M6.11 M7 07 Elec-Cables - Connectors EWIS

Fundamentals
Licensed Copy to JOCSON College
M6 Materials and Hardware

M7 Maintenance Practices
Issue: 1JAN2008
Author: CeB
M6.11 ELECTRICAL CABLES AND CONNECTORS For Training Purposes Only

LTT 2006
M7.07 EWIS
EASA Part-66
A
P66 M6/M7 WIRES D

Training Manual
For training purposes and internal use only.

Copyright by Lufthansa Technical Training (LTT).
LTT is the owner of all rights to training documents and training
software.
Any use outside the training measures, especially reproduction
and/or copying of training documents and software − also extracts
there of − in any format all (photocopying, using electronic systems
or with the aid of other methods) is prohibited.
Passing on training material and training software to third parties
for the purpose of reproduction and/or copying is prohibited without
the express written consent of LTT.
Copyright endorsements, trademarks or brands may not be
removed.
A tape or video recording of training courses or similar services is
only permissible with the written consent of LTT.
In other respects, legal requirements, especially under copyright
and criminal law, apply.
Lufthansa Technical Training

Dept HAM US
Lufthansa Base Hamburg
Weg beim Jäger 193
22335 Hamburg
Germany
Tel: +49 (0)40 5070 2520

Fax: +49 (0)40 5070 4746
E-Mail: [email protected]
www.Lufthansa-Technical-Training.com
Revision Identification:
The date given in the column ”Issue” on the face of this cover is binding for the complete Training Manual.
Dates and author’s ID, which may be given at the base of the individual pages, are for information about the latest revision of that page(s) only.
The LTT production process ensures that the Training Manual contains a complete set of all necessary pages in the latest finalized revision.
M6 MATERIALS AND HARDWARE
M7 MAINTENANCE PRACTICES
Part-66
ATA 20 ELECTRICAL INSTALLATION

FOR TRAINING PURPOSES ONLY!
FRA US/F-5 CeB Aug 12, 2010 ATA DOC Page 1

Part-66
GENERAL
GENERAL
The installation of on-board electrical systems in an aircraft differs considerably
from the conventional electric installations used in industry and household.
These on-bord electrical systems are comparable with those of automobiles.
Like in automobiles, for weight reasons the metal structure of the cell is used
as a return line which means that most circuits are single core.
In aircraft with wood− or plastic construction, two−core circuits are necessary
due to the lack of conductivity.
The ever increasing use of electric and electronic systems in state−of−the−art
aircraft types also requires an improved knowledge and understanding of the
processing methods and installation techniques.
Thus, the purpose of this book is to provide essential information in the field of
electric installations in aircrafts, which, in combination with the corresponding
documentation and the regulations of the manufacturer, shall enable the reader
to perform professional installations, modifications or repair work.
Generally, electric installations in aircrafts have to be done according to the
manufacturer’s instructions, for example:
Boeing: SWPM (Standard Wiring Practices Manual)
Airbus: ESPM (Electrical Standard Practices Manual)
The corresponding subchapters of this book give reference to respective
chapters of regulations.
FRA US/F-5 CeB Aug 12, 2010 01|M6/M7/L1 Page 2

Part-66
Figure 1 Front Pages of ESPM and SWPM

FRA US/F-5 CeB Aug 12, 2010 01|M6/M7/L1 Page 3
M6.11 ELECTR. CABLES & CONNECTORS
Part-66
M6 ELECTRICAL WIRING AND CABLES

In aircraft construction, a wire is an insulated braid.
Depending on the design, it can be tin−plated, nickel−plated or silver−plated.
The braid consists of several wires twisted together.
Except for certain cases, rigid wires are not used in aircraft construction. A
cable consists of several wires which are combined within another insulation.
Usually, a maximum of three wires combined form one cable of an aircraft; yet
the exception proves the rule. Copper wiring is primarily used due to the overall
best properties (conductivity, elasticity, costs).
Aluminium wiring is only used for reasons of weight reduction in generator
systems and for bulk consumers (e.g. kitchens) and only if the area of
application is not exposed to vibrations.
In the A380, Airbus uses a composite material, which consists of aluminium in
the core and copper on the outside, which is also nickel−plated. The insulation
of the wires is made of plastics such as polyvinyl chloride, nylon, Teflon,
Kapton or Oasis−tape.
Depending on the designated use, the insulation has to be very resistant
against:
all kinds of fluids
mechanical strains
extreme temperature fluctuations.
In accordance to the rules of the aviation authority, wires and cables also have
to be flame resistant and shall not evolve any toxic gases in the case of a fire.
In general, any wire integrated in an aircraft has to comply with a standard that
was approved by the aircraft manufacturer. For example, the American Military
Specification (MIL−W), the German DIN−Norm (LN) or the French NSA
standard.
Figure 2 Wire and Cable
FRA US/F-5 CeB Aug 12, 2010 02|M6/L1 Page 4

Part-66
INSULATION (GREY COLOR)

Arc-Tracking resistant
ALU COPPER
ALLOY CLADDED NICKEL OASIS PTFE tape
tape UV laser markable
Figure 3 A380 Cable

Part-66
M6 SHIELDING
Shielding is the sheathing of wires and cables with an electrically conductive
material in order to prevent electromagnetic fields from either entering or
escaping from wires and cables.
Data buses for instance are shielded in order to avoid alterations in the data
words by inductive coupling.
Shielded single or multi conductor
The wires leading to spark plugs are shielded, for otherwise the high energy
cable with signals below 50 KHz

ignition pulses would lead to malfunctions in various aircraft systems. grounded on one side only!
The shielding of a wire or a cable has to be constantly connected to the
potential of the signal source.
If the cable consists of several parts, the shieldings of these parts have to be
connected.
If both ends of the shieldings would be connected to ground, possibly existing
potential differences could cancel each other out by means of the shieldings
and the flowing current could act magnetically on the signal line and distort the
signal.
Shielded ARINC 429 data bus cable
Thus, the shielding must only be connected to one side.
grounded on both sides!
The exception to this are the ARINC 429 data buses; here it is important that
the devices connected have the same ground potential because the zeros and
ones are defined over specific voltage levels.
For this reason, shieldings in ARINC 429 data buses are connected at both
sides of the system ground.
Figure 4 Shieldings

Part-66
Figure 5 Shielded Wires

Part-66
M6 COAXIAL CABLES
Coaxial cables are used for the transmission of high−frequency signals (e.g.
wires from a radio device to the transmitting antenna). These cables consist of
a center conductor with special insulation, the so−called dielectric, and an outer
conductor, which acts like a shield braid around the dielectric.
There’s an additional insulation around the outer conductor.
Due to the properties in these cables, the outer conductor has to be connected
at both sides of a device because the shield is the return conductor.
Antenna
COAXIAL CABLE
Figure 6 Coax Wire Connection Figure 7 Structure of a Coax Cable

Part-66
Figure 8 Coax Cables

Part-66
M6 WIRES IN FIRE ALARM SYSTEMS

Only wires described as ”fire resistant” according to the construction rules of
the aviation authorities (e.g. EASA Certification Specification CS25.1203) may
PTFE Tape
be used in fire alarm systems. Impregnated Inorganic Fiber
According to the CS−definitions, this requirement is met if the wire can
withstand 1100 Celsius for a total of five minutes without losing their
function.
Furthermore it always comes with a red, white or red−white insulation.
Nickel-Clad Copper Conductor PTFE-Coatet Glass Braid

Figure 9 Type 1 Wire

Part-66
Specifications
ECS EN AWG Rating
Construction
Size Temp.
Ref. Type Ref.
Conductor : 27% Nickel Clad Copper Alloy for AWG 22
ASN 27% Nickel Clad Copper for other AWG
DL 2346003 22 to 16 260 C
E0437 Insulation : Silica Fiber + Fiberglass Braid + PTFE Tape
Application : Fire Resistant Wires

Conductor : 27% Nickel Clad Copper Alloy for AWG 22
27% Nickel Clad Copper for other AWG
ECS 2346005 Insulation :
DW Fire Resistant Insulation + PTFE tape 22 to 14 260 C
0741
Suitable for UV Laser Marking
Application : Fire Proof Wires
ECS 2346005 2 DWA Basic Cores Twisted Cable

DWB 22 to 14 260 C
0741 Application : Fire Proof Wires
ECS 2346005 3 DWA Basic Cores Twisted Cable

