Nanostructured electronic & magnetic

materials

Abstract: Research and development in nanostructured materials is

one of the most intensely studied areas in science. As a result of
concerted R & D efforts, nanostructured electronic and magnetic
materials have achieved commercial suc-cess. Specific examples of
novel industrially important nanostructured electronic and magnetic
materials are provided. Advantages of nanocrystalline magnetic mate-
rials in the context of both materials and devices are discussed.
Several high tech-nology examples of the use of nanostructured
magnetic materials are presented. Methods of processing
nanostructured materials are described and the examples of sol gel,
rapid solidification and powder injection moulding as potential
processing methods for making nanostructured materials are outlined.
Some opportunities and challenges are discussed.

Keywords. Nanomaterials; electronic materials; magnetic materials;

magnetic media; materials processing.

1. Introduction

Nanostructured materials (nanomaterials) are materials possessing at least one

length scale on the order of a billionth of a meter. They manifest extremely
fascinating and useful properties, which can be exploited for a variety of
structural and non-structural applica-tions (Inoue 2001). Nanostructured
materials can possess improved properties such as high strength, improved
hardness, ductility in normally brittle materials, wear-resistance, erosion-
resistance, corrosion-resistance and higher chemical activity (Edelstein &
Cammarata 1998). Nanomaterials can be much more formable than their
conventional, commercially avail-able counterparts. Research on
nanomaterials research literally exploded in mid-1980's in the US.
Nanomaterials have numerous commercial and technological applications in
areas like analytical chemistry, drug delivery, bioencapsulation, and in
electronic, magnetic, optical and mechanical devices. Although there is much
literature available on nanomaterials, in this paper, specific examples are
chosen which are considered to be of near-term commercial value. The paper
discusses the applications of nanomaterials in electronics and magnetic
devices, and finally a summary of processing methods is presented.

2 Nanostructured magnetic materials

Many of our modern technological devices rely on magnetism and magnetic

materials; these include electrical power generators and transformers, electric
motors, computers, and com-ponents of sound and video reproduction systems
(DeCristofaro 1998). Novel nanomagnetic materials are interesting from the
point of view of the relationship between microstruc-tural features and
magnetic properties. Such features include particle size and distribution,
chemical inhomogeneities, crystalline defects, crystallographic texture
examples being (a) nanocrystalline soft magnetic materials produced from
amorphous precursors, (b) two-phase nanoparticles with high moment cores
and high resistivity ferrite shells, and (c) spring exchange magnetic materials
(Kneller 1991; Wu et al 2001). Areas of topical interest include soft and hard
magnets, hard magnetic nanoprticles, magnetic recording media and magnetic
multilayers.

2.1 Basic principles guiding the synthesis of nanomagnetic materials

All ferromagnetic materials below the Curie temperature are composed of
small-volume regions, called domains, in which there is a mutual alignment in
the same direction of all magnetic dipole moments. Within these domains, the
spontaneous magnetization present is equal to the saturation magnetization of
the material, and so the individual domains are fully magnetized at all times.
In the absence of an applied field, there is no net magnetic moment or field
generated by the material because the magnetization direction of each domain
is randomly oriented. During magnetization of the material, domains whose
magnetization directions have a component in the direction of the applied field
will grow at the expense of those that do not. Once all the unfavorably
oriented domains have been eliminated by domain wall movement, the
magnetization direction of the single domain that remains will be rotated so as
to be parallel to that of the applied field and saturation is thus achieved. As the
magnetic field is reduced by reversal of field direction, the curve does not
retrace its original path. A hysteresis effect is produced and forms a hysteresis
loop, this loop is a key tool in the quantitative analysis of permanent magnet
performance. These loops are a graphical representation of the relationship
between an applied magnetic field and the resulting induced magnetization
within a material. The field that is generated by the magnetized material . (Bi)
when added to that of the applied field .(H )is known as the normal induction
.(Bn) or simply
B. Since this induction has two components, it is defined as:
 B = Bi + H
The loops show the properties of the magnetic material as it is magnetized and
demagnetized. When a magnetic field is applied to unmagnetized material, the
intrinsic induction .Bi is established within it, parallel to the applied field. If
H is sufficiently strong, the magnet will become fully magnetized at the
saturation flux density .Bsat When the field is reduced to zero, the magnet
returns to the residual value or remanence .Br , as long as the magnet is within
a closed magnetic circuit. Some of these magnetic properties can be improved
with nanostructured magnetic material and thus the next section will discuss
nanostructured magnetic materials.

