GQCCO Company Profile - Rev 21 DT 09 Jan 2019

GULF QUALITY CONTROL COMPANY LTD.
COMPANY PROFILE
PO BOX: 3646, Al Khobar 31952, Kingdom of Saudi Arabia,Tel: 013 899 9728 Fax: 013 897 8078
Email: [email protected]
Registered Office: Dhahran/ Jubail Highway,Al Faihaa Area , Jordan St. Dammam, Al Khobar-
31952, Kingdom of Saudi Arabia
Providing Qualitative insPection solutions to the industry”
GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 1 of 34

Table of Contents
1) Introduction
2) Quality Policy
3) Policy statement
4) Safety Policy statement
5) Mission Statement
6) Office and Addresses
7) Organization Chart
8) Range of Services
9) Inspection and NDT Services
10) Equipment and Resources Available
11) Management Staffs & Company Manpower
12) Facilities available
13) Past Experience
14) Contracts Award and Appraisals

Introduction
GULF QUALITY CONTROL CO. Ltd (GQCCO), Saudi Arabia established in 2006,
for providing conventional NDT services as well the specialized NDT & Lifting
Equipment Inspection, in order to cater the rapidly growing markets in Gulf Region,
and to render the quality services in market, and in recent achievement, GQCCO is
well respected name within industry in the Gulf Region.
Although we undertake small contracts, our forte has recently been a large contract
such as pipelines, plant constructions, and specialized inspection contracts and so
on. We recognize that the quality of service that Client Organizations expect of their
staff can only be achieved by establishing a system that will allow this to happen to
GQCCO.
The system, as far as possible common to all projects, consists of general guidance
and a set of established procedures for all activities that are normally associated with
providing service to clients.
The emphasis within GQCCO is on planning the work from the earliest opportunity
so that all parties (Client and Staff) have a clear understanding of their contribution
towards the achievement of Quality Service. Project Plansare the means through
which each individual member of staff is aware of what is required of him.
In establishing such a system, GQCCO have been guided by the International

Standard ISO 9001-2000 “Quality Systems – Model for Quality Assurance in design,
development, production, installation and servicing.”

 NDT Services
Field of
 Third Party Inspection

Services  Training Services
 ANDT Inspection Services
 Inspection Personnel supply
 Crane, Lifting Gear Inspection
 Saudi Arabia
Areas  And all Gulf Region
 Oil & Petrochemical Industry
Industry  Power Generations
 Heavy steel Industries
 Railways

QUALITY POLICY
It is the policy of GULF QUALITY CONTROL CO. Ltd (GQCCO) to identify and
satisfy the needs of its customer by supplying quality product and services delivered
on time by professionally trained and committed employees supported by the sound
processes
We in GQCCO are committed to the concept of Quality Assurance as defined in ISO

9001: 2015
The management of GULF QUALITY CONTROL CO., LTD. is fully committed to,
Providing the best quality and cost effective services while adhering to global, legal
and customer standards in meeting all its customer's inspection & Testing services
demands at all times.
 GQCCO does this with utmost customer satisfaction and timely delivery
while continually improving its performance
 Implementing the Quality Management System and enhance the customer

satisfaction.
 Promoting the culture of continual quality improvements and the philosophy

of getting things “Right first time”
 Enhancing the skills of the staff through continual Training, review and
actively pursue an on-going Quality Policy to perform their work more
effectively.
_____________________
General Manager
Gulf Quality Control Co., Ltd.

SAFETY POLICY STATEMENT
Our policy is to provide and maintain safe and health working condition, equipment
and system of work for all of our employees and to provide such information, training
and supervision, as they need for this purpose. We also accept our responsibility for
the health and safety of other people who may be affecting by our activities.
Allocation of duties for safety matter and the particular arrangements, which will be
make to implement the policy, are set out in the Loss Prevention Program. The
policy will be keep up to date, particularly as the business changes in nature and
size. To ensure this, the policy and the way in which it has been operated will be
reviewed every year in Internal Auditing.
MISSION STATEMENT
GQCCO is committed to provide highest quality of services in specialized Inspection,

NDT services and Lifting Equipment Inspection through worldwide. We aim to offer
a comprehensive end-to-end in house package of design, engineering, resourcing
and executing to today’s owner, operator or engineering contractor.
We strive to provide the most reliable, cost effective solution within the rigorous
timescales demanded by our clients, whilst maintaining the highest standards of
integrity and quality.