DWC 22 to 14 260 C
0741 Application : Fire Proof Wires
1 DWA Basic Core +

Shield : Nickel Plated Copper Braid
ECS 4608004 Sheath :
GPA PTFE Tapes 22 to 14 260 C
0742
2 DWA Basic Core +

GPB PTFE Tapes 22 to 14 260 C
0742
3 DWA Basic Core +
GPC PTFE Tapes 22 to 14 260 C
0742
Figure 10 Fire Resistant Cables

Part-66
M6 THERMOCOUPLE − WIRING
The thermocouple consists of two different metal alloys soldered or welded
together in which a minimal electrical potential is created when the wiring
contact is heated which is proportional to the temperature.
The alloys ALUMEL and CHROMEL are generally used today. These alloys
are also used in the measuring point (formerly the display in the cockpit, today
a digital converter in the engine control unit directly on the engine) in order to
prevent losses (just a few mV) in the voltage created by the heat.
Thus, the terminal lugs and plug contacts at the joints always must consist of
the same alloy as used in the wire. Repair−splices have to be made from the
same alloy as well.
Studs in thermocouple devices generally come in different sizes to avoid
confusion in stud ledges.
In older aircraft models, the cable installation from the engine bulkhead on was
done with COPPER and CONSTANTAN.
This change in material was a method for an improved compensation of the
ambient temperatures.
To prevent a mix−up with the various wires, different insulation colors are
assigned to all the different alloys.
CHROMEL CR o. CH WHITE stud THIN 89% Ni 10% Cr 1% Fe

ALUMEL AL GREEN or RED stud THICK 94% NI 2% Al 1% Si 2,5% Mn 0,5% Fe
COPPER CU RED 100% Cu
CONSTANTAN CN YELLOW 55% CU 44% Ni 1% Mn

Part-66
Figure 11 EGT Connection

Part-66
M6 AROMATIC POLYIMIDE WIRING

The application of aromatic polyimide wires and cables has been common in
civil aircraft construction since the 1960s.
The design of this wire consists of the conductor; thus, two layers of AP foil are
coiled up in opposite directions. The white varnish on the surface of the wire
serves as background for improved legibility of the labeling only.
These wires are popular in aircraft construction because of their low weight
(30−35%) and thinner insulation with improved insulation properties.

However, the ”AP” insulation is not completely unproblematic.
As it turned out, short circuits in wire harnesses in combination with fluids can
lead to a sudden burn off with this kind of insulation, which can result in a
complete failure of the wire harness. This behavior is called CARBON ARC
TRACKING or INSULATION FLASHOVER.
This is caused by the high temperature of the short circuit arc which, in
combination with water, liberates CO−Gas which in turn burns at a very high
temperature.
In order to prevent these problems with ARC− tracking sensitive wires,
processing− and installation errors have to be avoided at all costs.
A high level of cautiousness is necessary when marking, stripping or crimping
any contacts and when AP−wires are installed: the AP−layer must not be
damaged.
The ”piercing” of the wire with test probes is prohibited!
Any damages on the insulation must be repaired immediately.
Further and more specific work instructions must be obtained from the
manufacturer’s documentation and the operator−specific documentation (e.g.
NICKEL PLATED
Lufthansa Technik SPM).
COPPER OUTER COVERING

Varnish or topcoat
POLYIMIDE TAPE ( PTFE or FEP or Liquid H )
WITH 50% OVERLAP
POLYIMIDE TAPE
WITH 50% OVERLAP
Figure 12 AP Wire Structure

Part-66
Figure 13 ARC Tracking in Laboratory Experiment

Part-66
M6 CURRENT CARRYING CAPACITY OF WIRES

The current capacity of wires is directly dependent on the conductor material,
the insulation and the wire size. The way it is installed (in free air or in
harnesses) indirectly also affects the maximum current.
When the maximum current flows, the wire is heated. Releasing this heat into
the surrounding air is much easier with wires in free air than it is with wires in
harnesses.
Figure 14 Capacity in Wire Harnesses

Part-66
CURRENT CARRYING CAPACITY OF COPPER CONDUCTORS (Measured in Amperes)

INSULATION MATERIALS AT GIVEN TEMPERATURES
POLYETHYLENE Kynar
NEOPRENE POLYPROPYLENE POLYVINYLCHLORIDE POLYETHYLENE KAPTON
CONDUCTOR
POLYURETHANE POLYETHYLENE PVC (IRRADIATED) (CROSSLINKED) TEFLON
SIZE
POLYVINYLCHLORIDE (HIGH DENSITY) NYLON Thermoplastic SILICONE
(SEMI−RIGID) AT 90 C AT 105 C Elastomer S AT 200C
AT 80 C AT 125 C
30 AWG 2 3 3 3 4
28 AWG 3 4 4 5 6
26 AWG 4 5 5 6 7
24 AWG 6 7 7 8 10
22 AWG 8 9 10 11 13
20 AWG 10 12 13 14 17
18 AWG 15 17 18 20 24
16 AWG 19 22 24 26 32
14 AWG 27 30 33 40 45
12 AWG 36 40 45 50 55
10 AWG 47 55 58 70 75
8 AWG 65 70 75 90 100
6 AWG 95 100 105 125 135
4 AWG 125 135 145 170 180
2 AWG 170 180 200 225 250
Figure 15 Capacity Depending on Type of Insulation

Part-66
M6 IDENTIFICATION
Only wires complying with the standards of the aeronautical authorities and the
aircraft manufacturer may be installed in aircrafts.
To ensure that this demand is met, the manufacturers of the wires label their
wires with corresponding part numbers.
These part numbers follow the rules for identification by the standards
organisation or the aircraft manufacturer.
The numbers are printed in light or dark green.

Exceptions are red, black or dark green wires: they are labeled with white
numbers.
The aircraft manufacturers furthermore label the wires with a number− and/or
letter code which describes the function of the wire in the aircraft. This is
usually a black imprint.
Figure 16 Printing Colors

Part-66
NSA
BMS
Figure 17 NSA/BMS Standard Identification

M7.07 EWIS
Part-66
WIRING REPAIRS
M7 WIRING DAMAGE CLASSIFICATION AND REPAIR PROCEDURES ACCORDING TO BOEING SWPM 20−10−13
The following pages detail the repair procedures for shielded and unshielded
wires and cables according to SWPM.
The SWPM chapter 20−10−13 contains the following information:
The damage conditions of wire, cable, coax cable, and cable assemblies
The repair conditions for damaged wire, cable, coax cable, and cable
assemblies
The repair procedures for damaged wire, cable, and coax cable.
A distinction is made between:

1. The repair of unshielded wire
2. The repair of shielded wire
GENERAL CONDITIONS FOR WIRE AND CABLE REPAIR
The following conditions apply to all repair procedures:
The cause of damage must be eliminated in order to prevent this damage
from reoccurring.
To keep the wires clean, any repair work must be done with clean hands
and tools.
This could otherwise lead to corrosion on the conductor and worsened
insulation values.
The repair is considered permanent unless stated otherwise in the repair
procedure.
Repair work in a ”fuel vapor area” must be approved for this area.
The following conditions are dependent on the repair area:

Repairs may never be carried out in the protection sleeve
Repairs may never be carried out in a connectors strain relief
Repairs may never be carried out in a bend of the wire
Repairs may never be carried out on parts of the wire/cable which often are
subject to bending, e.g. at an instrument panel or in areas with movable
doors.

M7.07 EWIS
Part-66
THIS PAGE INTENTIONALLY LEFT BLANK


M7.07 EWIS
Part-66
General selection criteria for parts and materials:
Following are the prerequisite conditions for the selection of parts and materials
The temperature class of the insulation materials must be equal or higher
than the temperature class of the wire or cable to be repaired.
The temperature class of the metal parts must be equal or higher than the
temperature class of the conductor to be repaired.
For repairs in ”high temperature areas”, the temperature class of the
material must be class ”D”. (20−02−20)

If part of a wire or cable needs to be replaced, it must be done with wire or
cable with the same part number.
General selection criteria for repair work with a splice
As a general rule, replacement should always be preferred to repair.
The following requirements must be met:
Splices must be insulated
A maximum of three repair splices are permitted in one wire, the ones
mounted during aircraft construction are not relevant.
Whenever more than one splice assembly is necessary during repair, the
separation minimum of the splices is 0.25 inches.
If this requirement can not be met due to the number of splices or
insufficient length of the wire, the splices have to be assembled as shown in
figure 2.

