0% found this document useful (0 votes)
98 views103 pages

STM32L100C6 STM32L100R8 STM32L100RB

Stm32 family

Uploaded by

tuna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
98 views103 pages

STM32L100C6 STM32L100R8 STM32L100RB

Stm32 family

Uploaded by

tuna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 103

STM32L100C6 STM32L100R8

STM32L100RB
Ultra-low-power 32-bit MCU ARM®-based Cortex®-M3,
128KB Flash, 10KB SRAM, 2KB EEPROM, LCD, USB, ADC, DAC
Datasheet −production data

Features
• Ultra-low-power platform
– 1.8 V to 3.6 V power supply LQFP64 UFQFPN48
– -40°C to 85°C temperature range 10 x 10 mm 7 x 7 mm

– 0.3 µA Standby mode (2 wakeup pins)


– 0.9 µA Standby mode + RTC • Memories
– 0.57 µA Stop mode (16 wakeup lines) – Up to 128 Kbytes of Flash memory with
– 1.2 µA Stop mode + RTC ECC
– 9 µA Low-power run mode – Up to 10 Kbytes of RAM
– 214 µA/MHz Run mode – Up to 2 Kbytes of true EEPROM with ECC
– 10 nA ultra-low I/O leakage – 20-byte backup register
– < 8 µs wakeup time • LCD Driver for up to 8x28 segments
® ® • Analog peripherals
• Core: 32-bit ARM Cortex -M3 CPU
– From 32 kHz up to 32 MHz max – 12-bit ADC 1 Msps up to 20 channels
– 1.25 DMIPS/MHz (Dhrystone 2.1) – 12-bit DAC 2 channels with output buffers
– Memory protection unit – Two ultra-low-power comparators
• Reset and supply management • Seven DMA controller channels
– Ultra-safe, low-power BOR (brownout • Eight communication interface peripherals
reset) with 5 selectable thresholds – One USB 2.0
– Ultra-low-power POR/PDR – Three USARTs (ISO 7816, IrDA)
– Programmable voltage detector (PVD) – Two SPIs (16 Mbit/s)
• Clock sources – Two I2Cs (SMBus/PMBus)
– 1 to 24 MHz crystal oscillator • Ten timers:
– 32 kHz oscillator for RTC with calibration – Six 16-bit timers with up to 4 IC/OC/PWM
– High-speed internal 16 MHz channels
– Internal low-power 37 kHz RC – Two 16-bit basic timers
– Internal multispeed low-power 65 kHz to – Two watchdog timers (independent and
4.2 MHz window)
– PLL for CPU clock and USB (48 MHz) • CRC calculation unit
• Pre-programmed bootloader • All packages ECOPACK®2
– USART supported
• Development support
– Serial wire debug supported
– JTAG supported
• Up to 51 fast I/Os (42 I/Os 5V tolerant), all
mappable on 16 external interrupt vectors

August 2017 DocID024295 Rev 6 1/103


This is information on a product in full production. www.st.com
Contents STM32L100C6 STM32L100R8/RB

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2 Ultra-low-power device continuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.2.1 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.2 Shared peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.3 Common system strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3 Functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1 Low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2 ARM® Cortex®-M3 core with MPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3 Reset and supply management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3.1 Power supply schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3.2 Power supply supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3.3 Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3.4 Boot modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.4 Clock management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.5 Low-power real-time clock and backup registers . . . . . . . . . . . . . . . . . . . 22
3.6 GPIOs (general-purpose inputs/outputs) . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.7 Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.8 DMA (direct memory access) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.9 LCD (liquid crystal display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.10 ADC (analog-to-digital converter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.10.1 Internal voltage reference (VREFINT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.11 DAC (digital-to-analog converter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.12 Ultra-low-power comparators and reference voltage . . . . . . . . . . . . . . . . 25
3.13 Routing interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.14 Timers and watchdogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.14.1 General-purpose timers (TIM2, TIM3, TIM4, TIM9, TIM10 and TIM11) . 26
3.14.2 Basic timers (TIM6 and TIM7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.14.3 SysTick timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Contents

3.14.4 Independent watchdog (IWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26


3.14.5 Window watchdog (WWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.15 Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.15.1 I²C bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.15.2 Universal synchronous/asynchronous receiver transmitter (USART) . . 27
3.15.3 Serial peripheral interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.15.4 Universal serial bus (USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.16 CRC (cyclic redundancy check) calculation unit . . . . . . . . . . . . . . . . . . . 28
3.17 Development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5 Memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1 Parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1.1 Minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1.2 Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1.3 Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1.4 Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1.5 Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.1.6 Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.1.7 Optional LCD power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.1.8 Current consumption measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.3.1 General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.3.2 Embedded reset and power control block characteristics . . . . . . . . . . . 45
6.3.3 Embedded internal reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.3.4 Supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.3.5 Wakeup time from Low-power mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.3.6 External clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.3.7 Internal clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.3.8 PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.3.9 Memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.3.10 EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.3.11 Electrical sensitivity characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

DocID024295 Rev 6 3/103


4
Contents STM32L100C6 STM32L100R8/RB

6.3.12 I/O current injection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70


6.3.13 I/O port characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6.3.14 NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.3.15 TIM timer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6.3.16 Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.3.17 12-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.3.18 DAC electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
6.3.19 Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.3.20 LCD controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

7 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
7.1 LQFP64 10 x 10 mm, 64-pin low-profile quad flat package information . . 91
7.2 UFQFPN48 7 x 7 mm, 0.5 mm pitch, package information . . . . . . . . . . . 94
7.3 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.3.1 Reference document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

8 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

4/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB List of tables

List of tables

Table 1. Ultra-low-power STM32L100C6 and STM32L100R8/RB device features


and peripheral counts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 2. Functionalities depending on the operating power supply range . . . . . . . . . . . . . . . . . . . . 14
Table 3. CPU frequency range depending on dynamic voltage scaling . . . . . . . . . . . . . . . . . . . . . . 15
Table 4. Working mode-dependent functionalities (from Run/active down to standby) . . . . . . . . . . 16
Table 5. Timer feature comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 6. Legend/abbreviations used in the pinout table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 7. STM32L100C6 and STM32L100R8/RB pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 8. Alternate function input/output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 9. Voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 10. Current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 11. Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 12. General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 13. Embedded reset and power control block characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 14. Embedded internal reference voltage calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 15. Embedded internal reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 16. Current consumption in Run mode, code with data processing running from Flash. . . . . . 49
Table 17. Current consumption in Run mode, code with data processing running from RAM . . . . . . 50
Table 18. Current consumption in Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 19. Current consumption in Low power run mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 20. Current consumption in Low power sleep mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 21. Typical and maximum current consumptions in Stop mode . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 22. Typical and maximum current consumptions in Standby mode . . . . . . . . . . . . . . . . . . . . . 55
Table 23. Peripheral current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 24. Low-power mode wakeup timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 25. High-speed external user clock characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 26. Low-speed external user clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 27. HSE oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 28. LSE oscillator characteristics (fLSE = 32.768 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 29. HSI oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 30. LSI oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 31. MSI oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 32. PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Table 33. RAM and hardware registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Table 34. Flash memory and data EEPROM characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Table 35. Flash memory, data EEPROM endurance and data retention . . . . . . . . . . . . . . . . . . . . . . 67
Table 36. EMS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 37. EMI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 38. ESD absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 39. Electrical sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Table 40. I/O current injection susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Table 41. I/O static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Table 42. Output voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 43. I/O AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 44. NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 45. TIMx characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Table 46. I2C characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 47. SCL frequency (fPCLK1= 32 MHz, VDD = VDD_I2C = 3.3 V). . . . . . . . . . . . . . . . . . . . . . . . 77

DocID024295 Rev 6 5/103


6
List of tables STM32L100C6 STM32L100R8/RB

Table 48. SPI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78


Table 49. USB startup time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 50. USB DC electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 51. USB: full speed electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 52. ADC clock frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 53. ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 54. ADC accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 55. Maximum source impedance RAIN max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 56. DAC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 57. Comparator 1 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Table 58. Comparator 2 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Table 59. LCD controller characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Table 60. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package mechanical data. . . . . . . . . . . 91
Table 61. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package mechanical data . . . . . . . . . . . . . . . . . . . . 95
Table 62. Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table 63. Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Table 64. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

6/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB List of figures

List of figures

Figure 1. Ultra-low-power STM32L100C6 and STM32L100R8/RB block diagram . . . . . . . . . . . . . . 12


Figure 2. Clock tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 3. STM32L100C6 and STM32L100R8/RB LQFP64 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 4. STM32L100C6 and STM32L100R8/RB UFQFPN48 pinout . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 5. Memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 6. Pin loading conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 7. Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 8. Power supply scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 9. Optional LCD power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 10. Current consumption measurement scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 11. High-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 12. Low-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 13. HSE oscillator circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 14. Typical application with a 32.768 kHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 15. I/O AC characteristics definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Figure 16. Recommended NRST pin protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 17. I2C bus AC waveforms and measurement circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 18. SPI timing diagram - slave mode and CPHA = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 19. SPI timing diagram - slave mode and CPHA = 1(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 20. SPI timing diagram - master mode(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 21. USB timings: definition of data signal rise and fall time . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 22. ADC accuracy characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 23. Typical connection diagram using the ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 24. Maximum dynamic current consumption on VDDA supply pin during ADC
conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 25. 12-bit buffered /non-buffered DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 26. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package outline . . . . . . . . . . . . . . . . . . 91
Figure 27. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package recommended footprint . . . . . 92
Figure 28. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package top view example . . . . . . . . . . 93
Figure 29. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Figure 30. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package recommended footprint . . . . . . . . . . . . . . . 95
Figure 31. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package top view example . . . . . . . . . . . . . . . . . . . 96
Figure 32. Thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

DocID024295 Rev 6 7/103


7
Introduction STM32L100C6 STM32L100R8/RB

1 Introduction

This datasheet provides the ordering information and mechanical device characteristics of
the STM32L100C6 and STM32L100R8/B ultra-low-power ARM® Cortex®-M3 based
microcontrollers product line.
The ultra-low-power STM32L100C6 and STM32L100R8/RB microcontroller family includes
devices in 2 different package types: 48 or 64 pins. Depending on the device chosen,
different sets of peripherals are included, the description below gives an overview of the
complete range of peripherals proposed in this family.
These features make the ultra-low-power STM32L100C6 and STM32L100R8/RB
microcontroller family suitable for a wide range of applications:
• Medical and handheld equipment
• Application control and user interface
• PC peripherals, gaming, GPS and sport equipment
• Alarm systems, Wired and wireless sensors, Video intercom
• Utility metering
This STM32L100C6 and STM32L100R8/B datasheet should be read in conjunction with the
STM32L1xxxx reference manual (RM0038). The document "Getting started with
STM32L1xxxx hardware development” AN3216 gives a hardware implementation overview.
Both documents are available from the STMicroelectronics website www.st.com.
For information on the ARM® Cortex®-M3 core please refer to the Cortex®-M3 Technical
Reference Manual, available from the ARM website.
Figure 1 shows the general block diagram of the device family.
Caution: This datasheet does not apply to:
– STM32L100C6-A
– STM32L100R8-A
– STM32L100RB-A
covered by a separate datasheet.

8/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Description

2 Description

The ultra-low-power STM32L100C6 and STM32L100R8/RB devices incorporate the


connectivity power of the universal serial bus (USB) with the high-performance ARM®
Cortex®-M3 32-bit RISC core operating at a frequency of 32 MHz (33.3 DMIPS), a memory
protection unit (MPU), high-speed embedded memories (Flash memory up to 128 Kbytes
and RAM up to 10 Kbytes) and an extensive range of enhanced I/Os and peripherals
connected to two APB buses.
All the devices offer a 12-bit ADC, 2 DACs and 2 ultra-low-power comparators, six general-
purpose 16-bit timers and two basic timers, which can be used as time bases.
Moreover, the STM32L100C6 and STM32L100R8/RB devices contain standard and
advanced communication interfaces: up to two I2Cs and SPIs, three USARTs and a USB.
They also include a real-time clock with sub-second counting and a set of backup registers
that remain powered in Standby mode.
Finally, the integrated LCD controller has a built-in LCD voltage generator that allows to
drive up to 8 multiplexed LCDs with contrast independent of the supply voltage.
The ultra-low-power STM32L100C6 and STM32L100R8/RB devices operate from a 1.8 to
3.6 V power supply. They are available in the -40 to +85 °C temperature range. A
comprehensive set of power-saving modes allows the design of low-power applications.

DocID024295 Rev 6 9/103


39
Description STM32L100C6 STM32L100R8/RB

2.1 Device overview


Table 1. Ultra-low-power STM32L100C6 and STM32L100R8/RB device features
and peripheral counts
Peripheral STM32L100C6 STM32L100R8/B

Flash (Kbytes) 32 64 128

Data EEPROM (Kbytes) 2

RAM (Kbytes) 4 8 10

General-
6
purpose
Timers
Basic 2

SPI 2

I2C 2
Communication
interfaces
USART 3

USB 1

GPIOs 37 51

12-bit synchronized ADC 1 1


Number of channels 14 channels 20 channels

12-bit DAC 2
Number of channels 2

LCD 4x32
4x18
COM x SEG 8x28

Comparator 2

Max. CPU frequency 32 MHz

Operating voltage 1.8 V to 3.6 V

Ambient temperatures: –40 to +85 °C


Operating temperatures
Junction temperature: -40 to +105°C

Packages UFQFPN48 LQFP64

10/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Description

2.2 Ultra-low-power device continuum


The ultra-low-power family offers a large choice of cores and features. From a proprietary 8-
bit core up to the Cortex-M3, including the Cortex-M0+, the STM8Lx and STM32Lx series
offer the best range of choices to meet your requirements in terms of ultra-low-power
features. The STM32 Ultra-low-power series is an ideal fit for applications like gas/water
meters, keyboard/mouse, or wearable devices for fitness and healthcare. Numerous built-in
features like LCD drivers, dual-bank memory, low-power Run mode, op-amp, AES-128bit,
DAC, crystal-less USB and many others, allow to build highly cost-optimized applications by
reducing the BOM.
Note: STMicroelectronics as a reliable and long-term manufacturer ensures as much as possible
the pin-to-pin compatibility between any STM8Lx and STM32Lx devices and between any of
the STM32Lx and STM32Fx series. Thanks to this unprecedented scalability, your existing
applications can be upgraded to respond to the latest market features and efficiency
demand.

2.2.1 Performance
All families incorporate highly energy-efficient cores with both Harvard architecture and
pipelined execution: advanced STM8 core for STM8L families and ARM Cortex-M3 core for
STM32L family. In addition specific care for the design architecture has been taken to
optimize the mA/DMIPS and mA/MHz ratios.
This allows the ultra-Low-power performance to range from 5 up to 33.3 DMIPs.

2.2.2 Shared peripherals


STM8L15xxx and STM32L1xxxx share identical peripherals which ensure a very easy
migration from one family to another:
• Analog peripherals: ADC, DAC and comparators
• Digital peripherals: RTC and some communication interfaces

2.2.3 Common system strategy


To offer flexibility and optimize performance, the STM8L15xxx and STM32L1xxxx families
use a common architecture:
• Common power supply range from 1.8 V to 3.6 V
• Architecture optimized to reach ultra-low consumption both in low-power modes and
Run mode
• Fast startup strategy from low-power modes
• Flexible system clock
• Ultra-safe reset: same reset strategy including power-on reset, power-down reset,
brownout reset and programmable voltage detector.

2.2.4 Features
ST ultra-low-power continuum also lies in feature compatibility:
• More than 10 packages with pin count from 20 to 144 pins and size down to 3 x 3 mm
• Memory density ranging from 4 to 512 Kbytes

DocID024295 Rev 6 11/103


39
Functional overview STM32L100C6 STM32L100R8/RB

3 Functional overview

Figure 1 shows the block diagram.

Figure 1. Ultra-low-power STM32L100C6 and STM32L100R8/RB block diagram

6 $$
*4!'37 6#/2% 0/7%2
PBUS 6$$6TO6
6/,42%' 6 33
.*4234 &RUWH[0&38

)ODVK REO
*4$)

,QWHUIDFH
)BUS
*4#+37#,+ +"&LASH
*4-337$!4 &MAX-(Z +"DATA%%02/-
$BUS

%XV0DWUL[
*4$/
AS!& -05 3YSTEM
5$0
.6)#
.%
6$$!
'0$-! /3#?).
!("0#,+
CHANNELS !0"0#,+ 0,, 84!,/3# /3#?/54
(#,+ CLOCK  -(Z
&#,+ MANAGEMENT
6$$!
.234 3UPPLY 2#(3
MONITORING
0OWERRESET 2#-3
62%&/54054 %2595(),17 )7$'
2#,3
$+%)PD[ 0+]

6$$! )N T 6$$! 3TANDBYINTERFACE


06$
633! /3#?).
#OMP 84! ,  K(Z
/3#?/54
#/-0?). ). #OMP
24# 24#?!&).
3RZHUXS !75 24#?/54 24#?43
3RZHUGRZQ "ACKUP 24#?4!-0
REGISTER
0!;= '0)/!
"ACKUPINTERFACE

0";= '0)/"
9/&'

/&'VWHSXS 6,#$6TO6
0#;= '0)/# CONVERTER

0$;= '0)/$ 4)- #HANNELS

0(;= 4)- #HANNELS


'0)/(

4)- #HANNELS

28 48 #43 243


$+%" $+%
!("  53!24 3MART#ARDAS!&
$3% $3%
%84)4 28 48 #43 243
!& 53!24 3MART#ARDAS!&
7+50

-/3) -)3/ -/3) -)3/ 3#+ .33


$3%)PD[ 0+]

30)  30) !S!&


3#+ .33AS!&

28 48 #43 243 3#, 3$!


53!24 ,&
3MART#ARDAS!& AS!&
$3%)PD[ 0+]

3#, 3$! 3-"US 0-"US


6$$! ,& AS!&

!&  BIT!$# )&


53"?$0
86%5$0% 86%)6GHYLFH 53"?$-

4EMPSENSOR 77$'
3%'X
,#$XX
#/-X
'ENERALPURPOSE
TIMERS
"!3)#4)-%23 6$$!
#HANNELS 4)-
$!#?/54AS
4)-  BIT $!# !&
#HANNEL )&
)&
4)- $!#?/54AS
4)-  BIT $!#
!&
#HANNEL 4)-

06Y9

1. AF = alternate function on I/O port pin.

12/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

3.1 Low-power modes


The ultra-low-power STM32L100C6 and STM32L100R8/RB devices support dynamic
voltage scaling to optimize its power consumption in run mode. The voltage from the internal
low-drop regulator that supplies the logic can be adjusted according to the system’s
maximum operating frequency and the external voltage supply:
• In Range 1 (VDD range limited to 2.0-3.6 V), the CPU runs at up to 32 MHz (refer to
Table 16 for consumption).
• In Range 2 (full VDD range), the CPU runs at up to 16 MHz (refer to Table 16 for
consumption)
• In Range 3 (full VDD range), the CPU runs at up to 4 MHz (generated only with the
multispeed internal RC oscillator clock source). Refer to Table 16 for consumption.
Seven low-power modes are provided to achieve the best compromise between low-power
consumption, short startup time and available wakeup sources:
• Sleep mode
In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can
wake up the CPU when an interrupt/event occurs.
Sleep mode power consumption: refer to Table 18.
• Low-power Run mode
This mode is achieved with the multispeed internal (MSI) RC oscillator set to the MSI
range 0 or MSI range 1 clock range (maximum 131 kHz), execution from SRAM or
Flash memory, and internal regulator in low-power mode to minimize the regulator's
operating current. In the low-power Run mode, the clock frequency and the number of
enabled peripherals are both limited.
Low-power Run mode consumption: refer to Table 19.
• Low-power Sleep mode
This mode is achieved by entering the Sleep mode with the internal voltage regulator in
low-power mode to minimize the regulator’s operating current. In the low-power Sleep
mode, both the clock frequency and the number of enabled peripherals are limited; a
typical example would be to have a timer running at 32 kHz.
When wakeup is triggered by an event or an interrupt, the system reverts to the run
mode with the regulator on.
Low-power Sleep mode consumption: refer to Table 20.
• Stop mode with RTC
Stop mode achieves the lowest power consumption while retaining the RAM and
register contents and real time clock. All clocks in the VCORE domain are stopped, the
PLL, MSI RC, HSI RC and HSE crystal oscillators are disabled. The LSE or LSI is still
running. The voltage regulator is in the low-power mode.
The device can be woken up from Stop mode by any of the EXTI line, in 8 µs. The EXTI
line source can be one of the 16 external lines. It can be the PVD output, the
Comparator 1 event or Comparator 2 event (if internal reference voltage is on), it can
be the RTC alarm(s), the USB wakeup, the RTC tamper events, the RTC timestamp
event or the RTC wakeup.
• Stop mode without RTC
Stop mode achieves the lowest power consumption while retaining the RAM and
register contents. All clocks are stopped, the PLL, MSI RC, HSI and LSI RC, LSE and
HSE crystal oscillators are disabled. The voltage regulator is in the low-power mode.
The device can be woken up from Stop mode by any of the EXTI line, in 8 µs. The EXTI

DocID024295 Rev 6 13/103


39
Functional overview STM32L100C6 STM32L100R8/RB

line source can be one of the 16 external lines. It can be the PVD output, the
Comparator 1 event or Comparator 2 event (if internal reference voltage is on). It can
also be wakened by the USB wakeup.
Stop mode consumption: refer to Table 21.
• Standby mode with RTC
Standby mode is used to achieve the lowest power consumption and real time clock.
The internal voltage regulator is switched off so that the entire VCORE domain is
powered off. The PLL, MSI RC, HSI RC and HSE crystal oscillators are also switched
off. The LSE or LSI is still running. After entering Standby mode, the RAM and register
contents are lost except for registers in the Standby circuitry (wakeup logic, IWDG,
RTC, LSI, LSE Crystal 32K osc, RCC_CSR).
The device exits Standby mode in 60 µs when an external reset (NRST pin), an IWDG
reset, a rising edge on one of the two WKUP pins, RTC alarm (Alarm A or Alarm B),
RTC tamper event, RTC timestamp event or RTC Wakeup event occurs.
• Standby mode without RTC
Standby mode is used to achieve the lowest power consumption. The internal voltage
regulator is switched off so that the entire VCORE domain is powered off. The PLL, MSI,
RC, HSI and LSI RC, HSE and LSE crystal oscillators are also switched off. After
entering Standby mode, the RAM and register contents are lost except for registers in
the Standby circuitry (wakeup logic, IWDG, RTC, LSI, LSE Crystal 32K osc,
RCC_CSR).
The device exits Standby mode in 60 µs when an external reset (NRST pin) or a rising
edge on one of the two WKUP pin occurs.
Standby mode consumption: refer to Table 22.
Note: The RTC, the IWDG, and the corresponding clock sources are not stopped by entering the
Stop or Standby mode.

