BS en 14399-7-2007 (2010)

BRITISH STANDARD BS EN
14399-7:2007
Incorporating
Corrigendum
October 2010
High-strength
structural bolting
assemblies for
preloading —
Part 7: System HR — Countersunk
head bolt and nut assemblies
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
ICS 21.060.01
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Istanbul Teknik Universtesi/5956919001
No reproduction or networking permitted without license from IHS Not for Resale, 12/10/2010 01:27:26 MST
BS EN 14399-7:2007
National foreword
This British Standard is the UK implementation of EN 14399-7:2007.

Together with BS EN 14399-1:2005, BS EN 14399-2:2005, BS EN
14399-3:2005, BS EN 14399-4:2005, BS EN 14399-5:2005, BS EN
14399-6:2005, BS EN 14399-8:2005 and BS EN 14399-10:2009, it supersedes
BS 4395-1:1969 and BS 4395-2:1969 which were declared obsolescent in
2007. (BS 4395-1:1969 and BS 4395-2:1969, together with BS 4604-1:1970
and BS 4604-2:1970, currently support the BS 449 and BS 5950 series of
standards.)
The BS EN 14399 series of standards comprise ten parts. BS EN
14399-1:2005 provides the general and harmonization requirements to which
the other parts, which provide specific requirements regarding manufacture,
materials and testing, relate.
It was agreed to extend the period of co-existence for BS EN 14399 Parts 1 to
6 to two years, CEN/TC 185/WG 6 applied for and received approval for the
same extension period to be applied to all other structural bolting standards.
Bolt and nut assemblies with countersunk heads conforming to BS EN
14399-7:2007 have been designed to withstand the same axial tensile load as
bolt and nut assemblies with hexagon heads conforming to BS EN
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
14399-3:2005 and BS EN 14399-4:2005.

The UK participation in its preparation was entrusted by Technical Committee
FME/9, Nuts, bolts and accessories/steering committee, to Subcommittee
FME/9/1, Material.
A list of organizations represented on this committee can be obtained on
request to its secretary.
This publication does not purport to include all the necessary provisions of a
contract. Users are responsible for its correct application.
Compliance with a British Standard cannot confer immunity from
legal obligations.
This British Standard was Amendments/corrigenda issued since publication

published under the authority
of the Standards Policy and
Strategy Committee Date Comments
on 31 January 2008
31 October 2010 Correction to national foreword
© BSI 2010
ISBN 978 0 580 69003 7

EUROPEAN STANDARD EN 14399-7
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2007
ICS 21.060.01
English Version
High-strength structural bolting assemblies for preloading - Part

7: System HR - Countersunk head bolt and nut assemblies
Boulonnerie de construction métallique à haute résistance Hochfeste planmäßig vorspannbare

apte à la précontrainte - Partie 7: Système HR - Boulons à Schraubenverbindungen für den Metallbau - Teil 7: System
tête fraisée (vis et écrou) HR - Garnituren aus Senkschrauben und Muttern
This European Standard was approved by CEN on 10 November 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels

--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14399-7:2007: E
worldwide for CEN national Members.

