Working between the

hook and the load

2014 Product Catalogue

for UK & ROW
Safe Lifting Solutions
Email: [email protected] www.modulift.com
 Contents
27
Modulift Sets 03 Mod 250/300
Mod 600XA/400 34 28
Modulift UK Ltd
Modulift Spreader Beams 04 Mod 250/400
MOD 600XA/500 35 29
11 New Fields Business Park
One Beam Many Lifts 05 MOD 250/110H
MOD Hybrid
600XA/600 36 30 Stinsford Road, Poole
Dorset BH17 0NF
The Standard Range 06 MOD 250/110
MOD Hybrid
600XA/800 37 31

The Heavy Range 07 MOD 250/70H

MOD Hybrid
600XB/500 38 32
Tel: +44 (0) 1202 621511
Regs, Standards & Compliance 08 MOD 250/70
MOD Hybrid
600XB/800 39 33 Fax: +44 (0) 1202 632811
Email: [email protected]
Enhanced QA/Custom Design 09 Mod 400/400
MOD 600 B/1000 40 34
Web: www.modulift.com
Accessories 10 Mod 400/500 41

Design Engineering & Lift Mod 400/600 42

Management 12
MOD 400/250 Hybrid 43
QuickJoint 2 15
MOD 400/110SH Hybrid 44
Mod 6 16
MOD 400/110H Hybrid 45
Mod 12 17
MOD 400/110 Hybrid 46
Mod 24 18
MOD 600XB/400 47
Mod 34 19
MOD 600 XB/600 48
Mod 50 20
MOD 600 XB/800 49
MOD 50/24 Step-Downs 21
MOD 600 XB/1000 50
MOD 50/12 Step-Downs 22
MOD 800J/1000 51
MOD 50/6 Step-Downs 23
CMOD Spreader Frame Range 52
Mod 70 24
CMOD 6 53
Mod 70H 25
CMOD 12 54
MOD 70/34 Step-Downs 26
CMOD 24 55
MOD 70/24 Step-Downs 27
CMOD 34 56
Mod 110 28
CMOD 50 57
Mod 110H 29
CMOD 70 58 Lattice SF 30m 63
Mod 110SH 30
CMOD & Beyond 59 Lattice SF 33m 64
MOD 110/70 Step-Downs 31
Lattice Spreader Beams 60 Lattice SF 36m 65
MOD 110/50 Step-Downs 32
Lattice SF 6-24m 61 Lattice SF 42m 66
Mod 250/250 33
Lattice SF 27m 62 Where To Buy & Contacts 67

2 Email: [email protected] www.modulift.com

 Modulift Sets

The most cost efficient way to

purchase the Modulift System is in
the predetermined sets. This will allow
you to interchange components in
each set to gain the full range of spans
available. This table shows the basic
product range and gives you a quick
guide to their specification and retail
price.

The remainder of this catalogue will

look at the full range of products and
support services in more detail. If the
information you need is not within
these pages then pick up the phone or
send us an email we will be pleased to
help you.

Standard Heavy
QJ2 MOD 34 MOD 110 MOD 250/300 MOD 400/600
Up to 2t at 1.2m/4ft Up to 34t at 5m/17ft Up to 110 t at 11m/37ft Up to 300t at 12m/40ft Up to 600t at 12m/40ft
Up to 8m/26ft at a Up to 16m/52ft at a Up to 20m/66ft at a Up to 23m/76ft at a
lower capacity. lower capacity. lower capacity. lower capacity.

MOD 6 MOD 50 MOD 110H MOD 250/400 MOD 600/600

Up to 6t at 2.5m/8ft Up to 50t at 7.5m/25ft Up to 170t at 8m/26ft Up to 400t at 8m/28ft Up to 600t at 21m/70ft
Up to 11m/36’ft at a Up to 16m/52ft at a Up to 20m/66ft at a Up to 26m/85ft at
lower capacity. lower capacity. lower capacity. a lower capacity.

MOD 12 MOD 70 MOD 110SH MOD 400/400 MOD 600/800

Up to 12t at 4m/13ft Up to 70t at 9m/29ft Up to 240t at 6m/20ft Up to 400t at 16m/55ft Up to 800t at 18m/60ft
Up to 12m/40’ft at a Up to 16m/52ft at a Up to 23m/76ft at a Up to 26m/85ft at
lower capacity. lower capacity. lower capacity. a lower capacity.

MOD 24 MOD 70H MOD 250/250 MOD 400/500 MOD 600/1000

Up to 24t at 4.5m/14ft Up to 100t at 8m/25ft Up to 250t at 13m/45ft Up to 500t at 14m/47ft Up to 1000t at 15m/51ft
Up to 6m/20ft at a Up to 12m/40ft at a Up to 20m/66ft at a Up to 23m/76ft at a and up to 26m/85ft at a
lower capacity. lower capacity. lower capacity. lower capacity. lower capacity.

Email: [email protected] www.modulift.com 3

 Modulift Spreader Beams

Modulift offer a wide range of

Modular Spreader Beam components, Part of the Modulift Standard Range
offering a variety of different
spans for all your lifting needs.

The sizes range from 2 to MOD 70/70H

5,000t with spans available
from 0.4m/1’4” - 100m/300’

The flexibility of the modular

MOD 50
configuration enables our Spreader
Beams to be reused time and time
again, providing a cost-effective
solution. MOD 34

What Size Beam Do I Need?

Simple! First select the span MOD 24
you require, then select the
SWL you need for that span.
Please see tables on pages 6 & 7 MOD 12

to select your beam.

MOD 6

Part of the Modulift Heavy Range

Range Classification

Range Modulift Sizes

MOD 600
Standard 6, 12, 24, 34, 50, 70, 70H

Heavy 110, 110H, 110SH, 250, 400, 600

MOD 400

MOD 250

MOD 110SH

MOD 110/110H

4 Email: [email protected] www.modulift.com

 One Beam Many Lifts

Interchangeable Components
For Larger Lighter Loads
For longer spans and lighter loads, additional components are available allowing you to optimise the weight of our higher
capacity range of Modular Spreader Beams to carry out these lifts. These struts provide the backbone of our Spreader
Beams when trying to achieve longer spans. We have two solutions that can make the system more flexible and cheaper for
you by interchanging smaller capacity End Units and Drop Links.

• Step-Down End Units are designed for smaller sizes, up to the MOD 70
• Cone Adaptors accommodate the larger sizes

These additional components allow your existing Spreader Beam to become even more versatile over a number of lifts so
you can remain cost-effective with your rigging and crane capacity requirements.

By stepping down the End Units to a more suitable capacity, you can optimise your Shackles and Slings to provide a lighter
system overall.

There are a number of ways you can utilise our Modular Spreader Beams, for example;

Need a span of 20m/66’ but are only lifting 70t - we can provide you with a MOD 250/70 giving you Cone Adapters and
MOD 70 End Units to bolt to MOD 250 struts to achieve the required overall Spreader Beam system.

Need to lift 24t but at 12m/40’ - change our standard MOD 70 Spreader Beam End Units to Step-Down End Units and
decrease the SWL to 24t allowing you to use smaller Shackles and Slings with the MOD 70 struts.

Need to lift 100t– if you already have a MOD 70 Spreader Beam, by changing the End Units to the MOD 70H End Units you
can increase the SWL to 100t negating the need to buy a completely brand new Spreader Beam.

Using one of our Modular Spreader Beams enables you to be more flexible over a number of lifts without needing
to buy a new Spreader Beam every time, our lightweight design also minimises the overall weight of the lifting
equipment and the costs incurred whilst working between the hook and the load.

Email: [email protected] www.modulift.com 5

 The Standard Range

Load v Span Load  

Chart<-  SModulift
pan  =  >Spreader
od?@AB  SBeam
tandard   Cange  Range
Standard

100  

95  

90  

85   MOD 70H
Sling Angle Format
80  

ISA
75  

70  
ISA / 30° STV

STV

BSA
65  

MOD 70
60  
/ 60°

55  
BSASTV  
degree    

50  
60°

45  
 30  
ISA  /@

MOD 50
tonnes

40  
MOD 24
/  60  d/egree  

35  
SWL

30  
SWL  /  tonnes  @  30  degrees  BSA  

MOD 34
25  

20  
MOD 24
15   MOD 34
10   TOP: 25t
MOD 12
LOWER: 17t
5  
MOD 6
0  
0.5   1   1.5   2   2.5   3   3.5   4   4.5   5   5.5   6   6.5   7   7.5   8   8.5   9   9.5   10   10.5   11   11.5   12  
Span (m)
Span   (m)  
MOD 50

Components per Set TOP: 35t

LOWER: 25t
* Please note: Custom length Struts are available on request
strut
spreader system 0.1m 0.2m 0.25m 0.3m 0.5m 0.6m 0.75m 1.0m 1.5m 2.0m 3.0m 4.0m 6.0m end drop
unit link
MOD 6 1 1 1 1 1 2 2
MOD 12 1 1 1 1 1 2 2
MOD 24 1 1 2 2 2
MOD 34 1 1 3 2 2
MOD 50 1 1 1 2 2 2
MOD 70/70H 1 1 1 2 2 2
MOD 110/110H/110SH 1 1 1 3 2 2
MOD 250-250/250-300/250-400 1 1 1 2 2 2
MOD 400-400/400-500/400-600 1 1 1 3 2 2
MOD 600-600/600-800/600-1000 1 1 1 3 2 2

6 Email: [email protected] www.modulift.com

 The Heavy Range

Load v Span ChartLoad   <  Span  

- Modulift =  >od?@AB  
Spreader Beam Cea<D  
HeavyERange
ange  
1000  
975  
950  
925  
900   MOD 600/1000
875  
850  
825   Sling Angle Format
800  
775  
750   ISA
SWL  /  tonnes  @  30  degrees  BSA  /  60  degree  ISA  /  30  degree  STV    

725  
700   MOD 600/800
SWL / tonnes @ 60° BSA / 60° ISA / 30° STV

675   STV
650   BSA
625  
600  
575  
550   MOD 400/600 MOD 600/600
525  
500  
475  
450   MOD 400/500
425  
400  
375  
350   MOD 250/400 MOD 400/400
325  
300  
275   MOD 250/300
250  
225  
200   MOD 110SH MOD 250/250
175  
150  
MOD 110H
125  
100  
75  
50   MOD 110
25  
0  
2   3   4   5   6   7   8   9   10   11   12   13   14   15   16   17   18   19   20   21   22   23   24   25   26  
SpanSpan  
(m)(m)   TOP/LOWER:
Consult Modulift
for Shackle sizes

Weight per Set (kgs)

* Weight based on heaviest spreader in series using configuration recommended in user instructions
WEIGHT MOD 6 MOD 12 MOD 24 MOD 34 MOD 50 MOD MOD MOD MOD MOD MOD
70/70H 110/110H 110SH 250 400 600
Max Component Weight 8.1 19 41 51 140 240 367 444 860 1365 2665
Min Component Weight 0.6 1.3 5 7 11 17/32 44/55 63 90 135 135
Weight at Max Span 32 75 178 290 532 972/1090 1970/2130 2628 4895 8260 17260

Email:
Email:[email protected]
[email protected] www.modulift.com
www.modulift.com 7
 Regulations, Standards & Compliance

Each Modulift Spreader Beam series has been proven by being Proof Load Tested in the Modulift compression test rig and all
products comply with the relevant standards as detailed below:

UK & Europe Compliance

All our Spreader Beams have been designed in accordance with:
• BS EN 13155: 2003+A2:2009: Cranes – Safety – Non-­fixed load lifting attachments
• DNV Standard for Certification No. 2.22 Lifting Appliances 2011
• Mod 6 up to Mod 800/1000 Type Approved by DNV
• LOLER: 1998 (Lifting Operations and Lifting Equipment Regulations)
• PUWER: 1998 (Provision and Use of Work Equipment Regulations)
• EC Machinery Directive 2006/42/EC
• BS EN 1993-1: 2005: Eurocode 3 We now have all our
USA Compliance Spreader Beams up to
•
•
ASME B30.20 - 2010: For Below-the-Hook Lifting Devices.
ASME BTH-1 2011: Design of Below-the-Hook Lifting Devices.
1000t capacity
DNV Type Approved.
Australia Compliance
• AS 4991 - 2004: Lifting Devices.

DNV Standard for Certification

DNV 2.22: Modulift Spreader Beams designs conform to DNV Standard for Certification No.2.22 Lifting Appliances.
Modulift is the first and only Spreader Beam Manufacturer in the world to have the globally recognised DNV Type Approval
for all Spreader Beams up to 1000t capacity in accordance with DNV’s standard for Certification No. 2.22 for Lifting Appliances
2011, at no extra cost to the client.

For those customers who require a higher level of quality standard, Modulift also provides further options for project specific
3rd party verification.

When a project demands the highest level of certification Modulift are able to offer our customers varying degrees of
additional DNV certification depending upon their individual QA requirements, including:
• Proof Load Test Survey Report and Record of Test
• DNV Certificate of Conformity for Manufacture & Test
(CG3 in accordance with ILO convention 152)
Please ask about these additional services at the time of
 

your enquiry.

Ask Modulift about the Level of Options Available to Ensure Your Safe Lift

Level 1. Standard Modulift Spreader Beams

In accordance with BS EN 13155 - 2003. Available CE Marked and supplied with a Certificate of Conformity, up to
400t available off-the-shelf.

Level 2. Individual Proof Load Testing of Modulift Spreader Beams

Modulift offer an individual Proof Load Test service with or without 3rd party verification to those requiring a
higher level of certification. Please ask for further information.

Level 3. Modulift Spreader Beams with project specific DNV Certification

Although our range Spreader Beams are now DNV Type Approved, we can also offer project specific DNV
certification of individual Spreader Beams.
It is the ultimate in certification and quality control for the most demanding project specification; a Modulift
Spreader Beam individually certified by DNV in terms of design, manufacturing and Proof Load testing. Supplied
with a design review report and Certificate of Conformity for Manufacture and Test, issued by DNV.

8 Email: [email protected] www.modulift.com

 Enhanced QA Options/Custom Design Solutions

Modulift recognise the high level QA requirements of the Oil & Gas, Offshore and Renewable Energy industries. In
response to these high standards Modulift offer Enhanced QA Options to our standard Off-the-Shelf range of Spreader
Beams - see our options list below.

Product Off-the-Shelf Enhanced

Specification QA Options
BS EN 13155 - 2003,
BS EN 1993-1 - 1- 2005
Design ASME B30.20 - 2010,
Project Specific requirements
AS 4991 - 2004, DNV 2.22

Impact tested to -20° C /-4°F in accordance Impact tested to -40° C /-40°F in accordance with
Materials with BS EN10025/10210/10219 BS EN 10025/10225/API SL

Welding BS EN ISO 15614.1

MOD 1600 Standard Finish - Yellow RAL 1003 High build systems suitable for marine
Paint Finish 2 Pack epoxy paint system environments

Markings Engraved stainless steel ID plate ID plate and additional labelling

Testing - Proof Load Testing & NDT

Bolts Grade 8.8 HT zinc plated Low temperature, galvanised

Shackles Rated to -20° C /-4°F Rated to -40° C /-40°F

Slings Rated to -40° C/ -40°F and BS EN 13414 -1 & -3 compliant

Verification Off-the-Shelf Enhanced

MOD 1000 QA Options
DNV Type Approval √ √

DNV Design Approval √ √

Original Design Verification Proof Load Test √ √

Job specific Proof Load Testing & NDT on individual beams x √

MOD 600
Third Party Verification of individual beams x √

Certification / Documentation Off-the-Shelf Enhanced

MOD 400
QA Options
MOD 1000
EC Declaration of Conformity √ √

User Instructions √ √

Material Certification x √

Inspection and Test Plan (ITP) x √

Welding, NDT &MOD

Proof600
Load Testing documentation x √

MRB (Manufactures Record Book) x √

Email: [email protected] www.modulift.com 9

 Accessories

SHACKLES & SLINGS

Modulift can supply shackle sets and slings to suit all rigging
requirements. Sling Types: Round Slings, Chain Slings, Flat
Webbing Slings, Wire Rope Slings and Cable Laid Slings &
Grommets to BS EN 13414-1 & 3.
Shackles generally conform to EN 13889 and US Fed Spec
RR-C-271.

Summary of the sizes of Shackles that are required for the Modulift Modular
Spreader Beam Range:

Modulift Spreader Bottom Top Shackle Van Beest Model The Crosby Group
Series Shackle Size Size Number Model Number

MOD 6 3.25t 4.75t G - 4163 G - 2130

MOD 12 6.5t 8.5t G - 4163 G - 2130

MOD 24 12t 17t G - 4163 G - 2130

MOD 34 17t 25t G - 4163 G - 2130

MOD 50 25t 35t G - 4163 G - 2130

MOD 70 35t 55t G - 4163 G - 2130

MOD 70H 55t 85t G - 4163 G - 2130

MOD 110 55t 85t G - 4163 G - 2130

MOD 110H 85t 120t G - 163/P-6036 G - 2130

MOD 110SH 120t 150t P - 6036

MOD 250 125t-200t 200t-300t P - 6033

MOD 400 200t-400t 300t-400t P - 6033

MOD 600 200t-500t 300t-600t P - 6033

All Modulift shackles recommended are

DNV Type Approved.

10 Email: [email protected] www.modulift.com

 Accessories

LOGISTIC CRADLES
Modulift Logistic Cradles are an essential part of safe and
efficient handling and storage of Modulift Systems.
Designed with a storage position for each component, the
cradles enable instant recognition of any missing
components.
Cradles can be produced to suit any rig combination. Other
design features can include fork pockets, stacking feet, lift-
ing points, tool storage and security cases for locking.

DROP LINK ACCESSORIES -

DELTA PLATES AND CLEVIS DROP LINKS
A range of alternatives to standard Drop Links are available to
help you with your rigging needs.
Clevis Drop Links will rotate the shackle orientation by 90
degrees. Delta Plates enable 2 slings to be
connected with separate shackles.

DROP LINK ASSEMBLY AIDS

The Modulift Drop Link Assembly Aids are a tool used when rigging
drop links into heavier Spreader Beams. It enables the drop link to be
supported and aligned in position while a shackle is being fitted. Drop
Link Assembly Aids are available for the MOD 250 and larger sizes
(must be asked for at time of ordering).

STEP DOWN END UNITS AND

CONE ADAPTORS
For requirements with longer spans and lighter loads,
these enable a Spreader System to be optimised
to suit a particular need. Step Down End Units are
designed for smaller sizes up to MOD 70.
Cone Adaptors are used for the larger sizes.

FASTENERS
Modulift bolts, nuts and washers are specifically
supplied for each Spreader Beam assembly; see
individual User Instructions in the following pages for
details.
Additional fasteners that are Modulift approved can be
purchased at any time.

