A780L3C Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents

here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.

Dichiarazione di conformità Short Declaration of conformity

sintetica We declare this product is complying
Ai sensi dell’art. 2 comma 3 del D.M. with the laws in force and meeting all
275 del 30/10/2002 the essential requirements as specified
Si dichiara che questo prodotto è by the directives
conforme alle normative vigenti e 2004/108/CE, 2006/95/CE and
soddisfa i requisiti essenziali richiesti 1999/05/CE
dalle direttive whenever these laws may be applied
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
 Table of Contents

Chapter 1: Introduction.......................................... 3
1.1 Before You Start ................................................................................3
1.2 Package Checklist ............................................................................3
1.3 Motherboard Specifications .............................................................4
1.4 Rear Panel Connectors....................................................................5
1.5 Motherboard Layout..........................................................................6
Chapter 2: Hardware Installation ........................... 7
2.1 Install Central Processing Unit (CPU)............................................7
2.2 Install a Heatsink ...............................................................................8
2.3 Connect Cooling Fans......................................................................9
2.4 Installing System Memory..............................................................10
2.5 Expansion Slots...............................................................................12
2.6 Jumper Setting ................................................................................13
2.7 Headers & Connectors ...................................................................14
Chapter 3: BIOS & Software ................................. 18
3.1 BIOS Setup ......................................................................................18
3.2 BIOS Update....................................................................................18
3.3 Software............................................................................................23
Chapter 4: Useful Help ......................................... 26
4.1 Driver Installation.............................................................................26
4.2 Troubleshooting...............................................................................27
4.3 RAID Functions ...............................................................................29
Appendix: Specifications In Other Languages ...... 32
German .................................................................................................................32
French ...................................................................................................................34
Italian .....................................................................................................................36
Spanish..................................................................................................................38
Portuguese ...........................................................................................................40
Polish .....................................................................................................................42
Russian .................................................................................................................44
Arabic.....................................................................................................................46
Japanese...............................................................................................................48
 A780L3C

CHAPTER 1: INTRODUCTION
1.1 Before You Start
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„ Prepare a dry and stable working environment with sufficient
lighting.
„ Always disconnect the computer from power outlet before
operation.
„ Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
„ Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
„ Do not leave any unfastened small parts inside the case after
installation. Loose parts will cause short circuits which may
damage the equipment.
„ Keep the computer from dangerous area, such as heat
source, humid air and water.
„ The operating temperatures of the computer should be 0 to
45 degrees Celsius.
„ To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit

1.2 Package Checklist

; Serial ATA Cable x2
; Rear I/O Panel for ATX Case x1
; Installation Guide x1
; Fully Setup Driver DVD x1
Note: The package contents may be different due to the sales region or models in which it was sold.
For more information about the standard package in your region, please contact your dealer or sales
representative.

3
Motherboard Manual

1.3 Motherboard Specifications

SPEC

Socket AM3
AMD 64 Architecture enables 32 and 64 bit computing
CPU AMD Sempron / Phenom II / Athlon II processors
Supports Hyper Transport 2.0
(Maximum Watt: 95W)

Support Hyper Transport 3.0

FSB
Supports up to 3.2 GT/s Bandwidth

AMD 760G
Chipset
AMD SB710

Low Pin Count Interface

ITE 8728F-BX
Environment Control initiatives
Super I/O Provides the most commonly used legacy Super
H/W Monitor
I/O functionality
ITE's "Smart Guardian" function

DDR3 DIMM Slots x 2

Dual Channel Mode DDR3 memory module
Main Max Memory Capacity 16GB
Supports DDR3 800/1066/1333/1600(OC)
Memory Each DIMM supports 512MB/1GB/
Registered DIMM and ECC DIMM is not supported
2GB/4GB/8GB DDR3

Graphics Integrated in AMD 760G Chipset Max Shared Video Memory is 1024MB

Data transfer rates up to 3 Gb/s

SATA II Integrated Serial ATA Controller
SATA Version 2.0 specification compliant

LAN Realtek RTL 8105T 10 / 100 Mb/s auto negotiation

5.1 channels audio out

Sound VT1708B / ALC662
High Definition Audio

PCI Express X16 slot x1 Supports PCI-E X16 expansion card

Slots
PCI slot x1 Supports PCI expansion cards

On Board SATA Connector x4 Each connector supports 1 SATA device

Connectors
IDE Connector x1 Each connector supports 2 IDE device

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

4
 A780L3C
SPEC

System Fan Header x1 System Fan Power supply

CMOS Clear Jumper x1 Restore CMOS data to factory default setting

USB Connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

PS/2 Keyboard x1 Connects to PS/2 Keyboard

PS/2 Mouse x1 Connects to PS/2 Mouse

Back Panel VGA port x1 Connect to D-SUB monitor

I/O LAN port x1 Connect to RJ-45 Ethernet cable

USB Port x4 Connect to USB devices

Audio Jack x3 Provide Audio-In/Out and microphone connection

Board Size 182 mm(W) x 225 mm(L)

Special
RAID 0 / 1 / 10 support
Features

Biostar reserves the right to add or remove support for any

OS Support Windows XP / Vista / 7 / 8
OS With or without notice.

1.4 Rear Panel Connectors

5
Motherboard Manual
1.5 Motherboard Layout

Note: ■ represents the 1st pin.