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Contents
Foreword......................................................................................................................................................................3
Introduction .................................................................................................................................................................4
1 Scope ..............................................................................................................................................................5
2 Normative references ....................................................................................................................................5
3 Terms and definitions ...................................................................................................................................6
4 Bolts ................................................................................................................................................................6
5 Nuts ...............................................................................................................................................................12
6 Designation of the countersunk head bolt/nut assembly .......................................................................16
7 Associated washers ....................................................................................................................................16
8 Functional characteristics of the bolt/nut/washer(s) assembly..............................................................17
Bibliography ..............................................................................................................................................................21
Figures
a
Figure 1 — Dimensions of bolts Table 2 — Dimensions of bolts ...............................................................................7
Figure 2 — Example for marking of a bolt ..................................................................................................................12
Figure 3 — Dimensions of nuts ..................................................................................................................................12
Figure 4 — Example for marking of a nut ...................................................................................................................16
Figure 5 — Adapter.....................................................................................................................................................17
Figure 6 — Test set-up ...............................................................................................................................................18
Tables
Table 1 — Systems of bolt/nut/washer(s) assemblies..................................................................................................4
Table 2 — Dimensions of boltsa ...................................................................................................................................8
Table 3 — Specifications for bolts and reference standards ......................................................................................11
Table 4 — Dimensions of nuts a .................................................................................................................................13
Table 5 — Specifications for nuts and reference standards.......................................................................................14
Table 6 — Proof load values of nuts...........................................................................................................................15
Table 7 — Hardness values of nuts, if specified ........................................................................................................15
Table 8 — Characteristics of adapters .......................................................................................................................17
Table 9 — Values for ∆Θ1 ..........................................................................................................................................19
Table 10 — Values for ∆Θ2 ........................................................................................................................................19
2 --`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Foreword
This document (EN 14399-7:2007) has been prepared by Technical Committee CEN/TC 185 “Fasteners”, the se-
cretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by
June 2010.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-
tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den-
mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the
United Kingdom.
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Introduction
This document for structural bolting reflects the situation in Europe where two technical solutions exist to achieve the
necessary ductility of bolt/nut/washer assemblies. These solutions utilize different systems (HR and HV) of
bolt/nut/washer assemblies, see Table 1. Both systems are well proved and it is up to the experts responsible for
structural bolting whether they use the one or the other system.
It is however important for the performance of the assembly to avoid mixing up the components of both systems.
Therefore bolts and nuts for both systems are standardized in one single part of this European Standard each and the
marking of the components of the same system is uniform.
Table 1 — Systems of bolt/nut/washer(s) assemblies
Bolt/nut/washer(s) Bolt/nut/washer(s)
assembly assembly
System HR System HV
General
EN 14399-1
requirements
Bolt/nut
EN 14399-3, EN 14399-7 EN 14399-4, EN 14399-8
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
assemblies
Marking HR HV
Property classes 8.8/8 or 8.8/10 10.9/10 10.9/10
Washer(s) EN 14399-5 or EN 14399-6 EN 14399-5 or EN 14399-6
Marking H H
Suitability test for
EN 14399-2 EN 14399-2
preloading
Preloaded bolted assemblies are very sensitive to differences in manufacture and lubrication. Therefore it is important
that the assembly is supplied by one manufacturer who is always responsible for the function of the assembly.
For the same reason it is important that the coating of the assembly is under the control of the manufacturer.
Beside the mechanical properties of the components, the functionality of the assembly requires that the specified pre-
load can be achieved if the assembly is tightened with a suitable procedure. For this purpose a test method for the
suitability of the components for preloading was created which will demonstrate whether the function of the assembly
is fulfilled.
Attention is drawn to the importance of ensuring that the bolts are correctly used if satisfactory results are to be ob-
tained. For recommendations concerning proper application, reference to prEN 1090-2 is made.
4
BS EN 14399-7:2007
EN 14399-7:2007 (E)
1 Scope
This document belongs to the suite of European Standards EN 14399 and is designed to be read in conjunction
with EN 14399-1 for:
 general requirements;
 testing for conformity evaluation;
 evaluation of conformity;
 regulatory marking;
for assemblies of high-strength structural countersunk bolts and nuts of system HR suitable for preloaded joints
with thread sizes M12 to M36 and bolt property classes 8.8 and 10.9 and EN 14399-2 for suitability testing.
This document gives requirements for:
 dimensions;
 associated washer(s) according to EN 14399-5 or to EN 14399-6;
 performance and suitability tests;
for assemblies with thread sizes M12 to M36 and bolt property classes 8.8 and 10.9.
Countersunk bolt and nut assemblies to this document have been designed to allow preloading of at least 0,7 fub ×
As1) according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by elongation of the bolt. For this
purpose the components have the following characteristics:
 nut height according to style 1 (see EN ISO 4032),
 thread length of the bolt according to ISO 888.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 1993-1-8, Eurocode 3: Design of steel structures — Part 1-8: Design of joints
EN 10045-1, Metallic materials - Charpy impact test - Part 1: Test method
EN 14399-1:2005, High-strength structural bolting assemblies for preloading - Part 1: General requirements
EN 14399-2:2005, High-strength structural bolting assemblies for preloading - Part 2: Suitability test for preloading
EN 14399-5, High-strength structural bolting assemblies for preloading - Part 5: Plain washers
EN 14399-6, High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
1) fub is the nominal tensile strength (Rm) and As is the nominal stress area of the bolt.
5
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
EN 20898-2, Mechanical properties of fasteners - Part 2: Nuts with specified proof load values - Coarse thread (ISO
898-2:1992)
EN 26157-1, Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general requirements (ISO
6157-1:1988)
EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and
studs (ISO 898-1:1999)
EN ISO 3269, Fasteners - Acceptance inspection (ISO 3269:2000)
EN ISO 4032, Hexagon nuts, style 1 - Product grades A and B (ISO 4032:1999)
EN ISO 4759-1, Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C (ISO
4759-1:2000)
EN ISO 6157-2, Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995)
EN ISO 10684, Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: Test method
ISO 261, ISO general purpose metric screw threads — General plan
ISO 888, Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts
ISO 965-2, ISO general purpose metric screw threads - Tolerances - Part 2: Limits of sizes for general purpose ex-
ternal and internal screw threads - Medium quality
ISO 965-5, ISO general purpose metric screw threads - Tolerances - Part 5: Limits of sizes for internal screw
threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before
galvanizing
3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 14399-1:2005 and 14399-2:2005 apply.
4 Bolts
4.1 General
The test method for suitability for preloading shall be as specified in EN 14399-2.
4.2 Dimensions of bolts
See Figure 1 and Table 2.

