Magnetic

declination

Magnetic declination, or magnetic

variation, is the angle on the horizontal
plane between magnetic north (the
direction the north end of a magnetized
compass needle points, corresponding to
the direction of the Earth's magnetic field
lines) and true north (the direction along a
meridian towards the geographic North
Pole). This angle varies depending on
position on the Earth's surface and
changes over time.

Example of magnetic declination showing a compass

needle with a "positive" (or "easterly") variation from
geographic north. Ng is geographic or true north, Nm is
magnetic north, and δ is magnetic declination

Somewhat more formally, Bowditch

defines variation as “the angle between
the magnetic and geographic meridians at
any place, expressed in degrees and
minutes east or west to indicate the
direction of magnetic north from true
north. The angle between magnetic and
grid meridians is called grid magnetic
angle, grid variation, or grivation.”[1]

By convention, declination is positive when

magnetic north is east of true north, and
negative when it is to the west. Isogonic
lines are lines on the Earth's surface along
which the declination has the same
constant value, and lines along which the
declination is zero are called agonic lines.
The lowercase Greek letter δ (delta) is
frequently used as the symbol for
magnetic declination.

The term magnetic deviation is sometimes

used loosely to mean the same as
magnetic declination, but more correctly it
refers to the error in a compass reading
induced by nearby metallic objects, such
as iron on board a ship or aircraft.

Magnetic declination should not be

confused with magnetic inclination, also
known as magnetic dip, which is the angle
that the Earth's magnetic field lines make
with the downward side of the horizontal
plane.
Declination change over time
and location
Magnetic declination varies both from
place to place and with the passage of
time. As a traveller cruises the east coast
of the United States, for example, the
declination varies from 16 degrees west in
Maine, to 6 in Florida, to 0 degrees in
Louisiana, to 4 degrees east (in Texas).
The declination at London, UK was one
degree west (2014), reducing to zero as of
early 2020. [2] [3]

In most areas, the spatial variation reflects

the irregularities of the flows deep in the
Earth; in some areas, deposits of iron ore
or magnetite in the Earth's crust may
contribute strongly to the declination.
Similarly, secular changes to these flows
result in slow changes to the field strength
and direction at the same point on the
Earth.

NIMA
Magnetic
Variation
Level curves drawn on a declination map Map 2000
to denote the magnetic declination,
described by signed degrees. Each level
curve is an isogonic line.
The magnetic declination in a given area
may (most likely will) change slowly over
time, possibly as little as 2–2.5 degrees
every hundred years or so, depending upon
how far from the magnetic poles it is. For
a location closer to the pole like Ivujivik,
the declination may change by 1 degree
every three years. This may be
insignificant to most travellers, but can be
important if using magnetic bearings from
old charts or metes (directions) in old
deeds for locating places with any
precision.

As an example of how variation changes

over time, see the two charts of the same
area (western end of Long Island Sound),
below, surveyed 124 years apart. The 1884
chart shows a variation of 8 degrees, 20
minutes West. The 2008 chart shows 13
degrees, 15 minutes West.

Western Long Western Long

Island Sound, Island Sound,
1884 2008

Determining declination
Magnetic declination indicated on an Israeli map. The
arrows show true north, grid north and magnetic
north, and the caption explains that the average yearly
change in the magnetic declination is 0°03′ eastward.

Direct measurement …
Antique declinometer

The magnetic declination at any particular

place can be measured directly by
reference to the celestial poles—the points
in the heavens around which the stars
appear to revolve, which mark the direction
of true north and true south. The
instrument used to perform this
measurement is known as a declinometer.

The approximate position of the north

celestial pole is indicated by Polaris (the
North Star). In the northern hemisphere,
declination can therefore be approximately
determined as the difference between the
magnetic bearing and a visual bearing on
Polaris. Polaris currently traces a circle
0.73° in radius around the north celestial
pole, so this technique is accurate to
within a degree. At high latitudes a plumb-
bob is helpful to sight Polaris against a
reference object close to the horizon, from
which its bearing can be taken.[4]

Determination from maps and

models
…

A rough estimate of the local declination

(within a few degrees) can be determined
from a general isogonic chart of the world
or a continent, such as those illustrated
above. Isogonic lines are also shown on
aeronautical and nautical charts.

Larger-scale local maps may indicate

current local declination, often with the aid
of a schematic diagram. Unless the area
depicted is very small, declination may
vary measurably over the extent of the
map, so the data may be referred to a
specific location on the map. The current
rate and direction of change may also be
shown, for example in arcminutes per year.
The same diagram may show the angle of
grid north (the direction of the map's
north-south grid lines), which may differ
from true north.
On the topographic maps of the U.S.
Geological Survey (USGS), for example, a
diagram shows the relationship between
magnetic north in the area concerned
(with an arrow marked "MN") and true
north (a vertical line with a five-pointed
star at its top), with a label near the angle
between the MN arrow and the vertical
line, stating the size of the declination and
of that angle, in degrees, mils, or both.

