T315XW06 V5 Product Specification

Rev. 0.0

Model Name: T315XW06 V5

Issue Date : 2010/09/27

(＊
＊)Preliminary Specifications
( )Final Specifications

Customer Signature Date AUO Date

Approval By PM Director
Approved By
YenTing Chiu

_________________________________ ____________________________________

Note Reviewed By RD Director

Eugene CC Chen

____________________________________
Reviewed By Project Leader

Sarah Ke

____________________________________

Prepared By PM

Janna Huang

____________________________________

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 1 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

Contents
No
CONTENTS

RECORD OF REVISIONS

1 GENERAL DESCRIPTION

2 ABSOLUTE MAXIMUM RATINGS

3 ELECTRICAL SPECIFICATION

3-1 ELECTRIACL CHARACTERISTICS

3-2 INTERFACE CONNECTIONS

3-3 SIGNAL TIMING SPECIFICATION

3-4 SIGNAL TIMING WAVEFORMS

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE

3-7 BACKLIGHT SPECIFICATION

4 OPTICAL SPECIFICATION

5 MECHANICAL CHARACTERISTICS

6 RELIABILITY TEST ITEMS

7 INTERNATIONAL STANDARD

7-1 SAFETY

7-2 EMC

8 PACKING

8-1 DEFINITION OF LABEL

8-2 PACKING METHODS

8-3 PALLET AND SHIPMENT INFORMATION

9 PRECAUTIONS

9-1 MOUNTING PRECAUTIONS

9-2 OPERATING PRECAUTIONS

9-3 ELECTROSTATIC DISCHARGE CONTROL

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

9-5 STORAGE

9-6 HANDLING PRECAUTIONS FOR PROTECT FILM

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 2 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

Record of Revision
Version Date Page Description
0.0 2010/09/27 First release

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 3 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

1. General Description
This specification applies to the 31.5 inch Color TFT-LCD Module T315XW06 V5. This LCD module has a TFT
active matrix type liquid crystal panel 1,366 x 768 pixels, and diagonal size of 31.5 inch. This module supports
1,366 x 768 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical
stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.

The T315XW06 V5 has been designed to apply the 8-bit 1 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.

General Information

Items Specification Unit Note

Active Screen Size 31.5 inch
Display Area 697.685 (H) x 392.256(V) mm
Outline Dimension 735.4(H) x 433.0 (V) mm
Driver Element a-Si TFT active matrix
Display Colors 8 bit, 16.7M color
Number of Pixels 1,366 x 768 pixel
Pixel Pitch 0.51075 mm
Pixel Arrangement RGB vertical stripe
Display Operation Mode Normally Black
Surface Treatment Anti-Glare, 3H Haze=2%

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 4 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

2. Absolute Maximum Ratings

The followings are maximum values which, if exceeded, may cause faulty operation or damage to the unit

Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage Vcc -0.3 14 [Volt] Note 1
Input Voltage of Signal Vin -0.3 4 [Volt] Note 1
o
Operating Temperature TOP 0 +50 [ C] Note 2
Operating Humidity HOP 10 90 [%RH] Note 2
o
Storage Temperature TST -20 +60 [ C] Note 2
Storage Humidity HST 10 90 [%RH] Note 2
o
Panel Surface Temperature PST -- 65 [ C] Note 3

Note 1: Duration:50 msec.

Note 2 : Maximum Wet-Bulb should be 39 ℃ and No condensation.
The relative humidity must not exceed 90% non-condensing at temperatures of 40 ℃ or less. At temperatures
greater than 40℃, the wet bulb temperature must not exceed 39℃.
Note 3: Surface temperature is measured at 50℃ Dry condition

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 5 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

3. Electrical Specification
The T315XW06 V5 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The second input for BLU is to power inverter.