Office and Addresses
Contact Person:
Gulf Eng. Ahmed Afifi - General Manager
SATYA. MULLAPUDI – Operations General
Quality Manager
Xavier Louis – ANDT Supervisor
Control Mohamed Teleb – Lifting Inspection Team

Leader
Postal Address:
Co Ltd., P.O. Box: 3646, Al Khobar 31952
Tel: +966 3 899 9728
Saudi Arabian Office Fax: +966 3 897 8078
Email: [email protected]
Office Location:
Dhahran/ Jubail Highway,
Al Faihaa Area , Jordan St. Dammam
Al Khobar- 31952
Kingdom of Saudi Arabia
Website: www.gqcco.com

Organization Chart
Faisal Al Harbi Dr. Abdel Hamid

Hassanein
President
Consultant
Ahmed Afifi
General Manager
Ahmed El Shiekh Hussain Al Eissa HR Manager

Finance Manager
Yasser Al Ghallab SATYA.MULLAPUDI SATYA.MULLAPUDI

Executive Secretary
Operations General Manager Management Rep
Mohamed Teleb Xavier

Operations Louis
Manager QMS Representative
ANDT Supervisor
Lifting Inspection Team
Leader nager
Qamar Nawaz Ahmed Afifi P. Karthikeyan Mohsen Hassanein

Technical Manager
Radiological
Protection Contract Representative Operations Supervisor Certified NDT Level III
Officer
Asst Radiological Site NDT Lifting NDT Instructor

Protection Officer Representative Technicians Equipment
inspector

Range of Services
Training and Certification on ASNT
GQCCO is the one of best training center in the Gulf for conducting training
and examination in nondestructive testing as per ASNT requirements. Training
and certification provided on following methods and GQCCO will organize
courses and examination in Saudi Arabia.
 Radiographic Testing Level I, II & III
 Ultrasonic Testing Level I, II & III
 Magnetic Particle Testing Level I, II & III
 Penetrant Testing Level I, II & III
 Visual Testing Level I, II & III
 Eddy current Testing Level I, II & III
 Infrared Thermography Level I, II & III
Training and Examinations on AWS-CWI

 AWS- CWI – Training and Examination
 AWS-SCWI – Training and Examination
NDT Inspection Services:
Conventional NDT
 Radiographic Testing,
 Ultrasonic Flaw Detection
 Liquid Penetrant Testing
 Magnetic Particle Testing
 Visual Inspection
 Radiographic Film Interpretation
 Ultrasonic Thickness Gauging

Specialized ANDT Services
 PHASED ARRAY UT INSPECTION
 TOFD UT INSPECTION
 IRIS Tube Inspection
 ET & RFET Tube Inspection
 MFL – Tank Floor Inspection
 Eddy Current Inspection
Lifting Equipment & Third Party Inspection:
THE MAIN NDT INSPECTION TECHNIQUES USED FOR LIFTING

GEAR INSPECTIONS ARE:
 Lifting Operation Supervision
 Lifting / Crane Equipment & Lifting Gear Examination
 Wire Rope Inspections
 Proof Load Testing for Lifting Equipment and Handling Tools
(Work Shop)
 Welding Inspection and Quality Control
 Offshore Containers / Cargo Baskets (CCUs)
 Rental Calibrated Test Weights.
 On Site Lifting Equipment Testing
LIFTING GEAR INSPECTION
Lifting gear inspection is a detailed visual and operational inspection whereby individual lifting
gear items are examined to ensure their integrity and ongoing safe operation for lifting
operations. Lifting gear Inspections are performed on a regular basis depend in g on the
st andar d s and specif ication s of the equipment and its usage.

