USER GUIDE

CLSV-B4KS
CLSV-B4BS
SAFETY GUIDE support.vax.co.uk 2

This machine is intended for • Don’t charge the battery outdoors, or

household use only and NOT for leave the charger connected to the
commercial or industrial use. mains when not in use.
PLEASE KEEP INSTRUCTIONS FOR • Don’t use the machine with a
FURTHER USE AND USE ONLY AS damaged battery. If the battery is
INSTRUCTED IN THIS GUIDE. damaged contact us on: 08000
927737.
DON’TS • Don’t over fill the dirt container to
• Don’t leave the charger plugged in avoid blocking the air flow through
when unattended. the machine.
• Don’t use the machine if it is faulty • The brushbar in the powered
or has been dropped, damaged or floorhead constantly rotates
left outdoors. when switched on. Never use the
• Don’t use the machine to pick up any powered floorhead on one spot for
flammable or combustible materials an extended period of time as the
(lighter fluid, petrol, kerosene etc.) brushbar may damage the floor
or use the machine in an area with surface.
explosive vapours or liquid.
• Don’t use the machine to pick up hot DO’S
coals, cigarette butts, matches or • Only VAX ONEPWR batteries
smoking hot burning items or use in (BV15020/BV15030/BV25040) and
an area where there may be harmful charger (BV05100UK) should be
fluids (chlorine, bleach and ammonia used with this machine.
drain cleaner). • Always stand the charger on a
stable, level surface, uncovered and
• Don’t handle the charger, battery or
away from any heat source.
use the machine with wet hands.
• Only VAX ONEPWR recommended
• Don’t unplug the charger by pulling
tools and accessories should be
on the power cord.
used with this machine.
• The power cord cannot be replaced.
• Always remove the battery from the
If the cord is damaged the charger
machine before carrying out any
should be scrapped.
maintenance or if storing unused for
• Don’t attempt to remove blockages
a long period of time.
with sharp objects as this may cause
• Keep all openings clear and free
damage to the machine.
from debris as this may affect the
• Don’t use the machine with the
airflow/suction.
incorrect battery or charger as this
• Turn off all controls on the machine
may result in damage or injury to the
before disconnecting or connecting
user. The correct battery charger
the battery.
information is listed on the battery
pack ratings label.
SAFETY GUIDE support.vax.co.uk 3
• Only use the machine indoors on dry • Always check the powered floorhead
surfaces and keep the area you’re and accessories are free from
cleaning well lit. damage, dirt and debris before
• This machine is not intended to be using.
used or cleaned by persons with • This machine does not stay upright
reduced physical, sensory or mental without constant support. Between
capabilities, or lack of experience or uses, lie flat on the floor in a suitable
knowledge, unless they have been location so that it does not become a
given instructions concerning the trip hazard or can be stepped on.
safe use of the machine by a person
legally responsible for their safety. BATTERY SAFETY PRECAUTIONS
They should be supervised whilst • Replace the battery with a VAX
using the machine. Children shall not ONEPWR battery only. Use of
use, clean or play with this machine, another battery may present a risk
which when not in use should be of fire or explosion.
secured out of their reach. • Do not attempt to disassemble the
• Keep fingers, hair and loose clothing battery, remove any component
away from moving parts and projecting from the battery terminals
openings whilst using the machine. and do not dispose of in a fire.
• Store the machine in a cool, dry The battery and charger have no
area. Keep the machine away from user serviceable parts. Fire or injury
rain and moisture. may result.
• Use only CE approved 13amp • Prior to disposal, protect exposed
extension cords, non-approved terminals with heavy insulating tape
extension cords may overheat. to prevent shorting. The battery is to
Care should be taken to arrange the be disposed of safely at your local
extension cord as it can be a trip battery recycling centre.
hazard. • When the battery pack is not in
• Take extra care when using the use, keep it away from other metal
machine on the stairs. objects that can make a connection
• Always turn the powered floorhead from one terminal to another.
brushbar off when cleaning hard Shorting the battery terminals
floors. To prevent any damage being together may cause burns or a fire.
sustained, test on an inconspicuous • In case of battery leakages, avoid
area of the flooring first. any contact with skin and contact us
• Always make sure the separator on: 08000 927737.
and filter are fitted correctly before
using your machine and only use the
machine with the filter and separator
in place.
WARRANTY & TECHNICAL support.vax.co.uk 4