M7.07 EWIS
Part-66
Figure 18 Separation of Splices

M7.07 EWIS
Part-66
M7 STRIPPING OF WIRES
To connect wires and cables in a professional manner, the insulation has to be
separated from the conductor beforehand. This must be carried out with an
approved wire stripper [e.g. Stripmaster] because it prevents damage on the
wire if used properly.
Figure 19 Stripping Tool with Blades
Figure 20 Stripping Tools

M7.07 EWIS
Part-66
Depending on the type of insulation and AWG standard of the wire (Metric or
US), the blades of the stripping tool are exchangeable.
The different AWG standards are clearly detectable by means of green bars
printed on AWG Metric Wires in intervals of approx. 20 cm. The cable clamping
jaws are exchangeable as well.
Figure 21 Content of Jaws Set

Figure 22 Stripping Tools

M7.07 EWIS
Part-66
To strip the wire, it must be placed into the matching notch of the Stripmaster stripping
tool; then the handles must be pressed until stop. When releasing the handles, the
clamping jaws open first so that the wire can be removed smoothly.
Figure 23 Stripping
M7.07 EWIS
Part-66
After the stripping process, inspect the wire for any signs of damage.
Figure 24 Damages caused by Stripping

M7.07 EWIS
Part-66
A cutter or scalpel is used to remove insulation from wires with AWG 10 or

more or the sheath from a shielding.

M7.07 EWIS
Part-66
Figure 25 Cutter/Scalpel
M7.07 EWIS
Part-66
M7 PRESSURE CONNECTIONS
General
To connect a wire to a connecting element, one of the most common methods
today is to crimp these elements onto a wire by means of a special crimping
tool. This procedure is also called ’cold welding’; the connecting element is
non−detachably connected to the wire. Design and requirements have been
defined in order to ensure a proper connection.
The wire strands must be pressed together without it leading to breakage or

separation
The connection may not reduce the electrical attributes of the wire
The junction from the connecting element to a component must be
equivalent to a direct connection to a corresponding copper wire
There also are guidelines regarding tensile strength of crimped connections
To meet these guidelines, specially designed, tested and properly adjusted
crimping tools have to be used for all crimped connections!
Before using a crimping tool, always check:
did you choose the appropriate tool for the terminal?
for cleanliness
for damages
for corrosion
for abrasion

M7.07 EWIS
Part-66
Figure 26 Crimping Tool for PIDG

M7.07 EWIS
Part-66
M7 TERMINALS AND SPLICE

Terminals can be used to connect a single wire to components (switches,
sensors, terminal strips/ terminal blocks, etc.). Splices are used for wire
repairs.
Terminals come in different sizes for various wire sizes but also can have
different shapes, can come with or without insulation and with or without strain
relief.
PIDG
PIDG (Pre Insulated Diamond Grip) terminals and splices are a touch proof
insulated connection, with protection against vibration by means of a
crimped−on strain relief. The terminal is made of electrolytic copper and for
protection against corrosion also is galvanically tin−plated. PIDG terminals and
splices are heat−resistant up to 105C.
Insulation
A PVC − or nylon sleeve is connected to a copper sleeve that also is tightly
connected to the sleeve of the terminal. The copper sleeve ensures a uniform
plastic deformation of the insulating sheath during crimping without affecting
the original insulation thickness.
Crimping
In the crimping procedure both the conductor and the insulation are connected
to the terminal. The insulation sleeve is also identified with dot coding (dot
matrix). These dots indicate whether the terminal has been pressed with the
correct matrix size.
Color Code
To avoid errors when selecting terminals and corresponding crimping tools, the
terminals come with colored insulation sleeves and the crimping tools have
colored handles, too. Different colors are assigned to corresponding wire sizes.
Figure 27 Color Coding

M7.07 EWIS
Part-66
Figure 28 Several Splices

M7.07 EWIS
Part-66
M7 CRIMPING FOR PIDG TERMINALS

After selecting the right crimping tool, the insulation crimp has to be adjusted to
match the wire insulation.
set insulation crimp to position 4, insert terminal, insert non−stripped wire
into the insulation crimping jaws, crimp.
examine whether the wire is held well by the insulation crimp, as a test bend
the wire 90 degrees at the terminal twice.
If this isn’t the case, choose the next smaller position and repeat the
procedure until the desired insulation support is achieved (the smaller the
position/ number, the stronger the crimp of the insulation).
strip wire to desired length
insert terminal into tool until stop and insert the stripped end of the wire. The
strand should stick out approx. 1 mm from the terminal barrel.
Crimp tool until security ratchet is unblocked.
Finally, check if:
− the crimping is on the correct position of the terminal
− all strands have been included
− the imprinted dots are visible
− the insulation crimp is as desired
− the strands are visible at the side with the terminal
Figure 29 Crimping PIDG

M7.07 EWIS
Part-66
Figure 30 Strain Relief Adjustment

M7.07 EWIS
Part-66
M7 BENDING ANGLE FOR TERMINALS

All insulated terminals may be bent if needed for the connection: however, only
once and a maximum of 90degrees on the even side and a maximum of 30
degrees on the side with the wire.

M7.07 EWIS
Part-66
Figure 31 Terminal Bending Angle

M7.07 EWIS
Part-66
M7 COLOR IDENTIFICATION FOR TERMINALS

All terminals AWG 8 or larger have to be identified with a colored heat
shrinkable sleeve.
For three−phase wiring:
Phase A = RED
Phase B = YELLOW
Phase C = BLUE
Single−phase wiring and direct current lines have a YELLOW identification.
Figure 32 Identification of Terminals with Heat Shrinkable Sleeve

M7.07 EWIS
Part-66
Figure 33 Phase Colors

M7.07 EWIS
Part-66
M7 TERMINAL BLOCKS FOR TERMINALS

Terminal blocks help to interconnect several terminals.
It is important to make sure that
the size of the hole at the end of the terminal matches the size of the stud
bolt
a total maximum of 4 terminals are mounted on one bolt
the largest terminal is on the bottom

the rest of the terminals are installed decreasing in size
the top terminal is installed on the right stop side
terminals are installed according to guidelines in the manufacturers
documents (e.g. Boeing)
nuts are tightened with the right torque value
Figure 34 Terminal Block for Terminals

M7.07 EWIS
Part-66
Figure 35 Connection of Terminals

M7.07 EWIS
Part-66
M7 CRIMPING FOR PIDG SPLICES

The same crimping tool as described for terminals is used.
The adjustment process is identical, too. For inserting the splice, see the
illustration (window under the locator).
Insert stripped wire into splice and begin with first crimping procedure. When
finished, check if done properly. Insert other side of the splice into the tool for
the second crimping procedure. Second check as described for terminals.

M7.07 EWIS
Part-66
Figure 36 PIDG Splice Crimping

M7.07 EWIS
Part-66
Possible Crimping Mistakes

Figure 37 Possible Damages in Crimping Procedures

M7.07 EWIS
Part-66
Figure 38 Crimping Damages

M7.07 EWIS
Part-66
M7 CLOSED END SPLICES

Closed end splices are another category of splices: all wires are inserted
stripped and then are electrically connected by crimping with the crimping tool.
Closed end splice must always be arranged so that they stick out of the wire
harness.
The splices should always be arranged as shown in the illustration.
Figure 39 Close End Splice

M7.07 EWIS
Part-66
Figure 40 Closed End Splices

M7.07 EWIS
Part-66
M7 CONNECTION OF WIRES UNDER SPECIAL CIRCUMSTANCES

Under special circumstances, e.g.:
the wire is too thin for the crimp barrel
the diameter of the insulation is too thin for strain relief pressing
more than one wire is to be inserted into the terminal or splice
there are specific aircraft manufacturer regulations how to handle special
cases.
For example Boeing:
Boeing has developed the Circular Area Units (CAU) for cases like these; they
are measurements for the area of crimp barrels and wires.
There is a ”Minimum” and a ”Maximum CAU range” for each crimp sleeve in a
splice or a terminal. As long as the value of the wire is within these values, it
can be crimped without any problems. The CAU−value of wires can be found in
corresponding tables in the SWPM or can be calculated with the following
formula:
2
(1000 StrandDiameter)
CAU + CMA + NumberofStrands
100 100

M7.07 EWIS
Part-66
CAU von Terminals

CAU von Splice

Figure 41 CAU of Wires Figure 42 CAU of Terminals and Splices

Part-66
M6 CONNECTORS
General
Connectors consist of receptacle and plug. They are required for a simple and
safe disconnect of electrical connections during maintenance.
Connectors have pins and sockets which can both (depending on the type of
plug) be housed either in the socket or in the plug.
There is a general rule for determining the socket side: sockets shall always be
installed on the live part of the connector, because the sockets are
scoop−proof and so unwanted short circuits can be prevented.
A distinction is made between circular and rectangular connectors. Rectangular
connectors are preferably used in equipment racks and panels; circular plug
connections can be used in areas with increased environmental influences.