GQCCO HAS THE CAPABILITY TO INSPECT ALL FIXED AND LOOSE LIFTING GEAR
TYPES INCLUDING:
• Padeyes, Runway beams, Swing jibs

• Air winches, tuggers and other similar units
• Baskets, containers, skips, gas racks and lifting frames
• All loose lifting tackle (slings, shackles, webbing and so forth)
• All lifting machines (chain blocks, lever hoists, pulling machines etc)
• Lifeboat and life raft davit/deployment systems
• Cranes
• Forklifts
• Tubular handling equipment and related items
• Anchor winches and associated plus towing assemblies
• Cantilever hold downs and beams
In addition to lifting gear inspections GQCCO can perform load test inspections
compliantwith international standards and codes.
GQCCO Inspection Service is a certified lifting gear inspection company with many years of
experience in the field.
Strictly working to local and international regulations and inspection standards, GQCCO provides
the highest quality inspection and verification service for safe and uninterrupted lifting
operations.www.gqcco.com

List of Reference Standards
Our Inspection is based on International Standards and Saudi Aramco applicable GL’s.
ASME A17-1 Safety Code for Elevators and Escalators

ASME A17-2 Inspectors Manual for Elevators and Escalators
ASME A17-3 Safety Code for Existing Elevators and Escalators
ASME B30-1 Jacks
ASME B30-2 Overhead and Gantry Cranes (Top running bridge, single or multiple
girder, top running trolley hoists)
ASME B30-3 Construction Tower Cranes
ASME B30-4 Portal, Tower and Pedestal Cranes
ASME B30-5 Mobile and Locomotive Cranes
ASME B30-6 Cranes – Derricks
ASME B30-7 Base mounted drum hoists
ASME B30-8 Floating Cranes and Floating Derricks
ASME B30-9 Alloy-steel Chain Slings, Wire Rope Slings, Metal Mesh Slings, Synthetic
Webbing Slings, Synthetic Round Slings
ASME B30.10 Eye Hooks, Clevis Hooks, Grab Hooks, Foundry Hooks, Sorting Hooks,
Choker Hooks, Shank Hooks
Monorail and Under hung Cranes
ASME B30.11
Storage / Retrieval Machines
ASME B30.13
ASME B30-14 Side Boom Tractors
ASME B30-16 Overhead Hoists (Under hung)
ASME B30-17 Overhead and Gantry Cranes (Top Running bridge)
ASME B30-18 Stacker Cranes (Top or Under running Bridge, Multi-Girder)
ASME B30.20 Below the Hook Lifting Devices
ASME B30-21 Manual Lever-operated Hoists
ASME B30.22 Articulating Boom Cranes
ASME B30.23 Personnel Lifting System
ASME B30.26 Rigging Equipment.
API Specs 2C Offshore Crane
ASME A 120.1 Safety requirements for powered Platforms for Bldg Maint
ASME A 92.2 Vehicle-mounted Elevating and rotating Aerial devices
ASME A 92.3 Manually Propelled Elevating work Platforms
ASME A 92.6 Self Propelled Elevating work Platforms
ASME A 92.5 Boom Supported Elevating work Platforms
S. Aramco GI 7.024 Marine and Offshore Crane Hoist and Rigging Operation
S. Aramco GI 7.026 Cranes and Heavy Equipment Accident reporting Procedure
S. Aramco GI 7.028 Cranes Lifts: Type and Procedure
S. Aramco GI 7.029 Inspection, Use and Maintenance of Below the Hook Lifting Equipment
Inspection and Testing of Elevating / Lifting Equipment
S. Aramco GI 7.030 Free Standing Base Mounted Jib Crane
BS 7333 Counter Balance Lift Trucks
BS 3726

Specialized Courses:
GQCCO is the one of best training center in the Gulf for conducting training
and examination in API Certifications. Training and certification examinations
provided on following area and GQCCO will organize courses and examination
in Saudi Arabia.
 Welding Inspection Technology – AWS/CWI and CSWIP

Refresher courses
 API 510 Pressure vessels Inspection
 API 570 Piping Inspection: Inspection, Repair, Alteration and
Rerating
 API 653 Tank Inspection Code
 ASME Boiler & pressure vessels Code
 Risk Based Inspection Implementation Integration & Management
 API 580 Risk Based Inspection Code
 API 579 Fitness for services of Piping, Pressure Vessels & Tanks,
Consultancy:
 NDT Level III Services
 NDT Specialist Consultancy
 ISO 9001:2000 Consultancy
 Third Party Inspection Services,
 Welder Qualification & Certification
Other Services
 Post Weld Heat treatment
 Portable Hardness Testing
 Positive Material Identification ( XRF and Spectro)
Man Power Supply of Inspection Personnel
GQCCO also providing Man power supply in the Field of NDT

