INTELLIGENT

FIRE ALARM CONTROL PANELS

MR-2100/MR-2200 Features
Intelligent Addressable Fire Alarm • Listed to UL 864, 9th edition
Control Panels • MR-2100 provides a Single Addressable Input Signaling
Line Circuit (SLC) for up to 198 Addressable Devices
• MR-2200 provides Dual Addressable Input Signaling
Line Circuits for up to 396 Addressable Devices
• SLCs are selectable for either Class A (Style 6) or Class
B (Style 4) operation
• Two Notification Appliance Circuits (NACs), Class A
(Style Z) or Class B (Style Y); expandable to eight NACs
with optional MRNC2 modules
• Four programmable functions relays, Form C; expandable
to sixteen relays with MRRL4 modules
• Programmable cross-zoning functions, day/night mode,
and selective control operations
• Two aux. power outputs, 500 mA @ 24 VDC each
• 6.0 A Power supply with integral battery charger provides
2.5 A for NACs and Auxiliary Outputs; Expandable to
provide up to 7 A NAC Current
• Four additional communications ports for Dialer, PC
Interface, Voice Evacuation System, and Remote
Annunciators
• Optional Style 7 (DCLR) MR network peer-to-peer
MR-2100/MR-2200 Fire Alarm Control Panel communications
(shown with optional LED modules) • LCD/LED system status display with optional MRLD8
LED zone display modules (required for ULC listed
Description applications)
Secutron's MR-2100 and MR-2200 intelligent addressable • Surface/flush mount cabinet with dead front construction
fire alarm control panels provide flexible and cost effective allows up to 12 Ah batteries internally mounted
operation to satisfy system requirements for both economy • Battery charger is capable of charging up to 35 Ah
and capability. Their modular design assures that as system mounted in an external battery cabinet
needs and applicable codes evolve, fire alarm control panel
functions can be updated as required. • Cabinet doors are removable for easy installation
• Terminal blocks are removable for easy wiring
Optional networking modules allows the MR-2100 and
MR-2200 to be connected to a Secutron network to provide • Operating program and database can both be uploaded/
additional input circuits, visual zones, programmable downloaded using a Windows® based PC with Secutron
notification appliance (bell) circuits, and relays. Up to 254 Programming Software
control and annunciator units can be networked together. The • Non-volatile event history log stores 1000+ events
network is a DCLR (Data Communications Link, Redundant)
configuration loop.
The MR-2100 models provide a single addressable input Programming the MR-2100/MR-2200 consists of two
Signaling Line Circuit for support of up to 198 addressable convenient and easy operations. Input circuit programming
devices; up to 99 detectors and up to 99 control/monitor and special features (such as cross zoning functions, day/
modules. night mode, selective control operations, etc.) is performed
from an externally generated database produced on a
The MR-2200 models provide two SLCs for support of Windows® based PC. System parameters and control panel
198 devices on each allowing a total capacity of up to 396 display and operation functions are conveniently programmed
addressable devices; up to 198 detectors and up to 198 from the on board LCD and keypad.
control/monitor modules total.
Option modules are available and can be conveniently field
installed. Modules are available for: additional NAC output
circuits & function relays, local LED annunciation, additional MEA
approved
NAC power, and Central Station (DACT) or Remote Station
(DACT or CITY Module) connection. S6619 S6619 7135-1656:106 352-03-E
7170-1656:117

Issue 2 SECUTRON INC. Page 1 of 6

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 1005 • Not to be used for installation purposes.
Main Control Unit
System controls consist of eight system switches, an LCD Intelligent Addressable Input Circuits
readout, and display entry switches. The display entry Up to 99 intelligent addressable detectors and up to 99
keypad is used for technical functions, system/detector addressable control/monitoring modules may be connected
maintenance, history recall, device and circuit disarming, per SLC for a total of 198 addressable devices. MR-2100
and for manual operation of addressable output modules, models provide a single SLC output, MR-2200 models
relay modules, and notification appliance (bell) circuits. provide dual SLCs.

Addressable monitoring modules can be programmed for

Operator Keys alarm or supervisory functions. Control modules are available
There are eight operator keys. In the figure below, the for dry contact or supervised output functions.
keys are located on the lower left and are labeled “System
Controls.” The LEDs associated with these keys are used to
display function status. The top three keys are pre assigned
and are: Acknowledge, Signal Silence, and System Reset. NAC Outputs
Standard are two NACs rated 2 A maximum. NAC output
The bottom five keys are user-assignable, selected for the voltage is a nominal 24 VDC, full wave rectified. NAC
following functions: Lamp Test, Relay Disconnect, Test expansion can be up to eight NACs by using MRNC2 NAC
Mode, Signal Disconnect, Common Disconnect, General expander modules.
Alarm, Selectable Switch Function On, Switch Function Off,
or Manual Restart.

The panel local sounder will beep once when a valid key is Auxiliary Outputs
pressed and beep three times if an invalid or unavailable key Two auxiliary power outputs are provided, each rated for 500
is pressed. Key presses are recorded in the history log. mA at a nominal 24 VDC, filtered and regulated.

INSTRUCTIONS: Function Relays

The panel comes with four programmable Form C function
relays rated 2 A @ 30 VDC resistive. Total function relays
can be expanded to 16 by using MRRL4 relay expander
modules. Relays can be programmed as Common Alarm,
SYSTEM CONTROLS SYSTEM DISPLAY AND PROGRAMMING
Common Trouble, Common Supervisory, or general purpose
Acknowledge
functions.
ALARM
ALARM SUPERV TROUBLE MONITOR
Signal Silence
SUPERVISORY
System Reset
TROUBLE

AC
1 2 3 ENTER
Power Supply and Expansion Transformer
MONITOR
4 5 6 CLEAR Each MR-2100 / MR-2200 fire alarm control panel is shipped
with a 120 VAC / 240 VAC transformer. Total NAC power
User Assigned
BYPASS

7 8 9
can be increased by adding a second transformer, MR-XPS.
HOME
GROUND FAULT

NAC TROUBLE LAMP

TEST

The standard power supply provides 2.5 A @ 24 VDC (full

wave rectified, unfiltered) for the total of NAC and Auxiliary
MR-2100/2200 Main Control Panel power output. With the addition of an optional transformer,
the total NAC and Auxiliary power output is increased to 8 A
with up to 7 A available for NACs.
Display Information
The Main Control Panel LCD readout is backlighted and
displays 4 lines with 20 characters per line. With AC power Enclosure Details
present, the LCD backlighting turns off automatically within The enclosure includes the mounting box, outer door, dead
5 minutes if no activity occurs. During AC power failure, the front door, and hardware plate. It can be flush or surface
backlighting will turn off within 30 seconds without activity. mounted without requiring a separate trim ring.

During normal conditions the display is the main menu Both the outer door and dead front doors are removable.
which includes the date and a 24 hour clock. During alarm The hardware plate holds the main printed circuit board
conditions, the first or last (selectable) events of highest and transformer(s). This enclosure holds two transformers,
priority will be displayed instead of the main menu. A up to three NAC or Relay expander modules, and one
status summary screen lists the number of active alarm, communicator module.
supervisory, or trouble events indicating “SYSTEM OFF
NORMAL.” The backbox is included with the fire alarm control panel and
includes an outer lip around the perimeter to provide a built in
trim for semi-flush mounting applications. The door conceals
the outer lip and provides a neat and clean appearance for
surface mounted box applications.

Page 2 of 6 SECUTRON INC. Issue 2

Catalog Number 1005
Not to be used for installation purposes.
Optional Features Compatible Products
NAC Expander Board Model MRNC2 LCD Annunciator Model MR-2644
NAC Expander Boards provide two additional NAC outputs. For remote information annunciation, model MR-2644 is an
Up to three modules can be added within the basic enclosure LCD status annunciator with display, general system status
and can be any combination of NAC or Relay expanders. LEDs, and general function keys.
NAC Expander Board NACs are rated for 2 A @ 24 VDC (MR-2644 is not ULC Listed.)
each, the same as the standard NACs.

Relay Expander MRRL4

Relay Expander module MRRL4 provides four additional
function relay outputs. Each relay provides a Form C contact
rated 2 A @ 30 VDC resistive with dry contacts requiring
connection to a power limited source.

Eight Zone LED Module MRLD8

For local LED panel mounted zone annunciation, the MRLD8
module provides eight zones of LED annunciation, readily MR-2644 Remote LCD Annunciator
visible on the front of the control panel cabinet. Up to three
LED modules can be mounted on the front of the cabinet.
Each module has label pockets to locally identify zone
locations.
NOTE: An MRLD8 LED module is required for ULC listed
applications. LED Annunciator Model MR-2614
Model MR-2614 is a status annunciator with LED zone
display, general system status lights, and general function
DACT Module - MRDL keys. It provides up to 72 LED zones with three status LEDs
The optional Digital Alarm Communicator Transmitter (DACT) per zone.
module is added to the system to provide Remote Station
monitoring of system alarms, troubles, and supervisory
conditions. Communications are available for : Contact ID,
SIA, or 10/20 bps formats.
Use of the DACT module requires that two telephone lines
be provided for connection to the DACT. Service must be
arranged with a Central Station monitoring facility for Remote
Station Service.
(MRDL is not ULC listed).