--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
6
BS EN 14399-7:2007
EN 14399-7:2007 (E)
The difference between lg and ls shall not be less than 1,5 P.
a Incomplete thread u ≤ 2P
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
Figure 1 — Dimensions of bolts

BS EN 14399-7:2007
EN 14399-7:2007 (E)
a
Table 2 — Dimensions of bolts
Dimensions in millimetres
Thread d M12 (M14)b M16 (M18)b M20

Pc 1,75 2 2 2,5 2,5
d 30 34 38 42 46
b (ref.) e — 40 44 48 52
f — — — — 65
max. 12,70 14,70 16,70 18,70 20,84
ds
min. 11,30 13,30 15,30 17,30 19,16
max. 24,00 28,00 32,00 36 40
dk
min. 23,16 27,16 31,16 35 39
max. 16,5 19,5 22,5 25,5 28,5
i
min. 15,5 18,5 21,5 24,5 27,5
nom. 8,00 9,00 10,00 12,0 13,0
k max.i 8,75 9,75 10,75 12,9 13,9
min.j 7,25 8,25 9,25 11,1 12,1
max. 1,6 1,6 1,6 2 2
r
min. 1,2 1,2 1,2 1,5 1,5
max. 3,0 3,0 3,0 3,5 3,5
n
min. 2,5 2,5 2,5 3,0 3,0
t max. 4,5 4,5 4,5 5,0 5,0
min. 3,0 3,0 3,0 3,5 3,5
l ls and lg g, h
ls lg ls lg ls lg ls lg ls lg
nom. min. max. min. max. min. max. min. max. min. max. min. max.
45 43,75 46,25 14 19,25
50 48,75 51,25 14 19,25 18 24
55 53,5 56,5 16,25 25 18 24
60 58,5 61,5 21,25 30 16 22 18 24 23 30,5
65 63,5 66,5 26,25 35 21 31 18 24 23 30,5
70 68,5 71,5 31,25 40 26 36 22 32 23 30,5 --`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
75 73,5 76,5 36,25 45 31 41 27 37 21 28,5 23 30,5