&Inspection
 Inspection (RT, UT, MT, PT, and as Multi)

 Welding Inspectors (AWS/CWI, CSWIP 3.1, and CSWIP 3. 2)
 Coating Inspectors
 Civil Inspectors
 Lifting Equipment Inspectors
 API Inspectors
 ASNT NDT Level III, etc.,

Inspection and Non Destructive Testing
Services
1. Personnel
a. All personnel offered by GQCCO are selected on the ground of
maturity, experience and certification or approval in their chosen field,
being based on a technical background, thus ensuring a competent
inspector for any particular requirement.
b. Individual attainments include degree, national certificates, City and
Guilds, CSWIP, BARC, ASNT & AWS to suit client’s requirements.
2. Location
a. Personnel and/or services are available for work at any location, at any
location, at works, sties, on offshore, throughout the world covering the
oil, gas, nuclear electricity and petrochemical industries for new
construction, survey, maintenance or monitoring applications.
3. Equipment
a. Where equipment is required, GQCCO, under its progressive policies,
provide the best available instruments of modern manufacturer to
ensure the quality and reliability of such work undertaken.
4. Disciplines
a. Quality Assurance
i. Management, development of procedures, manuals,
interpretation of international codes and standards,
representation of client to third parties e.g. Customers, vendors,
documentation, etc.
b. Quality control
i. Implementation of codes and standards, control of quality from
vendors, contractors, sub-contractors, etc. monitoring of clients
issued material, surveillance of client’s products, services, labor
and documentations.
c. Inspection
i. Skilled personnel, full range of optical, mechanical, electrical
and electronic aids, to investigate and monitor conformity to
standards, specifications, drawings and the like, weld
examination, procedure, monitoring, dimensional checking etc.
5. Non Destructive Testing
a. GQCCO offers a comprehensive range of NDT services including
conventional NDT together with a range of highly sophisticated services
including pipelines radiography, automated ultrasonic systems, etc.
i. Radiography
1. Using portable equipment with mobile darkroom as
required for both x-ray and gamma ray techniques
including constant potential x-ray radiography- isotopes
such as Ir 192 and Co 60, etc.
ii. Ultrasonic Testing
1. Manual and automated systems using a range of
techniques including Time of Flight Diffraction (ToFD),
Phased Array Ultrasonic, Guided Wave Ultrasonic and
Corrosion Mapping.
2. Corrosion and thickness measurement surveys using a
variety of techniques and method Digital Radiography,
C-scan corrosion mapping, Phased Array Ultrasonic and
conventional Ultrasonic measurement techniques.
iii. Magnetic Particle Testing
1. Flaw detection, using current flow magnetic flux
induction and permanent magnetic techniques, with
wide variety of visual aids including fluorescent and day
light viewing inks and powders at ambient and elevated
temperature
iv. Penetrant Testing
1. Defect location by daylight or fluorescent dye process,
by aerosol, spray or bulk application of water or solvent-
based liquids.
v. Eddy Current Inspection
1. Crack detection, discontinuity location, coating and
material sorting using portable instruments.
vi. Hardness Testing
1. Employing portable manual, hydraulic or electronic
instruments

5.1 ANDT Services:
Tube Inspection – ECT, RFT, MFL & IRIS
Tube Inspection with Eddy Current Testing (ECT)
 Condensers
 Feed water heaters
 Heat exchangers
 Air conditioners
Eddy current testing is a noncontact method used to inspect

non ferromagnetic tubing. This technique is suitable for
detecting and sizing metal discontinuities such as corrosion,
erosion, wear, pitting, baffle cuts, wall loss, and cracks in
nonferrous materials.
Tube Inspection with an Internal Rotating Inspection System (IRIS) for Ferrous and Nonferrous
Materials
 Boilers
 Air coolers
 Heat exchangers
The ultrasonic IRIS option is used to inspect a wide range of

materials, including ferrous, nonferrous, and nonmetallic
tubing. This technique detects and sizes wall loss resulting
from corrosion, erosion, wear, pitting, cracking, and baffle
cuts. Olympus digital IRIS inspection technology is used
extensively as a prove-up technique for remote field testing,
magnetic flux leakage, and eddy current
inspections.
Tube Inspection with Remote Field Testing