City Connection Module MRCTYB

Optional module MRCTYB can be configured for remote
Station (reverse polarity) or Municipal Master (local energy)
service. The MRCTYB can transmit alarm, trouble, and
supervisory conditions when configured for reverse polarity
operation. Alarm conditions are only reported when configured
MR-2614 Remote LED Annunciator
for Municipal Master operation.
Note: The MR-2100/MR-2200 accepts either the MRDL or
the MRCTYB module.

Peer-to-Peer Networking
MR-2100/2200 control panels can be networked to other
control units for up to a total of 254 network members, each
using Style 7 (DCLR) loop communications. One control unit
is designated as the master control unit for the network and
diagnostics can be done at any control unit.

Programming of each individual control unit is done at that

unit. Each control unit operates independently in a standalone
mode if network communications are lost.

Issue 2 SECUTRON INC. Page 3 of 6

Catalog Number 1005
Not To Be Used For Installation Purposes.
Specifications
Input Power
120 VAC, 60 Hz 2 A maximum Ratings are per transformer; one additional transformer may be added to increase
240 VAC, 50 Hz 1 A maximum capacity

Mechanical
Overall Dimensions with Door 16-7/8” W x 29-1/2” H x 5-1/4” D (429 mm x 749 mm x 133 mm) [see page 5 for mounting box detail]
Environmental
Temperature Range 32° to 120°F (0° to 49° C)
Humidity Range Up to 93% RH, non-condensing @ 90° F (32° C) maximum
Signaling Line Circuit Ratings
Voltage 24 VDC nominal, 27.5 VDC maximum
MR-2100, Single SLC: 198 total, 99 detector, 99 control/monitor modules
Max. number of devices
MR-2200, Dual SLCs: 396 total, 198 detectors, 198 control/monitor modules
Compatible devices Refer to list on page 5
Maximum line length 3045 m (10,000 ft) (12 AWG, 3.31 mm2)
Available as Style 6 (Class A) or Style 4 ( Class B); T-tapping is allowed with Style 4 (Class B) connections
Operation modes
only
Notification Appliance Circuit Output Circuits, Standard and Expansion NACs
NAC Output Ratings 2 A maximum per NAC; 24 V full wave rectified DC output; power limited
NAC Current, Standard with Total of NACs + Auxiliary Power = 2.5 A maximum
One Transformer (if Aux. Power Total = 500 mA; NAC power = 2 A maximum)
Total NAC current = 7 A maximum
NAC Current with Optional
Total of NACs + Auxiliary Power = 8 A maximum
Transformer
(optional transformer MR12VAC or MR24VAC)
Function Relay Output Circuits, Standard and Expansion Relays
All Relays 2 A @ 30 VDC resistive; Form C contacts; requires power limited source
Power Output Circuits
Auxiliary Power Outputs Each output is rated 500 mA @ 24 VDC, filtered, regulated, and power limited; maximum ripple voltage
(two outputs) = 600 mVpp
Battery Information
Battery Charger current limited float charger for sealed lead acid batteries
Float Charge 27.5 VDC
Charging Current 2.7 A maximum, no auxiliary loads; 1.7 A nominal with 0.5 A on each Auxiliary output
12 Ah maximum size internal to cabinet;
Maximum Battery Capacity
35 Ah maximum size allowed, requires model MR2978 External Battery Cabinet
Communications Ports
Fixed baud rate @ 4800 bps; for use with MR-2614 or MR-2644 Annunciators (refer to individual product
ANN (annunciator port)
Installation Instructions for capacities and wiring distances)
Fixed baud rate @ 9600 bps; 20 ft (6m) maximum distance; for use with MV-2700 Voice Evacuation
RS-232-2 (MV-2700 or GRID)
System or GRID Graphical PC Display
CON4 (Dialer/City Module Port) Fixed baud rate @ 4800 bps; for use with MRDL Digital Communicator Module or MRCTYB City Module
J1 (Service port or serial printer Fixed baud rate @ 9600 bps; 6 m (20 ft) maximum distance; for use with Service/Programming PC
port) (using Windows 95 or 98); or for serial input printer
Network Ports
Standard Protocol: 10km (33,000 feet; 6.2 miles) maximum distance between nodes, minimum 28
COM1, COM2 AWG wires (0.081 mm2);
(Secutron MR peer to peer Total panel capacity varies with programmable baud rate: up to 254 panels with 9600, 4800, and
network, redundant DCLR) 2400; up to 200 panels at 1200
RS-232 Protocol: up to 20 m (66 ft), typically for connection to external modem
Baud Rate Maximum Capacitance Maximum Network Nodes
Network Wiring Parameters 9600 100 nF 254
(maximum line resistance = 4800 220 nF 254
680 ohms) 2400 470 nF 254
1200 680 nF 200

Page 4 of 6 SECUTRON INC. Issue 2

Catalog Number 1005
Not to be used for installation purposes.
Compatible Intelligent Addressable Devices
Compatible Intelligent Addressable Devices Reference Information
Model Description
MRI-1251B Intelligent Ionization Detector
MRI-2251B Intelligent Photoelectric Detector
MRI-2251TB Intelligent Photoelectric Detector with 135°F Fixed Temperature Heat Detector
MRI-2251TMB Intelligent AcclimateTM Photo Thermal Multicriteria Smoke Detector
MRI-5251B Intelligent Heat Detector, 135°F fixed temperature
MRI-5251RB Intelligent Heat Detector, 135°F fixed temperature with rate-of-rise detection
MRI-5251H Intelligent High Temperature Heat Detector, 190°F fixed temperature
7251 Intelligent PinnacleTM Ultra High Sensitivity Laser Smoke Detector
FTX-P1 Intelligent FiltrexTM Photoelectric smoke detector
DNR Intelligent InnovairFlex Photoelectric Non-Relay Duct Smoke Detector Housing
BEAM200 Intelligent beam smoke detector with 8˝ reflector
BEAM200S Intelligent beam smoke detector with 8˝ reflector and integral sensitivity test
MRM-701ADU Intelligent Addressable Key Resettable Single Action Manual Station
MRM-710ADU Intelligent Addressable Key Resettable Dual Action Manual Station
MCP5A-RP01FG-K013-01 Intelligent Addressable Call Point (EN-54 LPCB Certified Only)
MRI-M500M Intelligent Addressable Monitor Module
MRI-M500R Intelligent Addressable Relay Module
MRI-M500S Intelligent Addressable Supervised Control Module
MRI-M501M Intelligent Addressable Mini Monitor Module
MRI-M502M Intelligent Zone Interface Module
MRI-M500X Isolator Module
MRI-M500DM Intelligent Addressable Dual Input Monitor Module
CR-6 Intelligent Addressable Six Relay Control Module
SC-6 Intelligent Addressable Six Supervised Control Module
CZ-6 Intelligent Addressable Six Conventional Zone Interface Module
IM-10 Intelligent Addressable Ten Input Monitor Module

MR-2100 & MR-2200 Back Box Dimension Reference

14-1/2" (368 mm) 7/8" (23 mm)
lip each side

Door outline reference; dimensions:

16-7/8" W x 29-1/2" H x 1-1/4" D
(429 mm x 749 mm x 172 mm)

3/4" (19 mm) lip

top and bottom
16-1/8" (410 mm)

4"
3" (76 mm) (102 mm)

5-1/4"
(133 mm)
29"
21-3/4" (740 mm)
27-1/2"
(552 mm)
(699 mm)
26-1/2"
(673 mm) 1-1/4"
(32 mm)

8-1/2"
(216 mm)

Issue 2 SECUTRON INC. Page 5 of 6

Catalog Number 1005
Not to be used for installation purposes.
Ordering Information
MR-2100 and MR-2200 Fire Alarm Control Panels
Model Description Standby Current Alarm Current
MR-2100R Single SLC Fire Alarm Control Panel, 120 VAC input, Red
MR-2100B Single SLC Fire Alarm Control Panel, 120 VAC input, Beige
110 mA 175 mA
MR-2200R Dual SLC Fire Alarm Control Panel, 120 VAC input, Red
MR-2200B Dual SLC Fire Alarm Control Panel, 120 VAC input, Beige
Backbox, Order if required prior to delivery of Fire Alarm Control Panel
MR20BOXR Backbox, Red
MR20BOXB Backbox, Beige
Note: Backbox is included with Fire Alarm Control Panels listed above, order these standalone boxes if required for early installation.
Optional Panel Modules
MRNC2* Dual NAC Expansion Module
10 mA 65 mA
(output ratings are the same as standard NACs)
MRRL4* Four Relay Module 5 mA 17 mA/relay
MRLD8 Eight (8) LED Module; Quantity 3 maximum, 2 maximum if
for Canada (Alarm current is for 3 devices in alarm, add 5 mA 15 mA
5 mA
each if more) ULC listed applications require a minimum of one (see current note)
MRDL8 LED module
MR-XPS Expansion Transformer, 120/240 VAC NA NA
MRDL** DACT Module 33 mA 60 mA
MRCTYB** City Connection Module 20 mA 20 mA
Optional Network
Port 1 Operation Port 2 Operation
Modules
MR22NTWR Standard Standard
MR22NTWR1 RS-232 Standard
MR22NTWR2 Standard RS-232
MR22NTWR12 RS-232 RS-232
* Select any combination for up to 3 modules total.
** Quantity one maximum from these modules.