Email: [email protected] www.modulift.com 11

 Engineering Design and Lift Management

Custom lifting solutions; innovative, approved safety, effective, on budget and on time

With over 20 years of specialist lifting experience, Modulift is expert in designing and manufacturing any manner of
complicated or excessively heavy lifting project. At the forefront of every lift, Modulift maintains the very highest standards of
risk management while ensuring a safe lifting environment.

With a team of highly trained specialist in-house Lifting Engineers, Project Consultants, Rig Planning Services and On-Site
Support, Modulift can deliver an extensive personalised package which will guide you through from your initial enquiry up to
the day of your successful lift.

Using amongst the most Quality Assured products in the lifting industry, Modulift can design and build to the very highest
global standards. Enhanced with a custom integrated service, Modulift can ensure a safe, cost efficient lift on time, every time.

Lifting solutions made easy

1. Simple Single Beam 2 point Lift

A single Spreader Beam is the simplest configuration and
is suitable for 2 point lifts. The Spreader Beam absorbs the
compression forces to protect the load being lifted.

2. Single Beam 4 Point Lift

This configuration again used a single beam where the load being
lifted has four individual lifting points.

3. 1-Over-2 Rig
We use this configuration when vertical slings are essential for
4 point lifts. By varying the sling lengths, we can also take into
account an offset center of gravity.

4. 1-Over-2 Inline Rig

Ideal for those lifts where the span is long and potential bending
of the load is a problem. Further cascading layers are available to
increase the number of lifting points

12 Email: [email protected] www.modulift.com

 Engineering Design and Lift Management

5. 1-Over-1
Where there are an uneven number of points to lift from a 1
over 1 system can be used to lift the load whilst still providing a
balanced rig.

6. Various Multi Spreader Beam Rigs

With our expert help we can address most lifting issues using
a combination of our products to fit the application and the
circumstances.

7. CMOD Spreader Frame

The CMod spreader frame uses corner units to connect existing
Modulift struts into a 4 point modular spreader frame. This uses
less headroom than a 1 over 2 rig.

8. Lifting Frame (H Frame)

For extremely low headroom applications, Modulift can design and
fabricate a bespoke lifting frame to suit your exact requirements

Using these Rig Design options, Modulift can provide purpose-built lifting equipment which takes in to account all the
necessary elements such as load type and weight, height restrictions, environmental factors, Centre of Gravity composition for
example, to deploy a safe and strategic lift. Modulift team members are available and on-hand every step of the way, assisting
in producing an effective and smooth-running project.

Email: [email protected] www.modulift.com 13

 Engineering Design and Lift Management

Modulift Custom Process Flow

Call today to discuss

your Custom Designed &
Managed Lifting Project
Tel: +44 (0) 1202 621511

14 Email: [email protected] www.modulift.com

 QuickJoint 2

What is a QuickJoint? - “It’s Features:

only the future” says Modulift • Fast assembly due to QJ2 design QuickJoint 2 -
The QuickJoint 2 (QJ2) is the smaller
• Lightweight: Less than 8kg The future of
• Handy carry case enables the QJ2 to be
addition to the Modulift Spreader System.
QuickJoint has a similar arrangement to easily moved to a worksite before portable beams
assembly
the standard Modulift Spreader System 1. You Wanted Fast Assembly
and retains all the flexibility with the We wanted to give you a
improved ability to be assembled quickly. BENEFITS:
Spreader System that is quick
• QJ2’s light weight aids compliance with and simple to assemble and
QJ2: WLL 2 Tonnes to 1.2m Manual Handling Regulations and PUWER so our team came up with
• Rapid assembly the QuickJoint Design!

The compact size and lightness of the 2. Strong But Lightweight

QuickJoint brings a new reality that The entire set of components
Spreader Beams don’t have to be bulky weighs less than 8 kgs for true
and difficult to take to site. The convenient portability and great durability
carry case will ensure that QuickJoint is easy
3. Handy Carry Case
to store, transport and used in applications
such as in machinery assembly, installation Our carry case enables the
and maintenance. QuickJoint to be easily moved
to a worksite before assembly.
Applications:
4. Multiple Applications
• Mechanical and Machinery Installation
QJ2 can be used for a variety
• Mechanical and Machinery Maintenance
of applications, including
• Aerospace Maintenance installation, maintenance,
TYPICAL QUICKJOINT ASSEMBLY
• Ship’s Machinery Maintenance aerospace and process
• Process Equipment Maintenance equipment maintenance.

QUICK RELEASE PIN:

Load v Span
45° STV Recommended 30° STV
Min.Top Configuration. Min.Top
Span/ SWL EU - End Unit (0.15m) Span SWL
Sling Length Sling Length
m /t /m /t
/m /m
300 2 0.25 EU EU 300 2 0.3
400 2 0.28 EU 100 EU 400 2 0.4
500 2 0.36 EU 200 EU 500 2 0.5
600 2 0.43 EU 300 EU 600 2 0.6
700 2 0.50 EU 300 100 EU 700 2 0.7
800 2 0.57 EU 300 200 EU 800 2 0.8
900 2 0.64 EU 300 300 EU 900 2 0.9
1000 2 0.71 EU 300 300 100 EU 1000 2 1.0
1100 2 0.78 EU 300 300 200 EU 1100 2 1.1
1200 2 0.85 EU 100 300 300 200 EU 1200 2 1.2

Email: [email protected] www.modulift.com 15

 MOD 6

The MOD 6 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 6 has an assembled span ranging from 400mm to 2.5m
which can be achieved in 100mm increments.

Component list β =’Sling to Vertical’ angle

Part ref: Description P3 - P7 P8
P1 END UNIT
b
P2 DROP LINK
P3 1m STRUT
P10
P4 0.6m STRUT P9 P1
Span P2
P5 0.3m STRUT
P6 0.2m STRUT Fig. 1: Typical Spreader Assembly.
P7 0.1m STRUT
P8 4.75t SHACKLE
Larger shackle
P9 3.25t SHACKLE
P10 M10X30, GRADE 8.8, HT BOLTS,
NUTS & WASHERS
END UNIT Smaller shackle
STRUT DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Top Min EU - End Unit (0.2m)
ISA
Span SWL Min Top Mod 6 - SYSTEM Specification
/m /t Sling /m /t Sling
Length / m
STV = ‘SLING TO STV

Length / m
• Rated at 6 tonnes SWL at 2.5m span
VERTICAL’ ANGLE, ß BSA

400 6 0.3 EU EU 400 6 0.4

• ‘Sling to vertical’ angle , ß, 45 degrees
or less
500 6 0.4 EU 100 EU 500 6 0.5
600 6 0.5 EU 200 EU 600 6 0.6 • End units and drop links are rated at
700 6 0.5 EU 300 EU 700 6 0.7 3 tonnes (6 tonnes combined
800 6 0.6 EU 300 100 EU 800 6 0.8
capacity)
900 6 0.7 EU 300 200 EU 900 6 0.9 • Bolt tightening torque: 60Nm
1000 6 0.7 EU 600 EU 1000 6 1.0 Spanner size required: 17mm
1100 6 0.8 EU 600 100 EU 1100 6 1.1
1200 6 0.9 EU 600 200 EU 1200 6 1.2
1300 6 0.9 EU 600 300 EU 1300 6 1.3
1400 6 1.0 EU 1000 EU 1400 6 1.4
1500 6 1.1 EU 1000 100 EU 1500 6 1.5
1600 6 1.2 EU 1000 200 EU 1600 6 1.6
1700 6 1.2 EU 1000 300 EU 1700 6 1.7
1800 6 1.3 EU 1000 300 100 EU 1800 6 1.8
1900 6 1.4 EU 1000 300 200 EU 1900 6 1.9
2000 6 1.5 EU 1000 600 EU 2000 6 2.0
2100 6 1.5 EU 600 1000 100 EU 2100 6 2.1
2200 6 1.6 EU 600 1000 200 EU 2200 6 2.2
2300 6 1.6 EU 600 1000 300 EU 2300 6 2.3
2400 6 1.7 EU 600 1000 300 100 EU 2400 6 2.4
2500 6 1.8 EU 600 1000 300 200 EU 2500 6 2.5

16 Email: [email protected] www.modulift.com

 MOD 12

The MOD 12 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 12 has an assembled span ranging from 0.5m to 4m which
can be achieved in 0.25m increments.

Component list β =’Sling to Vertical’ angle

Part ref: Description P8

b P3 - P7
P1 END UNIT
P2 DROP LINK
P3 1.5m STRUT P10
P4 1m STRUT P9 P1
Span P2
P5 0.75m STRUT
Fig. 1: Typical Spreader Assembly.
P6 0.5m STRUT
P7 0.25m STRUT
P8 8.5t SHACKLE Larger shackle

P9 6.5t SHACKLE
P10 M12X35, GRADE 8.8, HT BOLTS, END UNIT Smaller shackle
NUTS & WASHERS STRUT DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min TOP EU - End Unit (0.25m)
ISA
Span SWL Min TOP Mod 12 - SYSTEM Specification
/m /t Sling /m /t Sling
Length / m
STV = ‘SLING TO STV

Length / m
• Rated at 12 tonnes SWL at 4m span
VERTICAL’ ANGLE, ß BSA

0.5 12 0.4 EU EU 0.5 12 0.5 • ‘Sling to verticle’ angle, ß, 45 degrees

or less
0.75 12 0.6 EU 0.25 EU 0.75 12 0.75
1 12 0.8 EU 0.5 EU 1 12 1.0 • End units and drop links are rated at
1.25 12 0.9 EU 0.75 EU 1.25 12 1.25 6 tonnes (12 tonnes combined
capacity)
1.5 12 1.1 EU 1 EU 1.5 12 1.5
1.75 12 1.2 EU 1 0.25 EU 1.75 12 1.75 • Bolt tightening torque: 90 Nm
2 12 1.5 EU 1.5 EU 2 12 2 Spanner size required: 19mm
2.25 12 1.6 EU 1.5 0.25 EU 2.25 12 2.25
2.5 12 1.8 EU 1.5 0.5 EU 2.5 12 2.75
2.75 12 2.0 EU 1.5 0.75 EU 2.75 12 2.75
3 12 2.2 EU 1.5 1 EU 3 12 3
3.25 11 2.3 EU 1 1.5 0.25 EU 3.25 12 3.25
3.5 10 2.5 EU 1 1.5 0.5 EU 3.5 12 3.5
3.75 8 2.7 EU 1 1.5 0.75 EU 3.75 12 3.75
4 7 2.9 EU 1 1.5 0.75 0.25 EU 4 12 4.0

Email: [email protected] www.modulift.com 17

 MOD 24

The MOD 24 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 24 has an assembled span ranging from 1m to 6m which
can be achieved in 0.5m increments.

Component list β =’Sling to Vertical’ angle

P6
P3 - P5
Part ref: Description b
P1 END UNIT
P2 DROP LINK
P3 2m STRUT P1 P8 P2
P7
P4 1m STRUT
Span
P5 0.5m STRUT
Fig. 1: Typical Spreader Assembly.
P6 17t SHACKLE
P7 12t SHACKLE
P8 M20X50 GRADE 8.8 HT BOLTS, Larger shackle

NUTS & WASHERS

END UNIT Smaller shackle

STRUT DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Span SWL Min Top
Configuration
EU - End Unit (0.5m)
ISA

Span SWL Min Top

Mod 24 - SYSTEM Specification
/m /t Sling STV = ‘SLING TO STV /m /t Sling • Rated at 24 tonnes SWL at 3m span
Length / m VERTICAL’ ANGLE, ß Length / m
BSA

1 24 0.7 EU EU 1 24 1.0 • ‘Sling to Vertical’ ß , 45 degrees or

less
1.5 24 1.1 EU 0.5 EU 1.5 24 1.5
2 24 1.5 EU 1 EU 2 24 2.0 • End units and drop links are rated at
2.5 24 1.8 EU 1 0.5 EU 2.5 24 2.5
12 tonnes (24 tonnes combined
capacity)
3 24 2.2 EU 2 EU 3 24 3.0
3.5 22 2.5 EU 2 0.5 EU 3.5 24 3.5 • Bolt tightening torque: 150Nm
Spanner size required: 30mm
4 18 2.9 EU 2 1 EU 4 24 4.0
4.5 15 3.2 EU 0.5 2 1 EU 4.5 24 4.5
5 12 3.6 EU 2 2 EU 5 21 5.0
5.5 10 3.9 EU 2 2 0.5 EU 5.5 17 5.5
6 8 4.3 EU 2 2 1 EU 6 14 6.0

18 Email: [email protected] www.modulift.com

 MOD 34

The MOD 34 Series is modular in length and each system consists of one pair of end units and drop links, with
intermediate struts that can be assembled to achieve different spans. The MOD 34 has an assembled span ranging from
1 m to 8 m which can be achieved in 0.5 m increments.

Component list β =’Sling to Vertical’ angle

P6
P3 - P5
Part ref: Description b
P1 END UNIT
P2 DROP LINK
P3 2m STRUT P1 P8 P2
P7
P4 1m STRUT
Span
P5 0.5m STRUT
Fig. 1: Typical Spreader Assembly.
P6 25t SHACKLE
P7 17t SHACKLE
Larger shackle
P8 M20X50, GRADE 8.8, HT BOLTS,
NUTS & WASHERS

END UNIT Smaller shackle

STRUT SUB-ASSY
DROP LINK

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (0.5m)
ISA
Span SWL Min Top Mod 34 - SYSTEM Specification
/m /t Sling STV = ‘SLING TO /m /t Sling
Length / m
STV

Length /m
• Rated at 34 tonnes SWL at 12’ span
VERTICAL’ ANGLE, ß BSA

1 34 0.7 EU EU 1 34 1.0 • Base to Sling Angle, a, 45 degrees or

1.5 34 1.1 EU 0.5 EU 1.5 34 1.5
less
2 34 1.5 EU 1 EU 2 34 2.0 • End units and drop links are rated at
2.5 34 1.8 EU 1 0.5 EU 2.5 34 2.5 17 tonnes (34 tonnes combined
3 34 2.2 EU 2 EU 3 34 3.0
capacity)
3.5 32 2.5 EU 2 0.5 EU 3.5 34 3.5 • Bolt tightening torque: 150Nm
4 29 2.9 EU 2 1 EU 4 34 4.0 Spanner size required: 30mm
4.5 25 3.2 EU 0.5 2 1 EU 4.5 34 4.5
5 21 3.6 EU 2 2 EU 5 34 5.0
5.5 18 3.9 EU 2 2 0.5 EU 5.5 31 5.5
6 15 4.3 EU 2 2 1 EU 6 26 6.0
6.5 13 4.6 EU 0.5 2 2 1 EU 6.5 22 6.5
7 11 5.0 EU 2 2 2 EU 7 19 7.0
7.5 9 5.3 EU 0.5 2 2 2 EU 7.5 16 7.5
8 8 5.7 EU 2 2 2 1 EU 8 14 8.0

Email: [email protected] www.modulift.com 19

 MOD 50

The MOD 50 Series is modular in length and each system consists of one pair of end units and drop links, with
intermediate struts that can be assembled to achieve different spans. The MOD 50 has an assembled span ranging from
1m to 11m which can be achieved in 0.5m increments.

Component list β =’Sling to Vertical’ angle

P7
P3 - P6
Part ref: Description b
P1 END UNIT
P2 DROP LINK
P3 4m STRUT P1 P9 P2
P4 2m STRUT P8
Span
P5 1m STRUT
P6 0.5m STRUT Fig. 1: Typical Spreader Assembly.
P7 35t SHACKLE
P8 25t SHACKLE Larger shackle

P9 M20X65 HT BOLTS, NUTS &

WASHERS
END UNIT Smaller shackle
STRUT
DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Span SWL Min Top
Configuration
ISA
Span SWL Min Top
Mod 50 - SYSTEM Specification
EU - End Unit (0.5m)
/m /t Sling STV = ‘SLING TO STV
/m /t Sling
Length / m VERTICAL’ ANGLE, ß BSA
Length / m • Rated at 50 tonnes SWL at 6m span
1 50 0.7 EU EU 1 50 1.0 • ‘Sling to Verticle’ angle, ß 45 degrees or less
1.5 50 1.1 EU 0.5 EU 1.5 50 1.5
• End units and drop links are rated at 25
2 50 1.5 EU 1 EU 2 50 2.0 tonnes
2.5 50 1.8 EU 1 0.5 EU 2.5 50 2.5
(50 tonnes combined capacity)
3 50 2.2 EU 2 EU 3 50 3.0
• Bolt tightening torque: 150Nm
3.5 50 2.5 EU 2 0.5 EU 3.5 50 3.5
Spanner size required: 30mm
4 50 2.9 EU 2 1 EU 4 50 4
4.5 50 3.2 EU 0.5 2 1 EU 4.5 50 4.5
5 50 3.6 EU 2 2 EU 5 50 5
5.5 50 3.9 EU 2 2 0.5 EU 5.5 50 5.5
6 50 4.3 EU 2 2 1 EU 6 50 6
6.5 42 4.6 EU 0.5 2 2 1 EU 6.5 50 6.5
7 35 5.0 EU 2 2 2 EU 7 50 7
7.5 29 5.3 EU 0.5 2 2 2 EU 7.5 50 7.5
8 25 5.7 EU 2 2 2 1 EU 8 43 8
8.5 22 6.0 EU 0.5 1 4 2 EU 8.5 38 8.5
9 19 6.4 EU 4 4 EU 9 33 9
9.5 17 6.8 EU 4 4 0.5 EU 9.5 29 9.5
10 15 7.1 EU 4 4 1 EU 10 26 10
10.5 13 7.5 EU 1 4 4 0.5 EU 10.5 22 10.5
11 11 7.8 EU 2 4 4 EU 11 19 11

20 Email: [email protected] www.modulift.com

 MOD 50/24: Step-Downs

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 50/24 has an assembled span
ranging from 1 metre to 11 metres in 0.5 metre increments.