6
 A780L3C

CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)
Step 1: Locate the CPU socket on the motherboard

Step 2: Pull the socket locking out from the socket and then raise the lever up to a
90-degree angel.

Step 3: Look for the white triangle on socket, and the gold triangle on CPU should
point towards this white triangle. The CPU will fit only in the correct
orientation.

182m(幅
)X25m(高
さ
)
to prevent damaging the CPU.

7
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever to locked the position

2.2 Install a Heatsink

Step 1: Place the heatsink and fan assembly onto the retention frame. Match the
heatsink clip with the socket mounting-lug. Hook the spring clip to the
mounting-lug.

Step 2: On the other side, push the retention clip straight down to lock into the
plastic lug on the retention frame, and then press down the locker until it
stops.

Note1: Do not forget to connect the CPU fan connector.

Note2: For proper installation, please kindly refer to the installation manual of your CPU
heatsink.

8
 A780L3C
2.3 Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different according to the fan manufacturer. Connect the fan
cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control
(By Fan)

SYS_FAN1: System Fan Header

Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense

Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be connected to pin#2, and the black wire is Ground and should be connected to
GND.

9
Motherboard Manual
2.4 Installing System Memory
A. DDR3 Memory Modules

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM
on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip snap
back in place and the DIMM is properly seated.

Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

10
 A780L3C

B. Memory Capacity
DIMM Socket Total Memory
DDR3 Module
Location Size
DDR3_A1 512MB/1GB/2GB/4GB/8GB
Max is 16GB.
DDR3_B1 512MB/1GB/2GB/4GB/8GB

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DDR3_A1 DDR3_B1
Disabled O X
Disabled X O
Enabled O O
(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or x16)

11
Motherboard Manual

2.5 Expansion Slots

PEX16_1: PCI-Express X16 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

PCI1: Peripheral Component Interconnect Slot

This motherboard is equipped with 1 standard PCI slot. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

12
 A780L3C

2.6 Jumper Setting

The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin1-2 closed

JCMOS1: Clear CMOS Jumper

Placing the jumper on pin2-3 allows user to restore BIOS safe setting and
CMOS data. Pease carefully follow the procedures to avoid damaging the
motherboard.

1 3

Pin 1-2 Close:

Normal Operation
(default).

1 3

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS.

13
Motherboard Manual

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

Pin Assignment
1 +12V
2 +12V
3 Ground
4 Ground

Note1: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connectors have been plugged-in.
Note2: Insufficient power supplied to the system may result in instability or the peripherals
not functioning properly. Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices.

14
 A780L3C

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
N/A
2 N/A Speaker 10 N/A
3 N/A Connector 11 N/A N/A
4 Speaker 12 Power LED (+)
5 HDD LED (+) Hard drive 13 Power LED (+) Power LED
6 HDD LED (-) LED 14 Power LED (-)
7 Ground 15 Power button
Reset button Power-on button
8 Reset control 16 Ground

SATA1~SATA4: Serial ATA Connectors

These connectors connect to SATA hard disk drives via SATA cables. It satisfies
the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment
1 Ground
2 TX+
3 TX-
4 Ground
5 RX-
6 RX+
7 Ground

15
Motherboard Manual

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode
0~4, Bus Master, Multi-word DMA, and Ultra DMA 33/66/100/133 functionality.

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
9 NC
10 Key

16
 A780L3C

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in
10 Jack Sense

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

17
Motherboard Manual

CHAPTER 3: BIOS & SOFTWARE

3.1 BIOS Setup
„ For better system performance, the BIOS firmware is being continuously
updated. The BIOS information described below in this manual is for your
reference only and the actual BIOS information and settings on board may
be different from this manual
„ For further information of setting up the BIOS, please refer to the BIOS
Manual in the Setup DVD.

3.2 BIOS Update

There are three ways to update the BIOS:
BIOS Update Utility, BIOS Online Update Utility and BIOS Flasher.

1. BIOS Update Utility

1. Installing BIOS Update Utility from the DVD Driver.
2. Download the proper BIOS from www.biostar.com.tw .

Show current BIOS information

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Save current BIOS

to a .bin file

Update BIOS
with a BIOS file

18
 A780L3C

<Backup BIOS>

Once click on this button, the saving

dialog will show. Choose the position to
save file and enter file name. (We
recommend that the file name should be
English/number and no longer than 7
characters.) Then click Save.

After the saving process, finish dialog

will show. Click on OK to complete the
BIOS Backup procedure.

<Update BIOS>
Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS

procedure should be run with Clear
CMOS function, so please check on
Clear CMOS first.

Then click Update BIOS button, a

dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the

open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

19
Motherboard Manual

The utility will update BIOS with the

proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on

OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

2. Online Update Utility

1. Installing BIOS Update Utility from the DVD Driver.
2. Please make sure the system is connected to the internet before using this
function.

3. Open BIOS Update Utility and

click the Online Update button
on the main screen.

4. An open dialog will show up to

request your agreement to
start the BIOS update. Click
Yes to start the online update
procedure.

20
 A780L3C

5. If there is a new BIOS version,

the utility will ask you to
download it. Click Yes to
proceed.

6. After the download is

completed, you will be asked
to program (update) the BIOS
or not. Click Yes to proceed.

7. After the updating process is

finished, you will be asked you
to reboot the system. Click
OK to reboot.

8. While the system boots up and the full screen logo shows up, press
<Delete> key to enter BIOS setup.

After entering the BIOS setup, please go to the Save & Exit, using the Restore
Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.