Page 6 of 6 SECUTRON INC. Issue 2

Catalog Number 1005 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
ISO 9001:2000
REGISTERED
 CONVENTIONAL
FIRE ALARM CONTROL UNITS

MR-2300 SERIES Features

• Listed to UL 864, 9th edition• Available in six and
Fire Alarm Control Units twelve zone models
• Available in LED and LCD Display configurations
• LCD Display versions are equipped with a 2 line
by 20 character back-lit LCD display and numerical
keypad
• Integrated UDACT/Digital Communicator on select
models
• Front panel and PC programmable
• LED Display versions are front panel (using CFG-300
configuration tool) and PC programmable
• Remote upload/download capabilities
• Base panel is equipped with Class “B” (Style “B”)
initiating circuits which may be configured as Class
“A” (Style “D”) using a Class “A” converter module
• Initiating circuits may be configured as Alarm, Verified
Alarm, Waterflow Alarm, Sprinkler Alarm, Latching
or Non-Latching Supervisory, Monitor and Trouble-
Only
Description
• Base panel is equipped with Class “B” (Style “Y”)
Secutron’s MR-2300 Series fire alarm control panels
indicating circuits which may be configured as Class
consist of six and twelve zone models which are
“A” (Style “Z”) using a Class “A” signal converter module
equipped with a two line by 20 character back-lit
• Audible signals may be configured for Steady,
LCD display, numerical keypad and an integrated
Temporal Code, California Code and March Time
UDACT/Digital Communicator. The MR-2300 family
• Indicating Circuits may be configured as Silenceable
also includes a twelve zone model that is equipped
or Non-Silenceable for both signals and strobes
with an LED display and an integrated UDACT/Digital
• Built-in sync protocols for the following strobe
Communicator. In addition the MR-2300 Series family
manufacturers: Mircom, Amseco, System Sensor,
includes remote LCD annunciators, LED annunciators
Gentex, Faraday and Wheelock
and remote smart relay modules.
• Relay contacts for Common Alarm, Auxiliary/Alarm
The MR-2300 Series panels are ideal for both new and (Disconnectable), Common Supervisory and
retrofit applications. Designed for small to medium Common Trouble
commercial, institutional and industrial occupancies, • Configurable Signal Silence Inhibit, Auto Signal
these panels are powerful enough to meet today’s Silence and One-Man Walk Test
installation demands. The MR-2300 Series panels are • Subsequent Alarm, Supervisory, and Trouble
configurable by the keypad for onsite programming or operation
by a PC for both onsite and remote programming. Easy • RS-485 Interface for Remote LED Annunciators, LCD
to install and simple to operate and configure, the MR- Annunciators and Remote Smart Relay Modules
2300 Series panels enable the installer to configure the • Two event history logs comprised of a 200 event
system to meet their specific requirements. alarm log for alarm related events and a 200 event
general log for all other events
The MR-2300 Series panels are equipped with a 5 Amp • 5 Amp Power Supply
power supply, 4-wire resettable smoke power supply • Optional modules for additional internal relay circuits
(300mA max.) and an RS-485 interface for remote LCD and City Tie/Polarity Reversal
annunciators, LED annunciators and Remote Smart • Optional trim rings for semi-flush mounting
Relay modules.

All MR-2300 Series panels come complete with a red

door, black enclosure, durable CAT-30 lock and key
and space to mount up to 12 AH batteries. Optional MEA
approved
trim rings are available for semi-flush mounting. S6619 S6619 7165-1656:129 352-03-E
(LED Models) 7165-1656:131

Issue 4 SECUTRON Page 1 of 6

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113• Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113• E-mail: [email protected]
Catalog Number 1019 • Not to be used for installation purposes.
Features
Initiating Circuits Indicating Circuits
The MR-2300 Series panels are equipped with Class The MR-2300 Series panels are equipped with
“B” (Style “B”) initiating circuits. The initiating circuits equipped with Class “B” (Style “B”) indicating circuits.
may be configured as Class “A” (Style “D”) using an The indicating circuits may be configured as Class “A”
MR-2300-A Class “A” converter adder module. (Style “Z”) using an MR-2300-NC4 or MR-2300-NC2
Class “A” signal converter adder module. The audible
Each Initiating circuit may be configured for one of the signals may be configured for Steady, Temporal Code,
following modes of operation: California Code and March Time.

• Alarm (Without smoke detector verification) Each of the indicating circuits may be configured for
• Verified Alarm (With smoke detector one of the following modes of operation:
verification)
• Waterflow Alarm (Water flow sensors) • Silenceable Signal
• Sprinkler Alarm (Sprinkler flow sensors) • Non-Silenceable Signal
• Latching Supervisory • Silenceable Strobe
• Non-Latching Supervisory • Non-Sileneceable Strobe
• Monitor (non-latching input used mainly for
correlating to a relay circuit) The MR-2300 has built-in sync protocols for the
following strobe manufacturers; Secutron, Amseco,
• Trouble-Only (for monitoring a trouble condition System Sensor, Gentex, Faraday and Wheelock.
from an external device)

i3 Series Protocol UDACT/Digital Communicator

The MR-2300 Series panels have the i3 Series protocol The MR-2300 Series panels are equipped with a fully
built-in. The panels support the two-wire i3 Series integrated UDACT/Digital Communicator which allows
smoke detectors (2W-B/2WT-B). These i3 series for the reporting of events to a monitoring facility. The
detectors communicate with the MR-2300 to provide UDACT/Digital Communicator can be configured for
the following status information: single or dual line operation and uses the Security
Industry Association (SIA) and Ademco Contact ID
Open circuit trouble protocols. The UDACT/Digital Communicator is
This trouble indicates that loop is broken. configured via the main display and keypad on the
main panel.
Communication trouble
This trouble indicates that there is a fault in the line or In addition to its reporting functions, the integrated
the line is too noisy, the panel cannot communicate UDACT/Digital Communicator can be used to connect
with the devices. to the MR-2300 panel from remote computers for
uploading and downloading of configuration data. It
Dirty device also allows for the viewing of the event history logs.
This trouble indicates that one or more device on the The MR-2300 series panels have two event history
i3 zone is dirty. logs comprised of a 200 event alarm log for alarm
related events and a 200 event general log for all
Out of sensitivity other events.
This trouble indicates that one or more device on the
i3 zone is out of sensitivity range and cannot detect The integrated UDACT/Digital Communicator can be
an alarm condition. configured for either DACT or UDACT operation. In
DACT mode the Digital Communicator reports common
Freeze trouble alarm, trouble and supervisory information. In UDACT
This trouble indicates that a device on the i3 zone has mode the Digital Communicator reports point specific
detected a freeze condition, e.g. the temperature is information.
below 41°F / 5 °C (available only on model 2WT-B).

The built-in protocol removes the need for the 2W-MOD

Maintenance Module.

Page 2 of 6 SECUTRON Issue 4

Catalog Number 1019
Not to be used for installation purposes.
MR-2300 Series LCD Version Models

MR-2306-DDR Six Zone LCD Display Fire Alarm Control MR-2312-DDR Twelve Zone LCD Display Fire Alarm Control
Panel Panel with UDACT/Digital Communicator
The MR-2306-DDR is equipped with six Class “B” (Style “B”) The MR-2312-DDR is equipped with twelve Class “B” (Style “B”)
initiating circuits and two Class “B” (Style “Y”) indicating circuits initiating circuits and four Class “B” (Style “Y”) indicating circuits
rated @ 1.7 Amps maximum. (Total of 5 Amps) The MR-2306- @ 1.7 Amps maximum. (Total of 5 Amps). Two MR-2300-A Six
DDR is equipped with a built-in UDACT/Digital Communicator. Initiating Circuit Class A Converter Module may be used for Class
One MR-2300-A Six Initiating Circuit Class “A” Converter Modules “A” (Style “D”) wiring of the initiating circuits. One MR-2300-NC4
may be used for Class “A” (Style “D”) wiring of the initiating Four Indicating Circuit Class “A” Converter Module may be used
circuits. One MR-2300-NC2 Two Indicating Circuit Class “A” for Class “A” (Style “Z”) wiring of the Indicating circuits. The
Converter Module may be used for Class “A” (Style “Z”) wiring MR-2312-DDR has a built-in UDACT/Digital Communicator and
of the indicating circuits. The cabinet will support up to 12 AH the cabinet will support up to 12 AH batteries. The panel can
batteries. The panels can be semi-flush mounted with the optional be semi-flush mounted with the optional MR-2312-FT trim ring.
MR-2300TRB trim ring. Note: Not ULC listed. Note: Not ULC listed.
Dimensions Dimensions
MR-2306-DDR: 20”H x 14.5”W x 4.5”D MR-2312-DDR: 26”H x 14.5”W x 4.5”D
MR-2306-FT: 22.5”H x 17”W MR-2312-FT: 28.5”H x 17”W