ß =’Sling to Vertical’ angle P7

P3 - P5
b

P1
P8 P9 P2
Span
Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT Smaller shackle

STEP DOWN STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top
EU - End Unit (0.5m)
ISA
P1 END UNIT (STEP DOWN)
/m /t sling /m /t sling
Length / m STV = ‘SLING TO STV

BSA Length / m P2 DROP LINK (MOD 24)

VERTICAL’ ANGLE, ß
P3 4.0m STRUT
1 24 0.7 EU EU 1 24 1
P4 2.0m STRUT
1.5 24 1.1 EU 0.5 EU 1.5 24 1.5
P5 1.0m STRUT
2 24 1.5 EU 1 EU 2 24 2
P6 0.5m STRUT
2.5 24 1.8 EU 1 0.5 EU 2.5 24 2.5
P7 17t SHACKLE
3 24 2.2 EU 2 EU 3 24 3
P8 12t SHACKLE
3.5 24 2.5 EU 2 0.5 EU 3.5 24 3.5
4 24 2.9 EU 2 1 EU 4 24 4
P9 M20x65 HT BOLTS,
NUTS & WASHERS
4.5 24 3.2 EU 0.5 2 1 EU 4.5 24 4.5
5 24 3.6 EU 4 EU 5 24 5
5.5 24 3.9 EU 4 0.5 EU 5.5 24 5.5
6 24 4.3 EU 4 1 EU 6 24 6 Mod 50/24 - SYSTEM Specification
6.5 24 4.6 EU 0.5 4 1 EU 6.5 24 6.5 • Rated at 24 tonnes SWL at 8m
7 24 5.0 EU 4 2 EU 7 24 7 span
7.5 24 5.3 EU 0.5 4 2 EU 7.5 24 7.5 • ‘Sling to Vertical’ angle, ß, 45 degrees
8 24 5.7 EU 1 4 2 EU 8 24 8 or less
8.5 22 6.0 EU 0.5 1 4 2 EU 8.5 24 8.5 • End units and drop links are rated at
9 19 6.4 EU 4 4 EU 9 24 9 12 tonnes (24 tonnes combined
9.5 17 6.8 EU 4 4 0.5 EU 9.5 24 9.5 capacity)
10 15 7.1 EU 4 4 1 EU 10 24 10 • Bolt tightening torque: 150Nm
10.5 13 7.5 EU 1 4 4 0.5 EU 10.5 22 10.5 Spanner size required: 30mm
11 11 7.8 EU 2 4 4 EU 11 19 11

Email: [email protected] www.modulift.com 21

 MOD 50/12: Step-Downs

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 50/12 has an assembled span
ranging from 1 metre to 11 metres in 0.5 metre increments.

ß =’Sling to Vertical’ angle P7

P3 - P5
b

P1
P8 P9 P2
Span
Fig.1: Typical Spreader Assembly.

Larger shackle

Smaller shackle
END UNIT
STEP DOWN STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV
Part ref: Description
Span SWL Min Top Configuration. ISA Span SWL Min Top
/m /t sling EU - End Unit (0.5m) /m /t sling P1 END UNIT (STEP DOWN)
Length / m STV = ‘SLING TO STV
Length / m
VERTICAL’ ANGLE, ß
BSA
P2 DROP LINK (MOD 12)
1 12 0.7 EU EU 1 12 1 P3 4.0m STRUT
1.5 12 1.1 EU 0.5 EU 1.5 12 1.5 P4 2.0m STRUT
2 12 1.5 EU 1 EU 2 12 2 P5 1.0m STRUT
2.5 12 1.8 EU 1 0.5 EU 2.5 12 2.5 P6 0.5m STRUT
3 12 2.2 EU 2 EU 3 12 3 P7 8.5t SHACKLE
3.5 12 2.5 EU 2 0.5 EU 3.5 12 3.5 P8 6.5t SHACKLE
4 12 2.9 EU 2 1 EU 4 12 4 P9 M20x65 HT BOLTS,
4.5 12 3.2 EU 0.5 2 1 EU 4.5 12 4.5 NUTS & WASHERS
5 12 3.6 EU 4 EU 5 12 5
5.5 12 3.9 EU 4 0.5 EU 5.5 12 5.5
6 12 4.3 EU 4 1 EU 6 12 6 Mod 50/12 - SYSTEM Specification
6.5 12 4.6 EU 0.5 4 1 EU 6.5 12 6.5 • Rated at 12 tonnes SWL at 10.5m
7 12 5.0 EU 4 2 EU 7 12 7 span
7.5 12 5.3 EU 0.5 4 2 EU 7.5 12 7.5 • ‘Sling to Vertical’ angle, ß, 45 degrees
8 12 5.7 EU 1 4 2 EU 8 12 8 or less
8.5 12 6.0 EU 0.5 1 4 2 EU 8.5 12 8.5
• End units and drop links are rated at
9 12 6.4 EU 4 4 EU 9 12 9
6 tonnes (12 tonnes combined
9.5 12 6.8 EU 4 4 0.5 EU 9.5 12 9.5 capacity)
10 12 7.1 EU 4 4 1 EU 10 12 10
• Bolt tightening torque: 150Nm
10.5 12 7.5 EU 1 4 4 0.5 EU 10.5 12 10.5
Spanner size required: 30mm
11 11 7.8 EU 2 4 4 EU 11 12 11

22 Email: [email protected] www.modulift.com

 MOD 50/6: Step-Downs

The MOD 6 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 50/6 has an assembled span ranging from 1m to 11m which
can be achieved in 0.5m increments.

ß =’Sling to Vertical’ angle

P3 - P5 P7
b

P1
P8 P9 P2
Span
Fig.1: Typical Spreader Assembly.

Larger shackle

Smaller shackle
END UNIT
STEP DOWN STRUT DROP LINK SUB-ASSY

Load v Span Component list

45˚ STV Recommended Sling Angle Format
30˚ STV Part ref: Description
Configuration
Span SWL Top Min EU - End Unit (0.2m)
ISA
Span SWL Min Top P1 END UNIT (STEP DOWN)
/m /t Sling STV = ‘SLING TO STV
/m /t Sling
Length / m VERTICAL’ ANGLE, ß BSA Length / m P2 DROP LINK

1 6 0.7 EU EU 1 6 1 P3 4.0m STRUT

1.5 6 1.1 EU 0.5 EU 1.5 6 1.5 P4 2.0m STRUT

2 6 1.5 EU 1 EU 2 6 2 P5 1.0m STRUT
2.5 6 1.8 EU 1 0.5 EU 2.5 6 2.5 P6 0.5m STRUT
3 6 2.2 EU 2 EU 3 6 3 P7 4.75t SHACKLE
3.5 6 2.5 EU 2 0.5 EU 3.5 6 3.5 P8 3.25t SHACKLE
4 6 2.9 EU 2 1 EU 4 6 4 P9 M20x65 HT BOLTS,
4.5 6 3.2 EU 0.5 2 1 EU 4.5 6 4.5 NUTS & WASHERS
5 6 3.6 EU 4 EU 5 6 5
5.5 6 3.9 EU 4 0.5 EU 5.5 6 5.5
6 6 4.3 EU 4 1 EU 6 6 6 Mod 6 - SYSTEM Specification
6.5 6 4.6 EU 0.5 4 1 EU 6.5 6 6.5 • Rated at 6 tonnes SWL at 11m span
7 6 5.0 EU 4 2 EU 7 6 7
• ‘Sling to vertical’ angle , ß, 45 degrees
7.5 6 5.3 EU 0.5 4 2 EU 7.5 6 7.5 or less
8 6 5.7 EU 1 4 2 EU 8 6 8
• End units and drop links are rated at
8.5 6 6.0 EU 0.5 1 4 2 EU 8.5 6 8.5
3 tonnes (6 tonnes combined
9 6 6.4 EU 4 4 EU 9 6 9
capacity)
9.5 6 6.8 EU 4 4 0.5 EU 9.5 6 9.5
• Bolt tightening torque: 150Nm
10 6 7.1 EU 4 4 1 EU 10 6 10
Spanner size required: 30mm
10.5 6 7.5 EU 1 4 4 0.5 EU 10.5 6 10.5
11 6 7.8 EU 2 4 4 EU 11 6 11

Email: [email protected] www.modulift.com 23

 MOD 70

The MOD 70 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 70 has an assembled span ranging from 1m to 12m which
can be achieved in 0.5m increments.

Component list β =’Sling to Vertical’ angle P7

P3 - P6
Part ref: Description b
P1 END UNIT
P2 DROP LINK
P3 4m STRUT P1 P9 P2
P4 2m STRUT P8
Fig.1: TypicalSpan
Spreader Assembly.
P5 1m TRUT
P6 0.5m STRUT Fig. 1: Typical Spreader Assembly.
P7 55t SHACKLE
P8 35t SHACKLE Larger shackle

P9 M20X65, GRADE 8.8 HT BOLTS,

NUTS & WASHERS
END UNIT Smaller shackle
STRUT
DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Span SWL Min Top
Configuration ISA
Span SWL Min Top
Mod 70 - SYSTEM Specification
EU - End Unit (0.5m)
/m /t Sling STV = ‘SLING TO STV /m /t Sling • Rated at 70 tonnes SWL at 7m span
Length /m VERTICAL’ ANGLE, ß
BSA
Length / m

1 70 0.7 EU EU 1 70 1
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
1.5 70 1.1 EU 0.5 EU 1.5 70 1.5
2 70 1.5 EU 1 EU 2 70 2 • End units and drop links are rated at
2.5 70 1.8 EU 1 0.5 EU 2.5 70 2.5 35 tonnes (70 tonnes combined
capacity)
3 70 2.2 EU 2 EU 3 70 3
3.5 70 2.5 EU 2 0.5 EU 3.5 70 3.5 • Bolt tightening torque: 150Nm
4 70 2.9 EU 2 1 EU 4 70 4 Spanner size required: 30mm
4.5 70 3.2 EU 0.5 2 1 EU 4.5 70 4.5
5 70 3.6 EU 4 EU 5 70 5
5.5 70 3.9 EU 4 0.5 EU 5.5 70 5.5
6 70 4.3 EU 4 1 EU 6 70 6
6.5 70 4.6 EU 0.5 4 1 EU 6.5 70 6.5
7 70 5.0 EU 4 2 EU 7 70 7
7.5 67 5.3 EU 0.5 4 2 EU 7.5 70 7.5
8 58 5.7 EU 1 4 2 EU 8 70 8
8.5 51 6.0 EU 0.5 1 4 2 EU 8.5 70 8.5
9 44 6.4 EU 4 4 EU 9 70 9
9.5 39 6.8 EU 4 4 0.5 EU 9.5 68 9.5
10 34 7.1 EU 4 4 1 EU 10 59 10
10.5 30 7.5 EU 1 4 4 0.5 EU 10.5 53 10.5
11 27 7.8 EU 2 4 4 EU 11 47 11
11.5 25 8.2 EU 2 4 4 0.5 EU 11.5 43 11.5
12 22 8.5 EU 2 4 4 1 EU 12 38 12

24 Email: [email protected] www.modulift.com

 MOD 70H

The MOD 70H Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 70H has an assembled span ranging from 1m to 12m which
can be achieved in 0.5m increments.

Component list β =’Sling to Vertical’ angle P7

P3 - P6
Part ref: Description b
P1 END UNIT
P2 DROP LINK
P3 4m STRUT P1 P9 P2
P4 2m STRUT P8
Span Assembly.
Fig.1: Typical Spreader
P5 1m STRUT
P6 0.5m STRUT Fig. 1: Typical Spreader Assembly.
P7 85t SHACKLE
Larger shackle
P8 55t SHACKLE
P9 M20X65, GRADE 8.8 HT BOLTS,
NUTS & WASHERS
END UNIT Smaller shackle
STRUT
DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Span SWL Min Top
Configuration ISA
Span SWL Min Top Mod 70H - SYSTEM Specification
EU - End Unit (0.5m)
/m /t Sling /m /t Sling
Length /m
STV = ‘SLING TO STV

Length / m
• Rated at 100 tonnes SWL at 6m span
VERTICAL ANGLE, ß BSA

• Sling to Vertical’ angle, ß, 45 degrees

1 100 0.7 EU EU 1 100 1
or less
1.5 100 1.1 EU 0.5 EU 1.5 100 1.5
2 100 1.5 EU 1 EU 2 100 2 • End units and drop links are rated at
2.5 100 1.8 EU 1 0.5 EU 2.5 100 2.5
50 tonnes (100 tonnes combined
capacity)
3 100 2.2 EU 2 EU 3 100 3
3.5 100 2.5 EU 2 0.5 EU 3.5 100 3.5 • Bolt tightening torque: 150Nm
4 100 2.9 EU 2 1 EU 4 100 4 Spanner size required: 30mm
4.5 100 3.2 EU 0.5 2 1 EU 4.5 100 4.5
5 100 3.6 EU 2 2 EU 5 100 5
5.5 100 3.9 EU 2 2 0.5 EU 5.5 100 5.5
6 100 4.3 EU 2 2 1 EU 6 100 6
6.5 88 4.6 EU 0.5 2 2 1 EU 6.5 100 6.5
7 76 5.0 EU 2 2 2 EU 7 100 7
7.5 67 5.3 EU 0.5 2 2 2 EU 7.5 100 7.5
8 58 5.7 EU 2 2 2 1 EU 8 100 8
8.5 51 6.0 EU 0.5 1 4 2 EU 8.5 89 8.5
9 44 6.4 EU 4 4 EU 9 77 9
9.5 39 6.8 EU 4 4 0.5 EU 9.5 68 9.5
10 34 7.1 EU 4 4 1 EU 10 59 10
10.5 30 7.5 EU 1 4 4 0.5 EU 10.5 53 10.5
11 27 7.8 EU 2 4 4 EU 11 47 11
11.5 25 8.2 EU 2 4 4 0.5 EU 11.5 43 11.5
12 22 8.5 EU 2 4 4 1 EU 12 38 12

Email: [email protected] www.modulift.com 25

 MOD 70/34: Step-Downs

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 70/34 has an assembled span
ranging from 1 metre to 12 metres in 0.5 metre increments.

ß =’Sling to Vertical’ angle

P7
P3 - P6
b

P1
P8 P9 P2
Span

Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT
STEP DOWN STRUT DROP LINK SUB-ASSY Smaller shackle

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top P1 END UNIT (STEP DOWN)
ISA

/m /t sling EU - End Unit (0.5m) /m /t sling

STV = ‘SLING TO
STV

Length / m BSA Length / m P2 DROP LINK (MOD 34)

VERTICAL’ ANGLE, ß
P3 4.0m STRUT
1 34 0.7 EU EU 1 34 1
1.5 34 1.1 EU 0.5 EU 1.5 34 1.5 P4 2.0m STRUT

2 34 1.5 EU 1 EU 2 34 2 P5 1.0m STRUT

2.5 34 1.8 EU 1 0.5 EU 2.5 34 2.5 P6 0.5m STRUT

3 34 2.2 EU 2 EU 3 34 3 P7 25t SHACKLE

3.5 34 2.5 EU 2 0.5 EU 3.5 34 3.5 P8 17t SHACKLE
4 34 2.9 EU 2 1 EU 4 34 4 P9 M20x65 HT BOLTS,
4.5 34 3.2 EU 0.5 2 1 EU 4.5 34 4.5 NUTS & WASHERS
5 34 3.6 EU 4 EU 5 34 5
5.5 34 3.9 EU 4 0.5 EU 5.5 34 5.5
6 34 4.3 EU 4 1 EU 6 34 6 Mod 70/34 - SYSTEM Specification
6.5 34 4.6 EU 0.5 4 1 EU 6.5 34 6.5 • Rated at 34 tonnes SWL at 10m
7 34 5.0 EU 4 2 EU 7 34 7 span
7.5 34 5.3 EU 0.5 4 2 EU 7.5 34 7.5 • ‘Sling to Vertical’ angle, ß, 45 degrees
8 34 5.7 EU 1 4 2 EU 8 34 8 or less
8.5 34 6.0 EU 0.5 1 4 2 EU 8.5 34 8.5 • End units and drop links are rated at
9 34 6.4 EU 4 4 EU 9 34 9 17 tonnes (34 tonnes combined
9.5 34 6.8 EU 4 4 0.5 EU 9.5 34 9.5 capacity)
10 34 7.1 EU 4 4 1 EU 10 34 10 • Bolt tightening torque: 150Nm
10.5 30 7.5 EU 1 4 4 0.5 EU 10.5 34 10.5 Spanner size required: 30mm
11 27 7.8 EU 2 4 4 EU 11 34 11
11.5 25 8.2 EU 2 4 4 0.5 EU 11.5 34 11.5
12 22 8.5 EU 2 4 4 1 EU 12 34 12

26 Email: [email protected] www.modulift.com

 MOD 70/24: Step-Downs

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 70/24 has an assembled span
ranging from 1 metre to 12 metres in 0.5 metre increments.

ß =’Sling to Vertical’ angle

P3 - P6 P7
b

P1
P8 P9 P2
Span

Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT Smaller shackle

STEP DOWN STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top P1 END UNIT (STEP DOWN)
ISA

/m /t sling EU - End Unit (0.5m) /m /t sling

Length / m STV = ‘SLING TO STV

BSA Length / m P2 DROP LINK (MOD 24)

VERTICAL’ ANGLE, ß
P3 4.0m STRUT
1 24 0.7 EU EU 1 24 1
P4 2.0m STRUT
1.5 24 1.1 EU 0.5 EU 1.5 24 1.5
2 24 1.5 EU 1 EU 2 24 2
P5 1.0m STRUT

2.5 24 1.8 EU 1 0.5 EU 2.5 24 2.5

P6 0.5m STRUT

3 24 2.2 EU 2 EU 3 24 3 P7 17t SHACKLE

3.5 24 2.5 EU 2 0.5 EU 3.5 24 3.5 P8 12t SHACKLE

4 24 2.9 EU 2 1 EU 4 24 4 P9 M20x65 HT BOLTS,

4.5 24 3.2 EU 0.5 2 1 EU 4.5 24 4.5
NUTS & WASHERS

5 24 3.6 EU 4 EU 5 24 5
5.5 24 3.9 EU 4 0.5 EU 5.5 24 5.5
6 24 4.3 EU 4 1 EU 6 24 6 Mod 70/34 - SYSTEM Specification
6.5 24 4.6 EU 0.5 4 1 EU 6.5 24 6.5 • Rated at 24 tonnes SWL at 11.5m
7 24 5.0 EU 4 2 EU 7 24 7 span
7.5 24 5.3 EU 0.5 4 2 EU 7.5 24 7.5 • ‘Sling to Vertical’ angle, ß, 45 degrees
8 24 5.7 EU 1 4 2 EU 8 24 8 or less
8.5 24 6.0 EU 0.5 1 4 2 EU 8.5 24 8.5 • End units and drop links are rated at
9 24 6.4 EU 4 4 EU 9 24 9 12 tonnes (24 tonnes combined
9.5 24 6.8 EU 4 4 0.5 EU 9.5 24 9.5 capacity)
10 24 7.1 EU 4 4 1 EU 10 24 10 • Bolt tightening torque: 150Nm
10.5 24 7.5 EU 1 4 4 0.5 EU 10.5 24 10.5 Spanner size required: 30mm
11 24 7.8 EU 2 4 4 EU 11 24 11
11.5 24 8.2 EU 2 4 4 0.5 EU 11.5 24 11.5
12 22 8.5 EU 2 4 4 1 EU 12 24 12

Email: [email protected] www.modulift.com 27

 MOD 110

The MOD 110 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 110 has an assembled span ranging from 2m to 16m which
can be achieved in 0.5m increments.

