Thermoelectric Devices

Cooling and Power Generation

Prof. Dr. Yehea Ismail Ahmed Al-Askalany

Center of Nanoelectronics and Devices
The American University in Cairo
Cairo, Egypt
[email protected], [email protected]

Abstract – Thermoelectricity is the direct conversion of

temperature gradient to electric voltage, and vice-versa. II. THERMOELECTRIC EFFECTS
There are several potential applications of As mentioned in the introduction, Thermoelectricity is
thermoelectricity, ranging from clean noiseless cooling, to described by three thermoelectric effects.
waste-power harvesting in automotives. The performance The “Seebeck Effect” is the conversion of temperature
of thermoelectric devices is still a challenge, and many gradient across the junctions of two dissimilar metals to
approaches have been researched to overcome such electrical voltage in the range of millivolts per Kelvin
obstacle. This paper seeks to give an overview of the difference. The effect is non-linear with temperature, and
thermoelectric phenomenon, the bulk semiconductor depends on absolute temperature, type and structure of
thermoelectric devices, and the new ways to increase materials. The Seebeck coefficient S is the amount of voltage
performance of thermoelectric devices using new material difference ∆Vgenerated for an applied temperature
structures and going to low-dimensional materials. difference ∆T.

Keywords – Thermoelectric Devices, Thermoelectricity, 𝑆 = ∆𝑉 ∆𝑇 (1)

Thermoelectric Cooler, Peltier Cooler, Thermoelectric
Generator. The voltage difference V, then can be calculated using the
following equation,

I. INTRODUCTION Th

Thermoelectricity is the direct conversion of temperature V= SB T -SA T dT (2)

Tc
gradient to electrical potential difference. The phenomenon
discovery dates back to 1800s, with many potential The “Peltier Effect” is that a current flow causes a
applications now and in the future, but also with a challenge temperature gradient across the junctions of two dissimilar
to increase thermoelectric devices’ performance. The metals. The heat transfer is in the same direction of charge
phenomenon is described by three effects. The Seebeck effect carriers. The thermal current density q is given by the
-discovered by Thomas Seebeck- in 1821 is the conversion of following equation, where ᴨ and j are the Peltier coefficient,
temperature difference into electrical voltage. The Peltier and electrical current density.
effect -discovered by Jean Peltier in 1934- is the conversion
𝑞 =ᴨ𝑗 (3)
of voltage into temperature gradient. And the Thomson effect
–discovered by William Thomson in 1851- is the heat flow in The “Thomson Effect” is the heat flow across a conductor,
a conductor with terminals held at different temperatures, due with terminals at different temperatures, due to current flow.
to current flow. The heat flow is given by:
Thermoelectric devices can be used for heating/cooling
𝑑𝑄 𝑑𝑇
purposes, or for power generation. The applications for = 𝜇𝐼 (4)
thermoelectric devices can span different areas and industries. 𝑑𝑥 𝑑𝑥
Waste-heat energy harvesting in automotives is one The Thomson effect is the only measurable effect among
promising application for such technology [1]. Remote space the three thermoelectric effects, for a certain material, since
missions use thermoelectric devices for power generation. the two other effects are related to pairs of materials.
The main challenge for thermoelectric devices’ design is Thomson/Kelvin relationship described in the following
the device performance, and the compromise between equations relates the three thermoelectric effects.
material parameters to increase it. The attempts to increase
the performance of thermoelectric materials and devices are ᴨ = 𝑆𝑇 (5)
many, from material parameters optimization, to using going
to new material structures, and low-dimensional 𝑑𝑆
𝜇=𝑇 (6)
thermoelement [1]. 𝑑𝑇
ᴨ, S, T, µ are the Peltier coefficient, the Seebeck
coefficient, the absolute temperature, and the Thomson
coefficient.

