TS3022

Datasheet

Rail-to-rail 1.8 V high-speed dual comparator

TS3022
SO-8/MiniSO-8
Features
• Propagation delay: 38 ns
• Low current consumption: 73 µA
• Rail-to-rail inputs
• Push-pull outputs
Pin connections (top view) • Supply operation from 1.8 to 5 V
• Wide temperature range: -40 °C to 125 °C
• ESD tolerance: 5 kV HBM, 300 V MM
• Latch-up immunity: 200 mA
• SMD packages
• Automotive qualification

Applications
• Telecom
• Instrumentation
• Signal conditioning
• High-speed sampling systems
• Portable communication systems
• Automotive

Maturity status link Description

TS3022 The TS3022 dual comparator features a high speed response time with rail-to-rail
inputs. With a supply voltage specified from 2 to 5 V, this comparator can operate
over a wide temperature range: -40 °C to 125 °C.
The TS3022 comparator offers micropower consumption as low as a few tens of
microamperes thus providing an excellent ratio of power consumption current versus
response time.
The TS3022 includes push-pull outputs and is available in small packages (SMD):
SO-8 and MiniSO-8.

DS6029 - Rev 5 - October 2020 www.st.com

For further information contact your local STMicroelectronics sales office.
 TS3022
Absolute maximum ratings and operating conditions

1 Absolute maximum ratings and operating conditions

Table 1. Absolute maximum ratings (AMR)

Symbol Parameter Value Unit

VCC Supply voltage (1) 5.5

VID Differential input voltage (2) ±5 V

VIN Input voltage range (VCC-) - 0.3 to (VCC+) + 0.3

SO-8 125
Rthja Thermal resistance junction-to-ambient (3)
MiniSO-8 90
°C/W
SO-8 40
Rthjc Thermal resistance junction-to-case (3)
MiniSO-8 39
Tstg Storage temperature -65 to 150

Tj Junction temperature 150 °C

TLEAD Lead temperature (soldering 10 s) 260

HBM: human body model (4) 5000

MM: machine model (5) 300

ESD V
CDM : charged device model for TS3022IDT and TS3022IST (6) 1500

CDM : charged device model for TS3022IYST (6) 1400

Latch-up immunity 200 mA

1. All voltage values, except the differential voltage are referenced to (VCC-). VCC is defined as the difference between VCC+
and VCC-.
2. The magnitude of the input and output voltages must never exceed the supply rail ±0.3 V.
3. Short-circuits can cause excessive heating. These are typical values.
4. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ resistor
between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the
device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected pin combinations
while the other pins are floating.
6. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly
to the ground through only one pin. This is done for all pins.

Table 2. Operating conditions

Symbol Parameter Value Unit

0 °C < Tamb < +125 °C 1.8 to 5

VCC Supply voltage
-40 °C < Tamb < +125°C 2 to 5
V
-40 °C < Tamb < 85 °C (VCC- ) - 0.2 to (VCC+) + 0.2
Vicm Common mode input voltage range
+85 °C < Tamb < +125 °C (VCC- ) to (VCC+)

Toper Operating temperature range -40 to 125 °C

DS6029 - Rev 5 page 2/20

 TS3022
Electrical characteristics

2 Electrical characteristics

Table 3. Electrical characteristics at VCC+ = 2 V, VCC- = 0 V, Tamb = 25 ° C, and full Vicm range (unless otherwise
specified)

Symbol Parameter Test conditions (1) Min. Typ. Max. Unit

0.5 6
VIO Input offset voltage -40 °C < Tamb < +125 °C, TS3021A mV
7
ΔVio/ΔT Input offset voltage drift -40 °C < Tamb < 125 °C 3 20 µV/°C

Tamb 1 20
IIO Input offset current (2)
-40 °C < Tamb < +125 °C 100
nA
Tamb 86 160
IIB Input bias current (2)
-40 °C < Tamb < 125 °C 300
No load, output high, Vicm = 0 V 73 90
No load, output high, Vicm = 0 V,
115
-40 °C < Tamb < 125 °C
ICC Supply current µA
No load, output low, Vicm = 0 V 84 105
No load, output low, Vicm = 0 V,
125
-40 °C < Tamb < 125 °C
Source 9
ISC Short-circuit current mA
Sink 10
Isource = 1 mA 1.88 1.92
VOH Output voltage high V
-40 °C < Tamb < 125 °C 1.80
Isink = 1 mA 60 100
VOL Output voltage low mV
-40 °C < Tamb < 125 °C 150
Common mode rejection
CMRR 0 < Vicm < 2 V 67
ratio dB
SVR Supply voltage rejection ∆Vcc = 2 to 5 V 58 73
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
38 60
Propagation delay, low to overdrive = 100 mV
TPLH
high output level (3) Vicm = 0 V, f = 10 kHz, CL = 50 pF,
48 75
overdrive = 20 mV
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
40 60
Propagation delay, high to overdrive = 100 mV
TPHL ns
low output level (4) Vicm = 0 V, f = 10 kHz, CL = 50 pF,
49 75
overdrive = 20 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
TF Fall time 8
overdrive = 100 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
TR Rise time 9
overdrive = 100 mV