Component list β =’Sling to Vertical’ angle

P7
Part ref: Description P3 - P6
b
P1 END UNIT
P2 DROP LINK
P3 4m STRUT P1 P9 P2
P4 2m STRUT P8 Span
Fig.1: Typical Spreader Assembly.
P5 1m STRUT
Fig. 1: Typical Spreader Assembly.
P6 0.5 STRUT
P7 85t SHACKLE
Larger shackle
P8 55t SHACKLE

P9 M20X65 HT BOLTS, NUTS &

WASHERS
END UNIT Smaller shackle
STRUT DROP LINK SUB-ASSY
Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration Mod 110 - SYSTEM Specification
Span SWL Min Top Span SWL Min Top
ISA

EU - End Unit (1m)

/m /t sling STV = ‘SLING TO VERTICAL’ STV /m /t Sling • Rated at 110 tonnes SWL at 6m span.
Length / m ANGLE , ß Length / m
BSA

• ‘Sling to Vertical’ angle, ß, 45 degrees

2 110 1.5 EU EU 2 110 2 or less
2.5 110 1.8 EU 0.5 EU 2.5 110 2.5
• End units and drop links are rated at 55
3 110 2.2 EU 1 EU 3 110 3
tonnes 110 tonnes combined capacity)
3.5 110 2.5 EU 1 0.5 EU 3.5 110 3.5
• Bolt tightening torque: 150Nm
4 110 2.9 EU 2 EU 4 110 4
Spanner size required: 30mm
4.5 110 3.2 EU 2 0.5 EU 4.5 110 4.5
5 110 3.6 EU 2 1 EU 5 110 5
5.5 110 3.9 EU 0.5 2 1 EU 5.5 110 5.5
6 110 4.3 EU 2 2 EU 6 110 6
6.5 109 4.6 EU 2 2 0.5 EU 6.5 110 6.5
7 106 5.0 EU 2 2 1 EU 7 110 7
7.5 102 5.3 EU 0.5 2 2 1 EU 7.5 110 7.5
8 98 5.7 EU 2 2 2 EU 8 110 8
8.5 93 6.0 EU 0.5 2 2 2 EU 8.5 110 8.5
9 88 6.4 EU 2 2 2 1 EU 9 110 9
9.5 83 6.8 EU 0.5 1 4 2 EU 9.5 110 9.5
10 78 7.1 EU 4 4 EU 10 110 10
10.5 72 7.5 EU 4 4 0.5 EU 10.5 110 10.5
11 66 7.8 EU 4 4 1 EU 11 110 11
11.5 62 8.2 EU 0.5 4 4 1 EU 11.5 107 11.5
12 58 8.5 EU 2 4 4 EU 12 100 12
12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 92 12.5
13 48 9.5 EU 2 4 4 1 EU 13 84 13
13.5 45 9.75 EU 2 4 4 1 0.5 EU 13.5 80 13.5
14 43 10.0 EU 4 4 4 EU 14 75 14
14.5 39 10.25 EU 0.5 4 4 4 EU 14.5 69 14.5
15 35 10.5 EU 4 4 4 1 EU 15 62 15
15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5
16 31 11.5 EU 4 4 4 2 EU 16 53 16

28 Email: [email protected] www.modulift.com

 MOD 110H

The MOD 110H Series is modular in length and each system consists of one pair of end units and drop links, with intermediate
struts that can be assembled to achieve different spans. The MOD 110H has an assembled span ranging from 2m to 16m
which can be achieved in 0.5m increments.

Component list β =’Sling to Vertical’ angle

P7
Part ref: Description P3 - P6
b
P1 END UNIT
P2 DROP LINK
P3 4m STRUT P1 P9 P2
P4 2m STRUT P8 Span
Fig.1: Typical Spreader Assembly.
P5 1m STRUT
Fig. 1: Typical Spreader Assembly.
P6 0.5m STRUT
P7 120t SHACKLE Larger shackle
P8 85t SHACKLE
P9 M20X65 HT BOLTS, NUTS &
WASHERS Smaller shackle
END UNIT
STRUT
DROP LINK SUB-ASSY
Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 110H - SYSTEM Specification
/m /t Sling STV = ‘SLING TO /m /t Sling
Length/ m VERTICAL’ ANGLE, ß
STV

BSA
Length / m
• Rated at 170 tonnes SWL at 8m span

2 125 1.5 EU EU 2 170 2 • ‘Sling to Vertical’ angle, ß, 45 degrees

2.5 124 1.8 EU 0.5 EU 2.5 170 2.5
or less
3 124 2.2 EU 1 EU 3 170 3 • End units and drop links are rated at 85
3.5 123 2.5 EU 1 0.5 EU 3.5 170 3.5 tonnes (170 tons combined capacity)
4 122 2.9 EU 2 EU 4 170 4 • Bolt tightening torque: 150Nm
4.5 120 3.2 EU 2 0.5 EU 4.5 170 4.5 Spanner size required: 30mm
5 118 3.6 EU 2 1 EU 5 170 5
5.5 115 3.9 EU 0.5 2 1 EU 5.5 170 5.5
6 112 4.3 EU 2 2 EU 6 170 6
6.5 109 4.6 EU 2 2 0.5 EU 6.5 170 6.5
7 106 5.0 EU 2 2 1 EU 7 170 7
7.5 102 5.3 EU 0.5 2 2 1 EU 7.5 170 7.5
8 98 5.7 EU 2 2 2 EU 8 170 8
8.5 93 6.0 EU 0.5 2 2 2 EU 8.5 161 8.5
9 88 6.4 EU 2 2 2 1 EU 9 152 9
9.5 83 6.8 EU 0.5 1 4 2 EU 9.5 144 9.5
10 78 7.1 EU 4 4 EU 10 135 10
10.5 72 7.5 EU 4 4 0.5 EU 10.5 125 10.5
11 66 7.8 EU 4 4 1 EU 11 114 11
11.5 62 8.2 EU 0.5 4 4 1 EU 11.5 107 11.5
12 58 8.5 EU 2 4 4 EU 12 100 12
12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 92 12.5
13 48 9.5 EU 2 4 4 1 EU 13 84 13
13.5 45 9.75 EU 2 4 4 1 0.5 EU 13.5 80 13.5
14 43 10.0 EU 4 4 4 EU 14 75 14
14.5 39 10.25 EU 0.5 4 4 4 EU 14.5 69 14.5
15 35 10.5 EU 4 4 4 1 EU 15 62 15
15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5
16 31 11.5 EU 4 4 4 2 EU 16 53 16

Email: [email protected] www.modulift.com 29

 MOD 110SH

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 110SH has an
assembled span ranging from 2m to 16m in 0.5m increments.

Component list β =’Sling to Vertical’ angle

P7
P3 - P6
Part ref: Description b
P1 END UNIT
P2 DROP LINK
P3 4m STRUT P1 P9 P2
P8 Span
P4 2m STRUT Fig.1: Typical Spreader Assembly.
P5 1m STRUT Fig. 1: Typical Spreader Assembly.
P6 0.5m STRUT
Larger shackle
P7 150t SHACKLE
P8 120t SHACKLE
P9 M20X65 GRADE 8.8, HT BOLTS, Smaller shackle
NUTS & WASHERS END UNIT
STRUT DROP LINK SUB-ASSY

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 110SH - SYSTEM Specification
/m /t sling /m /t sling
STV = ‘SLING TO
• Rated at 240 tonnes SWL at 6m span
STV

Length/ m BSA Length/ m

VERTICAL’ ANGLE, ß
2 158 1.5 EU EU 2 240 2 • ‘Sling to Vertical’ angle, ß, 45 degrees
2.5 157 1.8 EU 0.5 EU 2.5 240 2.5 or less
3 156 2.2 EU 1 EU 3 240 3
3.5 154 2.5 EU 1 0.5 EU 3.5 240 3.5
• End units and drop links are rated at
4 152 2.9 EU 2 EU 4 240 4
120 tonnes (240 tonnes combined
capacity)
4.5 149 3.2 EU 2 0.5 EU 4.5 240 4.5
5 146 3.6 EU 2 1 EU 5 240 5 • Bolt tightening torque: 150Nm
5.5 143 3.9 EU 0.5 2 1 EU 5.5 240 5.5 Spanner size required: 30mm
6 140 4.3 EU 2 2 EU 6 240 6
6.5 136 4.6 EU 2 2 0.5 EU 6.5 234 6.5
7 132 5.0 EU 2 2 1 EU 7 228 7
7.5 126 5.3 EU 0.5 2 2 1 EU 7.5 219 7.5
8 121 5.7 EU 2 2 2 EU 8 210 8
8.5 115 6.0 EU 0.5 2 2 2 EU 8.5 200 8.5
9 110 6.4 EU 2 2 2 1 EU 9 190 9
9.5 103 6.8 EU 0.5 1 4 2 EU 9.5 180 9.5
10 96 7.1 EU 4 4 EU 10 170 10
10.5 89 7.5 EU 4 4 0.5 EU 10.5 156 10.5
11 82 7.8 EU 4 4 1 EU 11 142 11
11.5 75 8.2 EU 1 4 4 0.5 EU 11.5 133 11.5
12 72 8.5 EU 2 4 4 EU 12 125 12
12.5 66 9.0 EU 2 4 4 0.5 EU 12.5 114 12.5
13 60 9.5 EU 2 4 4 1 EU 13 104 13
13.5 57 9.75 EU 2 4 4 1 0.5 EU 13.5 98 13.5
14 53 10.0 EU 4 4 4 EU 14 92 14
14.5 48 10.25 EU 0.5 4 4 4 EU 14.5 84 14.5

15 44 10.5 EU 4 4 4 1 EU 15 76 15

15.5 41 11.0 EU 0.5 4 4 4 1 EU 15.5 71 15.5

16 38 11.5 EU 4 4 4 2 EU 16 66 16

30 Email: [email protected] www.modulift.com

 MOD 110/70: Step-Downs

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 110/70 has an assembled span
ranging from 1 metre to 16 metres in 0.5 metre increments.

ß =’Sling to Vertical’ angle

P7
P3 - P6
b

P1
P8 P9 P2
Span

Fig.1: Typical Spreader Assembly.

Larger shackle

Smaller shackle
END UNIT
STEP DOWN STRUT
DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended 30º STV
Sling Angle Format
Part ref: Description
Span SWL Min Top Configuration. ISA Span SWL Min Top
/m /t sling EU - End Unit (0.5m) /m /t sling P1 END UNIT (STEP DOWN)
Length / m STV = ‘SLING TO STV

BSA
Length / m
VERTICAL’ ANGLE, ß P2 DROP LINK (MOD 70)
2 70 1.5 EU EU 2 70 2
P3 4.0m STRUT
2.5 70 2.0 EU 0.5 EU 2.5 70 2.5
3 70 2.5 EU 1 EU 3 70 3 P4 2.0m STRUT
3.5 70 2.8 EU 1 0.5 EU 3.5 70 3.5 P5 1.0m STRUT
4 70 3.0 EU 2 EU 4 70 4
P6 0.5m STRUT
4.5 70 3.3 EU 2 1 EU 4.5 70 4.5
P7 55t SHACKLE
5 70 3.5 EU 2 1 EU 5 70 5
5.5 70 4.0 EU 0.5 2 1 EU 5.5 70 5.5 P8 35t SHACKLE
6 70 4.5 EU 4 EU 6 70 6 P9 M20x65 HT BOLTS,
6.5 70 4.8 EU 2 2 0.5 EU 6.5 70 6.5 NUTS & WASHERS
7 70 5.0 EU 4 1 EU 7 70 7
7.5 70 5.5 EU 0.5 2 2 1 EU 7.5 70 7.5
8 70 6.0 EU 4 2 EU 8 70 8
8.5 70 6.5 EU 0.5 2 2 2 EU 8.5 70 8.5 Mod 110/70 - SYSTEM Specification
9 70 6.5 EU 4 2 1 EU 9 70 9
• Rated at 70 tonnes SWL at 10m
9.5 70 6.8 EU 0.5 1 4 2 EU 9.5 70 9.5
span
10 70 7.0 EU 4 4 EU 10 70 10
10.5 70 7.5 EU 4 4 0.5 EU 10.5 70 10.5 • ‘Sling to Vertical’ angle, ß, 45 degrees
11 66 8.0 EU 4 4 1 EU 11 70 11 or less
11.5 62 8.3 EU 1 4 1 0.5 EU 11.5 70 11.5
12 58 8.5 EU 4 4 2 EU 12 70 12
• End units and drop links are rated at
12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 70 12.5 35 tonnes (70 tonnes combined
13 48 9.5 EU 1 4 4 2 EU 13 70 13 capacity)
13.5 45 9.8 EU 2 4 4 1 0.5 EU 13.5 70 13.5
• Bolt tightening torque: 150Nm
14 43 10.0 EU 4 4 4 EU 14 70 14
14.5 39 10.3 EU 0.5 4 4 4 EU 14.5 67 14.5
Spanner size required: 30mm
15 35 10.5 EU 4 4 4 1 EU 15 62 15
15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5
16 31 11.5 EU 4 4 4 2 EU 16 53 16

Email: [email protected] www.modulift.com 31

 MOD 110/50: Step-Downs

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 110/50 has an assembled span
ranging from 1 metre to 16 metres in 0.5 metre increments.

ß =’Sling to Vertical’ angle

P7
P3 - P6
b

P1
P8 P9 P2
Span
Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT Smaller shackle

STEP DOWN STRUT
DROP LINK SUB-ASSY

Load v Span Component list

45˚ STV Recommended 30˚ STV Part ref: Description
Sling Angle Format

Configuration
Span SWL Min Top Span SWL Min Top
ISA

EU - End Unit (1m)

STV = ‘SLING TO VERTICAL’
P1 END UNIT (STEP DOWN)
/m /t sling STV /m /t Sling
Length / m ANGLE , ß Length / m
BSA

P2 DROP LINK (MOD 50)

2 110 1.5 EU EU 2 110 2
P3 4.0m STRUT
2.5 110 1.8 EU 0.5 EU 2.5 110 2.5
P4 2.0m STRUT
3 110 2.2 EU 1 EU 3 110 3
3.5 110 2.5 EU 1 0.5 EU 3.5 110 3.5
P5 1.0m STRUT
4 110 2.9 EU 2 EU 4 110 4 P6 0.5m STRUT
4.5 110 3.2 EU 2 0.5 EU 4.5 110 4.5 P7 35t SHACKLE
5 110 3.6 EU 2 1 EU 5 110 5 P8 25t SHACKLE
5.5 110 3.9 EU 0.5 2 1 EU 5.5 110 5.5
P9 M20x65 HT BOLTS,
6 110 4.3 EU 2 2 EU 6 110 6
NUTS & WASHERS
6.5 109 4.6 EU 2 2 0.5 EU 6.5 110 6.5
7 106 5.0 EU 2 2 1 EU 7 110 7
7.5 102 5.3 EU 0.5 2 2 1 EU 7.5 110 7.5
8 98 5.7 EU 2 2 2 EU 8 110 8 Mod 110/50 - SYSTEM Specification
8.5 93 6.0 EU 0.5 2 2 2 EU 8.5 110 8.5
• Rated at 50 tonnes SWL at 16m
9 88 6.4 EU 2 2 2 1 EU 9 110 9
span
9.5 83 6.8 EU 0.5 1 4 2 EU 9.5 110 9.5
10 78 7.1 EU 4 4 EU 10 110 10 • ‘Sling to Vertical’ angle, ß, 45 degrees
10.5 72 7.5 EU 4 4 0.5 EU 10.5 110 10.5 or less
11 66 7.8 EU 4 4 1 EU 11 110 11 • End units and drop links are rated at
11.5 62 8.2 EU 0.5 4 4 1 EU 11.5 107 11.5 25 tonnes (50 tonnes combined
12 58 8.5 EU 2 4 4 EU 12 100 12 capacity)
12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 92 12.5
13 48 9.5 EU 2 4 4 1 EU 13 84 13
• Bolt tightening torque: 150Nm
Spanner size required: 30mm
13.5 45 9.75 EU 2 4 4 1 0.5 EU 13.5 80 13.5
14 43 10.0 EU 4 4 4 EU 14 75 14
14.5 39 10.25 EU 0.5 4 4 4 EU 14.5 69 14.5
15 35 10.5 EU 4 4 4 1 EU 15 62 15
15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5
16 31 11.5 EU 4 4 4 2 EU 16 53 16

32 Email: [email protected] www.modulift.com

 MOD 250/250

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 250/250 has an
assembled span ranging from 2 metres to 20m in 1m increments.

Component list ß =’Sling to Vertical’ angle

Part ref: Description b P8

P3 - P7
P1 END UNIT WLL 125t
P2 DROP LINK WLL 125t
P3 6m STRUT
P1
P9
P4 3m STRUT P9 P10 P2
Span
P5 2m STRUT
Fig. 1: Typical Spreader Assembly.
P6 1m STRUT
P7 0.5m STRUT
P8 200t WIDE BODY SHACKLE Larger shackle

P9 125t WIDE BODY SHACKLE

P10 M24X80 GRADE 8.8, HT BOLTS, END UNIT

STRUT SUB-ASSY
Smaller shackle
NUTS & WASHERS DROP LINK

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 250/250 - SYSTEM
/m /t sling STV = ‘SLING TO STV
/m /t sling Specification
Length / m VERTICAL’ ANGLE, ß
BSA
Length / m
• Rated at 250 tonnes SWL at 13m span
2 250 1.5 EU EU 2 250 2
3 250 2.5 EU 1 EU 3 250 3 • ‘Sling to Vertical’ angle, ß, 45 degrees
or less
4 250 3.0 EU 2 EU 4 250 4
5 250 3.5 EU 3 EU 5 250 5 • End units and drop links are rated at
6 250 4.5 EU 3 1 EU 6 250 6
125 tonnes (250 tonnes combined
capacity)
7 250 5.0 EU 3 2 EU 7 250 7
8 244 6.0 EU 6 EU 8 250 8 • Bolt tightening torque: 250Nm
9 228 6.5 EU 6 1 EU 9 250 9 Spanner size required: 36mm
10 212 7.0 EU 6 2 EU 10 250 10
11 194 8.0 EU 6 3 EU 11 250 11
12 178 8.5 EU 3 6 1 EU 12 250 12
13 158 9.5 EU 3 6 2 EU 13 250 13
14 140 10.0 EU 6 6 EU 14 242 14
15 122 10.5 EU 6 6 1 EU 15 211 15
16 106 11.5 EU 6 6 2 EU 16 183 16
17 94 12.0 EU 6 6 3 EU 17 163 17
18 82 13.0 EU 1 6 6 3 EU 18 142 18
19 70 13.5 EU 2 6 6 3 EU 19 121 19
20 52 14.5 EU 2 6 6 3 1 EU 20 90 20

Email: [email protected] www.modulift.com 33

 MOD 250/300

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 250/300 has an
assembled span ranging from 2 metres to 20m in 1m increments.