3-1 Electrical Characteristics

Value
Parameter Symbol Unit Note
Min. Typ. Max

LCD

Power Supply Input Voltage VDD 10.8 12 13.2 VDC 1

Power Supply Input Current IDD -- 0.26 0.33 A 2

Power Consumption PC -- 3.12 Watt 2

Inrush Current IRUSH -- -- 3 A 3

Differential Input High Threshold Voltage VTH +100 -- +300 mV 4

LVDS
Differential Input Low Threshold Voltage VTL -300 -- -100 mV 4
Interface
Input Common Mode Voltage VICM 1.1 1.25 1.4 VDC 4
VIH
Input High Threshold Voltage 2.7 -- 3.3 VDC --
CMOS (High)
Interface VIL
Input Low Threshold Voltage 0 -- 0.6 VDC --
(Low)
Backlight Power Consumption PBL -- 38.4 -- Watt --

Life Time 30,000 -- -- Hours 7

Note :
1. The ripple voltage should be controlled under 10% of VCC
2. Test Condition:
(1) VDD = 12.0V
(2) Fv = 60Hz
(3) FCLK = 80 Mhz (typ.), 86Mhz (max)
(4) Temperature = 25 ℃
(5) Test Pattern : White Pattern

3. Measurement condition : Rising time = 400us

VDD
90%

10%
GND

400 µs

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 6 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
4. VICM = 1.25V

V TH
V ICM
VTL

0V

5. Input Channel Pair Skew Margin

6. The relative humidity must not exceed 80% non-condensing at temperatures of 40 ℃ or less. At
temperatures greater than 40 ℃, the wet bulb temperature must not exceed 39℃. When operate at low
temperatures, the brightness of LED will drop and the life time of LED will be reduced.

7. The lifetime is defined as the time which luminance of LED is 50% compared to its original value.
℃
[Operating condition: Continuous operating at Ta = 25±2 ]

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 7 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
3-2 Interface Connections

LCD Connector - LVDS connector on transfer board : Starconn 093G30-B0001A-1
PIN Symbol Description
1 VDD Power Supply, +12V DC Regulated
2 VDD Power Supply, +12V DC Regulated
3 VDD Power Supply, +12V DC Regulated
4 VDD Power Supply, +12V DC Regulated
5 GND Ground
6 GND Ground
7 GND Ground
8 GND Ground
9 LVDS_SEL Open/High(3.3V) for NS, Low(GND) for JEIDA
10 Reserved AUO Internal Use Only
11 GND Ground
12 CH1_0- LVDS Channel 1, Signal 0-
13 CH1_0+ LVDS Channel 1, Signal 0+
14 GND Ground
15 CH1_1- LVDS Channel 1, Signal 1-
16 CH1_1+ LVDS Channel 1, Signal 1+
17 GND Ground
18 CH1_2- LVDS Channel 1, Signal 2-
19 CH1_2+ LVDS Channel 1, Signal 2+
20 GND Ground
21 CH1_CLK- LVDS Channel 1, Clock -
22 CH1_CLK+ LVDS Channel 1, Clock +
23 GND Ground
24 CH1_3- LVDS Channel 1, Signal 3-
25 CH1_3+ LVDS Channel 1, Signal 3+
26 GND Ground
27 Reserved AUO Internal Use Only
28 Reserved AUO Internal Use Only
29 GND Ground
30 GND Ground

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 8 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

LVDS Option = High/Open  NS

P re vio u s C y cle C u rren t C yc le N e xt C yc le

C lo ck

C H x_0+ R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
C H x_0-

C H x_1+ G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
C H x_1-

C H x_2+
C H x_2- B3 B2 DE NA NA B5 B4 B3 B2 DE

C H x_3+
C H x_3- R7 R6 NA B7 B6 G7 G6 R7 R6 NA

Note: x = 1, 2, 3, 4…

LVDS Option = Low  JEIDA

P re vio u s C yc le C u rren t C ycle N e x t C ycle

C lo ck

CH x_0+ R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
CH x_0-

CH x_1+ G4 G3 B3 B2 G7 G6 G5 G4 G3 B3
CH x_1-

CH x_2+
CH x_2- B5 B4 DE NA NA B7 B6 B5 B4 DE

CH x_3+
CH x_3- R1 R0 NA B1 B0 G1 G0 R1 R0 NA

Note: x = 1, 2, 3, 4…

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 9 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
3-3 Signal Timing Specification
This is the signal timing required at the input of the user connector. All of the interface signal timing should be
satisfied with the following specifications for its proper operation.