MR-2300 Series LED Version Models

MR-2312-LDR Twelve Zone LED Display Fire Alarm Control
Panel with UDACT/Digital Communicator
The MR-2312-LDR is equipped with twelve Class “B” (Style “B”)
initiating circuits and four Class “B” (Style “Y”) indicating circuits
rated @ 1.7 Amps maximum. (Total of 5 Amps) Two MR-2300-A
Six Initiating Circuit Class “A” Converter Modules may be used for
Class “A” (Style “D”) wiring of the initiating circuits. One MR-2300-
NC4 Four Indicating Circuit Class “A” Converter Module may be
used for Class “A” (Style “Z”) wiring of the indicating circuits. The
MR-2312-LDR is configurable by the keypad (using the CFG-300
Configuration Tool) for onsite programming or by a PC for both
onsite and remote programming. The MR-2312-LDR has a built-in
UDACT/Digital Communicator and the cabinet will support up to
12 AH batteries. The panel can be semi-flush mounted with the
optional MR-2312-FT trim ring.
Dimensions
MR-2312-LDR: 26”H x 14.5”W x 4.5”D
MR-2312-FT: 28.5”H x 17”W

Issue 4 SECUTRON Page 3 of 6

Catalog Number 1019
Not to be used for installation purposes.
Remote Annunciators

MR-2306-ATR/MR-2312-ATR Remote LED Annunciators

The MR-2306-ATR and MR-2312-ATR provide 8 or 16
points respectively of LED annunciation. Both models
MR-2300-LCDR Remote LCD Annunciator feature bi-coloured LEDs which are auto-configurable
The MR-2300-LCDR provides LCD remote annunciation for either Alarm (red) or Supervisory (amber). The LED
through a 2 line by 20 character LCD display. The MR- annunciators have indicators for A.C. On, Common
2300-LCDR provides control switches for System Reset, Trouble and Signal Silence and control switches for
Signal Silence, Fire Drill and Acknowledge as well as System Reset, Signal Silence, Lamp Test and Buzzer
a numeric keypad to access the menu functions. The Silence. The MR-2306-ATR and MR-2312-ATR are
common control functions can be disabled on a per equipped with a keyswitch which allows for enabling
function basis. The MR-2300-LCDR has LED indicators and disabling of the Common Control functions. Both
models are available in a red finish and mount in a 4-gang
for A.C. On, Alarm, Supervisory, Trouble and CPU
electrical box. Note: ULC Listed as an Ancillary Device.
Fail. The MR-2300-LCDR comes complete with a red
enclosure and a CAT-30 Lock and key. Note: ULC Listed
as an Ancillary Device.

RAM-1016TZDS Remote LED Annunciator

The RAM-1016TZDS Remote LED Annunciator provides 16
points of LED annunciation. The RAM-1016TZDS comes
standard with bi-coloured LEDs which are automatically
configured for either Alarm (Red) or Supervisory (Amber)
and individual trouble LEDs. The RAM-1016TZDS has
indicators for A.C. On, Common Trouble and Signal Silence
MR-2312-SR12 Smart Relay Module and controls for System Reset, Lamp Test, Fire Drill, Buzzer
The MR-2312-SR12 provides twelve configurable relay Silence and Signal Silence. In addition it allows for the control
circuits, rated @ 28 VDC, 1 amp (resistive). Each circuit switches to be disabled on a per function basis. The RAM-
can be configured as a Normally Open (N.O.) or Normally 1016TZDS mounts in a MMX-BB-1001R enclosure.
Closed (N.C.) contact. Each relay is equipped with an
LED that is lit when the relay is energized. The relays
can be configured as relay per zone (1 to 1), Common
on Alarm, Common on Supervisory or programmable
for a logical or adjacent zone configuration. An adjacent
zone configuration will turn on an adjacent zone when
the configured zone is active. A chaining configuration CFG-300 Configuration Tool
allows for multiple relays to turn on. The MR-2312-SR12 The CFG-300 Configuration Tool is required for onsite front
panel programming of the MR-2312-LDR panel. The CFG-
is DIP switch configurable and connects to the RS-485
300 plugs into the MR-2312-LDR main board to provide a two
bus. The MR-2312-SR12 comes complete with a red
line by 20 character LCD display. The MR-2312-LDR panel
enclosure and a CAT-30 lock and key.
is configured using the CFG-300 and push buttons on the
main board. In configuration mode, the initiating and indicating
circuit disconnect buttons act as function keys. Removing the
zone labels reveals the programming function buttons. The
CFG-300 tool is used for configuration purposes only and not
for normal operation.

Page 4 of 6 SECUTRON Issue 4

Catalog Number 1019
Not to be used for installation purposes.
Adder Modules

MR-2300-A Six Initiating Circuit Class “A” Converter MR-2306-R6/MR-2312-R12 Relay Circuit Adder
Module Modules
The MR-2300-A converts six Class “B” (Style “B” initiating The MR-2306-R6 provides six configurable relay circuits,
circuits on the MR-2300 main board to Class “A” (Style “D”) rated @ 28 VDC, 1 amp (resistive). The MR-2312-R12
circuits. The MR-2300-A is equipped with wire leads to provides twelve Form C configurable relay circuits, rated @
connect to the MR-2300 main board. It mounts to the right 28 VDC, 1 amp (resistive). On both models each circuit can
of the main board Class “B” (Style “B”) initiating circuits. be configured as a Normally Open (N.O.) or Normally Closed
Two MR-2300-A modules are required to convert all twelve (N.C.) contact. Each relay is equipped with an LED that is lit
initiating circuits on an MR-2312 series panel. when the relay is energized. The relays can be configured
as relay per zone (1 to 1), Common on Alarm, Common on
Supervisory or programmable for logical or adjacent zone
configuration. An adjacent zone configuration will turn on
adjacent zone when configured zone is active. A chaining
configuration allows for multiple relays to turn on.

MR-2300-NC4 Four Indicating Circuit Class “A”

Converter Module
The MR-2300-NC4 converts four Class “B” (Style “Y”)
indicating circuits on the MR-2300 main board to Class MR-2300-PR Polarity Reversal/City Tie Module
“A” (Style “Z”) circuits. The MR-2300-NC4 is equipped The MR-2300-PR provides outputs for city box and polarity
with wire leads to connect to the MR-2300 main board. reversal applications. As a city tie module the MR-2300-PR
It mounts to the right of the main board Class “B” (Style provides an interface between the control panel indicating
“Y”) indicating circuits and is used with the MR-2312 circuits and a master box. It provides off-premises signal
series panels. transmission for systems that must comply with NFPA
requirements for Auxiliary Protective Systems. As a polarity
reversal module the MR-2300-PR provides an interface
between the control panel and a reverse polarity receiver.
It provides off-premises signal transmission for systems
that must comply with NFPA requirements.

MR-2300-NC2 Two Indicating Circuit Class “A”

Converter Module
The MR-2300-NC2 converts two Class “B” (Style “Y”) MR-2300-X Active End-of-Line Resistors
indicating circuits on the MR-2300 main board to Class The MR-2300-X are power saving End-of-Line resistors
“A” (Style “Z”) circuits. The MR-2300-NC2 is equipped which eliminates the need for an additional battery cabinet
with wire leads to connect to the MR-2300 main board. or larger batteries in order to meet the 60 hour standby
It mounts to the right of the main board Class “B” (Style requirement. (Please refer to Battery Calculation Chart in
“Y”) indicating circuits and is used with the MR-2306 manual for more details.) The MR-2300-X can also be used
series panels. when larger batteries than can fit in the cabinet are required.