Table 2. Functionalities depending on the operating power supply range


Functionalities depending on the operating power supply range(1)
Operating power
supply range DAC and ADC
USB Dynamic voltage scaling range
operation

Conversion time Range 2 or


VDD = 1.8 to 2.0 V Not functional
up to 500 Ksps Range 3

Conversion time
VDD = 2.0 to 2.4 V Functional(2) Range 1, Range 2 or Range 3
up to 500 Ksps

Conversion time
VDD = 2.4 to 3.6 V Functional(2) Range 1, Range 2 or Range 3
up to 1 Msps
1. The GPIO speed also depends from VDD voltage and the user has to refer to Table 43: I/O AC
characteristics for more information about I/O speed.
2. Should be USB-compliant from I/O voltage standpoint, the minimum VDD is 3.0 V.

14/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

Table 3. CPU frequency range depending on dynamic voltage scaling

CPU frequency range Dynamic voltage scaling range

16 MHz to 32 MHz (1ws)


Range 1
32 kHz to 16 MHz (0ws)
8 MHz to 16 MHz (1ws)
Range 2
32 kHz to 8 MHz (0ws)
2.1 MHz to 4.2 MHz (1ws)
Range 3
32 kHz to 2.1 MHz (0ws)

DocID024295 Rev 6 15/103


39
Functional overview STM32L100C6 STM32L100R8/RB

Table 4. Working mode-dependent functionalities (from Run/active down to standby)


Stop Standby
Low- Low-
Ips Run/Active Sleep power power
Wakeup Wakeup
Run Sleep
capability capability

CPU Y - Y - - - - -
Flash Y Y Y - - - - -
RAM Y Y Y Y Y - - -
Backup Registers Y Y Y Y Y - Y -
EEPROM Y Y Y Y Y - - -
Brown-out reset
Y Y Y Y Y Y Y -
(BOR)
DMA Y Y Y Y - - - -
Programmable
Voltage Detector Y Y Y Y Y Y Y -
(PVD)
Power On Reset
Y Y Y Y Y Y Y -
(POR)
Power Down Rest
Y Y Y Y Y - Y -
(PDR)
High Speed
Y Y - - - - - -
Internal (HSI)
High Speed
Y Y - - - - - -
External (HSE)
Low Speed Internal
Y Y Y Y Y - Y -
(LSI)
Low Speed
Y Y Y Y Y - Y -
External (LSE)
Multi-Speed
Y Y Y Y - - - -
Internal (MSI)
Inter-Connect
Y Y Y Y - - - -
Controller
RTC Y Y Y Y Y Y Y -
RTC Tamper Y Y Y Y Y Y Y Y
Auto Wakeup
Y Y Y Y Y Y Y Y
(AWU)
LCD Y Y Y Y Y - - -
USB Y Y - - - Y - -
(1)
USART Y Y Y Y Y - -
SPI Y Y Y Y - - - -
(1)
I2C Y Y - - - - -
ADC Y Y - - - - - -

16/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

Table 4. Working mode-dependent functionalities (from Run/active down to standby) (continued)


Stop Standby
Low- Low-
Ips Run/Active Sleep power power
Wakeup Wakeup
Run Sleep
capability capability

DAC Y Y Y Y Y - - -
Comparators Y Y Y Y Y Y - -
16-bit Timers Y Y Y Y - - - -
IWDG Y Y Y Y Y Y Y Y
WWDG Y Y Y Y - - - -
Systick Timer Y Y Y Y - - - -
GPIOs Y Y Y Y Y Y - 2 pins
Wakeup time to
0 µs 0.4 µs 3 µs 46 µs < 8 µs 58 µs
Run mode
0.65 µA (No 0.3 µA (No RTC)
RTC) VDD=1.8 V VDD=1.8 V
1.4 µA (with 1 µA (with RTC)
Consumption Down to Down to RTC) V =1.8 V VDD=1.8 V
Down to Down to DD
VDD=1.8V to 3.6V 214 µA/MHz 50 µA/MHz
9 µA 4.4 µA 0.65 µA (No 0.3 µA (No RTC)
(Typ) (from Flash) (from Flash)
RTC) VDD=3.0 V VDD=3.0 V
1.6 µA (with 1.3 µA (with
RTC) VDD=3.0 V RTC) VDD=3.0 V
1. The startup on communication line wakes the CPU which was made possible by an EXTI, this induces a delay before
entering run mode.

3.2 ARM® Cortex®-M3 core with MPU


The ARM® Cortex®-M3 processor is the industry leading processor for embedded systems.
It has been developed to provide a low-cost platform that meets the needs of MCU
implementation, with a reduced pin count and low-power consumption, while delivering
outstanding computational performance and an advanced system response to interrupts.
The ARM® Cortex®-M3 32-bit RISC processor features exceptional code-efficiency,
delivering the high-performance expected from an ARM core in the memory size usually
associated with 8- and 16-bit devices.
The memory protection unit (MPU) improves system reliability by defining the memory
attributes (such as read/write access permissions) for different memory regions. It provides
up to eight different regions and an optional predefined background region.
Owing to its embedded ARM core, the STM32L100C6 and STM32L100R8/RB devices are
compatible with all ARM tools and software.

DocID024295 Rev 6 17/103


39
Functional overview STM32L100C6 STM32L100R8/RB

Nested vectored interrupt controller (NVIC)


The ultra-low-power STM32L100C6 and STM32L100R8/RB devices embed a nested
vectored interrupt controller able to handle up to 45 maskable interrupt channels (not
including the 16 interrupt lines of Cortex-M3) and 16 priority levels.
• Closely coupled NVIC gives low-latency interrupt processing
• Interrupt entry vector table address passed directly to the core
• Closely coupled NVIC core interface
• Allows early processing of interrupts
• Processing of late arriving, higher-priority interrupts
• Support for tail-chaining
• Processor state automatically saved on interrupt entry, and restored on interrupt exit,
with no instruction overhead
This hardware block provides flexible interrupt management features with minimal interrupt
latency.

3.3 Reset and supply management

3.3.1 Power supply schemes


• VDD = 1.8 to 3.6 V: external power supply for I/Os and the internal regulator.
Provided externally through VDD pins.
• VSSA, VDDA = 1.8 to 3.6 V: external analog power supplies for ADC, reset blocks, RCs
and PLL.
VDDA and VSSA must be connected to VDD and VSS, respectively.

3.3.2 Power supply supervisor


The device has an integrated ZEROPOWER power-on reset (POR)/power-down reset
(PDR) that can be coupled with a brownout reset (BOR) circuitry.
BOR is activated at power-on and the device operates between 1.8 V and 3.6 V.
After the VDD threshold is reached, the option byte loading process starts, either to confirm
or modify default thresholds, or to disable the BOR permanently.
BOR ensures proper operation starting from 1.8 V whatever the power ramp-up phase
before it reaches 1.8 V.

18/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

Five BOR thresholds are available through option bytes, starting from 1.8 V to 3 V. To
reduce the power consumption in Stop mode, it is possible to automatically switch off the
internal reference voltage (VREFINT) in Stop mode. The device remains in reset mode when
VDD is below a specified threshold, VPOR/PDR or VBOR, without the need for any external
reset circuit.
The device features an embedded programmable voltage detector (PVD) that monitors the
VDD/VDDA power supply and compares it to the VPVD threshold. This PVD offers 7 different
levels between 1.85 V and 3.05 V, chosen by software, with a step around 200 mV. An
interrupt can be generated when VDD/VDDA drops below the VPVD threshold and/or when
VDD/VDDA is higher than the VPVD threshold. The interrupt service routine can then generate
a warning message and/or put the MCU into a safe state. The PVD is enabled by software.

3.3.3 Voltage regulator


The regulator has three operation modes: main (MR), low-power (LPR) and power down.
• MR is used in Run mode (nominal regulation)
• LPR is used in the Low-power run, Low-power sleep and Stop modes
• Power down is used in Standby mode. The regulator output is high impedance, the
kernel circuitry is powered down, inducing zero consumption but the contents of the
registers and RAM are lost are lost except for the standby circuitry (wakeup logic,
IWDG, RTC, LSI, LSE crystal 32K osc, RCC_CSR).

3.3.4 Boot modes


At startup, boot pins are used to select one of three boot options:
• Boot from Flash memory
• Boot from System Memory
• Boot from embedded RAM
The boot loader is located in System Memory. It is used to reprogram the Flash memory by
using USART1 or USART2. See the application note “STM32 microcontroller system
memory boot mode” (AN2606) for details.
The HSI oscillator is to be calibrated to +/-1% before using of the bootloader.

DocID024295 Rev 6 19/103


39
Functional overview STM32L100C6 STM32L100R8/RB

3.4 Clock management


The clock controller distributes the clocks coming from different oscillators to the core and
the peripherals. It also manages clock gating for low-power modes and ensures clock
robustness. It features:
• Clock prescaler: to get the best trade-off between speed and current consumption, the
clock frequency to the CPU and peripherals can be adjusted by a programmable
prescaler
• Safe clock switching: clock sources can be changed safely on the fly in run mode
through a configuration register.
• Clock management: to reduce power consumption, the clock controller can stop the
clock to the core, individual peripherals or memory.
• Master clock source: three different clock sources can be used to drive the master
clock:
– 1-24 MHz high-speed external crystal (HSE), that can supply a PLL
– 16 MHz high-speed internal RC oscillator (HSI), trimmable by software, that can
supply a PLL
– Multispeed internal RC oscillator (MSI), trimmable by software, able to generate 7
frequencies (65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.1 MHz, 4.2 MHz)
with a consumption proportional to speed, down to 750 nA typical. When a
32.768 kHz clock source is available in the system (LSE), the MSI frequency can
be trimmed by software down to a ±0.5% accuracy.
• Auxiliary clock source: two ultra-low-power clock sources that can be used to drive
the LCD controller and the real-time clock:
– 32.768 kHz low-speed external crystal (LSE)
– 37 kHz low-speed internal RC (LSI), also used to drive the independent watchdog.
The LSI clock can be measured using the high-speed internal RC oscillator for
greater precision.
• RTC and LCD clock sources: the LSI, LSE or HSE sources can be chosen to clock
the RTC and the LCD, whatever the system clock.
• USB clock source: the embedded PLL has a dedicated 48 MHz clock output to supply
the USB interface.
• Startup clock: after reset, the microcontroller restarts by default with an internal
2.1 MHz clock (MSI). The prescaler ratio and clock source can be changed by the
application program as soon as the code execution starts.
• Clock security system (CSS): this feature can be enabled by software. If a HSE clock
failure occurs, the master clock is automatically switched to HSI and a software
interrupt is generated if enabled.
• Clock-out capability (MCO: microcontroller clock output): it outputs one of the
internal clocks for external use by the application.
Several prescalers allow the configuration of the AHB frequency, the high-speed APB
(APB2) and the low-speed APB (APB1) domains. The maximum frequency of the AHB and
the APB domains is 32 MHz. See Figure 2 for details on the clock tree.

20/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

Figure 2. Clock tree

-3)2#
-3)

!$##,+
TO!$#

0ERIPHERALCLOCK
ENABLE
-(Z

(3)2# (3)
-(Z
0,,6#/ 53"#,+
TO53"INTERFACE 37
0,,32#
0,,-5, 0,,$)6
X X X X (3)
   393#,+  -(Z MAX
X X X

/3#?/54 X X 0,,#,+
 -(Z
(3%/3# (3%
/3#?).
#33

(#,+
-(ZMAX TO!("BUS CORE
#LOCK MEMORYAND$-!
%NABLE
 TO#ORTEX3YSTEMTIMER
&#,+#ORTEX
FREERUNNINGCLOCK
!(" !0"
-(ZMAX 0#,+
0RESCALER 0RESCALER
TO!0"
       PERIPHERALS
0ERIPHERAL#LOCK
%NABLE

)F!0"PRESCALER X TO4)-   AND


ELSEX 4)-X#,+
0ERIPHERAL#LOCK
%NABLE
!0" -(ZMAX 0#,+
0RESCALER
     PERIPHERALSTO!0"
0ERIPHERAL#LOCK
%NABLE

)F!0"PRESCALER X TO4)-  AND


ELSEX 4)-X#,+
0ERIPHERAL#LOCK
TO %NABLE
  4IMER  %42
 

/3#?). TO24#
,3%/3# ,3%
K(Z 24##,+
/3#?/54 TO,#$
24#3%,;=

TO)NDEPENDENT7ATCHDOG)7$'
,3)2# ,3)
K(Z )7$'#,+
,EGEND
(3%(IGH SPEEDEXTERNALCLOCKSIGNAL
393#,+
(3) (3) (IGH SPEEDINTERNALCLOCKSIGNAL
   -3) ,3),OW SPEEDINTERNALCLOCKSIGNAL
-#/
  (3%
0,,#,+ ,3%,OW SPEEDEXTERNALCLOCKSIGNAL
,3) -3)-ULTISPEEDINTERNALCLOCKSIGNAL

,3%
-#/3%,
AIC

DocID024295 Rev 6 21/103


39
Functional overview STM32L100C6 STM32L100R8/RB

3.5 Low-power real-time clock and backup registers


The real-time clock (RTC) is an independent BCD timer/counter. Dedicated registers contain
the sub-second, second, minute, hour (12/24 hour), week day, date, month, year, in BCD
(binary-coded decimal) format. Correction for 28, 29 (leap year), 30, and 31 day of the
month are made automatically. The RTC provides two programmable alarms and
programmable periodic interrupts with wakeup from Stop and Standby modes.
The programmable wakeup time ranges from 120 µs to 36 hours.
The RTC can be calibrated with an external 512 Hz output, and a digital compensation
circuit helps reduce drift due to crystal deviation. The RTC can also be automatically
corrected with a 50/60Hz stable power line.
The RTC calendar can be updated on the fly down to sub second precision, which enables
network system synchronization. A time stamp can record an external event occurrence,
and generates an interrupt.
There are five 32-bit backup registers provided to store 20 bytes of user application data.
They are cleared in case of tamper detection. Three pins can be used to detect tamper
events. A change on one of these pins can reset backup register and generate an interrupt.
To prevent false tamper event, like ESD event, these three tamper inputs can be digitally
filtered.

3.6 GPIOs (general-purpose inputs/outputs)


Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as
input (with or without pull-up or pull-down) or as peripheral alternate function. Most of the
GPIO pins are shared with digital or analog alternate functions, and can be individually
remapped using dedicated AFIO registers. All GPIOs are high current capable. The
alternate function configuration of I/Os can be locked if needed following a specific
sequence in order to avoid spurious writing to the I/O registers. The I/O controller is
connected to the AHB with a toggling speed of up to 16 MHz.

External interrupt/event controller (EXTI)


The external interrupt/event controller consists of 23 edge detector lines used to generate
interrupt/event requests. Each line can be individually configured to select the trigger event
(rising edge, falling edge, both) and can be masked independently. A pending register
maintains the status of the interrupt requests. The EXTI can detect an external line with a
pulse width shorter than the Internal APB2 clock period. Up to 51 GPIOs can be connected
to the 16 external interrupt lines. The 7 other lines are connected to RTC, PVD, USB or
Comparator events.

22/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

3.7 Memories
The STM32L100C6 and STM32L100R8/RB devices have the following features:
• Up to 10 Kbytes of embedded RAM accessed (read/write) at CPU clock speed with 0
wait states. With the enhanced bus matrix, operating the RAM does not lead to any
performance penalty during accesses to the system bus (AHB and APB buses).
• The non-volatile memory is divided into three arrays:
– 32, 64 or 128 Kbytes of embedded Flash program memory
– 2 Kbytes of data EEPROM
– Options bytes
The options bytes are used to write-protect the memory (with 4 Kbytes granularity)
and/or readout-protect the whole memory with the following options:
– Level 0: no readout protection
– Level 1: memory readout protection, the Flash memory cannot be read from or
written to if either debug features are connected or boot in RAM is selected
– Level 2: chip readout protection, debug features (Cortex-M3 JTAG and serial wire)
and boot in RAM selection disabled (JTAG fuse)
The whole non-volatile memory embeds the error correction code (ECC) feature.

3.8 DMA (direct memory access)


The flexible 7-channel, general-purpose DMA is able to manage memory-to-memory,
peripheral-to-memory and memory-to-peripheral transfers. The DMA controller supports
circular buffer management, avoiding the generation of interrupts when the controller
reaches the end of the buffer.
Each channel is connected to dedicated hardware DMA requests, with software trigger
support for each channel. Configuration is done by software and transfer sizes between
source and destination are independent.
The DMA can be used with the main peripherals: SPI, I2C, USART, general-purpose timers
and ADC.

3.9 LCD (liquid crystal display)


The LCD drives up to 8 common terminals and 32 segment terminals to drive up to 224
pixels.
• Internal step-up converter to guarantee functionality and contrast control irrespective of
VDD. This converter can be deactivated, in which case the VLCD pin is used to provide
the voltage to the LCD
• Supports static, 1/2, 1/3, 1/4 and 1/8 duty
• Supports static, 1/2, 1/3 and 1/4 bias
• Phase inversion to reduce power consumption and EMI
• Up to 8 pixels can be programmed to blink
• Unneeded segments and common pins can be used as general I/O pins
• LCD RAM can be updated at any time owing to a double-buffer
• The LCD controller can operate in Stop mode

DocID024295 Rev 6 23/103


39
Functional overview STM32L100C6 STM32L100R8/RB

3.10 ADC (analog-to-digital converter)


A 12-bit analog-to-digital converters is embedded into STM32L100C6 and
STM32L100R8/RB devices with up to 20 external channels, performing conversions in
single-shot or scan mode. In scan mode, automatic conversion is performed on a selected
group of analog inputs.
The ADC can be served by the DMA controller.
An analog watchdog feature allows very precise monitoring of the converted voltage of one,
some or all selected channels. An interrupt is generated when the converted voltage is
outside the programmed thresholds.
The events generated by the general-purpose timers (TIMx) can be internally connected to
the ADC start trigger and injection trigger, to allow the application to synchronize A/D
conversions and timers. An injection mode allows high priority conversions to be done by
interrupting a scan mode which runs in as a background task.
The ADC includes a specific low-power mode. The converter is able to operate at maximum
speed even if the CPU is operating at a very low frequency and has an auto-shutdown
function. The ADC’s runtime and analog front-end current consumption are thus minimized
whatever the MCU operating mode.

3.10.1 Internal voltage reference (VREFINT)


The internal voltage reference (VREFINT) provides a stable (bandgap) voltage output for the
ADC and Comparators. VREFINT is internally connected to the ADC_IN17 input channel. It
enables accurate monitoring of the VDD value. The precise voltage of VREFINT is individually
measured for each part by ST during production test and stored in the system memory area.
It is accessible in read-only mode see Table 15: Embedded internal reference voltage.

3.11 DAC (digital-to-analog converter)


The two 12-bit buffered DAC channels can be used to convert two digital signals into two
analog voltage signal outputs. The chosen design structure is composed of integrated
resistor strings and an amplifier in non-inverting configuration.
This dual digital Interface supports the following features:
• two DAC converters: one for each output channel
• left or right data alignment in 12-bit mode
• synchronized update capability
• noise-wave generation
• triangular-wave generation
• dual DAC channels’ independent or simultaneous conversions
• DMA capability for each channel (including the underrun interrupt)
• external triggers for conversion
Eight DAC trigger inputs are used in the STM32L100C6 and STM32L100R8/RB devices.
The DAC channels are triggered through the timer update outputs that are also connected
to different DMA channels.

24/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

3.12 Ultra-low-power comparators and reference voltage


The STM32L100C6 and STM32L100R8/RB devices embed two comparators sharing the
same current bias and reference voltage. The reference voltage can be internal or external
(coming from an I/O).
• one comparator with fixed threshold
• one comparator with rail-to-rail inputs, fast or slow mode. The threshold can be one of
the following:
– DAC output
– External I/O
– Internal reference voltage (VREFINT) or VREFINT submultiple (1/4, 1/2, 3/4)
Both comparators can wake up from Stop mode, and be combined into a window
comparator.
The internal reference voltage is available externally via a low-power / low-current output
buffer (driving current capability of 1 µA typical).

