R1162x SERIES: 3-Mode 150ma Ldo Regulator Outline

R1162x SERIES
3-MODE 150mA LDO REGULATOR

NO.EA-110-0512
OUTLINE
The R1162x Series consist of CMOS-based voltage regulator ICs with high output voltage accuracy and low
supply current. Each of these voltage regulator ICs consists of a voltage reference unit, an error amplifier,
resistors for setting output voltage, a current limit circuit, and so on. The output voltage is internally fixed with
high accuracy.
These ICs perform with the chip enable function and realize a standby mode with ultra low supply current. To
prevent the destruction by over current, the current limit circuit is included. The R1162x Series have 3-mode.
One is standby mode with CE or standby control pin. Other two modes are realized with ECO pin™. Fast
Transient Mode (FT mode) and Low Power Mode (LP mode) are alternative with ECO pin™. Consumption
current is reduced at Low Power Mode compared with Fast Transient Mode. The output voltage is maintained
between FT mode and LP mode.
Since the packages for these ICs are SOT-23-5 and SON1612-6 packages, high density mounting of the ICs
on boards is possible.
FEATURES
• Ultra-Low Supply Current..................................Typ. 5.5µA (Low Power Mode),
Typ. 70µA (Fast Transient Mode)
• Standby Mode ...................................................Typ. 0.1µA
• Low Dropout Voltage.........................................Typ. 0.25V (IOUT=150mA Output Voltage=3.0V Type)
• High Ripple Rejection .......................................Typ. 70dB (f=1kHz, FT Mode)
Typ. 60dB (f=10kHz, FT Mode)
• Low Temperature-Drift Coefficient of Output Voltage Typ. ±100ppm/°C
• Excellent Line Regulation .................................Typ. 0.02%/V
• High Output Voltage Accuracy ..........................±2.0%(±3.0% at LP Mode)
• Small Package ................................................SOT-23-5 (Super Mini-mold), SON1612-6
• Output Voltage ..................................................Stepwise setting with a step of 0.1V
in the range of 1.5V to 4.0V is possible
• Built-in fold-back protection circuit ....................Typ. 40mA (Current at short mode)
• Performs with Ceramic Capacitors ...................CIN=1.0µF,COUT=0.47µF
APPLICATIONS
• Precision Voltage References.
• Power source for electrical appliances such as cameras, VCRs and hand-held communication equipment.
• Power source for battery-powered equipment.
1
R1162x
BLOCK DIAGRAM
R1162xxx1B R1162xxx1D
ECO ECO
VDD VOUT VDD VOUT
Vref Vref
Current Limit Current Limit
CE GND CE GND
SELECTION GUIDE
The output voltage, function of auto-discharge, package, and the packing type for the ICs can be selected at
the user's request. The selection can be available by designating the part number as shown below;
R1162xxx1x-xx ←Part Number

↑↑ ↑ ↑
a b c d
Code Contents
Designation of Package Type :
a
N:SOT-23-5 (Mini-mold) D:SON1612-6
Setting Output Voltage (VOUT) :
b Stepwise setting with a step of 0.1V in the range of 1.5V to 4.0V is possible.
Exceptions: 1.85V=R1162x181x5, 2.85V=R1162x281x5
Designation of Chip Enable Option :
c B: "H" active type.
D: "H" active type. With auto discharge function
Designation of Taping Type :
d
Refer to Taping Specifications;TR type is the standard direction.
2
R1162x
PIN CONFIGURATIONS
SOT-23-5 SON1612-6
5 4 6 5 4
(mark side)
1 2 3 1 2 3
PIN DESCRIPTIONS
• R1116N (SOT-23-5) • R1116D (SON1612-6)
Pin No. Symbol Description Pin No. Symbol Description
1 VDD Input Pin 1 CE Chip Enable Pin
2 GND Ground Pin 2 GND Ground Pin
3 CE Chip Enable Pin 3 VDD Input Pin
4 ECO MODE alternative pin 4 VOUT Output Pin
5 VOUT Output pin 5 GND Ground Pin
6 ECO MODE alternative pin
ABSOLUTE MAXIMUM RATINGS

Symbol Item Rating Unit
VIN Input Voltage 6.5 V
VECO Input Voltage (ECO Pin) −0.3 to 6.5 V
VCE Input Voltage ( CE / CE Pin) −0.3 to 6.5 V
VOUT Output Voltage −0.3 to VIN+0.3 V
IOUT Output Current 180 mA
∗1
Power Dissipation (SOT-23-5) 420 mW
PD
∗1
Power Dissipation (SON1612-6) 500 MW
Topt Operating Temperature Range −40 ~ 85 °C
Tstg Storage Temperature Range −55 ~ 125 °C
∗1 For Power Dissipation, please refer to PACKAGE INFORMATION to be described.
3
R1162x
ELECTRICAL CHARACTERISTICS
• R1162xxx1B/D Topt=25°C
Symbol Item Conditions Min. Typ. Max. Unit