Issue 4 SECUTRON Page 5 of 6

Catalog Number 1019
Not to be used for installation purposes.
Specifications
AC Input Unfiltered supply (full wave rectified)
120VAC @ 60Hz Power limited / 24VDC unfiltered / 1.7A max at 49°C
Standby Power Auxiliary Relays (Common alarm/supv/trb/ and auxiliary
24VDC standby batteries second alarm)

Charging Capability FormC / 28VDC / 1A max

4 to 12 AH Current Consumption
Indicating Circuits Model Standby Alarm
Power limited / 24VDC unfiltered / 1.7A @ 49°C per MR-2306-DDR 142 mA (112 mA*) 312 mA (282 mA*)
circuit. Maximum 5 Amps. MR-2312-DDR 174mA (104 mA*) 444mA (394 mA*)
Aux supply (non resetable)
MR-2312-LDR 164mA (104 mA*) 424mA (364 mA*)
Power limited / 22.3VDC regulated / 500mA max
4-wire smoke supply (resetable)
Power limited/22.3VDC regulated / 300mA max

Ordering Information
Model Description
Control Units
MR-2306-DDR* Six Zone LCD Display Fire Alarm Control Unit with built-in UDACT/Digital Communicator
MR-2312-DDR* Twelve Zone LCD Display Fire Alarm Control Unit with built-in UDACT/Digital Communicator
MR-2312-LDR Twelve Zone LED Display Fire Alarm Control Unit with built-in UDACT/Digital Communicator
Remote Annunciators and modules
MR-2300-LCDR Remote LCD Annunciator (Red enclosure) (Note: ULC Listed as an Ancillary Device.)
MR-2300-LCDW Remote LCD Annunciator (White enclosure) (Note: ULC Listed as an Ancillary Device.)
MR-2306-ATR Eight zone Remote LED Annunciator (Note: ULC Listed as an Ancillary Device.)
MR-2312-ATR Sixteen zone Remote LED Annunciator (Note: ULC Listed as an Ancillary Device.)
RAM-1016TZDS Sixteen zone Remote LED Annunciator with individual Trouble LEDs
MR-2312-SR12 Remote Relay Module with red enclosure
MMX-BB-1001R Red enclosure for RAM-1016TZDS
Adder Modules
MR-2300-A Six Initiating Circuit Class “A” Converter Module
MR-2300-NC4 Four Indicating Circuit Class “A” Converter Module
MR-2300-NC2 Two Indicating Circuit Class “A” Converter Module
MR-2306-R6 Six Relay Circuit Adder Module
MR-2312-R12 Twelve Relay Circuit Adder Module
MR-2300-PR Polarity Reversal/City Tie Module
MR-2300-X Active End-of-Line Resistor
Accessories
MR-2306-FT Black Semi-Flush Trim Ring for MR-2306 enclosures
MR-2312-FT Black Universal Semi-Flush Trim Ring for MR-2312 enclosures
CFG-300 Configuration Tool for MR-2312-LCDR
UIMA Universal Programming Tool
* Note: Not ULC Listed

Page 6 of 6 SECUTRON Issue 4

Catalog Number 1019 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
 REMOTE ANNUNCIATORS

MR-2644 Features
Remote LCD Annunciator • Designed to meet the requirements of NFPA 72

• UL 864 listed and CSFM listed

• 80-character (4 x 20) backlit LCD (Liquid Crystal

Display)

• Six common system status lights: Alarm (red),

Supervisory (yellow), Trouble (yellow), Monitor
(yellow), AC On (green), and Ground Fault
(yellow)

• Four system hotkeys for Ack, Silence, Reset, and

Lamp Test

• Access-controlled Silence and Reset hotkeys

– require the keyswitch to be in the “enable”
position

Description • Four sets of scroll keys for Alarm, Supervisory,

Trouble and Monitor
The MR-2644 LCD Annunciator allows you to monitor
and control compatible Fire Alarm Control Panels from • Up to eight MR-2644 annunciators can be
anywhere within your facility. Up to eight MR-2644’s, connected to the MR-2100, MR-2200 or MR-2900
each set to a unique user programmable ID, can be Fire Alarm Control Panels
connected to each FACP. A single MR-2644 can be as
far as 9000 feet (2.7 km) from the control panel. • User-programmable supervision addresses (eight
options)
The MR-2644 display follows the display of the FACP
to which it is connected allowing immediate action • Available in red or white trim to suit any
from wherever these units are installed. The on-board installation
system hotkeys provide quick access to Lamp Test and
Acknowledge functions, but require the keyswitch to • Suitable for flush mounting into a standard five
be used when accessing Silence or Reset functions. gang device box or surface mounting with optional
MR-2644-SM back box
In addition to the textual LCD, the MR-2644 incorporates
six system status LEDs that offer a quick overview of
system status. Monitored conditions include: Alarm,
Supervisory, Trouble, Monitor, AC On, and Ground
Fault.

The MR-2644 connects to an MR-2100, MR-2200,

or MR-2900 using the FACPs annunciator port.
Connection between the MR-2644 and the MR-2900
requires the use of the MR-2109-3 communications
board in the MR-2900 in order to drive Port 3.

Available to suit most indoors installations, the MR-2644

is available in either red or white and ships ready for
flush mounting. If surface mounting is required, simply MEA
order the MR-2644-SM backbox in the appropriate approved
color. S8690 Pending 7120-1656:102 352-03-E

Issue 2 SECUTRON INC. Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 1011 • Not to be used for installation purposes.
Typical Wiring Diagrams Technical Data
MR-2100 / MR-2200 Wiring Diagram (Powered by FACP) Electrical Specifications
MR-2100 / MR-2200
Voltage 16-28VDC, power limited
AUX ANN Max. Input Voltage Ripple 3.0VP-P
POWER

RXD
TXD
+ - - Standby Current Draw 30 mA
Maximum/Alarm Current 70 mA
MR-2644

+ Environmental Specifications
- Operating Temperatures 32°F – 120°F / 0°C – 49°C
RX 85% RH non-condensing
Humidity
TX (max.)

Physical Dimensions
MR-2100 / MR-2200 Wiring Diagram (Powered by 4.5” (H) x 10” (W)
external PS) MR-2644 (trim plate) 10.2cm (H) x 25.4cm (W)
MR-2100 / MR-2200
AUX ANN EXTERNAL 4.5” (H) x 10” (W) x 2½” (H)
POWER POWER SUPPLY MR-2644-SM
10.2cm (H) x 25.4cm (W) x 6.4cm (H)
(AUX)
RXD
TXD

+ - - + -

Connections
MR-2644
Maximum Distance 9000 ft. (2700m) 12 AWG
+
Communication/ 12 to 22 AWG non-shielded twisted
- Power Wire pair (two twisted pair required)
RX

TX

Note: Secutron recommends that the MR-2644 be powered

MR-2900 Wiring Diagram (Powered by FACP) from the fire panel. If an external power supply is used, the
following conditions must be met:
MR-2900
• The power supply must be regulated, filtered, power
+
AUX 1
limited, and UL listed for Fire applications.
-
MR-2644 • To ensure proper communications, the negative of the
+
AUX 2 power supply must be connected to the Aux Power
+ - negative of the fire panel.
-

RX
• The external power supply must be mounted no further
COM
LINK 3 than 10ft (3m) from the FACP.
TX
GND
* To connect the MR-2644 annunciator to a MR-2900 FACP, a
communications board must be installed in the MR-2900 (Model
#: MR-2109-3).
MR-2900 Wiring Diagram (Powered by external PS)
EXTERNAL
POWER SUPPLY
(AUX)
+ -
Ordering Information
MR-2900
Model Description
+ MR-2644R MR-2644 LCD annunciator, flush mount,
AUX 1
- Red
MR-2644
+ MR-2644G MR-2644 LCD annunciator, flush mount,
AUX 2
+ - White
-
MR-2644-SMR Surface mount backbox for MR-2644,
RX COM Red
LINK 3
TX
GND
MR-2644-SMG Surface mount backbox for MR-2644,
White

Page 2 of 2 SECUTRON INC. Issue 2

Catalog Number 1011 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
ISO 9001:2000
REGISTERED
 INTELLIGENT ADDRESSABLE DEVICES

MRI-M500 SERIES
Intelligent Modules Features
• Designed to meet a wide range of applications
• SEMS screws for easy wiring
• Panel controlled status LED (except MRI-M501M)
• Analog communications
• Rotary address switches (except MRI-M500X)
• Low standby current
• Mounts in 4” square junction box

MRI-M500X Isolator Module

The MRI-M500X Isolator Module is an automatic switch
Description that opens when the line voltage drops below four volts.
Isolator modules should be spaced between groups of
Secutron's intelligent module products are designed to
sensors or modules in a loop to protect the rest of the
meet a wide range of applications. Monitor and control
loop. If a short occurs between any two isolators, then
modules can be used to supervise and activate sounders,
both isolators immediately switch to an open circuit state
strobes, door closers, pull stations, waterflow switches,
and isolate the devices between them. The remaining
conventional smoke detectors, and more. Each module
units on the loop continue to fully operate. No more than
is rigorously designed and tested for electromagnetic
25 devices are recommended for each group.
compatibility and environmental reliability, in many cases
exceeding industry standards. Modules are addressed MRI-M502M Zone Interface Module
with easy-to-use rotary code switches. Full size modules The MRI-M502M Zone Interface Module allows
mount in standard 4" x 4" x 2-1⁄8" junction box. Wiring Secutron's intelligent panels to interface and monitor two-
terminals are easily accessible for troubleshooting wire conventional smoke detectors. All two-wire detectors
purposes. being monitored must be UL or ULC compatible with the
module. The MRI-M502M is addressed through the
MRI-M500M Monitor Module, MRI-M501M Mini
Monitor Module and MRI-M500DM Dual Input Monitor communication line of an intelligent Secutron system. It
Module transmits the status of one zone of two-wire detectors
Secutron’s monitor modules provide an interface to to the fire alarm control panel. Status conditions are
contact devices, such as security contacts, waterflow reported as normal, open, or alarm. The interface
switches, or pull stations. They are capable of Styles module supervises the zone of detectors and the
A and B supervised wiring to the load device (MRI- connection of the external power supply.
M500M is capable of Style D). Conventional 4-wire MRI-M500R Relay Module
smoke detectors can be monitored through their alarm The MRI-M500R Relay Module contains two isolated
and trouble contacts, wired as an initiating loop to the sets of Form-C contacts, which operate as a DPDT
module. In addition to transmitting the supervised switch. The module allows the control panel to switch
state of the monitored device (normal, open, or short), these contacts on command. No supervision is provided
the full analog supervision measurement is sent back for the relay contacts.
to the panel. This allows impedance changes in the
supervised loop to the monitored device to be detected.
The MRI-M500DM is capable of monitoring two separate
427-91-E
Class B circuits simultaneously, making it ideal for (MRI-M500, MRI-M500X,
waterflow tamper switch and flow switch monitoring. MRI-M501M)
87-01-E
APPROVED