WARRANTY
If a VAX ONEPWR machine is used • Faults caused by:
in the way it is intended and it breaks - Negligent use, misuse, neglect or
down within the guarantee period, it’s careless operation of the machine.
our responsibility to repair or replace it. - Use of the machine cleaner which
Here’s what isn’t covered: is not in accordance with the
• Normal wear and tear of consumable user guide.
items, for example: belts, filters, - Use of a VAX ONEPWR machine
brushbars, fuses etc. for anything other than normal
• Batteries which have become faulty domestic household purposes
as a result of improper handling. in the country in which it was
• Batteries which have a reduced purchased.
service life as a result of normal wear. - Use of parts, accessories and
• Accidental damage consumables, which are not
- Damage as a result of use not in genuine VAX components.
accordance with the product - Faulty installation or repairs –
user guide. unless carried out by a qualified
- Damage caused by not carrying out electrician or engineer. 
regular maintenance.
- Damage to the charger cable.
- Blockages caused by misuse.

TECHNICAL
EU Statement of Compliance: Manufacturer/EU importer: VAX Limited, hereby on
our own responsibility, declare that the VAX ONEPWR Blade 4 is manufactured in
compliance with the following Directives:
Safety: 2014/35/EU Low Voltage Directive.
EMC: 2014/30/EU Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.

VAX is a trade mark of Techtronic Cordless GP.

© 2020 Techtronic Cordless GP. All rights reserved.

VAX Ltd, Artillery House, Heritage Way, Droitwich, WR9 8YB, UK.
GETTING TO KNOW YOUR MACHINE support.vax.co.uk 5
1 Carry handle
6
2 Dirt container
3 Filter cover and filter
7 4 Dirt container release latch
1
8 5 Dirt release button
6 Power ON/OFF
9
7 Brushbar ON/OFF
2 8 Boost ON/OFF
9 Battery level indicator light
3 10 Reach wand
11 Powered floorhead

4 12 Brushbar
13 13 Battery dock
5 14 Filter cover release tab
14 (hidden)
15 ONEPWR Battery*
16 ONEPWR Charger*
17 Crevice tool
18 Dusting brush
19 Crevice tool storage caddy
20 Wall mount
screws and wall plugs
10

15 16

17 18 19 20

TECHNICAL SPECIFICATION
VAX ONEPWR Blade 4
Weight (without battery pack) 2.8kg
Dirt bin capacity 0.6L
11
Runtime and charge time dependent on battery pack
12 and power mode used.
*Included with model CLSV-B4KS only.
Subject to technical change without notice. Images are illustrative only.
GETTING STARTED support.vax.co.uk 6

ASSEMBLY

To assemble the dirt container, line up the arrow on the dirt Attach the handheld to the reach wand until it clicks into place.
container connection with the arrow on the handle. Push the Attach the reach wand to the powered floorhead until it clicks
dirt container onto the handle until it clicks into place. into place. Push the tool caddy onto the reach wand and slot the
crevice tool into place.

ATTACHING THE WALL MOUNT

Without the handheld attached to the Choose a location for the machine to be stored, preferably near to a mains supply
reach wand and powered floorhead, although not directly above or below a mains socket. Stand the machine powered
push the wall bracket onto the top and floorhead and wand against the wall, ensuring the powered floorhead is flat on
back of the reach wand. the floor.

