CS 1 / CAS 1 in A-dec 200

EN

Assembly instructions
 Content

Important Information
1. Instructions ������������������������������������������� 4
2. Delivery Contents ��������������������������������� 4

Mounting EN
3. Prepare treatment unit ������������������������� 5
4. Installation of Rinsing Unit ������������������� 5
4.1 Rinsing Unit Vario ����������������������������� 5
4.2 Rinsing Unit 1 ����������������������������������� 6
5. Mounting the CS 1 ��������������������������������� 7
6. Mounting the CAS 1 ����������������������������� 9
7. Rinsing Unit water connection ����������� 11
8. Securing the relay box ����������������������� 11
9. Electrical connection ������������������������� 11
9.1 Connection plan for CS 1 ��������������� 12
9.2 Connection plan for CAS 1 ������������� 12
10. Closing works ������������������������������������� 13

2015/05 3
 Important
Information
1. Instructions
The following information supplements
the information in the installation and
operating instructions for the appli-
ances.

The information in the Installation and Operating

EN Instructions must also be observed. These con-
tain important informations, e.g. Safety Instruc-
tions, Set-up, Electrical Connection,
Disinfection, Cleaning, etc.
The Installation and Operating Instructions are
delivered with the appliance.

2. Delivery Contents
CS 1 for A-dec 200���������������������������� 7117-61

Contents:
• Conversion set (mounting plate, Dürr Connect
plumbing parts, hoses, screws, relay box, ca-
ble)
• CS 1 with integrated station selection valve
• Vario Rinsing Unit
• Assembly instructions

CAS 1 for A-dec 200�������������������������� 7117-27

Contents:
• Conversion set (mounting plate, Dürr Connect
plumbing parts, hoses, screws, relay box, ca-
ble)
• CS 1 with integrated station selection valve
• Vario Rinsing Unit
• Assembly instructions

4 2015/05
 Mounting

3. Prepare treatment unit

WARNING
Electric shock when live parts are
touched or damage on contact with
water
• Before commencing any conversion
work disconnect all power to the
treatment unit and switch off air, water EN
and suction unit connections.

• Remove the housing.

1
• Place the Dürr Connect assembly onto the
waste water system drain pipe (1) of the spit-
toon and secure with clips.
• Place the suction hose (2) with hose joint pi-
ece and rinse connection onto the suction
connection parts and secure with cable ties.
1

4. Installation of Rinsing
Unit
Installation of the Rinsing Unit onto the
mounting plate is the same for both
CS 1 and CAS 1

4.1 Rinsing Unit Vario

• Secure the rinsing unit onto the mounting
plate using two M3 x 8 screws as illustrated in
fig.3.

3
2015/05 5
 4.2 Rinsing Unit 1
Fit the mounting plate for the Rinsing Unit 1
in place
• Fit the mounting plate (13) for the Rinsing Unit
1 onto the mounting plate (12) for the CAS 1/
CS 1 using the M3 x 8 screws (14)
12
Assemble the Rinsing Unit 1
• Fix the Rinsing Unit 1 onto the mounting plate
(13) for the Rinsing Unit 1 using the M5 x 10
screw (15).
EN

13
4 14

Assemble the Rinsing Unit water

connection
• Cut the hose (16) cleanly
• Slide the locking nut (19) and the olive (18)
onto the hose (16).
• Slide the connection sleeve (17) into the hose
(16).
• Screw the locking nut with the hose to the
Rinsing Unit tightly.

15

Rinsing Unit water connection

• Please see chapter 7 of the Assembly instruc-
tions for CAS 1/CS 1 in A-dec 200

Rinsing Unit electrical connections

• Please see chapter 9 of the Assembly instruc-
17 tions for CAS 1/CS 1 in A-dec 200

18

19

16
6
6 2015/05
 5. Mounting the CS 1
CAUTION
Electrostatic discharge
Working on sensitive components, e.g.
printed circuit board, can lead to elec-
trostatic discharge. The function of the-
se components can be destroyed lea-
ding to breakdown of the unit involved.
• Before beginning to replace the prin-
ted circuit board carry out an electro-
static discharge with the aid of the
earthed wrist strap.
EN
• Screw the CS 1 tightly onto the mounting
plate using two M4 x 8 hex. socket screws as
illustrated in fig.4.
7

• Place the waste water system assembly (3)

onto the drain connection of the CS 1.
• Connect the overflow pipe (4) between the rin-
sing unit overflow and the waste water as-
sembly and secure with cable ties.
• Prepare the spittoon drainage hose (5) using
hose connection parts and place in position
on the waste water system assembly.