21
Motherboard Manual
3. BIOSTAR BIOS Flasher
BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and
simple way to update your BIOS via USB pen drive.
Note1: This utility only allows storage device with FAT32/16 format and single partition.
Note2: Shutting down or resetting the system while updating the BIOS will lead to system
boot failure.

The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press
<F12> during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen

drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk

that contains the BIOS file to the USB port
or the floppy disk drive.

4. Power on or reset the computer and then

press <F12> during the POST process. A
select dialog as the picture on the right
appears. Select the device contains the
BIOS file and press <Enter> to enter the
utility.

5. The utility will show the BIOS files and their respective information. Select
the proper BIOS file and press <Enter> then <Y> to perform the BIOS
update process.

6. After the update process,

the utility will ask you to
reboot the system.
Press <Y> to proceed.
BIOS update completes.

22
 A780L3C

3.3 Software
Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program would
appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Note1: All the information and content about following software are subject to be changed without
notice. For better performance, the software is being continuously updated.
Note2: The information and pictures described below are for your reference only. The actual
information and settings on board may be slightly different from this manual.

Launching Software
After the installation process, you will see the software icon “eHOT Line” / “BIOS
Update” appears on the desktop. Double-click the icon to launch the utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our Tech-Support system.
This utility will collect the system information which is useful for analyzing the problem
you may have encountered, and then send these information to our tech-support
department to help you fix the problem.
Note: Before you use this utility, please set Outlook Express as your default e-mail client application program.

represents important
*
information that you
This block will show
must provide. Without
this information, you may
the information which * Describe condition
of your system.
would be collected in
not be able to send out the mail.
the mail.

*Select your area or

the area close to you.

Provide the e-mail

address that you would
like to send the copy to.

*Provide the name of

the memory module
manufacturer.

Provide the name of

the power supply
manufacturer and the
model no.

Send the mail out. Exit this dialog.

Save these information to a .txt file

23
Motherboard Manual

After filling up this information, click “Send”

to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you will see
a saving dialog appears asking you to enter file name.

Enter the file name and then click “Save”.

Your system information will be saved to
a .txt file.

Open the saved .txt file, you will see your

system information including
motherboard/BIOS/CPU/video/
device/OS information. This information
is also concluded in the sent mail.

Note1: We will not share customer’s data with any other third parties, so please feel free to
provide your system information while using eHot-Line service.
Note2: If you are not using Outlook Express as your default e-mail client application, you may
need to save the system information to a .txt file and send the file to our tech support with other
e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php for
getting our contact information.

24
 A780L3C
BIOScreen Utility (Optional)
This utility allows you to personalize your boot logo easily. You can choose
BMP as your boot logo so as to customize your computer.

Please follow the following instructions to update boot logo:

1. Load Image：Choose the picture as the boot logo.

2. Transform：Transform the picture for BIOS and preview the result.

3. Update Bios：Write the picture to BIOS Memory to complete the update.

25
Motherboard Manual

CHAPTER 4: USEFUL HELP

4.1 Driver Installation
After you installed your operating system, please insert the Fully Setup Driver
DVD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.
Note: If this window didn’t show up after you insert the Driver DVD, please use file browser
to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the
compatible driver for your motherboard and operating system. Click on each
device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide will list
the software available for your system, click on each software title to launch the
installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver DVD.
Click on the Manual icon to browse for available manual.
Note: You will need Acrobat Reader to open the manual file. Please download the latest
version of Acrobat Reader software from http://get.adobe.com/reader/

26
 A780L3C
4.2 Troubleshooting
Probable Solution
1. There is no power in the system. 1. Make sure power cable is
Power LED does not shine; the securely plugged in.
fan of the power supply does not 2. Replace cable.
work 3. Contact technical support.
2. Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit, the DIMM, press down firmly until the
and hard drives are running. module snaps into place.
System does not boot from a hard disk 1. Check cable running from disk to
drive, but can be booted from optical disk controller board. Make sure
drive. both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical 1. Back up data and applications
drive. Hard disks can be read, files.
applications can be used, but system 2. Reformat the hard drive.
fails to boot from a hard disk. Re-install applications and data
using backup disks.
Screen message shows “Invalid Review system’s equipment. Make sure
Configuration” or “CMOS Failure.” correct information is in setup.
System cannot boot after user installs a 1. Set master/slave jumpers
second hard drive. correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

27
Motherboard Manual
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown

automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.

Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.

28
 A780L3C
4.3 RAID Functions
Operating System
z Supports Windows XP, Windows Vista, and Windows 7.
Raid Arrays
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write
times for many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.
How RAID Works
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It
breaks up a large file into smaller blocks and performs disk reads and writes
across multiple drives in parallel. The size of each block is determined by the
stripe size parameter, which you set during the creation of the RAID set based
on the system environment. This technique reduces overall disk access time
and offers high bandwidth.
Features and Benefits
- Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.
- Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
- Benefits: provides increased data throughput, especially for large files.
No capcity loss penalty for parity.
- Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
- Fault Tolerance: No.
- Total Capacity: (Minimal. HDD Capacity) x (Connected HDDs Amount)

Block 1 Block 2
Block 3 Block 4
Block 5 Block 6

29
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a
RAID 1 array system. The mirrored (backup) copy of the data can reside on the
same disk or on a second redundant drive in the array. RAID 1 provides a
hot-standby copy of data if the active volume or drive is corrupted or becomes
unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive
and less reliable media.
Features and Benefits
- Drives: Minimum 2, and maximum is 2.
- Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
- Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
- Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
- Fault Tolerance: Yes.

