Inspection and Quality Control in Manufacturing ... https://onlinecourses-archive.nptel.ac.in/noc19...

[email protected] ▼

Courses » Inspection and Quality Control in Manufacturing

Announcements Course Ask a Question Progress FAQ

Unit 2 - Week 1
Register for
Certification exam Assignment 1
The due date for submitting this assignment has passed.
Course As per our records you have not submitted this Due on 2019-03-13, 23:59 IST.
outline
assignment.

How to access 1) Which of the following quality gurus defined the “quality” as “Quality is conformance to 1 point
the portal requirements”?

Week 1 Joseph Juran

Introduction: Philip Crosby

Fundamental
Feigenbaum
concepts of
quality, Edwar Demning
inspection and
their role in No, the answer is incorrect.
manufacturing Score: 0
Need of Accepted Answers:
Inspection: Philip Crosby
Types and
Principles 2) What is the effect on the perceived quality, when customers’ expectations of a product are 1 point
Destructive
equal to customer’s perceptions?
Inspection-I
Perceived quality is good
Destructive
Inspection-II Perceived quality is poor

Testing of Perceived quality is acceptable

Composite
Perceived quality is not acceptable
Materials

Quiz : No, the answer is incorrect.

Assignment 1 Score: 0

Solution for Accepted Answers:

Assignment 1 Perceived quality is acceptable

Week 2 3) Which of the following are the correct attributes to define quality control of a product when 1 point
viewed as a system?
Week 3
Proper equipment
Week 4 Right design

© 2014 NPTEL - Privacy & Terms - Honor Code - FAQs -

A project of In association with

Funded by

1 of 5 Thursday 20 June 2019 01:53 PM

Inspection and Quality Control in Manufacturing ... https://onlinecourses-archive.nptel.ac.in/noc19...

All of these Powered by

4) A decision on the acceptance or rejection of a lot in the double sampling plan is made on 1 point
the basis of how many samples?

Two

Three

One

Multiple

No, the answer is incorrect.

Score: 0
Accepted Answers:
Two

5) “Radiography testing” is an example of which type of inspection? 1 point

Centralized Inspection

Contact Inspection

Non-contact Inspection

Combined Inspection

No, the answer is incorrect.

Score: 0
Accepted Answers:
Non-contact Inspection

6) Which type of inspection does this picture depict? 1 point

Floor Inspection

On-line/In-process Inspection

On-line/Post-process Inspection

Centralized Inspection

No, the answer is incorrect.

Score: 0
Accepted Answers:
On-line/In-process Inspection

7) Which of the following statements is/are true regarding the destructive inspection 1 point
techniques:

These tests are used to determine the service life of a component under given loading
condition.

They are most suitable and economical for mass production.

They are used to determine chemical, mechanical and metallurgical properties.

All of these.

No, the answer is incorrect.

Score: 0
Accepted Answers:
All of these.

8) A cylindrical specimen of copper having an original diameter of 15.2 mm is pulled in tension 1 point
with 9,500 N force, producing only elastic deformation. What is the resulting engineering stress in the
specimen?

2 of 5 Thursday 20 June 2019 01:53 PM

Inspection and Quality Control in Manufacturing ... https://onlinecourses-archive.nptel.ac.in/noc19...

52 MPa

20 MPa

104 MPa

13 MPa

No, the answer is incorrect.

Score: 0
Accepted Answers:
52 MPa

9) Why etching is done in metallographic tests? 1 point

To reveal the microstructure of a specimen under the optical microscope by achieving

contrast in the microstructure.

To remove the deformations from grinding and obtain a surface that is highly reflective.

To determine the type and rate of corrosion.

All of these.

No, the answer is incorrect.

Score: 0
Accepted Answers:
To reveal the microstructure of a specimen under the optical microscope by achieving contrast in the
microstructure.

10)The initial minor loads for the Rockwell hardness test and Rockwell superficial hardness 1 point
test, respectively, are:

7 Kg and 1 Kg

1 Kg and 7 Kg

10 Kg and 3 Kg

3 Kg and 10 Kg

No, the answer is incorrect.

Score: 0
Accepted Answers:
10 Kg and 3 Kg

11)How the specimen is positioned in Charpy impact test? 1 point

Cantilever beam

Simply supported beam

Fixed beam

All of these

No, the answer is incorrect.

Score: 0
Accepted Answers:
Simply supported beam

12)The resistance to fatigue of a material is measured by: 1 point

Young’s modulus

Ultimate tensile strength

Elastic limit

Endurance limit

3 of 5 Thursday 20 June 2019 01:53 PM

Inspection and Quality Control in Manufacturing ... https://onlinecourses-archive.nptel.ac.in/noc19...

No, the answer is incorrect.

Score: 0
Accepted Answers:
Endurance limit

13)What is a cermet? 1 point

Composite material composed of cellulose fibers held together by lignin matrix.

Composite material composed of collagen fibers embedded in hydroxyapatite matrix.

Composite material composed of ceramic and metal materials.

All of these.

No, the answer is incorrect.

Score: 0
Accepted Answers:
Composite material composed of ceramic and metal materials.

14)Which of the following is the correct formula for calculating the moisture content (by wt. %) 1 point
present in a material?
Consider the notations used as: M, % = Percentage moisture content
Wi = Initial specimen mass
Wo = Oven-dry specimen mass

No, the answer is incorrect.

Score: 0
Accepted Answers:

15)Which of the following test method(s) is/are used to understand the mechanical behaviour 1 point
of composite materials?

Fiber pull-out tests

Fragmentations tests

Indentation tests

All of these

No, the answer is incorrect.

Score: 0
Accepted Answers:
All of these

Previous Page End

4 of 5 Thursday 20 June 2019 01:53 PM

Inspection and Quality Control in Manufacturing ... https://onlinecourses-archive.nptel.ac.in/noc19...

5 of 5 Thursday 20 June 2019 01:53 PM