Scribd
Upload
59 views4 pages

200 MK2 Data

The D-200 MK2 is a low-cost modular generator controller that can be monitored over the internet through plug-in modules. It supports diesel and gas generators, has features like idle speed control and battery charging, and measurements including voltage, frequency, and engine speed. Communication options include USB, Ethernet, GPRS, and SMS, allowing for remote control and central monitoring.

Uploaded by

ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
59 views4 pages

200 MK2 Data

The D-200 MK2 is a low-cost modular generator controller that can be monitored over the internet through plug-in modules. It supports diesel and gas generators, has features like idle speed control and battery charging, and measurements including voltage, frequency, and engine speed. Communication options include USB, Ethernet, GPRS, and SMS, allowing for remote control and central monitoring.

Uploaded by

ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

THE NEW D-200 MK2

The D-200 MK2 is the lowest cost


modular genset controller ready
for internet monitoring through
plug-in modules.

FEATURES PLUG-IN MODULES


• Diesel and gas genset support • Battery back-up real time clock • GSM Modem (2G-3G-4G)
• 400Hz operation support • Idle speed control • Ethernet 100Mbits
• 400 event logs, full snapshot • Battery charge run enabled • Wi-Fi (802.11 b/g/n)
• All parameters front panel • Combat mode support • RS-485 (2400-57600baud)
editable • Multiple nominal conditions • RS-232 (2400-57600baud)
• 3 level configuration password • Contactor & MCB drive
• 128x64 graphical LCD display • 4 quadrant genset power FUNCTIONALITIES
• Downloadable languages counters
• Waveform display of V & I • Mains power counters • AMF unit
• Harmonic analysis of V & I • Fuel filling counter • ATS unit
• 16Amp MCB & GCB outputs • Fuel consumption counter • Remote start controller
• 6 configurable digital inputs • Modem diagnostics display • Manual start controller
• 5 configurable digital outputs • Configurable through USB, • Engine controller
• 3 configurable analog inputs RS-485, Ethernet and GPRS
• CANBUS-J1939 or MPU input • Free configuration program TOPOLOGIES
• 3 configurable service alarms • Allows SMS controls
• Multiple automatic exerciser • Ready for central monitoring • 3 ph 4 w, star & delta
• Weekly operation schedule • Mobile genset support • 3 ph 3 w, 2 CTs
• Dual mutual standby with • Automatic GSM geo-location • 2 ph 3 w
equal aging of gensets • Easy USB firmware upgrade • 1 phase 2 wires
• Manual “speed fine adjust” on • IP65 rating with optional gasket
selected ECUs
COMMUNICATION
• Automatic fuel pump control MEASUREMENTS • USB Device
• Disable protections feature • J1939-CANBUS (optional)
• Mains & genset PN/PP voltages
• Excess power protection • Geo-locating through GSM
• Mains & genset frequency
• Reverse power protection • Internet Central Monitoring
• Mains & genset phase currents
• Overload IDMT protection • SMS message sending
• Mains & genset neutral currents
• Load shedding, dummy load • E-mail sending
• Mains & genset, phase & total,
• Multiple load management • Free PC software: Rainbow Plus
kW, kVA, kVAr, pf
• Current unbalance protection • Modbus RTU (2400-57600baud)
• Engine speed
• Voltage unbalance protection • Modbus TCP/IP
• Battery voltage
• Fuel filling & fuel theft alarm
PLUG-IN MODULES

Backpanel view Plug-in modules

SCOPEMETER & HARMONICS RAINBOW PLUS PROGRAM


HARMONICS

USB

RAINBOW SCADA CENTRAL MONITORING

Fleet Display on Map, online monitoring Smartphone Support


COMMUNICATIONS

USB

ho

TECHNICAL SPECIFICATIONS
Alternator voltage: 0 to 300 V-AC (Ph-N) Maximum humidity: 95% non-condensing.
Alternator frequency: 0-600 Hz. IP Protection: IP65 from front panel, IP30 from the rear
Mains voltage: 0 to 300 V-AC (Ph-N) (with gasket)
Mains frequency: 0-600 Hz. Dimensions: 133 x 107 x 46mm (WxHxD)
Topology: 1-2-3 phases, with or without neutral Panel Cut-out Dimensions: 117 x 87 mm minimum.
DC Supply Range: 8.0 to 36.0 V-DC. Weight: 250 g (approx.)
V-A-cos Accuracy: 0.5% + 1 digit Case Material: High Temperature, non-flammable
kW-kVA-kVAr Accuracy: 1.0% + 1 digit ABS/PC
Current consumption: 180 mA-DC max @ 12V-DC Installation: Flat surface mounting on a Type 1 enclosure.
Current Inputs: current transformers. ../5A or ../1A. Rear retaining plastic brackets.
Digital inputs: input voltage 0 to 36 V-DC.
Analog input range: 0-5000 ohms.
Mains and genset contactor outputs: 16Amps@250V CONFORMITY
DC Outputs: Protected mosfet semiconductor outputs,
rated 1Amp@28V-DC EU Directives Conformity
Cranking dropouts: survives 0V for 100ms. -2014/35/EC (low voltage)
Magnetic pickup voltage: 0.5 to 50VAC. -2014/30/EC (electro-magnetic compatibility)
Magnetic pickup frequency: 0 to 10000 Hz. Norms of reference:
Charge Alternator Excitation: 2W. EN 61010 (safety requirements)
Display Screen: 2.9”, 128x64 pixels EN 61326 (EMC requirements)
USB Device: USB 2.0 Full speed UL & CSA Compatibility:
Operating temperature: -20°C to 70°C (-4 to +158 °F) -UL 6200, Controls for Stationary Engine Driven
With optional display heater: -40°C to 70°C Assemblies (Certificate # - 20140725-E314374)
Storage temperature: -40°C to 80°C (-40 to +176°F) -CAN/CSA C22.2 No. 14-13 – Industrial Control
Equipment
TYPICAL CONNECTIONS

You might also like