VIN = Set VOUT+1V VECO = VIN VOUT VOUT
Note 1 V
1mA < = IOUT <
= 30mA ×0.98 ×1.02
VOUT Output Voltage
VIN = Set VOUT + 1V VECO =GND VOUT VOUT
Note 2 V
1mA < = IOUT <
= 30mA ×0.97 ×1.03
Output Voltage Deviation VIN = Set VOUT+1V, IOUT =30mA
−1.2 0.0 1.2 %
∆VOUT between FT Mode and LP VOUT <= 2.0V
Mode VOUT >= 2.0V (−24) 0.0 (24) mV
IOUT Output Current VIN − VOUT = 1.0V 150 mA
VIN =Set VOUT+1V, VECO=VIN
Load Regulation(FT Mode) 20 40 mV
∆VOUT/ 1mA < = IOUT <
= 150mA
∆IOUT VIN = Set VOUT+1V,VECO=GND
Load Regulation(LP Mode) 20 45 mV
1mA < = IOUT <
= 150mA
VDIF Dropout Voltage Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
VIN = Set VOUT+1V
ISS1 Supply Current(FT Mode) 70 100 µA
VECO = VIN, IOUT=0mA
VIN = Set VOUT+1V
ISS2 Supply Current(LP Mode) 5.5 9.0 µA
VECO = GND, IOUT=0mA
Istandby Supply Current (Standby) VIN = VCE = Set VOUT+1V 0.1 1.0 µA
Set VOUT+0.5V < = VIN <
= 6.0V
Line Regulation(FT Mode) IOUT = 30mA, VECO = VIN 0.02 0.10 %/V
∆VOUT/ VOUT <= 1.6V: 2.2V < = VIN <= 6.0V
∆VIN Set VOUT + 0.5V < = VIN <
= 6.0V
Line Regulation(LP Mode) IOUT = 30mA, VECO = GND 0.05 0.20 %/V
VOUT <= 1.6V: 2.2V < = VIN <= 6.0V
f = 1kHz 70
f = 10kHz,Ripple 0.2Vp-p 60
RR Ripple Rejection(FT Mode) dB
VIN = Set VOUT + 1V
IOUT = 30mA, VECO = VIN
VIN Input Voltage 2.0 6.0 V
∆VOUT/ Output Voltage IOUT = 30mA ppm
±100
∆Topt Temperature Coefficient −40°C < = Topt < = 85°C /°C
Ilim Short Current Limit VOUT = 0V 40 mA
CE Pull-down
IPD 0.3 0.6 µA
Constant Current
RPD ECO Pull-down Resistance 2 5 30 MΩ
VCEH CE, ECO Input Voltage “H” 1.0 6.0 V
VCEL CE, ECO Input Voltage “L” 0.00 0.35 V
en Output Noise (Fast Mode) BW = 10Hz to 100kHz 30 µVrms
Output Noise
en BW = 10Hz to 100kHz 40 µVrms
(Low Power Mode)
Nch On resistance for
RLOW auto-discharge VCE=0V 60 Ω
(Applied to D version)
4
R1162x
ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE

Topt = 25°C
Dropout Voltage (mV)
Output Voltage
VOUT (V) VDIF(ECO=H) VDIF(ECO=L)
Condition
Typ. Max. Typ. Max.
1.5 <
= VOUT <
= 1.6 400 680 420 680
1.6 <
= VOUT <
= 1.7 380 550 390 550
1.7 <
= VOUT <
= 1.8 350 520 370 520
IOUT = 150mA
1.8 <
= VOUT <
= 2.0 340 490 350 490
2.0 <
= VOUT <
= 2.8 290 425 300 430
2.8 <
= VOUT <
= 4.0 250 350 250 350
TYPICAL APPLICATION
IN OUT
VDD OUT
R1162x
C1
SERIES
GND C2
CE･CE ECO
(External Components)
C2 Ceramic 0.47µF Ex. Murata GRM40B474K
Kyocera CM105B474K
C1 Ceramic 1.0µF
5
R1162x
TYPICAL CHARACTERISTICS Unless otherwise provided, capacitors are ceramic type.

1) Output Voltage vs. Output Current
R1162x15x (ECO=H) R1162x15x (ECO=L)
1.6 1.6
Output Voltage H VOUTH(V)
1.4 1.4
Output Voltage L VOUTL(V)

1.2 VIN=2V 1.2 VIN=2V
1.0 VIN=2.5V • 3.5V 1.0 VIN=2.5V • 3.5V

0.8 0.8
0.6 0.6
0.4 0.4
0.2 0.2
0.0 0.0
0 100 200 300 400 0 100 200 300 400
Output Current IOUT(mA) Output Current IOUT(mA)

3.0 3.0
2.5 VIN=3.1V 2.5 VIN=3.1V

VIN=3.3V VIN=3.3V
2.0 2.0
VIN=3.8V 4.8V
• VIN=3.8V • 4.8V
1.5 1.5
1.0 1.0
0.5 0.5
0.0 0.0
0 100 200 300 400 0 100 200 300 400

4.5 4.5
4.0 4.0
VIN=4.3V VIN=4.3V
3.5 3.5
3.0 VIN=4.5V 3.0 VIN=4.5V
VIN=5.0V • 6.0V VIN=5.0V • 6.0V
2.5 2.5
2.0 2.0
1.5 1.5
1.0 1.0
0.5 0.5
0.0 0.0
0 100 200 300 400 0 100 200 300 400
6
R1162x
2) Output Voltage vs. Input Voltage