Holding the wall bracket securely against The dusting brush can be fitted onto the Fully assemble the machine and firmly
the wall, make a small mark for each wall bracket. press the machine into the wall bracket
screw. Secure the wall bracket to the to secure. Always ensure the machine is
wall using the wall plugs and screws. securely locked into place.
GETTING STARTED support.vax.co.uk 7

CHARGING THE BATTERY

THIS MACHINE IS ONLY TO BE USED WITH VAX ONEPWR BATTERIES AND CHARGER.
PLEASE READ THE SAFETY GUIDE BEFORE USE.

NOTE: Before first use, ensure the battery is fully charged. Failure to fully charge the battery
before first use may result in poor battery performance. The life expectancy of the battery will vary
depending on the usage of the machine.

Slide the battery down on to the charger. The charger light will flash white to Once fully charged, slide the battery off
show when the battery is charging. the charger to remove.
The light on the charger will stop
flashing and go off when the battery To check the battery charge
is fully charged. level press the battery symbol.

OPERATION

WARNING: The brushbar in the powered floorhead constantly rotates when switched on. Never use
the powered floorhead on one spot for an extended period of time as the brushbar may damage the
floor surface. Always turn the powered floorhead brushbar off when cleaning hard floors. To prevent
any damage being sustained, test on an inconspicuous area of the flooring first.

Slide the battery into the handheld until Place your foot on the powered floorhead. To remove the battery press both the
it clicks into place. Pull the handle backwards to recline. buttons to release.
GETTING STARTED support.vax.co.uk 8

OPERATION

Press the on/off button to switch the Press the brushbar on/off button to Press the boost button on to increase
machine on. switch the brushbar on. the suction for particularly dirty areas.

NOTE: The powered floorhead brushbar should be ON for carpets and OFF for hard floors.
Constant use of the boost mode and brushbar will reduce the battery runtime.

When the machine is in use the battery All of the accessories, including the
level indicator lights will illuminate powered floorhead can be attached
indicating how much charge is directly onto the handheld or the reach
remaining. When less than 20% charge wand. The crevice tool and dusting
is remaining the bottom light will flash brush can be used for hard to reach
red indicating the battery is running low places and at different heights for above
and charging is required. floor cleaning.

CAUTION: If the brushbar in the powered floorhead has been

obstructed, the brushbar motor protection sensor may have been
activated. The brushbar will stop, the light on the powered floorhead
will illuminate red and the machine may switch off. To reset remove
the powered floorhead from the reach wand/handheld and clear any
obstruction. Wait 1 minute before refitting the powered floorhead tool,
switch the machine on and press the brushbar ON/OFF button.
CLEANING & MAINTENANCE support.vax.co.uk 9

REMOVING AND REFITTING THE DIRT CONTAINER

WARNING: Always remove the battery before carrying out any maintenance or troubleshooting.

1. Squeeze the latch on the dirt To refit, line up the dirt container When correctly fitted all 3 connection
container to release. connection with the handheld handle. points will be aligned and will sit flush.
2. Tilt and lift to remove from the Push the dirt container back onto the
handheld. handle until it clicks into place.

EMPTYING THE DIRT CONTAINER

CAUTION: Don’t over fill the dirt container to avoid blocking the air flow through the machine.
For best cleaning results, empty the dirt container after every use. Filters should be tapped over a
bin every 4-6 uses to remove dirt and debris and washed every 3 months. Filters should be replaced
every 6-9 months depending on the level of use.

1. Squeeze the latch on the dirt Hold the dirt container over a bin and To close, push the dirt release door until
container to release. press the dirt release button to allow dirt it clicks into place.
2. Tilt and lift to remove from the and debris to fall out.
handheld.
CLEANING & MAINTENANCE support.vax.co.uk 10

CLEANING THE FILTER AND SEPARATOR

Push the tab on the lid of the dirt container and lift the cover to access the filter. Lift the filter and separator from the
dirt container.

