®

BoxBolt
Hollow Profile
Fastener
Galvanized steel,
blue passivated (A2K)
Hot-galvanized steel
Stainless steel A4 prurostof
The mechanical material properties of the
screws are strength class 8.8 according
to DIN EN ISO 898-1:1999-11 or strength
class 70 according to DIN EN ISO
3506-1:1998-03.
Nom. Screw Size of Size of Sleeve Collar Sleeve Clamp. length lk Galvanized steel, Hot-galvanized steel A4 ru
prost
of
dia. length dia. thickness length blue pass. (A2K)
screw sleeve Min. Max.
l mm S in mm SSl in mm dSl in mm kSl in mm lSl in mm in mm in mm Art. No. P. Qty. Art. No. P. Qty. Art. No. P. Qty.
M 61 45 10 18 10.5 5 35 3 29 0485 806 1 100/1
50 40 3 26 0485 808 1 0485 908 1 0487 908 1 50/1
50/1 50/1
M8 70 13 22 13.5 6 60 12 46 0485 808 2 0485 908 2
90 80 24 66 0485 808 3 40/1 0485 908 3 40/1
50 40 3 23 0485 810 1 0485 910 1 0487 910 1 20/1
M10 70 16 24 17.5 7 60 15 43 0485 810 2 25/1 0485 910 2 25/1
90 80 30 63 0485 810 3 0485 910 3
55 45 3 25 0485 812 1 25/1 0485 912 1 25/1 0487 912 1 20/1
M12 80 18 26 19.5 8 70 18 50 0485 812 2 0485 912 2
20/1 20/1
100 90 36 70 0485 812 3 0485 912 3
75 61 3 35 0485 816 1 0485 916 1 0487 916 1 10/1
M16 100 24 36 25.5 9 85 24 60 0485 816 2 10/1 0485 916 2 10/1
120 105 48 80 0485 816 3 0485 916 3
100 78 3 42 0485 820 1 0485 920 1 0487 920 1 5/1
M 20 120 30 46 32.5 11 108 30 72 0485 820 2 5/1 0485 920 2 5/1
150 133 60 102 0485 820 3 0485 920 3
1 Without construction permit

For fastening to hollow profiles or to Tip: We recommend the BoxSokTM special

With general other hard-to-reach components. The tool for installation.
construction permit fastener is especially suitable for appli-
Z-14.4-482 For application examples, see reverse.
cations in which the installation point is
only accessible from one side. Safety precaution:
The connection is produced by tightening Never exceed the permissible working
the screw while bracing the sleeve collar loads. Before using the hollow profile
and the resulting spreading of the sleeve. fasteners, it must be checked whether the
The tightening torques must be applied steel structure can withstand the required
using a torque spanner. loads.
The hollow profile fastener is only
approved for one-time use!

Nom. dia. Drilling dia. Tightening Edge and hole spacing Maximum working load in kN 1
(tolerance torque mandatory for design Galvanized and hot-galv. steel Stainless steel A4
+1/–0.25) Minimum spacing in mm Perm. tensile Perm. shear load Perm. tensile Perm. shear load
in mm in Nm A B load N perm.1 Vperm.1 load N perm.1 Vperm.1
M6 2 11 19 30 11 5.712 16.212 – –
M8 14 25 35 13 12.86 21.07 13.29 26.14
M10 18 45 40 15 24.07 37.0 21.07 47.07
M12 20 80 50 18 29.43 48.29 30.64 59.86
MWF - 08/11 - 10702 - © •

M16 26 190 55 20 52.29 88.21 57.07 108.57

M 20 33 300 70 25 92.0 145.36 89.07 181.79
1 Nperm. = N R.d / γF or Vperm. = Va.R.d / γF (part-safety coefficient γF = 1.4). With the simultaneous
occurrence of pulling and shearing off, DIN 18800-1:1990-11, element (810) must be observed.
2 Nominal dia. M6 without construction permit BoxBolt® is a registered trademark of Access Technologies Limited, GB.

01 0707