Symbol ls4000 Programmers Guide

LS 4000 and
LS 400Xi Series
Advanced Programmer’s Guide

LS 4000 and LS 400Xi Series Advanced Programmer’s Guide
70-35834-01
Revision B — February 2001
2 Symbol Technologies, Inc. One Symbol Plaza, Holtsville N.Y. 11742-1300

LS 4000 and 400Xi Series
Advanced Programmer’s Guide
70-35834-01
Revision B
February 2001
 1998 - 2001 by Symbol Technologies, Inc. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or
mechanical means, without permission in writing from Symbol. This includes electronic or
mechanical means, such as photocopying, recording, or information storage and retrieval
systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware,
furnished to the user is on a licensed basis. Symbol grants to the user a non-transferable and
non-exclusive license to use each software or firmware program delivered hereunder (licensed
program). Except as noted below, such license may not be assigned, sublicensed, or otherwise
transferred by the user without prior written consent of Symbol. No right to copy a licensed
program in whole or in part is granted, except as permitted under copyright law. The user
shall not modify, merge, or incorporate any form or portion of a licensed program with other
program material, create a derivative work from a licensed program, or use a licensed
program in a network without written permission from Symbol. The user agrees to maintain
Symbol’s copyright notice on the licensed programs delivered hereunder, and to include the
same on any authorized copies it makes, in whole or in part. The user agrees not to
decompile, disassemble, decode, or reverse engineer any licensed program delivered to the
user or any portion thereof.
Symbol reserves the right to make changes to any software or product to improve reliability,
function, or design.
Symbol does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any

Symbol Technologies, Inc., intellectual property rights. An implied license only exists for
equipment, circuits, and subsystems contained in Symbol products.
Symbol, Spectrum One, and Spectrum24 are registered trademarks of Symbol Technologies,
Inc. Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, New York 11742-1300
http://www.symbol.com
iv
Contents
About This Manual

Notational Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Symbol Support Center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Chapter 1. Advanced Data Formatting

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Rules: Criteria Linked to Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Using ADF Bar Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Special Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Begin New Rule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Save Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Quit Entering Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Disable Rule Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 1-3
Code Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Code Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Message Containing A Specific Data String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Specific String at Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Specific String, Any Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Any Message OK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Rule Belongs To Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 1-4
Send Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Setup Field(s). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Modify Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Pad Data With Spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Pad Data With Zeros. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
i
LS 4000 and LS 400Xi Advanced Programmer’s Guide
Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Send Keystroke (Control Characters and Keyboard Characters). . . . . . . . . . . . . . . . . . . . . . . . 1-6
Turn On/Off Rule Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
ADF Bar Code Menu Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Rule 1: The Code 128 Scanning Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Rule 2: The UPC Scanning Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Alternate Rule Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Rules Hierarchy (in Bar Codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Default Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Beeper Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Chapter 2. ADF Bar Codes

Special Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Begin New Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Save Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Quit Entering Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Disable Rule Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 2-4
Code Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Code Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Specific Data String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Rule Belongs To Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . 2-13
Send Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Setup Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Send Preset Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Modify Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Pad Data with Spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Pad Data with Zeros. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Control Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Keyboard Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Send ALT Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Send Command Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52
Send Special Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54
Send Keypad Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55
Send Function Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59
Turn On/Off Rule Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65
Alphanumeric Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66
ii
Contents
Appendix A. ASCII Tables and Keyboard Layouts

ASCII Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Keyboard Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
iii
LS 4000 and LS 400Xi Advanced Programmer’s Guide
iv
About This Manual
The LS 4000 and LS 400Xi Advanced Programmers Guide provides programming

information and bar codes for the LS 4000 and LS 400Xi series scanners.
Notational Conventions
The following conventions are used in this document:
! LS 4000 refers to the LS 4000 series of scanners

! LS 400Xi refers to both the LS 4004i and the LS 4005i, unless specifically noted
! Bullets (•) indicate:
" action items
" lists of alternatives
" lists of required steps that are not necessarily sequential.
! Sequential lists (e.g., those that describe step-by-step procedures) appear as
numbered lists
! References to other sections, chapters, or manuals appear in italics.
Related Publications
! LS 400Xi Product Reference Guide, p/n 70-37898-xx
! LS 400Xi Quick Reference Guide, p/n 70-33849-xx
! LS 4000 Series Product Reference Guide, p/n 70-16171-xx
! LS 4000 Series Quick Reference Guide, p/n 70-16423-xx.
v
Service Information
If you have a problem with your equipment, contact the Symbol Support Center for your
region. See below for contact information. Before calling, have the model number, serial
number, and several of your bar code symbols at hand.
Call the Support Center from a phone near the scanning equipment so that the service person
can try to talk you through your problem. If the equipment is found to be working properly
and the problem is symbol readability, the Support Center will request samples of your bar
codes for analysis at our plant.
If your problem cannot be solved over the phone, you may need to return your equipment for
servicing. If that is necessary, you will be given specific directions.
Note: Symbol Technologies is not responsible for any damages incurred

during shipment if the approved shipping container is not used.
Shipping the units improperly can possibly void the warranty. If the
original shipping container was not kept, contact Symbol to have
another sent to you.
Symbol Support Center

In the U.S.A., for service information, warranty information or technical assistance, call:
SYMBOL SUPPORT Europe/Mid-East Distributor Operations

CENTER Contact your local distributor or call
1-800-653-5350 +44 118 945 7360
Canada Asia
Mississauga, Ontario Singapore
Canadian Headquarters Symbol Technologies Asia, Inc.
(905) 629-7226 337-6588 (Inside Singapore)
+65-337-6588 (Outside Singapore)
If you purchased your Symbol product from a Symbol Business Partner, contact that Business
Partner for service.
vi
About This Manual
Warranty
Symbol Technologies, Inc (“Symbol”) manufactures its hardware products in accordance with industry-
standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment,
products will be free from defects in materials and workmanship.
This warranty is provided to the original owner only and is not transferable to any third party. It shall
not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii)
which has not been maintained in accordance with any operating or handling instructions supplied by
Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse, abuse, power
shortage, negligence or accident or (iv) which has been used other than in accordance with the product
operating and handling instructions. Preventive maintenance is the responsibility of customer and is not
covered under this warranty.
Wear items and accessories having a Symbol serial number, will carry a 90-day limited warranty. Non-
serialized items will carry a 30-day limited warranty.
Warranty Coverage and Procedure