Signal Item Symbol Min. Typ. Max Unit

Period Tv 784 810 1015 Th
Vertical Section Active Tdisp (v) 768 Th
Blanking Tblk (v) 16 42 247 Th
Period Th 1460 1648 2000 Tclk
Horizontal Section Active Tdisp (h) 1366 Tclk
Blanking Tblk (h) 94 282 634 Tclk
Clock Frequency Fclk=1/Tclk 50 80 86 MHz
Vertical Frequency Frequency Fv 47 60 63 Hz
Horizontal
Frequency Fh 43 48 53 KHz
Frequency

Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2) Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3) If a period of DE “High” is less than 1,366 DCLK or less than 768 lines, the rest of the screen displays black.
(4) The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 10 / 29

Free Datasheet http://www.datasheet4u.net/
 Free Datasheet http://www.datasheet4u.net/
T315XW06 V5 Product Specification
Rev. 0.0

Page 11 / 29
Tv M pixel
Tblk(v) Tdisp(v)

N L in e
Th
DE
RGB Line Invalid Data Line Line Line Line Line Invalid Data
N 1 2 3 4 N
Data

© Copyright AUO Optronics Corp. 2009 All Rights Reserved.

CLK
Th
Tclk
Tdisp(h) Tblk(h)
DE
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH1 M-3 M-2 M-1 M
Invalid Data
1 2 3 4 5 6 M-2 M-1 M
Invalid Data
1 2
3-4 Signal Timing Waveforms
 T315XW06 V5 Product Specification
Rev. 0.0
3-5 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data
input.

Color Data Reference

Input Color Data
RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
R ----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
G ----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
B ----
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 12 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
3-6 Power Sequence for LCD

90% 90%
Pow er Supply For LCD
VD D (+ 12 V ) 10% 10% 10%
G ND

t1 t2 t5 t6 t7

Interface Signal Valid D ata

( LV DS Data & CLK )
G ND

t3 t4
Backlight on / off
control signal
( VBLO N ) GND

t8 t9
CM O S Interface Signal
G ND

Values
Parameter Unit
Min. Type. Max.
t1 0.4 --- 30 ms
t2 0.1 --- 50 ms
t3 450 --- --- ms
*1
t4 0 --- --- ms
t5 0 --- --- ms
*2
t6 --- --- --- ms
t7 500 --- --- ms
t8 10 --- 50 ms
t9 0 --- --- ms
Note:
(1) t4=0 : concern for residual pattern before BLU turn off.
(2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 13 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
3-7 Backlight Specification
The backlight unit contains 1-side lightbar.

3-7-1 Electrical Specification

Spec
Item Symbol Condition Unit Note
Min Typ Max

1 Input Voltage VDDB - 22.8 24 25.2 VDC -

2 Input Current IDDB VDDB=24V 1.6 1.69 ADC 1

3 Input Power PDDB VDDB=24V 38.4 40.66 W 1

4 Inrush Current IRUSH VDDB=24V 5 ADC 2

ON 2 - 5.5 -
5 On/Off control voltage VBLON VDDB=24V VDC
OFF 0 - 0.8 3

6 On/Off control current IBLON VDDB=24V - - 1.5 mA -

MAX 3.1 - 5.5 VDC 4

7 Dimming Control Voltage V_DIM VDDB=24V
MIN - 0 - VDC -

8 Dimming Control Current I_DIM VDDB=24V - - 2 mADC -

9 Internal Dimming Ratio DIM_R VDDB=24V 5 - 100 % 5

MAX VDDB=24V 2 - 5.5 -

External PWM
10 V_EPWM VDC
Control Voltage
MIN VDDB=24V 0 - 0.8 -
External PWM
11 I_EPWM VDDB=24V - - 2 mADC -
Control Current
12 External PWM Duty ratio D_EPWM VDDB=24V 5 - 100 % 5
External PWM
13 F_EPWM VDDB=24V 140 180 240 Hz -
Frequency
HI Open Collector VDC 6
14 DET status signal DET VDDB=24V
Lo 0 - 0.8 VDC 6

15 Input Impedance Rin VDDB=24V 300 Kohm -

Note 1 : Dimming ratio= 100% (MAX)（Ta=25±5℃, Turn on for 45minutes）

Note 2: Measurement condition Rising time = 20ms (VDDB : 10%~90%);
Note 3: When BLU off ( VDDB = 24V , VBLON = 0V) , IDDB (max) = 0.02A
Note 4: V_DIM voltage of 100% duty ratio =3.1V~3.3V means Burst Mode entry point should be
located between 3.1V and 3.3V.
Note 5: Less than 5% dimming control is functional well and no backlight shutdown happened
Note 6: Normal : 0~0.8V ; Abnormal : Open collector

