing the control button A AUTO, the (Mechanical Gearbox)
but it will then switch back to “Automatic” system will use all the “Automatic” mode
mode.
“AUTO easy exit” mode
gearshifting features.
Push start (F1 gearbox)
Starting the engine
Before starting the engine, make sure that
2
the alarm system and all electrical devices
The vehicle is always started in “AUTO In the event that the ignition system with high power absorption are turned
easy exit” mode, unless it was turned off
with the gearbox in “AUTO” mode.
Activation is signaled by the word
malfunctions, you can “push start” the
vehicle as follows:
- perform the “system starting” procedure
off.
- Ensure that the handbrake is engaged. 3
AUTO ▼ appearing on the gear display, - Put the gearshift lever into neutral.
(see page 100)
on the instrument panel. - Fully depress the clutch pedal without
- with the gearshift in N, as the vehicle
speed is increasing, request an UP-shift.
pushing the accelerator.
4
This procedure should be avoided
unless there is an emergency situation! 5
3

Restarting the engine (F1gearbox) R

1
5
In the event that the engine is turned off
6
The system will automatically shift the
accidentally, restart it using the ENGINE
START button, after turning the key to 0
and then to II: the engine will start
2
4
6
gears UP and DOWN according to the immediately.
vehicle speed, the engine RPM and the
torque/power requested by the driver.
In “AUTO easy exit” mode, if you operate
the control levers UP and DOWN (with
7
the vehicle in motion) the system will exit
“AUTO” mode to switch to “Manual”
mode.
8
107
- Turn the ignition key to position II and If the engine fails to start after several When shifting down, be careful not to
wait until the words Check OK are attempts, check for one of the following exceed the maximum permitted engine
viewed on the TFT display. If the words causes: RPM (indicated on the tachometer in the
Check OK do not appear, turn the key - insufficient speed of the starter motor red area).
back to position 0, wait a few seconds (flat battery) - Engage reverse gear only when the
and repeat the procedure. vehicle is stationary: push the gearshift
- ignition device faulty
- Press the ENGINE START button and lever downwards and then move it to
- electrical contacts faulty
release it as soon as the engine starts. Do the left and forward.
not hold the ENGINE START button - fuel pump fuses blown.
down for a long time. Do not run the engine at speeds higher While driving
than 4000 RPM until the engine oil (Mechanical Gearbox)
temperature has reached at least
149 - 158 °F – 65 - 70 °C. Never drive, not even downhill, with the
tachometer pointer near the peak engine
Driving the vehicle speed.
(Mechanical Gearbox) When the tachometer pointer approaches
peak speed (the red zone), the driver
When the engine has started: must be very careful to avoid exceeding
- Fully depress the clutch pedal and move that limit.
the gearshift lever to 1st gear. In normal conditions, all the red and
Use 1st gear for parking or for amber warning lights (for the suspension
starting uphill. and ASR systems) on the multi-function
If the vehicle fails to start, turn the key
WARNING

display must be off. If on, these lights

back to position 0 before repeating the - Completely release the handbrake. indicate a malfunction in the
procedure. corresponding system.
- Slowly release the clutch pedal while
- After the engine has started, the words gradually accelerating. Ensure proper functioning of the various
ENGINE ON will be displayed. devices by checking the relative control
- Then engage the other gears, fully
depressing the clutch pedal and moving gauges.
the gearshift lever into the next position.

108
 About your vehicle

Continuing to drive when a red

1
Parking Parking maneuver
WARNING warning light is on could cause
serious damage to the vehicle and To assist the driver during parking

2
Apply the handbrake, put the gearshift
affect its operation and performance. maneuvers, the vehicle can come
lever into 1st, whether parking uphill
equipped with optional sensors, located in
After sports-style driving, let the or downhill, turn the wheels inwards
the front and rear bumper.
engine idle for several minutes and turn off the engine (these
before turning it off, in order to procedures are valid for all versions,
stabilize the temperatures. both with mechanical and F1 gearbox).
3
Do not coast downhill with the As the 1st gear is the most reduced, it is
WARNING engine off, as the servo brake will no more suited to use the engine as a brake.
longer function due to the vacuum
4
When parking on a steep slope, use a
decrease and thus, after a less wedge to block the wheels.
braking attempts, the system will Never leave the ignition key in position II.
become inefficient.
Always remove the key when getting out
of the vehicle.

WARNING
Never leave children unattended in
the vehicle.
5
Do not park the vehicle on
flammable materials (e.g., paper,
grass, dry leaves, etc.). They could
catch fire if they come into contact
6
with hot parts of the exhaust system.
Do not leave the engine running
with the vehicle unattended.
7
8
109
 To help ensure the system proper However, the driver remains fully When reverse gear is engaged, an acoustic
WARNING functioning, the sensors positioned WARNING responsible for parking maneuvers signal (beep) warns the driver that the
on the bumper must be kept clean and in other potentially dangerous system is active.
(remove any mud, dirt, snow or ice). situations. The system has been The system then begins to beep as soon
When approaching obstacles found in designed only as a supplementary as an obstacle is detected, and the tone
front or behind the vehicle, the parking aid during parking maneuvers, since frequency increases as the vehicle
sensors provide the driver with it allows the driver to detect approaches the obstacle.
information on their distance. obstacles outside his field of vision.
When the obstacle is located at a distance
The driver receives information about the Use of the sensors therefore does of less than 15.7 in. (40 cm), the beep is
presence and distance of the obstacles not mean that the driver can be less continuous.
both by means of acoustic signals, the careful and attentive and not watch
The warning beep stops immediately if
tone frequency of which increases as the out for persons and obstacles during
the distance between the vehicle and the
obstacle gets closer, and by means of parking maneuvers.
obstacle increases.
visual warnings on the TFT display (see The parking system sensors, housed in the The tone cycle is constant if the distance
the “Carrozzeria Scaglietti” User’s rear bumper, are activated automatically, measured by the central sensors remains
Manual). with the key at position II, when reversing. unaltered.
By supplementing the driver’s direct If the vehicle is equipped with front
For the TFT display graphic configuration,
visual information with that provided by sensors, these can be activated by pressing
please consult the “Carrozzeria Scaglietti”
the system acoustic signals and visual the relative button on the center console.
User’s Manual.
warnings, potential collisions can be
avoided during maneuvers.
Cleaning the sensors
When cleaning the sensors, take special
care not to scratch or damage them;
therefore, do not use dry, rough or hard
cloths.
The sensors must be washed with clean
water, possibly with car shampoo added.

110
 About your vehicle

In car-washes which use steam jet or high Failure signals

1
During parking maneuvers, always take
pressure cleaning machines, keep the The system ECU checks all of the the greatest care as there may be
nozzle at least 4 in. (10 cm) away from
2
components every time reverse is obstacles located above or underneath
the sensors. engaged. the sensors.
Should you need to repaint the bumper A parking sensor system failure will be In certain circumstances, objects
or in case of paint touch-ups in the sensor indicated on the TFT display. located near the rear of the vehicle are
area, please contact exclusively your

3
not detected by the system and
Authorized Ferrari Dealer. Incorrect
therefore may damage the vehicle or
painting/touch-ups could affect the
be damaged themselves.
parking sensor operation. ��������������
�������

The signals transmitted by the sensors

4
Sensor range
can also be altered by damage to the
The sensors allow the system to monitor sensors or by dirt, snow or ice on the
the rear of the vehicle, as their position sensors or even by ultrasound systems
covers the central and lateral zones at the (e.g., pneumatic truck brakes or
rear of the vehicle.
5
pneumatic hammers) in the vicinity.
In the event of an obstacle located in a
mid area, this will be detected at distances In the event of a failure warning signal, The driver is fully responsible for
of less than 55 in. (1.40 m), depending on stop the vehicle and turn the ignition key WARNING parking and other potentially
the type of obstacle and its dimensions. to position 0 (Stop). Then try to clean the dangerous maneuvers. During these
If the obstacle is located in a lateral
position, it will be detected at distances of
sensors or move away from any
ultrasound sources (e.g., pneumatic truck
maneuvers, always make sure there
are no people (especially children)
or animals in the maneuvering area.
6
less than 31.5 in. (0.8 m). brakes or pneumatic hammers) and turn
the key back to II. If the situation causing The parking sensors must be
the malfunction has been corrected, the considered an aid for the driver
system starts working again and the
failure warning buzzer stops. If the failure
who, in any case, must never take
less care during potentially 7
warning buzzer remains on, contact your dangerous maneuvers, even if they
Authorized Ferrari Dealer to have the are performed at low speeds.
system checked.
8
111
Proper driving - Do not drink alcoholic beverages before Drunk driving, or driving under the
and during the journey. WARNING influence of drugs, alcohol or certain
For proper driving, it is essential that medicines is extremely dangerous
the driver be aware of the best driving for yourself and others.
techniques suited to various At regular intervals, check the following:
circumstances. Always try to prevent - Tire pressure and condition. Traveling without your seat belt
dangerous situations by driving with fastened increases the risk of serious
- Engine oil level.
caution. injury and death in the event of a
- Engine coolant level and system collision. Always fasten the seat belt
condition. and the child seat, if any.
Before you drive
- Brake fluid level. Deactivate the passenger’s airbag
- Adjust the position of the seat, steering (where possible) if a child seat is
- Steering fluid level.
wheel and rear-view mirrors, in order to fitted on the front seat.
obtain the best driving position. - Windshield washer fluid level.
Do not travel with objects lying
- Adjust the backrest so that your chest is around on the floor, especially in
upright and your head is as close to the When traveling
front of the driver’s seat: in the event
headrest as possible. - Caution is the number one rule for safe of braking, these could slide under
- Carefully adjust the headrest so that driving, which also means you should the pedals, making it impossible to
your head, and not the neck, is resting take other people’s behavior into brake or accelerate.
against it. Make sure that nothing (e.g., consideration.
Additionally, ensure that any floor
floor mat, etc.) is blocking the pedals. - Follow the Road Regulations of the mats fit correctly.
- Check that the lights and headlights are country in which you are driving, and
always respect the speed limit. Water, ice and salt spread on icy
working properly. roads may deposit on the brake discs
- Make sure that any child restraint - Always make sure that the driver and and reduce the efficiency of the
systems (e.g., child seats, etc.) are the passengers have their seat belts initial braking.
properly fixed on the passenger seat. fastened and that all children are
traveling in suitable child seats.
- Your reflexes are quicker if you eat
lightly before driving: avoid heavy meals - Good personal physical conditions
before a trip. ensure you can drive long distances
safely.

112
 About your vehicle

- Make regular stops to loosen up your - Use the high beams only outside of - Do not drive through puddles at high
1
limbs and refresh yourself, and avoid urban areas and when you are sure that speeds as you do not know how deep
driving for hours on end. they will not disturb other drivers. they may be. Traveling through a puddle
- Keep a constant air circulation in the
passenger compartment.
- Turn off the high beams when you see
oncoming vehicles and use the low
at high speed can result in losing control
of the vehicle (“aquaplaning”): hold the
2
beams. steering wheel firmly.
- Never coast downhill with the engine
off: in these conditions the engine brake, - Keep the lights and headlights clean. If the road is wet, reduce your speed
servo brake and power steering are
inefficient, braking requires greater
- Watch out for animals crossing the road
when traveling outside urban areas.
to avoid “aquaplaning” phenomena,
WARNING

during which the tire no longer

touches the road surface. This is due
3
pressure on the pedal and steering will
be harder. to the fact that, when the road is
Driving in the rain very wet and the vehicle speed is
Driving at night
Rain and wet roads can cause hazardous
situations.
high, the side channels of the tire
tread, because of their particular 4
When you are traveling at night, follow All maneuvers are more difficult on a wet shape or insufficient depth, are not
these fundamental rules: roads, as the tires have significantly less capable of removing all of the water

5
- Reduce speed, particularly on dark grip on the road. This means that the channelled, so that a layer of water
roads. braking distances increase considerably exists between the road surface and
and road-holding decreases. the tire. The fluid pressure generated
- Driving conditions are more demanding
is so high as to support the vehicle’s
at night, so take particular care. Below is some advice for driving in the
weight, making it impossible for the

6
- If you start feeling tired or sleepy, stop rain:
driver to control the vehicle.
immediately: to continue driving would - Keep a greater safety distance between
- Use the ventilation system to defog the
be a risk for yourself and for others. yourself and the other vehicles and
windshield (see page 124) and to avoid
Continue only after you have had a rest. reduce your speed.
visibility problems.
- At night, it is difficult to evaluate the - When it is raining very hard, visibility is
speed of the vehicles by seeing their
lights only: keep at a greater safety
also reduced. In these cases, to make
yourself more visible to others, turn on
- Periodically check the condition of the
windshield wiper blades. 7
distance than you would during the day. the low beams even during the day.

8
113
Driving in fog Driving on mountain roads - Given the poor grip, use the engine
Whenever possible, avoid driving if the brake as much as possible and avoid
Below is some advice for driving on steep sudden braking.
fog is thick. If you have to drive in misty mountain roads:
conditions, or if there is thick fog or fog - Avoid sudden acceleration and sharp
banks, follow these rules: - To prevent the brakes from overheating changes in direction.
when driving downhill, use the engine
- Keep a moderate speed. to brake by engaging a lower gear. - During the winter season, even
- Turn on the low beams, also during the apparently dry roads can have icy
- Never coast downhill or drive downhill sections.
day, and use the rear fog lights. Avoid with the engine off or in neutral, nor
using the high beams. with the ignition key removed from the Therefore, be careful when driving along
On stretches where visibility is good, steering column. stretches of road in the shade as there
turn off the rear fog lights, as they may be icy patches.
- Drive at a moderate speeds and do not
WARNING

are very bright and may be annoying “cut” corners.

for the occupants of the vehicles Driving with the “ABS” braking system
behind you. - Remember that overtaking uphill is
slower and requires a longer free stretch The ABS system assists the driver as
- Remember that fog makes the road damp of road. If you are overtaken when follows:
and therefore all maneuvers are more driving uphill, ensure that the other - It prevents the wheels from locking and
difficult and braking distances are longer. vehicle can pass easily. skidding during emergency braking,
- Keep a safe distance from the vehicle in particularly in low-grip conditions.
front of you. Driving on snowy or icy roads - It allows braking and changing direction
- As much as possible, avoid suddenly Below is some advice for driving in these at the same time. This feature is affected
changing speed and direction. conditions: by the physical limits and lateral grip of
the tires.
- As much as possible, avoid overtaking. - Keep a very moderate speed.
- When the ABS is activated, you will feel
- In the event of an emergency stop, (e.g., - Keep a safe distance from the vehicles in a slight pulsing of the brake pedal
failures, inability to proceed due to poor front of you. during emergency braking or in low-grip
visibility conditions, etc.) try to leave the - Fit snow tires approved for the vehicle. conditions. Do not release the pedal but
main driving lane. Then turn on the continue to push it to give continuity to
hazard warning lights and, if possible, the the braking action.
low beams. When approaching another
vehicle, sound the horn rhythmically.