A prediction of the current magnetic

declination for a given location (based on
a worldwide empirical model of the deep
flows described above) can be obtained
online from a web page operated by the
National Geophysical Data Center, a
division of the National Oceanic and
Atmospheric Administration of the United
States.[5] This model is built with all the
information available to the map-makers
at the start of the five-year period it is
prepared for. It reflects a highly predictable
rate of change, and is usually more
accurate than a map—which is likely
months or years out of date—and almost
never less accurate.

Software …

The National Geospatial-Intelligence

Agency (NGA) provides source code
written in C that is based on the World
Magnetic Model (WMM). The source code
is free to download and includes a data file
updated every five years to account for
movement of the magnetic north pole.

Using the declination

Adjustable compasses …

Adjustable compass set to a declination of 0° and a

Adjustable compass set to a declination of 0 and a
bearing of 312°

A magnetic compass points to magnetic

north, not geographic north. Compasses
of the style commonly used for hiking
include a declination adjustment in the
form of a bezel which swivels relative to
the base plate. To establish a declination
the bezel is rotated until the desired
number of degrees plus or minus lie
between the bezel's designation N (for
North) and the direction indicated by the
magnetic end of the needle (usually
painted red). This allows the user to
establish a true bearing for travel or
orientation by aligning the embossed red
indicator arrow on the base plate with a
landmark or heading on a map. A
compass thus adjusted can be said to be
reading “true north” instead of magnetic
north (as long as it remains within an area
on the same isogonic line).

In the image to the left, the bezel's N has

been aligned with the direction indicated
by the magnetic end of the compass
needle, reflecting a magnetic declination
of 0 degrees. The arrow on the base plate
indicates a bearing of 312 degrees.

Non-adjustable compasses …
How to compensate for magnetic declination when
reading a compass. In this example, the declination is
14°E (+14°), so the compass card points to a "north"
14 degrees to the East of true North. To obtain a true
bearing, add 14 degrees to the bearing shown by the
compass.

To work with both true and magnetic

bearings, the user of a non-adjustable
compass needs to make simple
calculations that take into account the
local magnetic declination. The example
on the left shows how you would convert a
magnetic bearing (one taken in the field
using a non-adjustable compass) to a true
bearing (one that you could plot on a map)
by adding the magnetic declination. The
declination in the example is 14°E (+14°).
If, instead, the declination was 14°W
(−14°), you would still “add” it to the
magnetic bearing to obtain the true
bearing: 40°+ (−14°) = 26°.

The opposite procedure is used in

converting a true bearing to a magnetic
bearing. With a local declination of 14°E, a
true bearing (perhaps taken from a map)
of 54° is converted to a magnetic bearing
(for use in the field) by subtracting the
declination: 54° – 14° = 40°. If, instead, the
declination was 14°W (−14°), you would
still “subtract” it from the true bearing to
obtain the magnetic bearing: 54°- (−14°) =
68°.

Navigation
On aircraft or vessels there are three types
of bearing: true, magnetic, and compass
bearing. Compass error is divided into two
parts, namely magnetic variation and
magnetic deviation, the latter originating
from magnetic properties of the vessel or
aircraft. Variation and deviation are signed
quantities. As discussed above, positive
(easterly) variation indicates that magnetic
north is east of geographic north.
Likewise, positive (easterly) deviation
indicates that the compass needle is east
of magnetic north.[6]

Compass, magnetic and true bearings are

related by:

The general equation relating compass

and true bearings is
Where:

is Compass bearing
is Magnetic bearing
is True bearing
is magnetic Variation
is compass Deviation
for Westerly Variation
and Deviation
for Easterly Variation
and Deviation

For example, if the compass reads 32°, the

local magnetic variation is −5.5° (i.e. West)
and the deviation is 0.5° (i.e. East), the true
bearing will be:
To calculate true bearing from compass
bearing (and known deviation and
variation):

Compass bearing + deviation =

magnetic bearing
Magnetic bearing + variation = true
bearing

To calculate compass bearing from true

bearing (and known deviation and
variation):

True bearing - variation = Magnetic

bearing
 Magnetic bearing - deviation = Compass
bearing

These rules are often combined with the

mnemonic "West is Best, East is least";
that is to say, add W declinations when
going from True bearings to Magnetic
bearings, and subtract E ones.

Another simple way to remember which

way to apply the correction for Continental
USA is:

For locations east of the agonic line

(zero declination), roughly east of the
Mississippi: The magnetic bearing is
always bigger.
 For locations west of the agonic line
(zero declination), roughly west of the
Mississippi: The magnetic bearing is
always smaller.

Common abbreviations are:

TC = true course;
V = variation (of the Earth's magnetic
field);
MC = magnetic course (what the course
would be in the absence of local
deviation);
D = deviation caused by magnetic
material (mostly iron and steel) on the
vessel;
 CC = compass course.