Tap the separator over a bin to remove Pull the tab on the filter to remove from Tap the filter against the bin to remove
dirt and debris and wipe over the metal the separator. any dirt and debris.
shroud with a dry cloth.

CAUTION: Ensure both

the filter and separator are
refitted before use.

40°C
MAX
24hr

Wash the filter under running water

(40°C max). Leave for at least 24hrs or
until fully dry before replacing.
CLEANING & MAINTENANCE support.vax.co.uk 11

CLEANING AND REPLACING THE POWERED FLOORHEAD BRUSHBAR

Press the floorhead release button to Using a coin, push and turn the brushbar lock anticlockwise to release the brushbar.
remove the floorhead from the machine.

Pull the brushbar out from the brushbar To remove any threads or hair, slide Clear any dirt/debris from the end caps
housing. the blade of a pair of scissors into the and inside the housing of the powered
groove on the brushbar and cut along floorhead.
the groove.

Refit the brushbar into the floorhead. Align the arrow on the brushbar cover so it
points north, firmly push and twist clockwise to lock.
CLEANING & MAINTENANCE support.vax.co.uk 12
CHECKING FOR BLOCKAGES

Press the handheld release button and Press the dirt container release button Check the powered floorhead for any
remove the reach wand. Check and clear and remove the dirt container. Check blockages and use a blunt object to
any dirt and debris from the handheld and clear any dirt and debris from remove the blockage.
connection point. behind the dirt container flap.

To test for a blockage in the reach wand,

drop a small ball of paper into the wand.
The paper will drop through if the wand
is clear. Use a broom handle or similar
blunt object to remove any blockage.
TROUBLESHOOTING support.vax.co.uk 13
THERE IS AN ACCESSORY MISSING
Check the contents on the back of the box.
WHY DOES THE MACHINE HAVE NO POWER?
• The battery is not fitted correctly. See OPERATION page 7.
• The battery has no charge. See CHARGING THE BATTERY page 7.
• The motor thermostat may have tripped. Empty the dirt container and check for blockages.
Clean the filters and allow the machine to cool for approximately 1 hour. If you have washed
the filters, wait 24 hours to fully dry before placing back on the machine.
See CLEANING THE FILTER AND SEPARATOR page 10.
• The brushbar motor sensor has been activated. To reset remove the powered floorhead from
the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting the powered
floorhead, switch the machine on and press the brushbar ON/OFF button. See OPERATION
page 8.
WHY WON’T THE MACHINE PICK UP?
• The dirt container may not be correctly fitted. See REMOVING AND REFITTING THE DIRT
CONTAINER page 9.
• The dirt container may be blocked. Check the dirt container and handheld inlet for blockages.
See EMPTYING THE DIRT CONTAINER page 9.
• The filters may be clogged. See CLEANING THE FILTER AND SEPARATOR page 10.
• There maybe a blockage. See CHECKING FOR BLOCKAGES page 12.
• The brushbar on the powered floorhead has not been activated. See OPERATION page 8.
• The powered floorhead may be blocked. See CLEANING AND REPLACING THE POWERED
HEAD BRUSHBAR page 11.
• The machine, powered floorhead and reach wand may not be correctly fitted.
See ASSEMBLY page 6.
WHY IS THERE A RED LIGHT?
• Battery charge is running low (<20%). See CHARGING THE BATTERY page 8.
WHY IS THERE A RED LIGHT ON THE POWERED FLOORHEAD?
• The powered floorhead brushbar has been obstructed. See CLEANING AND REPLACING THE
POWERED FLOORHEAD BRUSHBAR page 11.
WHY WON’T THE BRUSHBAR TURN?
• The brushbar on the powered floorhead has not been activated. Go to OPERATION page 8.
• The tool/brushbar may be obstructed. See CLEANING AND REPLACING THE POWERED
HEAD BRUSHBAR page 11.
• The machine, powered floorhead and reach wand may not be correctly fitted. See ASSEMBLY
page 6.