Block 1 Block 1
Block 2 Block 2
Block 3 Block 3

30
 A780L3C
RAID 10:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
- Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.
- Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
- Fault Tolerance: Yes.

Block 1 Block 1 Block 2 Block 2

Block 3 Block 3 Block 4 Block 4
Block 5 Block 5 Block 6 Block 6

31
Motherboard Manual
APPENDIX: Specifications In Other Languages
German
Spezifikationen

Sockel AM3 Die AMD 64-Architektur unterstützt eine 32-Bit- und

CPU AMD Sempron / Phenom II / Athlon II 64-Bit-Datenverarbeitung

Prozessoren (Maximales Watt: 95W) Unterstützt Hyper Transport 2.0

Unterstützt Hyper Transport 3.0 mit einer

FSB
Bandbreite von bis zu 3.2 GT/s

AMD 760G
Chipsatz
AMD SB710

Low Pin Count-Schnittstelle

ITE8728F-BX
Umgebungskontrolle,
Super E/A Bietet die häufig verwendeten alten Super
Hardware-Überwachung
E/A-Funktionen.
"Smart Guardian"-Funktion von ITE

DDR3 DIMM-Steckplätze x 2
Dual-Kanal DDR3 Speichermodul
Arbeitsspeiche Max. 16GB Arbeitsspeicher
Unterstützt DDR3 800/1066/1333/1600(OC)
r Jeder DIMM unterstützt 512MB/1GB/
registrierte DIMMs. ECC DIMMs werden nicht unterstützt.
2GB/4GB/8GB DDR3.

Grafik Integrierter AMD 760G-Chipsatz Max. 1024MB gemeinsam benutzter Videospeicher

Datentransferrate bis zu 3 Gb/s

SATA Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version 2.0.

LAN Realtek RTL 8105T 10 / 100 Mb/s Auto-Negotiation

HD
5.1-Kanal-Audioausgabe
Audio-Unterstü VT1708B / ALC662
Unterstützt High-Definition Audio
tzung

PCI Express X16 Steckplatz x1

Steckplätze
PCI-Steckplatz x1

Onboard-Ansc SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

hluss IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

32
 A780L3C
Spezifikationen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfterstromversorgungsanschluss (mit Smart

CPU-Lüfter-Sockel x1
Fan-Funktion)

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-Sockel x1

USB-Anschluss x2 Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse

Stromanschluss (24-polig) x1

Stromanschluss (4-polig) x1

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

PS/2-Tastatur x1

PS/2-Maus x1

Rückseiten-E/ VGA-Anschluss x1

A LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

Platinengröße 182 mm (B) X 225 mm (L)

Sonderfunktion
Unterstützt RAID 0 / 1 / 10
en

Biostar behält sich das Recht vor, ohne Ankündigung die

OS-Unterstütz
Windows XP / Vista / 7 / 8 Unterstützung für ein Betriebssystem hinzuzufügen oder zu
ung
entfernen.

33
Motherboard Manual

French
SPEC

Socket AM3
L'architecture AMD 64 permet le calcul 32 et 64 bits
UC Processeurs AMD Sempron / Phenom II /
Prend en charge Hyper Transport 2.0
Athlon II (Watt maximum : 95W)

Prend en charge Hyper Transport 3.0 jusqu'à

Bus frontal
une bande passante de 3.2 GT/s

AMD 760G
Chipset
AMD SB710

Interface à faible compte de broches

ITE 8728F-BX
Initiatives de contrôle environnementales,
Super E/S Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Fonction "Gardien intelligent" de l'ITE

Fentes DDR3 DIMM x 2 Module de mémoire DDR3 à mode à double voie

Mémoire Capacité mémoire maximale de 16Go Prend en charge la DDR3 800/1066/1333/1600(OC)

principale Chaque DIMM prend en charge des DDR3 de Les DIMM à registres et DIMM avec code correcteurs

512Mo/1Go/2Go/4Go/8Go d'erreurs ne sont pas prises en charge

Graphiques Integré dans la chipset AMD 760G Mémoire vidéo partagée maximale de 1024 Mo

Taux de transfert jusqu'à 3 Go/s.

SATA Contrôleur Serial ATA intégré
Conforme à la spécification SATA Version 2.0

LAN Realtek RTL 8105T 10 / 100 Mb/s négociation automatique

Prise en
Sortie audio à 5.1 voies
charge audio VT1708B / ALC662
Prise en charge de l'audio haute définition
HD

Fente PCI Express X16 x1

Fentes
Fente PCI x1

Connecteur Connecteur SATA x4 Chaque connecteur prend en charge 1 périphérique SATA

embarqué
Connecteur IDE x1 Chaque connecteur prend en charge 2 périphériques IDE

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

34
 A780L3C
SPEC

Alimentation électrique du ventilateur UC (avec fonction de

Embase de ventilateur UC x1
ventilateur intelligent)

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Chaque connecteur prend en charge 2 ports USB de panneau

Connecteur USB x2
avant

Connecteur d'alimentation x1

(24 broches)

Connecteur d'alimentation x1

(4 broches)

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

Clavier PS/2 x1

Souris PS/2 x1
E/S du
Port VGA x1
panneau
Port LAN x1
arrière
Port USB x4

Fiche audio x3

Dimensions
182 mm (l) X 225 mm (H)
de la carte
Fonctionnalit
Prise en charge RAID 0 / 1 / 10
és spéciales

Biostar se réserve le droit d'ajouter ou de supprimer le support

Support SE Windows XP / Vista / 7 / 8
de SE avec ou sans préavis.