1.6 1.6
1.4 1.4

1.2 1.2
1.0 1.0
0.8 0.8
0.6 0.6
0.4 IOUT=1mA 0.4 IOUT=1mA
IOUT=30mA IOUT=30mA
0.2 0.2
IOUT=50mA IOUT=50mA
0.0 0.0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
Input Voltage VIN(V) Input Voltage VIN(V)

3.0 3.0
2.5 2.5
2.0 2.0
1.5 1.5
1.0 1.0
IOUT=1mA IOUT=1mA
IOUT=50mA IOUT=50mA
0.0 0.0
0 1 2 3 4 5 6 0 1 2 3 4 5 6

4.5 4.5
4.0 4.0
3.5 3.5
3.0 3.0
2.5 2.5
2.0 2.0
1.5 1.5
IOUT=30mA IOUT=30mA
0.0 0.0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
7
R1162x
3) Supply Current vs. Input Voltage

80 7
70
Supply Current H ISSH(µA)
Supply Current L ISSL(µA)

6
60
5
50
4
40
3
30
2
20
10 1
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6

80 11
70 10
9
60 8
50 7
6
40
5
30 4
20 3
2
10 1
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6

80 12
11
70
10
60 9
8
50
7
40 6
5
30
4
20 3
2
10
1
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
8
R1162x
4) Output Voltage vs. Temperature

1.53 1.53

1.52 1.52
1.51 1.51
1.50 1.50
1.49 1.49
1.48 1.48
1.47 1.47
1.46 1.46
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
Temperature Topt(°C) Temperature Topt(°C)

2.83 2.83
2.82 2.82
2.81 2.81
2.80 2.80
2.79 2.79
2.78 2.78
2.77 2.77
2.76 2.76
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100

4.05 4.06
4.04 4.05
4.03 4.04
4.02 4.03
4.01 4.02
4.00 4.01
3.99 4.00
3.98 3.99
3.97 3.98
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
9
R1162x
5) Supply Current vs. Temperature

90 8
80 7

70 6
60
5
50
4
40
3
30
20 2
10 1
0 0
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100

90 8
80 7
70 6
60
5
50
4
40
3
30
20 2
10 1
0 0
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100

90 8
80 7
70 6
60
5
50
4
40
3
30
20 2
10 1
0 0
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
10
R1162x
6) Dropout Voltage vs. Output Current

0.5 0.5
85°C 85°C
Dropout Voltage H VDIFH(V)
Dropout Voltage L VDIFL(V)

0.4 25°C 0.4 25°C
-40°C -40°C
0.3 0.3
0.2 0.2
0.1 0.1
0.0 0.0
0 25 50 75 100 125 150 0 25 50 75 100 125 150

0.5 0.5
85°C 85°C
0.4 25°C 0.4 25°C

-40°C -40°C
0.3 0.3
0.2 0.2
0.1 0.1
0.0 0.0
0 25 50 75 100 125 150 0 25 50 75 100 125 150

0.5 0.5
85°C 85°C
0.4 25°C 0.4 25°C

-40°C -40°C
0.3 0.3
0.2 0.2
0.1 0.1
0.0 0.0
0 25 50 75 100 125 150 0 25 50 75 100 125 150
11
R1162x

0.5 0.5
85°C 85°C

0.4 25°C 0.4 25°C
-40°C -40°C
0.3 0.3
0.2 0.2
0.1 0.1
0.0 0.0
0 25 50 75 100 125 150 0 25 50 75 100 125 150

0.4 0.4
85°C 85°C
25°C 25°C
0.3 -40°C 0.3 -40°C
0.2 0.2
0.1 0.1
0.0 0.0
0 25 50 75 100 125 150 0 25 50 75 100 125 150

0.30 0.30
85°C 85°C
0.25 25°C 0.25 25°C

-40°C -40°C
0.20 0.20
0.15 0.15
0.10 0.10
0.05 0.05
0.00 0.00
0 25 50 75 100 125 150 0 25 50 75 100 125 150
12
R1162x

0.30 0.30
85°C 85°C

0.25 25°C 0.25 25°C
-40°C -40°C
0.20 0.20
0.15 0.15
0.10 0.10
0.05 0.05
0.00 0.00
0 25 50 75 100 125 150 0 25 50 75 100 125 150
7) Dropout Voltage vs. Set Output Voltage

R1162x (ECO=H) R1162x (ECO=L)
0.50 0.50
IOUT=10mA IOUT=10mA
Dropout Voltage H VDIFL(V)
IOUT=30mA IOUT=30mA
IOUT=100mA IOUT=100mA
0.30 IOUT=150mA 0.30 IOUT=150mA
0.20 0.20
0.10 0.10
0.00 0.00
1.5 2.0 2.5 3.0 3.5 4.0 1.5 2.0 2.5 3.0 3.5 4.0
Set Output Voltage VREG(V) Set Output Voltage VREG(V)
8) Ripple Rejection vs. Input Bias Voltage

R1162x28x (ECO=H) R1162x28x (ECO=H)
CIN=none, COUT=0.47µF, CIN=none, COUT=0.47µF,
IOUT=1mA Ripple=0.2Vp-p IOUT=1mA Ripple=0.5Vp-p
90 90
80 80
Ripple Rejection RR(dB)
70 70
60 60
50 50
40 40
30 30
20 f=1kHz 20 f=1kHz
f=10kHz f=10kHz
10 f=100kHz 10 f=100kHz
0 0
2.9 3.0 3.1 3.2 3.3 2.9 3.0 3.1 3.2 3.3
13
R1162x

