Appendix 1 DOC-100 PCB

① CA connector : 18 PIN
◆ Function : CAR side input signal & DOOR input/output signal
PIN NO. Function LABEL ADDRESS
1 Door Open output D2OP 0x48083(H)
2 Door Close output D2CL 0x48084(H)
3 HCL(Output for disabled person) HCL 0x48085(H)
4 Nud. output(Nud. CLOSE, SPD 1/2, Force 2 times) NUDGE 0x48086(H)
5 DLD(Door load input) DLD 0x48015(H)
6 DMC(Door Machine Cut Off switch) DMC
7 DOLS(Door Open Limit input) DOLS 0x4802D(H)
8 CDS(CAR Door Switch input) CDS 0x4802B(H)
9 RBLDC(Backup Door Zone input) RBLDC
10 RLDC(Door Zone input) RLDC 0x48025(H)
11 COM-DZ COM-DZ
12 SES(Safety Shoe) SES 0x4802F(H)
13 M-UP(Maint Up Switch) M-UP 0x48013(H)
14 M-DN(Maint Down Switch) M-DN 0x48014(H)
15 R/S(Emergency Stop Swi+G38tch) R/S
16 R1MM (MSK running Mode input) R1MM 0x48012(H)
17 DOOR ERROR (Door Error input) DOOR-ERR
18 RDMC (DMC Switch state input) RDMC 0x48092(H)

② CB Connector : 8 PIN
◆ Function : Switch input of car side
PIN NO. Function Type ADDRESS
1 R4FS (Fire operation input) Byte 0x48043(H)
2 R4EQ (Earthquake operation input) Byte 0x48046(H)
3 LDU(Landing Device Up) Byte 0x48027(H)
4 LDD(Landing Device Down) Byte 0x48028(H)
5 R4FM (FIRE MAN SWITCH) Byte 0x48044(H)
6 INP-SP 8 Byte
7 INP-SP 7 Byte
8 Unused
③ AA Connector : 8 PIN
◆ Function : Input in Control Panel
NO Function Type ADDRESS
1 RSC(Safety system TRM input) Byte 0x48001(H)
2 INP-SP4 Byte
3 INP-SP5 Byte
4 C7NP(Normal power checking input) Byte
5 E-BAT(Emergency power: for buzzer)
6 E-GND(Emergency power: for buzzer)
7 RC1ST(Main Contactor Contact input) Byte 0x4802A(H)
8 RC1BR(Brake Contact input) Byte 0x48029(H)
④ AC Connector : 8 PIN
◆ Function : Output in Control Panel (RELAY DRIVE)
PIN NO Function Type ADDRESS
1 OUT-SP9 Byte
2 OUT-SP8 Byte
3 OUT-SP7 Byte
4 OUT-SP6 Byte
5 OUT-SP5 Byte
6 OUT-SP4 Byte
7 Unused
8 Unused
⑤ AB Connector : 18 PIN
◆ Function : Output(relay drive) & input in Control Panel
PIN NO Function Type ADDRESS
1 P48 (DC48V power source)
2 R1ML(Slack rope compen. output) Byte 0x48087(H)
3 CIST Drive (Without slack rope compen. ) Byte 0x48081(H)
4 CIST Drive (With slack rope compen.)
5 R7FN (Car Fan driving output) Byte 0x4808A(H)
6 DIFN (Inveter Fan driving output) Byte 0x4808B(H)
7 R7LF (Car Light driving output) Byte 0x48089(H)
8 CAC (Car Aircon Control) Byte 0x48088(H)
9 D-FER (Fire Emergency Relay Drive ) Byte
10 C1BR (Motor Brake output) Byte 0x48080(H)
11 G48 (DC48V power GND)
12 R4F1 (Phase1 fire oper.output) Byte 0x4808C(H)
13 R4F2 (Phase2 fire oper.output) Byte 0x4808D(H)
14 R1HI (High SPD running check output) Byte 0x48093(H)
15 LDS (Landing Door Switch input) Byte 0x4802C(H)
16 R5SX (Mechanical safety input) Byte 0x48011(H)
17 MON (DOOR 2/3 position detecting input) Byte
18 INP-SP6 1
⑥ HA Connector : 10 PIN
◆ Function : Hoistway Terminal limit switch input
PIN NO Function Bit ADDRESS
1 DL(Down Limit Switch) 15 0x48004(H)
2 SD1D(Slow Down Switch 1D) 1 0x48023(H)
3 SD2D(Slow Down Switch 2D) 3 0x48024(H)
4 SD3D(Slow Down Switch 3D) 5
5 UL(UP Limit Switch) 14 0x48003(H)
6 SD1U(Slow Down Switch 1U) 0 0x48021(H)
7 SD2U(Slow Down Switch 1U) 2 0x48022(H)
8 SD3U(Slow Down Switch 1U) 4
9 INP-SP1 12
10 INP-SP2 13
 ⑦ TB1 : Terminal Block