80 78,5 81,5 41,25 50 36 46 32 42 25,5 38 23 30,5
85 83,25 86,75 46,25 55 41 51 37 47 30,5 43 26,5 39
90 88,25 91,75 51,25 60 46 56 42 52 35,5 48 31,5 44
95 93,25 96,75 56,25 65 51 61 47 57 40,5 53 36,5 49
100 98,25 101,75 61,25 70 56 66 52 62 45,5 58 41,5 54
110 108,25 111,75 66 76 62 72 55,5 68 51,5 64
120 118,25 121,75 76 86 72 82 65,5 78 61,5 74
130 128 132 80 90 76 86 69,5 82 65,5 78
140 138 142 90 100 86 96 79,5 92 75,5 88
150 148 152 100 110 96 106 89,5 102 85,5 98
160 156 164 110 120 99,5 112
8
BS EN 14399-7:2007
EN 14399-7:2007 (E)
Table 2 (continued)
Thread d M22 M24 M27 M30 M36
Pc 2,5 3 3 3,5 4
b (ref.) d 50 54 60 66 78
e 56 60 66 72 84
f 69 73 79 85 97
max. 22,84 24,84 27,84 30,84 37,00
ds
min. 21,16 23,16 26,16 29,16 35,00
max. 44 48 54 60,0 72,0
dk
min. 43 47 53 58,8 70,8
max. 30,5 33,5 37,5 42,5 50,5
i
min. 29,5 32,5 36,5 41,5 49,5
nom. 14,0 16,0 17,5 19,50 23,00
k max.i 14,9 16,9 18,4 20,55 24,05
min.j 13,1 15,1 16,6 18,45 21,95
max. 2 2 2,5 2,5 2,5
r
min. 1,5 1,5 2 2 2
max. 3,5 3,5 3,5 4,0 4,0
n
min. 3,0 3,0 3,0 3,5 3,5
t max. 5,0 5,0 5,0 5,5 5,5
min. 3,5 3,5 3,5 4,0 4,0
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
l ls and lg g, h
ls lg ls lg ls lg ls lg ls lg
nom. min. max. min. max. min. max. min. max. min. max. min. max.
65 63,5 66,5 25 32,5
70 68,5 71,5 25 32,5 28 37
75 73,5 76,5 25 32,5 28 37
80 78,5 81,5 25 32,5 28 37 31 40
85 83,25 86,75 25 32,5 28 37 31 40
90 88,25 91,75 27,5 40 28 37 31 40 34,5 45
95 93,25 96,75 32,5 45 28 37 31 40 34,5 45
100 98,25 101,75 37,5 50 31 46 31 40 34,5 45
110 108,25 111,75 47,5 60 41 56 31 40 34,5 45 41 53
120 118,25 121,75 57,5 70 51 66 45 60 34,5 45 41 53
130 128 132 61,5 74 55 70 49 64 40,5 58 41 53
140 138 142 71,5 84 65 80 59 74 50,5 68 41 53
150 148 152 81,5 94 75 90 69 84 60,5 78 46 66
160 156 164 85 100 79 94 70,5 88 56 76
170 166 174 95 110 89 104 80,5 98 66 86
180 176 184 105 120 99 114 90,5 108 76 96
190 186 194 115 130 109 124 100,5 118 86 106
200 196 204 125 140 119 134 110,5 128 96 116
NOTE The popular lengths are defined in terms of lengths ls min and lg max.

