Line Driver / Volume Control

Owner’s Enjoyment Manual

Congratulations!
You have just purchased a high-performance autosound product, the
AudioControl OVERDRIVE PLUS Line Driver. The OVERDRIVE PLUS
will allow you to utilize every last bit of performance and sound quality
that you’ve always strived for from your vehicle’s sound system. In addi-
tion, your new OVERDRIVE PLUS provides you with an input to accept
an optional dash mounted remote level control. The OVERDRIVE PLUS
can now be both a line driver and a remote volume/bass control. Find a
nice dry spot well away from the rainforest drizzle, and take in the clean
air along with this Enjoyment Manual for the OVERDRIVE PLUS Line
Driver.
Key Features of the OVERDRIVE PLUS:
• High signal voltage capability: 9.5 volts RMS output
• 24 dB of gain
• Input for optional Dash Control for remote level
• Ultra-low distortion, ultra-quiet operation
• Low noise, high current output circuitry
• High-headroom PWM switching power supply
• Selectable ground isolation
• Voltage indicator LEDs

®
making good sound better®
Features
High-Voltage Line Driver
The OVERDRIVE PLUS is a line driver that takes the input voltage
of a high performance source unit and increases it (up to 13 volts peak).
It then delivers this punched up signal to the amplifier for more lifelike
sound with less noise, less distortion and more dynamic range. In short: it
makes music played on your system sound more like live music.

Input for Optional Dash Control

An optional dash control (sold separately) can be plugged into the
OVERDRIVE PLUS to allow you to adjust the output gain remotely. You
can use this to have a remote system volume control or to have a remote
amp volume control.
Low Noise / High Current Output Circuitry
Driving long lengths of cable can present a nasty capacitive load to the
source that has to drive them. The OVERDRIVE PLUS’s low-impedance,
high-current output circuitry can easily handle long cable runs without
their associated problems.
Output Voltage Indicators
Setting voltage levels for best signal-to-noise performance can be a real
pain — especially when you have to get out the old digital voltmeter and
find a way to make those probes stay put while you try to read the dancing
LCD display. With the OVERDRIVE PLUS’s voltage indicator LEDs,
we remove some of the pain. The first LED indicates that you are in the
OVERDRIVE PLUS’s comfortable working range. The second LED lets
you know you are over 8 Volts and better make sure your amp can take
that much input.
--
 Remember: At full gain, this unit has enough output to “overdrive”,
no pun intended, many amps. The LEDs read voltage not sound and are
only used to warn you of potential clipping issues. If you get plenty of
volume without lighting the LED’s … Don’t Worry! It just means you’re
not clipping and you have lots of Headroom in the signal.
Selectable Ground Isolation
Avoiding ground loops and grounding-related noises are of paramount
importance in any installation. For this reason we have provided a flexible
scheme of isolating grounds.
AudioControl’s Bulletproof Reliability
That’s right, your AudioControl OVERDRIVE PLUS comes with a
full 5 year parts and labor warranty when it is installed by an authorized
United States AudioControl dealer. These seasoned pros have the training
and the equipment to take care of the job quickly. Keep in mind that if
you or your friends are “good with electronics” and you choose to install
it yourselves, your OVERDRIVE PLUS still has a 1 year parts and labor
warranty. To activate your warranty, simply go on-line to www.audiocon-
trol.com. Click “Mobile Audio” then “Warranty Registration” and fill in
the blanks. Or, you can go directly to http://audiocontrolregistration.com
to register.
Also, save your invoice or sales slip as proof of purchase. Not only
are these necessary for warranty purposes, they are also important if the
unforeseen disappearance of your OVERDRIVE PLUS should happen
while you are socializing at the local espresso and salmon bar. Insurance
companies have very little imagination.
AudioControl Sound Quality
Yes, when all is said and done, this is the most important feature we
offer. Amazing AudioControl Sound Quality. Our mantra is right there
with our logo: making good sound better. We believe every car system
should sound just like a live concert and your new OVERDRIVE PLUS
has been built to do just that.