(RFT)
 Boilers
 Carbon steel heat exchangers
Remote field testing (RFT) is being used to successfully inspect ferromagnetic tubing such as carbon steel or ferritic
stainless steel. This technology offers good sensitivity when detecting and measuring volumetric defects resulting from
erosion, corrosion, wear, and baffle cuts.
Tube Inspection with Magnetic Flux Leakage (MFL)

 Air coolers
 Carbon steel heat exchangers
Magnetic flux leakage (MFL) is a fast inspection technique, suitable for measuring wall loss and detecting sharp defects
such as pitting, grooving, and circumferential cracks. MFL is effective for aluminum-finned carbon steel tubes, because the
magnetic field is almost completely unaffected by the presence of such fins.
PAUT and TOFD Inspection
Phased Array Ultrasonic Testing (PAUT)

Our fully code-compliant PAUT offering provides an alternative to on-site radiography. Developments in construction codes
allow PAUT to be used as a direct replacement for radiography on piping butt welds to ensure assets meet the quality
control requirements of ASME B31.3 and B31.1 and numerous European standards. PAUT can be applied when
considering both workmanship and engineering critical assessment (ECA) acceptance criteria, with data being suitable for
accurate sizing and defect characterization.
Data Analysis
Sophisticated analysis software enables experienced operators to interrogate welds from multiple orientations including a
comprehensive evaluation of the weld root, fusion face, and weld toes.
Features:
 Identifies cracks, lack of fusion or penetration, porosity, and slag inclusions
 Radiation-free ultrasonic technique
 Rapid inspections with digital recording of data
Advantages:
 Welds from 0.84 inch in diameter up to flat plate may be inspected
 Wall thicknesses from 4 mm (Wall thickness below 4 mm may be possible using a go/no go strategy)
 Independent from site utilities due to battery operation and irrigation system
 Rapid inspections with digital recording of data
 Digitally-encoded scanning for accurate sizing
 Highly sensitive to fusion face flaws
 Free viewing software available to allow the client to review inspection data
 ASME and European code compliant
Considerations:
 Surface preparation is required to support the collection of quality data »
 100 mm of radial and axial clearance is required for scanner fitment (small bore scanner available for restricted
access scanning)
Time of Flight Diffraction (TOFD)

Time of Flight Diffraction (TOFD) is an advanced ultrasonic inspection method that is used primarily for weld inspection. It
is a key method in crack detection and sizing for in-service vessel and piping welds.
TOFD capitalizes on tip diffracted signals generated when a discontinuity within a weld receives ultrasonic mechanical
energy. Tip diffracted signals are omni-directional wave fronts emitted from the very tips of discontinuities. This results in
detection that is less sensitive to defect orientation and more accurate for through wall sizing when compared with
amplitude reliant ultrasonic methods.
Given crack geometry can be erratic, TOFD is an excellent tool for detection and sizing.
Features:
 Suitable for circumferential and axial weld inspection
 Weld joint fitting is less critical with TOFD when compared to other ultrasonic methods
 Capable of inspecting complex geometry
Advantages
 Through wall measurements based on arrival times, therefore more accurate than amplitude techniques.
 100% coverage, permanent record, instant analysis, reproducible fingerprinting for condition monitoring.
 Reduced sensitivity to defect orientation, particularly applicable to cracks
 Capable of inspecting complex geometry including weld joints, such as bend to flange joints.
 High Temperature equipment can be used for temperatures up to 200°C
 Sensitivity / Theoretical Minimum Detectable flaw is ~0.5mm
 General Accuracy +/- 0.5mm
 Monitoring Accuracy +/- 0.3mm
Considerations:
 Near-surface, dead zone, however, computer processing can overcome this restriction
 Generally, minimum nominal wall thickness ~6mm
 Material to be inspected must be penetrable by ultrasonic sound waves, specifically any coating must allow
ultrasonic coupling.
 Due to poor signal-to-noise ratios encountered during inspection of stainless steels, fine cracking, such as SCC
can be difficult to detect. This is strongly dependent on grade of material, and trials/validations can be carried
out to confirm suitability.
 The outer surface should be clean and free from loose impediments such as insulation or other debris. Debris
could cause the ultrasonic signal to scatter, therefore not reaching the inner surface. In this scenario, the signal
to noise ration may not be sufficient to allow credible data to be recorded. This is a prerequisite for all methods
of ultrasonic inspection.
 Complementary inspection techniques including phased array or manual ultrasonic testing can be carried out
for accurate flaw characterization.
Additional Features:
 100% encoded coverage of Weld & HAZ
 Digital storage of inspection data » Fully auditable inspections
 Supplementary TOFD for 100% fusion face coverage, where phased array is carried out from one side only on
pipe to fitting welds
 Various materials can be inspected, including stainless steels
6. General
a. The above scope of services offered serves as illustration only,
however, other services, methods or equipment can be provided
as required, these include inspection systems, pressure testing,
x-ray crawler units, metallurgical constancy, real time imaging,
fiber optics, acoustic emission, MFL Tank floor Inspection, Tube
Inspection, Positive Material Identification etc.,