Component list β =’Sling to Vertical’ angle

Part ref: Description b P8

P3 - P7
P1 END UNIT WLL 150t
P2 DROP LINK WLL 150t
P3 6m STRUT
P9
P1 P10
P4 3m STRUT P9 P2
Span
P5 2m STRUT
Fig. 1: Typical Spreader Assembly.
P6 1m STRUT
P7 0.5m STRUT
P8 200t WIDE BODY SHACKLE Larger shackle
P9 150t WIDE BODY SHACKLE

P10 M24X80 GRADE 8.8, HT BOLTS, END UNIT

NUTS & WASHERS STRUT SUB-ASSY
DROP LINK Smaller shackle

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Span SWL Min Top
Configuration
EU - End Unit (1m)
ISA
Span SWL Min Top Mod 250/300 - SYSTEM
/m /t sling STV = ‘SLING TO STV
/m /t sling Specification
Length / m Length / m
VERTICAL’ ANGLE, ß
BSA

• Rated at 300 tonnes SWL at 12m

2 278 1.5 EU EU 2 300 2 span
3 278 2.5 EU 1 EU 3 300 3
• ‘Sling to Vertical’ angle, ß, 45 degrees
4 278 3.0 EU 2 EU 4 300 4
or less
5 272 3.5 EU 3 EU 5 300 5
• End units and drop links are rated at
6 264 4.5 EU 3 1 EU 6 300 6
150 tonnes (300 tonnes combined
7 254 5.0 EU 3 2 EU 7 300 7
capacity)
8 244 6.0 EU 6 EU 8 300 8
• Bolt tightening torque: 250Nm
9 228 6.5 EU 6 1 EU 9 300 9
Spanner size required: 36mm
10 212 7.0 EU 6 2 EU 10 300 10
11 194 8.0 EU 6 3 EU 11 300 11
12 178 8.5 EU 3 6 1 EU 12 300 12
13 158 9.5 EU 3 6 2 EU 13 273 13
14 140 10.0 EU 6 6 EU 14 242 14
15 122 10.5 EU 6 6 1 EU 15 211 15
16 106 11.5 EU 6 6 2 EU 16 183 16
17 94 12.0 EU 6 6 3 EU 17 163 17
18 82 13.0 EU 1 6 6 3 EU 18 142 18
19 70 13.5 EU 2 6 6 3 EU 19 121 19
20 52 14.5 EU 3 6 6 2 1 EU 20 90 20

34 Email: [email protected] www.modulift.com

 MOD 250/400

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 250/400 has an
assembled span ranging from 2 metres to 20m in 1m increments.

Component list β =’Sling to Vertical’ angle

b P8
Part ref: Description P3 - P7
P1 END UNIT WLL 200t
P2 DROP LINK WLL 200t
P3 6m STRUT P1
P9 P4 3m STRUT P10 P2
P9 Span
P5 2m STRUT
Fig. 1: Typical Spreader Assembly.
P6 1m STRUT
P7 0.5m STRUT
Larger shackle
P8 300t WIDE BODY SHACKLE
P9 200t WIDE BODY SHACKLE
END UNIT
P10 M24X80 GRADE 8.8, HT BOLTS, STRUT SUB-ASSY Smaller shackle
DROP LINK
NUTS & WASHERS

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 250/400 - SYSTEM
/m /t sling /m /t sling
Length / m
STV = ‘SLING TO STV

BSA Length / m
Specification
VERTICAL’ ANGLE, ß
• Rated at 400 tonnes SWL at 8m span
2 300 1.5 EU EU 2 400 2
3 284 2.5 EU 1 EU 3 400 3
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
4 278 3.0 EU 2 EU 4 400 4
5 272 3.5 EU 3 EU 5 400 5 • End units and drop links are rated at
6 264 4.5 EU 3 1 EU 6 400 6
200 tonnes (400 tonnes combined
capacity)
7 254 5.0 EU 3 2 EU 7 400 7
8 244 6.0 EU 6 EU 8 400 8 • Bolt tightening torque: 250Nm
9 228 6.5 EU 6 1 EU 9 394 9
Spanner size required: 36mm
10 212 7.0 EU 6 2 EU 10 367 10
11 194 8.0 EU 6 3 EU 11 336 11
12 178 8.5 EU 3 6 1 EU 12 308 12
13 158 9.5 EU 3 6 2 EU 13 273 13
14 140 10.0 EU 6 6 EU 14 242 14
15 122 10.5 EU 6 6 1 EU 15 211 15
16 106 11.5 EU 6 6 2 EU 16 183 16
17 94 12.0 EU 6 6 3 EU 17 163 17
18 82 13.0 EU 1 6 6 3 EU 18 142 18
19 70 13.5 EU 2 6 6 3 EU 19 121 19
20 52 14.5 EU 3 6 6 2 1 EU 20 90 20

Email: [email protected] www.modulift.com 35

 MOD 250/110H: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 250/110H has an assembled span
ranging from 2 metres to 20 metres in 1 metre increments.

β =’Sling to Vertical’ angle

P8
P3 - P7 P9
b P1

P10 P2
Span
Fig.1: Typical Spreader Assembly.

Larger shackle

Smaller shackle
END UNIT
CONE ADAPTER STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV Part ref: Description
Configuration.
Span SWL Min Top EU - End Unit (1m) ISA Span SWL Min Top P1 END UNIT - MOD 110H WLL 85t
/m /t sling CA - Cone Adaptor (0.5m) /m /t sling
Length / m STV

BSA
Length / m P2 DROP LINK - MOD 110H WLL 85t
P3 6.0m STRUT
2 170 1.5 EU EU 2 170 2
P4 3.0m STRUT
3 170 2.5 EU CA CA EU 3 170 3
P5 2.0m STRUT
4 170 3.0 EU CA 1 CA EU 4 170 4
5 170 3.5 EU CA 2 CA EU 5 170 5 P6 1.0m STRUT
6 170 4.5 EU CA 3 CA EU 6 170 6 P7 0.5 STRUT
7 170 5.0 EU CA 3 1 CA EU 7 170 7
P8 MOD 250/110 CONE ADAPTER
8 170 6.0 EU CA 3 2 CA EU 8 170 8
9 170 6.5 EU CA 6 CA EU 9 170 9
P9 120t SHACKLE
10 170 7.0 EU CA 6 1 CA EU 10 170 10 P10 85t SHACKLE
11 170 8.0 EU CA 6 2 CA EU 11 170 11 P11 MOD 250: M24x80 HT BOLTS, NUTS
12 170 8.5 EU CA 6 3 CA EU 12 170 12 & WASHERS
MOD 110H: M20x65 HT BOLTS,
13 158 9.5 EU CA 3 6 1 CA EU 13 170 13
NUTS & WASHERS
14 140 10.0 EU CA 3 6 2 CA EU 14 170 14
15 122 10.5 EU CA 6 6 CA EU 15 170 15
16 106 11.5 EU CA 6 6 1 CA EU 16 170 16
Mod 250/110H - SYSTEM
17 94 12.0 EU CA 6 6 2 CA EU 17 163 17
Specification
18 82 13.0 EU CA 6 6 3 CA EU 18 142 18
19 70 13.5 EU CA 1 6 6 3 CA EU 19 121 19 • Rated at 170 tonnes SWL at 16m
20 52 14.5 EU CA 2 6 6 3 CA EU 20 90 20 span
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
• End units and drop links are rated at
85 tonnes (170 tonnes combined
capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

36 Email: [email protected] www.modulift.com

 MOD 250/110: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 250/110 has an assembled span
ranging from 2 metres to 20 metres in 1 metre increments.

β =’Sling to Vertical’ angle P8

P3 - P7 P9
b P1

P2
P10 Span
Fig.1: Typical Spreader Assembly.

Larger shackle

CONE ADAPTER STRUT DROP LINK Smaller shackle

END UNIT
SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV Part ref: Description
Configuration.
Span SWL Min Top Span SWL Min Top
/m /t sling
EU - End Unit (1m) ISA

/m /t sling
P1 END UNIT - MOD 110 WLL 55t
CA - Cone Adaptor (0.5m)
Length / m STV
Length / m P2 DROP LINK - MOD 110 WLL 55t
BSA

P3 6.0m STRUT
2 110 1.5 EU EU 2 110 2
3 110 2.5 EU CA CA EU 3 110 3 P4 3.0m STRUT
4 110 3.0 EU CA 1 CA EU 4 110 4 P5 2.0m STRUT
5 110 3.5 EU CA 2 CA EU 5 110 5
P6 1.0m STRUT
6 110 4.5 EU CA 3 CA EU 6 110 6
7 110 5.0 EU CA 3 1 CA EU 7 110 7
P7 MOD 250/110 CONE ADAPTER
8 110 6.0 EU CA 3 2 CA EU 8 110 8 P8 85t SHACKLE
9 110 6.5 EU CA 6 CA EU 9 110 9
P9 55t SHACKLE
10 110 7.0 EU CA 6 1 CA EU 10 110 10
P10 MOD 250: M24x80 HT BOLTS, NUTS
11 110 8.0 EU CA 6 2 CA EU 11 110 11
& WASHERS
12 110 8.5 EU CA 6 3 CA EU 12 110 12 MOD 110: M20x65 HT BOLTS, NUTS
13 110 9.5 EU CA 3 6 1 CA EU 13 110 13 & WASHERS
14 110 10.0 EU CA 3 6 2 CA EU 14 110 14
15 110 10.5 EU CA 6 6 CA EU 15 110 15
16 106 11.5 EU CA 6 6 1 CA EU 16 110 16 Mod 250/110 - SYSTEM
17 94 12.0 EU CA 6 6 2 CA EU 17 110 17
Specification
18 82 13.0 EU CA 6 6 3 CA EU 18 110 18
19 70 13.5 EU CA 1 6 6 3 CA EU 19 110 19
• Rated at 110 tonnes SWL at 15m
20 52 14.5 EU CA 2 6 6 3 CA EU 20 90 20 span
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
• End units and drop links are rated at
55 tonnes (110 tonnes combined
capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

Email: [email protected] www.modulift.com 37

 MOD 250/70H: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 250/70H has an assembled span
ranging from 1 metre to 20 metres in 0.5 metre increments.

β =’Sling to Vertical’ angle

P11 P8 P9
P3 - P7
b P1

P10 P2
Span
Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT
SUB-ASSY Smaller shackle
CONE ADAPTER STRUT DROP LINK

Load v Span Component list

45º STV Recommended Sling Angle Format
30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top
P1 END UNIT - MOD 70H WLL 50t
ISA

/m /t sling EU - End Unit (1m) /m /t sling

Length / m CA - Cone Adaptor (0.5m) STV
Length / m
BSA P2 DROP LINK - MOD 70H WLL 50t

1 100 0.8 EU EU 1 100 1 P3 6.0m STRUT

2 100 1.5 EU CA CA EU 2 100 2 P4 3.0m STRUT
3 100 2.5 EU CA 1 CA EU 3 100 3 P5 2.0m STRUT
4 100 3.0 EU CA 2 CA EU 4 100 4 P6 1.0m STRUT
5 100 3.5 EU CA 3 CA EU 5 100 5
P7 MOD 250/70 CONE ADAPTER
6 100 4.5 EU CA 3 1 CA EU 6 100 6
7 100 5.0 EU CA 3 2 CA EU 7 100 7
P8 85t SHACKLE
8 100 6.0 EU CA 6 CA EU 8 100 8 P9 55t SHACKLE
9 100 6.5 EU CA 6 1 CA EU 9 100 9 P10 MOD 250: M24x80 HT BOLTS, NUTS
10 100 7.0 EU CA 6 2 CA EU 10 100 10 & WASHERS
MOD 70H: M20x65 HT BOLTS, NUTS
11 100 8.0 EU CA 6 3 CA EU 11 100 11 & WASHERS
12 100 8.5 EU CA 3 6 1 CA EU 12 100 12
13 100 9.5 EU CA 3 6 2 CA EU 13 100 13
14 100 10.0 EU CA 6 6 CA EU 14 100 14 Mod 250/70H - SYSTEM
15 100 10.5 EU CA 6 6 1 CA EU 15 100 15 Specification
16 100 11.5 EU CA 6 6 2 CA EU 16 100 16
• Rated at 100 tonnes SWL at 16m
17 94 12.0 EU CA 6 6 3 CA EU 17 100 17
span
18 82 13.0 EU CA 1 6 6 3 CA EU 18 100 18
19 70 13.5 EU CA 2 6 6 3 CA EU 19 100 19 • ‘Sling to Vertical’ angle, ß, 45 degrees
20 52 14.5 EU CA 2 6 6 3 CA EU 20 90 20 or less
• End units and drop links are rated at
50 tonnes (100 tonnes combined
capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

38 Email: [email protected] www.modulift.com

 MOD 250/70: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 250/70 has an assembled span
ranging from 1 metre to 20 metres in 0.5 metre increments.

β =’Sling to Vertical’ angle

P11 P8 P9
b P3 - P7 P1

P10 P2
Span

Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT Smaller shackle

CONE ADAPTER STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format 30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top
EU - End Unit (1m)
ISA
P1 END UNIT - MOD 70 WLL 35t
/m /t sling /m /t sling
Length / m CA - Cone Adaptor (0.5m) Length / m P2 DROP LINK - MOD 70 WLL 35t
STV

BSA

1 70 0.8 EU EU 1 70 1 P3 6.0m STRUT

2 70 1.5 EU CA CA EU 2 70 2 P4 3.0m STRUT
3 70 2.5 EU CA 1 CA EU 3 70 3 P5 2.0m STRUT
4 70 3.0 EU CA 2 CA EU 4 70 4 P6 1.0m STRUT
5 70 3.5 EU CA 3 CA EU 5 70 5
P7 MOD 250/70 CONE ADAPTER
6 70 4.5 EU CA 3 1 CA EU 6 70 6
P8 55t SHACKLE
7 70 5.0 EU CA 3 2 CA EU 7 70 7
8 70 6.0 EU CA 6 CA EU 8 70 8 P9 35t SHACKLE
9 70 6.5 EU CA 6 1 CA EU 9 70 9 P10 MOD 250: M24x80 HT BOLTS, NUTS
10 70 7.0 EU CA 6 2 CA EU 10 70 10 & WASHERS
MOD 70H M20x65 HT BOLTS, NUTS
11 70 8.0 EU CA 6 3 CA EU 11 70 11 & WASHERS
12 70 8.5 EU CA 3 6 1 CA EU 12 70 12
13 70 9.5 EU CA 3 6 2 CA EU 13 70 13
14 70 10.0 EU CA 6 6 CA EU 14 70 14 Mod 250/70 - SYSTEM Specification
15 70 10.5 EU CA 6 6 1 CA EU 15 70 15 • Rated at 70 tonnes SWL at 19m
16 70 11.5 EU CA 6 6 2 CA EU 16 70 16 span
17 70 12.0 EU CA 6 6 3 CA EU 17 70 17
18 70 13.0 EU CA 1 6 6 3 CA EU 18 70 18
• ‘Sling to Vertical’ angle, ß, 45 degrees
19 70 13.5 EU CA 2 6 6 3 CA EU 19 70 19
or less
20 52 14.5 EU CA 2 6 6 3 CA EU 20 70 20 • End units and drop links are rated at
35 tonnes (70 tonnes combined
capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

Email: [email protected] www.modulift.com 39

 MOD 400/400

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 400/400 has an
assembled span ranging from 2 metres to 23m in 1m increments.

Component list β =’Sling to Vertical’ angle

Part ref: Description b P8
P1 END UNIT WLL 200t P3 - P7

P2 DROP LINK WLL 200t

P3 6m STRUT
P4 3m STRUT P1
P9 P10 P2
P9 Span
P5 2m STRUT
P6 1m STRUT Fig. 1: Typical Spreader Assembly.
P7 0.5m STRUT
P8 300t WIDE BODY SHACKLE Larger shackle

P9 200t WIDE BODY SHACKLE

P10 M24X90 GRADE 8.8, HT BOLTS, END UNIT

NUTS & WASHERS STRUT SUB-ASSY Smaller shackle
DROP LINK

Load v Span
45˚ STV Recommended Sling Angle Format 30˚ STV
Span SWL Min Top
Configuration
ISA
Span SWL Min Top Mod 400/400 - SYSTEM
EU - End Unit (1m)
/m /t sling STV = ‘SLING TO STV
/m /t sling Specification
Length / m BSA Length / m
VERTICAL’ ANGLE, ß
• Rated at 400 tonnes SWL at 16m span
2 400 1.5 EU EU 2 400 2
• ‘Sling to Vertical’ angle, ß, 45 degrees
3 400 2.5 EU 1 EU 3 400 3
or less
4 400 3.0 EU 2 EU 4 400 4
5 400 3.5 EU 3 EU 5 400 5
• End units and drop links are rated at
200 tonnes (400 tonnes combined
6 400 4.5 EU 3 1 EU 6 400 6
capacity)
7 400 5.0 EU 3 2 EU 7 400 7
8 400 6.0 EU 6 EU 8 400 8 • Bolt tightening torque: 250Nm
9 400 6.5 EU 6 1 EU 9 400 9
Spanner size required: 36mm
10 384 7.0 EU 6 2 EU 10 400 10
11 365 8.0 EU 6 3 EU 11 400 11
12 350 8.5 EU 3 6 1 EU 12 400 12
13 327 9.5 EU 3 6 2 EU 13 400 13
14 303 10.0 EU 6 6 EU 14 400 14
15 278 11.0 EU 6 6 1 EU 15 400 15
16 250 11.5 EU 6 6 2 EU 16 400 16
17 227 12.0 EU 6 6 3 EU 17 393 17
18 205 13.0 EU 1 6 6 3 EU 18 355 18
19 183 13.5 EU 2 6 6 3 EU 19 317 19
20 161 14.5 EU 6 6 6 EU 20 279 20
21 145 15.0 EU 6 6 6 1 EU 21 251 21
22 133 16.0 EU 6 6 6 2 EU 22 230 22
23 116 16.5 EU 6 6 6 3 EU 23 200 23

40 Email: [email protected] www.modulift.com

 MOD 400/500

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 400/500 has an
assembled span ranging from 2 metres to 23m in 1m increments.