2.2 Nanostructured magnetic materials

Magnetic nanoparticles show a variety of unusual magnetic behaviour
compared to bulk mate-rials, mostly due to surface/interface effects, including
symmetry breaking, electronic envi-ronment/charge transfer, and magnetic
interactions. Futhermore, since nanophase particles can be as much as 50%
surface material, new magnetic properties characteristic of surfaces and
interfaces become important and may be of practical value.

3 Some applications of nanostructured magnetic materials

3.3a Storage applications:
The route to progress in memory technology is cost reduction and the
development of ever faster, more compact, and less power consuming memory
sys-tems, with greater storage capacity. Theory shows that all these benefits
can be obtained by reducing the size of the basic storage cell, hence it is
natural to suppose that nanotechnol-ogy will eventually play a fundamental
role. However, it is imperative that the system must also include a means for
writing and reading the cells efficiently. This is the most demanding aspect of
memory design. For instance, very compact memories based on scanning
tunnelling microscopy employs storage cells approaching the size of a single
atom. One formidable chal-lenge to this is designing sufficiently fast and
reliable read/write mechanisms. One probable route by which nanostructure
research could lead to a successful memory technology would be via
nanoelectronics research resulting in the development of an ultrahigh-density,
VLSI technology

3.3b Giant magneto resistance (GMR) recording head:

Magnetic recording essentially involves detecting changes in the direction of
magnetization in the storage medium. Small magnetic fields immediately
above the regions of magnetization changes are associated with this
divergence. These stray fields are read by inducing signals or resistance
changes in the head as the storage medium is moved past them. This is called
magnetoresistive effect, and
it is useful for sensing magnetic fields such as those in the magnetic bits of
data stored on a computer hard drive.
In order to store the magnetic transitions at high densities (e.g. 10 4 cm−1),
several constraints are imposed on the storage media and on the write and read
heads. Just take the case for storage media. With a high storage density, the
distance between magnetization reversals become very small. This produces
strong demagnetising fields on the stored `bit'. For stable storage, the coercive
force, must be high enough to withstand these demagnetising stray fields.
Another consideration is to ensure sufficient stray field for detection of the
transition, a high remanence is thus required. A storage medium with both
high coercive force and saturation magnetization would seem to be required.
High permeability and high data rates (> 100 MHz) place additional
constraints on the write head materials, e.g., eddy currents need to be avoided.
Nanostructured structures promise to solve all these constraints on media and
read heads. Specially prepared layers of nanometer-thick magnetic and non-
magnetic films were found to exhibit the giant magnetoresistance (GMR)
effect. In 1991, it was demonstrated by IBM Almaden research center that the
GMR effect could be observed in easily made samples. It also discovered that
a special kind of GMR structure, a spin valve, could sense very small
magnetic fields. A new era involving the use of GMR in the read heads for
magnetic disk drives has begun.
In the spin valve GMR head shown in figure 1, the copper spacer layer is
about 2 nm thick and the Co GMR pinned layer is about 2.5 nm thick. It is
important to control these layers thickness with atomic precision. This novel
read head has extended magnetic disk information storage from 1 to ~ 20
Gbits in 1998. One future application of GMR that is contemplated by
researchers is non-volatile magnetic random access memory (MRAM). What
is interesting about this MRAM is that, not only has the material size
requirement per bit been dramatically reduced, but also the memory access
time has dropped from typically a few milliseconds to nanoseconds. In
addition, due to GMR effect inherent resistance to radiation damage, these
memories are expected to be used for space and defence applications. Thus the
GMR effect indeed could be exploited for many exciting applications thanks
to its properties. However, a challenge to GMR device performance would be
the signal-to-noise ratio. In-plane GMR device performance suffers from low
signal-to-noise ratios as the device lateral dimensions get smaller than 1
micron. Research on vertical GMR devices that give larger signals as the
device dimensions shrink are underway.
 Figure 1. IBM commercial GMR read head.

As an illustration, at 10 nm lateral size, GMR devices could provide signals in

excess of 1 V and memory densities of 10 Gbit on a chip. This is comparable
to that stored on conventional magnetic disks. If successful, the chip would
eliminate the need for magneto-mechanical disk storage with its slow access
time in milliseconds, large size, weight, and power requirements.

3.3c High power magnets:

The magnetic strength of a material is measured in terms of coercivity and
saturation magnetization values. These values increase with decrease in grain
size and increase in the specific surface area of the grains. Magnets made of
nanocrystalline yttrium-samarium-cobalt grains possess very fascinating
magnetic properties due to their extremely large surface area. Some typical
applications include quieter submarines, auto-mobile alternators, land-based
power generators, motors for ships, ultra-sensitive analytical instruments, and
magnetic resonance imaging in medical diagnostics.