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Table 2 (continued)
a For hot-dip galvanized bolts, the dimensions apply before galvanizing.
b Non-preferred sizes
c P is the pitch of thread.
d For lengths l
nom. ≤ 125 mm.
e For lengths 125 mm < l
nom. ≤ 200 mm.
f For lengths lnom. > 200 mm.
g lg max. = lnom. – b
ls min. = lg max. – 5P
h When l g is less than k
s min. as calculated by the equation in nom. + 0,5d then its value shall be knom. + 0,5d and
lg max = ls min.+ 3P. Bolts with shortened thread length are shown above the line.
i kmax. includes the height of embossed marking, if any.
j kmin. excludes the height of embossed marking, if any.
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
10
BS EN 14399-7:2007
EN 14399-7:2007 (E)
4.3 Specification for bolts and reference standard
Table 3 — Specifications for bolts and reference standards
Material Steel
General requirements EN 14399-1a
Tolerance 6gb
Thread
International Standards ISO 261, ISO 965-2
Property class 8.8 or 10.9
Mechanical properties
European Standard EN ISO 898-1
Value KV,min = 27 J at -20 °C
Impact strength Test specimenc ISO 148-1
Test EN 10045-1
Product grade C except:
dimension r.
Tolerances Tolerance for lengths ≥ 160 mm ± 4,0 mm
International Standard EN ISO 4759-1
Normal as processede
Surface finishd hot dip galvanized EN ISO 10684
Others to be agreedf
Limits for surface discontinuities are covered in
Surface discontinuities
EN 26157-1.
Acceptability For acceptance procedure, see EN ISO 3269.
a For the time being EN 14399-1 refers only to EN 14399-3 and EN 14399-4 as far as dimensions and mechanical charac-
teristics of the components and functional characteristics of the assemblies are concerned. Such references shall also
apply to EN 14399-7.
b The tolerance class specified applies without surface finish. Hot-dip galvanized bolts are intended for assembly with
oversize tapped nuts.
c The preparation of the test specimens with V-notch in the fastener shall be as specified in EN ISO 898-1.
d Attention is drawn to the need to consider the risk of hydrogen embrittlement in the case of bolts of property class 10.9,
when selecting an appropriate surface treatment process (e.g. cleaning and coating), see the relevant coating
standards.
e "As processed" means the normal finish resulting from manufacture with a light coating of oil.
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
f Other coatings may be negotiated between the purchaser and the manufacturer provided they do not impair
the mechanical properties or the functional characteristics. Coatings of cadmium or cadmium alloy are not permitted.
4.4 Marking of bolts
High-strength structural countersunk bolts according to this part of this European Standard shall be marked with:
a) property class marking in accordance with EN ISO 898-1 and the letters HR.
EXAMPLE 1 10.9 HR
b) the identification mark of the manufacturer of the assembly.
It is permissible for the marking to be either embossed or indented on the top surface of the head.
EXAMPLE 2 of bolt marking (see Figure 2):

11

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Key
1 identification mark of the manufacturer of the assembly
Figure 2 — Example for marking of a bolt
5 Nuts
NOTE This nut is identical with the nut specified in EN 14399-3.
5.1 Dimensions of nuts
See Figure 3 and Table 4.
Alternative form
permissible
a 15° to 30°
b 110° to 130°
Figure 3 — Dimensions of nuts
12
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Table 4 — Dimensions of nuts a
Thread d M12 (M14)b M16 (M18)b M20 M22 M24 M27 M30 M36
Pc 1,75 2 2 2,5 2,5 2,5 3 3 3,5 4

