Lessson 5: Pressure Vessels and Stress Concentration

Download as pdf or txt
Download as pdf or txt
You are on page 1of 9

LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

5.1 Thin – Walled Pressure Vessels

A pressure vessel is a container holding a fluid (liquid or gas) under


pressure. Examples include carbonated beverage bottles, propane
tanks, and water mains. Drain pipes are not pressure vessels
because they are open to the atmosphere.

In a small pressure vessel such as a horizontal


pipe, we can ignore the effects of gravity on the
fluid. In the 17th century, French mathematician
and physicist Blaise Pascal discovered that
internal fluid pressure pushes equally against
the walls of the pipe in all directions, provided
the fluid is not moving. The SI pressure and
stress unit, the pascal (Pa), is named after Pascal
because of his work with fluid pressure. The
symbol for pressure is lower-case p, not to be
confused with upper-case P used for point loads.

If the thickness of the wall is less than 10% of the internal radius of the pipe or tank, then the
pressure vessel is described as a thin-walled pressure vessel. Because the wall is thin, the
stress in the wall is nearly the same on the inside and outside surfaces of the wall. (Thick-
walled pressure vessels have a higher stress on the inner surface than on the outer surface,
so cracks form from the inside out.)

Imagine cutting a thin-walled pipe lengthwise through the pressurized fluid and the pipe
wall: the force exerted by the fluid must equal the force exerted by the pipe walls (sum of the
forces equals zero). The force exerted by the fluid is 𝑝 ∙ 𝐴 = 𝑝𝑑𝑖 𝐿 where 𝑑𝑖 is the inside
diameter of the pipe, and L is the length of the pipe. The stress in the walls of the pipe is equal
to the fluid force divided by the cross-sectional area of the pipe wall. This cross-section of
one wall is the thickness of the pipe, t, times its length. Since there are two walls, the total
cross-sectional area of the wall is 2t L. The stress is around the circumference, also called the
𝑝𝑑 𝐿 𝑝𝑑
hoop direction, so 𝜎ℎ𝑜𝑜𝑝 = 2𝑡𝐿𝑖 = 2𝑡𝑖 . Hoop stress is independent of the length of the pipe.

5.1.1 Example #1
A pipe with a 15 in. outside diameter and a 14 in. inside diameter carries pressurized water at
110 psi. What is the hoop stress?
Given:
Pipe outside diameter, 𝑑𝑜 = 14 𝑖𝑛.
Pressure, 𝑝 = 110 𝑝𝑠𝑖

Required:
Hoop stress, 𝜎ℎ𝑜𝑜𝑝

1
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

Solution:
First, calculate the wall thickness, t. From the diagram, see that 𝑑𝑜 = 𝑑𝑖 + 2𝑡,

Therefore,
𝑑𝑜 − 𝑑𝑖 15 𝑖𝑛. −14 𝑖𝑛.
𝑡= = = 0.5 𝑖𝑛
2 2
Next, check if the pipe is thin-walled. The ratio of the pipe wall thickness to the internal radius is
𝑡 0.5 𝑖𝑛.
= = 0.071 < 0.10
𝑟𝑖 1
(14 𝑖𝑛. )
2
so the pipe is thin-walled.

Hoop stress:
𝑝𝑑𝑖 100 𝑝𝑠𝑖 ∙ 14 𝑖𝑛.
𝜎ℎ𝑜𝑜𝑝 = = = 1,540 𝑝𝑠𝑖
2𝑡 2(0.5 𝑖𝑛. )

What if the pipe is capped? If the cap were loose,


pressure would push the cap off the end. If the cap is
firmly attached to the pipe, then a stress develops along
the length of the pipe to resist pressure on the cap.
Imagine cutting the pipe and pressurized fluid
transversely. The force exerted by the fluid equals the
force along the length of the pipe walls. Pressure acts on
𝜋
a circular area of fluid, so the force exerted by the fluid is 𝑃𝑓𝑙𝑢𝑖𝑑 = 𝑝 ∙ 𝐴 = 𝑝 4 𝑑𝑖 2 . The cross-
𝜋 𝜋 𝜋
sectional area of the pipe wall 𝐴 = 4 𝑑𝑜 2 − 4 𝑑𝑖 2 = 4 (𝑑𝑜 2 − 𝑑𝑖 2 ) We can estimate the cross-
sectional area of a thin-walled pipe pretty closely by multiplying the wall thickness by the
𝑃𝑓𝑙𝑢𝑖𝑑 𝑝𝜋𝑑𝑖 2
circumference, so 𝐴 ≈ 𝜋𝑑𝑖 𝑡. The stress along the length of the pipe is 𝜎𝑙𝑜𝑛𝑔 = = .
𝐴𝑝𝑖𝑝𝑒 4𝜋𝑑𝑖 𝑡
𝑝𝑑𝑖
Simplify by canceling π and one of the diameters: 𝜎𝑙𝑜𝑛𝑔 = .
4𝑡