During the warranty period, Symbol will repair or replace defective products returned to Symbol’s
manufacturing plant in the US. For warranty service in North America, call the Symbol Support Center
at 1-800-653-5350. International customers should contact the local Symbol office or support center.
If warranty service is required, Symbol will issue a Return Material Authorization Number. Products
must be shipped in the original or comparable packaging, shipping and insurance charges prepaid.
Symbol will ship the repaired or replacement product freight and insurance prepaid in North America.
Shipments from the US or other locations will be made F.O.B. Symbol’s manufacturing plant.
Symbol will use new or refurbished parts at its discretion and will own all parts removed from repaired
products. Customer will pay for the replacement product in case it does not return the replaced product
to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s
charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange.
Customer accepts full responsibility for its software and data including the appropriate backup thereof.
Repair or replacement of a product during warranty will not extend the original warranty term.
Symbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or phone
support, that can be implemented to meet customer’s special operational requirements and are available
at a substantial discount during warranty period.
General
Except for the warranties stated above, Symbol disclaims all warranties, express or implied, on products
furnished hereunder, including without limitation implied warranties of merchantability and fitness for
a particular purpose. The stated express warranties are in lieu of all obligations or liabilities on part of
Symbol for damages, including without limitation, special, indirect, or consequential damages arising
out of or in connection with the use or performance of the product.
vii
Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way
exceed the purchase price of said product, except in instances of injury to persons or property.
Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential
damages, so the proceeding exclusion or limitation may not apply to you.
viii
Chapter 1
Advanced Data Formatting
Introduction
Advanced Data Formatting (ADF) is a means of customizing data before transmission to your
host device. Scan data can be edited to suit your particular requirements.
ADF can be implemented through scanning a related series of bar codes, which appear in
Chapter 2, ADF Bar Codes.
Rules: Criteria Linked to Actions

In ADF, data is customized through rules. These rules perform detailed actions when the data
meets certain criteria. One rule may consist of single or multiple criteria applied to single or
multiple actions.
For instance, a data formatting rule could be the following:
Criteria: When scan data is Code 39, length 12, and data at the start position is
the string “129”,
Actions: pad all sends with zeros to length 8,
send all data up to X,
send a space.
If a Code 39 bar code of 1299X1559828 is scanned, the following is transmitted:
00001299<space>. If a Code 39 bar code of 1299X15598 is scanned, this rule is ignored.
The rule specifies the editing conditions and requirements before data transmission occurs.
1-1
Using ADF Bar Codes

When you program a rule, make sure the rule is logically correct. Plan ahead before you start
scanning.
To program each data formatting rule:
! Start the Rule. Scan the BEGIN NEW RULE bar code on page 2-1.
! Criteria. Scan the bar codes for all pertinent criteria. Criteria can include code type
(e.g., Code 128), code length, or data that contains a specific character string (e.g.,
the digits “129”). These options are described in Criteria on page 1-3.
! Actions. Scan all actions related to, or affecting, these criteria. The actions of a rule
specify how to format the data for transmission. These options are described in
Actions on page 1-4.
! Save the Rule. Scan the SAVE RULE bar code on page 2-1. This places the rule in the
“top” position in the rule buffer.
! If you make errors during this process, some special-purpose bar codes may be
useful: Erase Criteria and Start Again, Erase Actions and Start Again, Erase
Previously Saved Rule, etc.
Criteria, actions, and entire rules may be erased by scanning the appropriate bar code (see
page 2-2).
Beeper Definitions on page 1-11 help guide you through the programming steps.
Special Commands
Begin New Rule

Scan this bar code first when programming a data formatting rule.
Save Rule
Scan this bar code to complete a data formatting rule.
Erase
Use these bar codes to erase criteria, actions, and rules.
1-2
Quit Entering Rules

Scan this bar code to quit entering rules.
Disable Rule Set

These bar codes allow you to disable particular rule sets.
Criteria
Code Types
Select any number of code types to be affected. All selected codes must be scanned in
succession, prior to selecting other criteria. If you don't select a code type, all code types will
be affected.
Code Lengths
Define the number of characters the selected code type must contain. If you don't select a
code length, selected code types of any length will be affected.
Message Containing A Specific Data String

Select whether the formatting affects data that begins with a specific character or data string,
or contains a specific character or data string.
Specific String at Start

Scan this bar code, then scan the bar codes representing the desired character or characters
(up to a total of 8) in the Alphanumeric Keyboard on page 2-66.
Specific String, Any Location

Scan this bar code, then, using the Numeric Keypad on page 2-11, scan a two-digit number
representing the position (use a leading “zero” if necessary). Then scan the desired character
or characters (up to a total of 8) on the Alphanumeric Keyboard on page 2-66, followed by
the END OF MESSAGE bar code on page 2-72.
Any Message OK
By not scanning any bar code, all selected code types are formatted, regardless of information
contained.
1-3
Rule Belongs To Set

Select the set a rule belongs to.
Actions
Select how to format the data for transmission.
Send Data
Send all data that remains, send all data up to a specific character selected from the
Alphanumeric Keyboard, or send the next N characters. N = any number from 1 to 254,
selected from the Alphanumeric Keyboard.
Setup Field(s)
Define fields as follows:
Move Cursor To a Character

Scan the MOVE CURSOR TO CHARACTER bar code on page 2-16, then any printable
ASCII character from the Alphanumeric Keyboard. When this is used, the cursor moves to
the position after the matching character. If the character is not there, the rule fails and ADF
tries the next rule.
Move Cursor to Start of Data

Scan this bar code to move cursor to the beginning of the data.
Move Cursor Past a Character

This parameter moves the cursor past all sequential occurrences of a selected character. Scan
the MOVE CURSOR PAST CHARACTER bar code on page 2-16, then select a character
from the Alphanumeric Keyboard. If the character is not there, the cursor does not move (i.e.,
has no effect).
Skip Ahead “N” Characters

Scan one of these bar codes to select the number of positions ahead you wish to move the
cursor.
1-4
Skip Back “N” Characters

Scan one of these bar codes to select the number of positions back you wish to move the
cursor.
Send Preset Value

Send Values 1 through 6 by scanning the appropriate bar code. These values must be set using
the prefix/suffix values in Table A-1 on page A-2.
Value 1 = Scan Suffix

Value 2 = Scan Prefix
Modify Data
Modify data in the ways listed. The following actions work for all send commands that
follow it within a rule. If you program pad zeros to length 6, send next 3 characters, stop
padding, send next 5 characters, three zeros are added to the first send, and the next send is
unaffected by the padding. These options do not apply to the Send Keystroke or Send Preset
Value options.
Remove All Spaces

To remove all spaces in the send commands that follow, scan this bar code.
Crunch All Spaces

To leave one space between words, scan this bar code. This also removes all leading and
trailing spaces.
Stop Space Removal