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 14 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
3-7-2 Interface Connection

LED driver board connector : Cvilux CI1114M1HR0-NH

Pin Symbol Description

1 VDDB Operating Voltage Supply, +24V DC regulated

2 VDDB Operating Voltage Supply, +24V DC regulated

3 VDDB Operating Voltage Supply, +24V DC regulated

4 VDDB Operating Voltage Supply, +24V DC regulated

5 VDDB Operating Voltage Supply, +24V DC regulated

6 BLGND Ground and Current Return

7 BLGND Ground and Current Return

8 BLGND Ground and Current Return

9 BLGND Ground and Current Return

10 BLGND Ground and Current Return

BLU status detection:

11 DET Normal : 0~0.8V ; Abnormal : Open collector
(Recommend Pull high R > 10K, VDD = 3.3V)

BLU On-Off control:

12 VBLON High/Open (2~5.5V) : BL On ;

Low (0~0.8V/GND) : BL Off

13 NC NC

14 PDIM(*) External PWM (5%~100% Duty, open for 100%)

(Note*) IF External PWM function less than 5 % dimming ratio. Judge condition as below:
(1) Backlight module must be lighted ON normally.
(2) All protection function must work normally.
(3) Uniformity and flicker could NOT be guaranteed

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 15 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
3-7-3 Power Sequence for LED Driver

24V(typ.)
90% 90%

10%
Power Input for BLU
(VDDB)
T1 T2 T5

Dimming Control Signal

(V_IPWM,V_EPWM)
T3 T4

BLU On/Off Enable

(VBLON)

Dip condition for LED

Value
Parameter Units
Min Typ Max
T1 20 - - ms
T2 500 - - ms
T3 250 - - ms
T4 0 - - ms
T5 1 - - ms
T6 - - 10 ms

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 16 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of φ and θ equal to 0°.

Fig 1 presents additional information concerning the measurement equipment and method.

SR3 or equivalent

Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 2,400 3,000 -- -- 1
2
Surface Luminance (White) LWH 280 350 -- cd/m 2
Luminance Variation δWHITE(9P) -- -- 1.33 -- 3
Response Time (G to G) Tγ -- 6.5 -- Ms 4
Color Gamut NTSC -- 72 -- % --
Red RX 0.64 -- --
RY 0.33 -- --
Green GX 0.31 -- --
Color GY 0.62 -- --
Typ.-0.03 Typ.+0.03
Coordinates Blue BX 0.15 -- --
BY 0.06 -- --
White WX 0.280 -- --
WY 0.290 -- --
x axis, right(φ=0°) θr -- 89 -- degree 5
Viewing x axis, left(φ=180°) θl -- 89 -- degree 5
Angle y axis, up(φ=90°) θu -- 89 -- degree 5
y axis, down (φ=270°) θd -- 89 -- degree 5

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 17 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
Note:
1. Contrast Ratio (CR) is defined mathematically as:
Surface Luminance of Lon5
Contrast Ratio=
Surface Luminance of Loff5

2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 11mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, δWHITE is defined (center of Screen) as:
δWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time T γ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.

Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG4.

FIG. 2 Luminance

H/2 1 2 3

4 5 6 H

7 8
H/6

V/6 V/2

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 18 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

FIG.3 Response Time

The response time is defined as the following figure and shall be measured by switching the input signal for “any
level of grey(bright) “ and “any level of gray(dark)”.

Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)

0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%

90%
Photodetector
Output

10%
0%, 25%, 50%, 75%, 100%
Time

T γ (F) T γ (R)

FIG.4 Viewing Angle

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 19 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T315XW06 V5. In addition the figures in the
next page are detailed mechanical drawing of the LCD.

Horizontal 735.4mm

Vertical 433 mm
Outline Dimension
Depth 10.8 mm

Horizontal 705.4mm
Bezel Opening
Vertical 400mm

Horizontal 697.685mm
Active Display Area
Vertical 392.256mm

Weight 6,000 g (Typ.)