The small size of the MRI-M501M allows it to fit inside S6620 S6620 7300-1656:121 (MRI-M500R, MRI-M500S)
227-03-E
devices or junction boxes behind devices. (MRI-M500DM)

Issue 2 SECUTRON INC. Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalogue Number 4003 • Not to be used for installation purposes.
MRI-M500S Control Module
The MRI-M500S Control Module provides supervised a positive indication to the panel that the control relay
monitoring of wiring to load devices that require an actually turned on. The external power supply is
external power supply to operate, such as horns, always relay isolated from the communication loop,
strobes, or bells. It is capable of Styles Y and Z so that a trouble condition on the power supply will
supervision. Upon command from the control panel, never interfere with the rest of the system. Full analog
the MRI-M500S will disconnect the supervision and measurement of the supervised wiring is transmitted
connect the external power supply across the load back to the panel and can be used to detect impedance
device. The disconnection of the supervision provides changes or other special test functions.
Specifications
General Specifications MRI-M502M Specifications
Operating Voltage Standby Current
15-32 VDC 300 µA max @ 24 VDC (one communication every 5 sec. with
Communication Line Loop Impedance LED enabled)

40 Ω max. External Power Supply

Temperature Range 18-28 VDC (100 mV ripple max.)

32° to 120°F (0° to 49°C) End-of-Line Resistance

Relative Humidity 3.9 kΩ (included)

10% to 93%: noncondensing External Supply Standby Current

Dimensions 11.5 mA @ 24 VDC (nominal)

MRI-M501M 2.7"W x 1.7:"H x 0.5"D External Supply Alarm Current

Others: 4.25"W x 4.65"H x 1.1"D 80 mA @ 24 VDC (nominal)

Shipping Weight
MRI-M500DM Specifications
M501M: 1.2 oz (37g) Others: 6.3 oz (196g)
Standby Current
750 µA max. @ 24 VDC (one communication every 5 sec. with
MRI-M500M, MRI-M500S, MRI-M501M Specifications 47k EOL)
Standby Current Alarm Current
400 µA max @ 24 VDC (one communication every 5 sec. with 970 µA max. (one communication every 5 sec.) 6 mA (with LED
47k EOL) 550 µA max @ 24 VDC (one communication every 5 latched on)
sec. with EOL<1k) 5.5 mA (with LED latched on)
End-of-Line Resistance
End-of-Line Resistance 47 kΩ (two included)
47 kΩ (included)
MRI-M500X Specifications
MRI-M500R Specifications Standby Current
Standby Current 450 µA max
300 µA @ 24 VDC (one communication every 5 sec. with LED Isolation Current
enabled)
5 mA max
LED Current
Fault Detection Delay
5.5 mA (with LED latched on) 250 ms min.
Relay Contact Ratings Fault Detection Threshold
3.0 A @ 30 VDC resistive 4 Volts
0.9 A @ 110 VDC resistive
Line Restoration Threshold
0.9 A @ 125 VAC resistive
0.5 A @ 125 VAC inductive (PF=.35) 7 Volts
0.7 A @ 75 VAC inductive (PF=.35)

Ordering Information
Model Description
MRI-M500M Monitor Module
MRI-M500R Relay Module
MRI-M500S Supervised Control Module
MRI-M501M Mini Monitor Module
MRI-501MA Mini Monitor Module (ULC listed for Canada)
MRI-M502M Zone Interface Module
MRI-M500X Isolator Module
MRI-M500DM Dual Input Monitor Module
Add suffix "A" for Canadian model.

Page 2 of 2 SECUTRON INC. Issue 2

Catalogue Number 4003 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
ISO 9001:2000
REGISTERED
 INTELLIGENT ADDRESSABLE DEVICES

MRI-200 SERIES Features

Intelligent Low Profile Detectors • Sleek, low profile design
• Detectors are equipped with a built-in analog
communications module
• Photoelectric detectors are available with additional
fixed temperature detection
• Heat detectors are available as fixed temperature
or fixed temperature with rate-of-rise detection
• Dual LEDs indicate communications and activate
steady when in alarm
• Low profile base provides easy interchangeability
• Low standby current
• Rotary address switches
• Magnetic test feature
Model MRI-2251TB Detector Mounted in a Model MRI-B210LP Base • Superior EMI protection

Description
Secutron's low profile addressable plug-in smoke
and heat detectors with integral communications
provide features that surpass conventional detectors.
Sensitivity is continuously monitored and reported
to the panel where the desired detector sensitivity Model MRI-5251B uses an innovative thermistor
can be programmed. Point ID capability allows each sensing circuit to produce 135°F fixed temperature
detector’s address to be set with decade address detection in a low profile package. These thermal
switches, providing exact detector locations for detectors provide cost effective, intelligent property
selective maintenance when chamber contamination protection in a variety of applications.
reaches an unacceptable level.
Model MRI-5251RB provides both 135°F fixed
Model MRI-2251B photoelectric smoke detector and rate-of-rise thermal detection. These thermal
provides a unique optical sensing chamber that senses detectors provide cost effective, intelligent property
smoke produced by a wide range of combustion protection in a variety of applications.
sources.
Model MRI-5251H provides 190°F (88°C) fixed
Model MRI-2251BR is a remote test capable detector temperature detection for high temperature applications.
for use with DNR(W) duct smoke detectors.
Model MRI-2251TB adds dual electronic thermistors
to the MRI-2251B to provide 135°F (57°C) fixed
temperature thermal sensing.
Model MRI-2251TMB is a photoelectric smoke detector
with supplementary 135°F thermal. Also known as
Acclimate™, it uses advanced on-board software
to combine the signals from the photo and thermal APPROVED

elements. The MRI-2251TMB is a true multicriteria S6487 S6960 7271-1656:114 148-03-E

detector capable of rejecting nuisance sources, but (MRI-1251B,

MRI-2251B/BR/TB/
(MRI-1251B,
MRI-2251B/BR/TB/
(MRI-1251B)
7272-656:112
(MRI-1251B)
219-02-E
still responding quickly to real fires. Acclimate has the TMB)
S6486
TMB)
S6974
(MIX-2251B/BR/TB/
TMB)
(MRI-2251B/TB)
390-02-E
capability of adjusting its sensitivity according to the (MRI-5251B/RB/H) (MRI-5251B/RB/H)
7270-1656:113
(MIX-5251B/RB/H)
(MRI-5251B/RB/H)

type of environment that it is installed in.

Issue 8 SECUTRON INC. Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 4000 • Not to be used for installation purposes.
Model 7251 is an intelligent, laser-based photoelectric Some ideal applications for Pinnacle include:
smoke detector featuring extensive on-board signal • Telecommunications switching facilities
processing capabilities designed to improve smoke • Cellular telephone infrastructure
response. Also known as Pinnacle™, this intelligent • Integrated circuit fabrication facilities
detector is designed to protect valuable assets and • Computer rooms
• Traffic control centers
operations where systems must remain online at all times.
• Clean rooms
Specifications
Voltage Range Thermal Ratings
15 - 32 volts DC peak Fixed Temperature Setpoint: 135°F (57°C)
Standby Current Rate of Rise Detection: 15°F/min. (8.3°C/min.)
High Temperature: 190°F (88°C)
Ion/Thermal:
150 uA @ 24 VDC (without communication, LED off) Operating Temperature Range
200 uA @ 24 VDC (one communication every 5 sec. with LED enabled) Ion/Photo: 32°F to 120°F (0°C to 49°C)
Photo/Photo with Thermal: Photo with Thermal: 32°F to 100°F (0°C to 38°C)
250 uA @ 24 VDC (without communication, LED off) Thermal: -4°F to 100°F (-20°C to 38°C)
300 uA @ 24 VDC (one communication every 5 sec. with LED enabled) High Temperature: -4°F to 150°F (-20°C to 66°C)
Pinnacle: 32°F to 100°F (0°C to 38°C)
Pinnacle:
230 μA @ 24VDC (without communication) UL Listed Velocity Range
330 μA @ 24VDC (one communication every 5 sec. with LED enabled) Ion: 0 - 1200 fpm (0 - 6.1 m/sec)
LED Current (max.) Photo/Photo with Thermal: 0 - 4000 fpm (0 - 20 m/sec)
Pinnacle: 0 - 4000 fpm (0 - 20 m/sec)
6.5 mA @ 24 VDC (on)
Insect Screen Hole Size
Height
Photo: 0.016 inch (0.41mm) nominal
2.0 inches (51 mm) Ion: 0.035 inch (0.89mm) nominal
1.66 inches (42 mm) - Pinnacle
Self Diagnostics (PinnacleTM)
Diameter
Initiated by control panel
6.1 inches (155 mm) Installed in B210LP Base Activated by test magnet
4.1 inches (104 mm) Installed in B501 Base
4.0 inches (102 mm) - Pinnacle Smoke Sensitivity (PinnacleTM)