114
 About your vehicle

- The ABS system is designed to prevent to enhance driving comfort and the
1
the wheels from locking, but it does not CST system remains set to the
increase the physical limits of grip previous level.
between the tires and the road: keep a
safe distance from the vehicles ahead
SPORT mode is the basic driving
mode for the vehicle and provides
2
and reduce speed before curves. the best compromise between
stability and performance. This
Driving using the “Manettino” (driving mode
control switch)
setting helps ensure stability only
in dry-high grip conditions and not 3
The “Manettino” A on the steering wheel, on low-grip road surfaces (in this
allows the driver to use the vehicle case, it is advisable to return to
potential in a quick and easy way. In ICE mode, increased stability - Low Grip mode). In this mode, the
which is essential for driving on
roads where grip is very low (e.g.,
vehicle optimal performance can be
experienced on open roads. For
4
snow or ice) - has priority over this reason, the suspension
performance, which is significantly damping level is shifted to a higher
�
reduced. Traction stability control
(CST) is at the maximum level
(Level 1). The vehicle has an
one, so as to enhance performance,
handling and stability at high
speeds. Also the CST system
5
extremely “smooth” behavior. switches to a different level
(Level 2), offering the driver
Low Grip mode ensures stability
on both dry and wet roads. It is
therefore recommended on roads
greater driving freedom. The F1-
Trac system does not correct 6
engine torque significantly when in
where grip is poor (e.g., rain), SPORT mode (for this reason, it
There are five modes available, which can
slippery or extremely uneven roads, does not ensure stability on low-
be selected according to the grip level
(from low to high) and consequently to
the level of driving assistance required
but also to enhance comfort during
city driving. In this configuration,
unlike the previous one, the driver
grip road surfaces).
RACE mode must be used only on
7
(from high to none). race tracks.
may drive the vehicle using the
WARNING

gearbox as desired.
Suspension damping is optimized
8
115
 On vehicles equipped with F1 Ignition switch To facilitate steering wheel release, turn
gearbox, gearshifting is faster so as the steering wheel slightly in both
The ignition key can be turned to 2 directions while turning the ignition key.
to reduce gear change times as
positions:
much as possible. The CST shifts
to Level 3 (engine power Position 0 – Stop Position II – Ignition
reductions are minimal) and the Engine off, key removable. Turning the key to this position, the TFT
suspension stiffens further. In this display will check the signals coming from
position, the driver has full control the vehicle systems.
of the vehicle and the operation of
If no malfunctions are found after starting
all engine control systems is
up, the words “Check OK” will be
reduced to a minimum. Stability is
displayed.
not ensured.
Never remove the key when the
The CST is deactivated. Vehicle
vehicle is moving!
stability is no longer controlled, ��
WARNING

but is completely in the hands of The steering wheel will lock

the driver. The only aids that are automatically with the first turn of
still active are those that cannot be the steering wheel.
deactivated, such as the ABS and Always remove the key from the
EBD. When the brake pedal is � ignition when you get out of the
depressed, the VDC system is vehicle!
reactivated, while the F1-Trac Never leave children unattended in
system remains deactivated. the vehicle.
Gearshifting speed (on vehicles
with F1 gearbox) and damping When the key is even only partially
control remain the same as in extracted, the steering column is locked.
RACE mode.
The hazard warning lights and the
parking lights can be activated.

116
 About your vehicle

1
Handbrake lever
To engage the handbrake, pull the lever A �
fully upwards, until the rear wheels lock.
2
�

4
A

To release the handbrake, slightly pull the

lever upwards and press the release
button C. Lower the lever fully, holding
5
the button pressed.

6
With the ignition key in position II, the The warning light will turn off when the
warning light B illuminates to indicate handbrake is fully released.
that the handbrake is engaged. Always apply the handbrake when
WARNING the vehicle is parked.
After hearing a series of clicks by
pulling the handbrake lever, the
vehicle should be blocked. If this is
7
not the case, please contact your
Authorized Ferrari Dealer

8
117
Adjustments - height adjustment: push the control Use control C to adjust the seat cushion
upward or downward sides. Push the control on the seat
Seats - seat inclination (tilting): push the front symbols to increase or decrease the seat
end of the control upward or downward cushion side supports.
Never adjust the seat while driving: to adjust the inclination of the front part Use control D to adjust the seat side
WARNING you may lose control of the vehicle. of the seat cushion; push the rear end of support. Push the control on the seat
the control upward or downward to symbols to increase or decrease the seat
The seat position can be electrically adjust- adjust the inclination of the rear part of side support.
ed using controls A, B, C and D. the seat cushion.

� �
� �

Three adjustments are possible using Use control B to adjust the seat backrest
control A: inclination. Push the control forward or
- forward/backward adjustment: push the backward to adjust the seat backrest
control forward or backward inclination.

118
 About your vehicle

Driver’s seat position memory (optional) The memorization of a new seat position
1
This device allows you to memorize and cancels the one previously stored with the
same button.
2
recall three different seat positions.
You can memorize the seat position only To recall one of the memorized positions
when the ignition is in position II. when the door is open, press button 1, 2 or
3 E for about 3 seconds.
After adjusting the seats by means of
the controls described above, push one of To recall the memorized position with the
the three buttons 1, 2 or 3 E, each
corresponding to a memorizable position,
door closed, press the relative button until
you hear the tone indicating that the seat
3
until you hear a double confirmation tone. has stopped.
Backrest tilting
Press button X to tilt the backrest forward.
4
�

Sitting in a reclined position while

WARNING the vehicle is in motion could be
dangerous. The backrest should not
5
be tilted too far back. The 3-point X
shoulder/lap belt must be firmly
secured against the occupant’s body
in order to function properly.
Therefore, both the driver and
6
passenger’s backrests must always be
in an upright position while the
vehicle is in motion; otherwise the
3-point shoulder/lap belt would not The lumbar support adjustment will not be
memorized with the seat position.
7
remain firmly secured against the
occupant’s body. Press button X before moving the backrest
Serious injury could result. back to its normal position.
8
119
Seat heating system (optional) Adjusting the steering wheel To help the driver when entering or
Turn control F to activate the seat heating exiting the vehicle, the steering wheel is
The steering wheel height and depth can lifted automatically.
function. be electrically adjusted. It can only be
When this function is active for one or adjusted if the ignition key is in Rear-view mirrors
more seats, the relative warning light on position II.
the instrument panel illuminates. Move control A (to the left of the steering Internal rear-view mirror
Using control F, the driver can adjust the column) in the four directions to adjust This mirror can be adjusted manually.
heating, choosing from 3 levels identified the steering wheel. For the anti-dazzling effect, move lever A
on the control with the numbers 1, 2 The steering wheel position is memorized, forwards.
and 3. together with the position of the external
rear-view mirrors, when the driver’s seat
position is stored.
Do not adjust the steering wheel
WARNING when the vehicle is moving.

120
 About your vehicle

External rear-view mirrors In the models equipped with memory

1
These mirrors can be electrically adjusted seats, every time the seat position is
memorized, the external rear view mirror
2
using control B (with the ignition key in
position II) and are equipped with position is also stored automatically, both
defogging elements. for the normal traveling direction and for
reverse maneuvering.
1) Mirror selection: using control B,
select the mirror you wish to adjust To memorize a new position of the
(right- or left-hand). external rear-view mirrors, turn the
ignition key to position II and adjust the 3
position of the mirrors; then engage
B Reverse gear and reposition the external
mirrors to ensure optimal visibility to
perform the maneuver, then disengage
Reverse gear.
4
Finally, press one of the buttons 1, 2 or 3
on the seat (see page 119), each one
Once adjustment is complete, move the
control B into the upper central position,
where it will be locked, in order to avoid
corresponding to a memorizable position,
until a double tone confirms the
procedure is complete.
5
changing the setting inadvertently. The new position of the external rear-view
�

6
The mirrors will yield in both directions mirrors will be automatically memorized
in the event of a collision: if necessary, the together with the seat position.
mirrors can be pushed both backwards In addition, the mirror positions can be
and forwards. adjusted for both the normal traveling
2) Mirror positioning: move control B in direction and for reverse maneuvering.
the four directions (up – down – right
– left) to adjust each of the rear-view
The mirrors must always be in the open
position while driving.
7
mirrors.

8
121
Air conditioning and heating Controls I Right-hand temperature setting
system J Residual heat function.

Operating modes Starting

Automatic Fully automatic management: turn controls
This mode automatically adjusts the air � � � � � C, E and G to the “AUT” position.
distribution, temperature and ventilation
levels according to the temperature set by Deactivation
the user. Turning the (fan speed) control E to
“OFF”.
Partially Automatic
This mode allows the user to adjust
certain parameters manually, while others � � � � �
remain automatic.

Manual
This mode allows the user to set the
values to suit the passengers’ needs. A Left-hand temperature setting
B Air conditioning compressor
deactivation
C Left-hand air distribution setting
D Windshield defogging/demisting
E Fan speed adjustment
F Recirculation function
G Right-hand air distribution setting
H Rear window and external rear-view
mirrors defogging/demisting

122
 About your vehicle

1
Air conditioning control switch B Temperature setting controls A and I Residual heat function J
Released (LED off) They are used to set the desired This function allows the user to
The air conditioner is on.
The air is cooled and/or only
temperature in the passenger
compartment.
maintain the temperature set for the
passenger compartment for a 2
The “LO” and “HI” (minimum and specific time (15 minutes), even
dehumidified according to the
maximum, respectively) air after the key has been turned to 0
temperature set.
(for external temperatures lower
Pressed (LED on)
temperature settings are activated at
the opposite end positions. than 77°F (25°C)).
To activate this function, press the
3
The air conditioner is off.
Fan speed control E “REST” button before turning the
However, heating is still enabled key to 0. The system will use the hot

4
and will activate according to the It has three operating modes: water recirculation pump and the
temperature set. first fan speed to maintain the
Automatic “AUT”
temperature.
Air distribution controls C and G The air flow is controlled by the
electronic system, according to the
They can operate in two modes:

Automatic “AUT”
selected temperature to be reached
and maintained. 5
The air flow distribution is Manual “OFF”
controlled by the electronic system, Turn the control to this position to
depending on the ambient
conditions and the temperature set.
turn off the air conditioning and to
only allow air inlet from the outside
6
when the vehicle is moving.
Manual

7
This is used to direct the air flow in Fan speed
the six positions of the respective The four setting positions allow the
areas (driver-passenger). occupants to select the air flow rate.

8
123
Air recirculation switch F Windshield defogging/demisting Once the internal temperature has
switch D stabilized at the desired level, you are
Released (LED off) advised not to change the position of the
The air flow comes from the outside. Press this switch (LED on) to temperature selection switch unless the
In automatic mode, when outside activate windshield defogging/ external temperature changes drastically.
temperatures exceed 90 °F (32 °C), demisting.
To deactivate this feature, press the The air coming out of the vents does
the air recirculation feature remains
switch again (LED off). not correspond to the temperature
on with a 60-second pause every
requested by the user, but is the
twenty minutes, to refresh the air.
temperature required to maintain the
If you activate the windshield Defogging/demisting switch for desired temperature inside the
washer function, the air recirculation rear window and external rear-view passenger compartment.
feature activates for 20 seconds, to mirrors H
prevent any smell of detergent
products from entering the Press this switch (LED on) to
passenger compartment. activate the rear window and rear-
view mirror defogging/demisting.
Pressed (LED on)
If it is not deactivated within thirty
The air flow comes from inside the minutes after activation, this
passenger compartment. function deactivates automatically.
The recirculation feature increases It is however advisable to deactivate
air heating or cooling. it once the defogging/demisting
process is complete.

Prolonged use is not advisable.

124
 About your vehicle

Adjusting the air vents Maintenance Passenger compartment

1
The adjustable air vents are positioned on The pollen filter must be replaced every accessories
2
the sides and in the center of the year, as indicated in the “Maintenance
Glove compartment
dashboard. Schedule”.
It is located on the passenger’s side of the
Air flow direction adjustment A. Sun radiation sensor dashboard, and it is always accessible
Air flow rate adjustment B. when the key is in position II, and for
This sensor is positioned on the
Turned counterclockwise: open.
Turned clockwise: closed.
instrument panel and it helps optimize
ventilation and temperature control inside
the compartment, depending upon the
approx. ten minutes after the key is
removed or turned to position 0. 3
angle of the sun rays.
B
4
5
6
A

It is advisable to keep the air flow 7

control B set to open and to direct the
air flow to a neutral position A.

8
125
To access the glove compartment, push To close the glove compartment, push the Other compartments
the button A on the center console. upper part of its door until you hear it They are located on the lower part of the
The glove compartment is illuminated by click into place. doors and on the center console.
a light which turns on automatically when Underneath the dashboard, in position
the door is opened. with the external edge of the glove
Keep the glove compartment closed compartment, there is a safety string B for
WARNING while driving. manual opening in an emergency.

R
�
�

126
 About your vehicle

Ashtray Clothing hooks Sun visors

1
To access the ashtray E or the cigarette They are fitted in the rear of the The sun visors can be adjusted by moving

2
lighter F, push the cover G backward. To passenger compartment. To release the them downwards. There is a map pocket I
clean the ashtray, extract it pulling it up- hook, press the button H. To reposition on the back of the sun visor.
ward. The cigarette lighter F is activated the hook, push it upwards into its seat.
by fully pushing it in. It only works when
the ignition key is in position II. After
reaching the required temperature, the
cigarette lighter is automatically released
to its initial position and is ready to be
�
�
3
used.