3.13 Routing interface


This interface controls the internal routing of I/Os to TIM2, TIM3, TIM4 and to the
comparator and reference voltage output.

3.14 Timers and watchdogs


The ultra-low-power STM32L100C6 and STM32L100R8/RB devices include six general-
purpose timers, two basic timers and two watchdog timers.
Table 5 compares the features of the general-purpose and basic timers.

Table 5. Timer feature comparison


Counter Counter Prescaler DMA request Capture/compare Complementary
Timer
resolution type factor generation channels outputs

TIM2, Up, Any integer


TIM3, 16-bit down, between 1 Yes 4 No
TIM4 up/down and 65536
Up, Any integer
TIM9 16-bit down, between 1 No 2 No
up/down and 65536
Any integer
TIM10,
16-bit Up between 1 No 1 No
TIM11
and 65536
Any integer
TIM6,
16-bit Up between 1 Yes 0 No
TIM7
and 65536

DocID024295 Rev 6 25/103


39
Functional overview STM32L100C6 STM32L100R8/RB

3.14.1 General-purpose timers (TIM2, TIM3, TIM4, TIM9, TIM10 and TIM11)
There are six synchronizable general-purpose timers embedded in the STM32L100C6 and
STM32L100R8/RB devices (see Table 5 for differences).

TIM2, TIM3, TIM4


These timers are based on a 16-bit auto-reload up/down-counter and a 16-bit prescaler.
They feature 4 independent channels each for input capture/output compare, PWM or one-
pulse mode output. This gives up to 12 input captures/output compares/PWMs on the
largest packages.
The TIM2, TIM3, TIM4 general-purpose timers can work together or with the TIM10, TIM11
and TIM9 general-purpose timers via the Timer Link feature for synchronization or event
chaining. Their counter can be frozen in debug mode. Any of the general-purpose timers
can be used to generate PWM outputs.
TIM2, TIM3, TIM4 all have independent DMA request generation.
These timers are capable of handling quadrature (incremental) encoder signals and the
digital outputs from 1 to 3 hall-effect sensors.

TIM10, TIM11 and TIM9


TIM10 and TIM11 are based on a 16-bit auto-reload upcounter. TIM9 is based on a 16-bit
auto-reload up/down counter. They include a 16-bit prescaler. TIM10 and TIM11 feature one
independent channel, whereas TIM9 has two independent channels for input capture/output
compare, PWM or one-pulse mode output. They can be synchronized with the TIM2, TIM3,
TIM4 full-featured general-purpose timers.
They can also be used as simple time bases and be clocked by the LSE clock source
(32.768 kHz) to provide time bases independent from the main CPU clock.

3.14.2 Basic timers (TIM6 and TIM7)


These timers are mainly used for DAC trigger generation. They can also be used as generic
16-bit time bases.

3.14.3 SysTick timer


This timer is dedicated to the OS, but could also be used as a standard downcounter. It is
based on a 24-bit down-counter with autoreload capability and a programmable clock
source. It features a maskable system interrupt generation when the counter reaches 0.

3.14.4 Independent watchdog (IWDG)


The independent watchdog is based on a 12-bit down-counter and 8-bit prescaler. It is
clocked from an independent 37 kHz internal RC and, as it operates independently of the
main clock, it can operate in Stop and Standby modes. It can be used either as a watchdog
to reset the device when a problem occurs, or as a free-running timer for application timeout
management. It is hardware- or software-configurable through the option bytes. The counter
can be frozen in debug mode.

26/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Functional overview

3.14.5 Window watchdog (WWDG)


The window watchdog is based on a 7-bit down-counter that can be set as free-running. It
can be used as a watchdog to reset the device when a problem occurs. It is clocked from
the main clock. It has an early warning interrupt capability and the counter can be frozen in
debug mode.

3.15 Communication interfaces

3.15.1 I²C bus


Up to two I²C bus interfaces can operate in multimaster and slave modes. They can support
standard and fast modes.
They support dual slave addressing (7-bit only) and both 7- and 10-bit addressing in master
mode. A hardware CRC generation/verification is embedded.
They can be served by DMA and they support SM Bus 2.0/PM Bus.

3.15.2 Universal synchronous/asynchronous receiver transmitter (USART)


All USART interfaces are able to communicate at speeds of up to 4 Mbit/s. They provide
hardware management of the CTS and RTS signals and are ISO 7816 compliant. They
support IrDA SIR ENDEC and have LIN Master/Slave capability.
All USART interfaces can be served by the DMA controller.

3.15.3 Serial peripheral interface (SPI)


Up to two SPIs are able to communicate at up to 16 Mbits/s in slave and master modes in
full-duplex and half-duplex communication modes. The 3-bit prescaler gives 8 master mode
frequencies and the frame is configurable to 8 bits or 16 bits. The hardware CRC
generation/verification supports basic SD Card/MMC modes.
Both SPIs can be served by the DMA controller.

3.15.4 Universal serial bus (USB)


The STM32L100C6 and STM32L100R8/RB devices embed a USB device peripheral
compatible with the USB full speed 12 Mbit/s. The USB interface implements a full speed
(12 Mbit/s) function interface. It has software-configurable endpoint setting and supports
suspend/resume. The dedicated 48 MHz clock is generated from the internal main PLL (the
clock source must use a HSE crystal oscillator).

DocID024295 Rev 6 27/103


39
Functional overview STM32L100C6 STM32L100R8/RB

3.16 CRC (cyclic redundancy check) calculation unit


The CRC (cyclic redundancy check) calculation unit is used to get a CRC code from a 32-bit
data word and a fixed generator polynomial.
Among other applications, CRC-based techniques are used to verify data transmission or
storage integrity. In the scope of the EN/IEC 60335-1 standard, they offer a means of
verifying the Flash memory integrity. The CRC calculation unit helps compute a signature of
the software during runtime, to be compared with a reference signature generated at link-
time and stored at a given memory location.

3.17 Development support


Serial wire JTAG debug port (SWJ-DP)
The ARM SWJ-DP interface is embedded, and is a combined JTAG and serial wire debug
port that enables either a serial wire debug or a JTAG probe to be connected to the target.
The JTAG JTMS and JTCK pins are shared with SWDAT and SWCLK, respectively, and a
specific sequence on the JTMS pin is used to switch between JTAG-DP and SW-DP.
The JTAG port can be permanently disabled with a JTAG fuse.

28/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Pin descriptions

4 Pin descriptions

Figure 3. STM32L100C6 and STM32L100R8/RB LQFP64 pinout

%227
9''B
966B

3'
3&

3&
3&

3$
3$
3%
3%

3%
3%
3%
3%
3%
                       
9/&'   9''B
3&:.83   966B
3&26&B,1   3$
3&26&B287   3$
3+26&B,1   3$
3+26&B287   3$
1567   3$
3&   3$
3&  /4)3  3&
3&   3&
3&    3&
966$    3&
9''$   3%
3$:.83   3%
3$   3%
3$   3%
                       
966B
9''B

3&
3&
3%
3%
3%
3%

966B
9''B
3$

3$
3$
3$
3$

3%

DLG

1. This figure shows the package top view.

DocID024295 Rev 6 29/103


39
Pin descriptions STM32L100C6 STM32L100R8/RB

Figure 4. STM32L100C6 and STM32L100R8/RB UFQFPN48 pinout

"//4
6$$?

633?

0"

0"

0!

0!
0"

0"

0"

0"

0"
           
6,#$   6$$?

0# 7+50   633?

0# /3#?).   0!

0# /3#?/54   0!

0( /3#?).   0!

0( /3#?/54   0!


5&1&0.
.234   0!

633!   0!

6$$!   0"

0! 7+50   0"

0!   0"

0!   0"
           

6$$?
0"

0"

633?
0!

0!

0!

0!

0!

0"

0"

0"

AID

1. This figure shows the package top view.

30/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Pin descriptions

Table 6. Legend/abbreviations used in the pinout table


Name Abbreviation Definition

Unless otherwise specified in brackets below the pin name, the pin function
Pin name
during and after reset is the same as the actual pin name
S Supply pin
Pin type I Input only pin
I/O Input / output pin
FT 5 V tolerant I/O
TC Standard 3.3 V I/O
I/O structure
B Dedicated BOOT0 pin
RST Bidirectional reset pin with embedded weak pull-up resistor
Unless otherwise specified by a note, all I/Os are set as floating inputs during
Notes
and after reset
Alternate
Functions selected through GPIOx_AFR registers
functions
Pin
functions Additional
Functions directly selected/enabled through peripheral registers
functions

DocID024295 Rev 6 31/103


39
Pin descriptions STM32L100C6 STM32L100R8/RB

Table 7. STM32L100C6 and STM32L100R8/RB pin definitions


Pins Pin functions

I/O structure
Pin type(1)
Main
UFQFPN48

function(2)
LQFP64

Pin name Alternate functions Additional


(after reset)
functions

1 1 VLCD S - VLCD - -
RTC_TAMP1/
2 2 PC13-WKUP2 I/O FT PC13 - RTC_TS/
RTC_OUT/WKUP2
PC14-
3 3 I/O TC PC14 - OSC32_IN
OSC32_IN(3)
PC15-
4 4 OSC32_OUT I/O TC PC15 - OSC32_OUT
(4)

5 5 PH0-OSC_IN(4) I/O TC PH0 - OSC_IN


PH1-
6 6 I/O TC PH1 - OSC_OUT
OSC_OUT
7 7 NRST I/O RST NRST - -
ADC_IN10/
8 - PC0 I/O FT PC0 LCD_SEG18
COMP1_INP
ADC_IN11/
9 - PC1 I/O FT PC1 LCD_SEG19
COMP1_INP
ADC_IN12/
10 - PC2 I/O FT PC2 LCD_SEG20
COMP1_INP
ADC_IN13/
11 - PC3 I/O TC PC3 LCD_SEG21
COMP1_INP
12 8 VSSA S - VSSA - -
13 9 VDDA S - VDDA - -
WKUP1/ADC_IN0/
14 10 PA0-WKUP1 I/O FT PA0 USART2_CTS/TIM2_CH1_ETR
COMP1_INP
USART2_RTS/TIM2_CH2/ ADC_IN1/
15 11 PA1 I/O FT PA1
LCD_SEG0 COMP1_INP
USART2_TX/TIM2_CH3/TIM9_CH1 ADC_IN2/
16 12 PA2 I/O FT PA2
/LCD_SEG1 COMP1_INP
USART2_RX/TIM2_CH4/ ADC_IN3/
17 13 PA3 I/O TC PA3
TIM9_CH2/LCD_SEG2 COMP1_INP
18 - VSS_4 S - VSS_4 - -
19 - VDD_4 S - VDD_4 - -

32/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Pin descriptions

Table 7. STM32L100C6 and STM32L100R8/RB pin definitions (continued)


Pins Pin functions

I/O structure
Pin type(1)
Main
UFQFPN48

function(2)
LQFP64

Pin name Alternate functions Additional


(after reset)
functions

ADC_IN4/
20 14 PA4 I/O TC PA4 SPI1_NSS/USART2_CK DAC_OUT1/
COMP1_INP
ADC_IN5/
21 15 PA5 I/O TC PA5 SPI1_SCK/TIM2_CH1_ETR DAC_OUT2/
COMP1_INP
SPI1_MISO/TIM3_CH1/ ADC_IN6/
22 16 PA6 I/O FT PA6
LCD_SEG3/TIM10_CH1 COMP1_INP
SPI1_MOSI/TIM3_CH2/ ADC_IN7/
23 17 PA7 I/O FT PA7
LCD_SEG4/TIM11_CH1 COMP1_INP
ADC_IN14/
24 - PC4 I/O FT PC4 LCD_SEG22
COMP1_INP
ADC_IN15/
25 - PC5 I/O FT PC5 LCD_SEG23
COMP1_INP
ADC_IN8/
26 18 PB0 I/O TC PB0 TIM3_CH3/LCD_SEG5 COMP1_INP/
VREF_OUT
ADC_IN9/
27 19 PB1 I/O FT PB1 TIM3_CH4/LCD_SEG6 COMP1_INP/
VREF_OUT
28 20 PB2 I/O FT PB2/BOOT1 BOOT1 -
I2C2_SCL/USART3_TX/TIM2_CH3/
29 21 PB10 I/O FT PB10 -
LCD_SEG10
I2C2_SDA/USART3_RX/
30 22 PB11 I/O FT PB11 -
TIM2_CH4/LCD_SEG11
31 23 VSS_1 S - VSS_1 - -
32 24 VDD_1 S - VDD_1 - -
SPI2_NSS/I2C2_SMBA/
ADC_IN18/
33 25 PB12 I/O FT PB12 USART3_CK/LCD_SEG12/
COMP1_INP
TIM10_CH1
SPI2_SCK/USART3_CTS/ ADC_IN19/
34 26 PB13 I/O FT PB13
LCD_SEG13/TIM9_CH1 COMP1_INP
SPI2_MISO/USART3_RTS/ ADC_IN20/
35 27 PB14 I/O FT PB14
LCD_SEG14/TIM9_CH2 COMP1_INP

DocID024295 Rev 6 33/103


39
Pin descriptions STM32L100C6 STM32L100R8/RB

Table 7. STM32L100C6 and STM32L100R8/RB pin definitions (continued)


Pins Pin functions

I/O structure
Pin type(1)
Main
UFQFPN48

function(2)
LQFP64

Pin name Alternate functions Additional


(after reset)
functions

ADC_IN21/
SPI2_MOSI/LCD_SEG15/
36 28 PB15 I/O FT PB15 COMP1_INP/
TIM11_CH1
RTC_REFIN
37 - PC6 I/O FT PC6 TIM3_CH1/LCD_SEG24 -
38 - PC7 I/O FT PC7 TIM3_CH2/LCD_SEG25 -
39 - PC8 I/O FT PC8 TIM3_CH3/LCD_SEG26 -
40 - PC9 I/O FT PC9 TIM3_CH4/LCD_SEG27 -
41 29 PA8 I/O FT PA8 USART1_CK/MCO/LCD_COM0 -
42 30 PA9 I/O FT PA9 USART1_TX/LCD_COM1 -
43 31 PA10 I/O FT PA10 USART1_RX/LCD_COM2 -
44 32 PA11 I/O FT PA11 USART1_CTS/SPI1_MISO USB_DM
45 33 PA12 I/O FT PA12 USART1_RTS/SPI1_MOSI USB_DP
46 34 PA13 I/O FT JTMS-SWDIO JTMS-SWDIO -
47 35 VSS_2 S - VSS_2 - -
48 36 VDD_2 S - VDD_2 - -
49 37 PA14 I/O FT JTCK-SWCLK JTCK-SWCLK -
TIM2_CH1_ETR/PA15/
50 38 PA15 I/O FT JTDI -
SPI1_NSS/LCD_SEG17
USART3_TX/LCD_SEG28/
51 - PC10 I/O FT PC10 -
LCD_SEG40/LCD_COM4
USART3_RX/LCD_SEG29/
52 - PC11 I/O FT PC11 -
LCD_SEG41/LCD_COM5
USART3_CK/LCD_SEG30/
53 - PC12 I/O FT PC12 -
LCD_SEG42/LCD_COM6
TIM3_ETR/LCD_SEG30/
54 - PD2 I/O FT PD2 -
LCD_SEG43/LCD_COM7
TIM2_CH2/PB3/SPI1_SCK/
55 39 PB3 I/O FT JTDO COMP2_INM
LCD_SEG7/JTDO
TIM3_CH1/PB4/
56 40 PB4 I/O FT NJTRST COMP2_INP
SPI1_MISO/LCD_SEG8/NJTRST
I2C1_SMBA/TIM3_CH2/
57 41 PB5 I/O FT PB5 COMP2_INP
SPI1_MOSI/LCD_SEG9

34/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Pin descriptions

Table 7. STM32L100C6 and STM32L100R8/RB pin definitions (continued)


Pins Pin functions

I/O structure
Pin type(1)
Main
UFQFPN48

function(2)
LQFP64

Pin name Alternate functions Additional


(after reset)
functions

58 42 PB6 I/O FT PB6 I2C1_SCL/TIM4_CH1/USART1_TX -


I2C1_SDA/TIM4_CH2/
59 43 PB7 I/O FT PB7 PVD_IN
USART1_RX
60 44 BOOT0 I B BOOT0 - -
TIM4_CH3/I2C1_SCL/
61 45 PB8 I/O FT PB8 -
LCD_SEG16/TIM10_CH1
TIM4_CH4/I2C1_SDA/
62 46 PB9 I/O FT PB9 -
LCD_COM3/TIM11_CH1
63 47 VSS_3 S VSS_3 - -

64 48 VDD_3 S VDD_3 - -

1. I = input, O = output, S = supply.


2. Function availability depends on the chosen device. For devices having reduced peripheral counts, it is always the lower
number of peripheral that is included. For example, if a device has only one SPI and two USARTs, they will be called SPI1
and USART1 & USART2, respectively. Refer to Table 1 on page 10.
3. The PC14 and PC15 I/Os are only configured as OSC32_IN/OSC32_OUT when the LSE oscillator is on (by setting the
LSEON bit in the RCC_CSR register). The LSE oscillator pins OSC32_IN/OSC32_OUT can be used as general-purpose
PC14/PC15 I/Os, respectively, when the LSE oscillator is off ( after reset, the LSE oscillator is off ). The LSE has priority
over the GPIO function. For more details, refer to Using the OSC32_IN/OSC32_OUT pins as GPIO PC14/PC15 port pins
section in the STM32Lxx reference manual (RM0038).
4. The PH0 and PH1 I/Os are only configured as OSC_IN/OSC_OUT when the HSE oscillator is on ( by setting the HSEON
bit in the RCC_CR register). The HSE oscillator pins OSC_IN/OSC_OUT can be used as general-purpose PH0/PH1 I/Os,
respectively, when the HSE oscillator is off (after reset, the HSE oscillator is off ). The HSE has priority over the GPIO
function.

DocID024295 Rev 6 35/103


39
36/103

Pin descriptions
Table 8. Alternate function input/output
Digital alternate function number

AFI AFI AFIO AFIO


AFIO0 AFIO1 AFIO2 AFIO3 AFIO4 AFIO5 AFOI6 AFIO7 AFIO11 AFIO14 AFIO15
O8 O9 12 13
Port name
Alternate function

USART
SYSTEM TIM2 TIM3/4 TIM9/10/11 I2C1/2 SPI1/2 N/A N/A N/A LCD N/A N/A RI SYSTEM
1/2/3

BOOT0 BOOT0 - - - - - - - - - - - - - -

NRST NRST - - - - - - - - - - - - - -

PA0-WKUP1 - TIM2_CH1_ETR - - - - - USART2_CTS - - - - - TIMx_IC1 EVENTOUT

PA1 - TIM2_CH2 - - - - - USART2_RTS - - [SEG0] - - TIMx_IC2 EVENTOUT

PA2 - TIM2_CH3 - TIM9_CH1 - - - USART2_TX - - [SEG1] - - TIMx_IC3 EVENTOUT


DocID024295 Rev 6

PA3 - TIM2_CH4 - TIM9_CH2 - - - USART2_RX - - [SEG2] - - TIMx_IC4 EVENTOUT

PA4 - - - - - SPI1_NSS - USART2_CK - - - - - TIMx_IC1 EVENTOUT

PA5 - TIM2_CH1_ETR - - - SPI1_SCK - - - - - - - TIMx_IC2 EVENTOUT

PA6 - - TIM3_CH1 TIM10_CH1 - SPI1_MISO - - - - [SEG3] - - TIMx_IC3 EVENTOUT

PA7 - - TIM3_CH2 TIM11_CH1 - SPI1_MOSI - - - - [SEG4] - - TIMx_IC4 EVENTOUT

PA8 MCO - - - - - - USART1_CK - - [COM0] - - TIMx_IC1 EVENTOUT

PA9 - - - - - - - USART1_TX - - [COM1] - - TIMx_IC2 EVENTOUT

PA10 - - - - - - - USART1_RX - - [COM2] - - TIMx_IC3 EVENTOUT

STM32L100C6 STM32L100R8/RB
PA11 - - - - - SPI1_MISO - USART1_CTS - - - - - TIMx_IC4 EVENTOUT

PA12 - - - - - SPI1_MOSI - USART1_RTS - - - - - TIMx_IC1 EVENTOUT

JTMS-
PA13 - - - - - - - - - - - - TIMx_IC2 EVENTOUT
SWDIO

JTCK-
PA14 - - - - - - - - - - - - TIMx_IC3 EVENTOUT
SWCLK

PA15 JTDI TIM2_CH1_ETR - - - SPI1_NSS - - - - SEG17 - - TIMx_IC4 EVENTOUT

PB0 - - TIM3_CH3 - - - - - - - [SEG5] - - - EVENTOUT

PB1 - - TIM3_CH4 - - - - - - - [SEG6] - - - EVENTOUT

PB2 BOOT1 - - - - - - - - - - - - - EVENTOUT

PB3 JTDO TIM2_CH2 - - - SPI1_SCK - - - - [SEG7] - - - EVENTOUT


Table 8. Alternate function input/output (continued)

STM32L100C6 STM32L100R8/RB
Digital alternate function number

AFI AFI AFIO AFIO


AFIO0 AFIO1 AFIO2 AFIO3 AFIO4 AFIO5 AFOI6 AFIO7 AFIO11 AFIO14 AFIO15
O8 O9 12 13
Port name
Alternate function