1. All values over the temperature range are guaranteed through correlation and simulation. No production test
is performed at the temperature range limits.
2. Maximum values include unavoidable inaccuracies of the industrial tests
3. Response time is measured at 50% of the final output value with the following conditions: inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive.
4. Response time is measured at 50% of the final output value with the following conditions: inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive.

DS6029 - Rev 5 page 3/20

 TS3022
Electrical characteristics

Table 4. Electrical characteristics at VCC+= 3.3 V, VCC- = 0 V, Tamb = 25 ° C, and full Vicm range (unless otherwise
specified)

Symbol Parameter Test conditions (1) Min. Typ. Max. Unit

0.2 6
VIO Input offset voltage -40 °C < Tamb < 125 °C mV
7
ΔVio/ΔT Input offset voltage drift -40 °C < Tamb < 125 °C 3 20 µV/°C

Tamb 1 20
IIO Input offset current (2)
-40 °C < Tamb < +125 °C 100
nA
Tamb 86 160
IIB Input bias current (2)
-40 °C < Tamb < +125 °C 300
No load, output high, Vicm = 0 V 75 90
No load, output high, Vicm = 0 V,
120
-40 °C < Tamb < 125 °C
ICC Supply current µA
No load, output low, Vicm = 0 V 86 110
No load, output low, Vicm = 0 V,
125
-40 °C < Tamb < 125 °C
Source 26
ISC Short-circuit current mA
Sink 24
Isource = 1 mA 3.20 3.25
VOH Output voltage high V
-40 °C < Tamb < 125 °C 3.10
Isink = 1 mA 40 80
VOL Output voltage low mV
-40 °C < Tamb < 125 °C 150
Common mode rejection
CMRR 0 < Vicm < 3.3 V 75
ratio dB
SVR Supply voltage rejection ∆Vcc = 2 to 5 V 58 73
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
39 65
Propagation delay, low to overdrive = 100 mV
TPLH
high output level (3) Vicm = 0 V, f = 10 kHz, CL = 50 pF,
50 85
overdrive = 20 mV
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
41 65
Propagation delay, high to overdrive = 100 mV
TPHL ns
low output level (4) Vicm = 0 V, f = 10 kHz, CL = 50 pF,
51 80
overdrive = 20 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
TF Fall time 5
overdrive = 100 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
TR Rise time 7
overdrive = 100 mV

1. All values over the temperature range are guaranteed through correlation and simulation. No production test
is performed at the temperature range limits.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
3. Response time is measured at 50% of the final output value with the following conditions: inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive.
4. Response time is measured at 50% of the final output value with the following conditions: Inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive.

DS6029 - Rev 5 page 4/20

 TS3022
Electrical characteristics

Table 5. Electrical characteristics at VCC = 5 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified)

Symbol Parameter Test conditions (1) Min. Typ. Max. Unit

0.2 6
VIO Input offset voltage -40 °C < Tamb < 125 °C, TS3021A mV
7
ΔVio/ΔT Input offset voltage drift -40 °C < Tamb < 125 °C 3 20 µV/°C