Management Staffs
1) Mr.Faisal Al-Harbi President

2) Eng. Ahmed Afifi General Manager& Finance
3) Mr. Satya. Mullapudi Operations General Manager
4) Mr. Xavier Louis ANDT Supervisor- Level III PAUT & TOFD
5) Mr. Mohamed Teleb Lifting Inspection Team Leader
6) Mr. Hussein Al-Eissa HR officer
7) Mr. Ahmed Abdulla Administration
8) Mr. Qamar Nawaz Radiation Safety Officer
9) Mr. Ahmed Al Sheikh Accounts
10) Mr. Karthikeyan. P Operations Supervisor
Training Course Instructors:
1) Mr. Ramakrishnan - ASNT NDT Level III Course

Instructor
2) Mr. Diwakar Joshi - ASNT NDT Level III, ASME & API
Instructor
3) Mr. Mohammed Zaky - ASNT NDT Level II, III & API
Instructor
Key Personnel:
1) Mr. Satya. Mullapudi Operations General Manager
2) Mr. Xavier Louis ANDT Supervisor- Level III PAUT & TOFD
3) Mr. Karthikeyan P NDT Supervisor & Asst Rad.
Safety in charge
4) Mr. Qamar Nawaz Main Rso .
5) Mr. Mohamed Teleb Lifting Inspection Team Leader
6) Mr. Ahmed Abdelsamie RSO & AREA RAD.
7) Mr. Musab Edris Back-up RSO and KACARE Rep.

List of Technical Manpower
Radiation Safety Officers (RSO)
1 Radiation Protection Officer TOTAL - 6
ASNT NDT LEVEL-III’s

2 ASNT NDT Level-III TOTAL - 3
ASNT NDT LEVEL-II’s

3 ANST NDT LEVEL-II
TOTAL -100
(RT, UT, MT, PT,)
RTFI TECHNICIANS
4 Radiographic Film Interpretation Tech.
TOTAL - 06
RTFI
PMI TECHNICIANS
5 Positive Material Identification Tech. TOTAL - 04
ARAMCO APPROVED UT TECHNICIANS

6 UT shear wave technicians TOTAL - 04
PAUT /TOFD TECHNICIANS

7 PAUT/TOFD Technicians TOTAL - 02
TUBE INSPECTION TECHNICIANS

8 Tube Inspection Technicians. TOTAL - 04
LEI INSPECTORS
9 Lifting Equipment Inspectors TOTAL - 08

Facilities Available with GQCCO
No’s
SR # Facilities Available
1 PAUT/TOFD EQUIPMENT SET 1
2 Heat Exchanger Tube inspection equipment,RFET,ECT,MFL,IRIS 1
3 PMI- X-Ray Fluorescence (XRF) and Spectro 1+1
4 SAFE RAD Selenium 75 source complete set 2
Radiographic Projector - 660 B & Sigma 880 with Accessories & Safety
18
5 Equipments
6 Magnetic Particle Testing Yoke - AC 8
7 Penetrant Testing Kits 16
8 Ultrasonic Flaw Detectors –Krautkramer & Sonatest with Accessories 7
9 Ultrasonic D-Meters for Thickness Measurement 8
10 Radiographic Film Viewer 10
11 Brinell Hardness Kit 6
12 Computer, TV, VCR, LCD Projector, DVD Player Various
13 CD of Training Materials for RT, UT, MT, PT, ET & RTFI 4 Sets
14 Video Tape & CD Training Materials in Welding Technology 3 Sets
15 Well Furnished class room 1
16 Reference Radiographs & Production Radiographs for RTFI 1
17 Black Light Assembly 4
18 Defective Samples of RT, UT, MT, PT, VT 4 Each
19 Copying Machine 2
20 Library of Major Codes & Standards, Welding Related Reference books Various
21 Post Weld Heat Treatment Equipments 1
22 Training kit and test plate samples various

