Scribd
Upload
168 views5 pages

Inter Vlan Routing Through L3 Switch

The document describes configuring inter-VLAN routing on a switch. It shows the configuration of VLANs 10 and 20 on the switch, assigning each VLAN an IP address. It also shows enabling IP routing globally on the switch and verifying connectivity between the VLANs.

Uploaded by

Syed Mohammad Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
168 views5 pages

Inter Vlan Routing Through L3 Switch

The document describes configuring inter-VLAN routing on a switch. It shows the configuration of VLANs 10 and 20 on the switch, assigning each VLAN an IP address. It also shows enabling IP routing globally on the switch and verifying connectivity between the VLANs.

Uploaded by

Syed Mohammad Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Inter vlan routing through L3 switch

Switch config

Crete vlans ky bad say

% Invalid input detected at '^' marker.


switch1(config)#exit
switch1#
%SYS-5-CONFIG_I: Configured from console by console

switch1#con
switch1#con
% Ambiguous command: "con"
switch1#conf
switch1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
switch1(config)#in
switch1(config)#interface g1/0/4
switch1(config-if)#sw
switch1(config-if)#switchport mo
switch1(config-if)#switchport mode ac
switch1(config-if)#switchport mode access
switch1(config-if)#sw
switch1(config-if)#switchport ac
switch1(config-if)#switchport access vl
switch1(config-if)#switchport access vlan 20
switch1(config-if)#exit
switch1(config)#sh
switch1(config)#sh
switch1(config)#sh in
switch1(config)#^Z
switch1#
%SYS-5-CONFIG_I: Configured from console by console

switch1#sh in
switch1#sh interfaces vl
switch1#sh interfaces vlan
% Incomplete command.
switch1#sh
switch1#show vl
switch1#show vlan int
switch1#show vlan int
^
% Invalid input detected at '^' marker.
switch1#sh
switch1#show int
switch1#show interfaces vl
switch1#show interfaces vlan
% Incomplete command.
switch1#show interfaces vlan br
switch1#show interfaces vlan br
^
% Invalid input detected at '^' marker.
switch1#sh
switch1#show vl
switch1#show vlan br
switch1#show vlan brief

VLAN Name Status Ports


---- -------------------------------- --------- -------------------------------
1 default active Gig1/0/5, Gig1/0/6, Gig1/0/7, Gig1/0/8
Gig1/0/9, Gig1/0/10, Gig1/0/11, Gig1/0/12
Gig1/0/13, Gig1/0/14, Gig1/0/15, Gig1/0/16
Gig1/0/17, Gig1/0/18, Gig1/0/19, Gig1/0/20
Gig1/0/21, Gig1/0/22, Gig1/0/23, Gig1/0/24
Gig1/1/1, Gig1/1/2, Gig1/1/3, Gig1/1/4
10 HR active Gig1/0/1, Gig1/0/2
20 Sales active Gig1/0/3, Gig1/0/4
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
switch1#conf
switch1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
switch1(config)#int
switch1(config)#interface vl
switch1(config)#interface vlan 10
switch1(config-if)#
%LINK-5-CHANGED: Interface Vlan10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up

switch1(config-if)#ip add
switch1(config-if)#ip address 10.1.1.1 255.255.255.0
switch1(config-if)#no sh
switch1(config-if)#no shutdown
switch1(config-if)#
switch1(config-if)#^Z
switch1#
%SYS-5-CONFIG_I: Configured from console by console

switch1#conf
switch1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
switch1(config)#int
switch1(config)#interface vl
switch1(config)#interface vlan 20
switch1(config-if)#
%LINK-5-CHANGED: Interface Vlan20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up

switch1(config-if)#ip add
switch1(config-if)#ip address 20.1.1.1 255.255.255.0
switch1(config-if)#no sh
switch1(config-if)#no shutdown
switch1(config-if)#^Z
switch1#
%SYS-5-CONFIG_I: Configured from console by console

switch1#sh
switch1#show ip int br
switch1#show ip int brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet1/0/1 unassigned YES unset up up
GigabitEthernet1/0/2 unassigned YES unset up up
GigabitEthernet1/0/3 unassigned YES unset up up
GigabitEthernet1/0/4 unassigned YES unset up up
GigabitEthernet1/0/5 unassigned YES unset down down
GigabitEthernet1/0/6 unassigned YES unset down down
GigabitEthernet1/0/7 unassigned YES unset down down
GigabitEthernet1/0/8 unassigned YES unset down down
GigabitEthernet1/0/9 unassigned YES unset down down
GigabitEthernet1/0/10 unassigned YES unset down down
GigabitEthernet1/0/11 unassigned YES unset down down
GigabitEthernet1/0/12 unassigned YES unset down down
GigabitEthernet1/0/13 unassigned YES unset down down
GigabitEthernet1/0/14 unassigned YES unset down down
GigabitEthernet1/0/15 unassigned YES unset down down
GigabitEthernet1/0/16 unassigned YES unset down down
GigabitEthernet1/0/17 unassigned YES unset down down
GigabitEthernet1/0/18 unassigned YES unset down down
GigabitEthernet1/0/19 unassigned YES unset down down
GigabitEthernet1/0/20 unassigned YES unset down down
GigabitEthernet1/0/21 unassigned YES unset down down
GigabitEthernet1/0/22 unassigned YES unset down down
GigabitEthernet1/0/23 unassigned YES unset down down
GigabitEthernet1/0/24 unassigned YES unset down down
GigabitEthernet1/1/1 unassigned YES unset down down
GigabitEthernet1/1/2 unassigned YES unset down down
GigabitEthernet1/1/3 unassigned YES unset down down
GigabitEthernet1/1/4 unassigned YES unset down down
Vlan1 unassigned YES unset administratively down down
Vlan10 10.1.1.1 YES manual up up
Vlan20 20.1.1.1 YES manual up up
switch1#%IP-4-DUPADDR: Duplicate address 10.1.1.1 on Vlan10, sourced by
0060.70B6.6A8D

switch1#sh
switch1#show ip
switch1#show ip rou
switch1#show ip route
Default gateway is not set

Host Gateway Last Use Total Uses Interface


ICMP redirect cache is empty

switch1#
switch1#cong
switch1#conf
switch1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
switch1(config)#ip rou
switch1(config)#ip rout
switch1(config)#^Z
switch1#
%SYS-5-CONFIG_I: Configured from console by console

switch1#
switch1#conf
switch1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
switch1(config)#ip routing
switch1(config)#exit
switch1#
%SYS-5-CONFIG_I: Configured from console by console

switch1#sh
switch1#show ip
switch1#show ip ro
switch1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/24 is subnetted, 1 subnets


C 10.1.1.0 is directly connected, Vlan10
20.0.0.0/24 is subnetted, 1 subnets
C 20.1.1.0 is directly connected, Vlan20

You might also like