35
Motherboard Manual

Italian
SPECIFICA

Socket AM3 L’architettura AMD 64 abilita la computazione 32 e 64

CPU Processori AMD Sempron / Phenom II / bit

Athlon II (Watt massimo: 95W) Supporto di Hyper Transport 2.0

Supporto di HyperTransport 3.0 fino a 3.2

FSB
GT/s di larghezza di banda

AMD 760G
Chipset
AMD SB710

Interfaccia LPC (Low Pin Count)

ITE 8728F-BX
Funzioni di controllo dell’ambiente:
Super I/O Fornisce le funzionalità legacy Super I/O
Monitoraggio hardware
usate più comunemente.
Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR3 x 2

Modulo di memoria DDR3 a canale doppio
Memoria Capacità massima della memoria 16GB
Supporto di DDR3 800/1066/1333/1600(OC)
principale Ciascun DIMM supporta DDR3
DIMM registrati e DIMM ECC non sono supportati
512MB/1GB/2GB/4GB/8GB

Grafica Integrata nel Chipset AMD 760G La memoria video condivisa massima è di 1024 MB

Velocità di trasferimento dei dati fino a 3 Gb/s.

SATA Controller Serial ATA integrato
Compatibile specifiche SATA Versione 2.0.

LAN Realtek RTL 8105T Negoziazione automatica 10 / 100 Mb/s

Supporto Uscita audio 5.1 canali

VT1708B / ALC662
audio HD Supporto audio High-Definition (HD)

Alloggio PCI Express X16 x1

Alloggi
Alloggio PCI x1

Connettori Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

su scheda
Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore pannello frontale x1 Supporta i servizi del pannello frontale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Collettore ventolina CPU x1 Alimentazione ventolina CPU (con funzione Smart Fan)

36
 A780L3C
SPECIFICA

Collettore ventolina sistema x1 Alimentazione ventolina di sistema

Collettore cancellazione CMOS x1

Ciascun connettore supporta 2 porte USB pannello

Connettore USB x2
frontale

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x1

(4 pin)

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Tastiera PS/2 x1

Mouse PS/2 x1

I/O pannello Porta VGA x1

posteriore Porta LAN x1

Porta USB x4

Connettore audio x3

Dimensioni
182 mm (larghezza) x 225 mm (altezza)
scheda

Caratteristic
Supporto RAID 0 / 1 / 10
he speciali

Sistemi Biostar si riserva il diritto di aggiungere o rimuovere il

operativi Windows XP / Vista / 7 / 8 supporto di qualsiasi sistema operativo senza

supportati preavviso.

37
Motherboard Manual

Spanish
Especificación

Conector AM3
La arquitectura AMD 64 permite el procesado de 32 y 64 bits
CPU Procesadores AMD Sempron / Phenom II /
Soporta las tecnologías Hyper Transport 2.0
Athlon II (Vatio máximo: 95W)

Admite HyperTransport 3.0 con un ancho de

FSB
banda de hasta 3.2 GT/s

Conjunto de AMD 760G

chips AMD SB710

Interfaz de cuenta Low Pin

ITE 8728F-BX
Iniciativas de control de entorno,
Súper E/S Le ofrece las funcionalidades heredadas de uso
Monitor hardware
más común Súper E/S.
Función "Guardia inteligente" de ITE

Ranuras DIMM DDR3 x 2

Módulo de memoria DDR3 de canal Doble
Memoria Capacidad máxima de memoria de 16GB
Admite DDR3 de 800/1066/1333/1600(OC)
principal Cada DIMM admite DDR de
No admite DIMM registrados o DIMM compatibles con ECC
512MB/1GB/2GB/4GB/8GB

Gráficos Integrados en el conjunto de chips AMD 760G Memoria máxima de vídeo compartida de 1024 MB

Tasas de transferencia de hasta 3 Gb/s.

SATA Controlador ATA Serie Integrado
Compatible con la versión SATA 2.0.

Red Local Realtek RTL 8105T Negociación de 10 / 100 Mb/s

Soporte de Salida de sonido de 5.1 canales

VT1708B / ALC662
sonido HD Soporte de sonido Alta Definición

Ranura PCI Express X16 X1

Ranuras
Ranura PCI X1

Conectores Conector SATA X4 Cada conector soporta 1 dispositivos SATA

en placa
Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector de panel frontal X1 Soporta instalaciones en el panel frontal

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

38
 A780L3C
Especificación

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función

Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector soporta 2 puertos USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Teclado PS/2 X1

Ratón PS/2 X1

Panel trasero Puerto VGA X1

de E/S Puerto de red local X1

Puerto USB X4

Conector de sonido X3

Tamaño de
182 mm. (A) X 225 Mm. (H)
la placa

Funciones
Admite RAID 0 / 1 / 10
especiales

Soporte de
Biostar se reserva el derecho de añadir o retirar el soporte de
sistema Windows XP / Vista / 7 / 8
cualquier SO con o sin aviso previo.
operativo

39
Motherboard Manual

Portuguese
ESPECIFICAÇÕES

Socket AM3 A arquitectura AMD 64 permite uma computação de 32 e 64

CPU Processadores AMD Sempron / Phenom II / bits

Athlon II (Watt máximo: 95W) Suporta as tecnologias Hyper Transport 2.0

Suporta a tecnologia HyperTransport 2.0 com

FSB
uma largura de banda até 3.2 GT/s

AMD 760G
Chipset
AMD SB710

Interface LPC (Low Pin Count).