4
�

Move the hooks to the closed position

when they are not used.
Map pocket
A map pocket L is located between the
5
� � two seats.

Do not use the cigarette lighter seat

6
WARNING as a power socket for electrical items
of any kind! The cigarette lighter
reaches very high temperatures.
Handle it with care to avoid risk of
burns and fire. It is possible to �
7
connect the emergency tire repair
and inflation kit ONLY for the time
necessary for the operation.
8
127
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
 Toolkit
Replacing the headlight bulbs
Replacing the taillight bulbs
Replacing other light bulbs
Light bulbs
Replacing a fuse
Replacing a wheel
Towing hook
Fuel inertia switch
Checking the battery
Exhaust system overheating
alarm devices
Engine malfunction
alarm devices
Replacing the brake pads
and brake discs
 In the event of repairs performed Emergency tire repair and inflation kit
WARNING using the toolkit provided, you must: In the event of a puncture or low
- use suitable personal protection pressure of a tire, the kit is designed to
(e.g., gloves) repair and/or inflate the tire sufficiently
- take suitable precautions (e.g., to continue the journey.
when changing a tire, never lie
For correct use of the repair and
under the vehicle raised on the
inflation kit, refer to the instruction
jack)
manual supplied with the kit.
- have the basic and specific skills
required for working with electrical
parts/components. Give the kit and instruction manual
WARNING supplied with the kit to the personnel
that will handle the tire repair.
Toolkit
In the event of a puncture caused by
Toolkit bag WARNING small objects, tires can be repaired
The toolkit bag is found in the luggage with tears or holes that have up to a
compartment and it contains the 0.16 in. (4 mm) diameter on the
necessary tools for a first emergency tire tread and shoulder.
repair work:
Tears on the sides of the tire cannot
• set of flat wrenches WARNING be repaired.
• insulated cutting pliers
• screwdriver for slotted screws Do not use the tire repair kit if the
• Phillips head screwdriver WARNING tire is damaged after driving with a
flat tire.
• towing hook
• set of spare light bulbs and fuses. If the wheel is damaged and has
WARNING caused an air leakage, the tire cannot
be repaired.

130
 Advice for Emergency situations

Do not remove foreign objects If pressure has dropped to below The spray contains ethylene glycol
1
WARNING (screws or nails) that have WARNING 26 psi (1.8 bar), stop driving: the WARNING and latex, and may cause an allergic
penetrated the tire. kit is then unable to provide a tight reaction. Harmful if swallowed.

WARNING
After using the repair kit, the vehicle
must however be considered to be in
seal because the tire may be too
severely damaged. Contact an
Irritating to eyes. May cause irritation
by inhalation and skin contact. Avoid
2
an emergency situation: drive with Authorized Ferrari Dealer. contact with eyes, skin and clothing.
the utmost care (maximum If, on the other hand, the pressure is In case of contact, rinse immediately
permissible speed 50 mph –
80 km/h).
at least 26 psi (1.8 bar), pump the
tire up to the correct pressure and
continue driving.
with plenty of water. If swallowed, do
not induce vomiting, rinse mouth,
drink plenty of water and seek
3
Place the sticker supplied with the immediate medical advice. Keep out
kit where it can easily be seen by the Drive carefully to the nearest
of reach of children. The product
WARNING

4
driver to indicate that the tire has Authorized Ferrari Dealer.
should not be used by asthma
been repaired using the tire repair kit. sufferers. Do not inhale vapors when
Drive carefully especially on curves. The repaired tire must be replaced as using. In the event of an allergic
WARNING
WARNING soon as possible and the workshop reaction, seek immediate medical
personnel must be informed that the advice. Store the spray can in its
WARNING
Do not suddenly accelerate or brake. tire was treated with tire repair fluid. special case away from sources of
heat.
5
The kit is to be used to temporarily The liquid sealant has an expiration
Keep the kit in its box and out of
repair only one tire punctured by date.
children’s reach.
6
WARNING WARNING

small objects: the kit may not be

useful in the case of large punctures Replace the spray can containing the
or tearing. expired liquid sealant. Do not dispose
Do not inhale or swallow the fluid of the spray can in normal domestic
contained in the cartridge and avoid waste. Dispose of in accordance with
7
After driving for approximately WARNING

10 minutes, stop and recheck the tire contact with the skin and eyes. local regulations.
pressure.
Remember to apply the parking brake.

8
131
 The sealant contained in the Useful accessories
WARNING cartridge in the tire repair kit may In addition to the tools supplied with the
damage the sensor fitted inside the vehicle, the hazard warning triangle and
wheel rim on vehicles equipped with fluorescent safety jacket should always be
the tire pressure monitoring system. kept on board, in order to indicate
In these cases, always have the hazardous situations in compliance with
sensor replaced by an Authorized applicable legislation.
Ferrari Dealer.

Wear the protective gloves supplied

WARNING with the tire repair kit.

132
 Advice for Emergency situations

To replace the light bulb of the front

1
Replacing the headlight bulbs Replacing the front direction indicator and
position light bulbs direction indicator, proceed as follows:

2
• detach the connector B
Before replacing a light bulb in the
headlights, always turn the ignition key
to position 0 and ensure that the
relative fuse is intact.

Turn the wheels completely inwards, then

undo the screws A and extract the panel
3
in the wheelhouse outwards.

4
�
�

The low/high beams are equipped

5
with bi-xenon light bulbs.
• turn the bulb holder counterclockwise
For replacement of the high and low
beam light bulbs, contact your
Authorized Ferrari Dealer.
and extract it from its seat
6
For aiming the headlight beam, please
contact your Authorized Ferrari
Dealer.
7
8
133
 To replace the position light bulb,
proceed as follows:
� • remove the rubber cover D from the �
headlight

�
• remove the bulb C pulling it outwards • replace the pressure-fitted bulb E
• fit the new bulb by fully pushing it into • refit the bulb holder into its seat
place • refit the rubber cover D.
• refit the bulb holder in its seat and turn Refit the panel into the wheelhouse.
it clockwise until it locks
• grip the bulb holder from its tab and
• refit the connector. remove it from its seat

134
 Advice for Emergency situations

1
Replacing the side direction indicator light bulbs Replacing the taillight bulbs
• Remove the transparent cover I on the

2
indicator, taking care not to damage the
bodywork.
• Remove the bulb L by rotating it and
removing it from the bulb holder M.
• Replace the bulb and refit the
transparent cover. 3
• remove the bulb holder B

4
�
�

�
�
5
Before replacing a light bulb in the
taillights, always turn the ignition key
to position 0 and ensure that the
relative fuse is intact.
• remove the bulb pulling it outward and
6
replace it
To replace a taillight bulb, proceed as
• refit the bulb holder and reposition the
follows:
• partially remove the luggage
compartment weather strip
luggage compartment weather strip. 7
8
135
Replacing the license plate light bulb Replacing other light bulbs • Replace the light bulb involved, E or F.
To replace a license plate light bulb,
Roof dome light
proceed as follows:
• Gently pry out with a screwdriver at
• undo the two fastening screws
point C to remove the dome light D
from the roof.

�
�
�

• Refit the dome light, taking care that the

� cables are not crushed, inserting it first
� � from the connector side and then
• remove the transparent cover A from its pushing on the opposite side.
seat and replace the bulb B, which is
pressure fitted into the two contact clips
• refit the transparent cover and the two
fastening screws.

Replacing the auxiliary stop light and side

marker bulbs

For replacement, we recommend you

contact your Authorized Ferrari
Dealer.

136
 Advice for Emergency situations

Glove compartment light, luggage compartment Follow the same procedure for replacing
1
light and underdoor light the underdoor light bulb and the luggage
compartment light.
2
• Gently pry out with a screwdriver at
point G to slightly lift out the light.

�
3
4
�

5
• Remove the light from its seat.
• Remove the pressure-fitted bulb H.
6
• Replace the bulb.

7
• Refit the light, taking care that the
cables are not crushed, inserting it first
from the connector side and the pushing
on the opposite side.

8
137
Light bulbs (12 V, except for low and high beams)

Type Power
Low beams and high beams Xenon (gas discharge) DAS
Front position lights incandescent H6W
Front direction indicator lights incandescent H21W
Side direction indicator lights incandescent T4W
Taillights incandescent R5W
License plate lights incandescent R5W
Auxiliary stop light LED
Rear fog lights incandescent P21W
Dome light incandescent 10W
Spot light incandescent 6W
Glove compartment light incandescent W5W
Courtesy light incandescent W5W
Luggage compartment light incandescent W5W
Reverse gear incandescent H6W

138
 Advice for Emergency situations

To remove fuses, use the tweezers C in the Maxi fuse colors

1
Replacing a fuse
fuse box in the passenger compartment
When an electrical device is not working, Ampere
behind the small door on the dashboard,
check that the corresponding fuse is
intact.
on the left of the steering wheel. yellow
green
20
30
2
A - Fuse intact.
orange 46
B - Fuse blown. �

� �
red
blue
50
60
3
4
Fuse colors

Ampere 5
If the problem persists, contact your dark yellow 5
Authorized Ferrari Dealer. brown 7.5
When replacing a fuse, always use
fuses of the same amperage (same
red 10 6
light blue 15
colors).
yellow 20
The toolkit contains spare fuses. white
green
25
30
7
8
139
Location of the fuse and relay boxes
A, B - Fuses and relays in the engine compartment F, G, H - Fuses and relays in the luggage compartment

C - Body Computer Fuses and relays I, J - Fuses and relays in the passenger compartment,
passenger’s side
D, E - Fuses and relays in the passenger compartment,
driver’s side

H
G
J F

I E

D
C
A

140
 Advice for Emergency situations

1
Fuses and relays in the engine
compartment �

To access these fuses you must:

• open the engine compartment
2
(see “Engine Compartment – Opening”
on page 69)
• remove the box covers A and B.
3
� The box A contains the following relays (R) and maxi-fuses (MF):
4
Ref. Amp. Use
R14 50 air pump
�
5
Ref. Amp. Use
MF5 40 +30 A.C. unit
MF2 60 +30 air pump (Link Box) 6
MF85 40 passenger compartment connected devices 2
MF1 40 +30 ABS (pump) (Link Box)

We recommend that you open only the

boxes in which you need to work, to
7
avoid damaging other components.

8
141
The box B contains the following fuses (R) and maxi-fuses (MF):
�
Ref. Amp. Use
R16 50 LH fans
R15 50 RH fans

Ref. Amp. Use

MF3 40 +30 RH fans (Link Box)
MF4 40 +30 LH fans (Link Box)

Body Computer fuses and relays We recommend that you open only the
�
To access these fuses, remove the door 1 boxes in which you need to work, to
by undoing the two fastening screws. avoid damaging other components.

��

142
 Advice for Emergency situations

The box C contains the following fuses (F):

1
Ref. Amp. Use Ref. Amp. Use
F36
F52
10
15
+30 glove compartment motor
driver seat heating (INT/A connected
F53
F40
10
30
+30 rear fog light
+30 heated rear window (INT/A relay)
2
device relay)
F50 7.5 +15 airbag system
F45
F46
25
15
(not used)
(not used)
F42
F35
7.5
7.5
+15 NFR
+15 CLA (NC), IFR, engine signal socket,
3
F34 20 (not used) relay coils (headlight washer, reverse gear,
F39 10 +30 for NIM, NCL, diagnostic socket OBD, high beams)

F41 15
CSA, CAV, radio/NIT, telephone option
(not used)
F31
F44
7.5
20
INT/A for A.C. unit, NBC
+30 cigarette lighter, passenger seat
4
F47 20 (not used) heating (INT/A connected device relay)
F51 7.5 +15 NCR, F1 control panel
F33
F48
20
20
(not used)
(not used) F12 15 +30 RH low beam 5
F38 15 +30 ratio motor for luggage compartment F13
lock
F43 30 windshield wipers/washer
(INT/A connected device relay)
� 6
F32 10 +30 dome lights

7
F37 10 +15 NQS, +15 CLA (NO), third stop
F49 7.5 +15 for CSG, CSP, NIM, NCL, radio/NIT,
CEM, CRP, telephone option, dome light
panel, windshield wiper controls, steering
column adjustment
8
143
The box C1 contains the following relays (R):

Ref. Amp. Use

R01 20 low beams
R11 30 heated rear window
R12 30 connected devices 1 (controlled by INT/A
ignition switch)
R13 50 connected devices 2 (NBC-controlled)
(option)

��

144
 Advice for Emergency situations

1
Fuses and relays in the passenger
�
compartment (driver-side)
To access these fuses you must:
• lift the passenger compartment trim
���� ���� ��� 2
panel, behind the driver’s seat.
• remove the box covers D and E. ��� ���� ���

3
�
The box D contains the following relays (R):

Ref. Amp. Use

4
R8 20 horns
�
R10
R6
20
20
left-hand injection
high beams 5
R5 30 headlight washers
R29 20 glove compartment motor
R20 20 side marker 6
We recommend that you open only the
boxes in which you need to work, to
avoid damaging other components.
7
8
145
The box E contains the following fuses (F):
�
Ref. Amp. Use
���� ���� ���� ���� ����
F55 20 +30 steering column adjustment
���� ���� ���� ���� ����
(only with basic seat version)
���� ���� ���� ���� ����
F56 30 +30 passenger seat adjustment
���� ���� ���� ����
F91 7.5 +30 NAP (electronics)
F22 30 LH main injection relay
F57 7.5 +15 alternator, NVO, start button
F58 5 +30 NTP
F79 5 +30 NQS
F83 30 +30 NPG power supply
F6 25 +30 from ignition switch
F27 10 +15 LH injection
F77 15 +87 LH oxygen sensor main relay
F26 15 +87 injectors main relay, LH coils
F25 10 solenoid valves, air flow meter, LH diagnostic pump
F24 10 +87 LH main relay
F23 7.5 +30 LH injection
F67 5 +30 front RH - rear LH side marker
F66 5 +30 front LH - rear RH side marker
F18 10 +30 RH low beam
F17 10 +30 LH low beam

146
 Advice for Emergency situations

1
Fuses and relays in the passenger
�
compartment (passenger-side)
To access these fuses you must:
• lift the passenger compartment trim
2
panel, behind the driver’s seat
• remove the box covers J and I.
3
� The box J contains the following fuses (F):

Ref. Amp. Use 4

F76 15 +87 RH oxygen sensor main relay
� F11 15 +87 RH injectors main relay, coils
F10
F9
10
10
+87 main relay, air flow meter, RH solenoid valves
+87 RH main relay (pin F03)
5
F8 7.5 +30 RH injection (pin F62)
F60
F80
20
25
+30 NPG, NPP door lock actuator
+30 Hi-Fi system (bass-box and subwoofer)
6
F84 30 +30 NPP power supply
We recommend that you open only the
7
F61 7.5 +30 NAG (electronics)
boxes in which you need to work, to
avoid damaging other components. F7 30 +30 injection main relay, RH main coil relay
F19 30 +30 starter motor

8
147
Ref. Amp. Use
F30 30 +30 driver seat adjustment (and steering column
adjustment, only with comfort seats)
F15 5 +15 weight sensor ECU (only for the USA)
F14 10 +15 RH injection (coils, fuel pumps relays)
F16 7.5 +30 A.C. compressor
F20 25 +30 headlight washer
F21 15 +30 horns
F28 25 +30 ABS (solenoid valves)
F54 10 +30 ABS (electronics)

The box I contains the following relays (R):

�
Ref. Amp. Use
R7 30 starter motor
R27 20 devices cut-out upon ignition
R4 20 A.C. compressor
R3 20 immobilizer
R2 20 RH main injection relay
R28 20 ignition cut-off with battery charger

148
 Advice for Emergency situations

1
Fuses and relays in the luggage
� �
compartment
To access these fuses you must:
• remove the door 2 on the right-hand
2
side of the luggage compartment, by �
undoing the two fastening screws.