90 90
80 80

70 70
60 60
50 50
40 40
30 30
20 f=1kHz 20 f=1kHz
f=10kHz f=10kHz
10 f=100kHz 10 f=100kHz
0 0
2.9 3.0 3.1 3.2 3.3 2.9 3.0 3.1 3.2 3.3

90 90
80 80
70 70
60 60
50 50
40 40
30 30
20 f=1kHz 20 f=1kHz
f=10kHz f=10kHz
10 f=100kHz 10 f=100kHz
0 0
2.9 3.0 3.1 3.2 3.3 2.9 3.0 3.1 3.2 3.3
9) Ripple Rejection vs. Frequency

VIN=2.5VDC+0.2Vp-p VIN=2.5VDC+0.2Vp-p
80 70
Ripple Rejection RR_H(dB)
IOUT=1mA
Ripple Rejection RR_L(dB)
70 60
IOUT=30mA
60 IOUT=50mA
50
50
40
40
30
30
20
20 IOUT=1mA
IOUT=30mA 10
10 IOUT=50mA
0 0
0.1 1 10 100 0.1 1 10 100
Frequency f(kHz) Frequency f(kHz)
14
R1162x

80 70
IOUT=1mA

70 60 IOUT=30mA
60 IOUT=50mA
50
50
40
40
30
30
IOUT=1mA 20
20
IOUT=30mA
10 IOUT=50mA 10
0 0
0.1 1 10 100 0.1 1 10 100

80 70
IOUT=1mA
70 60
IOUT=30mA
60 IOUT=50mA
50
50
40
40
30
30
IOUT=1mA 20
20
IOUT=30mA
10 IOUT=50mA 10
0 0
0.1 1 10 100 0.1 1 10 100
10) Input Transient Response

CIN=none, COUT=0.47µF, IOUT=30mA CIN=none, COUT=0.47µF, IOUT=10mA
1.58 4 3.5 4
1.56 3 3.0 3
Output Voltage VOUT(V)
Input Voltage Input Voltage

Input Voltage VIN(V)
1.54 2 2.5 2
1.52 1 2.0 1
1.50 0 1.5 0
Output Voltage Output Voltage
1.48 -1 1.0 -1
1.46 -2 0.5 -2
0 10 20 30 40 50 60 70 80 90 100 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Time t(µs) Time t(ms)
15
R1162x
R1162x15x (ECO=L) R1162x28x (ECO=H)

CIN=none, COUT=1µF, IOUT=10mA CIN=none, COUT=0.47µF, IOUT=30mA
3.5 4 2.88 6
3.0 3 2.86 5

Input Voltage

2.5 2 2.84 Input Voltage 4
2.0 1 2.82 3
1.5 0 2.80 2
1.0 -1 2.78 1
0.5 -2 2.76 0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 10 20 30 40 50 60 70 80 90 100
Time t(ms) Time t(µs)
R1162x28x (ECO=L) R1162x28x (ECO=L)

CIN=none, COUT=0.47µF, IOUT=10mA CIN=none, COUT=1µF, IOUT=10mA
5.0 6 5.0 6
4.5 5 4.5 5


4.0 Input Voltage 4 4.0 Input Voltage 4
3.5 3 3.5 3
3.0 2 3.0 2
2.5 Output Voltage 1 2.5 Output Voltage 1
2.0 0 2.0 0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Time t(ms) Time t(ms)
11) Load Transient Response

VIN=2.5V, CIN=1µF, COUT=0.47µF VIN=2.5V, CIN=1µF, COUT=0.47µF
1.9 150 1.9 60
Output Current IOUT(mA)
1.8 100 1.8 30

Output Current
1.7 Output Current 50 1.7 0
1.6 0 1.6 -30
1.5 -50 1.5 -60

1.4 -100 1.4 -90
1.3 -150 1.3 -120

0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Time t(µs) Time t(µs)
16
R1162x

VIN=2.5V, CIN=1µF, COUT=1µF VIN=2.5V, CIN=1µF, COUT=0.47µF
1.9 60 1.9 20

1.8 30 1.8 10

Output Current Output Current
1.7 0 1.7 0
1.6 -30 1.6 -10
1.5 -60 1.5 -20

1.4 -90 1.4 -30
1.3 -120 1.3 -40

0 2 4 6 8 10 12 14 16 18 20 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
R1162x15x (ECO=L) R1162x28x (ECO=H)

1.9 20 3.2 150

1.8 10 3.1 100

1.7 0 3.0 50
1.6 -10 2.9 0
1.5 -20 2.8 -50

1.4 -30 2.7 -100
1.3 -40 2.6 -150

0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 2 4 6 8 10 12 14 16 18 20
Time t(ms) Time t(µs)

3.2 150 3.2 60

3.1 100 3.1 30

3.0 50 3.0 0
2.9 0 2.9 -30
2.8 -50 2.8 -60

2.7 -100 2.7 -90
2.6 -150 2.6 -120

0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Time t(µs) Time t(µs)
17
R1162x