Part-66
Figure 43 Plugs and Receptacles

Part-66
Plug connectors come either with Bayonet− Threaded− or Breech−Coupling.

Bayonet Coupling
By plugging together and a 1/4 turn of the cap nut, the connection is securely
locked; automatic opening is prevented.
Inserting the plug the wrong way is prevented by means of several guide slots
and lugs. They also prevent any confusion when connecting a plug to a
receptacle which is otherwise identical in construction.
Breech Coupling
After positioning, the cap nut is locked with a coaxial movement.
To unlock, the cap nut has to be pulled (Similar to hydraulic or compressed air
connections).
Threaded Coupling
The cap nut is connected to the receptacle by means of a fine thread; this kind
of connector then has to be secured with a lockwire. Exception: plug with
self−locking ”coupling”.
See the following table to determine whether the connection has been done
properly.

Part-66
Figure 44 Various Connectors

Part-66
Because of the various applications for connectors, there are different

shell−sizes and contact arrangements within each individual series of
connectors. The identification for plugs and receptacles varies significantly.
There are versions with
numbers
capital letters
lower case letters
Lower case letters are used if the capital letters are not sufficient due to the
number of contacts; if this still isn’t sufficient, it starts over with double capital
letters.
It is important to remember, that there are no lower case letters for contact
identification in the circuit diagrams for connectors. Therefore lower case
letters are identified with additional characterization as shown below:
*P
−P
<F
A

Part-66
Figure 45 Examples of diff. Shell Sizes and Contact Arrangements

M7.07 EWIS
Part-66
Connectors have to be environmentally sealed in accordance with precise

regulations. In most cases, not all contacts of a connector are used; thus the
empty contact cavities require a seal plug or a seal rod. Therefore there are
corresponding rules for sealing, depending on the grade of environmental
influences for a specific location:
Figure 46 Selecting the Procedure
Figure 47 Plug Seals

M7.07 EWIS
Part-66
Figure 48 Sealing of Contact Cavities

M7.07 EWIS
Part-66
M7 CONNECT AND INSTALL CONNECTORS

There are special crimping tools for connecting a connector to a wire.
At present, three different models are approved by the aircraft
manufacturers.
Figure 49 Crimping Tool MS3191−1

M7.07 EWIS
Part-66
Figure 50 Crimping Tools MS22520/2−01 and MS22520/1−01

M7.07 EWIS
Part-66
Additionally, for very large electrical contacts, there also are

hydraulic or pneumatic crimping tools in various designs.
Figure 51 Hydraulic Crimping Tools

M7.07 EWIS
Part-66
Figure 52 Hydraulic Tool

M7.07 EWIS
Part-66
The crimping tools are subject to a periodic inspection during which they are
checked for sufficient pressure and any signs of wear or damage. Before using
a crimping tool, always make sure that it is not damaged and check the date on
the test badge.
If the crimping tool is not subject to periodic inspections, a check with a GO/NO
GO testing tool is required before each crimping procedure.
Figure 53 Crimping Tool Inspection

M7.07 EWIS
Part-66
Figure 54 Testing of Crimping Tools

M7.07 EWIS
Part-66
All these crimping tools have in common that depending on the contact to be
crimped, the locator, turret or positioner (which determines the position of the
contact in the tool) are exchangeable.
In most models, the depth−stop can also be adjusted to match the
corresponding wire−size.
Figure 55 Crimping Tool Adjustment

M7.07 EWIS
Part-66
Figure 56 Adjusting the Crimping Strength

M7.07 EWIS
Part-66
M7 CONTACT CRIMPING PROCEDURE

Before start, the corresponding locator for the contact has to be selected and
then inserted into the crimping tool. Then the pressure of the tool must be
adjusted according to the size of the wire on the selector knob.
After these preparations, the contact is placed into the tool, the stripped wire
inserted, and then the tool has to be pressed until the security ratchet releases
the opening.
The crimping procedure is finished after an inspection of the contact.

If the contact has no insulation support barrel, the insulation may not touch
the contact.
The insulation has to be inserted into the support barrel if there is one.
The strands must be visible through the inspection hole.
All strands must be located in the contact.
The crimp must be precisely on the correct spot.
Figure 57 Adjusting the Crimping Tool

M7.07 EWIS
Part-66
Figure 58 Contact Crimping Testing

M7.07 EWIS
Part-66
M7 INSERTION AND REMOVAL OF CONTACTS

Contacts are always inserted at the rear by means of a special insertion tool
until they snap into place in the contact cavity.
It is important to insert it straight into the hole to prevent any damages on the
insert.
Figure 59 Insertion of Contacts

M7.07 EWIS
Part-66
Figure 60 Front Release Tools

M7.07 EWIS
Part-66
Figure 61 Insertion of Contacts

M7.07 EWIS
Part-66
Figure 62 Rear Release Tools

M7.07 EWIS
Part-66
For the removal of contacts, a difference is made between connector series

that have contacts to be removed from the front and connector series with
contacts that have to be removed from the rear.
Contact removal from front of connector

When removing the contact from the front of the connector, the tool is inserted
above the contact until the locking clip releases the contact. This activates the
plunger which then pushes the contact out of the cavity.
Removal Tool
Shaft
Wire
Locking Spring released
Figure 63 Contact Removal Form

M7.07 EWIS
Part-66
Figure 64 Front Removal of Contacts

M7.07 EWIS
Part-66
Contact Removal from the Rear End

When removing contacts from the rear, the tool is inserted above the wire and
then into the connector until the locking clip releases the contact. Then,
together with the tool, the wire is removed from the contact cavity.
Figure 65 Rear Removal of Contacts

M7.07 EWIS
Part-66
Figure 66 Front− and Rear Contact Removal

M7.07 EWIS
Part-66
M7 INSTALLATION
Safety instructions
Before carrying out any work on electrical systems on an aircraft, the power
supply must be disconnected in an accident−proof way, and a safeguard must
be provided to prevent unintentional restart.
Ideally, the entire aircraft should be disconnected from the power supply and
the battery should be disconnected.

If this is not possible due to operational circumstances (e.g. several groups
work on the aircraft at the same time) the circuit to be worked on must be
disconnected from the power network.
Pull the circuit breaker
Secure the circuit breaker by using a respective (locking collar)

against reactivation.
Attach the warning tag or sticker to the circuit breaker and the
switch.
Cover open clamps of adjoining systems to avoid accidental

touching.
Implement a voltage test before stating the work.

If possible, a second person should supervise the work.
Figure 67 Warning Sign

M7.07 EWIS
Part-66
Figure 68 Separating Connections

M7.07 EWIS
Part-66
M7 GENERAL GUIDELINES
All work on electrical lines and cables should be carried out according to the
following criteria, in this order:
security of the aircraft during flight time
no time pressure during maintenance and repair work
working cost−efficient

M7.07 EWIS
Part-66


M7.07 EWIS
Part-66
M7 HARNESS SEPARATION
In case of damage on the aircraft, the damage should not affect redundant
systems, which is why harnesses of systems important for the flight should be
separated from each other and should be installed with as few connectors as
possible.
The harnesses are to be installed according to the following specifications:
avoid interference of the different power sources.
occuring errors in the individual systems must not effect other systems
avoid electromagnetic interference (EMI).
To assure this, keep the following points in mind:
separate independent current courses.
separate identical multiple systems.
separate circuits causing EMI and circuits sensitive to EMI.
Circuits which need to be separated are to be installed in different harnesses.
Example: Airbus Segregation Rules
The wires are categorized in six different groups:
Generator G
Power Supply P
Radio/Audio R
Coaxial routes T/U/V
Sensitive wires S
Miscellaneous Wires M
Within these categories, redundant systems are installed on routes 1 or 2,
separated from eachother, e.g.: Airbus A 340.