Shipping Weight 9 levels: 0.02, 0.03, 0.05, 0.10, 0.20, 0.50, 1.00, 1.50, 2.00%/ft.
obscuration
Heat: 4.8 oz. (137 g) (0.06, 0.10, 0.16, 0.33, 0.66, 1.65, 3.24, 4.85, 6.41%/m obscuration)
Photo/Photo with Heat: 5.2 oz. (147 g)
Ion: 5.4 oz. (154 g) Drift Compensation (PinnacleTM)
Pinnacle: 5.6ox. (159 g) High sensitivity maintenance alert signal
Relative Humidity Low sensitivity maintenance alert signal
Maintenance urgent signal
10% - 93% noncondensing

Ordering Information
Addressable Detectors
Model Description
MRI-2251B Intelligent Photoelectric Detector
MRI-2251BR Intelligent Photoelectric Detector. Remote test capable. For use with DNR(W) duct detectors.
MRI-2251TB Intelligent Photoelectric Detector with 135°F Fixed Temperature Heat Detector
MRI-2251TMB Intelligent AcclimateTM Multicriteria Smoke Detector
MRI-5251B Intelligent Heat Detector, 135°F fixed temperature
MRI-5251RB Intelligent Heat Detector, 135°F fixed temperature with rate-of-rise detection
MRI-5251H Intelligent High Temperature Heat Detector, 190°F fixed temperature
7251 Intelligent PinnacleTM Laser Smoke Detector
Add suffix "A" for Canadian model.

Detector Base
Model Description
B210LP* Flanged Mounting Base; mounts on single gang box; 3-½” and 4” octagonal box; and 4”
square box with 3” mud ring
* Refer to Catalog Number 4001 for additional compatible B200 Series bases.

Page 2 of 2 SECUTRON INC. Issue 8

Catalog Number 4000 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
 PHOTOELECTRIC SMOKE DETECTORS SD SERIES

Features
• Two and four wire models

• Photoelectric smoke sensing technology

• Uses smoke sensor in conjunction with a fixed

temperature heat sensor to extend reliability

• Durable sensor head, no need for replacement

• Remote LED output on select 2-wire models

• N/C (normal close) or N/O (normal open) selectable

relay output

• Easy installation and maintenance

• Attractive sleek housing

• UL listed

Description
The SD Series photoelectric smoke detectors are All SD Series smoke detectors come equipped with
engineered to meet strict UL fire safety codes and a sleek low-profile design and durable sensor head.
effectively respond to a wide spectrum of fires. The Utilizing advanced detection and discrimination
SD Series smoke detectors are suitable for use in algorithms, the SD Series smoke detectors provide
commercial, industrial, institutional and residential quality and reliability.
occupancies. The sleek low-profile design of the
detectors emphasizes ease of installation and field
maintenance. Installation Diagram
The SD Series consists of six models:
SD-2WP / SD-2WT / SW-2WP-LED / SD-2WT-LED
The SD-2WP is a two-wire photoelectric smoke
detector for use with electrically compatible fire
alarm control units. The SD-2WT is a two-wire
smoke detector that uses photoelectric technology
in conjunction with a fixed temperature heat sensor
to further extend its sensing capabilities. Additional
two wire models (SD-2WP-LED and SD-2WT-LED)
are available with a remote LED output.
SD-4WP / SD-4WT
The SD-4WP is a four-wire photoelectric smoke
detector. The SD-4WT is a four-wire photoelectric
smoke detector with a fixed temperature heat
sensor.

S6295

5177
CATALOG NUMBER
NOT TO BE USED FOR INSTALLATION PURPOSES.
Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models.
Electrical Specifications
Standby Alarm Surge Star-Up Permissible
Heat Voltage Alarm
Model 2/4 wire Current Current Current Time Current Frequency
Sensor DC contact
(Max.) (Max.) (Max.) (Max.) (Max.)
SD-4WT 4 135°F 12/24V 370μA 35mA 60 80mA 3-5 Form A
Seconds Seconds
SD-4WP 4 12/24V 370μA 35mA 60 80mA 3-5 Form A
Seconds Seconds
SD-2WT 2 135°F 12~28V 150μA 70mA 160μA 60 80mA 3-5 —
Seconds Seconds
SD-2WP 2 12~28V 150μA 70mA 160μA 60 80mA 3-5 —
Seconds Seconds
SD-2WT-LED 2 135°F 12~28V 150μA 70mA 160μA 60 80mA 3-5 —
Seconds Seconds
SD-2WP-LED 2 12~28V 150μA 70mA 160μA 60 80mA 3-5 —
Seconds Seconds

Smoke Sensitivity 2.66+/- 1.11% FT Obscuration (UL standard)

Detection Range 50 foot rating for heat sensor
Start-Up Current 70 µA Maximum
Alarm Impedance For 2-wire models: 100Ω+3V max; 560Ω+3V max (red LED open circuit)
Reset Voltage Less than 1 volt
Reset Time Less than 1 sec
Alarm Indicator Continuously emitting red light
Temperature range -10°C to 50°C
Humidity 0 to 95% RH, non condensing
Alarm Contact For 4-wire: N/O or N/C Operation
Form A: 1.0A@30VDC/0.5A@125VAC
Dimensions 10mm (dia) x 46mm (ht) with base
Weight 130g/set with base

Ordering Information
Model Description
SD-2WP 2-wire photoelectric smoke detector. Includes 4-inch base.
SD-2WT 2-wire photoelectric smoke detector with heat sensor. Includes 4-inch base.
SD-2WP-LED 2-wire photoelectric smoke detector with heat sensor and remote LED output. Includes 4-inch base
SD-2WT-LED 2-wire photoelectric smoke detector with heat sensor and remote LED output. Includes 4-inch base.
SD-4WP 4-wire photoelectric smoke detector c/w 4-inch base
SD-4WT 4-wire photoelectric smoke detector with heat sensor c/w 4-inch base

NOT TO BE USED FOR INSTALLATION PURPOSES.

Distributed by:

Canada
25 Interchange Way
Vaughan, Ontario L4K 5W3
Telephone: (905) 660-4655
Fax: (905) 660-4113

Web page: http://www.mircom.com Email: [email protected] CAT. 5177

Rev. 2
 CONVENTIONAL DEVICES

System Sensor BEAM1224(S) Features

Single-ended Reflected Type
• 16 to 328 foot protection range
Beam Smoke Detector
• Single-ended, reflective design
• User friendly alignment procedure
• 6 user selectable sensitivity levels
• Optional integral NFPA 72 sensitivity test feature
• Removable plug-in terminal blocks
• Digital display for easy alignment
• Built-in automatic gain control compensates for sig-
nal deterioration from dust build-up
• Remote test station optional
• Paintable cover
• Easiest alignment in the industry
• Heater kits for transmitter/receiver and reflector
option

Description
System Sensor’s BEAM1224 is uniquely suited for BEAM1224 has four standard sensitivity selections, along
protecting open areas with high ceilings — areas where with two Acclimate™ settings (adjustable sensitivity).
other methods of smoke detection are difficult to install When one of the two Acclimate settings is selected,
and maintain. the detector will automatically adjust its sensitivity using
advanced software algorithms to choose the optimum
The BEAM1224 is a four-wire conventional reflected
sensitivity for the specific environment.
beam smoke detector, which is uniquely suited for
protecting open areas with high ceilings, where other BEAM1224S is also equipped with an integral sensitivity
methods of smoke detection are difficult to install and test feature, which consists of a test filter attached to a
maintain. It is to be used with UL Listed compatible servo motor inside the detector optics. When the remote
control panels only. An advantage of this single-ended test station RTS451 is used, the motor is activated and
reflective design is that it is much easier to install than moves the filter into the pathway of the light beam, to
the dual-ended projected beam detectors. Alignment test the detector’s sensitivity. This integral sensitivity test
is quickly accomplished via an optical sight and a two- feature allows the user to quickly and easily meet the
digit signal strength meter incorporated into the product. annual maintenance and test requirements of NFPA 72.
Another advantage of the BEAM1224 is that it is listed for
operation in temperatures ranging from –22°F to 131°F.
This means it can be used in open areas to provide early
warning in environments where temperature extremes may
exceed the capability of other types of smoke detectors.
BEAM1224 consists of a transmitter/receiver unit and a
reflector. When smoke enters the area between the unit
and the reflector, the smoke causes a reduction in the
signal. When the smoke level reaches the predetermined MEA
approved
threshold, an alarm is activated. APPROVED

