MasterKure® 106

Water based concrete curing compound / bond breaker

DESCRIPTION STANDARDS
MasterKure 106 is a solvent free, membrane ASTM C309 Type 1 Class A
forming wax emulsion, suitable for spray AASHTO M-148 Type 1 Class A
application to freshly poured concrete.
DIRECTIONS FOR USE AS A CURING
The resultant film retains sufficient moisture in the COMPOUND
concrete to ensure full hydration of the cement; The compound should be spray applied as evenly
essential for optimum strength development. as possible on to the freshly placed concrete.
Membrane cured concrete is typically harder and
exhibits a dust free surface with a reduced For horizontal surfaces MasterKure 106 should be
incidence of drying shrinkage cracks. applied as soon as the initial surface sheen has
disappeared from the concrete surface. In the
The film can also act as a bond breaker between case of formed concrete, the MasterKure 106
initial and subsequent concrete pours. should be applied immediately on removal of the
formwork. To assist breakdown of the
PRIMARY USES MasterKure 106 film on vertical and formed
As a more effective and economical alternative to surfaces, it is essential to dampen down the
hessian and water and polythene curing regimes. concrete with clean water prior to application.
Suitable for use on all concrete surfaces.
As a bond breaking film for the vertical face of DIRECTIONS FOR USE AS A BOND
precast bridge segments during match casting. BREAKER
The compound should be spray applied to form an
ADVANTAGES even film covering the entire surface against which
 Eliminates the need for water. the subsequent segment will be cast.
 Single application. If necessary, more than one coat should be
 Promotes a harder dust free surface. applied. The actual coverage and number of coats
 Cured film is clear and water repellent. will be dependent on texture and porosity of the
 Reduces drying shrinkage. surface. The recommended application rate when
 High curing efficiency. used as a bond breaker is 4 square meters per
 Reduced labour costs. litre.
 Water based.
COVERAGE
PACKAGING The recommended rate of application is 5-6
square metres per litre. This corresponds to that
MasterKure 106 is available in 210 litre drums.
at which MasterKure 106 has been tested, and at
which it attains the claimed degree of curing
TYPICAL PROPERTIES* efficiency. In favourable conditions such as
shaded interior surfaces, adequate curing can be
Appearance White liquid achieved with extended coverage rates.
Specific gravity 1.00
Flashpoint Not applicable
Finished film appearance Clear, tack free, water
repellent film
Water retention ASTM C156 Pass
Drying time ASTM C309 Less than 4 hours
MasterKure® 106
FILM BREAKDOWN STORAGE
The time for deterioration of the membrane is Shelf life is up to 12 months when stored under
dependent on a number of variables, which cover, out of direct sunlight and protected from
include film thickness, degree of exposure to extremes of temperature.
weathering, traffic, UV light, and the porosity of the
substrate concrete. HEALTH AND SAFETY
As with all chemical products, care should be
SUBSEQUENT SURFACE FINISHES taken during use and storage to avoid contact with
It is important that the complete removal of the eyes, mouth, skin and foodstuffs. Treat splashes
MasterKure 106 should be ensured prior to the to eyes and skin immediately. If accidentally
application of any surface finish or additional ingested, seek medical attention. Reseal
treatment. It is recommended that where the containers after use. Use in well ventilated areas
concrete is to receive a coating or the application and avoid inhalation.
of tiles, the use of MasterKure 181 is considered.
NOTE
MasterKure 181 is a resin based non-degrading Field service, where provided, does not constitute
curing membrane meeting the requirements of supervisory responsibility. For additional
ASTM C-309 Type 1 Class B. It is additionally information contact your local BASF
formulated to act as a primer for many finishes or representative.
to seal concrete surfaces and provide a degree of
abrasion to flatwork. BASF reserves the right to have the true cause of
any difficulty determined by accepted test
SPECIFICATION CLAUSE methods.
Where indicated, concrete shall be cured by
application of MasterKure 106, membrane QUALITY AND CARE
forming wax emulsion manufactured by BASF or All products originating from BASF’s Dubai, UAE
similar approved; to the following specification: facility are manufactured under a management
Specification type: system independently certified to conform to the
ASTM C309: Type 1 Class A requirements of the quality, environmental and
AASHTO M-148 occupational health & safety standards ISO 9001,
MasterKure 106 is to be applied at a coverage ISO 14001 and OHSAS 18001.
rate of 5 to 6 square metres per litre and strictly in
accordance with the manufacturer’s instructions.
* Properties listed are based on laboratory controlled tests.

® = Registered trademark of the BASF-Group in many countries.

BASF_CC-UAE/Kure_106_05_95/v2/02_17
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.

BASF Construction Chemicals UAE LLC Disclaimer: the LRQA mark relates
P.O. Box 37127, Dubai, UAE to certified management system and
Tel: +971 4 8090800, Fax: +971 4 8851002 not to the product mentioned on this
www.master-builders-solutions.basf.ae datasheet