M7.07 EWIS
Part-66
Figure 69 Separation 1
M7.07 EWIS
Part-66
M7 INSTALLATION OF HARNESSES AND WIRES ON THE

AIRCRAFT
For better−quality installations, wires and cables are tied up to harnesses.
This is done using either cable straps or special cable tie.
Tying off cables with cable straps

Tying off cables with cable straps is a fast method to create harnesses, and is
therefore used by many aircraft manufacturers.

However, the field of application of cable straps is limited:
not with ambient temperatures over 135 deg. C
not for coaxial cables
not inside of harnesses
not outside the pressurized cabin (only permitted for aircraft manufacturers
at the first installation)
not in high vibration areas
not inside the fuel tank
There are different types of cable straps, and they come in different lengths.
They are tightened and cut with a tool approved by the manufacturer.
These cable strap tools can bet set to a tightening torque value which is
suitable for the type of cable strap. This prevents damage on the cable strap
due to a tightening torque which is too high, but also assures that the cable
strap is not too loose on the harness and can slip.
The required tightening torque can be found in the manufacturer’s information
manual.
Figure 70 Panduit Clamp Tool

M7.07 EWIS
Part-66
Figure 71 Assembling of Cable Ties

M7.07 EWIS
Part-66
Tying off cables with cable tie

When tying off cables with cable tie, it has to be assured that only cable tie
appropriate for the application range is used. Also, the temperature range and
potentially occurring fluids have to be considered, when choosing the cable tie.
Generally, two different knots are used for tying up harnesses. Knot 1 is the
standard knot and can be used anywhere, knot 2 is used in areas which are not
easily accessible.
Figure 72 Knot Number
Figure 73 Knot Number 1 Tying Sequence

M7.07 EWIS
Part-66
The following conditions must be met:

The tie may not deform the wires.
The gaps between ties should be between 20 and 25 cm, 5

cm in high vib. areas.
Wires should lie parallel and close to eachother.

No ties under clamps and protective condiuts.
Splice and spare wires must be outside the harness.
Protection against abrasion must be provided for intersections.
No ties are allowed in the tank (with the exception of A340)
Pay particular care with coaxial cables and AP−wires.
Figure 74 Knot Number 2 Tying Sequence

Part-66
M6 INSTALLATION OF HARNESSES INSIDE THE AIRCRAFT

Harnesses and individual wires must be installed on the aircraft in a stable way
and must be protected against abrasion. This can be done using several
components and procedures.
CLAMPS ESPM 20−33−42 SWPM 20−10−12
The components used most often for the installation are clamps, which come in
different types and sizes. There are nylon and metal clamps.
Nylon clamps are used mainly inside the pressurized cabin, and are only used
outside of it if the clamp can withstand the environmental conditions occurring
there. Nylon clamps only come in sizes up to a bore diameter of 1.5 inches.
They have different colors depending on the size.
Figure 75 Clamps 1
Figure 76 Clamps 2

Part-66
Figure 77 List of Nylon Clamp Sizes

M7.07 EWIS
Part-66
To determine the correct size, a special tool is used.

Figure 78 Determining the Clamp Size

M7.07 EWIS
Part-66
Metal clamps are mainly used for hot areas on the aircraft, the choice of clamp depends
on the existing condition of the place of installation.
Figure 79 Metal Clamp Selection

M7.07 EWIS
Part-66
Installation of Clamps
When installing clamps, several rules have to be observed:
Do not pinch wires in the clamp.
The clamp should be closed after tightening the clamping bolt (max.0.8
mm/0.03 inch open).
Clamps should always be installed overhead.
When installing nylon clamps on spacers, washers must be used to avoid
extruding of the clamp.

Clamps may not be installed onto pipes or lines carrying fluids or gases.
Exception: when clamps are not holding the harness but only prevent
abrasion.
The clamp should be installed at right angles tot he harness.
Clamps may not be installed over splices, ties and shielding connections.
If the harness is not big enough to fasten the clamp appropriately, the
diameter can be extended with ”Filler Plugs”, ”Filler Rods” or with suitable
tape.
Harnesses may only be extended with special ”Seal Rings” inside fuel
tanks.
Figure 80 At Right Angles to Wire Harness

M7.07 EWIS
Part-66
Figure 81 Installation of Clamps

M7.07 EWIS
Part-66
Clamps should always be installed overhead.

Figure 82 Installation of Clamps

M7.07 EWIS
Part-66
Figure 83 Adjusting Clamps to Wire Harnesses

M7.07 EWIS
Part-66
Installation of Harnesses
When installing a harness in a clamp, consider that the harness does not have
to be installed fixedly, a potential longitudinal movement as well as a clockwise
and counterclockwise movement is permitted.
Figure 84 Wire Harness Assembly 1

M7.07 EWIS
Part-66
For longitudinal mounting of wire harnesses, they must be clamped to

every frame avoiding any tension.
Figure 85 Wire Harness Assembly 2

M7.07 EWIS
Part-66
A drip−off loop is required before component connections or

plug connectors in order to avoid water penetration.
incorrect
correct
correct correct
Figure 86 Drip−Off Loop

M7.07 EWIS
Part-66
The minimum bending radius must be taken into account during installation for it is crucial
that there are no kinks in wire harnesses.
Minimum bending radii are dependent on wire type and the mounting conditions; please
refer to ESPM 20−33−11 and SWPM 20−10−11 for specific regulations.
Figure 87 Wire Harness Bending Radii

M7.07 EWIS
Part-66
To prevent possible
damages on other airplane
components, the table below
lists the corresponding
minimum clearance in
inches.
Figure 88 Mounting Clearance

M7.07 EWIS
Part-66
Figure 89 Positive Separation

Part-66
M6 PROTECTIVE TUBES
If a contact with other components can not be avoided, the wire harness must
be protected against abrasion by means of an appropriate protective tube.
They are also used to protect the wires against contamination, for example
water, fuel or hydraulic fluid.
A distinction is made between:
rolled protective tubes
metallic protective tubes

protective tubes made of various elastic materials (textiles, elastomers,
rubber)
heat shrinkable sleeves
The appropriate sleeve or tube is chosen based on the environmental
conditions (ESPM 20−33−30).
Important − during the assembly:
no lacing within protective tubes
protective tubes must not be extended; the connection of two protective
tubes is prohibited
all protective tubes longer than 50 mm require a cable with AWG 18 with
insulating caps on both ends and then connected to the protective tube
protective sleeves with a cross section larger than 10 mm require drain
holes on the low points
Figure 90 Protective Tube 1

Part-66
Figure 91 Protective Tube 2

Part-66


Part-66
Convoluted Conduits
SUPERFLEXIT Cutter No. 27672
Figure 92 Convoluted Conduits

Part-66
SHRINKING TUBES
Using of shinking tubes
Acc. ESPM and SWPM shrinking tubes could be used for repair and for
protection of wires and cables.
Shrinking tubes are produced with diameters form 1 mm to 1100 mm.
The possible shinking depends on the material. It’s between 2:1 and 6:1.
For very good sealing some shrinking tubes are inside coated with adhesive.
The producers recommend a ratio of 4:5 between the diameter of the wire or
cable and the shrinking tube to achieve the best result.
The shrinking tube have to be shrinked only with a hot air gun!
The material of the colored shrinking tubes are thermoplastics. These are only
for use in low-temperature-areas.
In high-temperature-areas teflon is used. This tubes needs a very higher
temperatur for shrinking!
WARNING: THE WIRES AND CABLES SHOULD NOT BE HEATED TO
MUCH (LOOK FOR DISCOLOURATIONS)!
WARNING: NO OPEN FLAME ALLOWED FOR SHRINKING!

Part-66
Repair of a wire with a shrinking tube shrinking with an open flame is strictly forbidden
Repair of a shielded wire
Repair Splice
Single Wire
Figure 93 Usages of Shrinking Tubes

Part-66
Spare Wires
Spare wires in wire harnesses are insulated at the wire ends and attached on
the outer part of a wire harness. Depending on the purpose of the wire,
different methods are used for insulation.
Figure 94 Spare Caps

Part-66
Figure 95 End Cap Insulation

Part-66
In contrast to end splices, wires with end caps are usually not stripped.
For special wires there are some exceptions, as shown in the following
illustration.