Scan this bar code to disable space removal.
Remove Leading Zeros

Scan this bar code to remove all leading zeros.
Stop Zero Removal

Scan this bar code to disable the removal of zeros.
1-5
Pad Data With Spaces

To pad data to the left, scan the bar code containing the desired number of spaces. This
parameter is activated by Send commands.
Pad Data With Zeros

To pad data to the left, scan the bar code containing the desired number of zeros. This
parameter is activated by Send commands.
Beeps
Select a beep sequence for each ADF rule.
Send Keystroke (Control Characters and Keyboard Characters)

Scan the “Send __” bar code for the keystroke you wish to send.
Turn On/Off Rule Sets

Use these bar codes to turn rule sets on and off.
ADF Bar Code Menu Example

This section provides an example of how ADF rules are entered and used for scan data.
An auto parts distribution center wants to encode manufacturer ID, part number, and
destination code into their own Code 128 bar codes. The distribution center also has
products that carry UPC bar codes, placed there by the manufacturer. The Code 128 bar
codes have the following format:
MMMMMPPPPPDD
Where: M = Manufacturer ID
P = Part Number
D = Destination Code
The distribution center uses a PC with dedicated control characters for manufacturer ID
<CTRL M>, part number <CTRL P>, and destination code <CTRL D>. At this center the
UPC data is treated as manufacturer ID code.
1-6
The following rules need to be entered:
When scanning data of code type Code 128, send the next 5 characters, send the
manufacturer ID key <CTRL M>, send the next 5 characters, send the part number key
<CTRL P>, send the next 2 characters, send the destination code key <CTRL D>.
When scanning data of code type UPC/EAN, send all data, send the manufacturer ID key
<CTRL M>.
To enter these rules, follow the steps below:
Rule 1: The Code 128 Scanning Rule

Step Bar Code On Page Beep Indication
1 Begin New Rule 2-1 High High
2 Code 128 2-4 High High
3 Send next 5 characters 2-13 High High
4 Send <CTRL M> 2-33 High High
6 Send <CTRL P> 2-34 High High
8 Send <CTRL D> 2-32 High High
9 Save Rule 2-1 High Low High Low
Rule 2: The UPC Scanning Rule

Step Bar Code On Page Beep Indication
1 Begin New Rule 2-1 High High
2 UPC/EAN 2-4 High High
3 Send all remaining data 2-13 High High
4 Send <CTRL M> 2-33 High High
5 Save Rule 2-1 High Low High Low
If you made any mistakes while entering this rule, scan the QUIT ENTERING RULES bar
code on page 2-2. If you already saved the rule, scan the ERASE PREVIOUSLY SAVED RULE
bar code on page 2-2.
1-7
Alternate Rule Sets

ADF rules may be grouped into one of four alternate sets which can be turned on and off
when needed. This is useful when you want to format the same message in different ways.
For example, a Code 128 bar code contains the following information:
Class (2 digits), Stock Number (8) digits, Price (5 digits)

This bar code might look like this:
245671243701500
where:
Class = 24
Stock Number = 56712437
Price = 01500
Ordinarily you would send this data as follows:
24 (class key)
56712437 (stock key)
01500 (enter key)
But, when there is a sale, you may want to send only the following:
24 (class key)
56712437 (stock key)
and the cashier will key the price manually.
To implement this, you would first enter an ADF rule that applies to the normal situation.
This rule may look like this:
When scanning a bar code of length 15, send the next 2 characters, send the class key,
send the next 8 characters, send the stock key, send the data that remains, send the Enter
key.
The “sale” rule may look like this:
send the next 8 characters, send the stock key.
To switch between the two sets of rules, a “switching rule” must be programmed. This rule
specifies what type of bar code must be scanned to switch between the rule sets. For example,
1-8
in the case of the “sale” rule above, the rule programmer wants the cashier to scan the bar
code “M” before a sale. To do this, a rule can be entered as follows:
When scanning a bar code of length 1 that begins with “M”, select rule set number 1.
Another rule could be programmed to switch back.
When scanning a bar code of length 1 that begins with “N”, turn off rule set number 1.
The switching back to normal rules can also be done in the “sale” rule. For example, the rule
may look like this:
send the next 8 characters, send the stock key, turn off rule set 1.
It is recommended that you scan the DISABLE ALL RULE SETS bar code on page 2-3 after
programming a rule belonging to an alternate rule set.
In addition to enabling and disabling rule sets within the rules, you can enable or disable them
by scanning the appropriate bar codes on 2-3.
Rules Hierarchy (in Bar Codes)

The order of programming individual rules is important.The most general rule should be
programmed last.
All programmed rules are stored in a buffer. As they are programmed, they are stored at the
“top” of a rules list. If three rules have been created, the list would be configured as follows:
Third Rule
Second Rule
First Rule
When data is scanned, the rules list is checked from top to bottom to determine if the criteria
matches (and therefore, if the actions should occur). Input is modified into the data format
specified by the first matching set of criteria it finds. Be sure that your most general rule is the
last one programmed.
For example, if the THIRD rule states:
When scanning a bar code of any length, send all data, then send the ENTER key.
And the SECOND rule states:
When scanning a Code 128 bar code of length 12, send the first four characters, then
send the ENTER key, then send all remaining data.
1-9
If a Code 128 bar code of length 12 were scanned, the THIRD rule would be in effect. The
SECOND rule would appear to not function.
Note also that ADF rules are actually created when you use the standard data editing
functions. Scan options are entered as ADF rules, and the hierarchy mentioned above also
applies to them. For the LS 4800, this applies to prefix/suffix programming in the parameter
Scan Data Transmission Format.
These rules reside in the same “rule list” as ADF Rules, so the order of their creation is also
important.
Default Rules
Every unit has a default rule to send all scan data. Units with custom software may have one
or more default rules burned in. The rules hierarchy checks user programmable rules first,
then the default rules. Default rules can be disabled by entering the following general rule in
the user programmable buffer:
When receiving scan data, send all data.

Since this rule always applies, ADF will never go into the default rules.
1-10
Beeper Definitions
The following table defines beep sequences which occur during data entry.
Table 1-1. Beeper Definitions
Normal Data Entry. Duration of tones are short.
Beeper Sequence Indication
High-Low Entry of a number is expected. Enter another digit. Add
leading zeros to the front if necessary.
Low-Low Entry of an alphabetic character is expected. Enter another
character or scan the End of Message bar code.
High-High Entry of Criterion/Action is expected. Enter another
criterion or action, or scan the Save Rule bar code.
High-Low-High-Low Rule saved. Rule entry mode exited.
High-Low-Low All criteria or actions were cleared for rule currently being
entered; continue entry of rule.
Low Last saved rule was successfully deleted. The rule presently
being entered is left intact.
Low-High-High All rules are now deleted. The rule presently being entered
is left intact. (This beep sequence has a different meaning
outside of ADF.)
Error Indications. Duration of tones are very long.