Tamb 1 20
IIO Input offset current (2)
-40 °C < Tamb < +125 °C 100
nA
Tamb 86 160
IIB Input bias current (2)
-40 °C < Tamb < +125 °C 300
No load, output high, Vicm = 0 V 77 95
No load, output high, Vicm = 0 V,
125
-40 °C < Tamb < 125 °C
ICC Supply current µA
No load, output low, Vicm = 0 V 89 115
No load, output low, Vicm = 0 V,
135
-40 °C < Tamb < 125 °C
Source 51
ISC Short-circuit current mA
Sink 40
Isource = 4 mA 4.80 4.84
VOH Output voltage high V
-40 °C < Tamb < 125 °C 4.70
Isink = 4 mA 130 180
VOL Output voltage low mV
-40 °C < Tamb < 125 °C 250
Common mode rejection
CMRR 0 < Vicm < 5 V 79
ratio dB
SVR Supply voltage rejection ∆Vcc = 2 to 5 V 58 73
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
42 75
Propagation delay, low to overdrive = 100 mV
TPLH
high output level (3) Vicm = 0 V, f = 10 kHz, CL = 50 pF,
54 105
overdrive = 20 mV
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
45 75
Propagation delay, high to overdrive = 100 mV
TPHL ns
low output level (4) Vicm = 0 V, f = 10 kHz, CL = 50 pF,
55 95
overdrive = 20 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
TF Fall time 4
overdrive = 100 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
TR Rise time 4
overdrive = 100 mV

1. All values over the temperature range are guaranteed through correlation and simulation. No production test
is performed at the temperature range limits.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
3. Response time is measured 10%/90% of the final output value with the following conditions: inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive.
4. Response time is measured 10%/90% of the final output value with the following conditions: Inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive.

DS6029 - Rev 5 page 5/20

 TS3022
Electrical characteristic curves

3 Electrical characteristic curves

Figure 1. Current consumption vs. supply voltage Figure 2. Current consumption vs. supply voltage
(Vicm = 0 V, output high) (Vicm = Vcc output high)

115
84 VICM= 0V VICM=VCC
output HIGH -40oC output HIGH
110 -40oC
80
105
76
ICC (µA)

ICC (µ A)
72 100
+25oC +25oC

68 +125oC 95 +125oC

64 90

60 85
1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0 1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0
VCC(V) VCC(V)

Figure 3. Current consumption vs. supply voltage Figure 4. Current consumption vs. supply voltage
(Vicm = 0 V, output low) (Vicm = Vcc output low)

100 104
VICM= 0V VICM=VCC
96 100 output LOW
output LOW
-40oC
92 96

88 -40oC 92
ICC (µ A)
ICC (µ A)

o
84 +25 C 88 +25oC

80 84

76 80
+125oC +125oC
72 76

1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0 1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0
VCC(V) VCC(V)

Figure 5. Output voltage vs. source current, Vcc = 2 V Figure 6. Output voltage vs. sink current, Vcc = 2 V
2.0
0.5 VCC= 2V
1.9 output LOW

1.8 0.4
-40oC +125oC
1.7
VOUT (V)

0.3
VOUT (V)

+25oC
1.6 o
+25 C
0.2
1.5 -40oC
+125oC
0.1
1.4 VCC= 2V
output HIGH
1.3 0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
ISOURCE (mA) ISINK(mA)

DS6029 - Rev 5 page 6/20

 TS3022
Electrical characteristic curves

Figure 7. Output voltage vs. source current, Vcc = 3.3 V Figure 8. Output voltage vs. sink current, Vcc = 3.3 V

3.30 0.30
VCC= 3.3V
3.25 0.25 output LOW
-40oC
3.20
0.20
+125oC
3.15
VOUT (V)

VOUT (V)
0.15
+25oC
3.10
o
+25 C 0.10
3.05 -40oC
o
+125 C 0.05
3.00 VCC= 3.3V
output HIGH
2.95 0.00
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
ISOURCE (mA) ISINK(mA)

Figure 9. Output voltage vs. source current, Vcc = 5 V Figure 10. Output voltage vs. sink current, Vcc = 5 V

5.00 0.25
VCC= 5V
output LOW
4.95 0.20
-40oC

4.90 0.15 +125oC

VOUT (V)

VOUT (V)

+25oC
4.85 +25oC 0.10
-40oC
4.80 0.05
VCC= 5V
output HIGH +125oC
4.75 0.00
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
ISOURCE (mA) ISINK(mA)

Figure 11. Input offset voltage vs. temperature and Figure 12. Input bias current vs. temperature and input
common mode voltage voltage

1.4 100
VCC= 5V
VCC = 5V 50
1.2 VICM= 0V IIN-125oC IIN+125oC
0
1.0 -50
VVICM= 0V
Vio (mV)

IIB(nA)

0.8 -100
IIN+25oC IIN- 25oC
-150
0.6
-200
0.4 VICM= 5V
-250 IIN+-40oC IIN--40oC
0.2 -300

0.0 -350
-60 -40 -20 0 20 40 60 80 100 120 140 -100 -80 -60 -40 -20 0 20 40 60 80 100
Temperature (°C) VIN(mV)