4. Processing methods

4.1 Processing of nanocrystalline materials

Plasma processing:
A non-transferred arc thermal plasma reactor has been used to vapor-ize
coarse metal powders. A supersonic nozzle is used to quench the powder, and
the powders are collected in a filter system that can be sealed and dismantled
in a glove box. A drawback of the process is oxidation during fine powder
handling.
i) Combustion process:
The combustion process utilizes oxidizers and fuels. In controlled
environments, high temperatures can be generated by the exothermic redox
reactions between decomposition products of the oxidizer and the fuel.
Owing to the fast heating and cooling, there is nucleation of crystallites but
little growth, resulting in nanocrys-talline ceramics. Some of the process
features are as below.
(a) It is a versatile process leading to the synthesis of single
phase, solid solutions, and composites as well as complex
compound oxide phases.
(b) It uses cheap raw materials.
(c) It is a scalable and high production rate process.
(d) The products are of high purity and loosely agglomerated,
resulting in high sinter-ability.
ii) Mechanical alloying:
A high-energy ball milling process has been used to produce nanos-
tructured powders.
Rapid solidification processing – Amorphous alloys to be produced by a
variety of rapid solidification processing routes with cooling rates > 104 K/s
for eutectic alloys.
Solidification processing of bulk amorphous alloys – Bulk amorphous
alloys are formed by more conventional solidification routes at slower
cooling rates.
Crystallisation of amorphous precursors – Bulk alloys with
nanocrystalline grains can also be produced by solid state (crystallisation)
of an amorphous precursor.

4.2 Rapid solidification techniques

i) Spray Methods:
The melt is fragmented into droplets prior to quenching. Powder is produced
by this method. The mechanism of atomisation and the means of cooling can
be different in different techniques. Some atomisation methods are by gas,
water, ultrasonic, rotating, soluble gas, electrohydrodynamic, spark erosion,
and twin roll means.

(ii)Chill Methods:
The continuity of the melt is preserved up to and during quenching. This is
achieved by bringing the melt into contact with a chilling substrate. Various
methods involve injecting the melt into a die cavity, forming the melt into a
thin section by forging between a hammer or piston and an anvil, extruding the
melt on to a chilled surface or extraction of the melt by contact with a rotating
disc. Some chill methods are by using dies, piston and anvil, twin roller
quenching, free flight melt spinning, chill block melt spinning, planar flow
casting, and melt overflow.

4.3 Sol–gel synthesis as a processing method

Sol–gel synthesis is widely used due to some advantages such as those listed
below.
i) Produces materials (both metals and ceramics) at low temperatures
ii) Able to produce in large quantities (commercially viable) relatively
cheaply .
iii) Can synthesize many materials.
(iv) Co-synthesize two or more materials simultaneously.
(v) Produce extremely homogeneous alloys and composites.
The sol–gel process is able to control the microstructure of the final products
accurately and thus control the physical, mechanical, and chemical properties
of the final products.

5. Powder injection moulding of nanostructured magnetic materials

By the use of the powder injection moulding technique with nanostructured

magnetic mate-rials, the following advantages can be obtained:
(a) High shape complexity: PIM can produce more complex parts
than either investment casting or traditional press and sinter
techniques.
(b) High density: PIM parts produced with our feedstock will have
density levels between 97.5 and 99.5%. These levels typically
exceed traditional press and sinter techniques, and are
comparable to investment casting.
(c) High performance: Nanocrystalline magnetic materials are
exceptionally strong, hard, and ductile at high temperatures.
They have lowest energy losses (narrowest B=N hysteresis
loop), high permeabilities and exhibit nearly or exactly zero
magnetostriction.
(d) Low cost: Cost savings can be realized by eliminating
machining operations, secondary coining operations or surface
impregnation.
 6. Potential applications of PIM to nanostructured materials