Component list β =’Sling to Vertical’ angle

Part ref: Description b P8

P3 - P7
P1 END UNIT WLL 250t
P2 DROP LINK WLL 250t
P3 6m STRUT
P1
P9 P4 3m STRUT P10 P2
P9 Span
P5 2m STRUT
Fig. 1: Typical Spreader Assembly.
P6 1m STRUT
P7 0.5m STRUT
P8 300t WIDE BODY SHACKLE Larger shackle

P9 250t WIDE BODY SHACKLE

P10 M24X90 GRADE 8.8, HT BOLTS, END UNIT

STRUT
NUTS & WASHERS DROP LINK SUB-ASSY Smaller shackle

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 400/500 - SYSTEM
/m /t sling STV = ‘SLING TO STV /m /t sling Specification
Length / m VERTICAL’ ANGLE, ß
BSA
Length / m
• Rated at 500 tonnes SWL at 14m span
2 420 1.5 EU EU 2 500 2
3 420 2.5 EU 1 EU 3 500 3 • ‘Sling to Vertical’ angle, ß, 45 degrees
4 420 3.0 EU 2 EU 4 500 4
or less
5 420 3.5 EU 3 EU 5 500 5 • End units and drop links are rated at
6 420 4.5 EU 3 1 EU 6 500 6 250 tonnes (500 tonnes combined
7 420 5.0 EU 3 2 EU 7 500 7
capacity)
8 413 6.0 EU 6 EU 8 500 8 • Bolt tightening torque: 250Nm
9 400 6.5 EU 6 1 EU 9 500 9 Spanner size required: 36mm
10 384 7.0 EU 6 2 EU 10 500 10
11 365 8.0 EU 6 3 EU 11 500 11
12 350 8.5 EU 3 6 1 EU 12 500 12
13 327 9.5 EU 3 6 2 EU 13 500 13
14 303 10.0 EU 6 6 EU 14 500 14
15 278 11.0 EU 6 6 1 EU 15 481 15
16 250 11.5 EU 6 6 2 EU 16 433 16
17 227 12.0 EU 6 6 3 EU 17 393 17
18 205 13.0 EU 1 6 6 3 EU 18 355 18
19 183 13.5 EU 2 6 6 3 EU 19 317 19
20 161 14.5 EU 6 6 6 EU 20 279 20
21 145 15.0 EU 6 6 6 1 EU 21 251 21
22 133 16.0 EU 6 6 6 2 EU 22 230 22
23 116 16.5 EU 6 6 6 3 EU 23 200 23

Email: [email protected] www.modulift.com 41

 MOD 400/600

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 400/600 has an
assembled span ranging from 2 metres to 23m in 1m increments.

Component list β =’Sling to Vertical’ angle

Part ref: Description b P8
P3 - P7
P1 END UNIT WLL 300t
P2 DROP LINK WLL 300t
P3 6m STRUT
P1
P9 P4 3m STRUT P10 P2
P9 Span
P5 2m STRUT
Fig. 1: Typical Spreader Assembly.
P6 1m STRUT
P7 0.5m STRUT
Larger shackle
P8 400t WIDE BODY SHACKLE
P9 300t WIDE BODY SHACKLE
END UNIT
P10 M24X90 GRADE 8.8, HT BOLTS, STRUT Smaller shackle
DROP LINK SUB-ASSY
NUTS & WASHERS

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top sling Mod 400/600 - SYSTEM
/m /t sling
Length / m
STV = ‘SLING TO STV
/m /t Length / m
Specification
VERTICAL’ ANGLE, ß
BSA

• Rated at 600 tonnes SWL at 12m

2 460 1.5 EU EU 2 600 2
span
3 456 2.5 EU 1 EU 3 600 3
4 450 3.0 EU 2 EU 4 600 4
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
5 442 3.5 EU 3 EU 5 600 5
6 434 4.5 EU 3 1 EU 6 600 6 • End units and drop links are rated at
7 424 5.0 EU 3 2 EU 7 600 7 300 tonnes (600 tonnes combined
8 413 6.0 EU 6 EU 8 600 8
capacity)
9 400 6.5 EU 6 1 EU 9 600 9 • Bolt tightening torque: 250Nm
10 384 7.0 EU 6 2 EU 10 600 10 Spanner size required: 36mm
11 365 8.0 EU 6 3 EU 11 600 11
12 350 8.5 EU 3 6 1 EU 12 600 12
13 327 9.5 EU 3 6 2 EU 13 566 13
14 303 10.0 EU 6 6 EU 14 524 14
15 278 11.0 EU 6 6 1 EU 15 481 15
16 250 11.5 EU 6 6 2 EU 16 433 16
17 227 12.0 EU 6 6 3 EU 17 393 17
18 205 13.0 EU 1 6 6 3 EU 18 355 18
19 183 13.5 EU 2 6 6 3 EU 19 317 19
20 161 14.5 EU 6 6 6 EU 20 279 20
21 145 15.0 EU 6 6 6 1 EU 21 251 21
22 133 16.0 EU 6 6 6 2 EU 22 230 22
23 116 16.5 EU 6 6 6 3 EU 23 200 23

42 Email: [email protected] www.modulift.com

 MOD 400/250: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 400/250 has an assembled span
ranging from 2 metres to 23 metres in 1 metre increments.

β =’Sling to Vertical’ angle P8

P3 - P7 P11 P9
b P1

P2
P10 Span
Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT Smaller shackle

CONE ADAPTER STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format
30º STV Part ref: Description
Span SWL Min Top Configuration. ISA
Span SWL Min Top
EU - End Unit (1m) P1 END UNIT - MOD 250 WLL 125t
/m /t sling STV
/m /t sling
Length / m CA - Cone Adaptor (0.5m) BSA Length / m P2 DROP LINK - MOD 250 WLL 125t
2 250 1.5 EU EU 2 250 2 P3 6.0m STRUT
3 250 2.5 EU CA CA EU 3 250 3 P4 3.0m STRUT
4 230 3.0 EU CA 1 CA EU 4 230 4 P5 2.0m STRUT
5 250 3.5 EU CA 2 CA EU 5 250 5 P6 1.0m STRUT
6 250 4.5 EU CA 3 CA EU 6 250 6 P7 MOD 400/250 CONE ADAPTER
7 250 5.0 EU CA 3 1 CA EU 7 250 7
P8 200t WIDE BODY SHACKLE
8 250 6.0 EU CA 3 2 CA EU 8 250 8
P9 125t WIDE BODY SHACKLE
9 230 6.5 EU CA 6 CA EU 9 230 9
P10 MOD 400: M24x90 HT BOLTS,
10 250 7.0 EU CA 6 1 CA EU 10 250 10 NUTS & WASHERS
11 250 8.0 EU CA 6 2 CA EU 11 250 11 MOD 250: M24x80 HT BOLTS,
12 250 8.5 EU CA 6 3 CA EU 12 250 12 NUTS & WASHERS

13 250 9.5 EU CA 3 6 1 CA EU 13 250 13

14 230 10.0 EU CA 3 6 2 CA EU 14 230 14
15 250 11.0 EU CA 6 6 CA EU 15 250 15
Mod 400/250 - SYSTEM
16 250 11.5 EU CA 6 6 1 CA EU 16 250 16
Specification
17 227 12.0 EU CA 6 6 2 CA EU 17 250 17 • Rated at 12 tonnes SWL at 10.5m
18 205 13.0 EU CA 6 6 3 CA EU 18 230 18 span
19 183 13.5 EU CA 3 6 6 1 CA EU 19 250 19 • ‘Sling to Vertical’ angle, ß, 45 degrees
20 161 14.5 EU CA 3 6 6 2 CA EU 20 250 20 or less
21 145 15.0 EU CA 6 6 6 CA EU 21 250 21
• End units and drop links are rated at
22 133 16.0 EU CA 6 6 6 1 CA EU 22 230 22
6 tonnes (12 tonnes combined
23 116 16.5 EU CA 6 6 6 2 CA EU 23 200 23
capacity)
• Bolt tightening torque: 150Nm
Spanner size required: 30mm

Email: [email protected] www.modulift.com 43

 MOD 400/110SH: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 400/110SH has an assembled span
ranging from 2 metres to 23 metres in 1 metre increments.

β =’Sling to Vertical’ angle

P8
P3 - P7 P9
b P1

P11 P2
P10 Span
Fig.1: Typical Spreader Assembly.
Larger shackle

Smaller shackle
STRUT END UNIT
CONE ADAPTER DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format
30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top P1 END UNIT - MOD 110SH WLL 120t
ISA

/m /t sling EU - End Unit (1m) /m /t sling

CA - Cone Adaptor (0.5m)
STV

Length / m BSA Length / m P2 DROP LINK - MOD 110SH WLL 120t

2 240 1.5 EU EU 2 240 2 P3 6.0m STRUT
3 240 2.5 EU CA CA EU 3 240 3 P4 3.0m STRUT
4 240 3.0 EU CA 1 CA EU 4 240 4 P5 2.0m STRUT
5 240 3.5 EU CA 2 CA EU 5 240 5 P6 1.0m STRUT
6 240 4.5 EU CA 3 CA EU 6 240 6 P7 MOD 400/110 CONE ADAPTER
7 240 5.0 EU CA 3 1 CA EU 7 240 7
P8 150t SHACKLE
8 240 6.0 EU CA 3 2 CA EU 8 240 8
P9 120t SHACKLE
9 240 6.5 EU CA 6 CA EU 9 240 9
P10 MOD 400: M24x90 HT BOLTS,
10 240 7.0 EU CA 6 1 CA EU 10 240 10 NUTS & WASHERS
11 240 8.0 EU CA 6 2 CA EU 11 240 11 MOD 110: M20x65 HT BOLTS,
12 240 8.5 EU CA 6 3 CA EU 12 240 12
NUTS & WASHERS

13 240 9.5 EU CA 3 6 1 CA EU 13 240 13

14 240 10.0 EU CA 3 6 2 CA EU 14 240 14 Mod 400/110SH - SYSTEM
15 240 11.0 EU CA 6 6 CA EU 15 240 15 Specification
16 240 11.5 EU CA 6 6 1 CA EU 16 240 16
• Rated at 240 tonnes SWL at 21m
17 227 12.0 EU CA 6 6 2 CA EU 17 240 17
span
18 205 13.0 EU CA 6 6 3 CA EU 18 240 18
19 183 13.5 EU CA 3 6 6 1 CA EU 19 240 19 • ‘Sling to Vertical’ angle, ß, 45 degrees
20 161 14.5 EU CA 3 6 6 2 CA EU 20 240 20
or less
21 145 15.0 EU CA 6 6 6 CA EU 21 240 21 • End units and drop links are rated at
22 133 16.0 EU CA 6 6 6 1 CA EU 22 230 22 120 tonnes (240 tonnes combined
23 116 16.5 EU CA 6 6 6 2 CA EU 23 200 23 capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

44 Email: [email protected] www.modulift.com

 MOD 400/110H: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 400/110H has an assembled span
ranging from 2 metres to 23 metres in 1 metre increments.

β =’Sling to Vertical’ angle

P8
P3 - P7 P9
b P1

P11 P2
P10 Span
Fig.1: Typical Spreader Assembly.

Larger shackle

END UNIT Smaller shackle

CONE ADAPTER STRUT DROP LINK SUB-ASSY

Load v Span Component list

45º STV Recommended Sling Angle Format
30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top P1 END UNIT - MOD 110H WLL 120t
ISA

/m /t sling EU - End Unit (1m) /m /t sling

CA - Cone Adaptor (0.5m)
STV

Length / m BSA Length / m P2 DROP LINK - MOD 110H WLL 120t

2 240 1.5 EU EU 2 240 2 P3 6.0m STRUT

3 240 2.5 EU CA CA EU 3 240 3 P4 3.0m STRUT
4 240 3.0 EU CA 1 CA EU 4 240 4 P5 2.0m STRUT
5 240 3.5 EU CA 2 CA EU 5 240 5 P6 1.0m STRUT
6 240 4.5 EU CA 3 CA EU 6 240 6 P7 MOD 400/110 CONE ADAPTER
7 240 5.0 EU CA 3 1 CA EU 7 240 7 P8 150t SHACKLE
8 240 6.0 EU CA 3 2 CA EU 8 240 8
P9 120t SHACKLE
9 240 6.5 EU CA 6 CA EU 9 240 9
P10 MOD 400: M24x90 HT BOLTS,
10 240 7.0 EU CA 6 1 CA EU 10 240 10 NUTS & WASHERS
11 240 8.0 EU CA 6 2 CA EU 11 240 11 MOD 110: M20x65 HT BOLTS,
NUTS & WASHERS
12 240 8.5 EU CA 6 3 CA EU 12 240 12
13 240 9.5 EU CA 3 6 1 CA EU 13 240 13
14 240 10.0 EU CA 3 6 2 CA EU 14 240 14 Mod 400/110H - SYSTEM
15 240 11.0 EU CA 6 6 CA EU 15 240 15 Specification
16 240 11.5 EU CA 6 6 1 CA EU 16 240 16
• Rated at 240 tonnes SWL at 21m
17 227 12.0 EU CA 6 6 2 CA EU 17 240 17 span
18 205 13.0 EU CA 6 6 3 CA EU 18 240 18
19 183 13.5 EU CA 3 6 6 1 CA EU 19 240 19
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
20 161 14.5 EU CA 3 6 6 2 CA EU 20 240 20
21 145 15.0 EU CA 6 6 6 CA EU 21 240 21 • End units and drop links are rated at
22 133 16.0 EU CA 6 6 6 1 CA EU 22 230 22 120 tonnes (240 tonnes combined
23 116 16.5 EU CA 6 6 6 2 CA EU 23 200 23 capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

Email: [email protected] www.modulift.com 45

 MOD 400/110: Hybrid

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be assembled to achieve different spans. The Modulift 400/110 has an assembl
ranging from 2 metres to 23 metres in 0.5 metre increments.

β =’Sling to Vertical’ angle

P8
P3 - P7 P9
b P1

P10 P11 P2
Span
Fig.1: Typical Spreader Assembly.
Fig.1: Typical Spreader Assembly.
Larger shackle

END UNIT
CONE ADAPTER STRUT DROP LINK SUB-ASSY Smaller shackle

Load v Span Component list

45º STV Recommended Sling Angle Format
30º STV Part ref: Description
Span SWL Min Top Configuration. Span SWL Min Top P1 END UNIT - MOD 110H WLL 55t
ISA

/m /t sling EU - End Unit (1m) /m /t sling

CA - Cone Adaptor (0.5m)
STV

Length / m BSA Length / m P2 DROP LINK - MOD 110H WLL 55t

2 110 1.5 EU EU 2 110 2 P3 6.0m STRUT
3 110 2.5 EU CA CA EU 3 110 3 P4 3.0m STRUT
4 110 3.0 EU CA 1 CA EU 4 110 4 P5 2.0m STRUT
5 110 3.5 EU CA 2 CA EU 5 110 5 P6 1.0m STRUT
6 110 4.5 EU CA 3 CA EU 6 110 6 P7 0.5m STRUT
7 110 5.0 EU CA 3 1 CA EU 7 110 7
P8 MOD 400/110 CONE ADAPTER
8 110 6.0 EU CA 3 2 CA EU 8 110 8
P9 85t SHACKLE
9 110 6.5 EU CA 6 CA EU 9 110 9
P10 55t SHACKLE
10 110 7.0 EU CA 6 1 CA EU 10 110 10
P11 MOD 400: M24x90 HT BOLTS,
11 110 8.0 EU CA 6 2 CA EU 11 110 11
NUTS & WASHERS
12 110 8.5 EU CA 6 3 CA EU 12 110 12 MOD 110: M20x65 HT BOLTS,
13 110 9.5 EU CA 3 6 1 CA EU 13 110 13 NUTS & WASHERS
14 110 10.0 EU CA 3 6 2 CA EU 14 110 14 Mod 400/110 - SYSTEM
15 110 11.0 EU CA 6 6 CA EU 15 110 15 Specification
16 110 11.5 EU CA 6 6 1 CA EU 16 110 16
• Rated at 110 tonnes SWL at 23m
17 110 12.0 EU CA 6 6 2 CA EU 17 110 17
span
18 110 13.0 EU CA 6 6 3 CA EU 18 110 18
19 110 13.5 EU CA 3 6 6 1 CA EU 19 110 19 • ‘Sling to Vertical’ angle, ß, 45 degrees
20 110 14.5 EU CA 3 6 6 2 CA EU 20 110 20
or less
21 110 15.0 EU CA 6 6 6 CA EU 21 110 21 • End units and drop links are rated at
22 110 16.0 EU CA 6 6 6 1 CA EU 22 110 22 55 tonnes (110 tonnes combined
23 110 16.5 EU CA 6 6 6 2 CA EU 23 110 23 capacity)
• Bolt tightening torque: 250Nm (M24)
150Nm (M20)
Spanner size required: 36mm (M24)
30mm (M20)

46 Email: [email protected] www.modulift.com

 MOD 600XB/400

h The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
led span intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 600XB/400 has an
assembled span ranging from 2 metres to 26m in 1m increments.

Component list β =’Sling to Vertical’ angle

b
Part ref: Description
P10
P1 END UNIT WLL 200t P3 - P9
P2 DROP LINK WLL 200t
P3 5m STRUT
P9 P4 3m STRUT P1 P12
P5 4m STRUT Span P2
P11
P6 3m STRUT Fig. 1: Typical Spreader Assembly.
P7 2m STRUT
P8 1m STRUT
Larger shackle
P9 0.5m STRUT
P10 300t WIDE BODY SHACKLE
Smaller shackle
P11 200t WIDE BODY SHACKLE END UNIT
STRUT
DROP LINK SUB-ASSY
P12 M24x90 GRADE 10.9 HT BOLTS,
NUTS & WASHERS

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 600XB/400 - SYSTEM
/m /t sling STV = ‘SLING TO STV
/m /t sling Specification
Length / m VERTICAL’ ANGLE, ß BSA Length / m
• Rated at 400 tonnes SWL at 25m
2 285 1.0 EU EU 2 400 2 span
3 285 2.0 EU 1 EU 3 400 3
• ‘Sling to Vertical’ angle, ß, 45 degrees
4 285 2.5 EU 2 EU 4 400 4
or less
5 285 3.5 EU 3 EU 5 400 5
• End units and drop links are rated at
6 285 4.0 EU 3 1 EU 6 400 6
200 tonnes (400 tonnes combined
7 285 4.5 EU 3 2 EU 7 400 7
capacity)
8 285 5.5 EU 6 EU 8 400 8
• Bolt tightening torque: 250Nm
9 285 6.0 EU 6 1 EU 9 400 9
Spanner size required: 36mm
10 285 7.0 EU 6 2 EU 10 400 10
11 285 7.5 EU 6 3 EU 11 400 11
12 285 8.5 EU 3 6 1 EU 12 400 12
13 285 9.0 EU 3 6 2 EU 13 400 13
14 285 9.5 EU 6 6 EU 14 400 14
15 285 10.5 EU 6 6 1 EU 15 400 15
16 285 11.0 EU 6 6 2 EU 16 400 16
17 285 12.0 EU 6 6 3 EU 17 400 17
18 285 12.5 EU 1 6 6 3 EU 18 400 18
19 285 13.0 EU 2 6 6 3 EU 19 400 19
20 285 14.0 EU 6 6 6 EU 20 400 20
21 285 14.5 EU 6 6 6 1 EU 21 400 21
22 285 15.0 EU 6 6 6 2 EU 22 400 22
23 285 15.5 EU 6 6 6 3 EU 23 400 23
24 260 17.0 EU 1 6 6 6 3 EU 24 400 24
25 234 17.5 EU 2 6 6 6 3 EU 25 400 25
26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26

Email: [email protected] www.modulift.com 47

 MOD 600XB/600

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 600XB/600 has an
assembled span ranging from 2 metres to 26m in 1m increments.