3
�
�

4
The box H contains the following fuses (F) and relays (R):

Ref. Amp. Use

5
• remove the covers on the boxes H, G
and F. R19 20 reverse gear

We recommend that you open only the

boxes in which you need to work, to
R21 20 fuel tank door
6
avoid damaging other components. Ref. Amp. Use
F89 5 +15 NSP and NCS
F59 10 +30 fuel tank door 7
F64 7.5 +30 reverse gear, NSP
F88 30 +30 NCS

8
149
 The box G contains the following maxi-fuses (MF):
�
Ref. Amp. Use
MF81 60 +30 passenger compartment connected devices 1
MF72 40 +30 luggage compartment connected devices
(+side marker coil relay)
MF71 60 +30 passenger compartment connected devices 3
MF70 30 +30 F1 gearbox pump
MF68 30 +30 Hi-Fi system (amplifier)

The box F contains the following fuses (F) and relays (R):
�
Ref. Amp. Use
R17 20 1st speed fuel pump, RH bank
R18 20 2nd speed fuel pump, RH bank
R24 20 1st speed fuel pump, LH bank
R25 20 2nd speed fuel pump, LH bank

Ref. Amp. Use

F78 20 +30 LH fuel pumps
F82 5 +30 alternator sensing
F29 15 +30 battery charger
F63 20 +30 RH fuel pumps
F69 25 +30 NCR

150
 Advice for Emergency situations

• Do not exceed the approved weight

1
Replacing a wheel
limits.
If one or more wheels need to be � �

2
• Do not fit snow chains on the spare
replaced, proceed as follows: wheel.
- Replace the stud bolts with damaged • Never fit more than one spare wheel at a
thread or cone. time.
- Carefully clean the stud bolts before
fitting.
- Absolutely do not lubricate the
Failure to comply with these
instructions could lead to loss of 3
contact surfaces between the stud control of the vehicle and consequently
bolt and the wheel rim, and between to damages to the vehicle and injuries
to the occupants.
the wheel rim and the brake disk.
In order not to remove the anti-lock � Replacing a wheel
4
coating, do not clean the wheel rim
cones with solvents or aggressive • Position the vehicle on an even surface,
products. then engage 1st gear and lock the rear

Collapsible spare wheel (optional)

Warning
• Keep the collapsible spare wheel in
wheels by applying the handbrake.
• If necessary, turn on the hazard
5
On request, the vehicle can come proper working order, checking it at warning lights and place the hazard
equipped with a kit containing: regular intervals to ensure that the triangle at the prescribed distance.

• collapsible spare wheel A with space-

saver tire; the label B indicates the max.
inflation pressure is 60,9 psi (4.2 bar).
• The spare wheel must only be used for
• Take out the spare wheel and tools from
their seat in the luggage compartment.
6
speed permitted (50 mph – 80 km/h) short trips, in emergencies. • Loosen the five wheel fastening stud
• additional toolkit bag C containing: jack • When the spare wheel is fitted, never bolts by approximately one turn, using
and wrench to fasten the wheel stud
bolts.
exceed the maximum speed of (50 mph
– 80 km/h) and drive carefully,
especially around bends and when
the wrench supplied D.
• Place the base of the jack E on flat and 7
firm ground, in position with one of the
overtaking, avoiding accelerating or lifting points F underneath the vehicle
braking suddenly. floor.
8
151
• Raise the vehicle carefully, using the Inflate the collapsible spare wheel
jack, until the wheel is lifted off the WARNING before lowering the car, as otherwise
ground. the rims may be damaged �

• Inflate the collapsible spare wheel using

the inflation kit (page 132). �
The kit must be used in “tire inflation”
� WARNING mode.
Use lever terminal H.

� • Remove the terminal H from the union

J on the cartridge and insert it in the
wheel valve.
• Lower the lever K and start the �
� compressor.
• Inflate to the indicated pressure • Lower the vehicle and remove the jack.
(see page 26 - 27). • Tighten the stud bolts completely,
�
The spare wheel is not equipped moving diagonally from one to the next.
WARNING with the tire pressure monitoring As soon as possible, tighten the stud bolts
If the jack is not positioned correctly, sensor (see label on spare wheel with the torque wrench to 73.8 lb ft
the vehicle could slip off. bag). After installation, it is not (100 Nm).
WARNING

The jack supplied must only be used monitored by the system, but it does
for replacing the wheels. comply with International Regulation
• Completely unscrew the five stud bolts ECE R64/01.
and remove the wheel. Once fitted, we recommend you go
• Fit the deflated collapsible spare wheel to the nearest Authorized Ferrari
and screw in the five stud bolts Dealer.
tightening them snugly.

152
 Advice for Emergency situations

Always follow the applicable driving

1
Towing hook Fuel inertia switch
WARNING and traffic regulations when the
When towing the vehicle, use only the vehicle is being towed. This safety switch A is located in the
attachment point provided for the towing
hook A which must be inserted into its
Do not tow the vehicle using a hook
attached to the suspension levers
passenger compartment, on the
underfloor, in front of the driver’s seat. In 2
seat B. the event of a collision, it deactivates the
WARNING

and wheel rims, but only onto the

• Take the towing hook A out of the fuel pump relays.
towing hook properly fitted in its
toolkit bag.
• Remove the cap C from its seat B.
seat.
Keep the ignition key in position II
Activation of this switch is indicated by
the illumination of the relative symbol on
the multi-function display (see page 86)
3
• Screw the hook tightly into its seat B. to allow the lights to work and to
and by activation of the hazard warning
prevent locking of the steering wheel
lights.
in the event of steering. Do not start
the engine when towing the vehicle. When the switch activates, the doors are
unlocked (if they were locked) and the
4
Keep in mind that the power steering central dome lights are turned on.
and brake servo will not be working The system can be reactivated by
when the engine is off. WARNING pressing the button on top of the
switch. 5
6
C A B �

•Position the gearshift lever in neutral

7
(“N” position for vehicles with “F1”
gearbox).

8
153
Battery master switch This operation, when the battery is
WARNING connected and fully charged, is done
It is located on the right-hand side of the automatically whenever the doors
luggage compartment. To access it, remove are opened or closed. The windows
the small door B. must remain lowered until the
recharged battery is reconnected. If
the battery is discharged and the
windows are fully up, only open the
doors when strictly necessary and
being extremely careful. Do not close
� them again until the windows can be
lowered.

We recommend that you use the

battery conditioner if the vehicle is not
used for long periods of time.
Disconnecting the battery
Before disconnecting the battery, Reconnecting the battery
deactivate the electronic alarm with the Fit the TORX T40 wrench into the switch
remote control. and turn it clockwise until it stops.
Never disconnect the battery from On every reconnection and before
Use the battery master switch to cut off WARNING the electrical system when the starting the engine, proceed as follows:
the power supply from the battery to the engine is running.
electrical system. - Close both the doors, and close the
Before disconnecting the battery, luggage compartment lid. Unlock and
To disconnect the battery, move the lower the side windows by at least lock the doors using the remote control.
switch anticlockwise using a TORX T40 0.78–1.18 in. (2–3 cm) to avoid Open the luggage compartment lid using
wrench. damaging the weather strips when the remote control.
The battery master switch must be opening and closing the doors. - Set the clock (date and time on control
WARNING used only if it is not possible to panel).
connect the battery conditioner.

154
 Advice for Emergency situations

- Close both the doors, raise the driver- • Visually inspect the outer casing for any
1
Checking the battery
side and passenger-side windows until cracks.
they meet the upper weather strip. The battery is positioned on the right-

2
• If the battery runs overloaded, it will
Check that the windows move down to hand side of the luggage compartment.
wear out quickly. Have the vehicle’s
the “upper limit” when the doors are electrical system checked if the battery
opened. tends to discharge easily.
Before starting the engine, wait at Keep the battery away from sources
WARNING least 60 seconds with the ignition
key at position II. This allows the
WARNING of heat and do not use open flames
or create sparks near it.
3
electronic system that controls the
motor-driven valves and the air con- Battery conditioner
ditioning ECU to perform their self-
learning cycles
During this time, do not to activate
The vehicle is equipped with a
conditioner for battery maintenance. 4
any device. Using the battery conditioner
contributes to extending the life of the
The Motronic ECU’s self-learning cycle is
successful when the intake air
temperature is above 41 °F
battery.
5
(5 °C). This device is housed in a pocket inside
the car cover bag, provided with the vehi-
After removing the battery from the
vehicle and disconnecting it from the
system through the battery master switch,
The vehicle is equipped with a battery
with sealed energy circuit, that is
maintenance-free.
cle. The socket for connecting the battery
conditioner is found on the right-hand
side of the luggage compartment, behind
6
when reconnecting make sure, before the panel B.
The battery does not need refilling
running the self-learning cycle, that the
with distilled water or sulphuric acid.
7
external air temperature is in the Arrange the battery conditioner in a
WARNING

indicated range. • Periodically check that the battery

WARNING well visible position, away from heat
terminals and posts are completely clean sources and children's reach.
and firmly secured.

8
155
 The vehicle cannot be started Exhaust system overheating
(ignition disabled) as long as the
alarm devices
WARNING

battery conditioner is connected to

the socket in the vehicle. In the event of irregular engine operation
and consequently high exhaust system
� Additional and extensive technical temperatures, the relative warning light will
information on the use of the device be displayed on the TFT display together
can be found in the manual provided with a warning message. The warning
inside the pocket of the car cover bag. message has two different alarm levels: high
temperatures or extreme temperatures.
The warning light display is controlled by
the thermoresistor, through the engine
ECU.

After connecting the battery conditioner

to the vehicle socket, run the connection
cable underneath the luggage compart-
ment lid, in the external/rear corner

Do not let the connection cable run

out of the vehicle, in positions other
than those indicated, to avoid
damaging the sealing gaskets and/or
the cable itself. Incorrect use of the vehicle could lead to
illumination of the TFT warning light.
If you do not plan on using the vehicle for
If the temperature is high (light
more than a week, we advise you to con-
flashing): The driver must decelerate
nect the battery conditioner in order to
WARNING

immediately to allow the temperature

preserve full battery efficiency.
of the exhaust system to decrease.

156
 Advice for Emergency situations

The electronic system detects and isolates

1
If the temperature is extreme (light on Replacing the brake pads and
steady): the error, preventing damage to the
WARNING

engine or the production of harmful brake discs

The temperature in the catalytic
converters has reached a dangerous
emissions. Brake pads
The brake pads are equipped with a wear
2
level and could damage them. If you
sensor, connected to the brake warning
continue to drive, the engine ECU will � light. When this warning light comes on
cut off the fuel supply to the injectors.
The driver must stop the vehicle and
turn off the engine so the exhaust
or, whenever braking no longer appears to
be regular, the pad thickness and the
condition of the braking surfaces must be
3
system can cool down. After about checked.
five minutes, restart the engine and

4
The minimum thickness allowed for the
drive normally.
pads is 0.12 in./3 mm (thickness of the
If the OBD warning light illuminates friction material only).
(see page 157) at the same time, it is
necessary to contact an Authorized
��� Pad replacement

5
Ferrari Dealer to check the control
unit’s memory for errors. The brake failure warning light will
Ferrari is not liable for any damage ��� illuminate to indicate excessive wear of
the brake pads, which must be replaced
to property or personal injury arising
immediately.
from failure to comply with the ��
When the warning light “Engine
warnings stated above. WARNING control system failure” illuminates,
engine performance may be
In order to help ensure the quality of
the components and accurate
WARNING

installation, we recommend that you

6
Engine malfunction alarm considerably reduced. have the procedure performed by your
devices Drive carefully, avoiding sudden Authorized Ferrari Dealer.
If the “engine control system failure” A
warning light flashes or is permanently lit
accelerations and high speeds.
Contact an Authorized Ferrari
To help ensure proper breaking-in of
the pads following replacement, avoid
sudden and sharp braking until the
7
when the engine is running, the engine or Dealer immediately.
emission control systems may be new pads have been run-in, after
about 186 mi (300 km).

8
malfunctioning.