USART
SYSTEM TIM2 TIM3/4 TIM9/10/11 I2C1/2 SPI1/2 N/A N/A N/A LCD N/A N/A RI SYSTEM
1/2/3

PB4 NJTRST - TIM3_CH1 - - SPI1_MISO - - - - [SEG8] - - - EVENTOUT

I2C1_
PB5 - - TIM3_CH2 - SPI1_MOSI - - - - [SEG9] - - - EVENTOUT
SMBA

PB6 - - TIM4_CH1 - I2C1_SCL - - USART1_TX - - - - - - EVENTOUT

PB7 - - TIM4_CH2 - I2C1_SDA - - USART1_RX - - - - - - EVENTOUT

PB8 - - TIM4_CH3 TIM10_CH1* I2C1_SCL - - - - - SEG16 - - - EVENTOUT

PB9 - - TIM4_CH4 TIM11_CH1* I2C1_SDA - - - - - [COM3] - - - EVENTOUT


DocID024295 Rev 6

PB10 - TIM2_CH3 - - I2C2_SCL - - USART3_TX - - SEG10 - - - EVENTOUT

PB11 - TIM2_CH4 - - I2C2_SDA - - USART3_RX - - SEG11 - - - EVENTOUT

I2C2_
PB12 - - - TIM10_CH1 SPI2_NSS - USART3_CK - - SEG12 - - - EVENTOUT
SMBA

PB13 - - - TIM9_CH1 - SPI2_SCK - USART3_CTS - - SEG13 - - - EVENTOUT

PB14 - - - TIM9_CH2 - SPI2_MISO - USART3_RTS - - SEG14 - - - EVENTOUT

PB15 - - - TIM11_CH1 - SPI2_MOSI - - - - SEG15 - - - EVENTOUT

PC0 - - - - - - - - - - SEG18 - - TIMx_IC1 EVENTOUT

PC1 - - - - - - - - - - SEG19 - - TIMx_IC2 EVENTOUT

PC2 - - - - - - - - - - SEG20 - - TIMx_IC3 EVENTOUT

PC3 - - - - - - - - - - SEG21 - - TIMx_IC4 EVENTOUT

PC4 - - - - - - - - - - SEG22 - - TIMx_IC1 EVENTOUT

PC5 - - - - - - - - - - SEG23 - - TIMx_IC2 EVENTOUT

Pin descriptions
PC6 - - TIM3_CH1 - - - - - - - SEG24 - - TIMx_IC3 EVENTOUT

PC7 - - TIM3_CH2 - - - - - - - SEG25 - - TIMx_IC4 EVENTOUT

PC8 - - TIM3_CH3 - - - - - - - SEG26 - - TIMx_IC1 EVENTOUT


37/103

PC9 - - TIM3_CH4 - - - - - - - SEG27 - - TIMx_IC2 EVENTOUT


Table 8. Alternate function input/output (continued)
38/103

Pin descriptions
Digital alternate function number

AFI AFI AFIO AFIO


AFIO0 AFIO1 AFIO2 AFIO3 AFIO4 AFIO5 AFOI6 AFIO7 AFIO11 AFIO14 AFIO15
O8 O9 12 13
Port name
Alternate function

USART
SYSTEM TIM2 TIM3/4 TIM9/10/11 I2C1/2 SPI1/2 N/A N/A N/A LCD N/A N/A RI SYSTEM
1/2/3

COM4 /
PC10 - - - - - - - USART3_TX - - SEG28 / - - TIMx_IC3 EVENTOUT
SEG40

COM5 /
PC11 - - - - - - - USART3_RX - - SEG29 / - - TIMx_IC4 EVENTOUT
SEG41

COM6 /
PC12 - - - - - - - USART3_CK - - SEG30 / - - TIMx_IC1 EVENTOUT
SEG42
DocID024295 Rev 6

PC13-
- - - - - - - - - - - - - TIMx_IC2 EVENTOUT
WKUP2

PC14-
- - - - - - - - - - - - - TIMx_IC3 EVENTOUT
OSC32_IN

PC15-
- - - - - - - - - - - - - TIMx_IC4 EVENTOUT
OSC32_OUT

COM7 /
PD2 - - TIM3_ETR - - - - - - - SEG31 / - - TIMx_IC3 EVENTOUT

STM32L100C6 STM32L100R8/RB
SEG43

PH0-
- - - - - - - - - - - - - - -
OSC_IN

PH1-
- - - - - - - - - - - - - - -
OSC_OUT
STM32L100C6 STM32L100R8/RB Memory mapping

5 Memory mapping

The memory map is shown in the following figure.

Figure 5. Memory map


$3%PHPRU\VSDFH
[))))))))
UHVHUYHG
[(
UHVHUYHG
[
UHVHUYHG
[
'0$
[
[)))))))) UHVHUYHG
[
)ODVK,QWHUI DFH
[&
5&&
 [
UHVHUYHG
[( [
#RUWH[ 0,QWHUQDO  &5&
3HULSKHUDOV [
[( UHVHUYHG
[
3RUW+
[
UHVHUYHG
[
 3RUW'
[&
3RUW&
[
[& [ 3RUW%
3RUW$
[
UHVHUYHG
[&
 [
86$57

UHVHUYHG
[
[$  63,
[
UHVHUYHG

[
$'&
[
 UHVH UYH G
[
7,0
[
[
7,0
[&
7,0
[
(;7,
 [))) [
2SWLRQ%\WHV 6<6&)*
[
[))
UHVHUYHG
[ RESE UYHG
&2035,
[)) [&
UHVHUYHG
RESE RVED [
 [
'$& 
6\VWHPPHPRU\
3:5
[
[ 3HULSKHUDOV [)) UHVHUYHG
[
E\WH
[ 86%
86%5HJ LVWHUV
[&
 ,&
[
,&
65$0 UHVH RVED [
[  UHVHUYHG
[&
86$57
[
86$57
 [
[ UHVHUYHG
'DWD((3520
[&
[ 63,
[
[ RESE UYHG UHVHUYHG
[
[ ,:'*
[
::'*
[&
)ODVKPHPRU\ 57&
[
/&'
5HVHUYHG [ [
$OLDVHGWR)ODVKRUV\VWHP UHVHUYHG
[&
PHPRU\GHSHQGLQJRQ 7,0
[
[ %227SLQV
7,0
[
UHVHUYHG
[&
7,0
[
7,0
[
7,0
[

069

DocID024295 Rev 6 39/103


39
Electrical characteristics STM32L100C6 STM32L100R8/RB

6 Electrical characteristics

6.1 Parameter conditions


Unless otherwise specified, all voltages are referenced to VSS.

6.1.1 Minimum and maximum values


Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100% of the devices with an ambient temperature at TA = 25 °C and TA = TAmax (given by
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes. Based on characterization, the minimum and maximum
values refer to sample tests and represent the mean value plus or minus three times the
standard deviation (mean±3σ).
Please refer to device ErrataSheet for possible latest changes of electrical characteristics.

6.1.2 Typical values


Unless otherwise specified, typical data are based on TA = 25 °C, VDD = 3.6 V (for the
1.8 V ≤ VDD ≤ 3.6 V voltage range). They are given only as design guidelines and are not
tested.
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean±2σ).

6.1.3 Typical curves


Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.

6.1.4 Loading capacitor


The loading conditions used for pin parameter measurement are shown in Figure 6.

6.1.5 Pin input voltage


The input voltage measurement on a pin of the device is described in Figure 7.

Figure 6. Pin loading conditions Figure 7. Pin input voltage

0&8SLQ 0&8SLQ
& S)
9,1

DLF DLG

40/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.1.6 Power supply scheme

Figure 8. Power supply scheme

6WDQGE\SRZHUFLUFXLWU\
26&.57&
:DNHXSORJLF
57&EDFNXSUHJLVWHUV

/HYHOVKLIWHU
287
,2 .HUQHO
*3,2V /RJLF ORJLF
,1 &38
'LJLWDO 
0HPRULHV 
9''

9''1
5HJXODWRU
1[Q)
[—)
9661

9''$
9''$

$QDORJ
95()
Q) $'& 5&V3//
—) 95() '$& &203

966$

069

DocID024295 Rev 6 41/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.1.7 Optional LCD power supply scheme

Figure 9. Optional LCD power supply scheme


VSEL
VDD

VDD1/2/.../N Step-up
N x 100 nF Converter
+ 1 x 10 μF

Option 1 VLCD

100 nF
VLCD LCD
Option 2
CEXT

VSS1/2/.../N

MS32462V1

1. Option 1: LCD power supply is provided by a dedicated VLCD supply source, VSEL switch is open.
2. Option 2: LCD power supply is provided by the internal step-up converter, VSEL switch is closed, an
external capacitance is needed for correct behavior of this converter.

6.1.8 Current consumption measurement

Figure 10. Current consumption measurement scheme

$ 1[9''
1[Q)
 [—)

1[966

9/&'
9''$
Q) 95()
—)
95()
966$

069

42/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.2 Absolute maximum ratings


Stresses above the absolute maximum ratings listed in Table 9: Voltage characteristics,
Table 10: Current characteristics, and Table 11: Thermal characteristics may cause
permanent damage to the device. These are stress ratings only and functional operation of
the device at these conditions is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.

Table 9. Voltage characteristics


Symbol Ratings Min Max Unit

External main supply voltage


VDD–VSS –0.3 4.0
(including VDDA and VDD)(1)
V
Input voltage on five-volt tolerant pin VSS −0.3 VDD+4.0
VIN(2)
Input voltage on any other pin VSS − 0.3 4.0
|ΔVDDx| Variations between different VDD power pins - 50
mV
|VSSX − VSS| Variations between all different ground pins(3) - 50
Electrostatic discharge voltage
VESD(HBM) see Section 6.3.11 -
(human body model)
1. All main power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external power
supply, in the permitted range.
2. VIN maximum must always be respected. Refer to Table 10 for maximum allowed injected current values.
3. Include VREF- pin.

Table 10. Current characteristics


Symbol Ratings Max. Unit

ΣIVDD Total current into VDD/VDDA power lines (source)(1) 80


ΣIVSS Total current out of VSSground lines (sink)(1) 80
Output current sunk by any I/O and control pin 25
IIO
Output current sourced by any I/O and control pin - 25 mA
Injected current on five-volt tolerant I/O(3) RST and B pins -5/+0
IINJ(PIN) (2)
Injected current on any other pin(4) ±5
(5)
ΣIINJ(PIN) Total injected current (sum of all I/O and control pins) ± 25
1. All main power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external power
supply, in the permitted range.
2. Negative injection disturbs the analog performance of the device. See note in Section 6.3.17.
3. Positive current injection is not possible on these I/Os. A negative injection is induced by VIN<VSS. IINJ(PIN)
must never be exceeded. Refer to Table 9 for maximum allowed input voltage values.
4. A positive injection is induced by VIN > VDD while a negative injection is induced by VIN < VSS. IINJ(PIN)
must never be exceeded. Refer to Table 9: Voltage characteristics for the maximum allowed input voltage
values.
5. When several inputs are submitted to a current injection, the maximum ΣIINJ(PIN) is the absolute sum of the
positive and negative injected currents (instantaneous values).

DocID024295 Rev 6 43/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 11. Thermal characteristics


Symbol Ratings Value Unit

TSTG Storage temperature range –65 to +150 °C


TJ Maximum junction temperature 105 °C

TLEAD Maximum lead temperature during soldering see note (1) °C


(LQFP64, UFQFPN48)
1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb assembly), the ST ECOPACK®
7191395 specification, and the European directive on Restrictions on Hazardous Substances (ROHS
directive 2011/65/EU, July 2011).

6.3 Operating conditions

6.3.1 General operating conditions

Table 12. General operating conditions


Symbol Parameter Conditions Min Max Unit

fHCLK Internal AHB clock frequency - 0 32


fPCLK1 Internal APB1 clock frequency - 0 32 MHz
fPCLK2 Internal APB2 clock frequency - 0 32
BOR detector enabled,
1.8 3.6
(at power-on)
VDD Standard operating voltage V
BOR detector disabled, after
1.65 3.6
power on
Must be the same voltage as
VDDA(1) Analog operating voltage 1.8 3.6 V
VDD(2)
FT pins: 2.0 V ≤VDD –0.3 5.5(3)
FT pins: VDD < 2.0 V –0.3 5.25(3)
VIN I/O input voltage V
BOOT0 0 5.5
Any other pin –0.3 VDD+0.3
LQFP64 package - 444
PD Power dissipation at TA = 85 °C(4) mW
UFQFPN48 package - 606
TA Ambient temperature range Maximum power dissipation –40 85
TJ Junction temperature range -40 °C ≤ TA ≤ 85°C -40 105 °C
1. When the ADC is used, refer to Table 53: ADC characteristics.
2. It is recommended to power VDD and VDDA from the same source. A maximum difference of 300 mV between VDD and
VDDA can be tolerated during power-up and operation.
3. To sustain a voltage higher than VDD+0.3 V, the internal pull-up/pull-down resistors must be disabled.
4. If TA is lower, higher PD values are allowed as long as TJ does not exceed TJ max (see Section 7.3: Thermal characteristics
on page 97).

44/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.3.2 Embedded reset and power control block characteristics


The parameters given in the following table are derived from the tests performed under the
ambient temperature condition summarized in the following table.

Table 13. Embedded reset and power control block characteristics


Symbol Parameter Conditions Min Typ Max Unit

VDD rise time rate BOR detector enabled 0 - ∞


tVDD(1) BOR detector enabled 20 - ∞ µs/V
VDD fall time rate
BOR detector disabled 0 - 1000
(1)
TRSTTEMPO Reset temporization VDD rising, BOR enabled - 2 3.3 ms

Power on/power down reset Falling edge 1 1.5 1.65


VPOR/PDR V
threshold Rising edge 1.3 1.5 1.65
Falling edge 1.67 1.7 1.74
VBOR0 Brown-out reset threshold 0
Rising edge 1.69 1.76 1.8
Falling edge 1.87 1.93 1.97
VBOR1 Brown-out reset threshold 1
Rising edge 1.96 2.03 2.07
Falling edge 2.22 2.30 2.35
VBOR2 Brown-out reset threshold 2 V
Rising edge 2.31 2.41 2.44
Falling edge 2.45 2.55 2.60
VBOR3 Brown-out reset threshold 3
Rising edge 2.54 2.66 2.7
Falling edge 2.68 2.8 2.85
VBOR4 Brown-out reset threshold 4
Rising edge 2.78 2.9 2.95

Programmable voltage detector Falling edge 1.8 1.85 1.88


VPVD0
threshold 0 Rising edge 1.88 1.94 1.99
Falling edge 1.98 2.04 2.09
VPVD1 PVD threshold 1
Rising edge 2.08 2.14 2.18
Falling edge 2.20 2.24 2.28
VPVD2 PVD threshold 2
Rising edge 2.28 2.34 2.38
Falling edge 2.39 2.44 2.48
VPVD3 PVD threshold 3 V
Rising edge 2.47 2.54 2.58
Falling edge 2.57 2.64 2.69
VPVD4 PVD threshold 4
Rising edge 2.68 2.74 2.79
Falling edge 2.77 2.83 2.88
VPVD5 PVD threshold 5
Rising edge 2.87 2.94 2.99
Falling edge 2.97 3.05 3.09
VPVD6 PVD threshold 6
Rising edge 3.08 3.15 3.20

DocID024295 Rev 6 45/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 13. Embedded reset and power control block characteristics (continued)
Symbol Parameter Conditions Min Typ Max Unit

BOR0 threshold - 40 -
Vhyst Hysteresis voltage All BOR and PVD thresholds mV
- 100 -
excepting BOR0
1. Guaranteed by characterization results.

46/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.3.3 Embedded internal reference voltage


The parameters given in the following table are based on characterization results, unless
otherwise specified.

Table 14. Embedded internal reference voltage calibration values


Calibration value name Description Memory address

Raw data acquired at


VREFINT_CAL temperature of 30 °C ±5 °C, 0x1FF8 0078-0x1FF8 0079
VDDA= 3 V ±10 mV

Table 15. Embedded internal reference voltage


Symbol Parameter Conditions Min Typ Max Unit

VREFINT out(1) Internal reference voltage – 40 °C < TJ < +85 °C 1.202 1.224 1.242 V
Internal reference current
IREFINT - - 1.4 2.3 µA
consumption
TVREFINT Internal reference startup time - - 2 3 ms
VDDA voltage during VREFINT factory
VVREF_MEAS - 2.99 3 3.01 V
measure
Including uncertainties
Accuracy of factory-measured VREF
AVREF_MEAS due to ADC and VDDA - - ±5 mV
value (2)
values
TCoeff(3) Temperature coefficient –40 °C < TJ < +105 °C - 25 100 ppm/°C
ACoeff (3) Long-term stability 1000 hours, T= 25 °C - - 1000 ppm
(3)(4)
VDDCoeff Voltage coefficient 3.0 V < VDDA < 3.6 V - - 2000 ppm/V
ADC sampling time when reading the
TS_vrefint(3) - 4 - - µs
internal reference voltage
Startup time of reference voltage
TADC_BUF(3) - - - 10 µs
buffer for ADC
Consumption of reference voltage
IBUF_ADC(3) - - 13.5 25 µA
buffer for ADC
IVREF_OUT(3) VREF_OUT output current(5) - - - 1 µA
CVREF_OUT(3) VREF_OUT output load - - - 50 pF
Consumption of reference voltage
ILPBUF(3) - - 730 1200 nA
buffer for VREF_OUT and COMP
VREFINT_DIV1(3) 1/4 reference voltage - 24 25 26
(3)
VREFINT_DIV2 1/2 reference voltage - 49 50 51 % VREFINT
(3)
VREFINT_DIV3 3/4 reference voltage - 74 75 76
1. Guaranteed by test in production.
2. The internal VREF value is individually measured in production and stored in dedicated EEPROM bytes.
3. Guaranteed by characterization results.
4. Shortest sampling time can be determined in the application by multiple interactions.
5. To guarantee less than 1% VREF_OUT deviation.

DocID024295 Rev 6 47/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.4 Supply current characteristics


The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code. The current consumption is measured as described in Figure 10: Current
consumption measurement scheme.
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code, unless otherwise
specified.
The current consumption values are derived from the tests performed under ambient
temperature TA=25°C and VDD supply voltage conditions summarized in Table 12: General
operating conditions, unless otherwise specified.

Maximum current consumption


The MCU is placed under the following conditions:
• VDD = 3.6 V
• All I/O pins are in input mode with a static value at VDD or VSS (no load).
• All peripherals are disabled except when explicitly mentioned.
• The Flash memory access time is adjusted depending on fHCLK frequency and voltage
range.
• Prefetch and 64-bit access are enabled in configurations with 1 wait state.
• When the peripherals are enabled fAPB1 = fAPB2 = fAHB.
• When fHCLK > 8 MHz, PLL is ON and PLL inputs are equal to HSI = 8 MHz (if internal
clock is used) or HSE = 8 MHz (if HSE bypass mode is used).

48/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 16. Current consumption in Run mode, code with data processing running from Flash
Max(1)
Symbol Parameter Conditions fHCLK Typ Unit
55 °C 85 °C

1 MHz 270 400 400


Range 3, VCORE=1.2
2 MHz 470 600 600 µA
V VOS[1:0] = 11
4 MHz 890 1025 1025
fHSE = fHCLK
up to 16 MHz, 4 MHz 1 1.3 1.3
included Range 2, VCORE=1.5
8 MHz 2 2.5 2.5
fHSE = fHCLK/2 above V VOS[1:0] = 10
16 MHz 16 MHz 3.9 5 5
Supply (PLL ON)(2)
current in 8 MHz 2.16 3 3
IDD (Run Run mode, Range 1, VCORE=1.8
16 MHz 4.8 5.5 5.5
V VOS[1:0] = 01
from Flash) code
executed 32 MHz 9.6 11 11
from Flash mA
Range 2, VCORE=1.5
16 MHz 4 5 5
HSI clock source (16 V VOS[1:0] = 10
MHz) Range 1, VCORE=1.8
32 MHz 9.4 11 11
V VOS[1:0] = 01
MSI clock, 65 kHz 65 kHz 0.05 0.085 0.09
Range 3, VCORE=1.2
MSI clock, 524 kHz 524 kHz 0.15 0.185 0.19
V VOS[1:0] = 11
MSI clock, 4.2 MHz 4.2 MHz 0.9 1 1
1. Guaranteed by characterization results, unless otherwise specified.
2. Oscillator bypassed (HSEBYP = 1 in RCC_CR register).

DocID024295 Rev 6 49/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 17. Current consumption in Run mode, code with data processing running from RAM
Max(1)
Symbol Parameter Conditions fHCLK Typ Unit
105 °C

1 MHz 200 300


Range 3,
VCORE=1.2 V 2 MHz 380 500 µA
VOS[1:0] = 11
4 MHz 720 860
fHSE = fHCLK
up to 16 MHz, 4 MHz 0.9 1
Range 2,
included
VCORE=1.5 V 8 MHz 1.65 2
fHSE = fHCLK/2 above
VOS[1:0] = 10
16 MHz 16 MHz 3.2 3.7
(PLL ON)(2)
8 MHz 2 2.5
Supply current in Range 1,
Run mode, code VCORE=1.8 V 16 MHz 4 4.5
IDD (Run VOS[1:0] = 01
executed from 32 MHz 7.7 8.5 mA
from RAM) RAM, Flash
switched off Range 2,
VCORE=1.5 V 16 MHz 3.3 3.8
HSI clock source VOS[1:0] = 10
(16 MHz) Range 1,
VCORE=1.8 V 32 MHz 7.8 9.2
VOS[1:0] = 01
MSI clock, 65 kHz 65 kHz 40 80
Range 3,
MSI clock, 524 kHz VCORE=1.2 V 524 kHz 110 160 µA
VOS[1:0] = 11
MSI clock, 4.2 MHz 4.2 MHz 700 820
1. Guaranteed by characterization results, unless otherwise specified.
2. Oscillator bypassed (HSEBYP = 1 in RCC_CR register).