3.2 60 5.0 20

3.1 30 4.5 10

3.0 0 4.0 0
2.9 -30 3.5 -10
2.8 -60 3.0 -20

Output Voltage
2.7 -90 2.5 Output Voltage -30
2.6 -120 2.0 -40

0 2 4 6 8 10 12 14 16 18 20 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
R1162x28x (ECO=L)
VIN=3.8V, CIN=1µF, COUT=1µF
5.0 20
4.5 10
Output Current
4.0 0
3.5 -10
3.0 -20
2.5 Output Voltage -30
2.0 -40
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Time t(ms)
12) Turn on speed with CE pin

VIN=2.5V, CIN=1µF, VIN=2.5V, CIN=1µF,
COUT=0.47µF, IOUT=0mA COUT=0.47µF, IOUT=0mA
3 3.5 3 3.5
2 3.0 2 3.0
CE Input Voltage VCE(V)

1 CE Input Voltage 2.5 1 CE Input Voltage 2.5

0 2.0 0 2.0
-1 1.5 -1 1.5
-2 Output Voltage 1.0 -2 Output Voltage 1.0
-3 0.5 -3 0.5
-4 0.0 -4 0.0
-5 -0.5 -5 -0.5
-8 -4 0 4 8 12 16 20 24 28 32 -40 -20 0 20 40 60 80 100 120
18
R1162x

3 3.5 3 3.5
2 3.0 2 3.0


0 2.0 0 2.0
-1 1.5 -1 1.5
-2 Output Voltage 1.0 -2 Output Voltage 1.0
-3 0.5 -3 0.5
-4 0.0 -4 0.0
-5 -0.5 -5 -0.5
-8 -4 0 4 8 12 16 20 24 28 32 -0.2 -0.1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

3 3.5 3 3.5
2 3.0 2 3.0


0 2.0 0 2.0
-1 1.5 -1 1.5
-2 1.0 -2 Output Voltage 1.0
-3 Output Voltage 0.5 -3 0.5
-4 0.0 -4 0.0
-5 -0.5 -5 -0.5
-8 -4 0 4 8 12 16 20 24 28 32 -0.2 -0.1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

6 7 6 7
4 6 4 6

1 CE Input Voltage 5 1 CE Input Voltage 5

0 4 0 4
-2 3 -2 3
-4 Output Voltage 2 -4 Output Voltage 2
-6 1 -6 1
-8 0 -8 0
-10 -1 -10 -1
-20 -10 0 10 20 30 40 50 60 70 80 -20 -10 0 10 20 30 40 50 60 70 80
19
R1162x

6 7 6 7
4 6 4 6


0 4 0 4
-2 3 -2 3
-6 1 -6 1
-8 0 -8 0
-10 -1 -10 -1
-20 -10 0 10 20 30 40 50 60 70 80 -0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32

6 7 6 7
4 6 4 6


0 4 0 4
-2 3 -2 3
-6 1 -6 1
-8 0 -8 0
-10 -1 -10 -1
-20 -10 0 10 20 30 40 50 60 70 80 -0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32

6 8 6 8
4 7 4 7


0 5 0 5
-2 4 -2 4
-4 3 -4 3
-8 1 -8 1
-10 0 -10 0
-12 -1 -12 -1
-20 -10 0 10 20 30 40 50 60 70 80 -8 -4 0 4 8 12 16 20 24 28 32
20
R1162x

6 8 6 8
4 7 4 7


0 5 0 5
-2 4 -2 4
-4 3 -4 3
-8 1 -8 1
-10 0 -10 0
-12 -1 -12 -1
-20 -10 0 10 20 30 40 50 60 70 80 -0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32

6 8 6 8
4 7 4 7


0 5 0 5
-2 4 -2 4
-4 3 -4 3
-8 1 -8 1
-10 0 -10 0
-12 -1 -12 -1
-20 -10 0 10 20 30 40 50 60 70 80 -0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
21
R1162x
13) Turn off speed with CE pin

R1162x15xD R1162x28xD
VIN=2.5V, CIN=1µF,COUT=0.47µF VIN=3.8V, CIN=1µF,COUT=0.47µF
3 3.5 4 8.0
2 3.0 3 7.0


1 5.0
0 2.0
0 4.0
-1 1.5
-1 3.0
-2 IOUT = 0mA 1.0 IOUT = 0mA
IOUT = 30mA -2 IOUT = 30mA 2.0
-3 IOUT = 150mA 0.5 -3 IOUT = 150mA 1.0
-4 0.0 -4 0.0
-5 -0.5 -5 -1.0
-0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32 -0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
R1162x40xD
VIN=5.0V, CIN=1µF,COUT=0.47µF
6 11
5 10
4 9
3 CE Input Voltage 8
2 7
1 6
0 5
-1 IOUT = 0mA 4
-2 IOUT = 30mA 3
-3 IOUT = 150mA 2
-4 1
-5 0
-6 -1
-0.08 -0.04 0.00 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
Time t(ms)
22
R1162x
14) Output Voltage at Mode alternative point

R1162x15x R1162x28x
VIN=2.5V, CIN=Ceramic 1.0µF, VIN=3.8V, CIN=Ceramic 1.0µF,
COUT=Ceramic 0.47µF COUT=Ceramic 0.47µF
3 4
ECO Input Voltage VECO(V)