--
A Guided Tour of the OVERDRIVE PLUS
The Outside
1) Inputs: The AudioControl OVERDRIVE PLUS inputs get their
signals directly from the main source unit/head unit. AudioControl’s high
impedance input design means you get less noise and fewer ground loops.
2) Input Gain Control: Used to increase the amount of signal to your
downstream signal processors or amplifiers. With this control you can
get up to 24dB of gain or 13 volts peak (9.5 volts RMS) to your signal
processor or amplifier inputs. If your head unit’s maximum output is only
500mV, the OVERDRIVE PLUS will be able to squirt out 8 volts RMS
into the rest of your system. Even if your head unit’s output is as little as
250mV, you can still get 4 volts RMS out of the OVERDRIVE PLUS
Line Driver. However, be careful about over driving your average non-
AudioControl crossover or amplifier. Many can’t handle more than about 2
volts input without clipping (AudioControl units can take the full output of
the OVERDRIVE PLUS). If in doubt, check with the manufacturer.
3) Outputs: Next to the inputs are the outputs, which should be con-
nected to the next component in your system. This could be an equalizer,
crossover, amplifier, or virtually any other electronic gadget you may have
in your system. If you connect the outputs to any AudioControl compo-
nent, you can rest assured it can handle the hot signal voltage from the
OVERDRIVE PLUS.
Output status LEDs
4) Power: If you see this one lighted, pat yourself on the back for
properly connecting the power terminal.
5) Signal LEDs 8 volts: When this light flickers while music is play-
ing, you’re pushing the limit — nearing the redline — entering the danger
zone. You still have headroom in the OVERDRIVE PLUS but you need to
make sure your amp can handle the input voltage without clipping. Check
your amplifier specs. Try backing off on the Gain Control until it stops
flickering.

--
 ④
②
⑤

① ③ ⑥ ⑦

1 Volt: This light will tell you when the signal level is at 1 volt. Most
head units will give you enough juice to light this one. You’ll most likely
want at least the 1 volt light to flicker, more if the rest of your compo-
nents can handle it. Any AudioControl component that you connect after
the OVERDRIVE PLUS won’t mind the 8 volt RMS light flickering. Go
ahead. Light it up!
6) Remote Level Control (sold separately): The port allows you to
plug an optional dash mounted remote level control. Now you can have a
separate system volume control or if the OVERDRIVE PLUS is driving
just your bass amp, you can have a separate bass control for the system.
--
 7) Power Connector: This convenient little connector allows you to
hook up all the power and turn-on wires for your OVERDRIVE PLUS
Line Driver in the convenience of a well-lighted area and then plug them
in by feel all at once in your trunk’s cavernous darkness. Screws on top
of the connector should face up. But if you put the plug in upside down,
nothing will be damaged, the OVERDRIVE Plus just will not power up!
The Inside
8) Ground Isolation Jumpers: OK, we all know there are installation
rules to follow for best results. Power and signal wires should be on oppo-
site sides of the car. All units should be tied to a single ground… Yes that
includes the head unit, you know the factory ground sucks…it’s tied to the
headlight dimmer. But, even when we follow all the rules, bad things do
happen on occasion. Should alternator whine rear its ugly head during the
installation, we have provided some alternate power supply

--
grounding choices. Experiment with different settings if you run into this
problem. To change the settings, turn system power OFF, move the black
jumper from the center two pins (fully isolated) to either the top two pins
(ground) or the bottom two pins (200W).

Short course in Signal-to-Noise Ratio and

Level Matching
Signal-to-noise ratio is the difference between the signal level and the
noise floor of an electronic component. The higher the signal, the better.
Since you really can’t reduce the noise floor, signal-to-noise ratio can
be readily improved by raising the signal level. It’s best to get the signal
level up at the beginning of the signal path. The signal-to-noise ratio will
only be as good as the noisiest component. Which is why it’s important to
have a quiet head unit. This “weakest link” theory is the basic idea behind
setting levels in your car’s system. And that’s why AudioControl provides
gain in its signal processors.
Level Matching is about making sure you run just the right amount of
signal into an electronic component. If you send too much, you’ll experi-
ence the not-so-joyous sound of clipping. At the same time, you want
the highest possible signal levels for best signal-to-noise ratio. Since all
AudioControl products are capable of high-voltage input and output, it is
important that you MATCH the input voltage of your components. Most
crossovers and amplifiers can handle up to about 2 volts before they clip.
AudioControl signal processors can all put out at least 7.5 volts RMS, and
can take in 9 volts RMS. LED voltage indicators on many of our products
make it a snap to set levels! Want to learn more about level setting? Check
out the video in the support section of the Mobile Audio pages at www.
audiocontrol.com Also available there, is Tech Note 1006 for those more
technically minded.