da max. 13 15,1 17,3 19,5 21,6 23,7 25,9 29,1 32,4 38,9
min. 12 14 16 18 20 22 24 27 30 36
max. d d d d d d d d d d
dw
min. 20,1 21,86 24,9 27,70 29,5 33,3 38,0 42,8 46,6 55,9
e min. 23,91 27,12 29,56 32,95 35,03 39,55 45,20 50,85 55,37 66,44
max. 10,8 12,8 14,8 15,8 18 19,4 21,5 23,8 25,6 31
m
min. 10,37 12,1 14,1 15,1 16,9 18,1 20,2 22,5 24,3 29,4
mw min. 8,3 9,7 11,3 12,1 13,5 14,5 16,2 18,1 19,5 22,4
max. 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8
c
min. 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4
max. 22 24 27 30 32 36 41 46 50 60
s
min. 21,16 23,16 26,16 29,16 31 35 40 45 49 58,8
t 0,38 0,42 0,47 0,52 0,58 0,63 0,72 0,80 0,87 1,05
a For hot dip galvanized nuts the above dimensions apply before galvanizing.
b Non-preferred sizes.
c P is the pitch of thread.
d d
w max. = sactual.
13
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
5.2 Specification for nuts and reference standards
Table 5 — Specifications for nuts and reference standards
Material Steel
General requirements EN 14399-1a
Tolerance 6H or 6AZ
Thread
International Standards ISO 261, ISO 965-2, ISO 965-5
Property class 8b or 10b
Mechanical properties
European Standard EN 20898-2
Product grade B except dimensions m and d
Tolerances
International Standard EN ISO 4759-1c
Normal as processedd
Surface finish hot dip galvanized EN ISO 10684
Others to be agreede
Limits for surface discontinuities are covered in
Surface discontinuities
EN ISO 6157-2.
Acceptability For acceptance procedure, see EN ISO 3269.
a For the time being EN 14399-1 refers only to EN 14399-3 and EN 14399-4 as dimensions and mechanical
characteristics of the components and functional characteristics of the assembly are concerned. Such references
shall also apply to EN 14399-7.
b For proof load values, see 4.3. All other mechanical properties as specified in EN 20898-2.
c Except tolerance of total run-out t of bearing face, see Table 4.
d "As processed" means the normal finish resulting from manufacture with a light coating of oil.
e Other coatings may be negotiated between the purchaser and the manufacturer provided they do not impair the
mechanical properties or the functional characteristics. Coatings of cadmium or cadmium alloys are not permitted.
14 --`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
5.3 Proof load values of nuts
Table 6 — Proof load values of nuts
Property class
Nominal stress
area of standard 8 10
Thread test mandrel
d As Tolerance class Tolerance class
6H or 6AZ 6H or 6AZ
mm2 Proof load (As × Sp), N
M12 84,3 84 300 97 800

(M14) 115 115 000 133 400
M16 157 157 000 182 100
(M18) 192 192 000 222 700
M20 245 245 000 284 200
(M22) 303 303 000 351 200
M24 353 353 000 409 500
(M27) 459 459 000 532 400
M30 561 561 000 650 800
M36 817 817 000 947 700
The proof load values are based on the following stresses under proof load:
— for nuts of property class 8: 1 000 MPa

— for nuts of property class 10: 1 160 MPa
Where nuts are to be accepted on the basis of hardness values, the appropriate limits shall be those given in Table 7.
Table 7— Hardness values of nuts, if specified
Nut Hardness limits
property class 8, tolerance class 6H as specified in EN 20898-2 for property class 8
property class 10, tolerance class 6H or 6AZ as specified in EN 20898-2 for property class 10
property class 8, tolerance class 6AZ, hot dip 260 HV to 353 HV (24 HRC to 36 HRC)
galvanized
5.4 Decarburization of the nut thread
The decarburization of the nut thread, when measured in analogy to external threads as given in EN ISO 898-1, shall
not exceed G = 0,015 mm.
15
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
5.5 Marking of nuts
High-strength structural nuts according to this part of this European Standard shall be marked with:
a) property class marking in accordance with EN 20898-2 and the letters HR.
EXAMPLE 1 10 HR
b) the identification mark of the manufacturer of the assembly.
The marking shall be indented on either the top or bottom face of chamfered nuts and shall be either indented or
embossed on the non-bearing face of washer faced nuts.
EXAMPLE 2 of nut marking (see Figure 4):
Key
1 identification mark of the manufacturer of the assembly
Figure 4 — Example for marking of a nut
6 Designation of the countersunk head bolt/nut assembly

