Lcd-Sw900 Instructions: 1. Shell's Size and Material

LCD-SW900 INSTRUCTIONS
1. Shell’s Size and Material

The shell’s material is ABS. LCD screen is made of imported high hardness acrylic, and the
hardness is equal to the tempered glass.
Front View Side View
Side View of the Holder Optional size: 22.2mm, 25.4mm
2. Working Voltage and Mode of Connection

2.1 Working Voltage: DC24V 36V 48V (set by the meter), other voltage could be customized.
2.2 Mode of Connection:
Standard Connectors Line Sequence:
Red Line (D+): Power Positive

Black Line (GND): Power Negative
Blue Line (DS): Controller’s electric door lock
Brown Line (DD+): Lighting control’s Positive ( If the controller’s software and hardware support
the lighting control, do not need connect this line)
Green Line (RX): Receiving communication
Yellow Line (TX): Sending communication
White Line (GND): Lighting control’s Negative
Extended Functions: PWM Assistance grades control, Independent external speed sensor
3. Functions
3.1 LCD Display
Speed indicator, PAS grades indicator, Battery indicator, Error indicator, Single Trip Distance and
Total Distance, Headlight indicator.
3.2 Parameters Setting
Power on/off, Headlight on/off, 6KM/H Cruise control, Wheel size, Max speed setting,
Auto stand-by and sleep mode setting, Background luminance setting, Working voltage setting.
3.3 Communication Protocol: UART
4. All contents on the screen

4.1 Headlight
4.2 Power status
4.3 Multi-functions
Total Distance(ODO), Single Trip Distance(TRIP), Error Code(Error), Wattage(WATT),
Maintenance(Maintain), DST TO GO(Unused temporarily)
4.4 E-Bike Mode
Economic mode(ECO), Standard mode(STD), Powerful model(POWER), Hand speed-control

model(SPEEDHANDLE), Walk assisted model(WALK)
4.5 Speed display

Maximum speed(MAX), Average speed(AVG)
MPH, KM/H are both optional.
According Wheel size and signal data, the meter could figure out the real speed.
4.6 Error display
Meaning of Error Code:

Error Code Error Status Notes
0 Normal Status
1 Save
2 Brakes
3 PAS problem(a riding mark) not implemented
4 6KM/H cruising
5 Real-time cruising
6 Battery is under-voltage
7 Motor’s problem
8 Throttle’s problem
9 Controller’s problem
10 Communication Receiving problem
11 Communication Sending problem
12 BMS Communication problem
13 Headlight problem
4.7 PAS grades
PAS Status (0-9 grades), Cruise mark

4.8 Parameters setting
P01 Background luminance. 1 is the darkest, 3 is the brightest
P02 Unit of the mileage. 0 is KM, 1 is MILE
P03 Voltage grades. 24V, 36V, 48V. The original voltage is 36V.
P04 Sleep time. 0 is without sleep, other numbers stand for the sleep time (1-60 min).
P05 PAS grades.
0, 3 grades mode: 1 grade 2V, 2 grade 3V, 3 grade 4V
1, 5 grades mode: 1 grade 2V, 2 grade 2.5V, 3 grade 3V, 4 grade 3.5V, 5 grade 4V
P06 Wheel size. Unit: inch. Precision: 0.1
P07 Speed measuring magnet. Range: 1-100
P08 Speed limit. Range: 0-50km/h, 50 means without limit
No-Communication Status (controlled by the meter): when the real speed is over the ones
we set, the meter would shut off PWM output; when less than the speed we set, the meter
would turn on PWM output automatically, the driving speed would be ±1km/h; (Speed limit
is for PAS, not for Throttle)
Communication Status (controlled by the controller): The driving speed keeps same with the
ones we set. Random error: ±1km/h. (Speed limit is for both PAS and Throttle)
Notes: These data are based on KM. When changing KM to Mile, the speed value on the
screen would convert to correct Miles automatically, but if you do not change the setting of
speed limit from KM to Mile, it would be different from the real speed limit in Mile.
P09 Zero start & Non-zero Start. 0 is Zero Start, 1 is Non-zero Start
P10 Driving mode.
0 is driven by PAS. Throttle is useless at this time.
1 is driven by Throttle. PAS is useless at this time.
2 is driven by PAS & Throttle. Throttle is useless at Zero Start status.
P11 PAS sensitivity. Range: 1-24
P12 PAS start strength. Range: 0-5
P13 PAS magnet type. There are 3 types: 5, 8, and 12.
P14 The Current-limiting of Controller. The original Current is 12A. Range:1-20A
P15 Not implemented now.
P16 Reset ODO. Long press for 5s, ODO could be reset.
5. Button Introductions
5.1 During riding, need change PAS/Speed grades, shortly press
5.2 During riding, need change data in Multi-function Area, shortly press ;
Long press , could switch status between MODE and ON/OFF;

Long press as a compound button, is mainly used for parameter setting, which could reduce
misoperation due to complicated operation.
(No compound button with short-time press, because it’s difficult to operate.)
5.3 Specific operation explanations

5.3.1 Change PAS grade
Suppose it’s PAS mode now,
shortly press , PAS grade +1
shortly press , PAS grade -1

5.3.2 Shift the speed display
Long press + , to shift the way of speed display

5.3.3 ON/OFF 6KM/H cruising, ON/OFF Headlight, Reset ODO
When e-bike stops, long press to enter 6KM/H cruising mode. Stop
pressing to exit the cruise mode;
Long press to turn ON/OFF Headlight;
At P16, long press for 5s to reset ODO.

5.3.4 ON/OFF the screen
Long press to turn ON/OFF the screen.

5.3.5 Change data in multi-function Area
Shortly press to change data.

5.3.6 Parameters setting
Long press + to start setting parameters, such as wheel

size(inch), background luminance… (Refer to P01-P16)
On the setting interface, shortly press , or to plus/minus

value. Parameters would be shining after modifying, choose the ones you prefer,
a. Long press to save the value, the shining would stop.
b. Shortly press to shift to the next parameter, and to save current values
at the same time.
c. Press + to exit setting parameters and to save values. If

not press these buttons, it would exit and save parameters modified automatically 10s
later.

Lcd-Sw900 Instructions: 1. Shell's Size and Material

Uploaded by

Copyright:

Available Formats

Lcd-Sw900 Instructions: 1. Shell's Size and Material

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lcd-Sw900 Instructions: 1. Shell's Size and Material

Uploaded by

Copyright:

Available Formats

LCD-SW900 INSTRUCTIONS

1. Shell’s Size and Material

Front View Side View

Side View of the Holder Optional size: 22.2mm, 25.4mm

2. Working Voltage and Mode of Connection

Standard Connectors Line Sequence:

Red Line (D+): Power Positive

4. All contents on the screen

4.2 Power status

Economic mode(ECO), Standard mode(STD), Powerful model(POWER), Hand speed-control

4.5 Speed display

4.6 Error display

Meaning of Error Code:

4.7 PAS grades

PAS Status (0-9 grades), Cruise mark

5.1 During riding, need change PAS/Speed grades, shortly press

Long press , could switch status between MODE and ON/OFF;

5.3 Specific operation explanations

shortly press , PAS grade +1

shortly press , PAS grade -1

Long press + , to shift the way of speed display

Long press to turn ON/OFF Headlight;

At P16, long press for 5s to reset ODO.

Long press to turn ON/OFF the screen.

Shortly press to change data.

Long press + to start setting parameters, such as wheel

On the setting interface, shortly press , or to plus/minus

a. Long press to save the value, the shining would stop.

c. Press + to exit setting parameters and to save values. If

You might also like