Beeper Sequence Indication
Low-High-Low-High Out of rule memory. Erase some existing rules, then try to
save rule again. (The current rule need not be re-entered.)
Low-High-Low Cancel rule entry. Rule entry mode exited because of an
error or the user asked to exit rule entry.
Low-High Entry error, wrong bar code scanned. Re-enter criterion or
action. All previously entered criteria and actions are
retained. Criteria or action list is too long for a rule.
1-11
1-12
Chapter 2
ADF Bar Codes
Special Commands
Begin New Rule

Scan this bar code to start entering a new rule.
BEGIN NEW RULE
Save Rule
Scan this bar code to save the rule you entered.
SAVE RULE
2-1
Erase
Use these bar codes to erase criteria, actions, or rules.
ERASE CRITERIA ERASE ACTIONS

AND START AND START
AGAIN AGAIN
ERASE PREVIOUSLY
SAVED RULE ERASE ALL RULES
Quit Entering Rules

Scan this bar code to quit entering rules.
QUIT ENTERING
RULES
2-2
ADF Bar Codes
Disable Rule Set

Use these bar codes to disable rule sets.
DISABLE RULE SET 1 DISABLE RULE SET 2
DISABLE RULE SET 3 DISABLE RULE SET 4
DISABLE ALL RULE SETS
2-3
Criteria
Code Types
Scan the bar codes for all code types desired before selecting other criteria.
CODE 39 CODABAR
CODE 128 D 2 OF 5
IATA 2 OF 5 I 2 OF 5
CODE 93 UPC-A
UPC-E EAN-8
2-4
ADF Bar Codes
Code Types (Cont’d)
EAN-13 MSI PLESSEY
EAN 128 UPC-E1
BOOKLAND TRIOPTIC
Scan the bar code below only if you are using an

LS 400Xi scanner which supports PDF417.
PDF417
2-5
Code Lengths
Scan these bar codes to define the number of characters the selected code types must contain.
Select one length per rule only.
Note: This is not a keypad.
1 2
3 4
5 6
7 8
2-6
ADF Bar Codes
Code Lengths (Cont’d)
9 10
11 12
13 14
15 16
2-7
17 18
19 20
21 22
23 24
2-8
ADF Bar Codes
25 26
27 28
29 30
2-9
Specific Data String

After scanning the following bar code:
1. Enter a string using the Alphanumeric Keyboard beginning on page 2-66.

2. Scan END OF MESSAGE on page 2-72.
SPECIFIC STRING AT START
After scanning the following bar code:
1. Enter a location using the Numeric Keypad on page 2-11.

2. Enter a string using the Alphanumeric Keyboard beginning on page 2-66.
3. Scan END OF MESSAGE on page 2-72.
SPECIFIC STRING ANY LOCATION
2-10
ADF Bar Codes
Numeric Keypad
Bar codes on this page should not be confused with those on the alphanumeric keyboard.
0 1
2 3
5
4
6 7
9
8
CANCEL
2-11
Rule Belongs To Set

Scan a bar code below to select which set a rule belongs to.
RULE BELONGS TO SET 1 RULE BELONGS TO SET 2
RULE BELONGS TO SET 3 RULE BELONGS TO SET 4
2-12
ADF Bar Codes
Actions
Send Data
Use these bar codes to send data.
SEND DATA UP TO
CHARACTER
SEND ALL DATA THAT SEND NEXT CHARACTER

REMAINS
SEND NEXT SEND NEXT

2 CHARACTERS 3 CHARACTERS
SEND NEXT SEND NEXT

SEND NEXT SEND NEXT

2-13
Send Data (Cont’d)
SEND NEXT 8 SEND NEXT

CHARACTERS 9 CHARACTERS
SEND NEXT SEND NEXT

SEND NEXT SEND NEXT

SEND NEXT SEND NEXT

SEND NEXT SEND NEXT

2-14
ADF Bar Codes
Send Data (Cont’d)
SEND NEXT SEND NEXT

SEND NEXT
20 CHARACTERS
Scan the bar codes below only if you are using an

SEND NEXT SEND NEXT

SEND NEXT SEND NEXT

SEND NEXT
250 CHARACTERS
2-15
Setup Fields
Scan a bar code below to move the cursor in relation to a specified character. Then enter a
character by scanning a bar code from the Alphanumeric Keyboard beginning on page 2-66.
Note: If there is no match when the rule is interpreted and the rule fails, the
next rule is checked.
MOVE CURSOR TO MOVE CURSOR TO START

CHARACTER
MOVE CURSOR PAST SEND PAUSE

CHARACTER
2-16
ADF Bar Codes
Skip Ahead
Use the following bar codes to skip ahead characters.
SKIP AHEAD SKIP AHEAD

1 CHARACTER 2 CHARACTERS



2-17
Skip Ahead (Cont’d)




SKIP AHEAD
250 CHARACTERS
2-18
ADF Bar Codes
Skip Back
Use the following bar codes to skip back characters.
SKIP BACK SKIP BACK

SKIP BACK SKIP BACK

SKIP BACK
5 CHARACTERS SKIP BACK
6 CHARACTERS
SKIP BACK SKIP BACK

7 CHARACTER 8 CHARACTERS
2-19
Skip Back (Continued)
SKIP BACK SKIP BACK


SKIP BACK SKIP BACK

SKIP BACK SKIP BACK

SKIP BACK
250 CHARACTERS
2-20
ADF Bar Codes
Send Preset Value

Use these bar codes to send preset values.
SEND VALUE 1 SEND VALUE 2
2-21
Modify Data
Use the bar codes below to modify data.
REMOVE ALL SPACES CRUNCH ALL SPACES
STOP SPACE REMOVAL REMOVE LEADING

ZEROS
STOP ZERO REMOVAL
2-22
ADF Bar Codes
Pad Data with Spaces

Use these bar codes to pad data with spaces.
PAD SPACES TO PAD SPACES TO

LENGTH 1 LENGTH 2

LENGTH 3 LENGTH 4

LENGTH 5 LENGTH 6

LENGTH 7 LENGTH 8
2-23
Pad Data with Spaces (Cont’d)

LENGTH 9 LENGTH 10

LENGTH 11 LENGTH 12

LENGTH 13 LENGTH 14

LENGTH 15 LENGTH 16
2-24
ADF Bar Codes
Pad Data with Spaces (Cont’d)