50/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 18. Current consumption in Sleep mode


Max(1)
Symbol Parameter Conditions fHCLK Typ Unit
55 °C 85 °C

1 MHz 80 140 140


Range 3, VCORE=1.2
2 MHz 150 210 210
V VOS[1:0] = 11
4 MHz 280 330 330
fHSE = fHCLK up to 4 MHz 280 400 400
16 MHz included, Range 2, VCORE=1.5
8 MHz 450 550 550
fHSE = fHCLK/2 above V VOS[1:0] = 10
16 MHz (PLL ON)(2) 16 MHz 900 1050 1050
Supply 8 MHz 550 650 650
current in Range 1, VCORE=1.8
Sleep 16 MHz 1050 1200 1200 µA
V VOS[1:0] = 01
mode, Flash 32 MHz 2300 2500 2500
OFF
Range 2, VCORE=1.5
16 MHz 1000 1100 1100
HSI clock source V VOS[1:0] = 10
(16 MHz) Range 1, VCORE=1.8
32 MHz 2300 2500 2500
V VOS[1:0] = 01
MSI clock, 65 kHz 65 kHz 30 50 50
IDD Range 3, VCORE=1.2
MSI clock, 524 kHz 524 kHz 50 70 70
(Sleep) V VOS[1:0] = 11
MSI clock, 4.2 MHz 4.2 MHz 200 240 240
1 MHz 80 140 140
Range 3, VCORE=1.2
2 MHz 150 210 210
V VOS[1:0] = 11
4 MHz 290 350 350
fHSE = fHCLK up to 4 MHz 300 400 400
16 MHz included, Range 2, VCORE=1.5
8 MHz 500 600 600
Supply fHSE = fHCLK/2 above V VOS[1:0] = 10
current in 16 MHz (PLL ON)(2) 16 MHz 1000 1100 1100
Sleep µA
8 MHz 550 650 650
mode, Flash
Range 1, VCORE=1.8
ON 16 MHz 1050 1200 1200
V VOS[1:0] = 01
32 MHz 2300 2500 2500
Range 2, VCORE=1.5
16 MHz 1000 1100 1100
HSI clock source (16 V VOS[1:0] = 10
MHz) Range 1, VCORE=1.8
32 MHz 2300 2500 2500
V VOS[1:0] = 01
Supply MSI clock, 65 kHz 65 kHz 40 70 70
current in
IDD MSI clock, 524 kHz Range 3, VCORE=1.2V 524 kHz 60 90 90
Sleep µA
(Sleep) VOS[1:0] = 11
mode, Flash
MSI clock, 4.2 MHz 4.2 MHz 210 250 250
ON
1. Guaranteed by characterization results, unless otherwise specified.
2. Oscillator bypassed (HSEBYP = 1 in RCC_CR register)

DocID024295 Rev 6 51/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 19. Current consumption in Low power run mode


Max
Symbol Parameter Conditions Typ (1) Unit

All MSI clock, 65 kHz TA = -40 °C to 25 °C 9 12


peripherals fHCLK = 32 kHz TA = 85 °C 17.5 24
OFF, code
executed MSI clock, 65 kHz TA = -40 °C to 25 °C 14 17
from RAM, fHCLK = 65 kHz TA = 85 °C 22 29
Flash
switched TA = -40 °C to 25 °C 37 42
OFF, VDD MSI clock, 131 kHz
from 1.8 V TA = 55 °C 37 42
Supply fHCLK = 131 kHz
IDD (LP current in to 3.6 V TA = 85 °C 37 42
Run) Low power TA = -40 °C to 25 °C 24 32
MSI clock, 65 kHz
run mode All fHCLK = 32 kHz TA = 85 °C 33 42 µA
peripherals
OFF, code MSI clock, 65 kHz TA = -40 °C to 25 °C 31 40
executed fHCLK = 65 kHz TA = 85 °C 40 48
from Flash,
VDD from TA = -40 °C to 25 °C 48 58
1.8 V to MSI clock, 131 kHz
TA = 55 °C 54 63
3.6 V fHCLK = 131 kHz
TA = 85 °C 56 65
Max allowed
IDD Max VDD from
current in
(LP 1.8 V to - - - 200
Low power
Run)(2) 3.6 V
run mode
1. Guaranteed by characterization results, unless otherwise specified.
2. This limitation is related to the consumption of the CPU core and the peripherals that are powered by the regulator.
Consumption of the I/Os is not included in this limitation.

52/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 20. Current consumption in Low power sleep mode


Max
Symbol Parameter Conditions Typ (1) Unit

MSI clock, 65 kHz


fHCLK = 32 kHz TA = -40 °C to 25 °C 4.4 -
Flash OFF
MSI clock, 65 kHz TA = -40 °C to 25 °C 17.5 25
All fHCLK = 32 kHz
TA = 85 °C 22 27
peripherals Flash ON
OFF, VDD
MSI clock, 65 kHz TA = -40 °C to 25 °C 18 26
from 1.8 V
to 3.6 V fHCLK = 65 kHz,
Flash ON TA = 85 °C 23 28
Supply
current in T = -40 °C to 25 °C 22 30
IDD (LP MSI clock, 131 kHz A
Low power TA = 55 °C 24 32
Sleep) fHCLK = 131 kHz,
sleep
Flash ON
mode TA = 85 °C 26 34

MSI clock, 65 kHz TA = -40 °C to 25 °C 17.5 25 µA

TIM9 and fHCLK = 32 kHz TA = 85 °C 22 27


USART1
MSI clock, 65 kHz TA = -40 °C to 25 °C 18 26
enabled,
Flash ON, fHCLK = 65 kHz TA = 85 °C 23 28
VDD from
TA = -40 °C to 25 °C 22 30
1.8 V to
MSI clock, 131 kHz
3.6 V TA = 55 °C 24 32
fHCLK = 131 kHz
TA = 85 °C 26 34
Max
allowed
VDD from
IDD Max current in
1.8 V to - - - 200
(LP Sleep) Low power
3.6 V
Sleep
mode
1. Guaranteed by characterization results, unless otherwise specified.

DocID024295 Rev 6 53/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 21. Typical and maximum current consumptions in Stop mode


Typ Max
Symbol Parameter Conditions (1) (1)(2) Unit

TA = -40°C to 25°C
1.2 2.75
VDD = 1.8 V
LCD TA = -40°C to 25°C 1.4 4
OFF
TA = 55°C 2.6 6
RTC clocked by LSI, TA= 85°C 4.8 10
regulator in LP mode,
HSI and HSE OFF T = -40°C to 25°C 3.3 6
LCD ON A
(no independent (static TA = 55°C 4.5 8
watchdog) duty)(3)
TA= 85°C 6.6 12
T = -40°C to 25°C 7.7 10
LCD ON A
(1/8 TA = 55°C 8.6 12
duty)(4)
TA= 85°C 10.7 16

Supply current TA = -40°C to 25°C 1.6 4


IDD (Stop in Stop mode LCD
TA = 55°C 2.7 6 µA
with RTC OFF
with RTC)
enabled TA= 85°C 4.8 10
RTC clocked by LSE
external clock (32.768 TA = -40°C to 25°C 3.6 6
LCD ON
kHz), regulator in LP
(static TA = 55°C 4.6 8
mode, HSI and HSE
duty)(3)
OFF (no independent TA= 85°C 6.7 12
watchdog)
TA = -40°C to 25°C 7.6 10
LCD ON
(1/8 TA = 55°C 8.6 12
duty)(4)
TA= 85°C 10.7 16
TA = -40°C to 25°C
1.45 -
VDD = 1.8 V
RTC clocked by LSE
LCD TA = -40°C to 25°C
(no independent 1.9 -
OFF VDD = 3.0 V
watchdog)(5)
TA = -40°C to 25°C
2.2 -
VDD = 3.6 V
Regulator in LP mode, HSI and
HSE OFF, independent TA = -40°C to 25°C 1.1 2.2
Supply current watchdog and LSI enabled
IDD (Stop) in Stop mode TA = -40°C to 25°C 0.5 0.9 µA
(RTCdisabled) Regulator in LP mode, LSI, HSI
and HSE OFF (no independent TA = 55°C 1.9 5
watchdog)
TA= 85°C 3.7 8

54/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 21. Typical and maximum current consumptions in Stop mode (continued)
Typ Max
Symbol Parameter Conditions (1) (1)(2) Unit

RMS (root MSI = 4.2 MHz 2 -


mean square)
MSI = 1.05 MHz 1.45 -
supply current
IDD (WU VDD = 3.0 V
during wakeup mA
from Stop) time when TA = -40°C to 25°C
MSI = 65 kHz(6) 1.45 -
exiting from
Stop mode
1. The typical values are given for VDD = 3.0 V and max values are given for VDD = 3.6 V, unless otherwise
specified.
2. Guaranteed by characterization results, unless otherwise specified.
3. LCD enabled with external VLCD, static duty, division ratio = 256, all pixels active, no LCD connected.
4. LCD enabled with external VLCD, 1/8 duty, 1/3 bias, division ratio = 64, all pixels active, no LCD
connected.
5. Based on characterization done with a 32.768 kHz crystal (MC306-G-06Q-32.768, manufacturer JFVNY)
with two 6.8pF loading capacitors.
6. When MSI = 64 kHz, the RMS current is measured over the first 15 µs following the wakeup event. For the
remaining time of the wakeup period, the current is similar to the Run mode current.

Table 22. Typical and maximum current consumptions in Standby mode


Max
Symbol Parameter Conditions Typ(1) (1)(2) Unit

TA = -40 °C to 25 °C
0.9 -
VDD = 1.8 V
RTC clocked by LSI (no TA = -40 °C to 25 °C 1.1 1.8
independent watchdog)
TA = 55 °C 1.42 2.5
IDD TA= 85 °C 1.87 3
Supply current in Standby
(Standby mode with RTC enabled TA = -40 °C to 25 °C
with RTC) 1 -
VDD = 1.8 V
RTC clocked by LSE (no TA = -40 °C to 25 °C 1.33 2.9 µA
independent watchdog)(3)
TA = 55 °C 1.59 3.4
TA= 85 °C 2.01 4.3
Independent watchdog
TA = -40 °C to 25 °C 1.1 1.6
and LSI enabled
IDD Supply current in Standby TA = -40 °C to 25 °C 0.3 0.55
(Standby) mode with RTC disabled Independent watchdog
TA = 55 °C 0.5 0.8
and LSI OFF
TA = 85 °C 1 1.7
IDD (WU RMS supply current during
VDD = 3.0 V
from wakeup time when exiting - 1 - mA
TA = -40 °C to 25 °C
Standby) from Standby mode
1. The typical values are given for VDD = 3.0 V and max values are given for VDD = 3.6 V, unless otherwise specified.
2. Guaranteed by characterization results, unless otherwise specified.
3. Based on characterization done with a 32.768 kHz crystal (MC306-G-06Q-32.768, manufacturer JFVNY) with two 6.8pF
loading capacitors.

DocID024295 Rev 6 55/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

On-chip peripheral current consumption


The current consumption of the on-chip peripherals is given in the following table. The MCU
is placed under the following conditions:
• all I/O pins are in input mode with a static value at VDD or VSS (no load)
• all peripherals are disabled unless otherwise mentioned
• the given value is calculated by measuring the current consumption
– with all peripherals clocked off
– with only one peripheral clocked on

Table 23. Peripheral current consumption(1)


Typical consumption, VDD = 3.0 V, TA = 25 °C

Peripheral Range 1, Range 2, Range 3, Unit


Low power
VCORE=1.8 V VCORE=1.5 V VCORE=1.2 V
sleep and run
VOS[1:0] = 01 VOS[1:0] = 10 VOS[1:0] = 11

TIM2 13 10.5 8 10.5


TIM3 14 12 9 12
TIM4 12.5 10.5 8 11
TIM6 5.5 4.5 3.5 4.5
TIM7 5.5 5 3.5 4.5
LCD 5.5 5 3.5 5
WWDG 4 3.5 2.5 3.5
SPI2 5.5 5 4 5 µA/MHz
APB1
USART2 9 8 5.5 8.5 (fHCLK)

USART3 10.5 9 6 8
I2C1 8.5 7 5.5 7.5
I2C2 8.5 7 5.5 6.5
USB 12.5 10 6.5 10
PWR 4.5 4 3 3.5
DAC 9 7.5 6 7
COMP 4.5 4 3.5 4.5
SYSCFG & RI 3 2.5 2 2.5
TIM9 9 7.5 6 7
TIM10 6.5 5.5 4.5 5.5
µA/MHz
APB2 TIM11 7 6 4.5 5.5
(fHCLK)
ADC(2) 11.5 9.5 8 9
SPI1 5 4.5 3 4
USART1 9 7.5 6 7.5

56/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 23. Peripheral current consumption(1) (continued)


Typical consumption, VDD = 3.0 V, TA = 25 °C

Peripheral Range 1, Range 2, Range 3, Unit


Low power
VCORE=1.8 V VCORE=1.5 V VCORE=1.2 V
sleep and run
VOS[1:0] = 01 VOS[1:0] = 10 VOS[1:0] = 11

GPIOA 5 4.5 3.5 4


GPIOB 5 4.5 3.5 4.5
GPIOC 5 4.5 3.5 4.5
GPIOD 5 4.5 3.5 4.5
AHB GPIOH 4 4 3 3.5 µA/MHz
CRC 1 0.5 0.5 0.5 (fHCLK)

FLASH 13 11.5 9 18.5


DMA1 12 10 8 10.5
All enabled 166 138 106 130
IDD (RTC) 0.47
IDD (LCD) 3.1
IDD (ADC)(3) 1450
(4)
IDD (DAC) 340
IDD (COMP1) 0.16 µA
Slow mode 2
IDD (COMP2)
Fast mode 5
IDD (PVD / BOR)(5) 2.6
IDD (IWDG) 0.25
1. Data based on differential IDD measurement between all peripherals OFF an one peripheral with clock enabled, in the
following conditions: fHCLK = 32 MHz (Range 1), fHCLK = 16 MHz (Range 2), fHCLK = 4 MHz (Range 3), fHCLK = 64kHz
(Low power run/sleep), fAPB1 = fHCLK, fAPB2 = fHCLK, default prescaler value for each peripheral. The CPU is in Sleep
mode in both cases. No I/O pins toggling.
2. HSI oscillator is OFF for this measure.
3. Data based on a differential IDD measurement between ADC in reset configuration and continuous ADC conversion (HSI
consumption not included).
4. Data based on a differential IDD measurement between DAC in reset configuration and continuous DAC conversion of
VDD/2. DAC is in buffered mode, output is left floating.
5. Including supply current of internal reference voltage.

6.3.5 Wakeup time from Low-power mode


The wakeup times given in the following table are measured with the MSI RC oscillator. The
clock source used to wake up the device depends on the current operating mode:
• Sleep mode: the clock source is the clock that was set before entering Sleep mode
• Stop mode: the clock source is the MSI oscillator in the range configured before
entering Stop mode
• Standby mode: the clock source is the MSI oscillator running at 2.1 MHz

DocID024295 Rev 6 57/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

All timings are derived from tests performed under ambient temperature and VDD supply
voltage conditions summarized in Table 12.

Table 24. Low-power mode wakeup timings


Symbol Parameter Conditions Typ Max(1) Unit

tWUSLEEP Wakeup from Sleep mode fHCLK = 32 MHz 0.36 -


fHCLK = 262 kHz
Wakeup from Low-power sleep 32 -
Flash enabled
tWUSLEEP_LP mode
fHCLK = 262 kHz fHCLK = 262 kHz
34 -
Flash switched OFF
Wakeup from Stop mode,
fHCLK = fMSI = 4.2 MHz 8.2 -
regulator in Run mode
fHCLK = fMSI = 4.2 MHz
8.2 9.3
Voltage Ranges 1 and 2
fHCLK = fMSI = 4.2 MHz
7.8 11.2 µs
Voltage Range 3
tWUSTOP fHCLK = fMSI = 2.1 MHz 10 12
Wakeup from Stop mode,
regulator in low-power mode fHCLK = fMSI = 1.05 MHz 15.5 20
fHCLK = fMSI = 524 kHz 29 35
fHCLK = fMSI = 262 kHz 53 63
fHCLK = fMSI = 131 kHz 105 118
fHCLK = MSI = 65 kHz 210 237
Wakeup from Standby mode
fHCLK = MSI = 2.1 MHz 50 103
FWU bit = 1
tWUSTDBY
Wakeup from Standby mode
fHCLK = MSI = 2.1 MHz 2.5 3.2 ms
FWU bit = 0
1. Guaranteed by characterization results, unless otherwise specified

58/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.3.6 External clock source characteristics


High-speed external user clock generated from an external source
In bypass mode the HSE oscillator is switched off and the input pin is a standard GPIO. The
external clock signal has to respect the I/O characteristics in Section 6.3.13. However, the
recommended clock input waveform is shown in Figure 11.

Table 25. High-speed external user clock characteristics(1)


Symbol Parameter Conditions Min Typ Max Unit

CSS is on or
1
User external clock source PLL is used
fHSE_ext 8 32 MHz
frequency CSS is off, PLL
0
not used
VHSEH OSC_IN input pin high level voltage 0.7VDD - VDD
VHSEL OSC_IN input pin low level voltage VSS 0.3VDD
tw(HSEH) -
OSC_IN high or low time 12 - -
tw(HSEL)
ns
tr(HSE)
OSC_IN rise or fall time - - 20
tf(HSE)
Cin(HSE) OSC_IN input capacitance - - 2.6 - pF
1. Guaranteed by design.

Figure 11. High-speed external clock source AC timing diagram

WZ +6(+

9+6(+


9+6(/

WU +6( W
WI +6( WZ +6(/
7+6(

069

DocID024295 Rev 6 59/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Low-speed external user clock generated from an external source


The characteristics given in the following table result from tests performed using a low-
speed external clock source, and under ambient temperature and supply voltage conditions
summarized in Table 12.

Table 26. Low-speed external user clock characteristics(1)


Symbol Parameter Min Typ Max Unit

fLSE_ext User external clock source frequency 1 32.768 1000 kHz


VLSEH OSC32_IN input pin high level voltage 0.7VDD - VDD -
VLSEL OSC32_IN input pin low level voltage VSS - 0.3VDD -
tw(LSEH)
OSC32_IN high or low time 465 - -
tw(LSEL)
ns
tr(LSE)
OSC32_IN rise or fall time - - 10
tf(LSE)
CIN(LSE) OSC32_IN input capacitance - 0.6 - pF
1. Guaranteed by design.

Figure 12. Low-speed external clock source AC timing diagram

WZ /6(+

9/6(+


9/6(/

WU /6( W
WI /6( WZ /6(/
7/6(

069

High-speed external clock generated from a crystal/ceramic resonator


The high-speed external (HSE) clock can be supplied with a 1 to 24 MHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on
characterization results obtained with typical external components specified in Table 27. In
the application, the resonator and the load capacitors have to be placed as close as
possible to the oscillator pins in order to minimize output distortion and startup stabilization
time. Refer to the crystal resonator manufacturer for more details on the resonator
characteristics (frequency, package, accuracy).

Table 27. HSE oscillator characteristics(1)(2)


Symbol Parameter Conditions Min Typ Max Unit

fOSC_IN Oscillator frequency - 1 24 MHz


RF Feedback resistor - 200 - kΩ

60/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 27. HSE oscillator characteristics(1)(2) (continued)


Symbol Parameter Conditions Min Typ Max Unit

Recommended load
capacitance versus
C RS = 30 Ω - 20 - pF
equivalent serial resistance
of the crystal (RS)(3)
VDD= 3.3 V, VIN = VSS
IHSE HSE driving current - - 3 mA
with 30 pF load
C = 20 pF 2.5 (startup)
- -
HSE oscillator power fOSC = 16 MHz 0.7 (stabilized)
IDD(HSE) mA
consumption C = 10 pF 2.5 (startup)
- -
fOSC = 16 MHz 0.46 (stabilized)
mA
gm Oscillator transconductance Startup 3.5 - -
/V
tSU(HSE)
(4) Startup time VDD is stabilized - 1 - ms

1. Resonator characteristics given by the crystal/ceramic resonator manufacturer.


2. Guaranteed by characterization results.
3. The relatively low value of the RF resistor offers a good protection against issues resulting from use in a
humid environment, due to the induced leakage and the bias condition change. However, it is
recommended to take this point into account if the MCU is used in tough humidity conditions.
4. tSU(HSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz
oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly
with the crystal manufacturer.

For CL1 and CL2, it is recommended to use high-quality external ceramic capacitors in the
5 pF to 25 pF range (typ.), designed for high-frequency applications, and selected to match
the requirements of the crystal or resonator (see Figure 13). CL1 and CL2 are usually the
same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of CL1 and CL2. PCB and MCU pin capacitance must be included (10 pF
can be used as a rough estimate of the combined pin and board capacitance) when sizing
CL1 and CL2. Refer to the application note AN2867 “Oscillator design guide for ST
microcontrollers” available from the ST website www.st.com.