ITE 8728F-BX
Especificaçã Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais utilizadas
o Super I/O Monitorização do hardware
em termos da especificação Super I/O.
Função "Smart Guardian" da ITE

Ranhuras DIMM DDR3 x 2

Módulo de memória DDR3 de canal duplo
Capacidade máxima de memória: 16GB
Memória Suporta módulos DDR3 800/1066/1333/1600(OC)
Cada módulo DIMM suporta uma memória
principal Os módulos DIMM registados e os DIMM ECC não são
DDR3 de 512MB/1GB/
suportados
2GB/4GB/8GB

Placa gráfica Integrada no chipset AMD 760G Memória de vídeo máxima partilhada: 1024 MB

Velocidades de transmissão de dados até 3 Gb/s.

SATA Controlador Serial ATA integrado
Compatibilidade com a especificação SATA versão 2.0.

LAN Realtek RTL 8105T Auto negociação de 10 / 100 Mb/s

Suporte para
Saída de áudio de 5.1 canais
áudio de alta VT1708B / ALC662
Suporta a especificação High-Definition Audio
definição

Ranhura PCI Express X16 x1

Ranhuras
Ranhura PCI x1

Conectores Conector SATA x4 Cada conector suporta 1 dispositivo SATA

na placa
Conector IDE x1 Cada conector suporta 2 dispositivos IDE

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áudio frontal x1 Suporta a função de áudio no painel frontal

40
 A780L3C
ESPECIFICAÇÕES

Conector da ventoinha da CPU x1 Alimentação da ventoinha da CPU (com a função Smart Fan)

Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1

Conector USB x2 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 pinos)

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Teclado PS/2 x1

Rato PS/2 x1
Entradas/Saí
Porta VGA x1
das no painel
Porta LAN x1
traseiro
Porta USB x4

Tomada de áudio x3

Tamanho da
182 mm (L) X 225 mm (A)
placa
Característic
Suporta as funções RAID 0 / 1 / 10
as especiais
Sistemas
A Biostar reserva-se o direito de adicionar ou remover suporte
operativos Windows XP / Vista / 7 / 8
para qualquer sistema operativo com ou sem aviso prévio.
suportados

41
Motherboard Manual

Polish
SPEC

Socket AM3
Architektura AMD 64 umożliwia przetwarzanie 32 i 64 bitowe
Procesor AMD Sempron / Phenom II / Athlon II Procesory
Obsługa Hyper Transport 2.0
(Maksymalny Watt: 95W)

Obsługa HyperTransport 3.0 o szerokości

FSB
pasma do 3.2 GT/s

AMD 760G
Chipset
AMD SB710

Gniazda DDR3 DIMM x 2

Moduł pamięci DDR3 z trybem podwójnego kanału
Pamięć Maks. wielkość pamięci 16GB
Obsługa DDR3 800/1066/1333/1600(OC)
główna Każde gniazdo DIMM obsługuje moduły
Brak obsługi Registered DIMM oraz ECC DIMM
512MB/1GB/2GB/4GB/8GB DDR3

Interfejs Low Pin Count

ITE 8728F-BX
Funkcje kontroli warunków pracy,
Super I/O Zapewnia najbardziej powszechne funkcje
Monitor H/W
Super I/O.
Funkcja ITE "Smart Guardian"

Grafika Zintegrowana w chipsecie AMD 760G Maks. wielkość współdzielonej pamięci video wynosi 1024 MB

Transfer danych do 3 Gb/s.

SATA Zintegrowany kontroler Serial ATA
Zgodność ze specyfikacją SATA w wersji 2.0.

LAN Realtek RTL 8105T 10 / 100 Mb/s z automatyczną negocjacją szybkości

Obsługa 5.1 kanałowe wyjście audio

VT1708B / ALC662
audio HD Obsługa High-Definition Audio

Gniazdo PCI Express X16 x1

Gniazda
Gniazdo PCI x1

Złącza Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA

wbudowane
Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim

Złącze główkowe wentylatora procesora x1 Zasilanie wentylatora procesora (z funkcją Smart Fan)

42
 A780L3C
SPEC

Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora systemowego

Złącze główkowe kasowania CMOS x1

Złącze USB x2 Każde złącze obsługuje 2 porty USB na panelu przednim

Złącze zasilania (24 pinowe) x1

Złącze zasilania (4 pinowe) x1

Złącze Port drukarki x1 Każde złącze obsługuje 1 Port drukarki

Klawiatura PS/2 x1

Mysz PS/2 x1

Back Panel Port VGA x1

I/O Port LAN x1

Port USB x4

Gniazdo audio x3

Wymiary
182 mm (S) X 225 mm (W)
płyty

Funkcje
Obsługa RAID 0 / 1 / 10
specjalne

Obsluga
Biostar zastrzega sobie prawo dodawania lub odwoływania
systemu
Windows XP / Vista / 7 / 8 obsługi dowolnego systemu operacyjnego bez
operacyjneg
powiadomienia.
o