EXAMPLE 1 Designation of an assembly for high strength structural bolting, system HR, consisting of a countersunk head
bolt with thread M16, nominal length l = 80 mm and property class 10.9 and a hexagon nut with large width across flats, with
thread M16 and property class 10:
Countersunk head bolt/nut assembly EN 14399-7 — M16 x 80 — 10.9/10 — HR
If surface finishes other than "as processed" are required, the specified surface finish shall be added to the designation.
If countersunk head bolts according to this part of this European Standard are required for other purposes, they may be ordered
separately and shall then be designated as follows:
EXAMPLE 2 Designation of a countersunk head bolt with thread M16, nominal length l = 80 mm and property class 10.9:
Countersunk head bolt EN 14399-7 — M16 × 80 — 10.9 — HR
7 Associated washers
Bolt/nut assemblies according to this part of this European Standard shall be assembled with washers according to
EN 14399-5 or according to EN 14399-6.
16 --`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
8 Functional characteristics of the bolt/nut/washer(s) assembly
8.1 General
The functional characteristics of the bolt/nut/washer(s) assembly according to 8.2 to 8.5 shall be achieved when
tested in accordance with EN 14399-2. For testing countersunk head bolts an adapter as shown in Table 8, Figure
5 and Figure 6 shall be used under the bolt head.
Four full threads (in addition to the thread run out) shall remain clear between the bearing surface of the nut and
the unthreaded part of the shank.
NOTE For further background information as to these functional characteristics see EN 14399-2.
Table 8 — Characteristics of adapters

Nominal bolt diameter Hole diameter Outside diameter Hardness for the Parallelism
adapters
M12 ≤ d ≤ M24 d + 2 mm Not less than 3d and suffi- 45 HRC to 50 HRC ≤1%
cient to distribute load ade- through hardened
d > M24 d + 3 mm quately to the device
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
Figure 5 — Adapter
There shall be sufficient suitable lubricant on the nuts or on the bolts and washers in the as delivered conditions, to
ensure that seizure will not take place on tightening the assembly and that the required preload is obtained, see Fig-
ure 6.
17

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Key
1 nut (turned during tightening)

2 washer of the assembly (prevented from rotating)
3 shim(s)
4 calibrated bolt force measuring device
5 adapter
6 bolt head (prevented from rotating by using the screwdriver slot, if necessary)
a clamp length Σt
Figure 6 — Test set-up
8.2 Individual value of the maximum bolt force during the tightening test (Fbi max)
The following applies:
Fbi max ≥ 0,9 fub × As (1)
where
fub is the nominal tensile strength (Rm);

As is the nominal stress area of the bolt;
Fbi max is the individual value of the maximum bolt force reached during the tightening test.
18 --`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN 14399-7:2007
EN 14399-7:2007 (E)
8.3 Angle by which the nut has to be turned starting from a preload of 0,7 fub × As until
Fbi max is reached (∆Θ1)
The values specified in Table 9 are for information only.
Table 9 — Values for ∆Θ1
Clamp length ∆Θ1

Σ ta min.
Σ t < 2,5 d 90°

2,5 d ≤ Σ t < 6 d 120°
6 d ≤ Σ t ≤ 10 d 150°
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
a The clamp length Σ t is the total thickness of the clamped parts including the washer and the adapter.
8.4 Angle by which the nut has to be turned starting from a preload of 0,7 fub × As until
Fbi has dropped again to 0,7 fub × As (∆Θ2)
The values for ∆Θ2 specified in Table 10 apply.
Table 10 — Values for ∆Θ2
Clamp length ∆Θ2

Σ ta min.
Σ t < 2,5 d 210°

2,5 d ≤ Σ t < 6 d 240°
6 d ≤ Σ t ≤ 10 d 270°
a The clamp length Σ t is the total thickness of the clamped parts including the washer and the adapter.
8.5 Individual values of the k-factor (ki), mean value of the k-factor (km) and coefficient of
variation of the k-factor (Vk)
8.5.1 Individual values of the k-factor (ki) for k-class K1
When ki-values are required, they shall be in the range of 0,10 ≤ ki ≤ 0,16.
8.5.2 Mean value of the k-factor (km) and coefficient of variation of the k-factor (Vk) for k-class K2
Mean value of the k-factor is given by
∑ ki
i =1
km = (2)
n
with
19

BS EN 14399-7:2007
EN 14399-7:2007 (E)
Mi
k= (3)
Fp × d
where
Mi is the individual value of the torque applied;

Fp is the specified preload;
d is the nominal bolt diameter.
For the coefficient of variation of the k-factor (Vk) the following applies:
sk
Vk = (4)
km
where
 Σ (ki − km ) 2 
sk is the standard deviation  sk = 
 (5)
 n −1
 