157
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
Warranty and Service Book
Maintenance
Level checks
Wheels and tires
Care of the seat belts
and pretensioners
Cleaning the vehicle
If the vehicle is stored
for long periods
Warranty and Service Book Maintenance schedule The chassis therefore has technological
All the maintenance and checks indicated and manufacturing specifications that
The vehicle comes equipped with a require that any operation be performed
in the “Warranty and Service Book” must
“Warranty and Service Book”. by staff specially trained to work with this
be performed at an Authorized Ferrari
This contains the vehicle’s warranty Dealer at the prescribed intervals. innovative technology.
validity conditions. It is of crucial importance to use
It is however advisable to immediately
The Warranty and Service Book also report to your Authorized Ferrari Dealer equipment tested by Ferrari if the repair
WARNING contains special blank spaces where any small fault which may occur during work is to be performed in accordance
the Authorized Ferrari Dealer can use of the vehicle (e.g., small fluid leaks) with rules of good workmanship. Proper
register the regular maintenance and not to wait until the next service is execution of repair work ensures that the
services performed, as indicated in due to correct the problem. commercial value of the vehicle is
the maintenance schedule. preserved and the safety standards are
It is required to have the periodic
complied with.
maintenance services performed at least
Maintenance once a year, even if the specified mileage If the chassis is damaged as a result of
limit has not been reached (see an accident, Ferrari recommends that
It is essential to always keep the vehicle in “Maintenance Schedule” in the “Warranty you contact your Authorized Ferrari
proper working order to ensure a long and Service Book”). Dealer
working life and to prevent any running
defects, caused by negligence or lack of
Chassis and bodywork maintenance We recommend that you use original
maintenance, and consequently to avoid
hazardous situations. The vehicle chassis is entirely made of genuine Ferrari parts, which can be
aluminium, and has been designed using obtained from your Authorized Ferrari
All repair work on any component of the technology referred to as “Space Dealers.
the safety system must be performed Frame”. The chassis, under standard conditions of
by the Authorized Ferrari Dealer. use, requires no maintenance; it is
however advisable to contact your
Authorized Ferrari Dealers. at the
intervals indicated in the “Warranty and
Service Book” in order to have it checked.

160
 Care of the Vehicle

1
Level checks C Run the engine at idle for 2 minutes, then E If the oil level is too low, unscrew the cap 2
(without turning the engine off) check the on the tank and top up with the
oil level. recommended oil. Keep the oil level
The level checks must be performed at
the intervals indicated in the “Warranty
and Service Book” or, in any case, WARNING
If the oil level is not checked within 3
minutes (instead of 2 minutes, as indicat-
between the MIN and MAX notches. Screw
the cap 2 back on tightly. 2
before starting a long journey. ed above), repeat steps B and C before
checking the level.
If the oil level is below the “MIN”
notch, top it up and then have the
3
WARNING

D Remove the dipstick 1 from the sump and system checked by your Authorized
All the materials used for the check the level: this must be between the Ferrari Dealer.
following operations (e.g, cloths MIN and MAX notches on the dipstick.
soaked with oil or grease, pans, etc.) F Run the engine at 4500 RPM for 1 minute.
must be disposed of in compliance
with local environmental protection
regulations.
G Run the engine at idle for 2 minutes, then
(without turning the engine off) check the
oil level.
4
Open the engine compartment lid. � As the first check was performed within

We recommend that you use only

lubricants and/or fluids recommended
WARNING a time range of 2-3 minutes, the second
oil check must also be performed within
the same time range.
5
by Ferrari (see the “Recommended � For instance, if the first check was per-
lubricants and fluids” table). formed after 2 min. and 30 sec., the sec-
bar
1.4

A87
8
ond check must also be performed after
approximately 2 min. and 30 sec..
6
Engine oil
H Remove the dipstick 1 from the sump and
check the level: this must be between the
Proceed as follows:
A Run the engine at idle until reaching an
engine oil temperature ranging from 185 to
MIN and MAX notches on the dipstick.
Screw the cap 2 back on tightly.
7
194°F (85 - 90°C). Difference between MAX and MIN = 0.4 Top up the oil with care to avoid
US Gallon (1.5 liters). spilling it from the filler neck.
B Run the engine at 4500 RPM for 1 minute.
8
161
Gearbox and F1 gearbox system oil • Slowly pour in the indicated quantity of
coolant through the expansion tank filler
We recommend that you have the oil neck, until the fluid comes out from the
level checked by your Authorized open bleeder on the radiator. Reconnect
Ferrari Dealer or by skilled staff. the radiator bleeder pipe and complete
the filling procedure until reaching the
Max. level. If water comes out of the
Coolant heater pipe, close the cap.
• Close the bleeder cap on the heater
This procedure must always be pipe.

A87
performed when the engine is cold.

8
bar
1.4

�
WARNING

• Close the filler neck cap.

Never remove the cap C from the
expansion tank when the engine is • Turn on the heater by selecting the Max.
running or hot. temperature for the air conditioning and
heating system.
• Remove the cap C from the expansion • Start the engine and let it idle.
tank in the engine compartment and
• Slowly open the filler cap and top up
check that the level is at approximately Filling the circuit
until the fluid is visible in the filler neck
1.57 in. (40 mm) from the top of the To fill the circuit (this operation must be and until the radiator cooling fan
filler neck. performed when the engine is cold), activates.
• If the level is low, fill it up with the proceed as follows:
• Check that all the vents are blowing hot
recommended fluid. • Detach the bleeder pipe on the radiator air, at the same temperature ~ 122° F
and hold it lifted, so that it is at the (~50 °C).
If frequent refills are required after
same height as the filler neck, in order
short trips, have the system checked by • After the coolant level in the filler neck
to prevent spilling.
your Authorized Ferrari Dealer. has stabilized, close the filler cap.
• Turn key to position II and select the
• Run the engine until it reaches 3000
maximum temperature on the air
RPM, wait one minute and then let it
• Screw the cap C back on tightly. conditioning and heating system.
idle.
• Completely unscrew the bleeder cap on
• Run the engine until it reaches
the heater inlet pipe.
3000 RPM, turn off the heater and, after

162
 Care of the Vehicle

one minute, bring it back to idle. Remove the cap D from the tank in the
1
• Stop the engine and let it cool down. engine compartment and check that the
level is between the MIN and MAX
• Check the level once again and, if
necessary, fill up as indicated above
(without bleeding).
notches on the dipstick.
The oil level must be checked with the
�
2
cap resting on the tank.
• Screw on the filler neck cap tightly.
Fill up if necessary with the
Hydraulic steering system oil
recommended oil up to the MAX level.
Screw the cap D back on tightly.
3
Never dispose of used fluid in the
environment.

� Brake/clutch oil
4
• Check that the fluid in the tank is near
the MAX level.
• If the level is low, unscrew the cap E and
fill up with the recommended oil, taken
WARNING
The oil contained in the brake and
clutch systems, in addition to 5
from a sealed container. damaging plastic, rubber and
painted parts, is highly dangerous if
Never dispose of used fluid in the it comes into contact with the eyes
environment. or the skin.
In case of contact, wash the affected
6
part thoroughly with running water.
To avoid any risk, always use
The level check must be performed with
the engine warm, after having driven at
protective goggles and gloves.
Keep out of children’s reach! 7
least 9 miles (15 km), and with the On vehicles equipped with “F1” gearbox,
vehicle parked on flat ground. the tank supplies the braking system only.

8
163
The symbol on the tank cap indicates that How to use the tires
the system contains synthetic fluid.
This is a high performance vehicle. The
The use of mineral-based fluids will
wear of the tires will depend
WARNING irreparably damage the system
� significantly on your driving habits and
rubber gaskets.
patterns.The tires must be constantly
Do not use fluids other than those kept in good condition help ensure
already contained in the system for safe driving. Check regularly for wear
refills. and damage.
• When the system has been refilled,
screw the cap back on. The inflation pressure must correspond to
the specified values and must be checked
only when the tires are cold. Tire pressure
Windshield washer fluid increases as the tire temperature
The tank for the windshield wipers and progressively increases.
washer fluid can be accessed by lifting the Never reduce the pressure if the tires are
engine compartment lid. hot.
• Lift the cap F and fill the tank with the Insufficient tire pressure can lead to
recommended fluid (see the Wheels and tires
overheating, damage and even destruction
“Recommended Lubricants and Fluids” To help ensure performance, endurance of the tires.
table on page 30) until it can be seen in and the best tire adjustment on the wheel,
the filling manifold. Inflating the tires to a pressure
it is important to comply with the WARNING differing from that prescribed (see
• Close the cap. following instructions for the first 124– table on page 26 - 27) will render
186 mi. (200–300 km) with new tires: the monitoring system inefficient.
• avoid sudden accelerations Periodically check the tire pressure.
• avoid sharp braking and steering
• drive at moderate speed on straight
roads and on curves.

164
 Care of the Vehicle

Sudden impacts against sidewalks, holes in The tires are of the “directional” type
1
the road and other obstacles of various types, Your Authorized Ferrari Dealer have WARNING and there is an arrow marked on
as well as long trips on rough roads, can the necessary equipment for tire
their side to indicate the direction in
cause damage to the tires that may not
always be visible.
replacement.
Have the tires replaced by your
which they must rotate or which side
is the outer side. In the case of
2
Check the tires regularly for any signs of Authorized Ferrari Dealer, who has replacement, the best performance
damage (e.g., scratches, cuts, cracks, bulges, the required tools and equipment in levels can only be provided if the
order to avoid that improper or
etc.).
If sharp objects penetrate the tires, they can
careless operations damage the sensor
inside the wheel.
rotation direction corresponds with
the direction indicated by the arrow.
Tires on the same axle must always
3
cause damage which is only visible when the
tire is removed. be replaced in pairs.
Have any damage inspected by a qualified Your Authorized Ferrari Dealer can
technician as it may considerably reduce tire
life.
certify whether aged tires are suitable
for use. In any case, tires that have
Regularly check the tire tread (minimum
acceptable depth 0.067 in (1.7 mm). As 4
remained on a vehicle for more than the tread wear increases, there is a greater
Remember that tires deteriorate over time, risk of skidding.
3 years must be checked by an
even if they are rarely used or not used at all.
Cracks in the tread and side walls, possibly
accompanied by bulging, are sure signs of
Authorized Ferrari Dealer.

We recommend that you replace the WARNING

Drive carefully on wet roads to
reduce the risk of “aquaplaning”.
5
aging. WARNING tires when worn to a depth of less
Wheel with REVERSE RIM (HGTE than 0.067 in (1.7 mm), but in no Wheel alignment check and adjustment
������� package).
The tire must be fitted and removed
case should they be kept on the
vehicle for more than four years,
even if sufficient tire tread remains.
When you notice unusual wear of the tires
and, in any case, at the intervals
6
from the inner part of the rim only prescribed in the “Warranty and Service
Frequent use in maximum load
to avoid damaging the rim and Book”, have your Authorized Ferrari
conditions and at high temperatures
7
pressure sensor! Dealer check the wheel alignment.
may accelerate aging.
This operation must be performed
by skilled staff. Never fit tires of uncertain origin.
Contact your Authorized Ferrari
Dealer.
8
165
Maintenance of the seat belts Cleaning the vehicle without removing dirt or mud completely
can damage the bodywork.
and pretensioners Cleaning the exterior
• The vehicle must be washed regularly
• Periodically check that the screws on the All the materials used for the with suitable equipment. Do not use
anchoring points are tight and that the following operations (e.g., cloths very hot water or steam to clean the
seat belt is in proper condition and slide soaked with oil or grease, pans, etc.) paintwork and the lower surfaces. It is
smoothly. must be disposed of in compliance advisable to soften any dirt first, then
• The seat belt must be kept clean; the with the environmental protection remove it with a jet of water at room
presence of any dirt could jeopardize regulations. temperature.
the efficiency of the seat belt retractor. Proper care of the vehicle on the part of Do not use aggressive substances to
• To clean the seat belt, wash it by hand the owner is essential for the vehicle long WARNING clean the windows. Using aggressive
with mild soap and water and let it dry. life. substances may damage some parts
Do not use strong detergents, bleach or of the body.
Below is a list of the main precautions to
aggressive solvents, as they can weaken be taken.
the fibers. • Do not wash the vehicle in direct
• Certain parts of the vehicle should not be sunlight or when the bodywork is still
• Do not let the seat belt retractors get left wet or dirty for long periods of time: warm: ensure that the jet of water does
wet: they will function properly only if in particular, the passenger compartment not hit the paintwork too hard. Wash the
they are kept dry. floor and the luggage compartment must vehicle with a sponge and a solution of
• The pretensioner requires no always be kept clean and dry. The mild soap and water. Rinse the vehicle
maintenance or lubrication. If immersed draining holes under the doors should be again with a jet of water and dry it with
in water or mud, the pretensioner must kept unclogged to allow any water to a piece of chamois leather.
be replaced. drain. When the vehicle has been washed,
• The pretensioner must be replaced at • The underbody and the lower surfaces of WARNING apply slight pressure to the brake
the intervals indicated in the “Warranty the vehicle should be cleaned regularly, pedal at moderate speed before
and Service Book”. and more frequently (at least once a driving at a normal speed, until the
All work on any part of the safety week) if the vehicle is used on salty or brake discs and pads have cleaned off.
WARNING system components may only and rough roads. The vehicle should be
exclusively be performed by an cleaned thoroughly and carefully: In order to maintain the shine of the
Authorized Ferrari Dealer. cleaning that only wets the vehicle, paintwork, polish it once or twice a year
with the products recommended by Ferrari.

166
 Care of the Vehicle

• Any areas that are cracked or chipped as These products can be ordered through • bring the tire pressure to 43.5 psi
1
a result of stones, scratches or parking the Ferrari Spare Parts Department, (3.0 bar) and periodically change the
maneuvers, etc., must be immediately both individually and as part of the “Care tire resting point on the ground
repaired by an Authorized Ferrari
Dealer.
Kit” which includes the complete range of
products for cleaning the vehicle.
• disconnect the battery from the system 2
• Do not park the vehicle in damp and/or If you do not wish to disconnect the
For use of the “Care Kit” products, battery in order to keep certain devices
unventilated areas for long periods of
contact your Authorized Ferrari
time.