LENGTH 17 LENGTH 18

LENGTH 19 LENGTH 20

LENGTH 21 LENGTH 22

LENGTH 23 LENGTH 24
2-25
Pad Data with Spaces (Continued)

LENGTH 25 LENGTH 26

LENGTH 27 LENGTH 28

LENGTH 29 LENGTH 30
STOP PAD SPACES
2-26
ADF Bar Codes
Pad Data with Zeros

Use these bar codes to pad data with zeros.
PAD ZEROS TO PAD ZEROS TO

LENGTH 1 LENGTH 2

LENGTH 3 LENGTH 4

LENGTH 5 LENGTH 6

LENGTH 7 LENGTH 8
2-27
Pad Data With Zeros (Cont’d)

LENGTH 9 LENGTH 10

LENGTH 11 LENGTH 12

LENGTH 13 LENGTH 14

LENGTH 15 LENGTH 16
2-28
ADF Bar Codes

LENGTH 17 LENGTH 18

LENGTH 19 LENGTH 20

LENGTH 21 LENGTH 22

LENGTH 23 LENGTH 24
2-29

LENGTH 25 LENGTH 26

LENGTH 27 LENGTH 28

LENGTH 29 LENGTH 30
STOP PAD ZEROS
2-30
ADF Bar Codes
Beeps
Select one beep sequence per ADF rule.
BEEP ONCE
BEEP TWICE
BEEP THREE TIMES
2-31
Control Characters
Scan these bar codes to send control characters.
SEND CONTROL 2 SEND CONTROL A
SEND CONTROL B SEND CONTROL C
SEND CONTROL D SEND CONTROL E
SEND CONTROL F SEND CONTROL G
2-32
ADF Bar Codes
Control Characters (Cont’d)
SEND CONTROL H SEND CONTROL I
SEND CONTROL J SEND CONTROL K
SEND CONTROL L SEND CONTROL M
SEND CONTROL N SEND CONTROL O
2-33
SEND CONTROL P SEND CONTROL Q
SEND CONTROL R SEND CONTROL S
SEND CONTROL T SEND CONTROL U
SEND CONTROL V SEND CONTROL W
2-34
ADF Bar Codes
SEND CONTROL X SEND CONTROL Y
SEND CONTROL Z SEND CONTROL [
SEND CONTROL \ SEND CONTROL ]
SEND CONTROL 6 SEND CONTROL -
2-35
Keyboard Characters
Use these bar codes to send keyboard characters.
SEND SPACE SEND !
SEND “ SEND #
SEND $ SEND %
SEND & SEND ‘
2-36
ADF Bar Codes
Keyboard Characters (Cont’d)
SEND ( SEND )
SEND * SEND +
SEND , SEND -
SEND . SEND /
2-37
SEND 0 SEND 1
SEND 2 SEND 3
SEND 4 SEND 5
SEND 6 SEND 7
2-38
ADF Bar Codes
SEND 8 SEND 9
SEND : SEND ;
SEND < SEND =
SEND > SEND ?
2-39
SEND @ SEND A
SEND B SEND C
SEND D SEND E
SEND F SEND G
2-40
ADF Bar Codes
SEND H SEND I
SEND J SEND K
SEND L SEND M
SEND N SEND O
2-41
SEND P SEND Q
SEND R SEND S
SEND T SEND U
SEND V SEND W
2-42
ADF Bar Codes
SEND X SEND Y
SEND Z SEND [
SEND \ SEND ]
SEND ^ SEND _
2-43
SEND ‘ SEND a
SEND b SEND c
SEND d SEND e
SEND f SEND g
2-44
ADF Bar Codes
SEND h SEND i
SEND j SEND k
SEND l SEND m
SEND n SEND o
2-45
SEND p SEND q
SEND r SEND s
SEND t SEND u
SEND v SEND w
2-46
ADF Bar Codes
SEND x SEND y
SEND z SEND {
SEND | SEND }
SEND ~
2-47
Send ALT Characters
SEND ALT 2 SEND ALT A
SEND ALT B SEND ALT C
SEND ALT D SEND ALT E
SEND ALT F SEND ALT G
2-48
ADF Bar Codes
Send ALT Characters (Cont’d)
SEND ALT H SEND ALT I
SEND ALT J SEND ALT K
SEND ALT L SEND ALT M
SEND ALT N SEND ALT O
2-49
SEND ALT P SEND ALT Q
SEND ALT R SEND ALT S
SEND ALT T SEND ALT U
SEND ALT V SEND ALT W
2-50
ADF Bar Codes
SEND ALT X SEND ALT Y
SEND ALT Z SEND ALT [
SEND ALT \ SEND ALT ]
SEND ALT 6 SEND ALT -
2-51
Send Command Characters
SEND PA 1 SEND PA 2
SEND CMD 1 SEND CMD 2
2-52
ADF Bar Codes
Send Command Characters (Cont’d)
2-53
Send Special Characters
SEND YEN SEND POUND STERLING

CHARACTER CHARACTER
SEND BOMB SEND HOOK

CHARACTER CHARACTER
SEND BULLET SEND 1/2

CHARACTER CHARACTER
SEND PARAGRAPH SEND SECTION

CHARACTER CHARACTER
SEND VERTICAL
CHARACTER
2-54
ADF Bar Codes
Send Keypad Characters
SEND KEYPAD * SEND KEYPAD +
SEND KEYPAD - SEND KEYPAD .
SEND KEYPAD / SEND KEYPAD 0
SEND KEYPAD 1 SEND KEYPAD 2
2-55
Send Keypad Characters (Cont’d)
SEND KEYPAD 9 SEND KEYPAD ENTER
SEND KEYPAD
NUM LOCK
2-56
ADF Bar Codes
SEND BREAK KEY SEND DELETE KEY
SEND PAGE UP KEY SEND END KEY
SEND PAGE DOWN SEND PAUSE KEY

KEY
SEND SCROLL LOCK SEND BACKSPACE

KEY KEY
SEND TAB KEY SEND PRINT SCREEN

KEY
2-57
SEND INSERT KEY SEND HOME KEY
SEND ENTER KEY SEND ESCAPE KEY
SEND UP ARROW KEY SEND DOWN ARROW

KEY
SEND LEFT ARROW SEND RIGHT ARROW

KEY KEY
SEND BACK TAB

CHARACTER
2-58
ADF Bar Codes
Send Function Key
SEND F1 KEY SEND F2 KEY
2-59
Send Function Key (Cont’d)
2-60
ADF Bar Codes
2-61
SEND PF1 KEY SEND PF2 KEY
2-62
ADF Bar Codes
2-63
2-64
ADF Bar Codes
Turn On/Off Rule Set