1
 III. THERMOELECTRIC FIGURE OF MERIT IV. BULK SEMICONDUCTOR TEC DEVICES
The performance of a thermoelectric device is indicated by Thermoelectric cooling device (TEC), or Peltier cooler,
the figure of merit (FOM) ZT, it is a dimensionless quantity, depends in its operation on the Peltier effect described in the
which is given by: introduction. A current flow in a closed circuit of two
dissimilar materials causes a temperature gradient across the
𝐺𝑆 2 𝑇 junctions.
𝑍𝑇 = (7)
𝐾𝑙 + 𝐾𝑒 In bulk thermoelectric coolers, the semiconductor material
G,𝐾𝑙 , 𝐾𝑒 and T are electrical conductivity, lattice thermal is put between two conductor plates. The charge carriers are
conductivity, electronic thermal conductivity, and absolute average responsible for the process of heat transfer, due to the
temperature. different energies required for their movement in the
For higher ZT, a large Seebeck coefficient and electrical semiconductor material and the conductor material. The
conductivity, and small thermal conductivity are required. thermal current is in the same direction as charge carriers, as
Thermal conductivity decreases the FOM, since it leads to shown in fig. 3.
undesired thermal exchange between hot and cold sides of a For an n-type thermoelement, electrons move freely in the
thermoelectric device. conductor, and when they reach n-type material, they require
The compromise to increase ZT is shown in fig. 1, more energy, which is absorbed from the surrounding
Increasing the carrier concentration in order to increase environment. When moving from n-type back to the
electrical conductivity, also gives rise to thermal conductor, heat is released. For a p-type thermoelement,
conductivity, and the Seebeck coefficient starts to decrease electrons entering semiconductor fill a hole, this drop in
with higher thermal conductivity, due to lack of the ability of energy level is associated with heat release. And back to the
the material to maintain higher temperature gradient. conductor, electrons are back to a higher level of energy by
Bi2 Te3 Is the most commonly used semiconductor material absorbing heat.
because of its relatively high FOM ZT=1 at 300°K. For more heat flow more thermoelectric elements are
required. Different approaches were implemented using
single type arrangements. A configuration of multiple single-
type thermoelements connected in parallel electrically and
thermally, Fig. 4.a. This configuration requires low voltage
with high current, which was impractical commercially.
Another configuration was a set of single-type
thermoelements connected parallel thermally and in series
electrically, fig. 4.b. This would allow for larger heat transfer,
but interconnects shorting the conductor surfaces limited the
process of heat transfer.
The solution for the mentioned problem is using both n-
type and p-type thermoelements to form a couple. This
configuration is called a “Peltier Thermocouple”, shown in
fig 4.c.

Figure 1: shows the FOM for some p-type semiconductor

[1]
materials .

Figure 3: N-type and p-type thermoelements.

Figure 4: a) n-type parallel TEC. b) n-type series TEC. c) Peltier

[1] thermocouple.
Figure 2: FOM for p-type materials .

2
 V. THE THERMOPILE Table 1: TEC1-12710 module parameters.

Using more thermocouples connected in series increases Parameter Value

heat transfer. A set of alternating thermocouples are Max Current 10 Amps
connected in series electrically and in parallel thermally. Max Voltage 15.4 Volts
Such configuration is called the “Peltier Thermopile”, fig. 5. Seebeck Coefficient 0.0513
To find the different parameters of a thermopile, a set of Internal Resistance 1.1909 Ohms
equations are given [5], relating those parameters to the FOM (Z) 0.0026
number of thermoelements in the thermopile and material Thermal Conductivity 0.8757
parameters. The Seebeck coefficient of the total number n of
thermocouples is given by,
VI. THERMOELECTRIC COOLER MATLAB SIMULATION
In order to account for thermoelectric coolers in design, a
𝑇ℎ
model [3] of the cooler should be made, relating its electrical
𝑆=𝑛 𝑆𝑝 − 𝑆𝑛 𝑑𝑇 (8)
𝑇𝑐 and thermal characteristics to manufacturer’s data sheet for
the device. A model that defines the required current to
The device resistance and thermal conductance (of materials achieve certain temperature difference is given as follows,
and interconnects) are approximated by,
𝜌𝑛 𝑙 𝜌𝑝 𝑆 𝑇𝐻 − ∆𝑇 − 𝑆 𝑇𝐻 − ∆𝑇 2 − 2∆𝑇 𝑍 (17)
𝑅 = 𝑛( + + 𝑅𝑙 ) (9) 𝐼=
𝐴𝑛 𝐴𝑝 𝑅
𝐾𝑛 𝑙 𝐾𝑝 And the Voltage required,
𝐾 = 𝑛( + + 𝐾𝑙 ) (10)
𝐴𝑛 𝐴 𝑝 𝑉 = 𝑉𝑚𝑎𝑥 − 𝑆 𝑇𝐻 − ∆𝑇 − 2∆𝑇 𝑍
2 (18)
The heat transferred is the sum of the Peltier, Fourier, and Given the manufacturer’s data for the thermoelectric
Joule heat terms, cooler “TEC1-12710” in the table 1[3], A Matlab code was
1 written to demonstrate the current and voltages required for a
𝑄 = 𝐼𝑆𝑇 − 𝐾∆𝑇 − 𝐼 2 𝑅 (11) range of temperature differences.
2 The hot side temperature was kept constant at 300°K, and
When operating as a thermoelectric cooler. Maximum varying the cold side temperature from 230°K to 300°, and
current, maximum heat pumping, maximum temperature plotting the required current and voltage versus cold side
difference are given by, temperature.
𝐼𝑚𝑎𝑥 = 𝑆𝑇𝑐 𝑅, (12) The results shown in fig. 6 shows that the amount of
current/voltage required is inversely proportional to the
temperature difference desired, between the hot and cold
𝑄𝑚𝑎𝑥 = 𝑆 2 𝑇𝑐2 2𝑅, (13)
sides of the device.
∆𝑇𝑚𝑎𝑥 = 𝑍𝑇𝑐2 2, (14)

And the device’s FOM is,

𝑍𝑇 = 𝑆 2 𝑇 𝐾𝑅 . (15)

When operating as a thermoelectric generator. The efficiency

is approximated with,

∆𝑇 1 + 𝑍𝑇 − 1
𝜂= (16)
𝑇ℎ 1 + 𝑍𝑇 + 𝑇𝑐
𝑇 ℎ

For a TEG, the efficiency increases with the increase in

temperature difference, approaching Carnot efficiency limit.

