ProgrammerSought ☰

STMicroelectronics
DOWNLOAD
BLDC Motor Control Solutions

search

Ansys (Ansoft) Maxwell RMxprt Motor Simulation Getting Started Tutorial

tags: ANSYS  Finite element  simulation

Recent topics require ANSYS to perform some simulations on three-phase AC induction motors.

There are many online data on ANSYS analysis, but it feels the most troublesome and di cult for
beginners. I searched the Internet before and I didn't feel that I was a very foolish introductory tutorial.
Later I found a good tutorial on the Internet.Motor modeling，Motor analysis), here is a textual analysis
and summary.

The version of ANSYS used in the tutorial is 18.2. Because of the need for electromagnetic
simulation, an additional version of Ansys Electronics Suite is required. In order to use the Maxwell and

RMxprt modules in the tutorial. Let's take a detailed explanation of the whole step. The whole analysis

process mainly includes two parts: (1) quickly establish a simulation model of three-phase AC motor in
RMxprt (2) analyze the model

(1) Establish a motor model

Step1: Open the ANSYS workbench and drag an RMxprt analysis module from the left side of the

software to the right active window, then double-click Setup to enter the ANSYS electrical analysis

module.
  
Step2: In the project management pane on the left side of the software, right click on RMXprtDesign1

and select the induction motor in the pop-up dialog box.

   

Step3: Then add the solution step button on the stand-alone page, and set the relevant rated
parameters of the motor as shown below.
  
Step4: Double-click the Machine branch in the left item bar. For example, set back some basic
information about the motor.
Step5: Double-click the Stator branch in the left taskbar, and if you set the stator parameters as shown,

then double-click the Slot item in the Stator directory, uncheck Autodesign in the pop-up menu bar,

then double-click the SLot branch again, as shown Set the stator related parameters.
Step6: Double-click Winding under the Stator branch in the left item bar to set the parameters of the

motor stator winding as shown below.

Step7: Next, double-click Rotor to set the rotor parameters, double-click Rotor Slot to design the rotor
slot, double-click Winding to design the rotor winding.
 Step8: Double-click Shaft in the left task bar to set the parameters of the motor shaft.

Step9: After completing the above motor parameter settings, you can select the Validate button on the

page to check the parameters. If there is no problem, you can save it. Then click Analyze All and
Solution Data in the options bar to view some basic parameters of the click constructed. After viewing,
you can close this page and return to the main ANSYS workbench page.
  

(2) Model nite element analysis

Step1: Double-click the Solution button in the RMxprt module in the workbench to enter the click
electromagnetic eld analysis interface.
Step2: Right-click the Setup1 option in the Analysis column on the left side of the project bar and select
“create Maxwell Design”. In the pop-up dialog box, select “Maxwell 2D Design” and click the OK button.
Step3: Select all parts of the mouse frame, select “Set Eddy E ect” in “Assign Excitation” in the menu bar,
and select the “Eddy E ect” option for all the bars.

Step4: Click on Solution Setup on the toolbar and then set up the simulation as shown below. And click
"Add to list", then click "validate" again.
Step5: As shown in the gure, in the “Field Overlay” column on the left taskbar, add the corresponding

analysis domain by the following operations.

Step6: Add the corresponding result analysis object in the left toolbar as shown in the gure.

Step7: After clicking “analyze All”, the system will start calculation. Colleagues can click the
corresponding analysis object in the task bar to view the results of real-time operation.
At this point, this simple example will stop here. Later, according to the progress of the study, the pits of
nite element analysis will be opened one after another. If you have any questions, please leave a
message to communicate.

Discover how STPOWER SiC MOSFETs improve SIGN UP

energy e ciency of industrial applications.

Zabbix disk performance monitoring

Intelligent Recommendation
YDOOK: ANSYS Maxwell 19 Tutorial 22: View of Maxwell 2D Solu
tion Field Diagram
ANSYS Maxwell 19 Maxwell 2D solution eld view After setting the solution steps and
mode, click OK, the solution result and the magnitude of the eld volume need to be
checked by the user, and the f...

STM32 Motor Tutorial 29 - Getting Started 1 no sense brushless

Foreword       Brushless DC （Brushless Direct Current， BLDC) Motor is a positive rapid
spread of the motor type, it can be used in home appliances, automotive, aerospace, cons...

Rmxprt Maxwell 2D and 3D full model generating method

Ansys 19.2 maxwell use a function key to generate a nite element model, often there will
be 2D or 3D simulation is only part of fact, it is cycle model To generate the full model, can
Rmxprt / desig...

YDOOK: ANSYS Maxwell 19 Tutorial 14: How to set the excitatio

n source for Maxwell 2D electrostatic eld What are the excitati
on sources for electrostatic eld
Use ANSYS Maxwell 19 Maxwell 2D to simulate electrostatic eld. How to set the excitation
source and what excitation sources are there for electrostatic eld? 1. Set the solver type 2.
Add voltage e...