◆ Function : DC power supply in DOC-100 PCB

PIN NO. Function

1 VCC(+5V : main source)
2 VCC(+5V : main source)
3 V15(+15V : R/E power & HIC-108 main voltage)
4 GND
5 GND
6 FG (DC48V GND)

⑧ SD : Connector 9 PIN ⑨ ST : Connector 9 PIN

◆ Function : RS-232 Serial Port ◆ Function : RS-232 Serial Port

(For R & D) (For voice synthesizer)

PIN NO. Function PIN NO. Function

1 Unused 1 Unused
2 Tx(Tx for terminal) 2 Tx(Tx for parallel running)

3 Rx(Rx for terminal) 3 Rx(Rx for parallel running)

4 Unused 4 Unused
5 GND(signal ground) 5 GND(signal ground)
6 Unused 6 Unused
7 Unused 7 Unused
8 Unused 8 Unused
9 Unused 9 Unused

⑩ AD Connector : 4PIN ⑪ SH Connector : 4 PIN

◆ Function : Rotary Encoder ◆ Function : Hall Board

Power & Signal For G/A communication.

PIN NO. Function PIN NO. Function

1 V15(+15V : R/E power) 1 Com. line 1:for E/L.1
2 GND 2 Com. line 2:for E/L.1
3 ΦA(R/E A-phase) 3 Com. line 1:for E/L.2
4 ΦB(R/E B-phase) 4 Com. line 2:for E/L.2
⑫ SM Connector : 4 PIN ⑬ SC Connector : 2 PIN

◆ Function : For CRT & DAS G/A com. ◆ Function : For CAR LON com.

PIN NO. Function PIN NO. Function

1 Com. line 1:for E/L.1 1 Com. line 1
2 Com. line 2:for E/L.1 2 Com. line 2
3 Com. line 1:for E/L.2
4 Com. line 2:for E/L.2
DOP-100 PCB
① MNL Connector Cable & Usage(Control TRANS input)

Connector Cable Voltage Usage

01 f AC 110V DOC-100, SMPS for DPC-100 PCB, GATE TRANS power

02 H1 AC 220V HALL SMPS input power(for 16 Floor or below)

03 DT 3Φ 100V DOOR MOTOR & PCB power

04 a AC 100V INV FAN,H/L,CVT power

05

PA 06 H2 AC 220V HALL SMPS input power(for 16 Floor or below)

07

08

09 g AC 110V DOC-100,SMPS for DPC-100 PCB, GATE TRANS power

10 DR 3Φ 100V DOOR MOTOR & PCB power

11 DS 3Φ 100V DOOR MOTOR & PCB power

12 b AC 100V INV FAN,H/L,CVT power

01 YT 3Φ 37V RELAY driving,External input I/F signal,Switch signal source

02 e 3Φ 18V CAR LON PCB power

03 d 3Φ 18V

04

05

PB 06 c 3Φ 18V CAR LON PCB power

07 XT 3Φ 85V BRAKE COIL,For Contactor driving

08

09 YS 3Φ 37V RELAY driving,External input I/F signal,Switch signal source

10 XR 3Φ 85V BRAKE COIL,For Contactor driving

11 XS 3Φ 85V

12 YR 3Φ 37V RELAY driving,External input I/F signal,Switch signal source

② MIC Connector Cable & Usage
Connector Cable Voltage Usage

01 a AC 100V INV FAN, H/L, CVT power FUSE secondary side

02 DR DOOR MOTOR & PCB power FUSE secondary side

03 DS 3Φ100V

UA 04 DT DOOR MOTOR & PCB power

05 H2 HALL SMPS input power(for 16 Floor or below)

AC 220V
06 H1 HALL SMPS input power(for 16 Floor or below) FUSE secondary side

07 f DOC-100,SMPS for DPC-100 PCB,GATE TRANS power

FUSE secondary side

08 b INV FAN, H/L, CVT power FUSE secondary side

09 g DOC-100,SMPS for DPC-100 PCB,GATE TRANS power

01 G48 DC 48V GND

02 G24C DC 24V GND

UB 03 D110 DC 110V BRAKE COIL,Contactor driving power

04 D48 DC 48V RELAY driving,External input I/F signal,Switch signal source

05 G110 DC 110V GND

06

07 D24C DC 24V Power for CAR LON PCB

01

02 HHPS2 HALL SMPS power(for 16 Floor or below)

03 LT2 Building side supplied lighting power

UC 04 LT1-2 AC 220V B/D side supplied light power FUSE secondary side

05 LT1-2 B/D side supplied light power FUSE secondary side

06 HHPS1-1 HALL SMPS power(for 16 Floor or higher) FUSE primary side

07 HHPS1-2 HALL SMPS power(for 16 Floor or higher) FUSE secondary side

08 LT1-1 B/D side supplied light power FUSE primary side

09 LT1-1 B/D side supplied light power FUSE primary side

DCL-200 PCB
Tab.1) CCN1 Connector Signal

Connector PIN NO Contents Remarks

CCN1 1 COMM PORT A
2 COMM PORT B
3 GROUND from CP
4 VCC24 from CP DC 24V input
5 COMM PORT A No.1 PIN COMMON
6 COMM PORT B No.1 PIN COMMON
Tab.2) Car call button input(CBx) & LAMP output(CLx) Signal