--
Installation Examples
and Hookup Diagrams
Basic 2 channel system with
maximum dynamic range

--
2 Channel equalized system with
active crossover / equalizer

Maximum bass system with The

Epicenter Plus and active crossover

--
Dash Control (Purchased Separately)
Placement And Mounting
The dash control may be mounted under the dash using its own
bracket or through a custom hole in the dash. It should be
within reach of the driver and in a spot where the
LED is plainly visible.
Bracket Installation
The dash control mounts
with two screws, which
attach to the underside
of the dashboard.
Slide under the
dash and place
the dash control
in its mounting
position, mark
the two mount- Dash Control Assembly
ing holes, drill pilot
holes, and secure with two screws.
Custom Installation
For that custom, finished look, the dash control can be flush mounted
directly on the dash-board (or anywhere else). Referencing the figure
above, disassemble the dash control from the mounting bracket. Start by
pushing the LED from its holder followed by removing the circuit board
and rotary control from the bracket. Drill a 9/32 hole in the dashboard for
the control along with a 1/8 hole for the lock tab and a 13/64 hole for the
LED holder. Reassemble the dash control components on the dashboard.

- 10 -
Installation Precautions/Hints
Do not mount the OVERDRIVE PLUS Line Driver where it will be ex-
posed to outside elements or extreme temperatures. Avoid areas of severe
vibration or shock, and never drill into a car panel without knowing what’s
behind the panel. Think safety at all times.
• Mounting the OVERDRIVE PLUS as close to the head unit as pos-
sible sends the maximum signal down the wire so you hear more music
and less noise.
• Use high quality, 100% shielded audio cables.
• Plan on a single-point ground scheme so all components, including
the head unit, connect to a common ground point. Clean off all paint to
bare metal at the ground point and use a star washer. Use no less than 14
gauge wire for the power and ground connections.

Set-up
Review the Level Matching section on page 7 of this manual. Level
matching is what will allow you to get all the performance your OVER-
DRIVE PLUS is capable of.
• Turn down your amp gains to their minimum setting, as well as the
gains of any other components coming after the OVERDRIVE PLUS.
Then you can run a higher signal (better signal to noise) into the amplifi-
ers. Don’t worry, your amps will still go to full output with the signal they
get from the OVERDRIVE PLUS.
• Adjust the OVERDRIVE PLUS for the maximum output that the next
component in the chain can handle. The Tech Videos and Tech Notes in
the support section of www.audiocontrol.com will take you through the
level matching procedure. Note: Make certain that whatever component
you put after the OVERDRIVE PLUS can withstand the output voltage
you dial up. The inputs of many crossovers and amplifiers will clip around
2 volts. All AudioControl products can handle inputs of 9 volt RMS.

- 11 -
Blatant Plug
The OVERDRIVE PLUS Line Driver is part of the AudioControl
Performance Match Series of products. The Performance Match products
will extract killer performance from your car stereo system.
There are real world barriers to good autosound such as the fact that
doors and trunks rarely make good speaker boxes. AudioControl Perfor-
mance Match products like the Concert Series 2XS™ and 6XS™ cross-
overs; the Concert Series analog and digital equalizers; and The Epicenter
bass maximizer will help you overcome those barriers. AudioControl
components make it easy to adjust or “voice” components to the specific
acoustics and hostile elements of your stereo system whether it’s a sleek
Honda or stylish Escalade. The result is, as one warranty card stated, “A
dream come true.”

- 12 -
 And now a word from the legal department...