An example of a waveform simulation tutorial for getting starte

d with Quartus2
Article directory First, the title description Second, create a project 1. Menu Bar: File->New
Project Wizard 2. Select Device family Third, create a BDF le: arrange components 1.
Introduction to...
 More Recommendation

YDOOK: ANSYS Maxwell Tutorial Electronic Desktop 19 Tutorial

5: Drawing Surface Model
Use ANSYS Maxwell Electronic Desktop 19 to draw surface models Quickly draw surface
models Click the corresponding basic surface graphics in the main function area to draw 1.
Draw a rectangle After dr...

A little experience about installing Ansoft Maxwell 16.0 on a ser

ver or personal PC
The maxwell on the nite element server of the lab has been version 15.0, but the version
of 16.0 installed on my own computer. In the past, the software les of the two softwares
could not be copie...

YDOOK: ANSYS Electronic Desktop Maxwell 19 Tutorial 4: Drawi

ng Equation Curve
Use ANSYS Electronic Desktop Maxwell 19 to draw function equation curves Click the f
function equation curve button in the basic drawing area The Equation Based Curve dialog
box pops up Enter accordin...

Import parameters_parametric modeling tutorial series (5): ANS

YS DesignModeler establishes a parametric geometric model a
nd imports Maxwell...
As the industry continues to upgrade, higher and higher requirements are put forward for
the performance indicators of industrial products in various elds. Design engineers have
slowly found that it...

YDOOK: ANSYS Maxwell 19 Tutorial 13: How to set the excitatio

n source of Maxwell 2D transient magnetic eld What excitatio
n sources are available for transient magnetic eld
How to set the excitation source when using ANSYS Maxwell 19 Maxwell 2D to de ne the
transient magnetic eld What excitation sources are available for the transient magnetic
eld 1. The excitation ...
 STMicroelectronics

By Experienced
Engineers
Sign Up

Related Posts
Call the RMxprt material library in Maxwell
YDOOK: ANSYS Maxwell 19 Tutorial 18: Maxwell 2D On Selection Meshing
ANSYS tutorial-coupling calculation method of Maxwell and Fluent in Workbench
YDOOK: ANSYS Electronic Desktop Maxwell 19 Tutorial 1: Basic Interface
YDOOK: ANSYS Maxwell 19 Tutorial 11: How to set the excitation source for Maxwell 2D electrostatic eld
YDOOK: ANSYS Maxwell 19 Tutorial 7: Maxwell 2D Material Management Add new permanent magnet material
YDOOK: ANSYS Maxwell 19 Tutorial 6: Maxwell 2D Material Management Material Library Add New Material
YDOOK: ANSYS Maxwell 19 Tutorial 21: Maxwell 2D DC Conduction Electric Field Solution Settings Analysis
Settings
YDOOK: ANSYS Maxwell 19 Tutorial 20: Maxwell 2D Surface Approximation Meshing
YDOOK: ANSYS Maxwell 19 Tutorial 17: Maxwell 2D Meshing What are the meshing tools

STMicroelectronics

Live Webcast & New

Products
Subscribe
 Popular Posts
linux miscellaneous notes
Question 1462: [Blue Bridge Cup] [Basic Practice VIP] Hu uman Tree
It seems that I haven't given Amway software to you for a long time. Today I will plant a standard version of
OmniFocus for Mac (GTD time management tool) for you.
Rabbitmq message queue - "routing"
Getting started with mysql stored procedures
mac password-free logon server and submit the password-free git
Academician Zhang Bo: Towards the third generation of arti cial intelligence | Thesis study summary
An article on the design principle of the number of silos at the bottom of the box for many years, I will share it
today. Full of dry goods, remember to collect
Knowledge nishing on March 23
Is the company borrowing the brain? These 4 sentences let you understand!
 STMicroelectronics

By Experienced
Engineers
Sign Up

Recommended Posts
Several problems js will encounter in the interview (below)
linux disk expansion program
Maximum value of the sliding window
Introduction to document ow, Position, and oat
ptrace learning
NYOJ- part and the problem (dfs)
10.3, driver development - kernel module
A summary of mobile security
The second week project three-time complexity
About mysql order by multi- eld sorting problem
 Related Tags
maxwell-permanent magnet synchronous motor
Maxwell 2020 19 Quick Start Collection Detailed Tutorial
ANSYS EDT
On Selection
Maxwell
Technical neighbor
Workbench
ANSYS
education
Engineering

BLDC Motor
Control Solutions
Download ST's
whitepaper and learn
more about our latest
BLDC motor control
solutions.

STMicroelectronics

Download
Copyright © 2018-2021 - All Rights Reserved - www.programmersought.com