Scribd
Upload
84 views4 pages

Type 6: Elastomer Bellows Seal

Uploaded by

Tommy Tran Nguyen
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
84 views4 pages

Type 6: Elastomer Bellows Seal

Uploaded by

Tommy Tran Nguyen
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

TYPE 6

6
Elastomer Bellows Seal

A – Seat Cup
B – Mating Ring (Seat)
C – Primary Ring D
D – Spring
E – Bellows
F – Drive Ring
G – Drive Sleeve C
H – Ferrules

Product Description Performance Capabilities


The Type 6 is a compact, unitized, single spring, ! Temperature:
elastomer bellows mechanical seal. -45°C to 205°C/-49°F to 400°F
! Type 6 Seals are designed for use in small centrifugal ! Pressure:
water pumps, deep and shallow well jet pumps, ID: 7.20 psi (0.5 bar)
swimming pool pumps and wastewater pumps. OD: up to 75 psig (5 bar g)
! Speed:
Design Features Up to 1000 fpm/5m/s
Up to 3600 rpm
! Seal Design:
One piece design enhances production line installation
and allows for ease of replacement. Industries Served
! Sealing Faces: ! Pool and Spa
Precision surface finish optimizes the service life and ! Industrial, Commercial and Residential Water Systems
reliability. Materials designed to meet the broadest
range of applications. ! Heating and Cooling
! Drive Ring:
Elastomer drive ring is pre-loaded to provide positive
drive and tight seal along the shaft.
! Flexible Bellows:
Full convolution elastomer bellows provides maximum
flexibility in compensating for shaft movement and
wear.
! Spring:
Coil spring and ferrules provide consistent face loading
through extreme working conditions.
TYPE 6
Elastomer Bellows Seal

Type 6 Typical Arrangement/Dimensional Data

.040 LG X 20 ∞ CHAM.

.010 R.
63

D5 63 D2
BORE ±.002
MIN. BORE
D4 D6
±.005
D3 D1
±.002 ALTERNATE O-RING SEAT
SHAFT

L3
L2 L1

Type 6 Dimensional Data (inches)


Seal Size/D1
(inches) D2 D3 D4 D5 D6 L1 L2 L3
0.375 1.000 0.812 1.062 1.312 0.750 0.312 0.656 0.250
0.437 1.000 0.812 1.062 1.312 0.750 0.312 0.656 0.250
0.500 1.000 0.812 1.062 1.312 0.750 0.312 0.656 0.250
0.562 1.250 0.937 1.218 1.500 0.937 0.406 0.718 0.343
0.625 1.250 0.937 1.218 1.500 0.937 0.406 0.718 0.343
0.687 1.375 1.062 1.343 1.625 1.062 0.406 0.718 0.343
0.750 1.375 1.062 1.343 1.625 1.062 0.406 0.718 0.343
0.875 1.625 1.312 1.687 2.000 1.312 0.437 0.812 0.375
1.000 1.625 1.312 1.687 2.000 1.312 0.437 0.812 0.375
TYPE 6
Elastomer Bellows Seal

Criteria for Installation

Shaft/Sleeve Limits

Surface Finish 32 to 63 Ra

Out of Roundness 0.051mm/.002"

Axial End Play ± 0.13mm/0.005"

Elastomer Temperature Limits

Buna-N (Nitrile)

Fluoroelastomer

Ethylene Propylene

Neoprene (Chloroprene)

–100 0 100 200 300 400 (°F)


–73 -18 38 93 149 205 (°C)
Temperature
TYPE 6
Elastomer Bellows Seal

Materials of Construction

SEAL COMPONENTS MATERIALS

Primary Ring Cranecarb (Phenolic Carbon Graphite)


(Washer) Carbon

Mating Ring Ceramic


(Seat) Silicon Carbide
Niresist

Hardware Stainless Steel

Secondary Seals Buna-N (Nitrile)


(Bellows, Drive Ring, Seat Cup, O-Ring) Neoprene® (Chloroprene)
Ethylene Propylene
Fluoroelastomer

Spring Stainless Steel

Neoprene is a registered trademark of DuPont.

Item. #
1 – Seat Cup
9
2 – Mating Ring (Seat)
3 – Primary Ring
4 – Spring
5 – Bellows 2
8
6 – Drive Ring
7 – Drive Sleeve
ALTERNATE O-RING SEAT
8 – Ferrules
9 – O-Ring 7 6 5 4 3 2 1

Asia Pacific Europe, Middle East, Africa Latin America North America
Singapore Slough, UK São Paulo, Brazil Morton Grove, Illinois USA
Tel: 65-861-1288 Tel: 44-1753-224000 Tel: 55-11-3049-9979 1-800-SEALING
Fax: 65-862-4117 Fax: 44-1753-224224 Fax: 55-11-3849-4511 Tel: 1-847-967-2400
Fax: 1-847-967-3915
For your nearest John Crane facility, please contact one of the locations above.
If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to their selection and use.
In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without prior notice. It is dangerous to smoke while handling
products made from PTFE. Old and new PTFE products must not be incinerated.
©2001 John Crane Print 9/01 www.johncrane.com ISO-Certified QS 9000 S-6

You might also like