2 3
1 2
0 1
0
1.52 2.82 -1
IOUT=1mA IOUT=1mA
1.50 2.80 -2
1.48 2.78 -3

1.52 2.82 -4
IOUT=10mA IOUT=10mA
1.50 2.80 -5
1.48 2.78 -6
1.52 2.82 -7
IOUT=50mA IOUT=50mA
1.50 2.80 -8
1.48 2.78 -9
1.52 2.82 -10
1.50 2.80 -11
1.48 2.78 -12
1.52 2.82 -13
1.50 2.80 -14
1.48 2.78 -15
-0.1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 -0.1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1.56 3 2.86 4
1.55 2 2.85 3
1.54 1 2.84 2
1.53 0 2.83 1
1.52 -1 2.82 0
1.51 IOUT=0mA -2 2.81 IOUT=0mA -1
1.50 -3 2.80 -2
1.49 -4 2.79 -3
1.48 -5 2.78 -4
-10 0 10 20 30 40 50 60 70 80 90 -10 0 10 20 30 40 50 60 70 80 90
23
R1162x
TECHNICAL NOTES
IN OUT
VDD OUT
R1162x
C1
SERIES
GND C2
CE･CE ECO
(External Components)
C2 Ceramic 0.47µF Ex. Murata GRM40B474K
Kyocera CM105B474K
C1 Ceramic 1.0µF
When using these ICs, consider the following points:
1.Mounting on PCB
Make VDD and GND lines sufficient. If their impedance is high, noise pickup or unstable operation may result.
Connect a capacitor with as much as 1.0µF capacitor between VDD and GND pin as close as possible.
Set external components, especially the output capacitor as close as possible to the ICs and make wiring as
short as possible.
2.Phase Compensation
In these ICs, phase compensation is made for securing stable operation even if the load current is varied. For
this purpose, be sure to use a 0.47µF or more capacitor COUT with good frequency characteristics and ESR
(Equivalent Series Resistance).
If you use a tantalum type capacitor and ESR value of the capacitor is large, output might be unstable.
Evaluate your circuit with considering frequency characteristics.
Depending on the capacitor size, manufacturer, and part number, the bias characteristics and temperature
characteristics are different. Evaluate the circuit with actual using capacitors.
24
R1162x
ESR vs. Output Current

When using these ICs, consider the following points:
In these ICs, phase compensation is made for securing stable operation even if the load current is varied.
For this purpose, be sure to use a capacitor COUT with good frequency characteristics and ESR (Equivalent
Series Resistance) in the range described as follows:
The relations between IOUT (Output Current) and ESR of Output Capacitor are shown below.
The conditions when the white noise level is under 40µV (Avg.) are marked as the hatched area in the graph.
<Test conditions>
(1) Frequency band: 10Hz to 2MHz
VIN=2.0V to 6.0V, CIN=1µF,COUT=0.47µF VIN=2.0V to 6.0V, CIN=1µF,COUT=0.47µF
100 100
Topt=85°C Topt=25°C
10 10
Topt=-40°C
ESR(Ω)
ESR(Ω)
1 1
0.1 0.1
0.01 0.01
0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140
Load Current IOUT(mA) Load Current IOUT(mA)

VIN=3.1V to 6.0V, CIN=1µF,COUT=0.47µF VIN=3.1V to 6.0V, CIN=1µF,COUT=0.47µF
100 100
Topt=85°C Topt=25°C
10 10
Topt=-40°C
ESR(Ω)
ESR(Ω)
1 1
0.1 0.1
0.01 0.01
0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140
Load Current IOUT(mA) Load Current IOUT(mA)
25
PACKAGE INFORMATION PE-SOT-23-5-0510
• SOT-23-5 (SC-74A) Unit: mm
PACKAGE DIMENSIONS
2.9±0.2
+0.2
1.9±0.2 1.1 −0.1
(0.95) (0.95)
0.8±0.1
5 4
1.6 −0.1
+0.2
2.8±0.3
0 to 0.1
1 2 3
+0.1
0.15 −0.05
0.2 MIN.
0.4±0.1
TAPING SPECIFICATION
1.75±0.1
+0.1 4.0±0.1
φ1.5 0 2.0±0.05
0.3±0.1
3.5±0.05
8.0±0.3
3.2
3.3
2.0MAX. 4.0±0.1
∅1.1±0.1
TR
User Direction of Feed
TAPING REEL DIMENSIONS

(1reel=3000pcs)
11.4±1.0
9.0±0.3
∅ 13±0.2
2±0.5
−1.5
∅60 +1
0
∅180 0
21±0.8
PACKAGE INFORMATION PE-SOT-23-5-0510
POWER DISSIPATION (SOT-23-5)

