Scribd
Upload
87 views3 pages

GEC 1101 - Engineering Graphics: Tutorial-Module - 3 Projection of Straight Lines and Planes

This document provides 15 problems involving the projection of straight lines and planes. The problems involve drawing projections of lines and planes given information about their positions in space, such as the locations of endpoints, lengths, inclinations, and views. The problems require calculating true lengths, inclinations, locating traces, and determining unknown angles or dimensions.

Uploaded by

G. Rajesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
87 views3 pages

GEC 1101 - Engineering Graphics: Tutorial-Module - 3 Projection of Straight Lines and Planes

This document provides 15 problems involving the projection of straight lines and planes. The problems involve drawing projections of lines and planes given information about their positions in space, such as the locations of endpoints, lengths, inclinations, and views. The problems require calculating true lengths, inclinations, locating traces, and determining unknown angles or dimensions.

Uploaded by

G. Rajesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

GEC 1101 – Engineering Graphics

Tutorial-Module – 3 Projection of straight lines and planes

1. A line AB measuring 80 mm is inclined at an angle of 30° to HP and 45°to VP. Point A


is 20 mm above HP and 30 mm in front of VP. Draw the projection of the straight line.
Also mark the traces.

2. A line PQ, 80 mm long has its end P, 10 mm above HP and 15 mm in front of VP. The
other end Q is 65 mm above HP and 50 mm in front of VP. Draw the projection of the
line and find its true inclination with HP and VP.

3. A line AB, has its end A, 10 mm above HP and 15 mm in front of VP. The other end Q
is 65 mm above HP and 50 mm in front of VP. Draw the projection of the line and find
its true inclination with HP and VP if the distance between the end projectors is 40
mm.

4. A line MN, 60 mm long has its end M 30 mm above HP and 25 mm in front of VP. The
top view and front view measure 40 mm and 55 mm respectively. Draw its projections
and mark the traces.

5. The end A of a line AB is 10 mm in front of VP and 20 mm above HP. The line is


inclined at 30° to HP and front view is 45° with XY. Top view is 60 mm long. Draw the
projections. Find the true length and true inclination with VP. Locate the traces.

6. One end A of a line AB, 75 mm long is 20 mm above HP and 25 mm in front of VP.


The line is inclined at 30° to HP and the top view makes 45° with XY. Draw the
projections of the line and find the true inclination with the vertical plane.

7. The end P of a line PQ, 70 mm long is 15 mm above HP and 20 mm in front of VP.


Q is 40 mm above HP. Its top view makes an angle of 45° to XY. Draw the projections
of the line and find its true inclinations with VP and HP.

8. The mid-point M of a straight line AB is 60 mm above HP and 50 mm in front of VP.


The line measures 80 mm and inclined at an angle of 30° to HP and 45° to VP. Draw
its projections.

9. End A of a line AB is 15 mm above HP and 20 mm in front of VP .The front view and


top view measures 50 mm and 60 mm. The distance between the end projectors is 50
mm. Draw the projections and find true inclination and true length by the following two
methods. (i) Rotating line method (ii) Trapezoidal plane method
GEC 1101 – Engineering Graphics

10. A line AB has end A on HP and end B in VP. The front view and top view measure
90 mm and 70 mm respectively. The front view makes an angle of 50° with XY. Draw
the projections and find the true length and true inclination of the line.

11. A rectangular plate of side 50 mm × 25 mm is resting on its shorter side on HP and


inclined at 30° to VP. Its surface is inclined at 60° to HP. Draw its projections.

12. A pentagon of side 30 mm rests on the ground on one of its corners with the sides
containing the corner being equally inclined to the ground .The side opposite to the
corner on which it rests is inclined at 30° to VP and is parallel to HP. The surface of
the pentagon makes 50° with the ground. Draw its projections.

13. A hexagonal plate of side 30 mm is resting with one of its sides in VP and inclined at
40° to HP. Its surface is inclined at 35°to VP. Draw its projections.

14. A circular lamina of 60 mm diameter rests on HP on a point 1 on the circumference.


The lamina is inclined to HP such that the top view of it is an ellipse of minor axis 35
mm. The top view of the diameter through the point 1 makes an angle of 45°with VP.
Draw the projections and determine the angle made by the lamina with HP.

15. A rectangular plate of side 50 mm × 25 mm is resting on its shorter side on HP and


inclined at 30° to VP. Its surface is inclined HP in such a way that the top view is a
perfect square. Draw its projections and find the surface inclination to HP.
GEC 1101 – Engineering Graphics

You might also like