43
Motherboard Manual

Russian
СПЕЦ
CPU
Гнездо AM3 Архитектура AMD 64 разрешать обработка данных на 32 и
(центральн
Процессоры AMD Sempron / Phenom II / 64 бит
ый
процессор) Athlon II (Максимальный ватт: 95W) Поддержка Hyper Transport 2.0

Поддержка HyperTransport 3.0 с пропускной

FSB
способностью до 3.2 GT/s

Набор AMD 760G

микросхем AMD SB710

Слоты DDR3 DIMM x 2 Модуль памяти с двухканальным режимом DDR3

Основная Максимальная ёмкость памяти 16ГБ Поддержка DDR3 800/1066/1333/1600(OC)

память Каждый модуль DIMM поддерживает Не поддерживает зарегистрированные модули DIMM and

512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3 ECC DIMM

ITE 8728F-BX Интерфейс с низким количеством выводов

Обеспечивает наиболее используемые Инициативы по охране окружающей среды,

Super I/O
действующие функциональные Аппаратный монитор

возможности Super I/O. Функция ITE "Smart Guardian" (Интеллектуальная защита)

Максимальная совместно используемая видео память

Графика Встроенная в набор микросхем AMD 760G
составляет 1024 МБ

Встроенное последовательное устройство скорость передачи данных до 3 гигабит/с.

SATA
управления ATA Соответствие спецификации SATA версия 2.0.
Локальная
Realtek RTL 8105T Автоматическое согласование 10 / 100 Мб/с
сеть
Звуковая
поддержка Звуковая поддержка High-Definition
VT1708B / ALC662
жесткого 5.1канальный звуковой выход
диска

Слот PCI Express X16 x1

Слоты
Слот PCI x1
Встроенный Разъём SATA x4 Каждый разъём поддерживает 1 устройство SATA
разъём
Каждый разъём поддерживает 2 встроенных интерфейса
Разъём IDE x1
накопителей

Разъём на лицевой панели x1 Поддержка устройств на лицевой панели

Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели

44
 A780L3C
СПЕЦ

Контактирующее приспособление
Источник питания для вентилятора центрального
вентилятора центрального
процессора (с функцией интеллектуального вентилятора)
процессора x1

Контактирующее приспособление
Источник питания для вентилятора системы
вентилятора системы x1

Открытое контактирующее

приспособление CMOS x1

Каждый разъём поддерживает 2 USB-порта на лицевой

USB-разъём x2
панели

Разъем питания (24 вывод) x1

Разъем питания (4 вывод) x1

Разъём Порт подключения Каждый разъём поддерживает 1 Порт подключения

принтера x1 принтера

Клавиатура PS/2 x1

Мышь PS/2 x1
Задняя
панель Порт VGA x1

средств Порт LAN x1

ввода-выво USB-порт x4
да
Гнездо для подключения

наушников x3
Размер
182 мм (Ш) X 225 мм (В)
панели
Специальн
ые
технические Поддержка RAID 0 / 1 / 10
характерист
ики

Biostar сохраняет за собой право добавлять или удалять

Поддержка
Windows XP / Vista / 7 / 8 средства обеспечения для OS с или без
OS
предварительного уведомления.

45
‫‪Motherboard Manual‬‬

‫‪Arabic‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬

‫‪AM3‬ﻣﻘﺒﺲ‬
‫إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺑﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬ ‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪AMD Sempron / Phenom II / Athlon II‬ﻣﻌﺎﻟﺠﺎت‬
‫و ‪Hyper Transport2.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬ ‫اﻟﻤﺮآﺰﻳﺔ‬
‫)و‪: 95‬ﻗﺼﻮى واط(‬

‫اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻧﺒﻲ ‪ 3.2 GT/s‬ﺑﺘﺮدد ﻳﺼﻞ إﻟﻰ‪HyperTransport 3.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬

‫‪AMD 760G‬‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪AMD SB710‬‬

‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬

‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬ ‫‪ITE 8728F-BX‬‬

‫‪Super I/O‬‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺟﻬﺰة‬ ‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬

‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬

‫ﻣﺰدوﺟﺔ اﻟﻘﻨﺎة‪DDR3‬وﺣﺪة ذاآﺮة‬ ‫ﻋﺪد‪2‬‬ ‫ﻓﺘﺤﺔ ‪DDR3 DIMM‬‬

‫ﺳﻌﺎت ‪DDR3 (OC)1600/1333/1066/800‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻧﻮع‬ ‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 16‬ﺟﻴﺠﺎ ﺑﺎﻳﺖ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﻣﻴﺠﺎ ﺑﺎﻳﺖ‬ ‫ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ /512‬ﺳﻌﺔ ‪ DDR3‬ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻧﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬

‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬ ‫و‪ /1‬و‪ /2‬و‪ /4‬و‪ 8‬ﺟﻴﺠﺎ ﺑﺎﻳﺖ‬

‫أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ ‪ 1024‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‬ ‫‪ AMD 760G‬ﻣﺪﻣﺠﺔ ﻓﻲ رﻗﺎﺋﻖ‬ ‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻣﺎت‬

‫ﺟﻴﺠﺎﺑﺖ‪/‬ﺛﺎﻧﻴﺔ‪3.‬ﻧﻘﻞ اﻟﺒﻴﺎﻧﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ‬