Figure 5: Peltier Thermopile. Figure 6: Tc-I and Tc-V of TEC model.

3
VII. NEW MATERIALS FOR THERMOELECTRIC DEVICES
The use of quantum well structures and thin films for
thermoelectric devices is the current research efforts in order
to increase the performance of thermoelectric materials and
devices. For example, alternating layers of Sb2Te3 and BiTe3
are used to make thin films used in thermoelectric coolers.
Such new material dimensions and arrangements allowed for
power densities up to 100W/𝑐𝑚2 .
The use of thermoelectrical wires in the nanometer scale
grown inside of a nanoporous aluminum matrix is used in
order to improve electrical and thermal parameters beyond
bulk materials.
[1]
Figure 8: Doping and WT vs. S
Structures like alternating thin layers of quantum wells are
used, which enhances the electrical and thermal parameters of
the material. A device that consists of alternating layers of Si
(barrier) and SiGe (quantum well) is shown in fig. 7. The
structure was simulated using SILVACO TCAD, showing
improved characteristics over bulk semiconductor
thermoelectric devices [1].
The use of quantum well in semiconductor thin-layer
materials affects materials parameters, the parameters of such
structures is different from bulk materials, showing
improvement in thermoelectric performance.
Figure 8 shows the effect of doping level and quantum
well thickness on the Seebeck coefficient of the material. And
[1]
fig. 9 shows the effect of doping level and well thickness on Figure 9: Doping and WT vs. ZT
the numerator of ZT (FOM). Fig. 10 shows the change in
thermal conductivity with size in ultra-thin crystal Si. Fig. 11
shows the effect of doping level and barrier thickness on the
conductivity.

[1]
Figure 10: Size vs. Thermal conductivity

[1]
Figure 7: Si/SiGe Quantum-well thin film thermoelectric device

[1]
Figure11: Barrier thickness vs. electrical conductivity

4
 VIII. CONCLUSION. REFERENCES
Thermoelectric devices have great potential for many [1] Shaoting Hu, “Exploring Si/SiGe Quantum-Well Thin-Film
Thermoelectric Devices using TCAD Simulation”, Electrical
applications, in different industries and fields. The
and Microelectronic Engineering Department, Rochester
thermoelectric coolers offer an environment friendly and very Institute of Technology, 2012.
silent solution, it could be used in cars, homes, and food [2] Chakib Alaoui, “Peltier Thermoelectric Modules Modeling
industry. Thermoelectric generators can be utilized in power and Evaluation”, International Journal of Engineering, vol. 5,
Issue 1, 2011.
harvesting in automotives, were excess thermal waste-energy [3] Haun-Liang Tsai, Jium-Ming Lin, “Model Building and
is found. Simulation of Thermoelectric Module Using
Matlab/Simulink”, Journal of Electronic Materials, Vol. 39,
The physics of thermoelectric devices is well known to us, No. 9, 2010. DOI: 10.1007/s11664-009-0994-x
and the tradeoff and compromise in increasing the [4] Abhijeet Paul, “Thermoelectric effects in ultra-scaled
performance of thermoelectric materials is not an easy task, semiconductor devices: Role of electronic and lattice
properties”, Network for Computational Technology and
the thermal and electrical parameters of a thermoelectric School of Electrical and Computer Engineering, Purdue
material are strongly entangled, and the seek for optimization University, nanoHUB Presentation.
of on parameters, directly affects another parameter in an [5] “Thermoelectrics: Thermoelectric Engineering”, California
undesired way. Institute of Technology, online website.

Bulk semiconductors were firstly and still used for the

manufacturing of thermoelectric devices; many assemblies
were thought of and tried. The thermopile which consists of
alternating thermocouples of n-type and p-type thermoelents
is the best way to have larger assemblies of bulk
semiconductor thermoelectric devices. The FOM of merit of
thermoelectric cooler and the efficiency of thermoelectric
devices not only depend on material parameters and
temperature difference, but also on the absolute average
temperature the device operates in, making different materials
suitable for different operating temperatures.
The introduction of nanowires thermoelectric wires and
structures with quantum wells has shown a promising
improvement in the performance of such new devices.
Future research investigating the integration of low-
dimensional material thermoelectric devices with solar
energy materials would lead to a solution for the thermal
waste-energy generated in solar power harvesting devices.
Even if it could be possible to design a device that operates
for both purposes, solar and thermal power harvesting, this
would be great to compensate for the low power efficiency of
both types of devices.
The work in simulation of quantum well thermoelectric
devices using TCAD will be my starting point to get a deeper
understanding of the tradeoffs in material parameters. And it
will offer me an opportunity for future research in the subject,
with the intention to find new ideas in materials and device
design.