DocID024295 Rev 6 61/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Figure 13. HSE oscillator circuit diagram

I+6(WRFRUH
5P

&2 5)
/P
&/
&P 26&B,1
JP
5HVRQDWRU
&RQVXPSWLRQ
FRQWURO
5HVRQDWRU

670
26&B287
&/

DLE

Low-speed external clock generated from a crystal/ceramic resonator


The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on
characterization results obtained with typical external components specified in Table 12. In
the application, the resonator and the load capacitors have to be placed as close as
possible to the oscillator pins in order to minimize output distortion and startup stabilization
time. Refer to the crystal resonator manufacturer for more details on the resonator
characteristics (frequency, package, accuracy).

Table 28. LSE oscillator characteristics (fLSE = 32.768 kHz)(1)


Symbol Parameter Conditions Min Typ Max Unit

Low speed external oscillator


fLSE - - 32.768 - kHz
frequency
RF Feedback resistor - - 1.2 - MΩ
Recommended load capacitance
C(2) versus equivalent serial RS = 30 kΩ - 8 - pF
resistance of the crystal (RS)(3)
ILSE LSE driving current VDD = 3.3 V, VIN = VSS - - 1.1 µA
VDD = 1.8 V - 450 -
LSE oscillator current
IDD (LSE) VDD = 3.0 V - 600 - nA
consumption
VDD = 3.6V - 750 -
gm Oscillator transconductance - 3 - - µA/V
(4)
tSU(LSE) Startup time VDD is stabilized - 1 - s
1. Guaranteed by characterization results.
2. Refer to the note and caution paragraphs below the table, and to the application note AN2867 “Oscillator
design guide for ST microcontrollers”.
3. The oscillator selection can be optimized in terms of supply current using an high quality resonator with
small RS value for example MSIV-TIN32.768kHz. Refer to crystal manufacturer for more details.
4. tSU(LSE) is the startup time measured from the moment it is enabled (by software) to a stabilized
32.768 kHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary
significantly with the crystal manufacturer.

62/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Note: For CL1 and CL2, it is recommended to use high-quality ceramic capacitors in the 5 pF to
15 pF range selected to match the requirements of the crystal or resonator (see Figure 14 ).
CL1 and CL2, are usually the same size. The crystal manufacturer typically specifies a load
capacitance which is the series combination of CL1 and CL2.
Load capacitance CL has the following formula: CL = CL1 x CL2 / (CL1 + CL2) + Cstray
where Cstray is the pin capacitance and board or trace PCB-related capacitance. Typically,
it is between 2 pF and 7 pF.
Caution: To avoid exceeding the maximum value of CL1 and CL2 (15 pF) it is strongly recommended
to use a resonator with a load capacitance CL ≤ 7 pF. Never use a resonator with a load
capacitance of 12.5 pF.
Example: if the user chooses a resonator with a load capacitance of CL = 6 pF and
Cstray = 2 pF, then CL1 = CL2 = 8 pF.

Figure 14. Typical application with a 32.768 kHz crystal

5HVRQDWRUZLWK
LQWHJUDWHGFDSDFLWRUV
&/
26&B,1 I/6(
%LDV
N+]
5) FRQWUROOHG
UHVRQDWRU
JDLQ
26&B287 670/[[
&/
DLE

DocID024295 Rev 6 63/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.7 Internal clock source characteristics


The parameters given in the following table are derived from tests performed under ambient
temperature and VDD supply voltage conditions summarized in Table 12.

High-speed internal (HSI) RC oscillator

Table 29. HSI oscillator characteristics


Symbol Parameter Conditions Min Typ Max Unit

fHSI Frequency VDD = 3.0 V - 16 - MHz

HSI user-trimmed Trimming code is not a multiple of 16 - ± 0.4 0.7 %


(1)(2)
TRIM resolution Trimming code is a multiple of 16 - - ± 1.5 %
VDDA = 1.8 V to 3.6 V
ACCHSI(2) - -10 - +10 %
TA = -40 to 85 °C
HSI oscillator
tSU(HSI)(2) - - 3.7 6 µs
startup time
HSI oscillator
IDD(HSI)(2) - - 100 140 µA
power consumption
1. The trimming step differs depending on the trimming code. It is usually negative on the codes which are
multiples of 16 (0x00, 0x10, 0x20, 0x30...0xE0).
2. Guaranteed by characterization results.

Low-speed internal (LSI) RC oscillator

Table 30. LSI oscillator characteristics


Symbol Parameter Min Typ Max Unit

fLSI(1) LSI frequency 26 38 56 kHz


LSI oscillator frequency drift
DLSI(2) -10 - 4 %
0°C ≤TA ≤ 85°C
tsu(LSI)(3) LSI oscillator startup time - - 200 µs
IDD(LSI) (3) LSI oscillator power consumption - 400 510 nA
1. Guaranteed by test in production.
2. This is a deviation for an individual part, once the initial frequency has been measured.
3. Guaranteed by design.

64/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Multi-speed internal (MSI) RC oscillator

Table 31. MSI oscillator characteristics


Symbol Parameter Condition Typ Max Unit

MSI range 0 65.5 -


MSI range 1 131 -
kHz
MSI range 2 262 -
Frequency after factory calibration, done at
fMSI MSI range 3 524 -
VDD= 3.3 V and TA = 25 °C
MSI range 4 1.05 -
MSI range 5 2.1 - MHz
MSI range 6 4.2 -
ACCMSI Frequency error after factory calibration - ±0.5 - %
MSI oscillator frequency drift
DTEMP(MSI)(1) - ±10 - %
0 °C ≤TA ≤85 °C
MSI oscillator frequency drift
DVOLT(MSI)(1) - - 2.5 %/V
1.8 V ≤VDD ≤3.6 V, TA = 25 °C
MSI range 0 0.75 -
MSI range 1 1 -
MSI range 2 1.5 -
IDD(MSI)(2) MSI oscillator power consumption MSI range 3 2.5 - µA
MSI range 4 4.5 -
MSI range 5 8 -
MSI range 6 15 -
MSI range 0 30 -
MSI range 1 20 -
MSI range 2 15 -
MSI range 3 10 -
MSI range 4 6 -
tSU(MSI) MSI oscillator startup time µs
MSI range 5 5 -
MSI range 6,
Voltage range 1 3.5 -
and 2
MSI range 6,
5 -
Voltage range 3

DocID024295 Rev 6 65/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 31. MSI oscillator characteristics (continued)


Symbol Parameter Condition Typ Max Unit

MSI range 0 - 40
MSI range 1 - 20
MSI range 2 - 10
MSI range 3 - 4
MSI range 4 - 2.5
tSTAB(MSI)(2) MSI oscillator stabilization time µs
MSI range 5 - 2
MSI range 6,
Voltage range 1 - 2
and 2
MSI range 3,
- 3
Voltage Range 3
Any range to
- 4
range 5
fOVER(MSI) MSI oscillator frequency overshoot MHz
Any range to
- 6
range 6
1. This is a deviation for an individual part, once the initial frequency has been measured.
2. Guaranteed by characterization results.

6.3.8 PLL characteristics


The parameters given in Table 32 are derived from tests performed under ambient
temperature and VDD supply voltage conditions summarized in Table 12.

Table 32. PLL characteristics


Value
Symbol Parameter Unit
Min Typ Max(1)

PLL input clock(2) 2 - 24 MHz


fPLL_IN
PLL input clock duty cycle 45 - 55 %
fPLL_OUT PLL output clock 2 - 32 MHz
PLL lock time
tLOCK PLL input = 16 MHz - 115 160 µs
PLL VCO = 96 MHz
Jitter Cycle-to-cycle jitter - - ± 600 ps
IDDA(PLL) Current consumption on VDDA - 220 450
µA
IDD(PLL) Current consumption on VDD - 120 150
1. Guaranteed by characterization results.
2. Take care of using the appropriate multiplier factors so as to have PLL input clock values compatible with
the range defined by fPLL_OUT.

66/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.3.9 Memory characteristics


The characteristics are given at TA = -40 to 85 °C unless otherwise specified.

RAM memory

Table 33. RAM and hardware registers


Symbol Parameter Conditions Min Typ Max Unit

VRM Data retention mode(1) STOP mode (or RESET) 1.8 - - V


1. Minimum supply voltage without losing data stored in RAM (in Stop mode or under Reset) or in hardware
registers (only in Stop mode).

Flash memory and data EEPROM

Table 34. Flash memory and data EEPROM characteristics


Symbol Parameter Conditions Min Typ Max(1) Unit

Operating voltage
VDD - 1.8 - 3.6 V
Read / Write / Erase
Programming / erasing time for Erasing - 3.28 3.94
tprog byte / word / double word / half- ms
page Programming - 3.28 3.94

Average current during whole


- 300 - µA
program/erase operation
IDD TA = 25 °C, VDD = 3.6 V
Maximum current (peak) during
- 1.5 2.5 mA
program/erase operation
1. Guaranteed by design.

Table 35. Flash memory, data EEPROM endurance and data retention
Value
Symbol Parameter Conditions Unit
Min(1) Typ Max

Cycling (erase / write)


1 - -
Program memory TA = -40°C to
NCYC (2) kcycles
Cycling (erase / write) 85 °C
100 - -
EEPROM data memory
Data retention (program memory) after
10 - -
1 kcycle at TA = 85 °C
tRET(2) TRET = +85 °C years
Data retention (EEPROM data memory)
10 - -
after 100 kcycles at TA = 85 °C
1. Guaranteed by characterization results.
2. Characterization is done according to JEDEC JESD22-A117.

DocID024295 Rev 6 67/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.10 EMC characteristics


Susceptibility tests are performed on a sample basis during the device characterization.

Functional EMS (electromagnetic susceptibility)


While a simple application is executed on the device (toggling 2 LEDs through I/O ports).
the device is stressed by two electromagnetic events until a failure occurs. The failure is
indicated by the LEDs:
• Electrostatic discharge (ESD) (positive and negative) is applied to all device pins until
a functional disturbance occurs. This test is compliant with the IEC 61000-4-2 standard.
• FTB: A Burst of Fast Transient voltage (positive and negative) is applied to VDD and
VSS through a 100 pF capacitor, until a functional disturbance occurs. This test is
compliant with the IEC 61000-4-4 standard.
A device reset allows normal operations to be resumed.
The test results are given in Table 36. They are based on the EMS levels and classes
defined in application note AN1709.

Table 36. EMS characteristics


Level/
Symbol Parameter Conditions
Class

VDD = 3.3 V, LQFP100, TA = +25 °C,


Voltage limits to be applied on any I/O pin
VFESD fHCLK = 32 MHz 2B
to induce a functional disturbance
conforms to IEC 61000-4-2
Fast transient voltage burst limits to be VDD = 3.3 V, LQFP100, TA = +25 °C,
VEFTB applied through 100 pF on VDD and VSS fHCLK = 32 MHz 4A
pins to induce a functional disturbance conforms to IEC 61000-4-4

Designing hardened software to avoid noise problems


EMC characterization and optimization are performed at component level with a typical
application environment and simplified MCU software. It should be noted that good EMC
performance is highly dependent on the user application and the software in particular.
Therefore it is recommended that the user applies EMC software optimization and
prequalification tests in relation with the EMC level requested for his application.
Software recommendations
The software flowchart must include the management of runaway conditions such as:
• Corrupted program counter
• Unexpected reset
• Critical data corruption (control registers...)
Prequalification trials
Most of the common failures (unexpected reset and program counter corruption) can be
reproduced by manually forcing a low state on the NRST pin or the oscillator pins for 1
second.

68/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

To complete these trials, ESD stress can be applied directly on the device, over the range of
specification values. When unexpected behavior is detected, the software can be hardened
to prevent unrecoverable errors occurring (see application note AN1015).

Electromagnetic Interference (EMI)


The electromagnetic field emitted by the device are monitored while a simple application is
executed (toggling 2 LEDs through the I/O ports). This emission test is compliant with
IEC 61967-2 standard which specifies the test board and the pin loading.

Table 37. EMI characteristics


Max vs. frequency range
Monitored 4 MHz 16 MHz
Symbol Parameter Conditions 32 MHz Unit
frequency band
voltage voltage voltage
Range 3 Range 2 Range 1

VDD = 3.3 V, 0.1 to 30 MHz 3 -6 -5


TA = 25 °C, 30 to 130 MHz 18 4 -7 dBµV
SEMI Peak level LQFP100 package
compliant with IEC 130 MHz to 1GHz 15 5 -7
61967-2 SAE EMI Level 2.5 2 1 -

6.3.11 Electrical sensitivity characteristics


Based on three different tests (ESD, LU) using specific measurement methods, the device is
stressed in order to determine its performance in terms of electrical sensitivity.

Electrostatic discharge (ESD)


Electrostatic discharges (a positive then a negative pulse separated by 1 second) are
applied to the pins of each sample according to each pin combination. The sample size
depends on the number of supply pins in the device (3 parts × (n+1) supply pins). This test
conforms to the JESD22-A114/C101 standard.

Table 38. ESD absolute maximum ratings


Maximum
Symbol Ratings Conditions Packages Class Unit
value(1)

Electrostatic discharge voltage TA = +25 °C, conforming to


VESD(HBM) All 2 2000 V
(human body model) JESD22-A114
Electrostatic discharge voltage TA = +25 °C, conforming to
VESD(CDM) All III 500 V
(charge device model) JESD22-C101
1. Guaranteed by characterization results.

DocID024295 Rev 6 69/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Static latch-up
Two complementary static tests are required on six parts to assess the latch-up
performance:
• A supply overvoltage is applied to each power supply pin
• A current injection is applied to each input, output and configurable I/O pin
These tests are compliant with EIA/JESD 78A IC latch-up standard.

Table 39. Electrical sensitivities


Symbol Parameter Conditions Class

LU Static latch-up class TA = +85 °C conforming to JESD78A II level A

6.3.12 I/O current injection characteristics


As a general rule, current injection to the I/O pins, due to external voltage below VSS or
above VDD (for standard pins) should be avoided during normal product operation.
However, in order to give an indication of the robustness of the microcontroller in cases
when abnormal injection accidentally happens, susceptibility tests are performed on a
sample basis during device characterization.

Functional susceptibility to I/O current injection


While a simple application is executed on the device, the device is stressed by injecting
current into the I/O pins programmed in floating input mode. While current is injected into
the I/O pin, one at a time, the device is checked for functional failures.
The failure is indicated by an out of range parameter: ADC error above a certain limit (higher
than 5 LSB TUE), out of conventional limits of induced leakage current on adjacent pins (out
of –5 µA/+0 µA range), or other functional failure (for example reset occurrence, oscillator
frequency deviation, LCD levels).
The test results are given in Table 40.

Table 40. I/O current injection susceptibility


Functional susceptibility
Symbol Description Unit
Negative Positive
injection injection

Injected current on all 5 V tolerant (FT) pins -5 NA(1)


IINJ Injected current on BOOT0 -0 NA(1) mA
Injected current on any other pin -5 +5
1. Injection is not possible.

Note: It is recommended to add a Schottky diode (pin to ground) to analog pins which may
potentially inject negative currents.

70/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

6.3.13 I/O port characteristics


General input/output characteristics
Unless otherwise specified, the parameters given in Table 41 are derived from tests
performed under conditions summarized in Table 12. All I/Os are CMOS and TTL compliant.

Table 41. I/O static characteristics


Symbol Parameter Conditions Min Typ Max Unit

TC and FT I/O - - 0.3 VDD(1)(2)


VIL Input low level voltage
BOOT0 - 0.14 VDD(2)
TC I/O 0.45 VDD+0.38(2) - -
VIH Input high level voltage FT I/O 0.39 VDD+0.59(2) - - V
BOOT0 0.15 VDD+0.56(2) - -

I/O Schmitt trigger voltage TC and FT I/O - 10% VDD(3) -


Vhys
hysteresis(2) BOOT0 - 0.01 -
VSS ≤VIN ≤VDD
- - ±50
I/Os with LCD
VSS ≤VIN ≤VDD
I/Os with analog - - ±50
switches
VSS ≤VIN ≤VDD
nA
I/Os with analog - - ±50
Ilkg Input leakage current(4) switches and LCD
VSS ≤VIN ≤VDD
- - ±250
I/Os with USB
VSS ≤VIN ≤VDD
- - ±50
TC and FT I/O
FT I/O
- - ±10 uA
VDD ≤VIN ≤5V
Weak pull-up equivalent
RPU VIN = VSS 30 45 60 kΩ
resistor(5)(1)
Weak pull-down equivalent
RPD VIN = VDD 30 45 60 kΩ
resistor(5)
CIO I/O pin capacitance - - 5 - pF
1. Guaranteed by test in production.
2. Guaranteed by design.
3. With a minimum of 200 mV.
4. The max. value may be exceeded if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
PMOS/NMOS contribution to the series resistance is minimal (~10% order).

DocID024295 Rev 6 71/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Output driving current


The GPIOs (general purpose input/outputs) can sink or source up to ±8 mA, and sink or
source up to ±20 mA (with the non-standard VOL/VOH specifications given in Table 42.
In the user application, the number of I/O pins which can drive current must be limited to
respect the absolute maximum rating specified in Section 6.2:
• The sum of the currents sourced by all the I/Os on VDD, plus the maximum Run
consumption of the MCU sourced on VDD, cannot exceed the absolute maximum rating
ΣIVDD (see Table 10).
• The sum of the currents sunk by all the I/Os on VSS plus the maximum Run
consumption of the MCU sunk on VSS cannot exceed the absolute maximum rating
ΣIVSS (see Table 10).

Output voltage levels


Unless otherwise specified, the parameters given in Table 42 are derived from tests
performed under ambient temperature and VDD supply voltage conditions summarized in
Table 12. All I/Os are CMOS and TTL compliant.

Table 42. Output voltage characteristics


Symbol Parameter Conditions Min Max Unit

VOL(1)(2) Output low level voltage for an I/O pin IIO = 8 mA - 0.4
VOH(3)(2) Output high level voltage for an I/O pin 2.7 V < VDD < 3.6 V VDD-0.4 -
VOL (1)(4) Output low level voltage for an I/O pin - 0.45
IIO = 4 mA
V
VOH (3)(4) Output high level voltage for an I/O pin 1.8 V < VDD < 2.7 V VDD-0.45 -
VOL(1)(4) Output low level voltage for an I/O pin IIO = 20 mA - 1.3
VOH(3)(4) Output high level voltage for an I/O pin 2.7 V < VDD < 3.6 V VDD-1.3 -
1. The IIO current sunk by the device must always respect the absolute maximum rating specified in Table 10 and the sum of
IIO (I/O ports and control pins) must not exceed IVSS.
2. Guaranteed by test in production.
3. The IIO current sourced by the device must always respect the absolute maximum rating specified in Table 10 and the sum
of IIO (I/O ports and control pins) must not exceed IVDD.
4. Guaranteed by characterization results.

72/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Input/output AC characteristics
The definition and values of input/output AC characteristics are given in Figure 15 and
Table 43, respectively.
Unless otherwise specified, the parameters given in Table 43 are derived from tests
performed under ambient temperature and VDD supply voltage conditions summarized in
Table 12.

Table 43. I/O AC characteristics(1)


OSPEEDRx
[1:0] bit Symbol Parameter Conditions Min Max(2) Unit
value(1)

CL = 50 pF, VDD = 2.7 V to 3.6 V - 400


fmax(IO)out Maximum frequency(3) kHz
CL = 50 pF, VDD = 1.8 V to 2.7 V - 400
00
tf(IO)out CL = 50 pF, VDD = 2.7 V to 3.6 V - 625
Output rise and fall time ns
tr(IO)out CL = 50 pF, VDD = 1.8 V to 2.7 V - 625
CL = 50 pF, VDD = 2.7 V to 3.6 V - 2
fmax(IO)out Maximum frequency(3) MHz
CL = 50 pF, VDD = 1.8 V to 2.7 V - 1
01
tf(IO)out CL = 50 pF, VDD = 2.7 V to 3.6 V - 125
Output rise and fall time ns
tr(IO)out CL = 50 pF, VDD = 1.8 V to 2.7 V - 250
CL = 50 pF, VDD = 2.7 V to 3.6 V - 10
Fmax(IO)out Maximum frequency(3) MHz
CL = 50 pF, VDD = 1.8 V to 2.7 V - 2
10
tf(IO)out CL = 50 pF, VDD = 2.7 V to 3.6 V - 25
Output rise and fall time ns
tr(IO)out CL = 50 pF, VDD = 1.8 V to 2.7 V - 125
CL = 50 pF, VDD = 2.7 V to 3.6 V - 50
Fmax(IO)out Maximum frequency(3) MHz
CL = 50 pF, VDD = 1.8 V to 2.7 V - 8
11
tf(IO)out CL = 30 pF, VDD = 2.7 V to 3.6 V - 5
Output rise and fall time
tr(IO)out CL = 50 pF, VDD = 1.8 V to 2.7 V - 30
ns
Pulse width of external
- tEXTIpw signals detected by the - 8 -
EXTI controller
1. The I/O speed is configured using the OSPEEDRx[1:0] bits. Refer to the STM32L100C6 and STM32L100R8/RB reference
manual for a description of GPIO Port configuration register.
2. Guaranteed by design.
3. The maximum frequency is defined in Figure 15.

DocID024295 Rev 6 73/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Figure 15. I/O AC characteristics definition


 

 

 

%84%2.!, TR)/ OUT TF)/ OUT


/54054
/.P& 4

-AXIMUMFREQUENCYISACHIEVEDIFT R TF ” 4ANDIFTHEDUTYCYCLEIS 


WHENLOADEDBYP&

AIC

6.3.14 NRST pin characteristics


The NRST pin input driver uses CMOS technology. It is connected to a permanent pull-up
resistor, RPU (see Table 44).
Unless otherwise specified, the parameters given in Table 44 are derived from tests
performed under ambient temperature and VDD supply voltage conditions summarized in
Table 12.