The WARRANTY
People are scared of warranties. Lots of fine print, lots of noncoopera-
tion, months of waiting around. Well, don’t be scared of this warranty.
It’s designed to make you rave about us to your friends. It’s a warranty
that looks out for you and helps you resist the temptation to have your
friend “who’s good with electronics” try to repair your AudioControl
OVERDRIVE PLUS. So go ahead and read this warranty, then enjoy your
new component for a few days before sending in the warranty card and
comments.
“Conditional” doesn’t mean anything ominous. The Federal Trade
Commission tells all manufacturers to use the term to indicate that certain
conditions have to be met before they’ll honor the warranty. If you honor
these conditions, we will warrant all materials and workmanship on your
OVERDRIVE PLUS for five years from the date you bought it, if installed
by an authorized AudioControl dealer, and will fix or replace it, at our op-
tion, during that time.
Here are the conditions that make this warranty conditional:
1. We need to know that you bought your product from an authorized
AudioControl dealer. So go to www.audiocontrol.com or audiocontrolreg-
istration.com right away, and register your OVERDRIVE PLUS.
2. You must keep your sales receipt for proof of purchase, showing
when and from whom the unit was bought. We’re not the only ones who
require this, so it’s a good habit to get into with any major purchase.
3. Your OVERDRIVE PLUS must have originally been purchased from
an authorized AudioControl dealer. You do not have to be the original
owner, but you do need a copy of the original sales slip.

- 13 -
 4. You cannot let anybody who isn’t (A) the AudioControl factory;
(B) somebody authorized in writing by AudioControl to service your
OVERDRIVE PLUS . If anyone other than (A) or (B) messes with your
OVERDRIVE PLUS , that voids your warranty.
5. The warranty is also void if the serial number is altered or removed,
or if the OVERDRIVE PLUS has been used improperly. Now these sound
like big loopholes, but here is all we mean by it.
Unwarranted abuse is (A) physical damage (don’t use the OVER-
DRIVE PLUS for a jack stand); (B) improper connections (120 volts into
the power jack can fry the poor thing); (C) sadistic things. This is the best
mobile product we know how to build, but if you mount it to the front
bumper of your car, something will go wrong.
6. If an authorized United States AudioControl dealer installs your
OVERDRIVE PLUS, the warranty is five years, otherwise the warranty is
one year.
Assuming you conform to 1 through 6, and it really isn’t all that hard to
do, we get the option of fixing your old unit or replacing it with a new one.
Validate your warranty: Visit http://audiocontrolregistration.com to
register your OVERDRIVE PLUS
Legalese Section
This is the only warranty given by AudioControl. This warranty gives
you specific legal rights, which vary from state to state.
Promises of how well your OVERDRIVE PLUS will work are not im-
plied by this warranty. Other than what we’ve covered in this warranty, we
have no obligation, express or implied. Also, we will not be obligated for
direct or indirect consequential damage to your system caused by hooking
up the AudioControl OVERDRIVE PLUS.
Failure to send in a properly completed warranty card, negates any
service claims.

- 14 -
 Specifications
All specifications are measured at 14.4 VDC (standard automotive volt-
age) As technology advances, AudioControl reserves the right to continu-
ously change our specifications, like our weather.
Maximum input/output level ......................................... 9.5Vrms/13V peak
Optional Dash Remote............................................................. +0dB / -90dB
Frequency response....................................................... 10Hz-100kHz;±1dB
Total harmonic distortion.................................................................. 0.005%
Signal to Noise ratio.......................................................................... >110dB
Input Impedance............................................................................ 20 Kohms
Output Impedance............................................................................ 45ohms
Input gain........................................................................................... 0-24dB
Power supply........................ transformer isolated PWM DC/DC converter
Power draw....................................................................................... 150mA
Recommended fuse rating................................................................... 1 Amp
Size...............................................................................5.00” x 4.25” x 1.25”
Weight.................................................................................................... 2 lbs
Input Ground Isolation Jumpers.............................................................. Yes
Country of origin.................................................................................... USA

©2010, AudioControl, a division of Electronic Engineering and Manufacturing, Inc. All

rights reserved.
AudioControl, Making Good Sound Better, Performance Match, The Epicenter, and OVER-
DRIVE PLUS are all trademarks of Electronic Engineering and Manufacturing, Inc.
This literature was conceived, designed, and written under the protective canopy of the lush,
green, misty rain forest on a drizzly, gray overcast day at our home in the Pacific Northwest.

- 15 -
 ®
22410 70th Avenue West • Mountlake Terrace, WA 98043 USA
425-775-8461 • Fax 425-778-3166 • www.audiocontrol.com

P/N 913-104-0

- 16 -