Use these bar codes to turn rule sets on and off.
TURN ON RULE SET 1 TURN ON RULE SET 2
TURN ON RULE SET 3 TURN ON RULE SET 4
TURN OFF RULE SET 1 TURN OFF RULE SET 2
TURN OFF RULE SET 3 TURN OFF RULE SET 4
2-65
Alphanumeric Keyboard
SPACE #
$ %
* +
- .
/ !
2-66
ADF Bar Codes
Alphanumeric Keyboard (Continued)
“ &
‘ (
) :
; <
= >
2-67
? @
[ \
] ^
_ `
2-68
ADF Bar Codes

Bar codes on this page should not be confused with those on the numeric keypad.
0 1
2 3
4 5
6 7
8 9
2-69
A B
C D
E F
G H
I J
2-70
ADF Bar Codes
K L
M N
O P
Q R
S T
2-71
U V
W X
Y Z
CANCEL END OF MESSAGE
2-72
ADF Bar Codes
a b
c d
e f
g h
i j
2-73
k l
m n
o p
q r
s t
2-74
ADF Bar Codes
u v
w x
y z
{ |
} ~
2-75
2-76
Appendix A
ASCII Tables and Keyboard Layouts
Prefix / Suffix Values

The following values can be assigned as prefixes or suffixes for ASCII character data
transmission. If you’re using a keyboard interface, refer to the Synapse “Smart Cable”
Interface Guide for keystroke prefix/suffix values.
A-1
Table A-1. Prefix/Suffix Values
Prefix/Suf- Full ASCII Code ASCII Prefix/Suf- Full ASCII Code ASCII
fix Value 39 Encode Char. Character fix Value 39 Encode Char. Character
1000 %U NUL 1030 %D RS
1001 $A SOH 1031 %E US
1002 $B STX 1032 Space Space
1003 $C ETX 1033 /A !
1004 $D EOT 1034 /B "
1005 $E ENQ 1035 /C #
1006 $F ACK 1036 /D $
1007 $G BELL 1037 /E %
1008 $H BCKSPC 1038 /F &
1009 $I HORIZ TAB 1039 /G ‘
1010 $J LF/NW LN 1040 /H (
1011 $K VT 1041 /I )
1012 $L FF 1042 /J *
1013 $M CR/ENTER 1043 /K +
1014 $N SO 1044 /L ,
1015 $O SI 1045 - -
1016 $P DLE 1046 . .
1017 $Q DC1 1047 / /
1018 $R DC2 1048 0 0
1019 $S DC3 1049 1 1
1020 $T DC4 1050 2 2
1021 $U NAK 1051 3 3
1022 $V SYN 1052 4 4
1023 $W ETB 1053 5 5
1024 $X CAN 1054 6 6
1025 $Y EM 1057 7 7
1026 $Z SUB 1056 8 8
1027 %A ESC 1057 9 9
1028 %B FS 1058 /Z :
1029 %C GS 1059 %F ;
A-2
Table A-1. Prefix/Suffix Values (Cont’d)

Prefix/Suf- Full ASCII Code ASCII Prefix/Suf- Full ASCII Code ASCII
fix Value 39 Encode Char. Character fix Value 39 Encode Char. Character
1060 %G < 1095 %O _
1061 %H = 1096 %W `
1062 %I > 1097 +A a
1063 %J ? 1098 +B b
1064 %V @ 1099 +C c
1065 A A 1100 +D d
1066 B B 1101 +E e
1067 C C 1102 +F f
1068 D D 1103 +G g
1069 E E 1104 +H h
1070 F F 1105 +I i
1071 G G 1106 +J j
1072 H H 1107 +K k
1073 I I 1108 +L l
1074 J J 1109 +M m
1075 K K 1110 +N n
1076 L L 1111 +O o
1077 M M 1112 +P p
1078 N N 1113 +Q q
1079 O O 1114 +R r
1080 P P 1115 +S s
1081 Q Q 1116 +T t
1082 R R 1117 +U u
1083 S S 1118 +V v
1084 T T 1119 +W w
1085 U U 1120 +X x
1086 V V 1121 +Y y
1087 W W 1122 +Z z
1088 X X 1123 %P {
1089 Y Y 1124 %Q |
1090 Z Z 1125 %R }
1091 %K [ 1126 %S ~
1092 %L \ 1127 Undefined
1093 %M ]
1094 %N ^ 7013 ENTER
A-3
ASCII Character Set

Table A-2. ASCII Character Se t
ASCII Full ASCII Keystroke ASCII Full ASCII Keystroke
Value Code 39 Value Code 39
Encode Char. Encode Char
1000 %U CTRL 2 1024 $X CTRL X
1001 $A CTRL A 1025 $Y CTRL Y
1002 $B CTRL B 1026 $Z CTRL Z
1003 $C CTRL C 1027 %A CTRL [
1004 $D CTRL D 1028 %B CTRL \
1005 $E CTRL E 1029 %C CTRL ]
1006 $F CTRL F 1030 %D CTRL 6
1007 $G CTRL G 1031 %E CTRL -
1008 $H CTRL H 1032 Space Space
1009 $I CTRL I 1033 /A !
1010 $J CTRL J 1034 /B ‘
1011 $K CTRL K 1035 /C #
1012 $L CTRL L 1036 /D $
1013 $M CTRL M 1037 /E %
1014 $N CTRL N 1038 /F &
1015 $O CTRL O 1039 /G ‘
1016 $P CTRL P 1040 /H (
1017 $Q CTRL Q 1041 /I )
1018 $R CTRL R 1042 /J *
1019 $S CTRL S 1043 /K +
1020 $T CTRL T 1044 /L ,
1021 $U CTRL U 1045 - -
1022 $V CTRL V 1046 . .
1023 $W CTRL W 1047 / /
1048 0 0 1073 I I
A-4
Table A-2. ASCII Character Set (Cont’d)

1049 1 1 1074 J J
1050 2 2 1075 K K
1051 3 3 1076 L L
1052 4 4 1077 M M
1053 5 5 1078 N N
1054 6 6 1079 O O
1055 7 7 1080 P P
1056 8 8 1081 Q Q
1057 9 9 1082 R R
1058 /Z : 1083 S S
1059 %F ; 1084 T T
1060 %G < 1085 U U
1061 %H = 1086 V V
1062 %I > 1087 W W
1063 %J ? 1088 X X
1064 %V @ 1089 Y Y
1065 A A 1090 Z Z
1066 B B 1091 %K [
1067 C C 1092 %L \
1068 D D 1093 %M ]
1069 E E 1094 %N ^
1070 F F 1095 %O _
1071 G G 1096 %W ‘
1072 H H 1097 +A a
1098 +B b 1113 +Q q
1099 +C c 1114 +R r
1100 +D d 1115 +S s
A-5

