Scribd
Upload
639 views

Ericsson Commands

This document provides instructions for various commands to monitor different elements of an Ericsson mobile network, including: 1. Commands to perform performance tests, see status, and block/deblock TRX units. 2. Commands to see active alarms, signaling status, and cell configuration details for a BSC. 3. Commands to check loop status and traffic channel numbers for sites, and monitor signaling points and frequency information for cells.

Uploaded by

sunny kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
639 views

Ericsson Commands

This document provides instructions for various commands to monitor different elements of an Ericsson mobile network, including: 1. Commands to perform performance tests, see status, and block/deblock TRX units. 2. Commands to see active alarms, signaling status, and cell configuration details for a BSC. 3. Commands to check loop status and traffic channel numbers for sites, and monitor signaling points and frequency information for cells.

Uploaded by

sunny kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

Ericsson Command Handling1.

Giving Performance test against a TRX


rxbli:mo=rxotrx-395-5; (Block)rxtei:mo=rxotrx-395-5; (Perf. Test)rxble:mo=rxotrx-
395-5; (Deblock)
2. To see the frequency state of a TRX(With fault code)
rxmfp:mo=rxotrx-395-5;
3. To see TRX status
1. rxmsp:mo=rxotrx-395-5; (For having only one TRX status)2. rxmsp:mo=rxotrx-395-
4&&-5; (for having two or more TRX status
4. To see all (TX,TS,TRX) status
rxmsp:mo=rxotrx-395-5,subord;
Note: State, BLO, BLA all the values will be zero for active TRX (TRX in good
condition)5. To find the TG value of a Site
rxtcp:moty=rxotg , cell=dx03214;
6. To see all external alarm of a BSC
allip:alcat=bts;
7. To see all internal alarm of a BSC
allip:alcat=sw_dev;
8. To see active alarm of a BSC
allip; (For all the active alarm of a BSC)allip:acl=a1; (where a1=critical alarm
only)allip:acl=a2; (where a2=major alarm only)allip:acl=a3; (where a3=minor alarm
only)allip:acl=a1,alcat=ext/bts; (for critical ext alarms)
9. To see the total number of TRX of a Site
rxcdp:mo=rxotg-27,details; (where 27 is the TG value of 900B of a site.)
10. Block-Deblock of a TRX
rxbli:mo=rxotrx-23-0,subord; (Block)rxese:mo=rxotrx-23-0,subord; (Reload
Order)rxesi:mo=rxotrx-23-0,subord; (Reload Execute)

rxble:mo=rxotrx-23-0,subord;(Deblock)
11. TRX no. of 900B and 1800B 900B Cell 1800B Cell1 2 3 1 2 3
(No. of Cell) 0 4 8 0 4 8 |1 5 9 1 5 9 |2 6 10 2 6 10 | (No.3 7 11 3 7 11
12. To find out The RBL2,RBLTB,RBLT2 number of a Specific site
a) rxapp:mo=rxotg-353; where 353 is the TG value of a site b)ntcop:snt=all;
Note: Searching format to find out the Fault description, Action from the PDF file:
No of class: faultcode. Example: 1B:33, 2A:3013. To see the GPRS Status of a BSC
rrgbp;
14. Lock-unlock of a TRX(including all TX,TS etc corresponding the TRX)
rxbli:mo=rxotrx-23-0,subord; (Lock)rxble:mo=rxotrx-23-0,subord; (Unlock)
15. Lock-unlock of a TRX(excluding all TX,TS etc corresponding the TRX)
rxbli:mo=rxotrx-23-0; (Lock)rxble:mo=rxotrx-23-0; (Unlock)
16. Lock � unlock of a cell
rlstc:cell=dx12341,state=halted; (The first cell lock of DHK_X1234
site)rlstc:cell=dx12341,state=active; (The first cell unlock of
DHK_X1234)rlstc:cell=dx12341,chgr=1,state=active; (The first cell of 1800 band
unlock of DHK_X1234)
17. To check the RBL2 of a site either it is Working or not (Loop check)
dtstp:dip=84rbl2; (where 84 is the rbl2 number of a site)
18.To check PCMS loop from BSC end of a site
dtstp:dip=84rtltb;
19.To check PCMS loop from TRAU end of a site
dtstp:dip=84rtltt;
20.To know the time from the system

caclp;
21.To find the number of traffic channel of a site
rxapp:mo=rxotg-6; where 6 is the TG value.
22. To get all the signaling of a BSC
c7ltp:ls=all;23
. To clear �digital path quality supervision�alarm
dtqsr:dip=all,es;dtqsr:dip=all,cs2;dtqsr:dip=all,ses;dtqsr:dip=all,ses2;dtqsr:dip=a
ll,sf;
24. To look into either a cell holding call or to see channel status
rlcrp:cell=dx00932;
25. To monitor signaling point
c7spp:sp=all;
27. To know frequency of all BTS in a BSC
1. rlcfp:cell=all; (For all BTS)2. rlcfp:cell=dx00501; (For a specific cell)
27. To know cell configuration frequency data
rlcfp:cell=dx00931; (Where 1 is for 1st cell of DHK_X0093)
28. To have all the data of a cell
rldep:cell=dx00931;
29. To get either a cell is 900B or 1800B
Lj-l
30. The command to point the connected BSC�s for the TRC
rrbsp;
31. The command of getting the name of MSC to which BSC is connected
rrmbp;
32. To have the name of all MSC
rrmbp:msc=all;
33. To see all PCM status

You might also like