1

Fall 2007
EE221
Introduction to Multisim

Multisim is a simulation tool that can be used to expedite the analysis and design of various
circuits, including ones containing digital devices, transistors, diodes, op amps, and even motors.
This handout is not intended to be exhaustive, but rather it will get you started in simulating
Direct Current (DC) circuits. Alternating Current (AC), transient, and frequency response
capabilities will be discussed later in the course. You are encouraged to actively use Multisim as
you are proceeding through this introduction.

To start Multisim, select from the program list:

It should bring up a window similar to that shown in Figure 1 (the window to the left of this can
be closed – it is available for managing multiple project windows). If you do not see a grid, select
from the top toolbar
VIEW -> SHOW GRID

SHORT-CUT TO SHORT-CUT TO
MEASUREMENT PLACE PARTS PLACE METERING
COMMON LIBRARIES DEVICES
OF PARTS

DIGITAL MULTI-METER

Figure 1: Blank Circuit Sheet (Project Window) when Multisim is Activated

Note this “sheet of paper” is where you will construct the circuit of interest. The icons on the
right of Figure 1 are measurement and instrumentation equipment such as DMM’s, function
generators, wattmeters, etc. The components you need today are available via the toolbar just
above the blank sheet (see Fig. 1). The buttons towards the left will access some of the most
important libraries where sources and resistors may be found. For instance, to specify a DC
source, you can mouse-select the first button on the lower left which opens the SOURCES
library. The first entry (family) is POWER_SOURCES and the second Component is the
DC_POWER source which we can see in Figure 2. Double-clicking the DC_POWER entry will
allow you to bring the source into the project workspace and locate it via the mouse.

Figure 2: Navigating the SOURCES Library

Alternatively, as shown in Figure 1, the right-side of the lower toolbar also provides a short cut to
some frequently-used parts. For example the DC source can also be located and placed by
clicking the blue button furthest to the left as shown in Figure 3 and double-clicking PLACE DC
VOLTAGE SOURCE. By double-clicking the icon in the project window, you can adjust any
parameters available for a part. For instance for the DC VOLTAGE SOURCE, the voltage value
is one obvious parameter.
 3

Figure 3: Short-Cut Placement of DC Power Source

Let’s consider next that we wish to “simulate” the circuit shown in Figure 4, including inserting
the appropriate measurement devices. Note the resistors can be found by selecting the second
icon on the lower toolbar (the BASIC Group), then choosing the BASIC_VIRTUAL Family, and
finally RESISTOR_VIRTUAL for the component. The advantage of the virtual resistor is that
you can set it to any value, as compared to the RESISTOR family where only standard values are
available (though with tolerances). The virtual resistor can also be placed by clicking the third
blue button from the left and selecting PLACE VIRTUAL RESISTOR. The meters are found at
the eighth blue button. Note we want a “Horizontal” oriented ammeter (terminals on the left and
right) and a “Vertical” oriented voltmeter (terminals on the top and bottom). Upon collecting
these six components, your project workspace should appear as shown in Figure 5. Note the
resistors are 1k , the ammeter has an internal resistance of 1e  9 , and the voltmeter has an
internal resistance of 10M  .

10
+
A
+

+ 100 V
12V
-
10

Figure 4: Desired Circuit

Figure 5: Collection of Components and Meters Required

Most importantly, every circuit that we build must have a ground reference. It is found in the
SOURCES – POWER_SOURCES library or via the first blue button on the left. This is the
symbol found in the lower left part of the project workspace. If “ground” is not specified, the
circuit will not simulate.

Note, we can change the resistor values by double-clicking the icon and entering the new
resistance. We can rotate components by right-clicking the icon and selecting, for instance, 90
Clockwise. Finally, we can move components by left-selecting them and moving the mouse
pointer to the desired location as shown in Figure 6.
 5

Figure 6: Component Values Adjusted and Icons Realigned

Finally, components are interconnected by single left clicking one terminal of Part A, extending
the wire over to Part B, and completing the connection by left-clicking on one of the terminals of
Part B. Once a wire is positioned, you may also connect a component to the wire in a similar
manner. To have Multisim list the node numbers on the circuit, from the top toolbar select

OPTIONS -> SHEET PROPERTIES-> NET NAMES (Check Show All)

The final rendering of the circuit of Figure 4 is then shown in Figure 7. Note that the “ground”
node is always specified as node 0.
 6

Figure 7: Final Interconnected Circuit

Note that if we wish to mimic what we encountered in Lab #1 where the ammeter resistance
noticeably effected our measured, we need to change the internal resistance to about 5.5 . To
do this, double-click the ammeter icon and change the resistance value. To then “run” the
simulation, you need to specify

SIMULATE -> RUN

from the top toolbar or simply press the lightning bolt button in the middle toolbar. Note this
button also allows you to stop the simulation. The results for our circuit are shown in Figure 8.
 7

START/STOP
SIMULATION

Figure 8: Simulation with Real Ammeter Included

If you wish to modify the circuit, you must first “stop” the simulation, then you can change
parameter values, delete connections, or add new components. This should be enough of an
introduction for now to allow you to create DC circuits and measure quantities of interest using
available meters.