‫ﻣﺘﻜﺎﻣﻞ‪Serial ATA‬ﻣﺘﺤﻜﻢ‬ ‫‪SATA‬‬
‫‪ 2.0.‬اﻹﺻﺪار ‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺻﻔﺎت‬

‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺛﺎﻧﻴﺔ‬ ‫‪Realtek RTL 8105T‬‬ ‫ﺷﺒﻜﺔ داﺧﻠﻴﺔ‬

‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪5.1‬‬ ‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬

‫‪VT1708B / ALC662‬‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻣﻦ‬ ‫اﻟﺘﻌﺮﻳﻒ‬

‫ﻋﺪد ‪1‬‬ ‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬

‫اﻟﻔﺘﺤﺎت‬
‫ﻋﺪد‪1‬‬ ‫ﻓﺘﺤﺔ ‪PCI‬‬

‫‪SATA‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺟﻬﺰة‬ ‫ﻋﺪد‪4‬‬ ‫ﻣﻨﻔﺬ ‪SATA‬‬ ‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬

‫اﻟﻠﻮﺣﺔ‬
‫‪IDE‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺛﻨﻴﻦ ﻣﻦ أﺟﻬﺰة‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ‪IDE‬‬

‫ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬

‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬

‫‪46‬‬
 ‫‪A780L3C‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬

‫‪Smart Fan‬ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ‬ ‫ﻋﺪد ‪1‬‬ ‫وﺻﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬

‫ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬ ‫ﻋﺪد ‪1‬‬ ‫وﺻﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬

‫ﻋﺪد ‪1‬‬ ‫وﺻﻠﺔ ﻣﺴﺢ ‪CMOS‬‬

‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‪USB‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ‬ ‫ﻋﺪد ‪2‬‬ ‫ﻣﻨﻔﺬ ‪USB‬‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﻮس(‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ‬

‫ﻋﺪد ‪1‬‬ ‫ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ ‪PS/2‬‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﺎوس ‪PS/2‬‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ‪VGA‬‬ ‫ﻣﻨﺎﻓﺬ دﺧﻞ‪/‬ﺧﺮج‬

‫ﻋﺪد ‪1‬‬ ‫ﻣﻨﻔﺬ ﺷﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ‬ ‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬

‫ﻋﺪد‪4‬‬ ‫ﻣﻨﺎﻓﺬ ‪USB‬‬

‫ﻋﺪ‪3‬‬ ‫ﻣﻘﺒﺲ ﺻﻮت‬

‫‪ 182‬ﻣﻢ )ﻋﺮض( ‪ 225 X‬ﻣﻢ )ارﺗﻔﺎع(‬ ‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬

‫‪RAID 0 / 1 / 10‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬ ‫ﻣﺰاﻳﺎ ﺧﺎﺻﺔ‬

‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺧﻄﺎر أو ‪Biostar‬ﺗﺤﺘﻔﻆ‬

‫‪Windows XP / Vista / 7 / 8‬‬ ‫دﻋﻢ أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫ﺑﺪون إﺧﻄﺎر‪.‬‬

‫‪47‬‬
Motherboard Manual

Japanese
仕様

AMD 64アーキテクチャでは、32ビットと64ビット計算が可能
Socket AM3
です
CPU AMD Sempron / Phenom II / Athlon II プロセッ
ハイパートランスポート2.0とクールアンドクワイアットをサ
サ (最高のワット: 95W)
ポートします

3.2 GT/sのバンド幅までハイパートランスポー
FSB
ト3.0をサポートします

チップセッ AMD 760G

ト AMD SB710

DDR3 DIMMスロット x 2
デュアル チャンネルモードDDR3メモリモジュール
メインメモ 最大メモリ容量16GB
DDR3 800/1066/1333/1600(OC) をサポート
リ 各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3
登録済みDIMMとECC DIMMはサポートされません
をサポート

低ピンカウントインターフェイス
ITE 8728F-BX
環境コントロールイニシアチブ、
Super I/O もっとも一般に使用されるレガシーSuper I/O
H/Wモニター
機能を採用しています。
ITEの「スマートガーディアン」機能

グラフィッ
AMD 760Gチップセットに統合 最大の共有ビデオメモリは1024MBです
クス

最高3Gb/秒のデータ転送速度
SATA 統合シリアルATAコントローラ
SATAバージョン2.0仕様に準拠。

LAN Realtek RTL 8105T 10 / 100 Mb/秒のオートネゴシエーション

HDオーディ
5.1チャンネルオーディオアウト
オのサポー VT1708B / ALC662
ハイデフィニションオーディオのサポート
ト

PCI Express X16スロット x1

スロット
PCIスロット x1

オンボード SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします

コネクタ
IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします

フロントパネルコネクタ x1 フロントパネル機能をサポートします

48
 A780L3C
仕様

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ x1 システムファン電源装置

CMOSクリアヘッダ x1

各コネクタは2つのフロントパネルUSBポートをサポートし
USBコネクタ x2
ます

電源コネクタ(24ピン) x1

電源コネクタ(4ピン) x1

プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします

PS/2キーボード x1

PS/2マウス x1

背面パネル VGAポート x1

I/O LANポート x1

USBポート x4

オーディオジャック x3

ボードサイ
182 mm (幅) X 225 mm (高さ)
ズ

特殊機能 RAID 0 / 1 / 10 のサポート

Biostarは事前のサポートなしにOSサポートを追加または削
OSサポート Windows XP / Vista / 7 / 8
除する権利を留保します。

2013/04/01

49