PROGRAMMABLE UNITARY CONTROLLER

PUC SERIES IO EXTENSION MODULE

PRODUCT DATA

OVERVIEW
• Built-in input/output ports allowing extension module through
PUC I/O extension modules are part of the RS-485 port to enrich point combination
Honeywell PUC Series programmable unitary • Support the connection of points among controllers, namely
controller which supports Ethernet BACNet IP “binding”, to make invocation more convenient
communication. Two types of I/O modules extend the
• Additional network security with advanced security encryption
functions of the controller and meet the need of more
standard
I/O points. The hardware design of the controller
integrates with the elements of Honeywell's user • Embedded programmable tool under niagara platform with
user friendly interface, compatibly use the programs edited by
experience, which embodies the essence of people-
the existing WEBs tools
oriented concept no matter from appearance or
usage. I/O extension modules, integrated with the • CE, UL and RoHS certification
controller, is programmable by using the same
programming tools and can be widely used to control
different building equipment. TECHNICAL SPECIFICATION
Description
FEATURES TABLE 1 ORDERING PART NUMBER

• Work with PUC controller to monitor more equipment PART NUMBER DESCRIPTION

• Fully programmable on the PUC controller via IO extension module

PUC5533-EM2
programming tools to meet different HAVC UIx5, DIx5, AOx3, DOx3
applications IO extension module UIx6,
PUC6002-EM2
• Enable I/O modules to be connected to the controller DOx2
by RS-485 Bus
ELECTRICAL
• Up to 2 extension modules can be connected to
a single controller Nominal voltage: 20-30 VAC; 50/60 Hz

• Elegant design, light weight and easy to operate, POWER CONSUMPTION: PUC5533-EM2 11 VA max.

which continues Honeywell's style on the unitary (including controller
controller and all input, output and
communication channels)
• Color-coded removable terminal blocks for
differentiating signal types enable convenient and PUC6002-EM2 7 VA max.
(including controller
fault free termination
and all input, output and
communication channels)
OPERATING ENVIRONMENT ANALOG OUTPUT (AO)

• Operating temperature 0°C - +50°C The analog outputs must be current or voltage signals at
the same time.
• Relative humidity: 5%~95% Non-condensating
Analog current output:
• Protection rating IP20
• Current output: 4-20 mA
• Maximum output load resistance: 550 Ohms
SIZE (H/W/D) Analog voltage output:
• Voltage output: 0-10 VDC
• 180 x 115 x 57.5 mm
• Maximum output current: 10 mA
Analog output can be defined as digital output and run
CERTIFICATION as follows:

• CE • False (0%) output 0 VDC, (0 mA)

• True (100%) maximum output 11 VDC, (22 mA)
• UL
• RoHS
UNIVERSAL INPUT (UI) DETAILS ARE
SHOWN IN TABLE 2
INPUT AND OUTPUT
TABLE 2 UNIVERSAL INPUT DETAILS
DIGITAL INPUT (DI)
INPUT TYPE SENSOR Operating Range
• Input type: Supervised dry contact ON/OFF Outdoor
temperature
• Resistance: open circuit ≥ 12K Ohms; 20K Ohm NTC -40°C to 93°C
for room/area
 circuit ≤ 500 Ohms
 
closed air supply
 Outdoor PT1000
DIGITAL OUTPUT (DO) -40°C to 93°C
temperature (IEC751 3850)

 
• Nominal voltage: 20-30 VAC, 50-60Hz 100 Ohms-
Input resistance Normal
100K Ohms

 
• Rated current: 0 mA-1A(AC), continuous
Transmitter
1A Pilot Duty Input voltage 0-10 VDC
Controller
 Open circuit ≥12K
Digital input Dry contract Ohms Closed circuit
≤ 500 Ohms

 
Accuracy of digital/analog conversion: 12 bit

COMMUNICATION INTERFACE

• 485 Bus: 1 RS485 port, connected with the main

controller, supporting up to two IO extension modules,
and 18-22AWG shielded twisted pair cable are
recommended for use.
LED DISPLAY TABLE 4 485 LED STATUS DESCRIPTION

Controller's status can be displayed via LED. RS485 communication status

485 LED STATUS CONTROLLER STATUS

TABLE 3 STA LED STATUS DESCRIPTION
Equipment fault or
STA LED STATUS CONTROLLER STATUS Solid on
system crashed
No power; damaged No power supply or equipment
LED; insufficient power Solid Off
Off malfunction or system crashed
supply; initial power-on;
or boot loader damaged Solid off, blink once Controller is operating
every 2.5 sec normally without Modbus
Start up power insufficient;
communication
check power supply – this
Solid on requires about 3.5 sec – Solid off, blink twice Controller is operating normally
occurs on power up, reset every 2.5 sec with Modbus communication
and refresh Solid off, blink three Controller is operating with
Blinking mode 1 – times every 2.5 sec applications downloading
continuously blinks on Operating normally Rapid blinking Equipment fault or
for 1 sec and off for 1 sec system crashed
Equipment alarm
Blinking mode 2 –
active; downloading
continuously blinks on for Pollution level: level 2
configuration; loss of
0.5 sec and off for 0.5 sec Electric shock protection level: Class II
configuration
The distance among contact heads: micro-gap
DIP SWITCH (BINARY ENCODING) Load-type: continuous
The connection of input/output: use screw
The DIP switch is pulled up to "ON". clamp terminals
Dip Switch Numbers 1-5, corresponding to low Installation: DIN-rail EN50022
order to high order, are used to set address

1 2 4 18 16 Baud rate
Address

ON

Dip Switch Numbers 6-7 are used to adjust Baud rate

(the default value is 38400)

DIP SWITCH DIP SWITCH

Baud rate
NUMBER6 NUMBER7
Off Off 38400
On Off 19200
Off On 9600
On On 4800
PRODUCT DIMENSIONS (UNIT: mm)

PRODUCT INSTALLATION

INSTALLATION NOTES

• Removable terminals make it easier for

installation and maintenance;
• Controller must be installed in adequate
space for wiring, maintenance and removal;
• Product supports DIN rail.
DIN rail specification: EN50022
7.5 mm x 35 mm.

INSTRUCTIONS:

1. Pull both hooks at the base of the

controller. Tilt the controller and fix the
hooks on the top of the controller onto the
guide rail;
2. Press the controller for it to fit the guide rail;
3. Push in both hooks at the base to fasten
the controller;
4. The controller after the hooks are pushed
in is as shown in Figure 4.

Honeywell Environmental and

Combustion Controls (Tianjin) Co., Ltd.
No. 158, Nanhai Road, Tianjin
Economic-Technological Development Area
Postal Code: 300457
Tel: +86-22-66287000
Fax: +86-22-25325214 HBT-Building-BCS-WEBs-Oct.2019 –EN01