Past Experience
GQCCO is working in the inspection field since 1984 and our experience enabled us
to perform third party inspection services for your company besides the other
petroleum companies.
GQCCO is Registered & Approved 3rd Party Inspection Service Provider for;
Saudi Aramco Vendor № 10035166
SABIC – Saudi Basic Industries Corporation Vendor № 505188
PETRO RABIGH - Vendor № 100666
SWCC – Saline Water Conversion Corporation Registered
SADARA Registered
SATORP - Vendor № 10779
SEC-Saudi Electricity Company Vendor № 60465
Royal Commission RCJ 000496
Maaden Vendor № 13159

List of Major Clients in Saudi Arabia and contracts details:
 From 2006 to Till Date

1-1 PETROJET
Country : SAUDI ARABIA
Location within country : YANBU, Manifa,Jubail
Project name : Saudi Aramco Various Projects
1-2 CCC – Consolidated Contractor Co
Location within country : RABIGH, Khurshaniyah
Project name : PETRORABIGH PROJECT, KGP Project
1-3 Inma Steels
Location within country : JUBAIL
Project name : Various Projects
1-4 MISA
Location within country : JUBAIL
Project name : Training Services in NDT; Radiographic Testing Services
1-5 PETRORABIGH REFINERIES.
Location within country : RABIGH.
Project name : Non-Destructive Test Contract ( Since 2008 untill 2022)
1-6 Al Saghyir Boilers & Pressure Vessels Co.
Location within country : 2nd Industrial City - Riyadh
Project name : Radiographic Testing Services – SWCC Project

1-7Saudi Services for Electro Mechanic Works Co. Ltd
Location within country : SHOIBA
Project name : SWCC – Shoaiba Phase-3 WTS Project
1-8Saudi Aramco
Location within country : Dhahran
Project name : NDT Level III & API Training Services Direct Contract
1-9 SAUDI ARABIAN SAIPEM Ltd
Location within country : Khurais Project – Saudi Aramco – Dammam Fab shop
Project name : Radiographic Testing Services
1-10 MMG – AL MOJIL Group
Location within country : Riyadh Refinery – 50” Flare Line Replacement Project
Project name : Radiographic Testing & MT PT Services
1-11 AL BADER ESTABLISHMENT
Location within country : ABQAIQ
Project name : Radiographic Testing & MT PT Services – Al Nauyyim
1-12 SAUDI ARCHIRODON
Location within country : Hafr Al Batin
Project name : Training Services in NDT
1-13 STFA Marine Construction Co
Location within country : Manifa – Saudi Arabia
Project name : Ultrasonic Testing Contract – Manifa Causeway Project

1-14 Metal Services Contracting and Trading Co
Location within country : Rabigh and Abqaiq - Saudi Arabia
Project name : NDT Service Contract
1-15 Faysal M. Qahtani & Sons Co
Location within country : Khurais – Saudi Arabia
Project name : Radiographic Testing Contract
1-16 Salim Abdullah Al Sheban Est.
Location within country : PETRORABIGH Expansion – Saudi Arabia
Project name : Radiographic Testing Contract
1-17 Contracting and Trading Co (CAT)
Location within country : Abqaia – Saudi Arabia
Project name : Radiographic and Ultrasonic Testing Contract
1-18 China Railway Company
Location within country : Hail
Project name : Rail track UT inspections
1-19SINOPECEngineering Group
Location within country : Jizan
Project name : Radiographic and PT/MT Testing Contract
1-20Gulf Riyadh
Location within country : Dammam
Project name : Radiographic and HT Testing Contract