This specification is at mounted on board. Power Dissipation (PD) depends on conditions of mounting on board.
This specification is based on the measurement at the condition below:
(Power Dissipation (SOT-23-5) is substitution of SOT-23-6.)
Measurement Conditions
Standard Land Pattern
Environment Mounting on Board (Wind velocity=0m/s)
Board Material Glass cloth epoxy plactic (Double sided)
Board Dimensions 40mm × 40mm × 1.6mm
Copper Ratio Top side : Approx. 50% , Back side : Approx. 50%
Through-hole φ0.5mm × 44pcs
Measurement Result
(Topt=25°C,Tjmax=125°C)
Standard Land Pattern Free Air
Power Dissipation 420mW 250mW
Thermal Resistance θja=(125−25°C)/0.42W=263°C/W 400°C/W
600
40
500 On Board
Power Dissipation PD(mW)
420
400
Free Air
300
250
40
200
100
0
0 25 50 75 85 100 125 150
Ambient Temperature (°C)
Power Dissipation Measurement Board Pattern
IC Mount Area Unit : mm
RECOMMENDED LAND PATTERN

0.7 MAX.
1.0
2.4
0.95 0.95
1.9
(Unit: mm)
PACKAGE INFORMATION PE-SON1612-6-0510
• SON1612-6 Unit: mm
PACKAGE DIMENSIONS
1.6±0.1 0.3TYP. 0.5
(0.3)
(0.2)
6 4
1.2±0.05
1.6±0.05
(0.3)
1 3
0.125±0.055
0.6MAX.
0.08 0.22±0.05
0.08 M
TAPING SPECIFICATION
1.75±0.1
4.0±0.1
1.5 +0.1
0 2.0±0.05
0.25±0.1 3.5±0.05
8.0±0.3
1.75
1.1±0.1
1.75
1.1MAX. 4.0±0.1
TR
User Direction of Feed
TAPING REEL DIMENSIONS

(1reel=4000pcs)
11.4±1.0
9.0±0.3
∅ 13±0.2
2±0.5
−1.5
∅60 +1
0
∅180 0
21±0.8
PACKAGE INFORMATION PE-SON1612-6-0510
Power Dissipation (SON1612-6)

This specification is at mounted on board.
Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the
measurement at the condition below:
Measurement Conditions
Environment Mounting on Board (Wind velocity=0m/s)
Board Material Glass cloth epoxy plactic (Double sided)
Board Dimensions 40mm × 40mm × 1.6mm
Copper Ratio Top side : Approx. 50%, Back side : Approx.50%
Through-hole φ0.5mm × 24pcs
Measurement Result
(Topt=25°C,Tjmax=125°C)
Power Dissipation 500mW
Thermal Resistance θja=(125−25°C)/0.5W=200°C/W
600 39
500
Power Dissipation PD(mW)
On Board
400
300
40
27
39
200
100
0
27
0 25 50 75 85 100 125 150
40
Ambient Temperature (°C)
Power Dissipation Measurement Board Pattern
IC Mount Area Unit : mm
RECOMMENDED LAND PATTERN

0.28 0.5
0.45 0.45
(Unit: mm)
MARK INFORMATION ME-R1162N-0409
R1162N SERIES MARK SPECIFICATION

• SOT-23-5 (SC-74A)
1 , 2 , 3 : Product Code (refer to Part Number vs. Product Code)
4 , 5 : Lot Number
1 2 3 4 5
• Part Number vs. Product Code

Product Code Product Code
Part Number Part Number
1 2 3 1 2 3
R1162N151B S 1 5 R1162N151D T 1 5
R1162N161B S 1 6 R1162N161D T 1 6
R1162N171B S 1 7 R1162N171D T 1 7
R1162N181B S 1 8 R1162N181D T 1 8
R1162N191B S 1 9 R1162N191D T 1 9
R1162N201B S 2 0 R1162N201D T 2 0
R1162N211B S 2 1 R1162N211D T 2 1
R1162N221B S 2 2 R1162N221D T 2 2
R1162N231B S 2 3 R1162N231D T 2 3
R1162N241B S 2 4 R1162N241D T 2 4
R1162N251B S 2 5 R1162N251D T 2 5
R1162N261B S 2 6 R1162N261D T 2 6
R1162N271B S 2 7 R1162N271D T 2 7
R1162N281B S 2 8 R1162N281D T 2 8
R1162N291B S 2 9 R1162N291D T 2 9
R1162N301B S 3 0 R1162N301D T 3 0
R1162N311B S 3 1 R1162N311D T 3 1
R1162N321B S 3 2 R1162N321D T 3 2
R1162N331B S 3 3 R1162N331D T 3 3
R1162N341B S 3 4 R1162N341D T 3 4
R1162N351B S 3 5 R1162N351D T 3 5
R1162N361B S 3 6 R1162N361D T 3 6
R1162N371B S 3 7 R1162N371D T 3 7
R1162N381B S 3 8 R1162N381D T 3 8
R1162N391B S 3 9 R1162N391D T 3 9
R1162N401B S 4 0 R1162N401D T 4 0
R1162N181B5 S 4 1 R1162N181D5 T 4 1
R1162N281B5 S 4 2 R1162N281D5 T 4 2
MARK INFORMATION ME-R1162D-0605
R1162D SERIES MARK SPECIFICATION

• SON1612-6
1 to 4 : Product Code (refer to Part Number vs. Product Code)
5 , 6 : Lot Number
1 2 3
4 5 6
• Part Number vs. Product Code

Product Code Product Code Product Code
Part Number Part Number Part Number
1 2 3 4 1 2 3 4 1 2 3 4
R1162D151B H 1 5 B R1162D151D H 1 5 D R1162D281E5 H 4 1 E