Table 44. NRST pin characteristics


Symbol Parameter Conditions Min Typ Max Unit

VIL(NRST) (1)
NRST input low level voltage - - - 0.3 VDD
VIH(NRST)(1) NRST input high level voltage - 0.39 VDD+0.59 -
IOL = 2 mA
- - V
2.7 V < VDD < 3.6 V
VOL(NRST)(1) NRST output low level voltage 0.4
IOL = 1.5 mA
- -
1.8 V < VDD < 2.7 V
NRST Schmitt trigger voltage
Vhys(NRST)(1) - - 10%VDD(2) mV
hysteresis
Weak pull-up equivalent
RPU VIN = VSS 30 45 60 kΩ
resistor(3)
VF(NRST)(1) NRST input filtered pulse - - - 50 ns
VNF(NRST)(1) NRST input not filtered pulse - 350 - - ns
1. Guaranteed by design.
2. 200 mV minimum value.
3. The pull-up is designed with a true resistance in series with a switchable PMOS. This PMOS contribution to the series
resistance is around 10%.

74/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Figure 16. Recommended NRST pin protection

9''
([WHUQDOUHVHWFLUFXLW 

538 ,QWHUQDOUHVHW
1567 
)LOWHU
—)

670/[[

DLE

1. The reset network protects the device against parasitic resets. 0.1 uF capacitor must be placed as close as
possible to the chip.
2. The user must ensure that the level on the NRST pin can go below the VIL(NRST) max level specified in
Table 44. Otherwise the reset will not be taken into account by the device.

6.3.15 TIM timer characteristics


The parameters given in Table 45 are guaranteed by design.
Refer to Section 6.3.13: I/O port characteristics for details on the input/output alternate
function characteristics (output compare, input capture, external clock, PWM output).

Table 45. TIMx(1) characteristics


Symbol Parameter Conditions Min Max Unit

- 1 - tTIMxCLK
tres(TIM) Timer resolution time
fTIMxCLK = 32 MHz 31.25 - ns

Timer external clock - 0 fTIMxCLK/2 MHz


fEXT
frequency on CH1 to CH4 f
TIMxCLK = 32 MHz 0 16 MHz
ResTIM Timer resolution - - 16 bit
16-bit counter clock - 1 65536 tTIMxCLK
period when internal clock
tCOUNTER
is selected (timer’s fTIMxCLK = 32 MHz 0.0312 2048 µs
prescaler disabled)
- - 65536 × 65536 tTIMxCLK
tMAX_COUNT Maximum possible count
fTIMxCLK = 32 MHz - 134.2 s
1. TIMx is used as a general term to refer to the TIM2, TIM3 and TIM4 timers.

DocID024295 Rev 6 75/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.16 Communication interfaces


I2C interface characteristics
The STM32L100C6 and STM32L100R8/RB product line I2C interface meets the
requirements of the standard I2C communication protocol with the following restrictions:
SDA and SCL are not “true” open-drain I/O pins. When configured as open-drain, the PMOS
connected between the I/O pin and VDD is disabled, but is still present.
The I2C characteristics are described in Table 46. Refer also to Section 6.3.12: I/O current
injection characteristics for more details on the input/output alternate function characteristics
(SDA and SCL).

Table 46. I2C characteristics


Standard mode
Fast mode I2C(1)(2)
I2C(1)(2)
Symbol Parameter Unit
Min Max Min Max

tw(SCLL) SCL clock low time 4.7 - 1.3 -


µs
tw(SCLH) SCL clock high time 4.0 - 0.6 -
tsu(SDA) SDA setup time 250 - 100 -
th(SDA) SDA data hold time - 3450(3) - 900(3)
tr(SDA) ns
SDA and SCL rise time - 1000 - 300
tr(SCL)
tf(SDA)
SDA and SCL fall time - 300 - 300
tf(SCL)
th(STA) Start condition hold time 4.0 - 0.6 -
Repeated Start condition µs
tsu(STA) 4.7 - 0.6 -
setup time
tsu(STO) Stop condition setup time 4.0 - 0.6 - μs
Stop to Start condition time
tw(STO:STA) 4.7 - 1.3 - μs
(bus free)
Capacitive load for each bus
Cb - 400 - 400 pF
line
Pulse width of spikes that
tSP are suppressed by the 0 50(4) 0 50(4) ns
analog filter
1. Guaranteed by design.
2. fPCLK1 must be at least 2 MHz to achieve standard mode I²C frequencies. It must be at least 4 MHz to
achieve fast mode I²C frequencies. It must be a multiple of 10 MHz to reach the 400 kHz maximum I²C fast
mode clock.
3. The maximum Data hold time has only to be met if the interface does not stretch the low period of SCL
signal.
4. The minimum width of the spikes filtered by the analog filter is above tSP(max).

76/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Figure 17. I2C bus AC waveforms and measurement circuit

sͺ/Ϯ sͺ/Ϯ

ZW ZW ^dDϯϮ>ϭdždž
Z^
^
/ϮďƵƐ Z^
^>

^ dZdZWd

^ dZd

ƚƐƵ;^dͿ ^ dZd

^
ƚĨ;^Ϳ ƚƌ;^Ϳ ƚƐƵ;^Ϳ
^ dKW ƚƐƵ;^d͗^dKͿ
ƚŚ;^dͿ ƚǁ;^<>Ϳ ƚŚ;^Ϳ

^>
ƚǁ;^<,Ϳ ƚƌ;^<Ϳ ƚĨ;^<Ϳ ƚƐƵ;^dKͿ
ĂŝϭϳϴϱϱĐ

1. RS = series protection resistors


2. RP = pull-up resistors
3. VDD_I2C = I2C bus supply
4. Measurement points are done at CMOS levels: 0.3VDD and 0.7VDD.

Table 47. SCL frequency (fPCLK1= 32 MHz, VDD = VDD_I2C = 3.3 V)(1)(2)
I2C_CCR value
fSCL (kHz)
RP = 4.7 kΩ

400 0x801B
300 0x8024
200 0x8035
100 0x00A0
50 0x0140
20 0x0320
1. RP = External pull-up resistance, fSCL = I2C speed.
2. For speeds around 200 kHz, the tolerance on the achieved speed is of ±5%. For other speed ranges, the
tolerance on the achieved speed is ±2%. These variations depend on the accuracy of the external
components used to design the application.

DocID024295 Rev 6 77/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

SPI characteristics
Unless otherwise specified, the parameters given in the following table are derived from
tests performed under ambient temperature, fPCLKx frequency and VDD supply voltage
conditions summarized in Table 12.
Refer to Section 6.3.12: I/O current injection characteristics for more details on the
input/output alternate function characteristics (NSS, SCK, MOSI, MISO).

Table 48. SPI characteristics(1)


Symbol Parameter Conditions Min Max(2) Unit

Master mode - 16
fSCK
SPI clock frequency Slave mode - 16 MHz
1/tc(SCK)
Slave transmitter - 12(3)
tr(SCK)(2) SPI clock rise and fall
Capacitive load: C = 30 pF - 6 ns
tf(SCK)(2) time
SPI slave input clock duty
DuCy(SCK) Slave mode 30 70 %
cycle
tsu(NSS) NSS setup time Slave mode 4tHCLK -
th(NSS) NSS hold time Slave mode 2tHCLK -
(2)
tw(SCKH)
SCK high and low time Master mode tSCK/2− 5 tSCK/2+3
tw(SCKL)(2)
tsu(MI)(2) Master mode 5 -
Data input setup time
tsu(SI)(2) Slave mode 6 -
th(MI)(2) Master mode 5 - ns
Data input hold time
(2)
th(SI) Slave mode 5 -
(4)
ta(SO) Data output access time Slave mode 0 3tHCLK
(2)
tv(SO) Data output valid time Slave mode - 33
tv(MO)(2) Data output valid time Master mode - 6.5
th(SO) (2) Slave mode 17 -
Data output hold time
(2)
th(MO) Master mode 0.5 -
1. The characteristics above are given for voltage Range 1.
2. Guaranteed by characterization results.
3. The maximum SPI clock frequency in slave transmitter mode is given for an SPI slave input clock duty
cycle (DuCy(SCK)) ranging between 40 to 60%.
4. Min time is for the minimum time to drive the output and max time is for the maximum time to validate the
data.

78/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Figure 18. SPI timing diagram - slave mode and CPHA = 0

Figure 19. SPI timing diagram - slave mode and CPHA = 1(1)

166LQSXW

W68 166 WF 6&. WK 166


6&.LQSXW

&3+$ 
&32/  WZ 6&.+
&3+$  WZ 6&./
&32/ 

WU 6&.
WY 62 WK 62 WGLV 62
WD 62 WI 6&.
0,62
06%287 %,7287 /6%287
287387
WVX 6, WK 6,
026,
,1387 06%,1 %,7,1 /6%,1

DLE

1. Measurement points are done at CMOS levels: 0.3VDD and 0.7VDD.

DocID024295 Rev 6 79/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Figure 20. SPI timing diagram - master mode(1)

+LJK

166LQSXW

WF 6&.
6&.2XWSXW

&3+$ 
&32/ 
&3+$ 
&32/ 
6&.2XWSXW

&3+$ 
&32/ 
&3+$ 
&32/ 

WZ 6&.+ WU 6&.
WVX 0, WZ 6&./ WI 6&.
0,62
,13 87 06%,1 %,7,1 /6%,1

WK 0,
026,
06%287 % , 7287 /6%287
287387
WY 02 WK 02
DLF

1. Measurement points are done at CMOS levels: 0.3VDD and 0.7VDD.

USB characteristics
The USB interface is USB-IF certified (full speed).

Table 49. USB startup time


Symbol Parameter Max Unit

tSTARTUP(1) USB transceiver startup time 1 µs


1. Guaranteed by design.

80/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 50. USB DC electrical characteristics


Symbol Parameter Conditions Min.(1) Max.(1) Unit

Input levels

VDD USB operating voltage(2) - 3.0 3.6 V


(3)
VDI Differential input sensitivity I(USB_DP, USB_DM) 0.2 -
VCM(3) Differential common mode range Includes VDI range 0.8 2.5 V
VSE(3) Single ended receiver threshold - 1.3 2.0

Output levels

VOL(4) Static output level low RL of 1.5 kΩ to 3.6 V(5) - 0.3


V
VOH(4) Static output level high RL of 15 kΩ to VSS(5) 2.8 3.6
1. All the voltages are measured from the local ground potential.
2. To be compliant with the USB 2.0 full speed electrical specification, the USB_DP (D+) pin should be pulled
up with a 1.5 kΩ resistor to a 3.0-to-3.6 V voltage range.
3. Guaranteed by characterization results.
4. Guaranteed by test in production.
5. RL is the load connected on the USB drivers.

Figure 21. USB timings: definition of data signal rise and fall time

&URVVRYHU
SRLQWV
'LIIHUHQWLDO
GDWDOLQHV

9&56

966

WI WU
DLE

Table 51. USB: full speed electrical characteristics


Driver characteristics(1)

Symbol Parameter Conditions Min Max Unit

tr Rise time(2) CL = 50 pF 4 20 ns
(2)
tf Fall Time CL = 50 pF 4 20 ns
trfm Rise/ fall time matching tr/tf 90 110 %
VCRS Output signal crossover voltage - 1.3 2.0 V
1. Guaranteed by design.
2. Measured from 10% to 90% of the data signal. For more detailed informations, please refer to USB
Specification section 7 (version 2.0).

DocID024295 Rev 6 81/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.17 12-bit ADC characteristics


Unless otherwise specified, the parameters given in Table 53 are guaranteed by design.

Table 52. ADC clock frequency


Symbol Parameter Conditions Min Max Unit

Voltage 2.4 V ≤VDDA ≤3.6 V 16


ADC clock Range 1 &
fADC 2 1.8 V ≤VDDA ≤2.4 V 0.480 8 MHz
frequency
Voltage Range 3 4

Table 53. ADC characteristics


Symbol Parameter Conditions Min Typ Max Unit

VDDA Power supply - 1.8 - 3.6 V

Current on the VDDA input Peak - 2150


IVDDA(1) 1400 µA
pin Average - 1900
VAIN Conversion voltage range - 0(2) - VDDA V
Direct channels - - 1
12-bit sampling rate Msps
Multiplexed channels - - 0.76
Direct channels - - 1.07
10-bit sampling rate Msps
Multiplexed channels - - 0.8
fS
Direct channels - - 1.23
8-bit sampling rate Msps
Multiplexed channels - - 0.89
Direct channels - - 1.45
6-bit sampling rate Msps
Multiplexed channels - - 1
Direct channels
0.25 - -
2.4 V ≤VDDA ≤3.6 V
Multiplexed channels
0.56 - -
2.4 V ≤VDDA ≤3.6 V
µs
tS Sampling time(3) Direct channels
0.56 - -
1.8 V ≤VDDA ≤2.4 V
Multiplexed channels
1 - -
1.8 V ≤VDDA ≤2.4 V
- 4 - 384 1/fADC
fADC = 16 MHz 1 - 24.75 µs
Total conversion time 4 to 384 (sampling
tCONV
(including sampling time) - phase) +12 (successive 1/fADC
approximation)

Internal sample and hold Direct channels - -


CADC 16 pF
capacitor Multiplexed channels - -

82/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 53. ADC characteristics (continued)


Symbol Parameter Conditions Min Typ Max Unit

External trigger frequency 12-bit conversions - - Tconv+1 1/fADC


fTRIG
Regular sequencer 6/8/10-bit conversions - - Tconv 1/fADC

External trigger frequency 12-bit conversions - - Tconv+2 1/fADC


fTRIG
Injected sequencer 6/8/10-bit conversions - - Tconv+1 1/fADC
(3)
RAIN Signal source impedance - - - 50 κΩ

Injection trigger conversion fADC = 16 MHz 219 - 281 ns


tlat
latency - 3.5 - 4.5 1/fADC

Regular trigger conversion fADC = 16 MHz 156 - 219 ns


tlatr
latency - 2.5 - 3.5 1/fADC
tSTAB Power-up time - - - 3.5 µs
1. The current consumption through VDDA is composed of two parameters:
- one constant (max 1300 µA)
- one variable (max 400 µA), only during sampling time + 2 first conversion pulses.
So, peak consumption is 1300+400 = 1700 µA and average consumption is 1300 + [(4 sampling + 2) /16] x
400 = 1450 µA at 1Msps
2. VSSA must be tied to ground.
3. See Table 55: Maximum source impedance RAIN max for RAIN limitations

Table 54. ADC accuracy(1)(2)


Symbol Parameter Test conditions Min(3) Typ Max(3) Unit

ET Total unadjusted error - 2.5 4


EO Offset error 2.4 V ≤ VDDA ≤ 3.6 V - 1 2
EG Gain error fADC = 8 MHz, RAIN = 50 Ω - 1.5 3.5 LSB
ED Differential linearity error TA = -40 to 85 ° C - 1 2
EL Integral linearity error - 2 3
ENOB Effective number of bits 9.5 10 - bits
2.4 V ≤ VDDA ≤ 3.6 V
Signal-to-noise and
SINAD fADC = 16 MHz, RAIN = 50 Ω 59 62 -
distortion ratio
TA = -40 to 85 ° C dB
SNR Signal-to-noise ratio 60 62 -
Finput =10 kHz
THD Total harmonic distortion - -72 -69
ENOB Effective number of bits 9.5 10 - bits
1.8 V ≤ VDDA ≤ 2.4 V
Signal-to-noise and fADC = 8 MHz or 4 MHz,
SINAD 59 62 -
distortion ratio RAIN = 50 Ω
TA = -40 to 85 ° C dB
SNR Signal-to-noise ratio 60 62 -
Finput =10 kHz
THD Total harmonic distortion - -72 -69

DocID024295 Rev 6 83/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Table 54. ADC accuracy(1)(2) (continued)


Symbol Parameter Test conditions Min(3) Typ Max(3) Unit

ET Total unadjusted error - 2 3


EO Offset error 1.8 V ≤ VDDA ≤ 2.4 V - 1 1.5
EG Gain error fADC = 4 MHz, RAIN = 50 Ω - 1.5 2.5 LSB
ED Differential linearity error TA = -40 to 85 ° C - 1 2
EL Integral linearity error - 2 3
1. ADC DC accuracy values are measured after internal calibration.
2. ADC accuracy vs. negative injection current: Injecting a negative current on any analog input pins should be avoided as this
significantly reduces the accuracy of the conversion being performed on another analog input. It is recommended to add a
Schottky diode (pin to ground) to analog pins which may potentially inject negative currents.
Any positive injection current within the limits specified for IINJ(PIN) and ΣIINJ(PIN) in Section 6.3.12 does not affect the ADC
accuracy.
3. Guaranteed by characterization results.

Figure 22. ADC accuracy characteristics


95() 9''$
>/6%,'($/  RUGHSHQGLQJRQSDFNDJH
 
(*  ([DPSOHRIDQDFWX DOWUDQVIH UFXUYH

 7KHLGHDOWUDQVIHUFX UYH
  (QGSRLQWFRUUHODWLRQOLQH

 (7 7RWDOXQDGMXVWHG(UURUPD[LPXPGHYLDWLRQ
(7 EHWZHHQWKHDFWXDODQGWKHLGHDOWUDQVIHUFXUYHV
  (2 2IIVHW(UURUGHYLDWLRQEHWZHHQWKHILUVWDFWXDO
 WUDQVLWLRQDQGWKHODVWDFWXDORQH
 (* *DLQ(UURUGHYLDWLRQEHWZHHQWKHODVWLGHDO
 WUDQVLWLRQDQGWKHODVWDFWXDORQH
(2 (/ (' 'LIIHUHQWLDO/LQHDULW\(UURUPD[LPXPGHYLDWLRQ

EHWZHHQDFWXDOVWHSVDQGWKHLGHDORQH
 (' (/ ,QWHJUDO/LQHDULW\(UURUPD[LPXPGHYLDWLRQ
 EHWZHHQDQ\DFWXDOWUDQVLWLRQDQGWKHHQGSRLQW
/6%,'($/ FRUUHODWLRQOLQH



          
966$ 9''$
DLH

Figure 23. Typical connection diagram using the ADC

9''$ 670/[[
6DPSOHDQGKROG
$'&FRQYHUWHU
5$,1  $,1[ ELW
,/“Q$ FRQYHUWHU
&SDUDVLWLF
9$,1
&$'& 

DLH

1. Refer to Table 55: Maximum source impedance RAIN max for the value of RAIN and Table 53: ADC
characteristics for the value of CADC
2. Cparasitic represents the capacitance of the PCB (dependent on soldering and PCB layout quality) plus the
pad capacitance (roughly 7 pF). A high Cparasitic value will downgrade conversion accuracy. To remedy
this, fADC should be reduced.

84/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Figure 24. Maximum dynamic current consumption on VDDA supply pin during ADC
conversion

Sampling (n cycles) Conversion (12 cycles)

ADC clock

IDDA

1700 µA

1300 µA

MS36686V1

Table 55. Maximum source impedance RAIN max(1)


RAIN max (kOhm)
Ts Ts (cycles)
Multiplexed channels Direct channels
(µs) fADC= 16 MHz(2)
2.4 V < VDDA< 3.6 V 1.8 V < VDDA < 2.4 V 2.4 V < VDDA< 3.3 V 1.8 V < VDDA < 2.4 V

0.25 Not allowed Not allowed 0.7 Not allowed 4


0.5625 0.8 Not allowed 2.0 1.0 9
1 2.0 0.8 4.0 3.0 16
1.5 3.0 1.8 6.0 4.5 24
3 6.8 4.0 15.0 10.0 48
6 15.0 10.0 30.0 20.0 96
12 32.0 25.0 50.0 40.0 192
24 50.0 50.0 50.0 50.0 384
1. Guaranteed by design.
2. Number of samples calculated for fADC = 16 MHz. For fADC = 8 and 4 MHz the number of sampling cycles can be
reduced with respect to the minimum sampling time Ts (us).

General PCB design guidelines


Power supply decoupling should be performed as shown in Figure 8, depending on whether
VREF+ is connected to VDDA or not. The 100 nF capacitors should be ceramic (good quality).
They should be placed as close as possible to the chip.

DocID024295 Rev 6 85/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.18 DAC electrical specifications


Data guaranteed by design, unless otherwise specified.