Component list β =’Sling to Vertical’ angle

b
Part ref: Description
P10
P1 END UNIT WLL 300t P3 - P9
P2 DROP LINK WLL 300t
P3 5m STRUT
P9 P4 3m STRUT P1
P12
P11 Span P2
P5 4m STRUT
P6 3m STRUT Fig. 1: Typical Spreader Assembly.
P7 2m STRUT
P8 1m STRUT Larger shackle

P9 0.5m STRUT
Smaller shackle
P10 400t WIDE BODY SHACKLE END UNIT
STRUT SUB-ASSY
P11 300t WIDE BODY SHACKLE DROP LINK
P12 M24x90 GRADE 10.9 HT BOLTS,
NUTS & WASHERS

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m) ISA
Span SWL Min Top Mod 600XB/600 - SYSTEM
/m /t sling /m /t sling
Length / m
STV = ‘SLING TO STV

Length / m
Specification
VERTICAL’ ANGLE, ß BSA

• Rated at 600 tonnes SWL at 21m

2 415 1.0 EU EU 2 600 2 span
3 415 2.0 EU 1 EU 3 600 3
• ‘Sling to Vertical’ angle, ß, 45 degrees
4 415 2.5 EU 2 EU 4 600 4
or less
5 415 3.5 EU 3 EU 5 600 5
6 415 4.0 EU 3 1 EU 6 600 6
• End units and drop links are rated at
300 tonnes (600 tonnes combined
7 415 4.5 EU 3 2 EU 7 600 7
capacity)
8 415 5.5 EU 6 EU 8 600 8
9 415 6.0 EU 6 1 EU 9 600 9
• Bolt tightening torque: 250Nm
Spanner size required: 36mm
10 415 7.0 EU 6 2 EU 10 600 10
11 415 7.5 EU 6 3 EU 11 600 11
12 415 8.5 EU 3 6 1 EU 12 600 12
13 415 9.0 EU 3 6 2 EU 13 600 13
14 415 9.5 EU 6 6 EU 14 600 14
15 415 10.5 EU 6 6 1 EU 15 600 15
16 415 11.0 EU 6 6 2 EU 16 600 16
17 415 12.0 EU 6 6 3 EU 17 600 17
18 415 12.5 EU 1 6 6 3 EU 18 600 18
19 415 13.0 EU 2 6 6 3 EU 19 600 19
20 391 14.0 EU 6 6 6 EU 20 600 20
21 354 14.5 EU 6 6 6 1 EU 21 600 21
22 320 15.0 EU 6 6 6 2 EU 22 565 22
23 289 15.5 EU 6 6 6 3 EU 23 512 23
24 260 17.0 EU 1 6 6 6 3 EU 24 461 24
25 234 17.5 EU 2 6 6 6 3 EU 25 416 25
26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26

48 Email: [email protected] www.modulift.com

 MOD 600XB/800

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 600XB/800 has an
assembled span ranging from 2 metres to 26m in 1m increments.

Component list β =’Sling to Vertical’ angle

b
Part ref: Description
P10
P1 END UNIT WLL 400t P3 - P9
P2 DROP LINK WLL 400t
P3 6m STRUT
P9 P4 5m STRUT P1 P12
P11 Span P2
P5 4m STRUT
P6 3m STRUT
Fig. 1: Typical Spreader Assembly.
P7 2m STRUT Larger shackle

P8 1m STRUT
P9 0.5m STRUT
P10 500t WIDE BODY SHACKLE END UNIT Smaller shackle
STRUT
DROP LINK SUB-ASSY
P11 400t WIDE BODY SHACKLE
P12 M24x90 GRADE 10.9 HT BOLTS,
NUTS & WASHERS

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 600XB/800 - SYSTEM
/m /t sling /m /t sling
Length / m
STV = ‘SLING TO STV

Length / m
Specification
VERTICAL’ ANGLE, ß
BSA

• Rated at 800 tonnes SWL at 18m span

2 565 1.0 EU EU 2 800 2
3 565 2.0 EU 1 EU 3 800 3 • ‘Sling to Vertical’ angle, ß, 45 degrees
or less
4 565 2.5 EU 2 EU 4 800 4
5 565 3.5 EU 3 EU 5 800 5 • End units and drop links are rated at
6 565 4.0 EU 3 1 EU 6 800 6 400 tonnes (800 tonnes combined
capacity)
7 565 4.5 EU 3 2 EU 7 800 7
8 565 5.5 EU 6 EU 8 800 8 • Bolt tightening torque: 250Nm
9 565 6.0 EU 6 1 EU 9 800 9 Spanner size required: 36mm
10 565 7.0 EU 6 2 EU 10 800 10
11 565 7.5 EU 6 3 EU 11 800 11
12 565 8.5 EU 3 6 1 EU 12 800 12
13 565 9.0 EU 3 6 2 EU 13 800 13
14 565 9.5 EU 6 6 EU 14 800 14
15 565 10.5 EU 6 6 1 EU 15 800 15
16 559 11.0 EU 6 6 2 EU 16 800 16
17 514 12.0 EU 6 6 3 EU 17 800 17
18 469 12.5 EU 1 6 6 3 EU 18 800 18
19 427 13.0 EU 2 6 6 3 EU 19 749 19
20 391 14.0 EU 6 6 6 EU 20 688 20
21 354 14.5 EU 6 6 6 1 EU 21 623 21
22 320 15.5 EU 6 6 6 2 EU 22 565 22
23 289 16.0 EU 6 6 6 3 EU 23 512 23
24 260 17.0 EU 1 6 6 6 3 EU 24 461 24
25 234 17.5 EU 2 6 6 6 3 EU 25 416 25
26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26

Email: [email protected] www.modulift.com 49

 MOD 600XB/1000

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with
intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 600XB/1000 has an
assembled span ranging from 2 metres to 26m in 1m increments.

Component list β =’Sling to Vertical’ angle

b
Part ref: Description
P10
P1 END UNIT WLL 500t P3 - P9
P2 DROP LINK WLL 500t
P3 6m STRUT
P9
P4 5m STRUT P1 P12
Span P2
P5 4m STRUT P11
Fig. 1: Typical Spreader Assembly.
P6 3m STRUT
P7 2m STRUT
P8 1m STRUT Larger shackle

P9 0.5m STRUT
P10 600t WIDE BODY SHACKLE
END UNIT Smaller shackle
P11 500t WIDE BODY SHACKLE STRUT
DROP LINK SUB-ASSY
P12 M24x90 GRADE 10.9 HT BOLTS,
NUTS & WASHERS

Load v Span
45˚ STV Recommended Sling Angle Format
30˚ STV
Configuration
Span SWL Min Top EU - End Unit (1m)
ISA
Span SWL Min Top Mod 600XB/1000 - SYSTEM
/m /t sling /m /t sling
Length / m
STV = ‘SLING TO STV

Length / m
Specification
VERTICAL’ ANGLE, ß
BSA

• Rated at 1000 tonnes SWL at 15m

2 575 1.0 EU EU 2 1000 2
span
3 575 2.0 EU 1 EU 3 1000 3
• ‘Sling to Vertical’ angle, ß, 45 degrees
4 575 2.5 EU 2 EU 4 1000 4
or less
5 575 3.5 EU 3 EU 5 1000 5
6 575 4.0 EU 3 1 EU 6 1000 6 • End units and drop links are rated at
500 tonnes (1000 tonnes combined
7 575 4.5 EU 3 2 EU 7 1000 7
capacity)
8 575 5.5 EU 6 EU 8 1000 8
9 575 6.0 EU 6 1 EU 9 1000 9 • Bolt tightening torque: 250Nm
10 575 7.0 EU 6 2 EU 10 1000 10
Spanner size required: 36mm
11 575 7.5 EU 6 3 EU 11 1000 11
12 575 8.5 EU 3 6 1 EU 12 1000 12
13 575 9.0 EU 3 6 2 EU 13 1000 13
14 575 9.5 EU 6 6 EU 14 1000 14
15 575 10.5 EU 6 6 1 EU 15 1000 15
16 559 11.0 EU 6 6 2 EU 16 977 16
17 514 12.0 EU 6 6 3 EU 17 899 17
18 469 12.5 EU 1 6 6 3 EU 18 821 18
19 427 13.0 EU 2 6 6 3 EU 19 749 19
20 391 14.0 EU 6 6 6 EU 20 688 20
21 354 14.5 EU 6 6 6 1 EU 21 623 21
22 320 15.5 EU 6 6 6 2 EU 22 565 22
23 289 16.0 EU 6 6 6 3 EU 23 512 23
24 260 17.0 EU 1 6 6 6 3 EU 24 461 24
25 234 17.5 EU 2 6 6 6 3 EU 25 416 25
26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26

50 Email: [email protected] www.modulift.com

 MOD 800J/1000

The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop
Links, with intermediate struts that can be bolted into the assembly to achieve different spans. The MOD 800J/1000
has an assembled span ranging from 2 metres to 28m in 0.5m increments.

β =’Sling to Vertical’ angle

Span
Span
Fig. 1: Typical Spreader Assembly.

Larger shackle

END UNIT
STRUT Smaller shackle
SUB-ASSY
DROP LINK

Load v Span Component list

Recommended Sling Angle Format 30º STV Part ref: Description
Configuration. Span SWL Min Top
EU - End Unit (1m) P1 END UNIT - WLL 500t
ISA

/m /t sling
STV = ‘SLING to
Length / m
STV

VERTICAL’ ANGLE, β
BSA P2 DROP LINK - WLL 500t

EU EU 2 1000 1.5 P3 6.0m STRUT

EU 1 EU 3 1000 2.5 P4 5.0m STRUT
EU 2 EU 4 1000 3.5 P5 4.0m STRUT
EU 3 EU 5 1000 4.5 P6 3.0m STRUT
EU 3 1 EU 6 1000 5.5
P7 2.0m STRUT
EU 3 2 EU 7 1000 6.5
EU 6 EU 8 1000 7.5
P8 1.0m STRUT
EU 6 1 EU 9 1000 8.5 P9 0.5m STRUT
EU 6 2 EU 10 1000 9.5 P10 600t WIDE BODY SHACKLE
EU 6 3 EU 11 1000 10.5
P11 500t WIDE BODY SHACKJLE
EU 3 6 1 EU 12 1000 11.5
EU 3 6 2 EU 13 1000 12.5 P12 M24x100 Grade 10.9 HT BOLTS,
NUTS & WASHERS
EU 6 6 EU 14 1000 13.5
EU 6 6 1 EU 15 1000 14.5
EU 6 6 2 EU 16 1000 15.5 Mod 800J/1000 - SYSTEM
EU 6 6 3 EU 17 1000 16.5 Specification
EU 1 6 6 3 EU 18 1000 17.5
• Rated at 1000 tonnes SWL at 20m
EU 2 6 6 3 EU 19 1000 18.5
span
EU 6 6 6 EU 20 1000 19.5
EU 6 6 6 1 EU 21 944 20.5 • ‘Sling to Vertical’ angle, ß, 30 degrees
EU 6 6 6 2 EU 22 871 21.5 or less
EU 6 6 6 3 EU 23 802 22.5 • End units and drop links are rated at
EU 1 6 6 6 3 EU 24 734 23.5 500 tonnes (1000 tonnes combined
EU 2 6 6 6 3 EU 25 673 24.5 capacity)
EU 1 2 6 6 6 3 EU 26 612 25.5
EU 1 3 6 6 6 3 EU 27 556 26.5 • Bolt tightening torque: 250Nm
EU 2 3 6 6 6 3 EU 28 505 27.5 Spanner size required: 36mm

Email: [email protected] www.modulift.com 51

 CMOD Spreader Frame Range

Modulift Modular Spreader Frames work with

existing struts from our Modular Spreader
Beam range

Fig. 1: Example CMOD Modular Spreader Frame

Modulift, the market leaders in Spreader Beam design and manufacture, have extended their
modular offering, by launching the CMOD Modular Spreader Frame! A truly adaptable frame that
maintains its engineering principles as its configuration adapts. Designed with ease and economy
in mind - the CMOD is simple to set up, manoeuvre, and reconfigure to any size frame - allowing for
multiple uses and diverse application.

The CMOD is a modular frame utilising Corner Units which are compatible with our existing Spreader
Beam Struts and is modular in length and width. Every CMOD Spreader Frame consists of 4 x
Corner Units, with intermediate Struts that can be bolted into the assembly to achieve different
spans. Existing customers can adapt their Spreader Beam into a frame, by simply bolting on the
corresponding Corner Units and any additional Struts required.
Even the largest CMOD can be easily transported as the frame is broken down into modular parts,
saving the cost of specialist transportation.

System Specifications
The CMOD comes in the following sizes:
CMOD 6, CMOD 12, CMOD 24, CMOD 34, CMOD 50, CMOD 70 and CMOD 110
It spans from 0.5m/1’6”x 0.5m/1’6” to 16m/52’ x 16m/52’, whilst adapting to all rectangular shapes in
between. The systems will lift up to 140t*
* The system’s SWL will de-rate as the shape of the frame becomes “more rectangular”. Higher capacities and longer spans
in development.

52 Email: [email protected] www.modulift.com

 CMOD 6 Spreader Frame

The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts
that can be bolted into the assembly to achieve different spans. The CMOD 6 has an assembled span ranging from
0.5m by 0.5m to 2.5m by 2.5m and all spans inbetween.

Fig. 1 Typical CMOD Spreader Frame Assembly

β β = ‘Sling to Vertical’ Angle (STV)
P7

P1 P2 - P6 P9 P8
Span

STRUT

Assembled Frame: CORNER UNIT

Table 2 Component list

Part ref: Description
30° STV SWL = tonnes
2.5 8 P1 CORNER UNIT

P2 1000mm STRUT
2 8 8
P3 600mm STRUT
Span/m

m 1.5 8 8 8 P4 300mm STRUT

P5 200mm STRUT
1 8 8 8 6 P6 100mm STRUT

P7 8.5t SHACKLE
0.5 8 8 8 6 6
P8 6.5t SHACKLE

P9 M10X30, GRADE 8.8, HT BOLTS NUTS &

0.5 1 1.5 2 2.5 WASHERS

m
Span/m

2.5 45° STV SWL = tonnes 6

CMOD 6 - SYSTEM Specification
2 6 6 • Rated at a maximum of 8 tonnes
SWL
Span/m

1.5 6 6 6
• ‘Sling to Vertical’ angle, ß, no more
than 45 degrees
1 6 6 6 4
• Corner Units are rated at 2 tonnes
0.5 6 6 6 4 4 each (8t combined capacity)
• Bolt tightening torque: 60Nm
0.5 1 1.5 2 2.5 Spanner size required: 17mm
Span/m

Email: [email protected] www.modulift.com 53

 CMOD 12 Spreader Frame

The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts
that can be bolted into the assembly to achieve different spans. The CMOD 12 has an assembled span ranging from
0.5m by 0.5m to 4m by 4m and all spans inbetween.

Fig. 1 Typical CMOD Spreader Frame Assembly

β
β = ‘Sling to Vertical’ Angle (STV)

P7

P1 P2 - P6 P9 P8

STRUT Span

STRUT

Assembled Frame: CORNER UNIT

Table 2 Component list

Part ref: Description
4 30° STV SWL = tonnes 16
P1 CORNER UNIT
3.5 16 16
P2 1.5m STRUT
3 16 16 15
P3 1.0m STRUT
Span/m

2.5 16 16 15 14 P4 0.75m STRUT

2 16 16 16 14 13 P5 0.5m STRUT

1.5 16 16 16 16 14 12 P6 0.25m STRUT

1 16 16 16 16 16 14 12
P7 8.5t SHACKLE
P8 6.5t SHACKLE
0.5 16 16 16 16 16 16 14 12
P9 M12X35, GRADE 8.8, HT BOLTS
0.5 1 1.5 2 2.5 3 3.5 4 NUTS & WASHERS
Span/m

4 45° STV SWL = tonnes 9

3.5 9 9
CMOD 12 - SYSTEM Specification
• Rated at a maximum of 16 tonnes
3 9 9 8
SWL
Span/m

2.5 9 9 8 8
• Sling to Vertical Angle, β, no more
2 9 9 9 8 7
than 45 degrees
1.5 9 9 9 9 8 6
• Corner Units are rated at 4 tonnes
1 9 9 9 9 9 8 6 each (16t combined capacity)
0.5 9 9 9 9 9 9 8 6
• Bolt tightening torque: 90Nm
0.5 1 1.5 2 2.5 3 3.5 4 Spanner size required: 19mm
Span/m

54 Email: [email protected] www.modulift.com

 CMOD 24 Spreader Frame

The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts
that can be bolted into the assembly to achieve different spans. The CMOD 24 has an assembled span ranging from
1m by 1m to 6m by 6m and all spans inbetween.

Fig. 1 Typical CMOD Spreader Frame Assembly

β
β = ‘Sling to Vertical’ Angle (STV)
P5

P1 P2 - P4 P7 P6
Span

STRUT

Assembled Frame: CORNER UNIT

Table 2 Component list

Part ref: Description
6 30° STV SWL = tonnes 23
P1 CORNER UNIT
5 30 21 P2 2.0m STRUT
P3 1.0m STRUT
Span/m

4 30 24 19
P4 0.5m STRUT
3 30 30 24 18 P5 17t SHACKLE
P6 12t SHACKLE
2 30 30 30 24 17
P7 M20X50, GRADE 8.8, HT BOLTS NUTS
1 30 30 30 24 22 16 & WASHERS

1 2 3 4 5 6

Span/m

6 45° STV SWL = tonnes 13

CMOD 24 - SYSTEM Specification
5 17 12
• Rated at a maximum of 30 tonnes
Span/m

4 19 13 10 SWL

3 19 19 13 10
• ‘Sling to Vertical’ angle, ß, no more
than 45 degrees
2 19 19 17 13 9
• Corner Units are rated at 7.5 tonnes
1 19 19 19 13 12 9
each (30t combined capacity)
• Bolt tightening torque: 150Nm
1 2 3 4 5 6
Spanner size required: 30mm
Span/m

Email: [email protected] www.modulift.com 55

 CMOD 34 Spreader Frame

The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts
that can be bolted into the assembly to achieve different spans. The CMOD 34 has an assembled span ranging from
1m by 1m to 8m by 8m and all spans inbetween.