6.1 High-sensitivity sensors

Sensors employ their sensitivity to the changes in various parameters they are
designed to measure. The measured parameters include electrical resistivity,
chemical activity, magnetic permeability, thermal conductivity, and
capacitance. All of these parameters depend greatly on the microstructure
(grain size) of the materials employed in the sensors. A change in the sensor's
environment is manifested by the sensor material's chemical, physical, or
mechanical characteristics, which is exploited for detection. For instance, a
carbon monoxide sensor made of zirconium oxide (zirconia) uses its chemical
stability to detect the presence of carbon monoxide. In the event of carbon
monoxide's presence, the oxygen atoms in zirconium oxide react with the
carbon in carbon monoxide to partially reduce zirconium oxide. This reaction
triggers a change in the sensor's characteristics, such as conductivity (or
resistivity) and capacitance. The rate and the extent of this reaction are greatly
increased by a decrease in the grain size. Hence, sensors made by
nanocrystalline materials are extremely sensitive to the change in their
environment. Typical applications for sensors made out of nanocrystalline
materials are smoke detectors, ice detectors on aircraft wings, automobile
engine performance sensor etc.

6.2 Solenoid assembly

The strength of a magnet is measured in terms of coercivity and saturation
magnetization values. These values increase with a decrease in the grain size
and an increase in the specific surface area (surface area per unit volume of
the grains). The key properties of the solenoid assembly, made of iron-nickel
steel by PIM, are magnetic permeability and magnetic strength. With
nanostructured iron-nickel steel, high magnetic permeability and magnetic
strength are achieved and value-added products to both producers and
consumers are, possible.
A solenoid with a metal housing and a moving piston, which is held in
position by a spring. As the solenoid is energized, a magnetic flux is generated
in the surrounding materials. Since the lines of force run across the air gap, the
movable piston is pulled axially, overcoming the spring force. When de-
energized, the system loses its magnetic field and the spring pushes the piston
back into the original starting position. Such a device can be used to perform a
number of short-stroke functions. This includes opening and closing valves
and switches.
9. Summary

Specific examples of the use of nanostructured electronic and magnetic

materials have been cited and potential applications of PIM of nanomagnetic
material are discussed. Processing techniques which are scalable to industrial
practice are cited and comparative advantages have been outlined. The case of
powder injection moulding of both conventional and nano-magnetic materials
is discussed and it appears that the most significant areas of application for
this technology are high-sensitivity sensors and solenoid assemblies. However,
controlling the particle preparation process, process control, process and
product relationship that leads to continuous uniformity are the opportunities
as will as the challenges in the technology.

References

Cahn R W (ed.) 1991 Materials science and technology; A comprehensive

treatment. Vol 15: Pro-cessing of metals and alloys (Weinheim: VCH)
DeCristofaro N 1998 Amorphous metals in electric power distribution
applications. MRS Bull. 23: 50–56
Edelstein A S, Cammarata R C (eds) 1998 Nanomaterials: Synthesis,
properties and applications
(London: Inst. Phys.)
Inoue A 2001 Bulk amorphous and nanocrystalline alloys with high functional
properties. Mater. Sci. Eng. A304–306: 1–10
Kneller E F 1991 The exchange spring magnet: A new material
principle for permanent magnets.
IEEE Trans. Magnet. 27: 3588–3600
Lall C 1992 Soft magnetism: Fundamentals for powder metallurgy and metal
injection moulding. (Princeton, N J : Metal Powder Industries Federation)
pp 90–92
McHenry M E, Willard M A, Iwanabe H, Sutton R A, Turgut Z, Hsiao A,
Laughlin D E 1999a Nanocrystalline materials for high temperature soft
magnetic applications. Bull. Mater. Sci. 22: 495–501
McHenry M E, Willard M A, Laughlin D E 1999b Amorphous and
nanocrystalline materials for applications as soft magnets. Prog. Mater. Sci.
44: 291–433
Wu Y Q, Ping D H, Murty B S, Kanekiyo H, Hirosawa S, Hono K 2001
Influence of heating rate on the microstructure and magnetic properties of
Fe3B/Nd2Fe14B nanocomposite magnets. Scr. Mater. 45: 355–362
Yoshizawa Y, Oguma S, Yamauchi K J 1988 New iron based soft magnetic
 alloys composed of ultrafine grain structure. J. Appl. Phys. 64: 6044
Yoshizawa Y 2001 Magnetic properties and applications of nanostructured
soft magnetic materials. Scr. Mater. 44: 1321–1325
Document By
SANTOSH BHARADWAJ REDDY
Email: [email protected]
1.Engineeringpapers.blogspot.com
2.www.matlabcodes.com
3.microcontroller-project-codes.blogspot.com
4.microcontroller-library.blogspot.com
5.arduino-projects-here.blogspot.com
6.labview-projects.blogspot.com
7.java-basics.blogspot.com
8.itsnanoworld.blogspot.com
More Papers,Projects and Presentations available on above
sites.