Carbon parts
Dealer.
functioning, such as the alarm system,
etc., the battery must be recharged at
least once a month. If the vehicle is not
3
Have small scratches and marks on the The following products must be avoided used for long periods of time with the
carbon structure removed by an when cleaning the leather: harsh battery disconnected, the battery must
Authorized Ferrari Dealer only.
Improper operations may irreparably
detergents, turpentine, liquid stain
removers, benzene, solvents and domestic
be recharged at least every three
months. 4
cleaning products. All of these products
damage the carbon parts.
damage the natural material. • protect the vehicle with a breathable
Do not use aggressive organic substances,
such as: gasoline, kerosene, petroleum,
acetone or solvents. If the vehicle is stored for long
fabric cover, avoiding materials that
would prevent any dampness on the
bodywork from evaporating.
5
periods Before using the vehicle again after long
Cleaning and care of the leather upholstery
If the vehicle is not used for long periods periods of inactivity, adjust the tire
As indicated in the “MAINTENANCE
SCHEDULE” (see “Warranty and Service
of time, it is advisable to take certain
precautions:
pressure to the indicated pressure and
check the fluid levels of all the systems.
6
Book”), proper and regular treatment, at
least once a year, will help preserve the • if possible, park the vehicle on a level
quality, natural characteristics and softness surface, in a covered and well-ventilated
of the leather upholstery in your Ferrari.
With this in mind, specific leather care
area
• keep the vehicle stationary by engaging
7
products are also available (“cleaner” and a gear and do not use the handbrake
“cream”) both tested by Ferrari.

8
167
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
Warning notes
Extreme caution required Subject Page ref.

Because of the high power generated by the engine, we recommend that the vehicle only be Introduction Page 4
used by experienced drivers.
The vehicle is equipped with emission control and monitoring systems, which must always Introduction Page 7
function properly.
Engine exhaust, some of its constituents, and certain vehicle components contain or emit Introduction Page 7
chemicals known to the State of California (CA) to cause cancer and birth defects and
reproductive harm. In addition, certain fluids contained in vehicles and certain products of
component wear contain or emit chemicals known to the State of CA to cause cancer and birth
defects or other reproductive harm. Battery posts, terminals and related accessories contain lead
and lead compounds. Wash your hands after handling. Used engine oil contains chemicals that
have caused cancer in laboratory animals. Always protect your skin by washing thoroughly with
soap and water.
General
Make sure you record the code numbers in the space provided in the “Warranty and Service Book”. Vehicle keys Page 12

The code numbers on the CODE CARD must always be kept in a safe and protected place, not Vehicle keys - Key codes Page 12
accessible to others.
We remind you that the emergency start procedure can only be performed using the Vehicle keys - Key codes Page 12
electronic code found on the CODE CARD.

Each key supplied has its own specific code, which must be stored in the memory of the The Ferrari CODE system Page 14
system ECU.
Contact your Authorized Ferrari Dealer immediately to have all the keys stored in the The Ferrari CODE system Page 14
system memory.

There is risk of explosion if the battery is replaced with an incorrect type. Dispose of used Replacing radio operated Page 14
batteries according to the instructions. control battery

170
 Table of Notes

Extreme caution required Subject Page ref.

1
Max. speed 149 mph - 240 km/h. Wheels and Tires Page 27
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and
does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Wheels and Tires Page 28 2
The temperature grade for this tire is established for a tire that is properly inflated and not Wheels and Tires Page 28
overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in
combination, can cause heat buildup and possible tire failure. 3
Observing the recommended wheel alignment values is essential in order to obtain the best Wheels and Tires Page 29
performance and the longest life of these tires. More information on these tires and on the relative
pressure monitoring system can be found in the “Carrozzeria Scaglietti” Owner’s Manual.

If you are going to use standard tires on a vehicle that was originally equipped with “Run
Flat” tires, you must contact your Authorized Ferrari Dealer to have the dashboard
Wheels and Tires Page 29 4
reprogrammed and to prevent viewing warning messages on the TFT display.

Ferrari urges you to use the seat belts correctly fastened and adjusted at all times!
Safety
Seat belts Page 34
5
Correct use of the seat belts can help reduce the risk of serious injury in the event of an Seat belts Page 34
accident.
All passengers must wear their seat belts!. Seat belts Page 34
6
Do not pass the seat belts over sharp edges. They could tear. Seat belts Page 34

Do not attach or pin anything onto the seat belts. This could reduce their initial strength
and cause them to tear in the event of a crash.
Seat belts Page 34
7
8
171
Extreme caution required Subject Page ref.

Do not bring cutting edges in contact with a seat belt. They may get damaged and Seat belts Page 34
consequently break in the event of a collision. If a seat belt has been brought in contact with
a cutting edge, or has been used to pin something on it, have it immediately replaced at your
Authorized Ferrari Dealer.
Do not allow children to be held on a passenger’s lap using only one seat belt for both of Seat belts Page 36
them. In the event of a crash, the weight of the adult would crush the child against the seat Fastening the seat belts
belt. This can result in serious injuries or death for the child.
After activation, the pretensioner no longer functions and cannot be repaired, under any Seat belts Page 37
circumstances. Contact your Authorized Ferrari Dealer for replacement. Pretensioners

All work on any part of the safety system components must be performed only by an Seat belts Page 37
Authorized Ferrari Dealer. Pretensioners

Never drive with a child in a rearward-facing child seat in the front seat if the "PASSENGER Child safety Page 37
AIRBAG OFF" warning light is not illuminated. Airbag deployment can cause serious
injuries or death to a child in a rearward-facing child seat.

Established legislation in some countries already provides that children under 12 years of Child safety Page 37
age may not travel in the front passenger seat.
Child seats may only be installed with the seat fully lowered and pushed backward. Child safety Page 37
Incorrect fastening of a child restraint system increases the risk of injury to the child in the Child safety Page 37
event of a collision.

Always deactivate this feature prior to using the seat belt for normal use. Having the retractor Child safety Page 38
locked can be dangerous when the seat belt is used for directly restraining a passenger.

Installing a child seat with the key in position II can result in induced injuries. Child safety Page 38

172
 Table of Notes

Extreme caution required Subject Page ref.

1
Never drive with a child in a rearward-facing child seat in the front seat if the Child safety Page 39
"PASSENGER AIRBAG OFF" warning light is not illuminated. Airbag deployment can
cause serious injuries or death to a child in a rearward-facing child seat. 2
Never carry a child in a adult’s lap. In the event of a crash, the weight of the adult could crush Child safety Page 39
the child against the seat belt (or the dashboard). This could result in serious injuries or death
for the child.
This is a high-performance vehicle. You are strongly urged not to carry children in this Child safety Page 39
3
vehicle, since they can also be injured by hard accelerations.
Always drive slowly and carefully when carrying a child. Hard accelerations due to sport- Child safety Page 39
style driving can be dangerous for children, even if no crash occurs.
4
Children must always be seated in a child restraint system specifically designed for their size, Child safety Page 40
and must be properly restrained.

Unrestrained occupants, including children, can be propelled against the dashboard or the
windshield by hard braking and by crash forces. This can result in serious injuries or death.
Child safety Page 40
5
Do not tamper with seat belts or child restraint systems. Child safety Page 40

The ignition key must always be turned to position 0 when installing a child seat on the front
passenger seat.
Child safety Page 40 6
The advanced airbag system of your vehicle is not designed to protect adults with disability Child safety Page 40
that require deactivation of the passenger’s or driver’s airbag. Transport of person with

If you or another occupant is an adult with a medical condition that requires airbag
disability

Child safety Page 40

7
deactivation, please contact your Authorized Ferrari Dealer. Transport of person with
disability

8
173
Extreme caution required Subject Page ref.

As long as the airbag is activated, persons with disability are advised not to travel in the Child safety Page 40
vehicle in order to avoid the risk of serious injuries or death, even in minor crashes. Transport of person with
disability
The airbag is not a substitute for the seat belts. Correct use of the seat belts, in combination Airbag Page 41
with the airbag, will offer protection for the driver and passenger in the front seats in the
event of a head-on collision.
Front airbags cannot offer protection in side crashes, certain front-angular crashes, roll Airbag Page 41
over events or in secondary impacts (if a second crash happens after the airbags have been
deployed in a previous crash). The seat belts are designed to help reduce the risk of injuries
in roll over events and secondary front impacts. A properly fastened seat belt is needed to
help protect occupants in roll over events and secondary front impacts.
Front airbags are designed to not be deployed in low severity frontal crashes. The seat belts Airbag Page 41
can help reduce injuries in low severity crashes. A properly fastened seat belt is needed to
help protect the occupants in low severity frontal crashes.
When the ignition key is turned to position II, the warning light C illuminates. If no Airbag Page 41
malfunctioning is detected, it will go off after 4 seconds. If the warning light does not Airbag system components
illuminate, if it remains on or if it illuminates while driving, contact your Authorized Ferrari
Dealer immediately.
The driver and passenger are both advised not to travel handling objects (e.g., beverage cans Airbag Page 42
or bottles, pipes, etc.) that could cause injury in the case of airbag deployment. Operation

Always drive with your hands on the rim of the steering wheel so that, in case of activation, Airbag Page 42
the airbag can deploy without obstruction. Driving with your hands inside the steering Operation
wheel rim or on the airbag cover increases the risk of injury for your wrists and arms.

The driver and passenger must always fasten their seat belts and sit in an upright position, as Airbag Page 42
far as possible away from the airbag, in order to help ensure protection in all types of collision. Operation

174
 Table of Notes

Extreme caution required Subject Page ref.

1
Always keep the backrest of your seat in the upright position and sit with your back properly Airbag Page 42
resting against it.
With the ignition key inserted and in position II, although the engine is off, the airbags can
Operation
Airbag Page 42
2
still be activated when the vehicle is stationary if it is hit by a moving vehicle. Thus, even with Operation
the vehicle stationary, do not put children in the front seat. In addition, remember that if
the ignition key is in position 0, none of the safety devices (airbags or pretensioners) will be
activated in the event of a collision. Failure of the airbags to inflate in these circumstances is 3
not indicative of a system malfunction.
Therefore, even with the vehicle stationary, do not allow children to sit on the front seat. Airbag Page 42

Never place an object over or near the airbag covers. In the event that the airbags are
Operation
Airbag Page 43 4
deployed, these objects would be projected into the passenger compartment at very Operation
high speed. The object will be transformed into a projectile propelled in the passenger
compartment. This could cause serious injuries.
Never modify the airbag modules. Do not damage the airbag modules (for example pinning
something onto them or pressing objects against their covers). If, for any reason, an airbag
Airbag
Operation
Page 43 5
cover gets damaged, have the airbag module immediately checked by your Authorized
Ferrari Dealer. Activation of a damaged module could cause serious or fatal injuries.

Damaged or defective components of the airbag system cannot be repaired and must be
replaced. Improper operations performed on the system components may cause failures or
Airbag
Operation
Page 43 6
accidental deployment of the airbags with consequent damage and injury, even fatal.
The airbag modules must be replaced at the intervals indicated in the “Warranty and Service Airbag Page 43
Book” EVEN if the vehicle was NOT involved in a collision.
The airbags are not a substitute for the seat belts. Correct use of the seat belts, with the
Operation
Side Airbag Page 44
7
supplementary action of the side bags, will provide protection in the event of a lateral collision.

8
175
Extreme caution required Subject Page ref.

The side bag fitted on the vehicle was not designed to reduce the risk of being hurled out Side Airbag Page 44
in the event of vehicle roll-overs. Side bag system components

When the ignition key is turned to position II, the warning light B will illuminate. If no Side Airbag Page 44
malfunctioning in the airbag system is detected, it will go off after 4 seconds. If the warning Side bag system components
light does not illuminate, if it remains on or if it illuminates while driving, contact your
Authorized Ferrari Dealer immediately.
Never travel with your head leaning out of the window, as your head and neck would be in the Side Airbag Page 45
airbag activation area. In the event of a side collision, this position would increase the risk of Operation
being hurled out of the vehicle and would compromise the protective action of the side bags.

Never place an object over or near the airbag covers. In the event that the airbags are Side Airbag Page 45
deployed, these objects would be projected into the passenger compartment at very Operation
high speed. The object will be transformed into a projectile propelled in the passenger
compartment. This could cause serious injuries.
Never modify the airbag modules. Do not damage the airbag modules (for example pinning Side Airbag Page 45
something onto them or pressing objects against their covers). If, for any reason, an airbag Operation
cover gets damaged, have the airbag module immediately checked by your Authorized
Ferrari Dealer. Activation of a damaged module could cause serious or fatal injuries.

Following activation, the airbag components can no longer perform their protective action; Side Airbag Page 46
therefore, they cannot be repaired and must be replaced. After activation of a side bag, have Operation
it replaced by your Authorized Ferrari Dealer.

The airbag modules must be replaced at the intervals indicated in the “Warranty and Service Side Airbag Page 46
Book” EVEN if the vehicle was NOT involved in a collision. Operation
Do not carry adults in the front passenger seat if the “PASSENGER AIRBAG OFF” warning Advanced Airbag System Page 47
light is illuminated, as the passenger airbag will not deploy in a frontal crash, thus reducing
the system’s ability to protect the occupant.

176
 Table of Notes

Extreme caution required Subject Page ref.

1
Do not carry children in rearward-facing child seats in the front passenger seat if the Advanced Airbag System Page 47
“PASSENGER AIRBAG OFF” warning light is not illuminated, as the passenger airbag
could deploy in a frontal crash, seriously injuring or killing the child. 2
Never place an object over or near the driver’s or passenger’s airbags. In the event that the Advanced Airbag System Page 49
airbag is deployed, it will project any object over it, or near it, in the passenger compartment
at very high speed. The object will be transformed into a projectile propelled in the
passenger compartment. This could cause serious injuries. 3
Seat belts are designed to help minimize injury severity in the event of an accident. To help Advanced Airbag System Page 49
achieve optimal protection for adults, the airbags should supplement the seat belts. Always
wear your seat belts properly fastened.
Front airbags cannot offer protection in side crashes, certain front-angular crashes, roll
over events or in secondary impacts (if a second crash happens after the airbags have been
Advanced Airbag System Page 49 4
deployed in a previous crash). The seat belts are designed to help reduce the risk of injuries
in roll over events and secondary front impacts. A properly fastened seat belt is needed to
help protect occupants in roll over events and secondary front impacts.
Front airbags are designed to not be deployed in low severity frontal crashes. The seat belts Advanced Airbag System Page 50
5
can help reduce injuries in low severity crashes. A properly fastened seat belt is needed to help
protect occupants in low severity frontal crashes.
To help ensure protection in the event of a collision, you must be in a normal seated position
with your back against the seat backrest. The passenger’s feet must be on the footrest. The
Advanced Airbag System Page 50
6
driver’s left foot must be on the footrest.
Adjust your seat as far back as possible, ensuring you can operate the vehicle controls properly Advanced Airbag System Page 50
and comfortably. Keep your hands on the steering wheel rim, without crossing them. Placing
your hands or arms inside the rim increases the risk of hand/arm injuries in the event of a
crash with driver’s airbag deployment.
7
8
177
Extreme caution required Subject Page ref.

