Scribd
Upload
220 views1 page

JM - CalCoat 127 - Data Sheet

Uploaded by

david messier
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
220 views1 page

JM - CalCoat 127 - Data Sheet

Uploaded by

david messier
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

INDUSTRIAL INSULATION

CALCOAT-127®
ONE-COAT FINISHING CEMENT

DATA SHEET

CALCOAT-127
CalCoat-127 is a proprietary blend of hydraulic cement, calcium silicate and inorganic mineral fibers that provides a smooth finish over
high-temperature insulation. No wire mesh is required. It can also be used as a general-purpose insulating cement, as it is easy to
trowel and resists wetting after initial application. CalCoat-127 can be painted with water or oil-base paints.

ADVANTAGES
• Dries to a smooth, paintable surface.
• Easy to apply, with no mesh required.

APPLICATIONS
Due to its composition and low thermal conductivity, CalCoat-127 is
recommended for finishing use with calcium silicate or perlite insulation
in high-temperature piping and equipment applications. CalCoat 127
can also be used to fill voids in mineral wool insulations. Because of
its corrosion inhibiting properties, it is especially recommended for
industrial processing and power generating facility applications and
operating at temperatures up to 1200°F (650°C).
Application Instructions
1. Mix with clean water until desired consistency is reached. PRODUCT CERTIFICATION
2. Set time approx. 2 hrs. (depends upon environmental conditions). When ordering material to comply with any government specification
3. Allow to cure for 24 hrs. prior to applying heat. or any other listed specification, a statement of that fact must appear
on the purchase order. Government regulations and other listed
AVAILABLE FORMS AND SIZES specifications require specific lot testing, and prohibit the certification
CalCoat-127 is packaged in a moisture resistant, heavy-duty of compliance after shipment has been made. There may be additional
poly bag, with a convenient built-in handle, containing 45 lbs. (20.4 kgs). charges associated with specification compliance testing. Please refer
to IND-CSP-3 for Certification Procedures and Charges. Call customer
SPECIFICATION COMPLIANCE service for more information.

ASTM C166
Less than 10% QUALITY STATEMENT
Volume Change on Drying
Johns Manville products are designed, manufactured and tested to strict
ASTM C449 Material Specification Passes quality standards in our own facilities. This along with third party auditing
ASTM C356 Linear Shrinkage Less than 5% is your assurance that this product delivers consistent high quality.
Dry Coverage Capacity 30 ft2 at 1”(2.8 m2 at 25 mm)
ADDITIONAL INFORMATION AND SDS
Bulk Density 20 lbs/ft3 (320.4 kgs./m3)
Please visit our website at www.jm.com/industrial
NRC 1.36 / MIL-DTL-24244 / ASTM C795 Passes (Mixed with DI water) Customer Service, Technical & General Information: (800) 866-3234

Technical specifications as shown in this literature are intended to be used as general


guidelines only. Please refer to the Safety Data Sheet and product label prior to using
this product. The physical and chemical properties of the MinWool-1200® Fab Board
Insulation listed herein represent typical, average values obtained in accordance
with accepted test methods and are subject to normal manufacturing variations. They
are supplied as a technical service and are subject to change without notice. Any
717 17th St.
references to numerical flame spread or smoke developed ratings are not intended to
Denver, CO 80202 reflect hazards presented by these or any other materials under actual fire conditions.
(800) 866-3234 Check with the Regional Sales Office nearest you for current information.
JM.com
All Johns Manville products are sold subject to Johns Manville’s standard Terms and
Conditions, which includes a Limited Warranty and Limitation of Remedy. For a copy of the
Johns Manville standard Terms and Conditions or for information on other Johns Manville
thermal insulation and systems, visit www.jm.com/terms-conditions or call (800) 654-3103.
IND-12 7/28/20 (Replaces 01/15) © 2020 Johns Manville All Rights Reserved

You might also like