THE MODUS SYSTEM

IVECO

SECOND PART

dr
af
t

THE DIAGNOSIS SYSTEM

7. CONNECTION DIAGRAMS AREA

 t
af
dr
SECOND PART

7. CONNECTION DIAGRAMS AREA

7.1 ELECTRICAL FUNCTIONS ..........................................................................................2

The Select Electrical Functions screen page .............................................2
Keys and icons of the Electrical Functions environment ....................3
Electrical function analysis and measurement procedure ..................3
Error conditions .........................................................................................................4

7.2 COMPONENTS SHEET ................................................................................................4

7.3 MULTIMETER SHEET....................................................................................................5

How to make a measurement with the multimeter ............................6

7.4 ECU SHEET .......................................................................................................................7

dr
af
t
SECOND PART 7 - CONNECTION DIAGRAMS AREA

7. CONNECTION DIAGRAMS AREA

Selection of the CONTROL UNIT AREA key in the list of diagnosis options
permits entry to the analysis session, organized in three sections:
1. electrical functions – measurement environment in which
the connection diagrams of the systems controlled by an
electronic control unit are displayed. Information regarding
the components of the connection diagram is available. To
use the Multimeter environment from the MODUS Station,
to make electrical measurements, this must be connected
via network with the IWT
2. electronic systems – diagnosis activities
3. auxiliary functions – 2nd level programming activities (modifi-
cation of configurations) and forms.

KEY 7.1

a. AUXILIARY FUNCTIONS sheet

b. ELECTRONIC SYSTEMS sheet
a
dr
c. ELECTRICAL FUNCTIONS
b
sheet
af
d. IDEOGRAM

c e. SYSTEM SELECTION active

e
area
t
d
f. BASIC CONNECTION
DIAGRAMS AREA key
g. SERVICES CONNECTION
DIAGRAMS AREA key

Fig. 7.1 – Select Electrical Functions screen page.

The system positions automatically on the Select Electrical Functions The types of system available
screen page, but each of the three sections can be accessed selec- depend on the type of vehicle
ting the matching sheet. under test.

128
SECOND PART 7 - CONNECTION DIADRAMS AREA

7.1 ELECTRICAL FUNCTIONS

Once the BASIC CONNECTION DIAGRAMS key or the SERVICES CON-

NECTION DIAGRAM, key has been selected, the MODUS system posi-
tions on the Select Electrical Functions screen page.
Refer to part I - chapter 3 of the If the MODUS station has been connected to an IWT, or if an IWT
manual for the MODUS-IWT con- is used in independent mode, this screen page permits access to an
nection. information and measurement environment for the electrical com-
ponents of the vehicle under test.
WARNING correct diagnosis of an electronic system must include an analysis of
the connection diagram where the control unit is connected in
order to avoid incorrect operations on the electronic system.

The Select Electrical Functions screen page

This screen page lists the electrical functions available for the vehicle
under test which are displayed in the form of ideograms (ref. fig. 7.1).
When you select the IDEOGRAM required, the system accesses the
Connection Diagram environment and positions automatically on the
MULTIMETER sheet.
In the Connection Diagram environment, for each electrical function con-
cerned, system resources can be accessed selecting each of the following
sheets (ref. fig. 7.3):
dr
1. ECU (ELECTRONIC CONTROL UNIT) sheet
2. MULTIMETER sheet
af
3. COMPONENTS sheet
Each sheet displays the connection diagram of the function selected.
The CONNECTION DIAGRAM is a selectable active area: if necessary
t
you can scroll the diagram selecting it with one finger and dragging
your finger n the monitor. A yellow hand is displayed on the connec-
tion diagram when the drag function of the diagram is active.

129
SECOND PART 7 - CONNECTION DIAGRAMS AREA

Keys and icons of the Electrical Functions environment KEY 7.2

a. FULL SCREEN key: displays the

connection diagram on the
a entire screen
b. VIN – key: displays the
b connection diagram for the
previous VINs
c c. VIN+ key: displays the
connection diagram for the
d next VINs
d. MULTIMETER/ COMPONENT TEST
e
ENVIRONMENT key

f e. PRINT key
f. key 1:1: displays the connection
g diagram in scale 1:1
g. ENLARGE key: enlarges the point
h selected
h. ENLARGE AREA key: enlarges the
area selected
Fig. 7.2 – Electrical Functions environment: keys and icons of the toolbar.
dr
Electrical function analysis and measurement procedure
To star t an analysis of the electrical function required, it is advi-
af
sable to carr y out the following procedure:
– position on the Diagnosis Options Selection screen page
t
(ref. fig. 3.1)
– select the BASIC CONNECTION DIAGRAMS AREA or SERVICES
CONNECTION DIAGRAMS AREA key
– select the ELECTRICAL FUNCTIONS sheet, if this is not
displayed automatically (ref. fig. 7.1)
– select the IDEOGRAM corresponding to the electronic func-
tion required in the SELECT ELECTRICAL FUNCTION active area
the system positions on the MULTIMETER sheet of the Electrical Fun-
ctions environment (ref. fig. 7.4) and displays the connection dia-
gram of the function selected

