Scribd
Upload
70 views3 pages

BT-7/M-20 Non-Conventional Machining ME-415N: Roll No. .......................... Total Pages: 03

This 3-page document contains instructions for a non-conventional machining exam with 8 questions across 4 units. It provides details on the exam such as the total pages, roll number, time allotted, and maximum marks. It lists the 8 exam questions, which cover topics like the advantages of non-conventional machining, ultrasonic machining, electrochemical machining, electrodischarge machining, abrasive jet machining, electron beam machining, laser beam machining, and rapid prototyping processes. Students are instructed to attempt 5 questions total, selecting at least one from each unit.

Uploaded by

upender
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views3 pages

BT-7/M-20 Non-Conventional Machining ME-415N: Roll No. .......................... Total Pages: 03

This 3-page document contains instructions for a non-conventional machining exam with 8 questions across 4 units. It provides details on the exam such as the total pages, roll number, time allotted, and maximum marks. It lists the 8 exam questions, which cover topics like the advantages of non-conventional machining, ultrasonic machining, electrochemical machining, electrodischarge machining, abrasive jet machining, electron beam machining, laser beam machining, and rapid prototyping processes. Students are instructed to attempt 5 questions total, selecting at least one from each unit.

Uploaded by

upender
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Roll No. ..........................

Total Pages : 03

BT-7/M-20 37168
NON-CONVENTIONAL MACHINING
ME-415N
Time : Three Hours] [Maximum Marks : 75

Note : Attempt Five questions in all, selecting at least one

question from each Unit.

Unit I

1. Enumerate the advantages of ‘Non-conventional

machining’ processes ? Describe various considerations

involved in selection of non-conventional machining

process for a particular application. 15

2. (a) If suppose USM is used for drilling a hole (under

the same machining conditions) in Aluminium and

Cast Iron. Which one will have higher depth of the

drilled hole and why ? 10

(b) Explain the functions of ‘Horn’ in USM. 5

(3)L-37168 1
Unit II

3. What is the self-adjusting feature in ECM ? Describe


various functions served by an electrolyte in ECM. List
the common electrolytes used in ECM. 15

4. (a) Explain the following terms related to EDM : 10


(i) Gap Flushing
(ii) W/T Ratio
(iii) Duty factor
(iv) Cycle time.
(b) Describe various applications of EDM process. 5

Unit III

5. (a) What is mixing ratio ? Explain the importance of


maintaining an optimum mixing ratio in Abrasive
jet machining. 10
(b) Sketch and explain any one type of plasma torch. 5

6. (a) Explain, why vacuum is needed in Electron beam


process and explain the method to protect work
table from getting damaged by the electron beam
which has completely penetrated the workpiece. 10
(b) Explain the effect of ‘focusing’ on the performance
of laser beam machining. 5

(3)L-37168 2
Unit IV

7. Illustrate with a neat diagram the process chain involved


in the rapid prototyping process. Describe advantages,
limitations and application of RP process. 15

8. (a) Make a neat sketch of FDM process. Mark all the


components and parts on the diagram. 5
(b) Illustrate various steps involved in Stereolithography
Apparatus Operation. 5
(c) What is the material used to form a prototype in
LOM process ? In what form the material is fed
into the system ? 5

(3)L-37168 3 ___

You might also like