Deviation …

Magnetic deviation is the angle from a

given magnetic bearing to the related
bearing mark of the compass. Deviation is
positive if a compass bearing mark (e.g.,
compass north) is right of the related
magnetic bearing (e.g., magnetic north)
and vice versa. For example, if the boat is
aligned to magnetic north and the
compass' north mark points 3° more east,
deviation is +3°. Deviation varies for every
compass in the same location and
depends on such factors as the magnetic
field of the vessel, wristwatches, etc. The
value also varies depending on the
orientation of the boat. Magnets and/or
iron masses can correct for deviation, so
that a particular compass accurately
displays magnetic bearings. More
commonly, however, a correction card lists
errors for the compass, which can then be
compensated for arithmetically. Deviation
must be added to compass bearing to
obtain magnetic bearing.

Air navigation …

Magnetic declination has a very important

influence on air navigation, since the most
simple aircraft navigation instruments are
designed to determine headings by
locating magnetic north through the use of
a compass or similar magnetic device.

Aviation sectionals (maps / charts) and

databases used for air navigation are
based on true north rather than magnetic
north, and the constant and significant
slight changes in the actual location of
magnetic north and local irregularities in
the planet's magnetic field require that
charts and databases be updated at least
twice each year to reflect the current
magnetic variation correction from true
north.
For example, as of March 2010, near San
Francisco, magnetic north is about 14.3
degrees east of true north, with the
difference decreasing by about 6 minutes
of arc per year.[7]

When plotting a course, most small

aircraft pilots plot a trip using true north on
a sectional (map), then convert the true
north bearings to magnetic north for in-
plane navigation using the magnetic
compass. These bearings are then
converted on a pre-flight plan by adding or
subtracting the local variation displayed on
a sectional.
Radionavigation aids located on the
ground, such as VORs, are also checked
and updated to keep them aligned with
magnetic north to allow pilots to use their
magnetic compasses for accurate and
reliable in-plane navigation.

Runways are designated by a number

between 01 and 36, which is generally one
tenth of the magnetic azimuth of the
runway's heading: a runway numbered 09
points east (90°), runway 18 is south
(180°), runway 27 points west (270°) and
runway 36 points to the north (360° rather
than 0°).[8] However, due to magnetic
declination, changes in runway
designators have to occur at times to keep
their designation in line with the runway's
magnetic heading. An exception is made
for runways within the Northern Domestic
Airspace of Canada; these are numbered
relative to true north because proximity to
the magnetic North Pole makes the
magnetic declination large.

GPS systems used for air navigation can

use magnetic north or true north. In order
to make them more compatible with
systems that depend on magnetic north,
magnetic north is often chosen, at the
pilot's preference. The GPS receiver
natively reads in true north, but can
elegantly calculate magnetic north based
on its true position and data tables; the
unit can then calculate the current location
and direction of the north magnetic pole
and (potentially) any local variations, if the
GPS is set to use magnetic compass
readings.

See also
 Geography portal
Compass survey
Geomagnetism
L-shell
Magnetic inclination
 Pole star
Shen Kuo
Voyages of Christopher Columbus

References
1. Bowditch, Nathaniel (2002). American
Practical Navigator. Paradise Cay
Publications. p. 849.
ISBN 9780939837540.
2. "Find the magnetic declination at your
location" . Magnetic-Declination.com.
Retrieved 6 December 2013.
3. "World Magnetic Model - Epoch 2020 -
Declination" (PDF).
4. Magnetic declination, what it is , how
to compensate. , archived from the
original on 2010-01-07, retrieved
2010-03-03
5. "Estimated Value of Magnetic
Declination" . Geomagnetism. NOAA
National Geophysical Data Center.
Retrieved 6 December 2013.
. Willemsen, Diederik. "Compass
navigation" . SailingIssues. Retrieved
4 January 2020.
7. According to NOAA Geophysical Data
Center on-line model
. Federal Aviation Administration
Aeronautical Information Manual,
 Chapter 2, Section 3 Airport Marking
Aids and Signs part 3b Archived
2012-01-18 at the Wayback Machine

External links
USGS Geomagnetism Program
Looks up your IP address location and
tells you your declination.
Online declination calculator at the
National Geophysical Data Center
(NGDC)
Online declination and field strength
calculator at the NGDC
Mobile web-app for magnetic
declination at the NGDC
 Historical magnetic declination viewer
at the NGDC
Magnetic declination calculator at
Natural Resources Canada
A Google spreadsheet application to
bulk calculate magnetic declination
World Magnetic Model source code
download site

Retrieved from
"https://en.wikipedia.org/w/index.php?
title=Magnetic_declination&oldid=981048534"

Last edited 3 months ago by ClueBot NG

Content is available under CC BY-SA 3.0 unless
otherwise noted.