Part-66
Figure 96 End Cap Insulation

M7.07 EWIS
Part-66
Depending on AWG−size and type, there are different methods for the
attachment of spare wires.
Figure 97 Spare Wires

M7.07 EWIS
Part-66
Figure 98 Attachment of Spare Wires

M7.07 EWIS
Part-66
M7 INSPECTION
SPECIAL INSPECTIONS
General Visual Inspections (GVI) Zonal Inspection
A visual examination of an interior or exterior area, installation, or assembly to A collective term comprising selected General Visual Inspections and visual
detect obvious damage, failure or irregularity. checks that are applied to each zone, defined by access and area, to check
This level of inspection is made from within touching distance unless otherwise system and power plant installations and structure for security and general
specified. A mirror may be necessary to enhance visual access to all exposed condition.
surfaces in the inspection area.
Enhanced Zonal Analysis Procedure (EZAP)
This level of inspection is made under normally available lighting conditions
An analytical logic procedure specifically designed to identify applicable and
such as daylight, hangar lighting, flashlight or droplight and may require
effective tasks that:
removal or opening of access panels or doors.
3. minimize accumulation of combustible materials,
Stands, ladders or platforms may be required to gain proximity to the area
being checked. 4. address wiring discrepancies,
5. address installations where wiring is in close proximity to both primary and
Detailed Inspection (DET) backup flight controls.
An intensive examination of a specific item, installation, or assembly to detect
damage, failure or irregularity. Available lighting is normally supplemented with Common Sense
a direct source of good lighting at an intensity deemed appropriate. „...“Clean and protect as you go
Inspection aids such as mirrors, magnifying lenses or other means may be
References:
necessary.
Airbus: ESPM 20−52−11 Page 1 and on
Common Sense Surface cleaning and elaborate access procedures may be
required. Boeing: SWPM 20−10−06 Page 1 and on
Not the same as DVI!
DET allows tactile examination to determine condition.

M7.07 EWIS
Part-66
M7 GUIDANCE FOR GVI/ZONAL INSPECTION OF EWIS

EWIS DISCREPANCIES DETECTABLE BY GVI/ZONAL INSPECTION
Wiring/Wire Bundles
Wire−to−wire or wire−to−structure contact/chafing
Wire bundle sagging or improperly secured
Wires damaged (obvious damage due to mechanical impact, overheat,
localized chafing, etc.)

Lacing tape and/or ties missing/incorrectly installed
Wiring protection sheath/conduit deformity or incorrectly installed
End of sheath rubbing on end attachment device
Grommet missing or damaged
Dust and lint accumulation
Surface contamination by metal shavings/swarf
Contamination by liquids
Deterioration of previous repairs (e.g., splices)
Deterioration of production splices
Inappropriate repairs (e.g., incorrect splice)
Inappropriate attachments to or separation from fluid lines
Connectors
External corrosion on receptacles
Backshell broken
Rubber pad or packing on backshell missing
No backshell wire securing device

Fool−proofing chain broken
Missing or broken safety wire
Discoloration/evidence of overheat on terminal lugs/blocks
Torque stripe misalignment

M7.07 EWIS
Part-66
M7 DAMAGES
WIRING SYSTEM DAMAGE
Swarf/FOD/Metal Shavings
Wires and cables could be damaged by FODs like washers, srews, screw bits
a.s.o.
The pictures show pulluted wirebundles by drill chips and swarf.
How to clean these wires will be discussed in the module housekeeping.

FODs and drillchips damage the wires when vibrations or movement of the
bundles are present.
Dust and swarf are flame catalysts in case of fire.

M7.07 EWIS
Part-66
Figure 99 Drill Chips and Swarf

M7.07 EWIS
Part-66
EXTERNAL MECHANICALLY INDUCED DAMAGE
Wire bundles have to be separated from moving parts in the aircraft.
This could be done by clamping or protecting the bundle with tapes, sleeves or
tubes.
Chafing wires could cause a short circuit in the electrical systems.

M7.07 EWIS
Part-66
Figure 100 External mechanically induced Damage

M7.07 EWIS
Part-66
HOT GAS
Hot gas areas are:
Engines
Pylons/Struts
APU Compartments
Aircondition Bay
Front Spar and everywhere where bleed ducts are located
In these areas the bundles have to be separeted from the hot air sources.

M7.07 EWIS
Part-66
Figure 101 Hot Gas Damage

M7.07 EWIS
Part-66
FLUID CONTAMINATION
Aggessive fluids could destroy the insulation of wires and cables.
Coductive fluids can cause short circuits in electrical systems.
Here are some examples of fluids you will find in aircraft:
Hydlaulic fluid
Fuel
Motor oil
Corrosion prevention, like Dinol

Water from outside and salt water (aircraft landing on aircraft carriers)
Toilet fluids
Beverages, alcoholic drinks, Coffee, water, even food

M7.07 EWIS
Part-66
Figure 102 Fluid Contamination

M7.07 EWIS
Part-66
VIBRATION/CHAFING
Here are 2 examples:

M7.07 EWIS
Part-66
Figure 103 Vibration/Chafing

M7.07 EWIS
Part-66
CORROSION
Corrosion of wires, cables, grounds, connectors and connections could occur,
when there is a leak of water, acid or leach.

M7.07 EWIS
Part-66
Figure 104 Corrosion

M7.07 EWIS
Part-66
SIGNS OF OVERHEATING
Wires could show a result of overheating in case of a bleed leak or fire in the
aircraft.
The same effect will occur in case of overcurrent or too much heated up wires
when a pig tail was made with a solder sleeve.

M7.07 EWIS
Part-66
Figure 105 Signs of Overheating

M7.07 EWIS
Part-66
WIRE DAMAGES CAUSED BY ANIMALS
Interesting New Failure Mechanism
Following are pictures of damage inflicted on an American Airlines B757.
The Crew had to make an emergency landing after losing all:
TCAS,
ATC Transponder,
DME/VOR functions as well as

VHF communications during the flight.

M7.07 EWIS
Part-66
Figure 106 Wire Damage caused by a Pit Bull

M7.07 EWIS
Part-66
TYPICAL DAMAGE FOUND
Contamination and Damage of connectors
1 Sockets are contaminated by Dinitrol, Socket -F- is not correct

inserted.
2 Back shell is broken.

3 Screw of back shell is missing, no function!
4 Wire bundle is not fixed at strain relief.
5 Wire bundle is not fixed at strain relief.


M7.07 EWIS
Part-66
2.
3.
1.
4.
5.
Figure 107 Connector Damages 1

M7.07 EWIS
Part-66
CONTAMINATION AND DAMAGE OF CONNECTORS (CONT.)
6 Connectors contaminated by Dinitrol
7 Wrong protection used for plugs! Use caps!
8 Connectors contaminated by Dinitrol

9 Do not use paper tape to protect connectors, use caps!


M7.07 EWIS
Part-66
6.
7.
9.
8.
Figure 108 Connector Damages 2
M7.07 EWIS
Part-66
M7 HOUSEKEEPING
AEROPLANE EXTERNAL CONTAMINATION FLUIDS
External contamination sources are:
De-ice fluids
Water and rain
Snow and ice
Miscellaneous (e.g. cargo/beverage spillage)

Air corrosion

M7.07 EWIS
Part-66
Figure 109 External Contamination Sources

M7.07 EWIS
Part-66
AEROPLANE INTERNAL CONTAMINATION SOURCES
Internal contamination sources are:
Hydraulic oils
Engine and APU oils
Fuel
Greases
Galleys and toilets

Lint/Dust
Bleed air and hot areas
Hazardous materials

M7.07 EWIS
Part-66
Figure 110 Internal Contamination Sources

M7.07 EWIS
Part-66
OTHER CONTAMINATION SOURCES
These are for example:
Paint
Corrosion Inhibitor
Drill shavings/Swarf
Foreign Objects (srews, washers, rivets, tools, etc.)

M7.07 EWIS
Part-66
Figure 111 Other Contamination Sources

Part-66
M6 CONTAMINATION PROTECTION PLANNING

It is very important to:
6. Protect yourself
7. Protect the aircraft (e.g plastic foils)
8. Perform the maintenance work
9. Clean the protection first
10.Remove the protection

11.Clean again the adjacent area (clean as you go philosophy)
General Recommendations
An annual cleaning of electrical equipment to remove dust, dirt and grime is
recommended.
To clean areas correctly it is recommended to have a proper lighting.
Cleaning is a very important operation because you can detect a damage in
progress!

