ATR451715
ATR451715
5i-M/M/M
Model: ATR451715
Electrical Properties
790 - 960 2 x (1710 - 2180)
Frequency range (MHz)
790 - 862 824 - 894 880 - 960 1710 - 1880 1850 - 1990 1920 - 2180
Polarization +45° , -45°
0 - 10 , continuously adjustable
Electrical downtilt (°) 0 - 14 , continuously adjustable
each band separately
at mid Tilt 14.5 15.0 15.0 17.1 17.3 17.4
Gain (dBi)
over all Tilts 14.5 ±0.5 14.8 ±0.4 15.1 ±0.5 16.9 ±0.4 17.2 ±0.4 17.2 ±0.4
Side lobe suppression for first side
> 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)
Horizontal 3dB beam width (°) 66 ±3.0 64 ±3.0 62 ±3.0 66 ±4.0 64 ±4.0 63±4.0
Vertical 3dB beam width (°) 15.2 ±0.8 14.8 ±0.8 13.7 ±0.8 7.2 ±0.5 7.0 ±0.3 6.6 ±0.4
VSWR < 1.5
Cross polar isolation (dB) ≥ 30
≥ 30 (790 - 960 // 1710 - 2180 MHz)
Interband isolation (dB)
≥ 30 (1710 - 2180 // 1710 - 2180 MHz)
Front to back ratio, ±30° (dB) > 24 > 24 > 25 > 26 > 26 > 26
Cross polar ratio (dB) 0° > 20 > 20 > 20 > 18 > 18 > 18
Max. power per input (W) 500 (at 50℃ ambient temperature) 300 (at 50℃ ambient temperature)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1497 x 349 x 166
Packing dimensions (H x W x D) (mm) 1825 x 410 x 235
Antenna weight (kg) 19.5
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 29.9 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -55 .. +65
Frontal: 505 (at 150 km/h)
Wind load (N) Lateral: 165 (at 150 km/h)
Rear side: 540 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 6 x 7/16 DIN Female
Connector position Bottom
Accessories
Item Model Description Weight Units per antenna
1
DXXX-790-960/1710-2180/1710-2180-65/65/65-15i/17.5i/17.5i-M/M/M
Model: ATR451715
106
57 57 60
63
1395
1497
Unit: mm
790 - 960
1710 - 2180 X 1710 - 2180
Left Right
X X
+45° -45°
7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F) 7/16 (F)
NOTE
1. Facilities, such as towers and poles, must bear the weight and wind load of antennas.
2. HUAWEI ‘s standard brackets and accessories must be used for any installation.
3. The antenna working environment must meet the requirements specified in the datasheet.
4. Only qualified personnel are allowed to perform installation. Installation tools and procedures must conform to
requirements described in the antenna installation guide.
Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen 518129, P.R.China www.huawei.com/antenna
Any previous datasheet issues become invalid. 2 Issue: 2015-12-30