Fig. 1 Typical CMOD Spreader Frame Assembly

β
β = ‘Sling to Vertical’ Angle (STV)
P5

P1 P2 - P4 P7 P6
Span

STRUT

Assembled Frame: CORNER UNIT

Table 2 Component list

Part ref: Description
8 30° STV SWL = tonnes 24
P1 CORNER UNIT
7 32 23
P2 2.0m STRUT
6 40 31 22 P3 1.0m STRUT
5 40 40 28 20 P4 0.5m STRUT
Span/m

4 40 40 34 26 19 P5 25t SHACKLE
P6 17t SHACKLE
3 40 40 40 34 24 18
P7 M20X50, GRADE 8.8, HT BOLTS NUTS
2 40 40 40 40 32 23 17 & WASHERS
1 40 40 40 40 34 30 22 16

1 2 3 4 5 6 7 8

Span/m

8 45° STV SWL = tonnes 13

7 18 13 CMOD 34 - SYSTEM Specification

6 22 17 12 • Rated at a maximum of 40 tonnes
SWL
Span/m

5 27 22 16 11

4 27 27 19 15 10
• ‘Sling to Vertical’ angle, ß, no more
than 45 degrees
3 27 27 25 19 13 10
• Corner Units are rated at 10 tonnes
2 27 27 27 22 18 13 9
each (40t combined capacity)
1 27 27 27 27 19 17 12 9
• Bolt tightening torque: 150Nm
1 2 3 4 5 6 7 8 Spanner size required: 30mm
Span/m

56 Email: [email protected] www.modulift.com

 CMOD 50 Spreader Frame

The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts
that can be bolted into the assembly to achieve different spans. The CMOD 50 has an assembled span ranging from
1m by 1m to 11m by 11m and all spans inbetween.

β Fig. 1 Typical CMOD Spreader Frame Assembly

β = ‘Sling to Vertical’ Angle (STV)

P6

P1 P2 - P5 P8 P7
Span

STRUT

Assembled Frame: CORNER UNIT

Table 2 Component list

Part ref: Description
11 32
30° STV SWL = tonnes P1 CORNER UNIT
10 41 31
P2 4.0m STRUT
9 50 39 29
8 50 48 37 28 P3 2.0m STRUT
7 60 50 45 35 27 P4 1.0m STRUT
Span/m

6 60 60 50 43 33 26
P5 0.5m STRUT
5 60 60 60 50 40 32 25
P6 35t SHACKLE
4 60 60 60 50 49 38 31 24
3 60 60 60 60 50 47 37 30 23
P7 25t SHACKLE
2 60 60 60 60 60 50 45 36 29 23 P8 M20X65, GRADE 8.8, HT BOLTS
1 60 60 60 60 60 60 50 44 35 28 22 NUTS & WASHERS
1 2 3 4 5 6 7 8 9 10 11

Span/m

11 18
45° STV SWL = tonnes
10 23 17
CMOD 50 - SYSTEM Specification
9 28 21 16
8 28 27 20 15
• Rated at a maximum of 60 tonnes SWL
7 34 28 25 19 14 • ‘Sling to Vertical’ angle, ß, no more
Span/m

6 40 34 28 24 18 14 than 45 degrees
5 40 40 34 28 23 17 13
4 50 40 40 28 28 21 17 13
• Corner Units are rated at 15 tonnes
3 50 50 40 40 28 26 21 16 12
each (60t combined capacity)
2 50 50 50 40 34 28 25 20 16 12 • Bolt tightening torque: 150Nm
1 50 50 50 50 40 34 28 25 20 15 12
Spanner size required: 30mm
1 2 3 4 5 6 7 8 9 10 11

Span/m

Email: [email protected] www.modulift.com 57

 CMOD 70 Spreader Frame

The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts
that can be bolted into the assembly to achieve different spans. The CMOD 70 has an assembled span ranging from
1m by 1m to 12m by 12m and all spans inbetween.

Fig. 1 Typical CMOD Spreader Frame Assembly

β
β = ‘Sling to Vertical’ Angle (STV)
P6

P1 P2 - P5 P8 P7
Span

STRUT

Assembled Frame: CORNER UNIT

Table 2 Component list

Part ref: Description
12 63
30° STV SWL = tonnes P1 CORNER UNIT
11 70 60
10 80 70 58 P2 4.0m STRUT
9 80 80 70 55 P3 2.0m STRUT
8 80 80 80 67 53
P4 1.0m STRUT
7 80 80 80 70 65 51
P5 0.5m STRUT
Span/m

6 80 80 80 70 60 62 49
5 80 80 80 80 70 60 60 47
P6 42.5t SHACKLE
4 80 80 80 80 80 70 60 58 46
3 80 80 80 80 80 80 70 60 56 45
P7 35t SHACKLE
2 80 80 80 80 80 80 70 70 60 55 44
P8 M20X65, GRADE 8.8, HT BOLTS NUTS
1 80 80 80 80 80 80 80 70 70 60 54 44 & WASHERS
1 2 3 4 5 6 7 8 9 10 11 12

Span/m

12 36
45° STV SWL = tonnes
11 40 34
10 40 40 33
CMOD 70 - SYSTEM Specification
9 46 40 40 31 • Rated at a maximum of 80 tonnes
8 57 46 40 38 30 SWL
7 60 57 46 40 37 29
Span/m

6 60 60 57 40 34 35 28 • ‘Sling to Vertical’ angle, ß, no more

5 60 60 60 50 40 34 34 27 than 45 degrees
4 60 60 60 60 50 40 34 33 26
3 60 60 60 60 60 50 40 34 32 26 • Corner Units are rated at 20 tonnes
2 60 60 60 60 60 60 50 40 34 31 25 each (80t combined capacity)
1 60 60 60 60 60 60 60 50 40 34 31 24
1 2 3 4 5 6 7 8 9 10 11 12
• Bolt tightening torque: 150Nm
Span/m
Spanner size required: 30mm

58 Email: [email protected] www.modulift.com

 CMOD & Beyond

System Benefits
• Cheaper and easier to transport than a fixed system
• Easy to set up, handle and manoeuvre
• Re-configure the frame to any size to allow for multiple uses
• The corner plate has a bow (like the shackle). This means that a reversed Shackle can contact the
plate ‘bow to bow’ allowing it to easily rotate to suit any angle of sling and setup of frame without
de-rating the Shackle

Design Strengths
The plate is made of high strength carbon steel and is specifically designed to withstand any bending,
and transfers the compression to the strut in an almost purely axial form. The system was designed to
BS EN 13155 – Non Fixed Lifting Load Attachments and the method of Shackle connection has been
approved by Van Beest.

CMOD T-pieces
Elaborating on this popular concept Modulift has now developed
a T-Piece to work in conjunction with the CMOD. This allows the
frame to become a 6-point lift, (8-point,10-point and so forth
on request) adding yet another dimension to your
Modulift equipment. Spans of up to 40m x 16m and capacities
of up to 200t are available as standard.

Email: [email protected] www.modulift.com 59

 Lattice Spreader Beams

The Modulift Lattice System (MLS) is a light-weight modular spreader suitable for long, light loads, and has been specially
developed to suit roofing sheets.
Maximum spans from 6m up to 42m in 3m increments are achievable using this system. Lower support slings must be
attached to the frames every 2m to ensure a uniformly distributed load.

Components

TYPE 1:
100KG

3m 1m

TYPE 2: CROSS BAR: 7.5KG

137KG

3m

TYPE 3:
17.5 KG
FRAMES CONNECTION PIN

SPREADER SYSTEM Specification

• Rated at a maximum of 3 tonnes
WLL(Upto 24m Span)
• ‘Sling to Vertical’ angle, ß, 45 degrees or
less
• Lifting points: Slings can be connected to
weld eyes on ends of 1m span cross bars,
or to weld eyes on underside of frames.

Assembly
Max. 6.5t shackle

Max. 3.25t Connection

shackle Pins - 2 per
Cross Beam

CONNECTION JOINTS - TYPICAL CROSS BAR

USE 4 no. CONNECTION
PINS PER JOINT. CONNECTION

60 Email: [email protected] www.modulift.com

 Lattice Spreader Beam 6 - 24m Span

Configuration
SPREADER Configuration No. of
Crossbeams
6m 2 3 2 3 or 4
9m 2 1 3 2 6
12m 1 2 3 2 1 7
15m 1 2 1 3 2 1 8
18m 1 2 1 3 1 2 1 10
21m 1 2 1 1 3 1 2 1 11
24m 1 2 1 1 3 1 1 2 1 13
1 = Type 1 Frame Maximum 1.5m overhang of
2 = Type 2 Frame roofing sheet per end
3 = Type 3 Frame

Lifting Points/Load Connection Points

= connection point for

cross bar, and/or con- 318 KG 6m Spreader: LC =8; CB = 6 PINS LC = Lattice Connections
nection point for sling to CB = Cross Beams
weld eye. LC =8; CB = 8 PINS
327 KG 6m Spreader:
Alternative

444 KG 9m Spreader: LC =12; CB = 12 PINS

552 KG 12m Spreader: LC =16; CB = 14 PINS

661 KG 15m Spreader: LC =20; CB = 16 PINS

778 KG
18m Spreader: LC =24; CB = 20
PINS
887 KG
21m
Spreader: LC =28; CB = 22 PINS

1005 KG LC =32; CB = 26 PINS

24m Spreader:

Top Sling Minimum Length

6m Spreader : 2.2m These sling lengths are 45º
9m Spreader: 4.3m essential to ensure the Sling
12m Spreader: 2.2m to Vertical Angle is 45 degrees
15m Spreader: 4.3m or less.
18m Spreader: 6.5m
21m Spreader: 8.7m
24m Spreader: 10.8m

Email: [email protected] www.modulift.com 59

 Lattice Spreader Beam - 27m Span

The Modulift Lattice System (MLS) is a light-weight modular spreader suitable for long, light loads, and has been
specially developed to suit roofing sheets.
Maximum spans from 6m up to 42m in 3m increments are achievable using this system. Lower support slings must be
attached to the frames every 2m to ensure a uniformly distributed load.

Components

TYPE 1:
100KG

3m 1m

TYPE 2: CROSS BAR: 7.5KG

137KG

3m

TYPE 3:
17.5 KG
FRAMES CONNECTION PIN

Assembled Lattice Spreader Beam

Total weight = 1121kg

Top Sling Min Length = 13m

SPREADER Configuration No. of

Crossbeams LATTICE SPREADER Specification
27m 1 2 1 1 1 3 1 1 2 1 15 • Rated at a maximum of 2 tonnes WLL -
1 = Type 1 Frame x 7 Maximum 1.5m overhang of Uniformly Distributed Load only (Up to
2 = Type 2 Frame x 2 roofing sheet per end 27m span)
3 = Type 3 Frame x 1
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less

Assembly • Lifting points: Slings can be connected

to weld eyes on ends of 1m span cross
Max. 6.5t shackle
bars, or to weld eyes on underside of
Max. 3.25t
CONNECTION PINS -
2 PER CROSS BEAM
frames
shackle

CONNECTION JOINTS -
• The sling arrangement must not be
USE 4 no. CONNECTION
PINS PER JOINT. TYPICAL CROSS BAR modified without Modulift’s
CONNECTION
written approval

62 Email: [email protected] www.modulift.com

 Lattice Spreader Beam - 30m Span

The Modulift Lattice System (MLS) is a light-weight modular spreader suitable for long, light loads, and has been
specially developed to suit roofing sheets.
Maximum spans from 6m up to 42m in 3m increments are achievable using this system. Lower support slings must be
attached to the frames every 2m to ensure a uniformly distributed load.

Components

TYPE 1:
100KG

3m 1m

TYPE 2: CROSS BAR: 7.5KG

137KG

3m

TYPE 3:
17.5 KG
FRAMES CONNECTION PIN

Assembled Lattice Spreader Beam

Centred Sling Support Wire Rope

Chain Block

Use round/welding
sling to connect
Total weight = 1231kg chain block and
Top Sling Min Length = 15m Spreader Beam

SPREADER Configuration No. of

Crossbeams LATTICE SPREADER Specification
30m 1 2 1 1 1 3 1 1 1 2 1 16 • Rated at a maximum of 2 tonnes WLL -
1 = Type 1 Frame x 8 Maximum 1.5m overhang of Uniformly Distributed Load only (Up to
2 = Type 2 Frame x 2 roofing sheet per end 30m span)
3 = Type 3 Frame x 1
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
• Lifting points: Slings can be connected
Assembly to weld eyes on ends of 1m span cross
Max. 6.5t shackle
bars, or to weld eyes on underside of
Max. 3.25t
CONNECTION PINS -
2 PER CROSS BEAM frames
shackle

CONNECTION JOINTS -
• The sling arrangement must not be
USE 4 no. CONNECTION
PINS PER JOINT. TYPICAL CROSS BAR modified without Modulift’s
CONNECTION
written approval

Email: [email protected] www.modulift.com 63

 Lattice Spreader Beam - 33m Span

The Modulift Lattice System (MLS) is a light-weight modular spreader suitable for long, light loads, and has been
specially developed to suit roofing sheets.
Maximum spans from 6m up to 42m in 3m increments are achievable using this system. Lower support slings must be
attached to the frames every 2m to ensure a uniformly distributed load.

Components

TYPE 1:
100KG

3m 1m

TYPE 2: CROSS BAR: 7.5KG

137KG

3m

TYPE 3:
17.5 KG
FRAMES CONNECTION PIN

Assembled Lattice Spreader Beam

Centred Sling Support Wire Rope

Chain Block

Use round/welding
Total weight = 1347kg sling to connect
chain block and
Top Sling Min Length = 17.5m Spreader Beam

SPREADER Configuration No. of

Crossbeams LATTICE SPREADER Specification
33m 1 2 1 1 1 1 3 1 1 1 2 1 18 • Rated at a maximum of 2 tonnes WLL -
1 = Type 1 Frame x 9 Maximum 1.5m overhang of Uniformly Distributed Load only (Up to
2 = Type 2 Frame x 2 roofing sheet per end 33m span)
3 = Type 3 Frame x 1
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
• Lifting points: Slings can be connected
Assembly to weld eyes on ends of 1m span cross
Max. 6.5t shackle
bars, or to weld eyes on underside of
CONNECTION PINS -
frames
Max. 3.25t 2 PER CROSS BEAM
shackle
• The sling arrangement must not be
CONNECTION JOINTS -
USE 4 no. CONNECTION
modified without Modulift’s
TYPICAL CROSS BAR
PINS PER JOINT.
CONNECTION written approval

64 Email: [email protected] www.modulift.com

 Lattice Spreader Beam - 36m Span

The Modulift Lattice System (MLS) is a light-weight modular spreader suitable for long, light loads, and has been
specially developed to suit roofing sheets.
Maximum spans from 6m up to 42m in 3m increments are achievable using this system. Lower support slings can be
attached to the frames every 2m to ensure a uniformly distributed load.

Components

TYPE 1:
100KG

3m 1m

TYPE 2: CROSS BAR: 7.5KG

137KG

3m

TYPE 3:
17.5 KG
FRAMES CONNECTION PIN

Assembled Lattice Spreader Beam

22m 18m 13m 18m 22m

2.6m

Total weight = 1604kg

Top Sling Min Length = As shown above

SPREADER Configuration No. of Cross-

beams LATTICE SPREADER Specification
36m 2 1 2 1 1 2 3 2 1 1 2 1 2 19 • Rated at a maximum of 2 tonnes WLL -
1 = Type 1 Frame x 6 Maximum 1.5m overhang of Uniformly Distributed Load only (Up to
2 = Type 2 Frame x 6 roofing sheet per end 36m span)
3 = Type 3 Frame x 1
• ‘Sling to Vertical’ angle, ß, 45 degrees
or less
• Lifting points: Slings can be connected
Assembly to weld eyes on ends of 1m span cross
Max. 6.5t shackle bars, or to weld eyes on underside of
CONNECTION PINS - frames
Max. 3.25t 2 PER CROSS BEAM
shackle
• The sling arrangement must not be
CONNECTION JOINTS -
USE 4 no. CONNECTION modified without Modulift’s
PINS PER JOINT. TYPICAL CROSS BAR
CONNECTION written approval

Email: [email protected] www.modulift.com 65

 Lattice Spreader Beam - 42m Span

The Modulift Lattice System (MLS) is a light-weight modular spreader suitable for long, light loads, and has been
specially developed to suit roofing sheets.
Maximum spans from 6m up to 42m in 3m increments are achievable using this system. Lower support slings must be
attached to the frames every 2m to ensure a uniformly distributed load.

Component list

TYPE 1:
100KG

3m 1m

TYPE 2: CROSS BAR: 7.5KG

137KG

3m

TYPE 3:
17.5 KG
FRAMES CONNECTION PIN

Assembled Lattice Spreader Beam

37m 33.5m 29m 33.5m 37m

3m

Total weight = 1822kg

Top Sling Min Length = As shown above

SPREADER Configuration No. of

Crossbeams LATTICE SPREADER Specification
42m 2 1 1 2 1 1 2 3 2 1 1 2 1 1 2 23 • Rated at a maximum of 1 tonne WLL -
1 = Type 1 Frame x 8 Maximum 1.5m overhang of Uniformly Distributed Load only (Up to
2 = Type 2 Frame x 6 roofing sheet per end 42m span)
3 = Type 3 Frame x 1
• Lifting points: Slings can be connected
to weld eyes on ends of 1m span cross
Assembly bars, or to weld eyes on underside of
Max. 6.5t shackle frames
Max. 3.25t
CONNECTION PINS -
2 PER CROSS BEAM • The sling arrangement must not be
shackle
modified without Modulift’s
CONNECTION JOINTS -
USE 4 no. CONNECTION
written approval.
PINS PER JOINT. TYPICAL CROSS BAR
CONNECTION

66 Email: [email protected] www.modulift.com

Where To Buy & Contacts

Modulift is here for you every step of the way ... For Marketing Enquiries
UK Head Office Contact details: Marketing Manager - Wendy Armstrong
[email protected]
Managing Director – Sarah Spivey
[email protected]
Marketing Executive– Sophie Briggs
[email protected]
Operations Director – Sue Caples
[email protected]
For Accounts & Order Enquiries
Sales Orders Co-ordinator – Paul Savage
Production & QA Manager – Simon Cranny
[email protected]
[email protected]

For Production & Administrational Enquiries

For Distributor Operations/Training
or to become a Distributor Production Administrator - Lydia Davies
[email protected]
International Business Development Manager
Malcolm Peacock
[email protected] Tel: +44 (0) 1202 621511
(Based in UAE - Tel: +971 56 2199 663 00 11 44 1202 621511 (USA & Canada)
Fax: +44 (0) 1202 632811
For Sales Enquiries
Sales Executive – Chris Schwab
[email protected]

Email: [email protected] www.modulift.com 67

 Working between the hook and the load

CAT-UK-14
Email: [email protected] www.modulift.com