Never place your feet on the dashboard or the instrument panel or out of the window, as this Advanced Airbag System Page 50
will seriously affect the ability of the system to protect you in the event of a crash, and can
result in induced injuries in the event of airbag deployment.
Adults should not travel in the front passenger seat if the “PASSENGER AIRBAG OFF” Occupant Classification Page 51
warning light is illuminated. System
Children in a rearward-facing child seat must not travel in the front passenger seat if the Occupant Classification Page 51
“PASSENGER AIRBAG OFF” warning light is not illuminated. System
Installing a child seat with the ignition key in position II can result in induced injuries. Occupant Classification Page 51
System
Do not carry adults in the front passenger seat if the “PASSENGER AIRBAG OFF” warning Occupant Classification Page 53
light is illuminated, as the passenger airbag will not deploy in a frontal crash, thus reducing System
the system’s ability to protect the occupant.
Do not carry children in rearward-facing child seats in the front passenger seat if the Occupant Classification Page 53
“PASSENGER AIRBAG OFF” warning light is not illuminated, as the passenger airbag System
could deploy in a frontal crash, causing serious injury or death.
The front passenger’s seat and its control unit are part of the advanced airbag system. Never have Occupant Classification Page 53
your seat tampered with, as this can result in a system malfunction, which could cause serious System
injuries or death.
Repairs on the front passenger seat must only be performed by trained technicians at an Occupant Classification Page 53
Authorized Ferrari Dealer. System
Not following the above instructions can result in serious injuries or death in the event of a Advanced Airbag System Page 53
crash.
The ABS system features remain unaltered as long as the speed limit for the tire side grip is ABS Page 54
not exceeded. When this limit is exceeded, vehicle skidding cannot be avoided.

178
 Table of Notes

Extreme caution required Subject Page ref.

1
The ABS system does NOT exempt the driver from driving carefully and responsibly at all times. ABS Page 54

RACE mode must be used only on race tracks. CST Page 55 2

The system warns the driver that the tire pressure has decreased. However, this does NOT Tire pressure and temperature Page 56
exempt the driver from periodically checking that the tires are inflated to the indicated monitoring system
pressure. In addition, the system is UNABLE to warn the driver of sudden damage to the tires
caused by external objects/agents (e.g., nails, stones, etc.). 3
Before calibrating the system, make sure that the tire pressures correspond to the indicated Tire pressure and temperature Page 59
pressure values (see page 24-25). If this is not the case, the system may issue wrong low monitoring system
pressure indications. System not calibrated

About your
4
vehicle
Always check that the doors are properly closed to prevent them from opening while driving. Door opening and closing
Door locking and opening
from the inside
Page 68
5
Always check that the lid is properly closed to prevent it from opening while driving. Engine compartment lid Page 69
Closing
Always turn off the engine during refueling. Take extreme care when removing the cap. Do not
smoke or use open flames during refueling. The following can be harmful for your health:
Fuel tank door and cap open-
ing and closing
Page 71 6
- fuel coming into contact with your skin
- inhaling fuel vapors.

Improper use of the power windows can be dangerous. Before use, always check that people Power window opening and Page 73 7
and objects are at a safe distance. Pay particular attention during the automatic operation closing
of the driver-side power window. To protect the passengers remaining in the car against
accidental operation of the power windows, always remove the key from the ignition.
8
179
Extreme caution required Subject Page ref.

If the high beam control is on, the high beams will turn on every time the external lights Lighting Page 75
are activated automatically. We recommend therefore that you turn them off every time the Automatic activation and
twilight sensor deactivates the external lights. deactivation

In case of fog during the day, the position lights and low beams will not activate Lighting Page 75
automatically. The driver must always be ready to turn on the lights manually, and also the Automatic activation and
rear fog lights if necessary. deactivation

The driver is always responsible for turning on the external lights, depending on the Lighting Page 75
ambient light and in compliance with the regulations in force in the country of use. The Automatic activation and
automatic system for turning on and off the external lights must be considered an aid for deactivation
the driver. If necessary, turn the lights on and off manually.
RACE mode must be used only on race tracks. “TFT” display Page 81
Stop the vehicle avoiding hard braking. Do not drive further and contact an Authorized Instruments and gauges Page 88
Ferrari Dealer immediately. TFT display warning lights
The vehicle can still be driven at low speed (max. 25 mph – 40 km/h), to leave the road. Instruments and gauges Page 88
TFT display warning lights
In this condition, do not activate “SPORT” or "RACE" mode. Instruments and gauges Page 89
TFT display warning lights
Stop the vehicle avoiding hard braking. Do not drive further, check the fluid level in the tank Instruments and gauges Page 91
and immediately contact your Authorized Ferrari Dealer. Warning lights
Stop the vehicle avoiding hard braking. Do not drive further and immediately contact your Instruments and gauges Page 91
Authorized Ferrari Dealer. Warning lights

The vehicle can still be driven at low speed (max. 25 mph – 40 km/h), to leave the road. Instruments and gauges Page 91
Warning lights
Danger of rear wheels locking and risk of spinning. Stop the vehicle avoiding hard braking. Instruments and gauges Page 91
Do not drive further and immediately contact your Authorized Ferrari Dealer. Warning lights

180
 Table of Notes

Extreme caution required Subject Page ref.

1
The vehicle can still be driven at low speed (max. 25 mph – 40 km/h), to leave the road. Instruments and gauges Page 91

RACE mode must be used only on race tracks.

Warning lights
Instruments and gauges Page 96
2
Warning lights

Do not operate the windshield washer during the cold months until the windshield has
warmed up. If it has not warmed up, the liquid could freeze on the glass and block the view.
Windshield washer/wipers
and headlight washer
Page 98
3
Windshield washer
Before cleaning the front windshield (for example in service stations) make sure the rain sensor Windshield washer/wipers Page 99
is deactivated or that the key is at position 0. The rain sensor must be deactivated also when
washing the vehicle by hand or in automatic car washes. In case of ice or snow on the front
windshield, do not activate the rain sensor to avoid damaging the wiper motor and/or blades.
and headlight washer
Rain sensor 4
BEFORE YOU DRIVE Driving the vehicle Page 100
Check that the seat belts are fastened.
Check that the doors are closed.
5
Check that the seat is properly adjusted.
Check the rear-view mirror adjustment (center and sides).
Use unleaded fuel only! Using leaded fuel would permanently damage the catalytic converters. Driving the vehicle
Recommended lubricants and
Page 100 6
fluids
If the failure warning light continues flashing without going off, deactivate the system and Driving the vehicle Page 101
restart it. If the failure persists, contact an Authorized Ferrari Dealer to have the necessary
checks performed.
Starting and driving the
vehicle (F1)
7
System starting

8
181
Extreme caution required Subject Page ref.

If a horizontal dash appears on the display, there is a system failure. Driving the vehicle Page 101
Starting and driving the
vehicle (F1)
Operation with the engine off
Hold button R down, until the letter R appears on the display. Driving the vehicle Page 102
Starting and driving the
vehicle (F1)
Operation with the engine off
Hold the brake pedal down while starting the engine. Driving the vehicle Page 102
Starting and warming up the
engine (F1)
Use 1st gear for parking or for starting uphill. Driving the vehicle Page 103
Starting the vehicle (F1)
The buzzer may also sound to warn the driver that the clutch is starting to overheat. This Driving the vehicle Page 104
may occur if you use the accelerator pedal when the vehicle is stationary on a hill or during Starting the vehicle (F1)
the “pick-up” maneuver.
RACE mode must be used only on race tracks. F1 - SUPERFAST gearshifting Page 105
Do not start the vehicle before the display has turned off. Never leave the vehicle with the Driving the vehicle Page 106
gearshift in N. Engage a gear (1st or R), check that the display is not flashing and always Turning off the engine and
apply the handbrake. Never leave the vehicle with the engine running. the system (F1)

Never remove the key when the vehicle is moving! The system and the display will remain Driving the vehicle Page 106
active, but malfunctioning, until the vehicle is stopped. In addition, the steering wheel will Turning off the engine and
lock automatically with the first turn of the steering wheel. the system (F1)

Use 1st gear for parking or for starting uphill. Driving the vehicle Page 108
Starting the vehicle (CM)
When the engine has started

182
 Table of Notes

Extreme caution required Subject Page ref.

1
Continuing to drive when a red warning light is on could cause serious damage to the Driving the vehicle Page 109
vehicle and affect its operation and performance. After sports-style driving, let the engine
idle for several minutes before turning it off, in order to stabilize the temperatures.
While driving (CM)
2
Do not coast downhill with the engine off, as the servo brake will no longer function due to Driving the vehicle Page 109
the vacuum decrease and thus, after a less braking attempts, the system will become inefficient. While driving (CM)

Never leave children unattended in the vehicle. Do not park the vehicle on flammable materials
(e.g., paper, grass, dry leaves, etc.). They could catch fire if they come into contact with hot parts
Driving the vehicle
Parking
Page 109 3
of the exhaust system. Do not leave the engine running with the vehicle unattended.

To help ensure the system proper functioning, the sensors positioned on the bumper must Driving the vehicle Page 110
be kept clean (remove any mud, dirt, snow or ice).
However, the driver remains fully responsible for parking maneuvers and in other
Parking maneuver
Driving the vehicle Page 110
4
potentially dangerous situations. The system has been designed only as a supplementary aid Parking maneuver
during parking maneuvers, since it allows the driver to detect obstacles outside his field of
vision. Use of the sensors therefore does not mean that the driver can be less careful and
attentive and not watch out for persons and obstacles during parking maneuvers. 5
The driver is fully responsible for parking and other potentially dangerous maneuvers. Driving the vehicle Page 111
During these maneuvers, always make sure there are no people (especially children) or Parking maneuver
animals in the maneuvering area. The parking sensors must be considered an aid for the
driver who, in any case, must never take less care during potentially dangerous maneuvers,
even if they are performed at low speeds.
Failure warnings
6

7
8
183
Extreme caution required Subject Page ref.

Drunk driving, or driving under the influence of drugs, alcohol or certain medicines is extremely Driving the vehicle Page 112
dangerous for yourself and others. Traveling without your seat belt fastened increases the risk of Safe driving
serious injury and death in the event of a collision. Always fasten the seat belt and the child seat, When travelling
if any. Deactivate the passenger’s airbag (where possible) if a child seat is fitted on the front seat.
Do not travel with objects lying around on the floor, especially in front of the driver’s seat: in the
event of braking, these could slide under the pedals, making it impossible to brake or accelerate.
Additionally, ensure that any floor mats fit correctly. Water, ice and salt spread on icy roads may
deposit on the brake discs and reduce the efficiency of the initial braking.

If the road is wet, reduce your speed to avoid “aquaplaning” phenomena, during which the tire Driving the vehicle Page 113
no longer touches the road surface. This is due to the fact that, when the road is very wet and Safe driving
the vehicle speed is high, the side channels of the tire tread, because of their particular shape When travelling
or insufficient depth, are not capable of removing all of the water channelled, so that a layer of
water exists between the road surface and the tire. The fluid pressure generated is so high as
to support the vehicle’s weight, making it impossible for the driver to control the vehicle.

On stretches where visibility is good, turn off the rear fog lights, as they are very bright and Driving the vehicle Page 114
may be annoying for the occupants of the vehicles behind you. Safe driving
Driving in fog
RACE mode must be used only on race tracks. Ignition switch Page 116
Position II - Start
Never remove the key when the vehicle is moving! The steering wheel will lock automatically Ignition switch Page 116
with the first turn of the steering wheel. Always remove the key from the ignition when you Position II - Start
get out of the vehicle! Never leave children unattended in the vehicle.

Always apply the handbrake when the vehicle is parked. After hearing a series of clicks by Handbrake lever Page 117
pulling the handbrake lever, the vehicle should be blocked. If this is not the case, please
contact your Authorized Ferrari Dealer

184
 Table of Notes

Extreme caution required Subject Page ref.

1
Never adjust the seat while driving: you may lose control of the vehicle. Adjustments Page 118

Sitting in a reclined position while the vehicle is in motion could be dangerous. The
Seat adjustments
Adjustments Page 119
2
backrest should not be tilted too far back. The 3-point shoulder/lap belt must be firmly Seat adjustments
secured against the occupant’s body in order to function properly. Therefore, both the
driver and passenger’s backrests must always be in an upright position while the vehicle is
in motion; otherwise the 3-point shoulder/lap belt would not remain firmly secured against
the occupant’s body. Serious injury could result.
3
Do not adjust the steering wheel when the vehicle is moving. Adjustments Page 120
Steering wheel adjustment
Keep the glove compartment closed while driving. Passenger compartment
accessories
Page 126 4
Glove compartment

5
Do not use the cigarette lighter seat as a power socket for electrical items of any kind! The Passenger compartment Page 127
cigarette lighter reaches very high temperatures. Handle it with care to avoid risk of burns accessories
and fire. It is possible to connect the emergency tire repair and inflation kit ONLY for the Ashtray
time necessary for the operation.
Advice for Emergency
situations 6
In the event of repairs performed using the toolkit provided, you must: Advice for Emergency Page 130
- use suitable personal protection (e.g., gloves) situations
- take suitable precautions (e.g., when changing a tire, never lie under the vehicle raised on the
jack)
- have the basic and specific skills required for working with electrical parts/components.
7
8
185
Extreme caution required Subject Page ref.