Connector PIN NO Contents Remarks

CB1 1 CAR CALL BUTTON Input 1FL
: :
8 CAR CALL BUTTON Input 8FL
9 GROUND
CL1 1 CAR CALL BUTTON LAMP 1FL
: :
8 CAR CALL BUTTON LAMP 8FL
9 VCC24
10 VCC24
※ CB1:1~8FL,CB2:9~16FL,CB3:17~24FL,CB4:25~32FL
CL1:1~8FL,CL2:9~16FL,CL3:17~24FL,CL4:25~32FL
OPB switch, Car load detecting device(CIN), On-car connection box switch input signal
Connector PIN NO Contents Remarks
CIN 1
2 HIGH
3 IN CAR
4 DCO
5 ATT
6 INDE
7 PARK
8 EFS
9 DOWN BUTTON
10 UP BUTTON
11 START
12 BYPASS
13 CALL PRIORITY
14 FIRE 1
15 FIRE 2
16 RESCUE
17 REST
18 CAR NON STOP1
19 CAR NON STOP2
20 WD20
21 WD80
22 WD110
23 GROUND
24 GROUND
ONC 1 VCC24
2 ON CAR
3 ON CAR CLOSE
4 ON CAR UP
5 ON CAR DOWN
6 PHOTO SHOE
7 SPARE
8 110% BUZZER
9 CHIME 1
10 CHIME 2
11 GONG REVERSE Diode
12 GROUND
13 48V IN
14 48V OUT
 Tab.4) OPB LAMP output Signal
Connector PIN NO Contents Remarks
LAMP 1 OPB UP LAMP
2 OPB DOWN LAMP
3 OPB FULL LAMP
4 VCC24
5 VCC24

Tab.5) CPI output signal

Connector PIN NO Contents Remarks
IND 1 VCC24
2 GROUND
3 CPI Serial data
4 CPI Serial clock
5 CPI Serial Enable
Tab.6) Differential trs input signal
Connector PIN Contents Remarks
DFTR 1 DFTR 1 CHANNEL 1A
2 DFTR 1 CHANNEL 1B
3 DFTR 1 CHANNEL 2A
4 DFTR 1 CHANNEL 2B
5 DFTR 2 CHANNEL 1A
6 DFTR 2 CHANNEL 1B
7 DFTR 2 CHANNEL 2A
8 DFTR 2 CHANNEL 2B
9
10
Tab.7) LCD output signal
Connector PIN NO Contents Remarks
LCD 1 GROUND
2 VCC5
3 CONTRAST
4 ADDRESS BUS 0
5 GROUND
6 CHIP SELECT
7 DATA BUS 0
∫ ∫
8 DATA BUS 1
13 DATA BUS 6
14 DATA BUS 7
15 LCD BACK LIGHT VCC
16 LCD BACK LIGHT CONTROL
DCD-20X
① Door M/C DCD-20X PCB has 4 connectors, which functions are as Tab.4)

Connector Pin No. Signal Function

1 R2CL Close command
2 NUDGE Nudge-close running command
3 SES SES output(48V when normal)
4 DMC DC 48V input
5 SES2 SAFETY SHOE invalidation(when complete CLOSE)

6 EARTH Frame earthing at Control Panel

7
PJ1 8 SS100V S-phase
9 TS100V T-phase
10 R2OP Open command
11 HCL Disabled person running command
12 DERR DOOR ERROR
13 DOLS Complete opening output
14 GND
15 SES1 SAFETY SHOE invalidation(when complete CLOSE)
16
17 RS100V R-phase

Connector Pin No. Signal Function

1 U U-phase of Door motor
2 V V-phase of Door motor
PJ2 3 W W-phase of Door motor
4 TH2 THERMOSTAT input2
5 TH1 THERMOSTAT input1

Connector Pin No. Signal Function

1 SP1 Unused
2 SP2 Unused
PJ3 3 SP3 Unused
4 MON 2/3 Door travel close
5 DLD DOOR LOAD DETECT

Connector Pin No. Signal Function

1 PD1 Diode 1 ANODE
2 PD3 Diode 3 ANODE
3 PD5 Diode 5 ANODE
4 VCC DC+15V
5 VCCR +15V for checking connector not inserted
6 PT3 Transister No.3 EMITTER
7 PT1 Transister No.1 EMITTER
PJ6 8 PD2 Diode No.2 ANODE
9 PT4 Diode No.4 ANODE
10 GND Earth
11
12 PT5 Transister No.5 EMITTER
13 PT4 Transister No.4 EMITTER
14 PT2 Transister No.2 EMITTER