8 4

• Remove the electronic circuit board to the

treatment unit from its mounting.
• Hang the mounting plate with the CS 1 inside
the treatment unit and secure using two
M5 x 10 (6) screws and flat washers.
• Secure the electronic circuit board in place.
6

9
2015/05 7
 • Slide the suction hose (2) onto the CS 1 suc-
tion connections.
• Connect the rinsing hose (7) to the rinse con-
nection and to the rinsing unit.

EN
7

10

• Place the filter (8) onto the waste water sy-

stem of the spittoon.
• Place mounting (9) in position and secure
using two M3 x 30 screws.

9 • Slide the waste water hose (5) to filter draina-

ge hose.

11 5

8 2015/05
 6. Mounting the CAS 1
ACHTUNG
Electrostatic discharge
Working on sensitive components, e.g.
printed circuit board, can lead to elec-
trostatic discharge. The function of the-
se components can be destroyed lea-
ding to breakdown of the unit involved.
• Before beginning to replace the prin-
ted circuit board carry out an electro-
static discharge with the aid of the
earthed wrist strap.
EN
• Screw the CS 1 tightly onto the mounting
plate using two M4 x 8 hex. socket screws as
illustrated in fig.9.
12

• Remove the yellow filter at the inlet connec-

tions (10).
• Place the drainage hose (5) from the spittoon
with the bleeder valve (11) onto the inlet con-
11
nections (10) and secure with clips.

10

13

• Connect the overflow pipe (4) between the rin-

sing unit overflow and the waste water as-
sembly and secure with cable ties.

14
2015/05 9
 • Remove the electronic circuit board to the
treatment unit from its mounting.
• Hang the mounting plate with the CAS 1 in-
side the treatment unit and secure using two
M5 x 10 (6) screws and flat washers.
• Secure the electronic circuit board in place.
6

EN

15

• Slide the suction hose (2) onto the CAS 1 suc-

tion connections.
• Connect the rinsing hose (7) to the rinse con-
nection and to the rinsing unit.

16

• Place the filter (8) onto the waste water sy-

stem of the spittoon.
• Place mounting (9) in position and secure
using two M3 x 30 screws.
9
• Slide the waste water hose (5) to filter draina-
ge hose.

17
10 2015/05
 7. Rinsing Unit water
connection
• Divide the Tecalan water supply hose.
• Insert the bronze distributor part into the sup-
ply hose.
• Feed the Tecalan hose from the distributor
part to the rinsing unit and connect.

EN

19

8. Securing the relay box

• Stick the relay box using double sided adhe-
sive tape to a suitable position on the control
electronics mounting plate in the treatment
unit.

18

9. Electrical connection
The following elements must be connected
electrically according to the circuit diagram be-
low:
1 "WAGO" terminals
2 CS 1
3 CAS 1
5 Relay box
6 A-dec 200 PCB (main board)
7 Suction unit control unit

Further information can be found in the

appliance Installation and Operating In-
structions

2015/05 11
 9.1 Connection plan for CS 1
24V AC
5 6 Incoming Power
(alternatively) 2
Dürr CS 1
1 Main circuit board
P
X2 X1 X1 X2 X3
0 VAC 24 VAC
4 5

Fuse

EN

9.2 Connection plan for CAS 1

24V AC
5 6 Incoming Power
(alternatively) 3
Dürr CAS 1
1 Main circuit board
P
X2 X1 X1 X2 X3.1 X3.2
0 VAC 24 VAC
4 5

Fuse

12 2015/05
10. Closing works
• Check that all Dürr Connect connection parts
are secured using safety clips. Don't forget
to check O-rings.
• Carry out a check of all functions as described
in the Installation and Operating Instructions.
• Carry out an electrical safety check and re-
cord results.
• Replace all panels of the treatment unit.
• Instruct all surgery personnel how to use and
take care of the unit.
EN

2015/05 13
DÜRR DENTAL SE
Höpfigheimer Str. 17
74321 Bietigheim-Bissingen
Germany
Fon: +49 7142 705-0
www.duerrdental.com
[email protected]