Table 56. DAC characteristics


Symbol Parameter Conditions Min Typ Max Unit

VDDA Analog supply voltage - 1.8 - 3.6 V

Current consumption on No load, middle code (0x800) - 350 540 µA


IDDA(1) VDDA supply
VDDA = 3.3 V No load, worst code (0xF1C) - 540 870 µA

DAC output Connected to VSSA 5 - -


RL Resistive load kΩ
buffer ON Connected to VDDA 25 - -
CL Capacitive load DAC output buffer ON - - 50 pF
RO Output impedance DAC output buffer OFF 12 16 20 kΩ

VDDA –
DAC output buffer ON 0.2 - V
0.2
Voltage on DAC_OUT
VDAC_OUT
output
VDDA–
DAC output buffer OFF 0.5 - mV
1LSB

CL ≤ 50 pF, RL ≥ 5 kΩ
- 1.5 3
DAC output buffer ON
DNL(1) Differential non linearity(2)
No RL, CL ≤ 50 pF
- 1.5 3
DAC output buffer OFF
CL ≤ 50 pF, RL ≥ 5 kΩ
- 2 4
(1)
DAC output buffer ON
INL Integral non linearity(3)
No RL, CL ≤ 50 pF LSB
- 2 4
DAC output buffer OFF
CL ≤ 50 pF, RL ≥ 5 kΩ
- ±10 ±25
DAC output buffer ON
Offset(1) Offset error at code 0x800 (4)
No RL, CL ≤ 50 pF
- ±5 ±8
DAC output buffer OFF
No RL, CL ≤ 50 pF
Offset1(1) Offset error at code 0x001(5) - ±1.5 ±5
DAC output buffer OFF
VDDA = 3.3V,TA = 0 to 50 ° C
-20 -10 0
(1) Offset error temperature DAC output buffer OFF
dOffset/dT µV/°C
coefficient (code 0x800) VDDA = 3.3V, TA = 0 to 50 ° C
0 20 50
DAC output buffer ON
CL ≤ 50 pF, RL ≥ 5 kΩ +0.1 / +0.2 / -
-
DAC output buffer ON -0.2% 0.5%
Gain(1) Gain error(6) %
No RL, CL ≤ 50 pF +0 / - +0 / -
-
DAC output buffer OFF 0.2% 0.4%

86/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 56. DAC characteristics (continued)


Symbol Parameter Conditions Min Typ Max Unit

VDDA = 3.3V, TA = 0 to 50 ° C
-10 -2 0
Gain error temperature DAC output buffer OFF
dGain/dT(1) µV/°C
coefficient VDDA = 3.3V, TA = 0 to 50 ° C
-40 -8 0
DAC output buffer ON
CL ≤ 50 pF, RL ≥ 5 kΩ
- 12 30
(1)
DAC output buffer ON
TUE Total unadjusted error LSB
No RL, CL ≤ 50 pF
- 8 12
DAC output buffer OFF
Settling time (full scale: for a
12-bit code transition
between the lowest and the
tSETTLING CL ≤ 50 pF, RL ≥ 5 kΩ - 7 12 µs
highest input codes till
DAC_OUT reaches final
value ±1LSB
Max frequency for a correct
DAC_OUT change (95% of
Update rate CL ≤ 50 pF, RL ≥ 5 kΩ - - 1 Msps
final value) with 1 LSB
variation in the input code
Wakeup time from off state
tWAKEUP (setting the ENx bit in the CL ≤ 50 pF, RL ≥ 5 kΩ - 9 15 µs
DAC Control register)(7)
VDDA supply rejection ratio
PSRR+ CL ≤ 50 pF, RL ≥ 5 kΩ - -60 -35 dB
(static DC measurement)
1. Guaranteed by characterization results.
2. Difference between two consecutive codes - 1 LSB.
3. Difference between measured value at Code i and the value at Code i on a line drawn between Code 0 and last Code
4095.
4. Difference between the value measured at Code (0x800) and the ideal value = VDDA/2.
5. Difference between the value measured at Code (0x001) and the ideal value.
6. Difference between ideal slope of the transfer function and measured slope computed from code 0x000 and 0xFFF when
buffer is OFF, and from code giving 0.2 V and (VDDA – 0.2) V when buffer is ON.
7. In buffered mode, the output can overshoot above the final value for low input code (starting from min value).

DocID024295 Rev 6 87/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

Figure 25. 12-bit buffered /non-buffered DAC

%XIIHUHG1RQEXIIHUHG'$&

%XIIHU 
5/

ELW '$&B287[
GLJLWDOWR
DQDORJ
FRQYHUWHU
&/

AI6

1. The DAC integrates an output buffer that can be used to reduce the output impedance and to drive external
loads directly without the use of an external operational amplifier. The buffer can be bypassed by
configuring the BOFFx bit in the DAC_CR register.

6.3.19 Comparator

Table 57. Comparator 1 characteristics


Symbol Parameter Conditions Min(1) Typ Max(1) Unit

VDDA Analog supply voltage - 1.8 3.6 V


R400K R400K value - - 400 -

R10K R10K value - - 10 -
Comparator 1 input
VIN - 0.6 - VDDA V
voltage range
tSTART Comparator startup time - - 7 10
µs
(2)
td Propagation delay - - 3 10
Voffset Comparator offset - - ±3 ±10 mV
VDDA = 3.6 V
Comparator offset
VIN+ = 0 V
dVoffset/dt variation in worst voltage 0 1.5 10 mV/1000 h
VIN- = VREFINT
stress conditions
TA = 25 ° C
ICOMP1 Current consumption(3) - - 160 260 nA
1. Guaranteed by characterization results.
2. The delay is characterized for 100 mV input step with 10 mV overdrive on the inverting input, the non-
inverting input set to the reference.
3. Comparator consumption only. Internal reference voltage not included.

88/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Electrical characteristics

Table 58. Comparator 2 characteristics


Symbol Parameter Conditions Min Typ Max(1) Unit

VDDA Analog supply voltage - 1.8 - 3.6 V


VIN Comparator 2 input voltage range - 0 - VDDA V
Fast mode - 15 20
tSTART Comparator startup time
Slow mode - 20 25
1.8 V ≤VDDA ≤2.7 V - 1.8 3.5
td slow Propagation delay(2) in slow mode µs
2.7 V ≤VDDA ≤3.6 V - 2.5 6
1.8 V ≤VDDA ≤2.7 V - 0.8 2
td fast Propagation delay(2) in fast mode
2.7 V ≤VDDA ≤3.6 V - 1.2 4
Voffset Comparator offset error - - ±4 ±20 mV
VDDA = 3.3V
TA = 0 to 50 ° C
dThreshold/ Threshold voltage temperature V- = VREFINT, ppm
- 15 100
dt coefficient 3/4 VREFINT, /°C
1/2 VREFINT,
1/4 VREFINT
Fast mode - 3.5 5
ICOMP2 Current consumption(3) µA
Slow mode - 0.5 2
1. Guaranteed by characterization results.
2. The delay is characterized for 100 mV input step with 10 mV overdrive on the inverting input, the non-
inverting input set to the reference.
3. Comparator consumption only. Internal reference voltage (necessary for comparator operation) is not
included.

DocID024295 Rev 6 89/103


90
Electrical characteristics STM32L100C6 STM32L100R8/RB

6.3.20 LCD controller


The STM32L100C6 and STM32L100R8/RB devices embed a built-in step-up converter to
provide a constant LCD reference voltage independently from the VDD voltage. An external
capacitor Cext must be connected to the VLCD pin to decouple this converter.

Table 59. LCD controller characteristics


Symbol Parameter Min Typ Max Unit

VLCD LCD external voltage - - 3.6


VLCD0 LCD internal reference voltage 0 - 2.6 -
VLCD1 LCD internal reference voltage 1 - 2.73 -
VLCD2 LCD internal reference voltage 2 - 2.86 -
VLCD3 LCD internal reference voltage 3 - 2.98 - V
VLCD4 LCD internal reference voltage 4 - 3.12 -
VLCD5 LCD internal reference voltage 5 - 3.26 -
VLCD6 LCD internal reference voltage 6 - 3.4 -
VLCD7 LCD internal reference voltage 7 - 3.55 -
Cext VLCD external capacitance 0.1 - 2 µF
Supply current at VDD = 2.2 V - 3.3 -
ILCD(1) µA
Supply current at VDD = 3.0 V - 3.1 -
RHtot(2) Low drive resistive network overall value 5.28 6.6 7.92 MΩ
(2)
RL High drive resistive network total value 192 240 288 kΩ
V44 Segment/Common highest level voltage - - VLCD V
V34 Segment/Common 3/4 level voltage - 3/4 VLCD -
V23 Segment/Common 2/3 level voltage - 2/3 VLCD -
V12 Segment/Common 1/2 level voltage - 1/2 VLCD -
V
V13 Segment/Common 1/3 level voltage - 1/3 VLCD -
V14 Segment/Common 1/4 level voltage - 1/4 VLCD -
V0 Segment/Common lowest level voltage 0 - -
Segment/Common level voltage error
ΔVxx(2) - - ± 50 mV
TA = -40 to 85 ° C
1. LCD enabled with 3 V internal step-up active, 1/8 duty, 1/4 bias, division ratio= 64, all pixels active, no LCD
connected
2. Guaranteed by characterization results.

90/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Package information

7 Package information

In order to meet environmental requirements, ST offers these devices in different grades of


ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.

7.1 LQFP64 10 x 10 mm, 64-pin low-profile quad flat package


information
Figure 26. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package outline

6($7,1*3/$1(
&
$
$

PP
*$8*(3/$1(
$

F
FFF &

$
' .
' /
' /
 




E
(
(

 

3,1  
,'(17,),&$7,21 H
:B0(B9

1. Drawing is not to scale.

Table 60. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package mechanical
data
millimeters inches(1)
Symbol
Min Typ Max Typ Min Max

A - - 1.600 - - 0.0630
A1 0.050 - 0.150 0.0020 - 0.0059
A2 1.350 1.400 1.450 0.0531 0.0551 0.0571

DocID024295 Rev 6 91/103


102
Package information STM32L100C6 STM32L100R8/RB

Table 60. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package mechanical
data (continued)
millimeters inches(1)
Symbol
Min Typ Max Typ Min Max

b 0.170 0.220 0.270 0.0067 0.0087 0.0106


c 0.090 - 0.200 0.0035 - 0.0079
D - 12.000 - - 0.4724 -
D1 - 10.000 - - 0.3937 -
D3 - 7.500 - - 0.2953 -
E - 12.000 - - 0.4724 -
E1 - 10.000 - - 0.3937 -
E3 - 7.500 - - 0.2953 -
e - 0.500 - - 0.0197 -
K 0° 3.5° 7° 0° 3.5° 7°
L 0.450 0.600 0.750 0.0177 0.0236 0.0295
L1 - 1.000 - - 0.0394 -
ccc - - 0.080 - - 0.0031
1. Values in inches are converted from mm and rounded to 4 decimal digits.

Figure 27. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package recommended
footprint

 


  






 


 





AIC

1. Dimensions are in millimeters.

92/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Package information

LQFP64 device marking


The following figure gives an example of topside marking orientation versus pin 1 identifier
location.
Other optional marking or inset/upset marks, which identify the parts throughout supply
chain operations, are not indicated below.

Figure 28. LQFP64 10 x 10 mm, 64-pin low-profile quad flat package top view example

3URGXFWLGHQWLILFDWLRQ  5HYLVLRQFRGH

5
670/
5%7

'DWHFRGH
< ::
3LQ
LQGHQWLILHU

06Y9

1. Parts marked as ES or E or accompanied by an engineering sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples in
production. ST’s Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

DocID024295 Rev 6 93/103


102
Package information STM32L100C6 STM32L100R8/RB

7.2 UFQFPN48 7 x 7 mm, 0.5 mm pitch, package information


Figure 29. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package outline
3LQLGHQWLILHU
ODVHUPDUNLQJDUHD
'

$
( (
7 6HDWLQJ
SODQH
GGG $
H E

'HWDLO<
'
<

([SRVHGSDG
DUHD '


/

&[ƒ
SLQFRUQHU 5W\S

( 'HWDLO=


=
$%B0(B9

1. Drawing is not to scale.


2. All leads/pads should also be soldered to the PCB to improve the lead/pad solder joint life.
3. There is an exposed die pad on the underside of the UFQFPN package. It is recommended to connect and
solder this back-side pad to PCB ground.

94/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Package information

Table 61. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package mechanical data


millimeters inches(1)
Symbol
Min Typ Max Min Typ Max

A 0.500 0.550 0.600 0.0197 0.0217 0.0236


A1 0.000 0.020 0.050 0.0000 0.0008 0.0020
D 6.900 7.000 7.100 0.2717 0.2756 0.2795
E 6.900 7.000 7.100 0.2717 0.2756 0.2795
D2 5.500 5.600 5.700 0.2165 0.2205 0.2244
E2 5.500 5.600 5.700 0.2165 0.2205 0.2244
L 0.300 0.400 0.500 0.0118 0.0157 0.0197
T - 0.152 - - 0.0060 -
b 0.200 0.250 0.300 0.0079 0.0098 0.0118
e - 0.500 - - 0.0197 -
ddd - - 0.080 - - 0.0031
1. Values in inches are converted from mm and rounded to 4 decimal digits.

Figure 30. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package recommended footprint





 

 

 








 

 

 


!"?&0?6

1. Dimensions are in millimeters.

DocID024295 Rev 6 95/103


102
Package information STM32L100C6 STM32L100R8/RB

UFQFPN48 device marking


The following figure gives an example of topside marking orientation versus pin 1 identifier
location.
Other optional marking or inset/upset marks, which identify the parts throughout supply
chain operations, are not indicated below.

Figure 31. UFQFPN48 7 x 7 mm, 0.5 mm pitch, package top view example

3URGXFW

LGHQWLILFDWLRQ 45.-

$6

'DWHFRGH

: 88
3LQ
5HYLVLRQFRGH
LGHQWLILFDWLRQ
3

069

1. Parts marked as ES or E or accompanied by an engineering sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples in
production. ST’s Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

96/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Package information

7.3 Thermal characteristics


The maximum chip-junction temperature, TJ max, in degrees Celsius, may be calculated
using the following equation:
TJ max = TA max + (PD max × ΘJA)
Where:
• TA max is the maximum ambient temperature in ° C,
• ΘJA is the package junction-to-ambient thermal resistance, in ° C/W,
• PD max is the sum of PINT max and PI/O max (PD max = PINT max + PI/Omax),
• PINT max is the product of IDD and VDD, expressed in Watts. This is the maximum chip
internal power.
PI/O max represents the maximum power dissipation on output pins where:
PI/O max = Σ (VOL × IOL) + Σ((VDD – VOH) × IOH),
taking into account the actual VOL / IOL and VOH / IOH of the I/Os at low and high level in the
application.

Table 62. Thermal characteristics


Symbol Parameter Value Unit
Thermal resistance junction-ambient
45
LQFP64 - 10 x 10 mm / 0.5 mm pitch
ΘJA °C/W
Thermal resistance junction-ambient
33
UFQFPN48 - 7 x 7 mm / 0.5 mm pitch

Figure 32. Thermal resistance




)RUELGGHQDUHD
7- !7-PD[


3' P:
 /4)3
8)4)31





     

7HPSHUDWXUH ƒ&
069

DocID024295 Rev 6 97/103


102
Package information STM32L100C6 STM32L100R8/RB

7.3.1 Reference document


JESD51-2 Integrated Circuits Thermal Test Method Environment Conditions - Natural
Convection (Still Air). Available from www.jedec.org.

98/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Ordering information

8 Ordering information

Table 63. Ordering information scheme

Example: STM32 L 100 C 8 T 6 TR

Device family
STM32 = ARM-based 32-bit microcontroller

Product type
L = Low power

Device subfamily
100

Pin count
C = 48 pins
R = 64 pins

Flash memory size


6 = 32 Kbytes of Flash memory
8 = 64 Kbytes of Flash memory
B = 128 Kbytes of Flash memory

Package
T = LQFP
U = UFQFPN

Temperature range
6 = Industrial temperature range, –40 to 85 °C

Packing
TR = tape and reel
No character = tray or tube

For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST sales office.

DocID024295 Rev 6 99/103


102
Revision history STM32L100C6 STM32L100R8/RB

9 Revision history

Table 64. Document revision history


Date Revision Changes

21-Feb-2013 1 Initial release.


Updated max. RAM size from 10 to 16 Kbytes
Changed number of wakeup pins from 3 to 2 throughout the
document.
Added Section 6.1.7: Optional LCD power supply scheme.
Removed first sentence in I2C interface characteristics
Moved Table 14: Embedded internal reference voltage calibration
values (previously in Section 3.10.1: Internal voltage reference
(VREFINT) with title “Internal voltage reference measured values”).
Replaced “Σ” with “σ” in Section 6.1.1 and 6.1.2.
Updated LCD and ADC features in Table 1: Ultra-low-power
STM32L100C6 and STM32L100R8/RB device features and
peripheral counts.
Updated fHSE conditions in Table 16: Current consumption in Run
mode, code with data processing running from Flash and Table 17:
Current consumption in Run mode, code with data processing
31-Mar-2014 2 running from RAM.
Fixed IDD unit in Table 22: Typical and maximum current
consumptions in Standby mode.
Modified title of Table 27: HSE oscillator characteristics.
Modified title of Table 24: Low-power mode wakeup timings.
Section 6.3.5: Wakeup time from Low-power mode was previously a
paragraph in Section 6.3.4: Supply current characteristics.
Modified introduction of Section 6.3.4: Supply current
characteristics.
Added paragraph below title High-speed external user clock
generated from an external source.
Added 2 bullets on page 50.
Moved Figure 11: High-speed external clock source AC timing
diagram (was previously after Figure 12: Low-speed external clock
source AC timing diagram).
Updated Figure 29 footnote numbering.

100/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB Revision history

Table 64. Document revision history (continued)


Date Revision Changes

Deleted second footnote in Figure 30.


Updated Section 6.3.11: Electrical sensitivity characteristics title.
Updated section link in second paragraph of Section 6.3.15: TIM
timer characteristics.
Removed all occurrences of “when 8 pins are sourced at same
time” in Table 42: Output voltage characteristics.
Modified first sentence in Section 6.3.14: NRST pin characteristics.
Updated text and removed figure Power supply and reference
decoupling in General PCB design guidelines.
Updated sub-section TIM10, TIM11 and TIM9.
In Table 58: Comparator 2 characteristics, parameter dThreshold/dt,
replaced all occurrences of “VREF+” with “VREFINT”.
Updated:
– Table 4: Working mode-dependent functionalities (from
Run/active down to standby)
– Table 5: Timer feature comparison
– Table 7: STM32L100C6 and STM32L100R8/RB pin definitions
– Table 9: Voltage characteristics
– Table 12: General operating conditions
– Table 15: Embedded internal reference voltage
– Table 25: High-speed external user clock characteristics
– Table 28: LSE oscillator characteristics (fLSE = 32.768 kHz)
31-Mar-2014
2 – Table 29: HSI oscillator characteristics
(continued)
– Table 38: ESD absolute maximum ratings
– Table 40: I/O current injection susceptibility
– Table 41: I/O static characteristics
– Table 42: Output voltage characteristics
– Table 44: NRST pin characteristics
– Table 61: UFQFPN48 7 x 7 mm, 0.5 mm pitch, package
mechanical data
– Table 62: Thermal characteristics, Table 53: ADC characteristics
Updated:
– Figure 6: Pin loading conditions
– Figure 7: Pin input voltage
– Figure 8: Power supply scheme
– Figure 10: Current consumption measurement scheme
– Figure 17: I2C bus AC waveforms and measurement circuit
– Figure 23: Typical connection diagram using the ADC
– Figure 32: Thermal resistance
Added:
– Figure 28: LQFP64 10 x 10 mm, 64-pin low-profile quad flat
package top view example
– Figure 31: UFQFPN48 7 x 7 mm, 0.5 mm pitch, package top view
example
– Table 6: Legend/abbreviations used in the pinout table
10-Apr-2014 3 Updated 10 KB RAM in Cover & description.

DocID024295 Rev 6 101/103


102
Revision history STM32L100C6 STM32L100R8/RB

Table 64. Document revision history (continued)


Date Revision Changes

Updated DMIPS features in cover page and Section 2: Description.


Updated Table 23: Peripheral current consumption with new
measured values.
Updated Table 55: Maximum source impedance RAIN max adding
30-Jan-2015 4 note 2.
Updated Section 7: Package information with new package device
marking.
Updated Figure 5: Memory map.
Updated Table 63: Ordering information scheme.
Updated Section 7: Package information structure: Paragraph titles
and paragraph heading level.
Updated Table 60: LQFP64 10 x 10 mm, 64-pin low-profile quad flat
package mechanical data.
Updated Section 7: Package information for LQFP64 and
UFQFPN48 package device markings, adding text for device
orientation versus pin 1 identifier.
Updated Table 15: Embedded internal reference voltage
temperature coefficient at 100ppm/°C and table note 3: ‘guaranteed
by design’ changed by ‘guaranteed by characterization results’.
28-Apr-2016 5 Updated Table 58: Comparator 2 characteristics new maximum
threshold voltage temperature coefficient at 100ppm/°C.
Updated Table 38: ESD absolute maximum ratings CDM class.
Updated all the notes, removing ‘not tested in production’.
Updated Table 9: Voltage characteristics adding note about VREF-
pin.
Updated Table 2: Functionalities depending on the operating power
supply range LSI and LSE functionalities putting “Y” in Standby
mode.
Removed note 1 below Figure 2: Clock tree.
Updated Table 56: DAC characteristics resistive load.
Updated Section 7: Package information adding information about
other optional marking or inset/upset marks.
Updated note 1 below all the package device marking figures.
Updated Nested vectored interrupt controller (NVIC) in Section 3.2:
ARM® Cortex®-M3 core with MPU about process state
automatically saved.
Updated Table 2: Functionalities depending on the operating power
supply range removing I/O operation column and adding note about
GPIO speed.
28-Aug-2017 6
Updated Table 40: I/O current injection susceptibility note by
‘injection is not possible’.
Updated Figure 16: Recommended NRST pin protection note about
the 0.1uF capacitor.
Updated Section 3.1: Low-power modes Low-power run mode
(MSI) RC oscillator clock.
Updated Table 4: Working mode-dependent functionalities (from
Run/active down to standby) disabling I2C functionality in Low-
power Run and Low-power Sleep modes.

102/103 DocID024295 Rev 6


STM32L100C6 STM32L100R8/RB

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2017 STMicroelectronics – All rights reserved

DocID024295 Rev 6 103/103


103

You might also like