– select the COMPONENTS sheet to identify a component in

the connection diagram and, if necessary, display its cha-
racteristics and position (ref. fig. 7.3)

130
SECOND PART 7 - CONNECTION DIADRAMS AREA

– select the MULTIMETER sheet and select the component on

which the measurement is to be made in the COMPONENT
LIST active area

selection is also possible from the COMPONENTS sheet, COM-

PONENT LIST active area (ref. fig. 5.3)

– select the MEASUREMENT LINE L1 active area if this is not

selected (ref. fig. 7.4)
– in the MEASUREMENT POINTS LIST active area, select the mea-
surement required to combine with line L1
– repeat the procedure to associate line L2 to the measure-
ment point required
– select the MULTIMETER key to start the measurement
the system displays the correct connection method and proposes
a multimeter area from which the type of measurement can be
selected and the measurement made

Error conditions
If the software connection exists between the MODUS station and
IWT but the physical connection has not been made, only consulta-
tion of the connection diagrams is possible.
It is not possible therefore to make the measurement if the
dr
MODUS station is not connected to the IWT.
af
t

131
SECOND PART 7 - CONNECTION DIAGRAMS AREA

7.2 COMPONENTS SHEET

Displays the list of codes of the components in the connection dia-

gram of the function selected and related information in the Compo-
nents screen page.
The list is a selectable active area.
You can request information about each component of the list:
– select the component concerned
– select the COMPONENTS POSITION key
The figure of the component and its position on the vehicle are
displayed in a new screen page: select the TICK key to return to the
Components screen page.
Additional information about the component can be obtained
displaying its characteristics and internal diagram:
– select the COMPONENT INFO key
– select the DIAGRAM key (which has replaced the COMPO-
NENT INFO key) to return to display of the connection dia-
gram

KEY 7.3
a
dr
a. component name
b e
b. VIN code
f c. INFO active area VEHICLE
af
c g SELECTED

d. COMPONENT POSITION key

t
e. COMPONENT INFO key
f. COMPONENT LISY active area
d
g. CONNECTION DIAGRAM
active area

Fig. 7.3 – Components screen page.

The MULTIMETER sheet or the ECU sheet can be selected in order to

access the corresponding environments.

132
SECOND PART 7 - CONNECTION DIADRAMS AREA

7.3 MULTIMETER SHEET

An area of measurement is proposed in the Multimeter screen page;

the information and instruments required to make the measure-
ment are displayed:
– the connection diagram of the function under test
– the list of codes of the IVECO components indicated in the
connection diagram
– the list of measurement points for each component
– measurement assistance functions
The connection diagrams and lists are always selectable active areas.
WARNING The set of measurement assistance functions is active only if (ref.
fig. 7.4):
1. an IWT is used in stand-alone mode
2. the MODUS station is connected to an IWT

KEY 7.4
f
a. COMPONENTS sheet g

b. MULTIMETER sheet a
h
c. ECU sheet b
dr
d. MULTIMETER key c

e. TYPEOF CONNECTION key d

af
f. LINE SELECTION key (direct
access)
t
g. MEASUREMENT LINES L1 and L2 e i
active area
h. COMPONENT LIST and
MEASUREMENT POINT LIST
active areas
i. CONNECTION DIAGRAM active
area
Fig. 7.4 – Multimeter screen page.

133
SECOND PART 7 - CONNECTION DIAGRAMS AREA

Tab. 7.1 – Multimeter Screen Page: MEASUREMENT POINT TYPE keys. The
display of the measurement points can be restricted to those required
selecting the matching key

KEY DESCRIPTION KEY DESCRIPTION

measurement
points for bulk-head
components and measurment points
connections

UCI measurement
points

How to make a measurement with the multimeter

To start a measurement:
– identify the component(s) on which the measurement is to
be made
– select the component(s) in the COMPONENTS LIST active area
– select the MEASUREMENT LINE L1 active area
dr
– select the measurement point to be associated to line L1 in
the MEASUREMENT POINTS active area
af
– repeat the procedure to associate the L2 second measure-
ment line
– select the MULTIMETER key to start the measurement.
t
The system indicates the connection methods to make the measu-
rement and proposes the measurement environment.
The COMPONENTS sheet or the ECU sheet can be selected in order
to access the matching environments.

134
SECOND PART 7 - CONNECTION DIADRAMS AREA

7.4 ECU SHEET

The screen page also provides the following important information:

– the name of the function under test, indicated in the title of the
screen page
– the VIN code of the vehicle under test, indicated to the side
of the title
– the list of electronic control units present in the diagram

KEY 7.5 a
b
a. system name
c
b. the VIN code of the vehicle
under test
c. CONTROL UNIT keys
d. CONNECTION DIAGRAM
active area d
dr
Fig. 7.5 – ECU screen page
af
The ECU screen page (ref. fig. 7.5) includes the list of electronic con-
trol units present in the diagram in that different types of control
t
units (Bosch, Wabco, etc.) may be available for the same system.
From this level, select the CONTROL UNIT key to start the diagnosis
session of the control unit concerned.
The MULTIMETER sheet or the COMPONENTS sheet can be selected in
order to access the matching environments.

135