1101 +E e 1116 +T t
1102 +F f 1117 +U u
1103 +G g 1118 +V v
1104 +H h 1119 +W w
1105 +I i 1120 +X x
1106 +J j 1121 +Y y
1107 +K k 1122 +Z z
1108 +L l 1123 %P {
1109 +M m 1124 %Q |
1110 +N n 1125 %R }
1111 +O o 1126 %S ~
1112 +P p 1127 Undefined
A-6

ALT Keys Keystroke ALT Keys Keystroke ALT Keys Keystroke
2064 ALT 2 2075 ALT K 2086 ALT V
2065 ALT A 2076 ALT L 2087 ALT W
2066 ALT B 2077 ALT M 2088 ALT X
2067 ALT C 2078 ALT N 2089 ALT Y
2068 ALT D 2079 ALT O 2090 ALT Z
2069 ALT E 2080 ALT P 2091 ALT [
2070 ALT F 2081 ALT Q 2092 ALT \
2071 ALT G 2082 ALT R 2093 ALT ]
2072 ALT H 2083 ALT S 2094 ALT 6
2073 ALT I 2084 ALT T 2095 ALT -
2074 ALT J 2085 ALT U
Misc. Key Keystroke Misc. Key Keystroke Misc. Key Keystroke

3001 PA 1 3009 CMD 7 3017 °
3002 PA 2 3010 CMD 8 3018 1/2
3003 CMD 1 3011 CMD 9 3019 ¶
3004 CMD 2 3012 CMD 10 3020 §
3005 CMD 3 3013 ¥ 3021 |
3006 CMD 4 3014 £ 3022 0/00
3007 CMD 5 3015 ¤
3008 CMD 6 3016 ¬
A-7

PF Keys Keystroke PF Keys Keystroke PF Keys Keystroke
4001 PF 1 4009 PF 9 4017 PF 17
4002 PF 2 4010 PF 10 4018 PF 18
4003 PF 3 4011 PF 11 4019 PF 19
4004 PF 4 4012 PF 12 4020 PF 20
4005 PF 5 4013 PF 13 4021 PF 21
4006 PF 6 4014 PF 14 4022 PF 22
4007 PF 7 4015 PF 15 4023 PF 23
4008 PF 8 4016 PF 16 4024 PF 24
F Keys Keystroke F Keys Keystroke F Keys Keystroke

5001 F1 5014 F 14 5027 F 27
5002 F2 5015 F 15 5028 F 28
5003 F3 5016 F 16 5029 F 29
5004 F4 5017 F 17 5030 F 30
5005 F5 5018 F 18 5031 F 31
5006 F6 5019 F 19 5032 F 32
5007 F7 5020 F 20 5033 F 33
5008 F8 5021 F 21 5034 F 34
5009 F9 5022 F 22 5035 F 35
5010 F 10 5023 F 23 5036 F 36
5011 F 11 5024 F 24 5037 F 37
5012 F 12 5025 F 25 5038 F 38
5013 F 13 5026 F 26 5039 F 39
A-8

Numeric Keystroke Numeric Keystroke Numeric Keystroke
Keypad Keypad Keypad
6042 * 6049 1 6056 8
6043 + 6050 2 6057 9
6044 Undefined 6051 3 6058 Enter
6045 - 6062 4 6059 Num Lock
6046 . 6063 5 6060 00
6047 / 6064 6
6048 0 6065 7
Extended Keystroke Extended Keystroke Extended Keystroke

Keypad Keypad Keypad
7001 Break 7008 Backspace 7015 Up Arrow
7002 Delete 7009 Tab 7016 Dn Arrow
7003 Pg Up 7010 Print Screen 7017 Left Arrow
7004 End 7011 Insert 7018 Right Arrow
7005 Pg Dn 7012 Home 7019 Back Tab
7006 Pause 7013 Enter
7007 Scroll Lock 7014 Escape
A-9
Keyboard Maps
IBM PC/XT TANDY HD 1200 ITT PC
NCR PC4 ADDS PC I/II SPERRY PC
COMPAQ DESKPRO LEADING EDGE PC PITNEY BOWES A2000
COLUMBIA PC HP VECTRA CS/RS
IBM PC/AT NCR PC8 ZENITH 248
WYSE PC
A-10
IBM 3179 IBM 3180 IBM 319X
IBM 347X TELEX 122
IBM PS2 COMPAQ 386 WYSE PC ENHANCED
HP VECTRA ES/QS
A-11
*3001 for IBM 3151