When km and Vk are required, the following values apply:
0,10 ≤ km ≤ 0,23
Vk ≤ 0,10
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---
20
BS EN 14399-7:2007
EN 14399-7:2007 (E)
Bibliography
[1] prEN 1090-2, Execution of steel structures and aluminium structures — Part 2: Technical requirements for the
execution of steel structures
21
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---

BS EN
14399-7:2007
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL
--`,,,,`,,``,,`,`,`,```,`,,,,``,-`-`,,`,,`,`,,`---


BS en 14399-7-2007 (2010)

Uploaded by

Copyright:

Available Formats

BS en 14399-7-2007 (2010)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BS en 14399-7-2007 (2010)

Uploaded by

Copyright:

Available Formats

BRITISH STANDARD BS EN

This British Standard is the UK implementation of EN 14399-7:2007.

14399-3:2005 and BS EN 14399-4:2005.

This British Standard was Amendments/corrigenda issued since publication

ISBN 978 0 580 69003 7

Copyright British Standards Institution

High-strength structural bolting assemblies for preloading - Part

Boulonnerie de construction métallique à haute résistance Hochfeste planmäßig vorspannbare

This European Standard was approved by CEN on 10 November 2007.

EUROPEAN COMMITTEE FOR STANDARDIZATION

Management Centre: rue de Stassart, 36 B-1050 Brussels

Copyright British Standards Institution

Figure 2 — Example for marking of a bolt ..................................................................................................................12

Figure 3 — Dimensions of nuts ..................................................................................................................................12

Figure 4 — Example for marking of a nut ...................................................................................................................16

Figure 6 — Test set-up ...............................................................................................................................................18

Table 1 — Systems of bolt/nut/washer(s) assemblies..................................................................................................4

Table 2 — Dimensions of boltsa ...................................................................................................................................8

Table 3 — Specifications for bolts and reference standards ......................................................................................11

Table 4 — Dimensions of nuts a .................................................................................................................................13

Table 5 — Specifications for nuts and reference standards.......................................................................................14

Table 6 — Proof load values of nuts...........................................................................................................................15

Table 7 — Hardness values of nuts, if specified ........................................................................................................15

Table 8 — Characteristics of adapters .......................................................................................................................17

Table 9 — Values for ∆Θ1 ..........................................................................................................................................19

Table 10 — Values for ∆Θ2 ........................................................................................................................................19

Copyright British Standards Institution

Copyright British Standards Institution

Table 1 — Systems of bolt/nut/washer(s) assemblies

 testing for conformity evaluation;

This document gives requirements for:

 associated washer(s) according to EN 14399-5 or to EN 14399-6;

 performance and suitability tests;

 nut height according to style 1 (see EN ISO 4032),

 thread length of the bolt according to ISO 888.

EN 1993-1-8, Eurocode 3: Design of steel structures — Part 1-8: Design of joints

EN 10045-1, Metallic materials - Charpy impact test - Part 1: Test method

Copyright British Standards Institution

EN ISO 3269, Fasteners - Acceptance inspection (ISO 3269:2000)

EN ISO 6157-2, Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995)

EN ISO 10684, Fasteners - Hot dip galvanized coatings (ISO 10684:2004)

3 Terms and definitions

4.2 Dimensions of bolts

See Figure 1 and Table 2.

The difference between lg and ls shall not be less than 1,5 P.

Figure 1 — Dimensions of bolts

Copyright British Standards Institution

Thread d M12 (M14)b M16 (M18)b M20

75 73,5 76,5 36,25 45 31 41 27 37 21 28,5 23 30,5

Copyright British Standards Institution

4.3 Specification for bolts and reference standard

Table 3 — Specifications for bolts and reference standards

4.4 Marking of bolts

b) the identification mark of the manufacturer of the assembly.

EXAMPLE 2 of bolt marking (see Figure 2):

Copyright British Standards Institution

1 identification mark of the manufacturer of the assembly

Figure 2 — Example for marking of a bolt

5.1 Dimensions of nuts