In a thin-walled pipe, hoop stress


is twice as large as longitudinal
stress. If the pressure in a pipe
exceeds the strength of the
material, then the pipe will split
along its length (perpendicular to
the hoop direction).

Does the shape of the cap affect the longitudinal stress in the pipe? No, because only the
cross-sectional area of the pipe matters. Typically, pressure vessels have concave or convex
domes, because flat caps tend to deflect under pressure, but the shape has no effect on
longitudinal stress in the pipe walls.

2
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

A welded steel outdoor propane tank


typically consists of a tube with two
convex hemispherical caps (right). Hoop
stress controls the design in the tube
portion. Where the caps are welded to the
tubes, longitudinal stress controls the
design. If the steel is all the same thickness
(and the welds are perfect), then the tank
will fail in the tube section because hoop
stress is twice the longitudinal stress. A
spherical tank (far right) only has longitudinal stress, so it can handle twice the pressure of
a tubular tank. Think of a spherical tank as two hemispheres welded together; the weld
prevents the two halves from separating.
𝑝𝑑𝑖
In conclusion, if you have a pipe or a tubular tank, use 𝜎ℎ𝑜𝑜𝑝 = . If you have a spherical
2𝑡
𝑝𝑑𝑖
tank, use 𝜎𝑙𝑜𝑛𝑔 = 4𝑡
. The ASME Boiler Code recommends using an allowable stress
1 2
𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 = 𝜎𝑈𝑇𝑆 or 𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 = 𝜎𝑌𝑆 .
4 3

5.1.2 Example #2
What is the minimum thickness of a spherical steel tank if the diameter is 10 feet, internal
pressure is 600 psi, the tensile strength of the steel is 65ksi, and the yield strength of the
steel is 30 ksi?

Given:
Pipe inside diameter, 𝑑𝑖 = 10 𝑓𝑡. = 120 𝑖𝑛.
Pressure, 𝑝 = 600 𝑝𝑠𝑖
Tensile strength of steel, 𝜎𝑈𝑇𝑆 = 65 𝑘𝑠𝑖 = 65000 𝑝𝑠𝑖
Yield strength of steel, 𝜎𝑌𝑆 = 30 𝑘𝑠𝑖 = 30000 𝑝𝑠𝑖

Required:
Minimum thickness of the tank, t

Solution:
First, calculate the allowable stress. Next, rewrite the stress equation for longitudinal
stress (because this is a sphere, not a pipe) to solve for wall thickness.

Based on tensile strength,


1 65000 𝑝𝑠𝑖
𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 = 𝜎𝑈𝑇𝑆 = = 16250 𝑝𝑠𝑖
4 4
Based on yield strength,
2 2(30000 𝑘𝑠𝑖 )
𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 = 𝜎𝑌𝑆 = = 20000 𝑘𝑠𝑖
3 3
Therefore use 16250 psi because it is the smaller number.

3
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

Longitudinal stress:
𝑝𝑑𝑖
𝜎𝑙𝑜𝑛𝑔 =
4𝑡
Rewrite the equation for thickness,
𝑝𝑑𝑖 600 𝑝𝑠𝑖 (120 𝑖𝑛. )
𝑡= = = 𝟏. 𝟏𝟏 𝒊𝒏.
4𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 4(16250)

The welds in real steel tanks contain defects, which reduce the strength of the welds. We can
measure the strength of welded joints in the lab and compare them with the strength of the
base metal. If the strengths match, we say the joint is 100% efficient. The symbol for
efficiency is the Greek letter eta, η.