DS6029 - Rev 5 page 7/20

 TS3022
Electrical characteristic curves

Figure 13. Current consumption vs. commutation Figure 14. Propagation delay (HL) vs. overdrive at
frequency Vcc = 2 V, Vicm = 0 V

600 100
VICM= 0V VCC= 2V
CLOAD= 50pF 90 VICM= 0V
500 TPHL
VCC= 5V 80
T= 125oC
400 TPHL
70
VCC= 3.3V T= 25oC TPHL
ICC (µA)

TP(nS)
300 60 T= -40oC
VCC= 2V 50
200
40
100
30

0 20
10k 100k 1M 0 10 20 30 40 50 60 70 80 90 100 110
Frequency (Hz) VOV(mV)

Figure 15. Propagation delay (HL) vs. overdrive at Figure 16. Propagation delay (LH) vs. overdrive at
Vcc = 2 V, Vicm = Vcc Vcc = 2 V, Vicm = 0 V

100 100
VCC= 2V VCC= 2V
90 VICM= VCC 90 VICM= 0V
TPLH
80 TPHL 80
T= 125oC
T= 125oC TPHL TPLH
70 70
T= 25oC TPHL TPLH
T= 25oC
TP (nS)

TP (nS)

60 T= -40oC 60 T= -40oC
50 50

40 40
30 30

20 20
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
VOV(mV) VOV(mV)

Figure 17. Propagation delay (LH) vs. overdrive at Figure 18. Propagation delay (HL) vs. overdrive at
Vcc = 2 V, Vicm = Vcc Vcc = 3.3 V, Vicm = 0 V
100
VCC= 2V 100 VCC= 3.3V
90 VICM= VCC VICM= 0V
90 TPHL
80 TPLH
o 80 T= 125oC TPHL
T= 125 C TPLH
70 T= 25oC TPHL
o TPLH 70
TP (nS)

T= 25 C
TP (nS)

60 o T= -40oC
T= -40 C 60
50 50
40 40
30 30

20 20
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
VOV(mV) VOV(mV)

DS6029 - Rev 5 page 8/20

 TS3022
Electrical characteristic curves

Figure 19. Propagation delay (HL) vs. overdrive at Figure 20. Propagation delay (LH) vs. overdrive at
Vcc = 3.3 V, Vicm = Vcc Vcc = 3.3 V, Vicm = 0 V

100 120
VCC= 3.3V VCC= 3.3V
90 110
VICM= VCC VICM= 0V
TPHL 100
80
T= 125oC 90 TPLH
TPHL
70 TPHL T = 125oC TPLH
T= 25oC 80 TPLH
T = 25oC
TP(nS)

TP(nS)
o
60 T= -40 C 70 T = -40oC
50 60
50
40
40
30 30
20 20
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
VOV(mV) VOV(mV)

Figure 21. Propagation delay (LH) vs. overdrive at Figure 22. Propagation delay (HL) vs. overdrive at
Vcc = 3.3 V, Vicm = Vcc Vcc = 5 V, Vicm = 0 V
100 110
VCC= 3.3V VCC= 5V
90 100 VICM= 0V
VICM= VCC TPHL
TPLH 90
80 T= 125oC TPHL
T = 125oC TPLH
80 TPHL
70 T = 25 Co TPLH T= 25oC
TP (nS)

T= -40oC
TP (nS)

o
T = -40 C 70
60
60
50
50
40
40
30 30
20 20
0 10 20 30 40 50 60 70 80 90 100 110 0 10 20 30 40 50 60 70 80 90 100 110
VOV(mV) VOV(mV)

Figure 24. Propagation delay (LH) vs. overdrive at

Vcc = 5 V, Vicm = 0 V
Figure 23. Propagation delay (HL) vs. overdrive at
Vcc = 5 V, Vicm = Vcc

110 120
VCC= 5V VCC= 5V
100 110
VICM= VCC VICM= 0V
90 100
TPHL TPLH
TPHL 90
80 T= 125 C o
o TPHL T = 125oC TPLH
T= 25 C 80 TPLH
TP (nS)

T= -40oC T = 25oC
TP (nS)

70 70 T = -40oC
60 60
50 50

40 40
30
30
20
20 0 10 20 30 40 50 60 70 80 90 100 110
0 10 20 30 40 50 60 70 80 90 100 110 VOV(mV)
VOV(mV)