Part-66
Figure 112 Contamination Protection Planning

Part-66
M6 CLEANING PROCESS
GENERAL SEQUENCE OF ACTION
1. Identify the contamination source.
2. Stop or contain the source of contamination.
3. After this opereation clean the area. Do not hesitate to clean first a small
area to test the efficiency of the cleaning product.
4. After you cleaning operation check the enviroment. Check the drain holes
of the aircraft as necessary.(e.g. under floor area, cargo belly)
5. When your cleaning operation is fully performed check that you did not
forget a tool used and that there are no foreign objects in the area.
6. Apply clean as you go philosophy.
There are three groups of contamination:
Fluid contamination
Snow and Ice
De-Ice fluid
Cargo spillage
Water and rain
Galleys
Toilets water and waste
Oils and greases
Pressure washing
Solid contamination
Drill shavings/Swarf
Foreign objects (Screws, washers, rivets, tools, etc.)

Enviromental contamination
Lint and dust
Paint
Corrosion inhibitor
Animal waste

Part-66
Figure 113 Cleaning Process

Part-66
M6 BONDINGS
Aircrafts are constructed in such way that lightning strikes and static discharge
can not lead to damages or errors in electrical systems. Therefore all
equipment parts and the structure must be permanently and electrically
conductively connected to one another. This is ensured by means of bondings.
Bondings are required for the following tasks:
protecting crew and passengers against electric shocks in the event of
potential differences
protection of the aircraft and all the installed systems as well as the
occupants against lightning
protection against irregular electrical static charge which could lead to radio
errors as well as discharge sparks
trouble−free current backflow from the consumer to the power source
Different types of copper strands are used for the bondings which are
connected by means of various connection methods (clamps, terminals, etc.).
It is especially important to connect all tubing carrying flammable liquids to the
structure in order to prevent explosions due to static electrical charge.
A new installation of a bonding or of one of its connecting elements requires
the lowest possible contact resistance.
This has to be measured and documented after completion of a connection.
The SWPM and ESPM list the maximum values for respective connections.
Figure 114 Bonding

Part-66
Figure 115 Various Bondings

Part-66
M6 GROUNDINGS
Contrary to bondings, groundings have the purpose to lead the feedback
current into the structure.
It is extremely important to check for any signs of electrochemical corrosion for
currents are permanently flowing through this connection.
A corrosion−preventing installation is crucial.
The risk of penetration of moisture and humidity into groundings must be
prevented by means of appropriate sealing.

Figure 116 Groundings 1 Figure 117 Groundings 2

Part-66
Figure 118 Structure of Groundings

M7.07 EWIS
Part-66
M7 MEASUREMENT OF WIRING AND COMPONENTS

There are different measuring methods for the control of wiring and
components with suitable measuring devices.
Continuity Measurement
Continuity measurement is a method to measure the conductivity of a wire. A
multimeter or ohmmeter is used for this purpose.
A distinction is made between two different techniques:

measuring while the wire is connected to ground

M7.07 EWIS
Part-66
Figure 119 Continuity Measurement

M7.07 EWIS
Part-66
measuring with an extension wire

M7.07 EWIS
Part-66
Figure 120 Measuring with an Extension

M7.07 EWIS
Part-66
Contact Resistance Measurement

The contact resistance measurement is a special case in continuity
measurement for bondings and groundings.
Because of the low resistance to be measured, a special measuring device
with corresponding measurement technique is used for this purpose.
The bonding−meter works with two current− and two voltage power lines − the
so−called ”four wire technology”. A defined current goes through the power
lines and via the connection to be measured; the resistance leads to a voltage
drop which is then measured due to the voltage peaks.
This minimizes measuring errors caused by this measuring arrangement.
Figure 121 Bonding Meter

M7.07 EWIS
Part-66
Figure 122 Contact Resistance Measurement

M7.07 EWIS
Part-66
Insulation Resistance Measurement

Insulation measurements are used to check the quality of insulation.
Similar to a pipe pressure test, an increased pressure, i.e. a voltage that is
higher than the nominal voltage is used. Therefore all devices, motors, sensors
etc. must be disconnected before starting the measurement.
The test can be performed either between two adjacent wires or between the
wire and the structure.
Figure 123 Insulation Tester

M7.07 EWIS
Part-66
Figure 124 Insulation Measurement

M7.07 EWIS
Part-66
Coaxial−Cable−Measurement with Reflectometry Tester

A Time Domain Reflectometry tester (TDR) is used for the detection and
localization of damages in coaxial cables.
This testing device sends a pulse to the cable to be measured, if the pulse hits
a damaged part, a portion of the pulse energy is reflected and returns to the
tester. This reflected pulse is compared to the pulse that was sent out
regarding phase, time variation and amplitude. As a result of this comparison,
the distance of the damage can be located and there are clues regarding the
type of damage.
In order to have an accurate distance measurement, it is necessary to take into
account that the waves in different materials move at different speeds.
The ratio between velocity of propagation and speed of light is called ”cutting
factor” (e.g.: air = 0.99; Teflon = 0.7; polyethylene = 0.66). This is usually
specified by the manufacturer.
The tester basically consists of a pulse generator which is connected to an
oscilloscope.
Figure 125 Reflectometry Tester

M7.07 EWIS
Part-66
Figure 126 Reflectometry Circuit

P66 M6/M7 A E
TABLE OF CONTENTS
ATA 20 ELECTRICAL INSTALLATION . . . . . . . 1 M7 INSTALLATION OF HARNESSES AND WIRES ON
THE AIRCRAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
GENERAL ................................................. 2 M6 INSTALLATION OF HARNESSES INSIDE THE
AIRCRAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
M7 INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
M6 ELECTRICAL WIRING AND CABLES . . . . . . . . . . . . 4
M7 GUIDANCE FOR GVI/ZONAL INSPECTION OF
M6 SHIELDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 EWIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
M6 COAXIAL CABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 M7 DAMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