After using the repair kit, the vehicle must however be considered to be in an emergency Toolkit Page 130
situation: drive with the utmost care (maximum permissible speed 50 mph – 80 km/h). The Emergency tire repair and
kit is to be used to temporarily repair only one tire punctured by small objects: the kit may inflation kit
not be useful in the case of large punctures or tearing.
Keep the kit in its box and out of children’s reach. Do not inhale or swallow the fluid Toolkit Page 131
contained in the cartridge and avoid contact with the skin and eyes. Tire inflation and repair kit
for emergency situations
The sealant contained in the cartridge in the tire repair kit may damage the sensor fitted inside Toolkit Page 131
the wheel rim on vehicles equipped with the tire pressure monitoring system. In these cases, Tire inflation and repair kit
always have the sensor replaced by an Authorized Ferrari Dealer. for emergency situations
If the jack is not positioned correctly, the vehicle could slip off. The jack supplied must only be Replacing a wheel Page 152
used for replacing the wheels. Replacing a wheel

Inflate the collapsible spare wheel before lowering the car, as otherwise the rims may Replacing a wheel Page 152
be damaged Replacing a wheel
The kit must be used in “tire inflation” mode. Replacing a wheel Page 152
Use lever terminal H. Replacing a wheel

The spare wheel is not equipped with the tire pressure monitoring sensor (see label on Replacing a wheel Page 152
spare wheel bag). After installation, it is not monitored by the system, but it does comply Replacing a wheel
with International Regulation ECE R64/01. Once fitted, we recommend you go to the
nearest Authorized Ferrari Dealer.
Always follow the applicable driving and traffic regulations when the vehicle is being towed. Towing hook Page 153

Do not tow the vehicle using a hook attached to the suspension levers and wheel rims, but Towing hook Page 153
only onto the towing hook properly fitted in its seat. Keep the ignition key in position II to
allow the lights to work and to prevent locking of the steering wheel in the event of steering.
Do not start the engine when towing the vehicle.

186
 Table of Notes

Extreme caution required Subject Page ref.

1
The system can be reactivated by pressing the button on top of the switch. Fuel inertia switch Page 153
Never disconnect the battery from the electrical system when the
engine is running. Before disconnecting the battery, lower the side windows by at least
Battery master switch Page 154 2
0.78–1.18 in. (2–3 cm) to avoid damaging the weather strips when opening and closing the doors.

3
This operation, when the battery is connected and fully charged, is done automatically whenever Battery master switch Page 154
the doors are opened or closed. The windows must remain lowered until the recharged battery is
reconnected. If the battery is discharged and the windows are fully up, only open the doors when
strictly necessary and being extremely careful. Do not close them again until the windows can be
lowered.
The battery does not need refilling with distilled water or sulphuric acid.

Keep the battery away from sources of heat and do not use open flames or create sparks near it.
Checking the battery

Checking the battery

Page 155

Page 155
4
Arrange the battery conditioner in a well visible position, away from heat sources and children's reach. Checking the battery Page 155

The vehicle cannot be started (ignition disabled) as long as the battery conditioner is
Battery conditioner
Checking the battery Page 156
5
connected to the socket in the vehicle. Battery conditioner
If the temperature is extreme (light on steady): Exhaust system overheating Page 156
The temperature in the catalytic converters has reached a dangerous level and could
damage them. If you continue to drive, the engine ECU will cut off the fuel supply to the
alarm devices
6
injectors.
The driver must stop the vehicle and turn off the engine so the exhaust system can cool
down. After about five minutes, restart the engine and drive normally.
If the OBD warning light illuminates (see page 157) at the same time, it is necessary to
7
contact and Authorized Ferrari Dealer to check the control unit’s memory for errors.
Ferrari is not liable for any damage to property or personal injury arising from failure to
comply with the warnings stated above.
8
187
Extreme caution required Subject Page ref.

When the warning light “Engine control system failure” illuminates, engine performance Engine malfunction alarm Page 157
may be considerably reduced. Drive carefully, avoiding sudden accelerations and high devices
speeds. Contact an Authorized Ferrari Dealer immediately.

In order to help ensure the quality of the components and accurate installation, we recommend Replacing the brake pads and Page 157
that you have the procedure performed by your Authorized Ferrari Dealer. To help ensure brake discs
proper breaking-in of the pads following replacement, avoid sudden and sharp braking until the Replacing the brake pads
new pads have been run-in, after about 186 mi (300 km).
Care of the Vehicle
The Warranty and Service Book also contains special blank spaces where the Authorized Warranty and Service Book Page 160
Ferrari Dealer can register the regular maintenance services performed, as indicated in the
maintenance schedule.

If the oil level is not checked within 3 minutes (instead of 2 minutes, as indicated above), repeat Level checks Page 161
steps B and C before checking the level. Engine oil
If the oil level is below the “MIN” notch, top it up and then have the system checked by your Level checks Page 161
Authorized Ferrari Dealer. Engine oil
As the first check was performed within a time range of 2-3 minutes, the second oil check must Level checks Page 161
also be performed within the same time range. Engine oil
For instance, if the first check was performed after 2 min. and 30 sec., the second check must also
be performed after approximately 2 min. and 30 sec..
This procedure must always be performed when the engine is cold. Never remove the cap C Level checks Page 162
from the expansion tank when the engine is running or hot. Coolant

The oil contained in the brake and clutch systems, in addition to damaging plastic, rubber Level checks Page 164
and painted parts, is highly dangerous if it comes into contact with the eyes or the skin. In Brake/clutch fluid
case of contact, wash the affected part thoroughly with running water. To avoid any risk,
always use protective goggles and gloves. Keep out of children’s reach!

188
 Table of Notes

Extreme caution required Subject Page ref.

1
The use of mineral-based fluids will irreparably damage the system rubber gaskets. Do not Level checks Page 164
use fluids other than those already contained in the system for refills. Brake/clutch fluid
2
Inflating the tires to a pressure differing from that prescribed (see table on page 28) will Wheels and tires Page 165
render the monitoring system inefficient. How to use the tires
We recommend that you replace the tires when worn to a depth of less than 0.067 in (1.7
mm), but in no case should they be kept on the vehicle for more than four years, even
if sufficient tire tread remains. Frequent use in maximum load conditions and at high
Wheels and tires
How to use the tires
Page 165
3
temperatures may accelerate aging.
The tires are of the “directional” type and there is an arrow marked on their side to indicate Wheels and tires Page 165
the direction in which they must rotate or which side is the outer side. In the case of
replacement, the best performance levels can only be provided if the rotation direction
How to use the tires
4
corresponds with the direction indicated by the arrow. Tires on the same axle must always be
replaced in pairs.
Drive carefully on wet roads to reduce the risk of “aquaplaning”. Wheels and tires
How to use the tires
Page 165
5
All work on any part of the safety system components may only and exclusively be Maintenance of the seat belts Page 166
performed by an Authorized Ferrari Dealer. and pretensioners

Do not use aggressive substances to clean the windows. Using aggressive substances may
damage some parts of the body.
Cleaning the vehicle
Cleaning of the exterior
Page 166 6
When the vehicle has been washed, apply slight pressure to the brake pedal at moderate speed Cleaning the vehicle Page 166
before driving at a normal speed, until the brake discs and pads have cleaned off. Cleaning of the exterior
7
8
189
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
Glossary
192
 Glossary

1
Abbreviation Meaning
ABS The ABS system is designed to prevent wheel locking during braking and helps the driver to maintain full

A.C.
steering control over the vehicle.
Air Conditioning.
2
ASR Anti-skid regulation during acceleration.
AUTO easy
exit
AUTO easy exit mode. To exit the “AUTO easy exit” mode, shift one of the two gearshift levers.
3
Traction Force transmitted by the vehicle to the road surface through the wheels; it indicates the grip.
power

CST Traction Stability Control. 4

“TFT” display Thin Film Transistor display on the instrument panel, that shows information about the control system.
ECU Electronic Control Unit.
Xenon
headlights
The Xenon headlights produce a brighter light beam and use a voltaic arc instead of an incandescent filament.
5
F1 Electronically-controlled gearbox, designed with the same technology as used in the racing sector.

6
F1-Trac Traction control derived from the technologies used in the racing sector.
OBD On-Board Diagnostic system.
VDC Vehicle dynamics control using the braking system and engine torque.

7
8
193
1. General

2. Safety

3. About your Vehicle

4. Advice for Emergency Situations

5. Care of the Vehicle

6. Table of Notes

7. Glossary

8. Index
Index
 Index Checking the hydraulic steering E
oil level .......................................................... 163 Electrical system .......................................... 26
Child safety .................................................... 37 Electronic alarm .......................................... 16
Cleaning the vehicle ................................ 166 Electronic speedometer ............................ 90
A Clothing hooks .......................................... 127 Emergency starting .................................... 15
Consulting the Manual ................................ 4 Engine compartment lid .......................... 69
Abbreviations/Meanings ............................ 5
Coolant .......................................................... 161 Engine malfunction alarm devices .... 157
ABS ................................................................... 54
CST ................................................................... 54 Engine oil temperature gauge ............... 92
Adjusting the seat belt height ............... 34
CST OFF mode ........................................... 96 Engine pressure gauge ............................. 92
Adjusting the steering wheel ............... 120
Environmental protection .......................... 7
Air conditioning and D Exhaust system overheating
heating system ............................................. 122
alarm devices .............................................. 155
Airbag .............................................................. 41 Dimensions and weights .......................... 23
External rear-view mirrors .................... 121
Alarm system .................................................. 12 Direction indicators ................................... 76
Ashtray ............................................................ 127 Doors ................................................................ 68 F
“AUTO easy exit” mode........................... 107 “DOWN” gearshift lever .......................... 97
“Automatic gearshift” mode ................. 106 Driver’s seat position memory ............. 119 F1 – SUPERFAST gearshifting ........... 105
Driver-side power window ..................... 72 Fastening the seat belts ............................ 35
B Driving at night .......................................... 113 Filling the cooling circuit ...................... 162
Driving in fog ............................................. 114 Fuel Consumption ...................................... 25
Battery master switch .............................. 153
Driving in the rain .................................... 113 Fuel inertia switch .................................... 153
Battery conditioner .................................. 155
Driving on mountain roads .................. 114 Fuel level gauge ........................................... 84
Before you drive ........................................ 112
Driving on snowy or icy roads ............ 114 Fuel tank cap and door .............................. 71
Body Computer fuses and relays ....... 142
Driving style ..................................................... 7 Fuses and relays in the engine
Driving the vehicle ..................................... 99 compartment ............................................... 141
C
Driving the vehicle Fuses and relays in the luggage
Chassis – Bodywork ................................ 160 (Mechanical Gearbox) ............................ 108 compartment ............................................... 149
Checking the brake/clutch Driving the vehicle (F1) ........................ 103 Fuses and relays in the passenger
fluid level ...................................................... 163 Driving with the “ABS” compartment (driver-side) ................... 145
Checking the engine oil level .............. 161 braking system ........................................... 114 Fuses and relays in the passenger
Checking the coolant fluid level ........ 161 Duplicating the keys .................................. 14 compartment (passenger’s side) ......... 147
Checking the F1 gearbox oil level .... 161

196
 Index

Replacing a wheel ..................................... 151

1
G M
Replacing other light bulbs .................. 136
Gear display (F1) ........................................ 91 Main engine specifications ...................... 24 Replacing the auxiliary stop
Gearshifting (F1 gearbox) .................... 104
Glove compartment .................................. 125
Maintenance of the seat belts and
pretensioners .............................................. 166
light and side marker bulbs ................. 136
Replacing the brake pads
2
Maintenance schedule ............................ 160 and brake discs .......................................... 157
H Maintenance ................................................ 160 Replacing the front direction
Handbrake lever ........................................ 117
Hazard warning lights ............................... 77
O
indicator and position light bulbs .... 133
Replacing the low beam/high beam
light bulbs .................................................... 133
3
Headlight washer ........................................ 98 Occupant Classification System ............ 50
Horn control ................................................. 97 Operation with the engine off (F1) .. 101 Replacing the license plate
How to use the tires ................................ 164 Overview of controls ................................. 64 light bulb ...................................................... 136

I P
Replacing the position light bulbs .... 133
Replacing the taillight bulbs ................ 135
Roof panel controls .................................... 94
4
ICE mode ....................................................... 95 Parking ........................................................... 109
Identification plates and labels ............. 18 Passenger-side power window .............. 72 S
If the vehicle is stored
for long periods ......................................... 167
Performance .................................................. 24
Pocket-change compartments .............. 126 Safe driving ................................................. 112
Seat belts ........................................................ 34
5
Ignition switch ........................................... 116 Power windows ............................................ 72
Instrument panel ......................................... 78 Pretensioners ................................................ 36 Seats ............................................................... 118
Service ................................................................ 4
Internal rear-view mirror ....................... 120

L
Push start (F1) ........................................... 107
Push start (Mechanical Gearbox) ...... 108 Spare parts ........................................................ 6
SPORT mode ............................................... 95
6
R Start button ................................................... 95
Light switch ................................................... 73 Starting and warming up the engine

7
Light bulbs ................................................... 138 RACE mode .................................................. 96 (F1 gearbox) ............................................... 102
Location of the fuse Rain sensor .................................................... 98 Stopping the vehicle (F1 gearbox) ... 105
and relay boxes ........................................... 140 Recharging the battery ........................... 154 Sun radiation sensor ................................ 125
LOW GRIP mode ....................................... 95 Recommended lubricants Sun visors ..................................................... 127
Luggage compartment lid ....................... 70 and fluids ....................................................... 30 System starting ........................................... 100
Replacing a fuse ........................................ 139
8
197
T V
Tachometer .................................................... 90 Vehicle keys ................................................... 12
TFT display ................................................... 79
TFT display buttons .................................. 80 W
TFT display warning lights ..................... 86
Tire pressure and temperature Warning lights .............................................. 91
monitoring system ...................................... 55 Warranty and Service Book .................. 160
Tire pressure calibration button ........... 94 Water temperature gauge ........................ 92
Toolkit ............................................................ 130 Wheel and tires ............................................ 26
Towing hook ............................................... 152 Wheels and tires ........................................ 164
Transmission ratios ..................................... 24 When traveling ........................................... 112
Turning off the engine and While driving
the system (F1 gearbox) ........................ 106 (Mechanical Gearbox) ............................ 108
Twilight sensor ............................................. 75 Windshield washer ..................................... 97
Windshield wipers ...................................... 97
U Windshield washer fluid ......................... 164

Updating ............................................................ 6
“UP” gearshift lever ................................... 97

198