IBM 3151 DEC VT2XX/VT3XX/VT4XX IBM 316X
TEXAS INSTRUMENTS 924
TELEX 88
A-12
WYSE 50
WYSE 60 ANSI KYBD
A-13
WYSE 60 ASCII KYBD
WYSE 60/85/150/185
A-14
DECISION DATA 3496
DECISION DATA 3761
A-15
DECISION DATA 359X
A-16
IBM 3178
HP 239X
A-17
HP 700/9X
A-18
IBM 3278
A-19
NCR 2151
NCR 2152 27-KEY
A-20
NCR 2155
NCR 2157
A-21
NCR 280
NCR 2950
A-22
NCR 7052 32-KEY
NCR 7052 58-KEY
A-23
IBM 3683/3684 35-KEY Calculator Style
IBM 3683/3684 35-KEY Phone Style
A-24
IBM 3683/3684 48-KEY Calculator Style
IBM 3683/3684 48-KEY Phone Style
A-25
IBM 3683 116-KEY
IBM 3653 30-KEY
A-26
Index
A bar code menu example . . . . . . . . . . . . 1-6
actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 beep . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
ADF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 beeper definitions . . . . . . . . . . . . . . . 1-11
actions . . . . . . . . . . . . . . . . . 1-1, 1-4, 2-13 code length . . . . . . . . . . . . . . . . . . . . . 1-3
alphanumeric keyboard . . . . . . . . . . . 2-66 code lengths . . . . . . . . . . . . . . . . . . . . . 2-6
alternate rule sets . . . . . . . . . . . . . . . . . 1-8 code types . . . . . . . . . . . . . . . . . . . 1-3, 2-4
bar code menu example . . . . . . . . . . . . 1-6 criteria . . . . . . . . . . . . . . . . . . . . . . 1-1, 2-4
beep . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31 default rules . . . . . . . . . . . . . . . . . . . . 1-10
beeper definitions . . . . . . . . . . . . . . . . 1-11 numeric keypad . . . . . . . . . . . . . . . . . 2-11
code length . . . . . . . . . . . . . . . . . . . . . . 1-3 pad spaces . . . . . . . . . . . . . . . . . . . . . 2-23
code lengths . . . . . . . . . . . . . . . . . . . . . 2-6 pad zeros . . . . . . . . . . . . . . . . . . . . . . 2-27
code types . . . . . . . . . . . . . . . . . . 1-3, 2-4 rule belongs to set . . . . . . . . . . . . . . . 2-12
criteria . . . . . . . . . . . . . . . . . . . . . 1-1, 2-4 rules . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
default rules . . . . . . . . . . . . . . . . . . . . 1-10 rules heirarchy . . . . . . . . . . . . . . . . . . . 1-9
numeric keypad . . . . . . . . . . . . . . . . . 2-11 send characters . . . . . . . . . . . . . . . . . 2-13
pad spaces . . . . . . . . . . . . . . . . . . . . . 2-23 send control characters . . . . . . . . . . . 2-32
pad zeros . . . . . . . . . . . . . . . . . . . . . . 2-27 send value . . . . . . . . . . . . . . . . . . . . . 2-21
rule belongs to set . . . . . . . . . . . . . . . 2-12 setup fields . . . . . . . . . . . . . . . . . . . . 2-16
rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 skip ahead characters . . . . . . . . . . . . 2-17
rules heirarchy . . . . . . . . . . . . . . . . . . . 1-9 skip back characters . . . . . . . . . . . . . 2-19
send characters . . . . . . . . . . . . . . . . . . 2-13 space removal . . . . . . . . . . . . . . . . . . 2-22
send control characters . . . . . . . . . . . . 2-32 special commands . . . . . . . . . . . . . . . . 2-1
send value . . . . . . . . . . . . . . . . . . . . . 2-21 specific data string . . . . . . . . . . . . . . . 2-10
setup fields . . . . . . . . . . . . . . . . . . . . . 2-16 zero removal . . . . . . . . . . . . . . . . . . . 2-22
skip ahead characters . . . . . . . . . . . . . 2-17
skip back characters . . . . . . . . . . . . . . 2-19 B
space removal . . . . . . . . . . . . . . . . . . . 2-22 beeper
special commands . . . . . . . . . . . . . . . . . 2-1 ADF definitions . . . . . . . . . . . . . . . . . 1-11
specific data string . . . . . . . . . . . . . . . 2-10 bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
zero removal . . . . . . . . . . . . . . . . . . . . 2-22
advanced data formatting . . . . . . . . . . . . . . 1-1
actions . . . . . . . . . . . . . . . . . 1-1, 1-4, 2-13 C
alphanumeric keyboard . . . . . . . . . . . 2-66 code types
alternate rule sets . . . . . . . . . . . . . . . . . 1-8 ADF . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Index-1
conventions N
notational . . . . . . . . . . . . . . . . . . . . . . . . v notational conventions . . . . . . . . . . . . . . . . . . .v
criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
R
I related publications . . . . . . . . . . . . . . . . . . . . .v
information
service . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
S
service information . . . . . . . . . . . . . . . . . . . . vi
Symbol Support Center . . . . . . . . . . . . . . . . .vii
Index-2
Tell Us What You Think...
We’d like to know what you think about this Manual. Please take a moment
to fill out this questionaire and fax this form to: (631) 738-3318, or mail to:
Symbol Technologies, Inc.

One Symbol Plaza M/S B-4
Holtsville, NY 11742-1300
Attn: Technical Publications Manager
IMPORTANT: If you need product support, please call the appropriate cus-
tomer support number provided. Unfortunately, we cannot provide customer
support at the fax number above.
User’s Manual Title: _______________________________________________

(please include revision level)
How familiar were you with this product before using this manual?
Very familiar Slightly familiar Not at all familiar
Did this manual meet your needs? If not, please explain. ________________
________________________________________________________________
What topics need to be added to the index, if applicable? _______________

________________________________________________________________
What topics do you feel need to be better discussed? Please be specific.

_________________________________________________________________
What can we do to further improve our manuals?_______________________

_________________________________________________________________
_________________________________________________________________
Thank you for your input—We value your comments.

Symbol ls4000 Programmers Guide

Uploaded by

Copyright:

Available Formats

Symbol ls4000 Programmers Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Symbol ls4000 Programmers Guide

Uploaded by

Copyright:

Available Formats

What is the document about?

What is the document about?

What information is included in the table of contents?

What information is included in the table of contents?

LS 4000 and

Advanced Programmer’s Guide

2 Symbol Technologies, Inc. One Symbol Plaza, Holtsville N.Y. 11742-1300

No license is granted, either expressly or by implication, estoppel, or otherwise under any

About This Manual

Chapter 1. Advanced Data Formatting

Chapter 2. ADF Bar Codes

Appendix A. ASCII Tables and Keyboard Layouts

The LS 4000 and LS 400Xi Advanced Programmers Guide provides programming

! LS 4000 refers to the LS 4000 series of scanners

Note: Symbol Technologies is not responsible for any damages incurred

Symbol Support Center

SYMBOL SUPPORT Europe/Mid-East Distributor Operations

Warranty Coverage and Procedure

Rules: Criteria Linked to Actions

For instance, a data formatting rule could be the following:

Using ADF Bar Codes

To program each data formatting rule:

Begin New Rule

Quit Entering Rules

Disable Rule Set

Message Containing A Specific Data String

Specific String at Start

Specific String, Any Location

Rule Belongs To Set

Move Cursor To a Character

Move Cursor to Start of Data

Move Cursor Past a Character

Skip Ahead “N” Characters

Skip Back “N” Characters

Send Preset Value

Value 1 = Scan Suffix

Remove All Spaces

Crunch All Spaces

Stop Space Removal

Remove Leading Zeros

Stop Zero Removal

Pad Data With Spaces

Pad Data With Zeros

Send Keystroke (Control Characters and Keyboard Characters)

Turn On/Off Rule Sets

ADF Bar Code Menu Example

The following rules need to be entered:

Rule 1: The Code 128 Scanning Rule

Rule 2: The UPC Scanning Rule

Alternate Rule Sets

Class (2 digits), Stock Number (8) digits, Price (5 digits)

Rules Hierarchy (in Bar Codes)

When receiving scan data, send all data.

Error Indications. Duration of tones are very long.

Begin New Rule

BEGIN NEW RULE

ERASE CRITERIA ERASE ACTIONS

Quit Entering Rules

Disable Rule Set