M6 WIRES IN FIRE ALARM SYSTEMS . . . . . . . . . . . . . . 10 M7 HOUSEKEEPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
M6 THERMOCOUPLE − WIRING . . . . . . . . . . . . . . . . . . . 12 M6 CONTAMINATION PROTECTION PLANNING . . . . 140
M6 AROMATIC POLYIMIDE WIRING . . . . . . . . . . . . . . . . 14 M6 CLEANING PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . 142
M6 CURRENT CARRYING CAPACITY OF WIRES . . . . 16 M6 BONDINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
M6 IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 M6 GROUNDINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
WIRING REPAIRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 M7 MEASUREMENT OF WIRING AND COMPONENTS 148
M7 WIRING DAMAGE CLASSIFICATION AND
REPAIR PROCEDURES ACCORDING TO BOEING
SWPM 20−10−13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
M7 STRIPPING OF WIRES . . . . . . . . . . . . . . . . . . . . . . . . 24
M7 PRESSURE CONNECTIONS . . . . . . . . . . . . . . . . . . . 30
M7 TERMINALS AND SPLICE . . . . . . . . . . . . . . . . . . . . . . 32
M7 CRIMPING FOR PIDG TERMINALS . . . . . . . . . . . . . 34
M7 BENDING ANGLE FOR TERMINALS . . . . . . . . . . . . 36
M7 COLOR IDENTIFICATION FOR TERMINALS . . . . . 38
M7 TERMINAL BLOCKS FOR TERMINALS . . . . . . . . . . 40
M7 CRIMPING FOR PIDG SPLICES . . . . . . . . . . . . . . . . 42
M7 CLOSED END SPLICES . . . . . . . . . . . . . . . . . . . . . . . 46
M7 CONNECTION OF WIRES UNDER
SPECIAL CIRCUMSTANCES . . . . . . . . . . . . . . . . . . . . . . . 48
M6 CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
M7 CONNECT AND INSTALL CONNECTORS . . . . . . . . 58
M7 CONTACT CRIMPING PROCEDURE . . . . . . . . . . . . 66
M7 INSERTION AND REMOVAL OF CONTACTS . . . . . 68
M7 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
M7 GENERAL GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . 78
M7 HARNESS SEPARATION . . . . . . . . . . . . . . . . . . . . . . . 80
Page i
P66 M6/M7 A E
TABLE OF CONTENTS
Page ii
P66 M6/M7 A E
TABLE OF FIGURES
Figure 1 Front Pages of ESPM and SWPM . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 36 PIDG Splice Crimping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 2 Wire and Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 37 Possible Damages in Crimping Procedures . . . . . . . . . . . . . . 44
Figure 3 A380 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 38 Crimping Damages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 4 Shieldings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 39 Close End Splice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 5 Shielded Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 40 Closed End Splices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 6 Coax Wire Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 41 CAU of Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 7 Structure of a Coax Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 42 CAU of Terminals and Splices . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 8 Coax Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 43 Plugs and Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 9 Type 1 Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 44 Various Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 10 Fire Resistant Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 45 Examples of diff. Shell Sizes and Contact Arrangements . . . 55
Figure 11 EGT Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 46 Selecting the Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 12 AP Wire Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 47 Plug Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 13 ARC Tracking in Laboratory Experiment . . . . . . . . . . . . . . . . . 15 Figure 48 Sealing of Contact Cavities . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 14 Capacity in Wire Harnesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 49 Crimping Tool MS3191−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 15 Capacity Depending on Type of Insulation . . . . . . . . . . . . . . . 17 Figure 50 Crimping Tools MS22520/2−01 and MS22520/1−01 . . . . . . . 59
Figure 16 Printing Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 51 Hydraulic Crimping Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 17 NSA/BMS Standard Identification . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 52 Hydraulic Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 18 Separation of Splices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 53 Crimping Tool Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 19 Stripping Tool with Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 54 Testing of Crimping Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 20 Stripping Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 55 Crimping Tool Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 21 Content of Jaws Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 56 Adjusting the Crimping Strength . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure 22 Stripping Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 57 Adjusting the Crimping Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Figure 23 Stripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 58 Contact Crimping Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 24 Damages caused by Stripping . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 59 Insertion of Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 25 Cutter/Scalpel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Figure 60 Front Release Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Figure 26 Crimping Tool for PIDG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Figure 61 Insertion of Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 27 Color Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Figure 62 Rear Release Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 28 Several Splices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Figure 63 Contact Removal Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 29 Crimping PIDG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 64 Front Removal of Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 30 Strain Relief Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure 65 Rear Removal of Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Figure 31 Terminal Bending Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure 66 Front− and Rear Contact Removal . . . . . . . . . . . . . . . . . . . . . . 75
Figure 32 Identification of Terminals with Heat Shrinkable Sleeve . . . . 38 Figure 67 Warning Sign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 33 Phase Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 68 Separating Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 34 Terminal Block for Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Figure 69 Separation 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 35 Connection of Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 70 Panduit Clamp Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Page i
P66 M6/M7 A E
TABLE OF FIGURES
Figure 71 Assembling of Cable Ties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Figure 106 Wire Damage caused by a Pit Bull . . . . . . . . . . . . . . . . . . . . . 129
Figure 72 Knot Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Figure 107 Connector Damages 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Figure 73 Knot Number 1 Tying Sequence . . . . . . . . . . . . . . . . . . . . . . . . 84 Figure 108 Connector Damages 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Figure 74 Knot Number 2 Tying Sequence . . . . . . . . . . . . . . . . . . . . . . . . 85 Figure 109 External Contamination Sources . . . . . . . . . . . . . . . . . . . . . . . 135
Figure 75 Clamps 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Figure 110 Internal Contamination Sources . . . . . . . . . . . . . . . . . . . . . . . 137
Figure 76 Clamps 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Figure 111 Other Contamination Sources . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 77 List of Nylon Clamp Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Figure 112 Contamination Protection Planning . . . . . . . . . . . . . . . . . . . . . 141
Figure 78 Determining the Clamp Size . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Figure 113 Cleaning Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Figure 79 Metal Clamp Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Figure 114 Bonding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Figure 80 At Right Angles to Wire Harness . . . . . . . . . . . . . . . . . . . . . . . . 90 Figure 115 Various Bondings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Figure 81 Installation of Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Figure 116 Groundings 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Figure 82 Installation of Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Figure 117 Groundings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Figure 83 Adjusting Clamps to Wire Harnesses . . . . . . . . . . . . . . . . . . . . 93 Figure 118 Structure of Groundings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Figure 84 Wire Harness Assembly 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Figure 119 Continuity Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Figure 85 Wire Harness Assembly 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Figure 120 Measuring with an Extension . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Figure 86 Drip−Off Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Figure 121 Bonding Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Figure 87 Wire Harness Bending Radii . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Figure 122 Contact Resistance Measurement . . . . . . . . . . . . . . . . . . . . . 153
Figure 88 Mounting Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Figure 123 Insulation Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Figure 89 Positive Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Figure 124 Insulation Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Figure 90 Protective Tube 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Figure 125 Reflectometry Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Figure 91 Protective Tube 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Figure 126 Reflectometry Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Figure 92 Convoluted Conduits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 93 Usages of Shrinking Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 94 Spare Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Figure 95 End Cap Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 96 End Cap Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 97 Spare Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Figure 98 Attachment of Spare Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Figure 99 Drill Chips and Swarf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Figure 100 External mechanically induced Damage . . . . . . . . . . . . . . . . 117
Figure 101 Hot Gas Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Figure 102 Fluid Contamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Figure 103 Vibration/Chafing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Figure 104 Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 105 Signs of Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Page ii
P66 M6/M7 A E
TABLE OF FIGURES
Page iii
P66 M6/M7 A E
TABLE OF FIGURES
Page iv

M6.11 M7 07 Elec-Cables - Connectors EWIS

Uploaded by

Copyright:

Available Formats

M6.11 M7 07 Elec-Cables - Connectors EWIS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

M6.11 M7 07 Elec-Cables - Connectors EWIS

Uploaded by

Copyright:

Available Formats

What are some of the main topics covered in the document?

What are some of the main topics covered in the document?

What are some of the key considerations for electrical wiring installation mentioned?

What are some of the key considerations for electrical wiring installation mentioned?

Fundamentals

Licensed Copy to JOCSON College

M6 Materials and Hardware

M6.11 ELECTRICAL CABLES AND CONNECTORS For Training Purposes Only

P66 M6/M7 WIRES D

For training purposes and internal use only.

Lufthansa Technical Training

Tel: +49 (0)40 5070 2520

ATA 20 ELECTRICAL INSTALLATION

FRA US/F-5 CeB Aug 12, 2010 ATA DOC Page 1

FRA US/F-5 CeB Aug 12, 2010 01|M6/M7/L1 Page 2

Figure 1 Front Pages of ESPM and SWPM

M6 ELECTRICAL WIRING AND CABLES

Figure 2 Wire and Cable

FRA US/F-5 CeB Aug 12, 2010 02|M6/L1 Page 4

INSULATION (GREY COLOR)

Figure 3 A380 Cable

cable with signals below 50 KHz

FRA US/F-5 CeB Aug 12, 2010 03|M6/L1 Page 6

Figure 5 Shielded Wires

at both sides of a device because the shield is the return conductor.

Figure 6 Coax Wire Connection Figure 7 Structure of a Coax Cable

FRA US/F-5 CeB Aug 12, 2010 03|M6/L1 Page 8

Figure 8 Coax Cables

M6 WIRES IN FIRE ALARM SYSTEMS

Furthermore it always comes with a red, white or red−white insulation.

Nickel-Clad Copper Conductor PTFE-Coatet Glass Braid

Figure 9 Type 1 Wire

FRA US/F-5 CeB Aug 12, 2010 04|M6/L1 Page 10

Application : Fire Resistant Wires

ECS 2346005 2 DWA Basic Cores Twisted Cable

ECS 2346005 3 DWA Basic Cores Twisted Cable

1 DWA Basic Core +

2 DWA Basic Core +

Figure 10 Fire Resistant Cables

CHROMEL CR o. CH WHITE stud THIN 89% Ni 10% Cr 1% Fe

FRA US/F-5 CeB Aug 12, 2010 05|M6/L1 Page 12

Figure 11 EGT Connection

M6 AROMATIC POLYIMIDE WIRING

(30−35%) and thinner insulation with improved insulation properties.

COPPER OUTER COVERING

Figure 12 AP Wire Structure

FRA US/F-5 CeB Aug 12, 2010 06|M6/L1 Page 14

Figure 13 ARC Tracking in Laboratory Experiment

M6 CURRENT CARRYING CAPACITY OF WIRES

Figure 14 Capacity in Wire Harnesses

FRA US/F-5 CeB Aug 12, 2010 07|M6/L1 Page 16

CURRENT CARRYING CAPACITY OF COPPER CONDUCTORS (Measured in Amperes)

Figure 15 Capacity Depending on Type of Insulation

The numbers are printed in light or dark green.

Figure 16 Printing Colors

Figure 17 NSA/BMS Standard Identification

A distinction is made between:

The following conditions are dependent on the repair area:

FRA US/F-5 CeB Aug 12, 2010 12|M7/L1 Page 20