1-21 Aasia Steel Factory Co. Ltd
Location within country : Jubail
1-22 Arabian Pipe Company
Project name : NDT manpower Contract
1-23 Mohamad Al- Barghash Trading and Cont. Co.
Location within country : Abqaiq, Nayyim, Al Hota, Jubail etc..
1-24 OMS Oil Field Services Ltd.
Location within country : Abqaia
Project name : Radiographic and MT, WQT Testing Contract
1-25Saudi Electricity Company (SEC)
Location within country : Various regions
Project name : NDT Services Contracts
1-26 SABIC – GLOBAL CONTRACT
Location within country : All Afiliates in saudi Arabia
Project name : Conventional NDT Services
1-27 ARCELOR MITTAL PIPE COMPANY
Project name : Manual UT services
1-28 NATIONAL CONTRACTING COMPANY.
Location within country : Khurais

Project name : Radiographic and MT, WQT Testing Contract
1-29 M/S BIN QURAYA
Location within country : Abqaia To Haradh
Project name : Radiographic and,UT, MT,PT,PMI and PWHT

services
1-30 M/S SAFAMI(Saudi Arabian Metal Fabrication co.)
Location within country : Khobar and Jubail
Project name : Radiographic and MT, UT,PMIWQT Testing
1-31 SAUDI ARABIAN KENTZ.
Location within country : Hauta
Project name : Radiographic and MT, UT,WQT Testing
1-32 ARKAD SAUDI ARABIA Ltd.
Location within country : Fadilli
Project name : Radiographic and MT, PT,UT,PMI WQT Testing
1-33 GLOBAL IWI ARABIA LTD.
Location within country : Wasit Gas plant
Project name : Radiographic and MT, PT,UT,PMI WQT Testing

Contracts Award and Appraisal
(Namely few)


GQCCO Company Profile - Rev 21 DT 09 Jan 2019

Uploaded by

Copyright:

Available Formats

GQCCO Company Profile - Rev 21 DT 09 Jan 2019

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GQCCO Company Profile - Rev 21 DT 09 Jan 2019

Uploaded by

Copyright:

Available Formats

GULF QUALITY CONTROL COMPANY LTD.

Providing Qualitative insPection solutions to the industry”

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 1 of 34

4) Safety Policy statement

6) Office and Addresses

9) Inspection and NDT Services

10) Equipment and Resources Available

11) Management Staffs & Company Manpower

12) Facilities available

13) Past Experience

14) Contracts Award and Appraisals

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 2 of 34

In establishing such a system, GQCCO have been guided by the International

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 3 of 34

 ANDT Inspection Services

 Inspection Personnel supply

 Crane, Lifting Gear Inspection

Areas  And all Gulf Region

 Oil & Petrochemical Industry

Industry  Power Generations

 Heavy steel Industries

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 4 of 34

We in GQCCO are committed to the concept of Quality Assurance as defined in ISO

 Implementing the Quality Management System and enhance the customer

 Promoting the culture of continual quality improvements and the philosophy

Gulf Quality Control Co., Ltd.

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 5 of 34

GQCCO is committed to provide highest quality of services in specialized Inspection,

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 6 of 34

SATYA. MULLAPUDI – Operations General

Xavier Louis – ANDT Supervisor

Control Mohamed Teleb – Lifting Inspection Team

Co Ltd., P.O. Box: 3646, Al Khobar 31952

Tel: +966 3 899 9728

Saudi Arabian Office Fax: +966 3 897 8078

Dhahran/ Jubail Highway,

Al Faihaa Area , Jordan St. Dammam

Kingdom of Saudi Arabia

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 7 of 34

Faisal Al Harbi Dr. Abdel Hamid

Ahmed El Shiekh Hussain Al Eissa HR Manager

Yasser Al Ghallab SATYA.MULLAPUDI SATYA.MULLAPUDI

Mohamed Teleb Xavier

Qamar Nawaz Ahmed Afifi P. Karthikeyan Mohsen Hassanein

Asst Radiological Site NDT Lifting NDT Instructor

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 8 of 34

Training and Examinations on AWS-CWI

 Ultrasonic Thickness Gauging

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 9 of 34

THE MAIN NDT INSPECTION TECHNIQUES USED FOR LIFTING

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 10 of 34

• Padeyes, Runway beams, Swing jibs

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 11 of 34

ASME A17-1 Safety Code for Elevators and Escalators

GQCCO Company Profile – Rev. 21 Dt. 09th Jan 2019 Page 12 of 34

 Welding Inspection Technology – AWS/CWI and CSWIP

GQCCO also providing Man power supply in the Field of NDT

 Inspection (RT, UT, MT, PT, and as Multi)