DS6029 - Rev 5 page 9/20

 TS3022
Electrical characteristic curves

Figure 25. Propagation delay (LH) vs. overdrive at Figure 26. Propagation delay vs. temperature, Vcc = 5 V,
Vcc = 5 V, Vicm = Vcc overdrive = 100 mV
100 65
VCC= 5V VCC= 5V
90 VICM= VCC 60 VOV = 100mV
TPLH
80
T = 125oC TPLH 55
70 TPLH
T = 25oC
TP (nS)

TP (nS)
50
60 T = -40oC TPHL
45 VICM= 5V
50 TPLH
40 40 TPHL VICM= 5V
TPLH VICM= 0V
30 35
VVICM= 0V
20 30
0 10 20 30 40 50 60 70 80 90 100 110 -40 -20 0 20 40 60 80 100 120
VOV(mV) Temperature (°C)

Figure 27. Propagation delay vs. common mode voltage, Vcc = 5 V

70

TPLH TPHL
60 VOV= 20mV VOV= 20mV

50
TP (nS)

40
TPLH TPHL
30 VOV= 100mV VOV= 100mV
VCC = 5V
Temp.= 25°C
20
-0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VICM(mV)

DS6029 - Rev 5 page 10/20

 TS3022
Application recommendation

4 Application recommendation

When high speed comparators are used, it is strongly recommended to place a capacitor as close as possible to
the supply pins. Decoupling has two main advantages for this application: it helps to reduce electromagnetic
interference and rejects the ripple that may appear on the output.
A bypass capacitor combination, composed of 100 nF in addition to 10 nF and 1 nF in parallel is recommended
because it eliminates spikes on the supply line better than a single 100 nF capacitor. Each millimeter of the PCB
track plays an important role. Bypass capacitors must be placed as close as possible to the comparator supply
pin. The smallest value capacitor should be preferably placed closer to the supply pin.
In addition, important values of input impedance in series with parasitic PCB capacity and input comparator
capacity create an additional RC filter. It generates an additional propagation delay.
For high speed signal applications, PCB must be designed with great care taking into consideration low resistive
grounding, short tracks and quality SMD capacitors featuring low ESR. Bypass capacitor stores energy and
provides a complementary energy tank when spikes occur on the power supply line. If the input signal frequency
is far from the resonant frequency, impedance strongly increases and the capacitor loses bypassing capability.
Placing different capacitors with different resonant frequencies allows a wide frequency bandwidth to be covered.
It is also recommended to implement an unbroken ground plane with low inductance.

Figure 28. High speed layout recommendation

DS6029 - Rev 5 page 11/20

 TS3022
Package information

5 Package information

In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages,
depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product
status are available at: www.st.com. ECOPACK is an ST trademark.

DS6029 - Rev 5 page 12/20

 TS3022
SO-8 package information

5.1 SO-8 package information

Figure 29. SO-8 package outline

Table 6. SO-8 package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 1.75 0.069
A1 0.10 0.25 0.04 0.010
A2 1.25 0.049
b 0.28 0.48 0.011 0.019
c 0.17 0.23 0.007 0.010
D 4.80 4.90 5.00 0.189 0.193 0.197
E 5.80 6.00 6.20 0.228 0.236 0.244
E1 3.80 3.90 4.00 0.150 0.154 0.157
e 1.27 0.050
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
L1 1.04 0.040
k 0 8° 1° 8°
ccc 0.10 0.004

DS6029 - Rev 5 page 13/20

 TS3022
MiniSO8 package information

5.2 MiniSO8 package information

Figure 30. MiniSO8 package outline

Table 7. MiniSO8 mechanical data

Dim. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 1.1 0.043
A1 0 0.15 0 0.006
A2 0.75 0.85 0.95 0.03 0.033 0.037
b 0.22 0.4 0.009 0.016
c 0.08 0.23 0.003 0.009
D 2.8 3 3.2 0.11 0.118 0.126
E 4.65 4.9 5.15 0.183 0.193 0.203
E1 2.8 3 3.1 0.11 0.118 0.122
e 0.65 0.026
L 0.4 0.6 0.8 0.016 0.024 0.031
L1 0.95 0.037
L2 0.25 0.01
k 0° 8° 0° 8°
ccc 0.1 0.004

DS6029 - Rev 5 page 14/20

 TS3022
Ordering information

6 Ordering information

Table 8. Ordering information

Order code Temperature range Package Packing Marking

TS3022IDT SO-8 3022I

TS3022IST -40 to 125 °C Tape and reel K521
MiniSO-8
TS3022IYST (1) K520

1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001
and Q 002 or equivalent.