Surface Treatment AG, Haze=2%, 3H

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 20 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

Front View

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 21 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

Back View

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 22 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

6. Reliability Test Items

No. Test Item Q’ty Condition
1 High temperature storage test 3 60℃, 300hrs
2 Low temperature storage test 3 -20℃ , 300hrs

3 High temperature operation test 3 50℃ , 300hrs

4 Low temperature operation test 3 -5℃ , 300hrs

Wave form : random
Vibration level : 1.0G RMS
5 Vibration test (non-operation) 3 Bandwidth: 10-300Hz
Duration: X, Y, Z 10min
One time for each direction
Shock level: 50G
6 Shock test (non-operation) 3 Waveform: half sine wave, 11ms
Direction: ±X, ±Y, ±Z, One time each direction

Random wave (1.0G RMS, 10-200Hz)

7 Vibration test (With carton) 5
10mins/ each X,Y,Z axes

Height: 38.1 cm
8 Drop test (With carton) 5 1 corner, 3 edges, 6 surfaces
(ASTM-D5276)

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 23 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

7. International Standard
7-1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including electrical
Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical Standardization
(CENELEC), EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical
Business Equipment.

7-2 EMC
(4) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical
Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI), 1992
(5) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology
Equipment.” International Special committee on Radio Interference.
(6) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC), 1998

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 24 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

8. Packing
8-1 Definition of Label

Panel Label

*xxxxxxxxxxxx-xxxxxx*

AUO Internal Use

Panel Unique ID

AU Optronics
*xxxxxxxxxxxx-xxxxxx*

XXXXX Model NO: T315XW06 V.5 XXXXXXX

Manufactured XX/XX MADE IN XXXXX

AUO Internal Use Week Factory Location

Year AUO Internal Use

Green mark description

(1) For Pb Free Product, AUO will add for identification.

(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)

Carton Label

QTY : 5
T315XW06 V.5
97.31T15.5XX

*XXXXXX-XXXXXXXXXX*

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 25 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
8-2 Packing Method

1pc Module/ESD Bag Module

5pcs Modules

” H ” Tape

Cushion set

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 26 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
8-3 Pallet and Shipment Information

Specification Packing
Item
Quantity Dimension Weight (kg) Remark
1 Packing BOX 5pcs/box 828(L)mm*283W)mm*536(H)mm 36.5
2 Pallet 1 1150(L)mm*840(W)mm*132(H)mm 13
3 Boxes per Pallet 8 boxes/Pallet
4 Panels per Pallet 40 pcs/pallet

1150(L)mm*840(W)mm*1204(H)mm 305
Pallet after
5 N/A 1150(L)mm*840(W)mm*2408(H)mm
packing 610
Double Pallet

Corner angle Moisture-proof film

Stretch film

Label PET band

Corner angle

Pallet

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 27 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0

8. Precautions
Please pay attention to the followings when you use this TFT LCD module.

9-1 Mounting Precautions

(1) You must mount a module using holes arranged in four corners or four sides.

(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to module.
And the case on which a module is mounted should have sufficient strength so that external force is not
transmitted directly to the module.

(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.

(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit broken by
electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB pencil lead.
And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for
bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to
attach front/ rear polarizer. Do not use acetone, toluene and alcohol because they cause chemical damage
to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2 Operation Precautions

(1) The device listed in the product specification sheets was designed and manufactured for TV application
(2) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
V=±200mV(Over and under shoot voltage)
(3) Response time depends on the temperature. (In lower temperature, it becomes longer..)
(4) Brightness of module depends on the temperature. (In lower temperature, it becomes lower.) And in lower
temperature, response time (required time that brightness is stable after turned on) becomes longer.
(5) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(6) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(7) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done
by system manufacturers. Grounding and shielding methods may be important to minimize the interface.

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 28 / 29

Free Datasheet http://www.datasheet4u.net/
 T315XW06 V5 Product Specification
Rev. 0.0
9-3 Electrostatic Discharge Control
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wristband etc. And don’t touch interface pin directly.

9-4 Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5 Storage
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5 ℃ and 35℃ at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they be
stored in the container in which they were shipped.

9-6 Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off,
static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by
people who are electrically grounded and with well ion-blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel or its vestige is recognized, please wipe
them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 29 / 29

Free Datasheet http://www.datasheet4u.net/