5.1.3 Example #3
What is the minimum thickness of the spherical steel tank in Example#2 if the joint
efficiency is 80%?

Solution:
Use the same equations as before, except the allowable stress is multiplied by the joint
efficiency.
Longitudinal stress:
𝑝𝑑𝑖
𝜂𝑗𝑜𝑖𝑛𝑡 𝜎𝑙𝑜𝑛𝑔 =
4𝑡
Therefore,
𝑝𝑑𝑖 600 𝑝𝑠𝑖 (120 𝑖𝑛. )
𝑡= = = 𝟏. 𝟑𝟖 𝒊𝒏.
4𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 𝜂𝑗𝑜𝑖𝑛𝑡 4(16250)(0.8)

5.2 Stress Concentration in Tension

Pull a solid bar in tension, and the tensile stress in the


𝑃
bar is uniform within the bar: 𝜎 = 𝐴 where 𝐴𝑔𝑟𝑜𝑠𝑠
𝑔𝑟𝑜𝑠𝑠
the gross cross-sectional area of the bar. If the bar has
a hole in it, we would expect the stress to be higher
𝑃
because there is less material: 𝜎𝑛𝑒𝑡 = where 𝐴𝑛𝑒𝑡
𝐴𝑛𝑒𝑡
is the net cross-sectional area of the bar (gross area
minus the area of the hole). Experiments show the
stress is not uniform within the remaining solid
material; instead, it is highest next to the hole, and
lower as you move away from the hole. We say that
the stress is concentrated next to the hole.

4
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

𝑃
The maximum stress adjacent to the hole is 𝜎𝑚𝑎𝑥 = 𝐾𝜎𝑛𝑒𝑡 = 𝐾 𝐴 , where K is a stress
𝑛𝑒𝑡
concentration factor that depends on the size of the bar and the diameter of the hole. In
general, the smaller the radius, the higher the stress. For example, cracks have very high
stress concentrations at their tips, exceeding the tensile strength of the material, even though
the average stress in the part is below the yield strength. This is why cracks grow.

One way to prevent a crack


from growing in a material is
to drill a hole at its tip. The
drillhole has a larger radius,
which reduces the stress to
below the yield strength of the
material, and the crack is
blunted.

Stress concentrations can


occur anywhere there is a
change in geometry with a
small radius, such as holes,
fillets, and grooves. In the
1930s, M.M. Frocht 6
published a series of graphs relating K to the dimensions of the bar and hole (or fillet
orgroove), and R.E. Peterson published scientific papers on fatigue cracks which start at
stress concentrations. Peterson's book on stress concentration factors7 is still in print.

This graph is based on Frocht's original work. Use a four-step process to solve stress
concentration problems:

Step 1: Divide the hole diameter by the gross width of the bar to find the ratio 𝑑 /ℎ𝑔𝑟𝑜𝑠𝑠 .
Step 2: Find the value of K from the graph.
Step 3: Calculate the net cross-sectional area (gross cross-sectional area minus the cross-
sectional area of the hole). The
easiest way to find this value is to multiply the net width by the thickness.
𝑃
Step 4: Calculate the maximum stress using 𝜎𝑚𝑎𝑥 = 𝐾 𝐴 .
𝑛𝑒𝑡

5.2.1 Example #1
A bar measuring 80 mm wide by 16 mm thick has a 20 mm diameter hole in the center.
The tensile load on the bar is 900 N. Calculate the maximum stress in the bar due to the
stress concentration. Report the result in MPa.

5
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

Solution:
Divide the hole diameter by the gross cross-sectional width of the bar:

𝑑 20 𝑚𝑚
= = 0.25
ℎ𝑔𝑟𝑜𝑠𝑠 80 𝑚𝑚

Use the graph to find K≈ 2.36 . The net cross-sectional area of the bar is the net width
times the thickness. The net width is the gross width minus the hole diameter:

𝐴𝑛𝑒𝑡 = (80 𝑚𝑚 − 20 𝑚𝑚)16 𝑚𝑚 = 960 𝑚𝑚2

Maximum stress is
𝑃 900 𝑁
𝜎𝑚𝑎𝑥 = 𝐾 = 2.36 = 𝟐. 𝟐 𝑴𝑷𝒂
𝐴𝑛𝑒𝑡 960 𝑚𝑚

Use a similar four-step process to solve stress concentration problems in tensile bars having
fillets or semicircular grooves.
Step 1: Divide the groove or fillet radius by the net width of the bar to find the ratio 𝑑 /ℎ𝑔𝑟𝑜𝑠𝑠 .
Step 2: Find the value of K from the graph on the following page. Be sure to use the right
curve!
Step 3: Calculate the net cross-sectional area at the groove or fillet.
𝑃
Step 4: Calculate the maximum stress using 𝜎𝑚𝑎𝑥 = 𝐾 𝐴 .
𝑛𝑒𝑡

5.2.2 Example #2
A 0.25 in. thick, 2 in. wide bar has two semicircular 3/8 in. radius grooves. Find the
maximum stress in the bar due to the stress concentration. Report the result in ksi.

Solution:
Net width, ℎ𝑛𝑒𝑡 = 2𝑖𝑛. −2(0.375𝑖𝑛. ) = 1.25 𝑖𝑛.

Calculate
𝑟 0.375 𝑖𝑛.
= = 0.30
ℎ𝑛𝑒𝑡 1.25 𝑖𝑛.

From the graph on the next page, K≈ 1.82 . The net cross-sectional area is the net width
times the thickness:
𝐴𝑛𝑒𝑡 = 1.25 𝑖𝑛.× 0.25 𝑖𝑛. = 0.3125 𝑖𝑛2
Max. stress is:
2 𝑘𝑖𝑝𝑠
𝑃 1 𝑡𝑜𝑛 ×
𝜎𝑚𝑎𝑥 =𝐾 = 1.82 1 𝑡𝑜𝑛 = 11.6 𝑘𝑠𝑖
𝐴𝑛𝑒𝑡 0.3125 𝑖𝑛.2

6
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

5.3 Key Equations

 Hoop stress in a pressure vessel is equal to the internal pressure times the inside
diameter divided by twice the wall thickness:

𝑝𝑑𝑖
𝜎ℎ𝑜𝑜𝑝 =
2𝑡

This equation is used for pipes and cylinders.

 Longitudinal stress in a pressure vessel is equal to the internal pressure times the
inside diameter divided by four times the wall thickness:

𝑝𝑑𝑖
𝜎𝑙𝑜𝑛𝑔 =
4𝑡
This equation is used for spherical pressure vessels.

 For welded tanks, the ASME Boiler Code recommends using

7
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

1 2
𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 = 4 𝜎𝑈𝑇𝑆 or 𝜎𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 = 3 𝜎𝑌𝑆
whichever is smaller

 Stress at a stress concentration equal to the stress concentration factor times the
average stress at the net cross-sectional area:

𝑃
𝜎𝑚𝑎𝑥 = 𝐾
𝐴𝑛𝑒𝑡

Use stress concentration graphs to find the value of K.

5.4 Exercises

5.4.1
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm.
The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the
maximum internal pressure that can be applied if the longitudinal stress is limited to 140
MPa, and the circumferential (hoop) stress is limited to 60 MPa.

5.4.2
The thin-walled pressure vessel has an elliptical cross section with the dimensions shown in
the figure. Assuming that a > b and that the wall thickness t is constant, derive the
expressions for the maximum and minimum circumferential stresses in the vessel caused by
an internal pressure p.

5.4.3
The cylindrical tank with a spherical end-cap has an outer radius of 2 m and a wall thickness
of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal and
circumferential stresses in the cylinder, and the stress in the end-cap.

8
LESSSON 5: PRESSURE VESSELS AND STRESS CONCENTRATION

5.4.4
A spherical weather balloon is made of 0.2-mm-thick fabric that has a tensile strength of 10
MPa. The balloon is designed to reach an altitude where the interior pressure is 1500 Pa
above the atmospheric pressure. Find the largest allowable diameter of the balloon, using
1.2 as the factor of safety.

5.4.5
A spherical shell with 70-in. outer diameter and 67-in. inner diameter containshelium at a
pressure of 1200 psi. Compute the stress in the shell.

5.4.6
A steel plate measuring 150 mm wide by 20 mm thick has a 25 mm diameter hole in the
center. 1500 N of tensile load is applied on the steel plate. Calculate the maximum stress in
the bar due to the stress concentration. Report the result in MPa.

You might also like