DS6029 - Rev 5 page 15/20

 TS3022

Revision history

Table 9. Document revision history

Date Revision Changes

Initial release. The information contained in this datasheet was previously included
in the TS3021-TS3022 datasheet (revision 4 dated October 2007). The single
29-Jan-2009 1 version (TS3021) and dual version (TS3022) have now been split into two
separate datasheets. Refer to the TS3021 revision 5 for a complete history of
changes.
Modified ESD tolerances in Table 1: Absolute maximum ratings. In Table 3, Table
4 and Table 5: – modified VIO typical value and maximum limits. – modified IIB
typical value. – modified ICC typical values and corrected maximum limits. –
25-Jun-2009 2
modified ISC typical values. – modified VOH and VOL typical values. – modified
CMRR and SVR typical values. – modified TPHL and TPLH typical values. –
modified note 3. – added note 4. Modified all curves.
Updated features and applications in cover page.
07-Dec-2017 3
Updated Section 6: "Ordering information".
26-Mar-2019 4 Added new CDM parameter in Table 1. Absolute maximum ratings (AMR).
22-Oct-2020 5 Updated Table 8. Ordering information.

DS6029 - Rev 5 page 16/20

 TS3022
Contents

Contents
1 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Electrical characteristic curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Application recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
5 Package information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
5.1 SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 MiniSO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

DS6029 - Rev 5 page 17/20

 TS3022
List of figures

List of figures
Figure 1. Current consumption vs. supply voltage (Vicm = 0 V, output high) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 2. Current consumption vs. supply voltage (Vicm = Vcc output high) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 3. Current consumption vs. supply voltage (Vicm = 0 V, output low). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 4. Current consumption vs. supply voltage (Vicm = Vcc output low). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5. Output voltage vs. source current, Vcc = 2 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 6. Output voltage vs. sink current, Vcc = 2 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 7. Output voltage vs. source current, Vcc = 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 8. Output voltage vs. sink current, Vcc = 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 9. Output voltage vs. source current, Vcc = 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 10. Output voltage vs. sink current, Vcc = 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 11. Input offset voltage vs. temperature and common mode voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 12. Input bias current vs. temperature and input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 13. Current consumption vs. commutation frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 14. Propagation delay (HL) vs. overdrive at Vcc = 2 V, Vicm = 0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 15. Propagation delay (HL) vs. overdrive at Vcc = 2 V, Vicm = Vcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 16. Propagation delay (LH) vs. overdrive at Vcc = 2 V, Vicm = 0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 17. Propagation delay (LH) vs. overdrive at Vcc = 2 V, Vicm = Vcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 18. Propagation delay (HL) vs. overdrive at Vcc = 3.3 V, Vicm = 0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 19. Propagation delay (HL) vs. overdrive at Vcc = 3.3 V, Vicm = Vcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 20. Propagation delay (LH) vs. overdrive at Vcc = 3.3 V, Vicm = 0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 21. Propagation delay (LH) vs. overdrive at Vcc = 3.3 V, Vicm = Vcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 22. Propagation delay (HL) vs. overdrive at Vcc = 5 V, Vicm = 0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 23. Propagation delay (HL) vs. overdrive at Vcc = 5 V, Vicm = Vcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 24. Propagation delay (LH) vs. overdrive at Vcc = 5 V, Vicm = 0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 25. Propagation delay (LH) vs. overdrive at Vcc = 5 V, Vicm = Vcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 26. Propagation delay vs. temperature, Vcc = 5 V, overdrive = 100 mV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 27. Propagation delay vs. common mode voltage, Vcc = 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 28. High speed layout recommendation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 29. SO-8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 30. MiniSO8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DS6029 - Rev 5 page 18/20

 TS3022
List of tables

List of tables
Table 1. Absolute maximum ratings (AMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table 2. Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table 3. Electrical characteristics at VCC+ = 2 V, VCC- = 0 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified) 3
Table 4. Electrical characteristics at VCC+= 3.3 V, VCC- = 0 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified)
................................................................................ 4
Table 5. Electrical characteristics at VCC = 5 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified) . . . . . . . . . 5
Table 6. SO-8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 7. MiniSO8 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 8. Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 9. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DS6029 - Rev 5 page 19/20

 TS3022

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service
names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved

DS6029 - Rev 5 page 20/20