Technical Data Sheet

Edition 2, 2007
Identification no.
02 01 02 02 000 0 000041
Version no. 0010
Sigunit®-P1 AF

®
Sigunit -P1 AF
Accelerating shotcrete admixture powder

Product ® ®
Description Sigunit -P1 AF is a readily soluble powder. Sigunit -P1 AF dissolved in water is a
liquid, alkali-free set accelerator for shotcrete. Its effectiveness depends on its mixing
Construction

ratio powder / water (its dilution / concentration).

®
Uses Sigunit -P1AF dissolved in water is suitable for both dry and wet spraying processes
and it is used for :

Support at the face whilst advancing tunnels and mines

Rock- and slope stabilisation

High quality lining shotcrete
®
Characteristics / Sigunit -P1 AF dissolved in water as a shotcrete set accelerator has the following
Advantages characteristics and advantages :

High early strength development

Alkali-free

Minimal strength loss of the accelerated concrete

No pollution of groundwater by leached out alkalis

Distinct reduction of rebound

Improves bond of shotcrete to rock and concrete thus facilitating overhead spraying

Distinct reduction of dust

Chloride-free, does not attack iron and steel

The supply in powder form has the following additional advantages :

High flexibility in use

Low cost of logistics

Longer shelf-life

Product Data
Form
Appearance / Colour Powder, whitish
Packaging 15 kg bag
One way big bag
Storage
Storage Conditions / 12 months from date of production if stored in original unopened, undamaged
Shelf Life Sealed containers, protected from direct sunlight and frost at temperatures between
5°C and +30°C.

Back

Table of Contents

1 ®
Sigunit -P1 AF 1/3
 Technical Data
Chemical Base Special inorganic materials.
Density 0.75 ± 0.95 kg/l (bulk density)
The density of the liquid set accelerator depends on the powder content and varies in
the range of 1.30 to 1.45 kg/l. The actual density must be determined on site.
pH Value ~ 3.0 dissolved in water.

System
Information
System Structure Aggregate grading for pumped concrete:
Usual mix with 8 mm aggregate size.
Concrete consistency (dependent on spraying equipment used):
Flow table spread size > 45 cm; w/c ratio < 0.48.
® ®
The use of an appropriate superplasticiser (such as Sika ViscoCrete SC-305 /
®
SikaTard -203) is essential.
Construction

Temperature of fresh concrete : > +15°C.

Application Details
Dosage The correct dosage must be determined by preliminary testing. For layer thickness of up
to 15 cm in one pass, dosage is between 3% and 6% of weight of binder.
® ®
Dosage of Sigunit -P1 AF is by peristaltic pump such as the Sika Aliva-403 pump.
Optimised mixing with the concrete mix is also essential.
®
The following Sika products are generally used for the basic shotcrete mix :
®
- Sika ViscoCrete SC-305
®
- SikaTard -203
®
- SikaTard -930
®
- SikaPump
® ® ®
- SikaFume -HR / -TU / Sikacrete -L / Sikacrete -PP1 TU

Application
Instructions
®
Mixing The liquid product mixed from Sigunit -P1 AF must be stored in suitable containers
made of plastic or stainless steel. Details of type and length of storage of mixed product
must always be agreed with the local Sika company.

Notes on Application / If thicker layers of shotcrete are to be applied, ensure that the temperature of the basic
Limitations concrete is not lower than +15°C. Lower temperatures require higher dosage of
accelerator.
The accelerator‘s effect depends on the cement content, the age and type of cement, on
the substrate and the shotcrete temperature as well as on the layer thickness and
spraying process. The w/c ratio of the basic concrete mix in the wet spraying process,
and the quantity of gauging water in the dry spraying process are also parameters
®
influencing the acceleration effect of dissolved Sigunit -P1 AF powder.
When using sulphate resistant cements strength development can be slower.
®
Sigunit -P1 AF is not compatible with alkaline shotcrete accelerators. Before using
®
Sigunit -P1 AF requires technically correct dosing and conveying / spraying
®
technology. Metal parts of the pump that come into direct contact with Sigunit -P1 AF
should be made of stainless steel. Contact your local Sika company for any additional
technical support required.

Notes All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.

2 ®
Sigunit -P1 AF 2/3
 Protective Measures To avoid allergic reactions, we recommend the use of protective gloves and facial mask.
In case of contact with skin or eyes, immediately wash thoroughly with plenty of water.
®
Sigunit -P1 AF should not be discharged into drains, waterways or the ground.
Local regulations and health and safety advice on the pacjaging labels must be
observed.

Important Notes Must be disposed of as hazardous waste in accordance with local regulations.
Please consult material safety data sheet. Residues of material must be removed
according to local regulations. Fully cured material can be disposed of as household
waster under agreement with the responsible local authorities.

Detailed health and safety information as well as detailed precautionary measures e.g.
physical, toxicological and ecological data can be obtained from the safety data sheet.

Legal Notes The information, and, in particular, the recommendations relating to the application and end-use of Sika
Construction

products, are given in good faith based on Sika’s current knowledge and experience of the product when
properly stored, handled and applied under normal conditions in accordances with Sika’s recommendations. In
practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect
of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship
whatsoever, can be inferred either from this information, or from any written recommendations, or from any
other advice offered. The user of the product must test the product’s suitability for the intended application and
purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties
must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will
be supplied on request.

PT. Sika Indonesia Branches

Jl. Raya Cibinong- Bekasi km. 20 Surabaya :
Limusnunggal- Cileungsi Puri Niaga Blok G No. 29, Jl. Raya Rungkut Menanggal 11, Surabaya
Tel : 031-8690202 ; Fax : 031-8682123
BOGOR 16820 - Indonesia
Medan :
Tel. +62 21 8230025 Jl. Pancing / Jl. Willem Iskandar No.75 & 75 A, Kec. Medan Tembung
Fax +62 21 8230026 Tel : 061- 6619500; Fax : (061) 6619400
Website : www.sika.co. id Batam :
e-mail: [email protected] Jl. Laksamana Bintan, Komp. Bumi Riau Makmur Blok E No.3, Sungai Panas
Tel : (0778) 424928; Fax : (0778) 450189

3 ®
Sigunit -P1 AF 3/3