R1162D161B H 1 6 B R1162D161D H 1 6 D
R1162D171B H 1 7 B R1162D171D H 1 7 D
R1162D181B H 1 8 B R1162D181D H 1 8 D
R1162D191B H 1 9 B R1162D191D H 1 9 D
R1162D201B H 2 0 B R1162D201D H 2 0 D
R1162D211B H 2 1 B R1162D211D H 2 1 D
R1162D221B H 2 2 B R1162D221D H 2 2 D
R1162D231B H 2 3 B R1162D231D H 2 3 D
R1162D241B H 2 4 B R1162D241D H 2 4 D
R1162D251B H 2 5 B R1162D251D H 2 5 D
R1162D261B H 2 6 B R1162D261D H 2 6 D
R1162D271B H 2 7 B R1162D271D H 2 7 D
R1162D281B H 2 8 B R1162D281D H 2 8 D
R1162D291B H 2 9 B R1162D291D H 2 9 D
R1162D301B H 3 0 B R1162D301D H 3 0 D
R1162D311B H 3 1 B R1162D311D H 3 1 D
R1162D321B H 3 2 B R1162D321D H 3 2 D
R1162D331B H 3 3 B R1162D331D H 3 3 D
R1162D341B H 3 4 B R1162D341D H 3 4 D
R1162D351B H 3 5 B R1162D351D H 3 5 D
R1162D361B H 3 6 B R1162D361D H 3 6 D
R1162D371B H 3 7 B R1162D371D H 3 7 D
R1162D381B H 3 8 B R1162D381D H 3 8 D
R1162D391B H 3 9 B R1162D391D H 3 9 D
R1162D401B H 4 0 B R1162D401D H 4 0 D
R1162D181B5 H 4 1 B R1162D181D5 H 4 1 D
R1162D281B5 H 4 2 B R1162D281D5 H 4 2 D
www.s-manuals.com

R1162x SERIES: 3-Mode 150ma Ldo Regulator Outline

Uploaded by

Copyright:

Available Formats

R1162x SERIES: 3-Mode 150ma Ldo Regulator Outline

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

R1162x SERIES: 3-Mode 150ma Ldo Regulator Outline

Uploaded by

Copyright:

Available Formats

R1162x SERIES

3-MODE 150mA LDO REGULATOR

VDD VOUT VDD VOUT

Current Limit Current Limit

R1162xxx1x-xx ←Part Number

ABSOLUTE MAXIMUM RATINGS

Symbol Item Conditions Min. Typ. Max. Unit

ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE

TYPICAL CHARACTERISTICS Unless otherwise provided, capacitors are ceramic type.

Output Voltage L VOUTL(V)

1.0 VIN=2.5V • 3.5V 1.0 VIN=2.5V • 3.5V

R1162x28x (ECO=H) R1162x28x (ECO=L)

Output Voltage L VOUTL(V)

2.5 VIN=3.1V 2.5 VIN=3.1V

R1162x40x (ECO=H) R1162x40x (ECO=L)

Output Voltage L VOUTL(V)

2) Output Voltage vs. Input Voltage

Output Voltage L VOUTL(V)

R1162x28x (ECO=H) R1162x28x (ECO=L)

Output Voltage L VOUTL(V)

R1162x40x (ECO=H) R1162x40x (ECO=L)

Output Voltage L VOUTL(V)

3) Supply Current vs. Input Voltage

Supply Current L ISSL(µA)

R1162x28x (ECO=H) R1162x28x (ECO=L)

Supply Current L ISSL(µA)

R1162x40x (ECO=H) R1162x40x (ECO=L)

Supply Current L ISSL(µA)

4) Output Voltage vs. Temperature

Output Voltage L VOUTL(V)

R1162x28x (ECO=H) R1162x28x (ECO=L)

Output Voltage L VOUTL(V)

R1162x40x (ECO=H) R1162x40x (ECO=L)

5) Supply Current vs. Temperature

Supply Current L ISSL(µA)

R1162x28x (ECO=H) R1162x28x (ECO=L)

Supply Current L ISSL(µA)

R1162x40x (ECO=H) R1162x40x (ECO=L)

Supply Current L ISSL(µA)

6) Dropout Voltage vs. Output Current

Dropout Voltage L VDIFL(V)

R1162x16x (ECO=H) R1162x16x (ECO=L)

Dropout Voltage L VDIFL(V)

0.4 25°C 0.4 25°C

R1162x17x (ECO=H) R1162x17x (ECO=L)

Dropout Voltage L VDIFL(V)

0.4 25°C 0.4 25°C

R1162x18x (ECO=H) R1162x18x (ECO=L)

Dropout Voltage L VDIFL(V)

R1162x21x (ECO=H) R1162x21x (ECO=L)

Dropout Voltage L VDIFL(V)

R1162x28x (ECO=H) R1162x28x (ECO=L)

Dropout Voltage L VDIFL(V)

0.25 25°C 0.25 25°C

R1162x40x (ECO=H) R1162x40x (ECO=L)

Dropout Voltage L VDIFL(V)

7) Dropout Voltage vs. Set Output Voltage

Dropout Voltage H VDIFL(V)

8) Ripple Rejection vs. Input Bias Voltage