Issue 3 SECUTRON INC. Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 2011 • Not to be used for installation purposes.
BEAM1224(S) Specifications BEAM1224(S) Parts
Operational Specifications ALIGNMENT

Protection Range 16 ft. to 328 ft. (5m to 100m)

SIGNAL
STRENGTH
Wiring Terminals
OPTICAL METER
Adjustment Angle +/– 10 Degrees horizontal & vertical GUNSIGHT ALARM COM
ALARM N.O.
(The optics move independent of the unit) HORIZONTAL
ALARM COM
ALARM N.O.
OPTICS
Sensitivity Levels Level 1 – 25% ALIGNMENT
KNOB POWER OUT (–)
Level 2 – 30% POWER OUT (+)
ALIGNMENT
Level 3 – 40%
POWER IN (–)
POWER IN (+)

Level 4 – 50% SENSITIVITY

Acclimate Level 1 – 30–50%
RESET INPUT
Acclimate Level 2 – 40–50% VERTICAL
TEST
TEST INPUT
AUX (–)
OPTICS
Fault Condition (Trouble) 96% or more obscuration blockage ALIGNMENT
REMOTE ALARM OUT
Not used
In alignment mode KNOB REMOTE TROUBLE OUT
TROUBLE COM
RESET
Improper initial alignment TROUBLE N.C.

Self-compensation limit reached

Alignment Aid Optical gunsight
Integral signal strength indication
2-digit display
Alarm Indicator Local red LED and remote alarm Advanced Test Feature
Trouble Indicator Local yellow LED and remote trouble (BEAM1224S only)
Normal Indicator Local flashing green LED
SERVO MOTOR
Test/Reset Features Integral Sensitivity Test Filter (BEAM1224S TEST FILTER
only)
Sensitivity filter (Incremental scale on
reflector) +
Local alarm test switch
Local alarm reset switch
Remote test and reset switch (Compatible
with RTS451 and RTS451KEY test station)
Smoke Detector Spacing On smooth ceilings, 30–60 feet between
projected beams and not more than one-
half that spacing between a projected beam
and a sidewall. Other spacing may be +
used depending on ceiling height, airflow
characteristics, and response requirements.
See NFPA 72. Ordering Information
Environmental Specifications
Model Description
Temperature –22°F to 131°F (–30°C to 55°C)
Humidity 10–93% RH Noncondensing BEAM1224 4 wire conventional beam smoke detector with 8˝
reflector
Electrical Specifications
BEAM1224S 4 wire conventional beam smoke detector with 8˝
Voltage 10.2 to 32 VDC (BEAM1224) reflector and integral sensitivity test
15 to 32 VDC (BEAM1224S)
BEAM1224S should not be used Add suffix “A” for Canadian models.
with 12V power sources
Accessories
Avg. Standby Current (24VDC) 17mA Max
BEAMLRK Long range accessory kit (3) additional reflectors
Avg. Current During Testing 500mA Max
(Required for applications in excess of 230 ft.
Avg. Alarm Current (24VDC) 38.5mA Max [70m])
Avg. Fault Current (24VDC) 8.5mA Max BEAMMMK Multi-mount kit (Provides ceiling or wall mount
Avg. Alignment Mode Current 28mA Max capability with increased angular adjustment for
(24VDC) either the beam or the reflector. When installed with
the transmitter/receiver unit, BEAMSMK must be
Mechanical Specifications used as well)
Detector Dimensions 10˝ H × 7.5˝ W × 3.3˝ D
BEAMSMK Surface mount kit
(254mm H × 191mm W × 84mm D)
Reflector Dimensions (16 to 230 ) 7.9˝ × 9.1˝ (200 × 230mm) BEAMHK Heater kit for transmitter/receiver unit
(See electrical requirements above)
Reflector Dimensions (beyond 230 ) 15.7˝ × 18.1˝ (400 × 460mm)
BEAMHKR Heater kit for reflector
Electrical Specifications (BEAMHK)
(See electrical requirements above)
Voltage 15 to 32V
RTS451KEY Remote test station with key lock
Current 92mA at 32V
RTS451 Remote test station used to initiate the NFPA
Power Consumption 1.6W @ 24V; 3W @ 32V
sensitivity test function
Electrical Specifications (BEAMHKR)
Voltage 15 to 32V
Current 450mA Max at 32V (per reflector)
Power Consumption 7.7W @ 24V; 15W @ 32V (per reflector)

Page 2 of 2 SECUTRON INC. Issue 3

Catalog Number 2011 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
 INTELLIGENT ADDRESSABLE DEVICES

MRM-710ADU Features
Intelligent Manual Station • Dual Action

• Key resettable

• Permanently attached Intelligent Addressable

Module

• High-gloss red enamel finish

• Plastic breakrod

• Meets ADA 5 lb. maximum manual-force

• Mounts on standard single gang box, Secutron’s
MRM-700 surface metal backbox or MRM-700WP
weather proof backbox

Description Specifications
Secutron’s MRM-710ADU provide manual fire reporting. The manual station shall be Secutron's MRM-710ADU.
This high quality, die-cast metal intelligent fire alarm Operating instructions shall be in raised English
manual station is a dual action unit with a permanently lettering and the unit shall be constructed of high
attached addressable module. The intelligent manual quality die-cast metal and finished in red enamel
station has a pair of rotary decimal switches which paint to provide quick identification. Pulling the handle
allows for two digit address setting. Pulling the handle shall initiate immediate operation of the intelligent
initiates the operation of the addressable module. addressable module. All manual fire alarm stations
The MRM-710ADU is available with CAT-30 keys and shall be installed as per the specific requirements
mount on a standard single gang backbox, Secutron outlined in the UL codes, as well as all other applicable
model MRM-700 interior surface metal backbox, or national or local codes. Final acceptance is subject to
MRM-700WP weather proof backbox. the local authority having jurisdiction.

Operation
The MRM-710ADU Dual Action Intelligent Manual
Station is operated by pushing the bar labelled “PUSH
BAR” and then pulling down the handle marked “PULL
HANDLE”. The MRM-710ADU is reset by opening the
station with the key, placing the handle in the normal
upright position and re-locking the station.

S6492 S6492 7150-1656:128 352-03-E

Issue 3 SECUTRON Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 4007 • Not to be used for installation purposes.
Specifications
Switch Rating: 1 Amp @ 30 VDC
0.1 Amp @ 125 VAC
Manual Station Dimensions: 4.9” H x 3.5” W x 2.0” D
Color: Red with raised white letters, white manual bar with raised black letters.
Current Consumption: Standby: 400 uA
Alarm: 5.5 mA

Surface Mount Backboxes

MRM-700 Surface MRM-700WP

Mount Backbox Weatherproof Surface
Mount Backbox
Dimensions:
5” H x 3.6” W x 2.0” D Dimensions:
5” H x 3.6” W x 2.2” D

Typical Wiring Diagram

MRM-710ADU
FROM
PREVIOUS
} RED } TO NEXT DEVICE
BLK
STATION
ADD.SW

BLK
- BLACK
0-9

RED

ADDRESSABLE MODULE

+ RED
~

NOTES:
1. WIRE AS SHOWN SO THAT SUPERVISION
OF CONNECTIONS IS MAINTAINED.
ADD.SW

PUR
10-99

YEL 2. MOUNT STATION TO 4" SQUARE x 1 1/2" DEEP

OUTLET BOX WITH PLASTER RING RAISED 1/2".
3. SWITCH RATING: ALL MODELS 1A @ 30VDC, 0.1A @ 125VAC
YELLOW 4. MAXIMUM WIRE SIZE: No. 12 AWG.
N.O.
5. REFER TO FIRE ALARM CONTROL PANEL MANUAL
SWITCH
FOR ADDRESSABLE MODULE SETTING.

Ordering Information
Model Description
MRM-710ADU Intelligent Addressable Key Resettable Dual Action Manual Station
MRM-700 MRM-700U Series Interior Surface Mount Backbox, Red Finish
MRM-700WP MRM-700U Series Weatherproof Surface Mount Backbox, Red Finish

Page 2 of 2 SECUTRON Issue 3

Catalog Number 4007 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
 INTELLIGENT ADDRESSABLE DEVICES

MCP5A
Intelligent Call Point

Features

• Unique ‘Plug & Play’ installation concept

• Simple rotary decade setting

• Anti-Tamper facility

• Enhanced aesthetics and compact design

• Fully approved to the latest standards

• Backward compatibility

Description

The MCP5A Intelligent Call Point is designed to be used In addition the MCP5A call point helps preserve the
with Secutron's Intelligent Fire Alarm Control Panels. integrity of the overall system as illegal removal of the
It is a dedicated addressable callpoint for installation product lid will result in the call point operating and the
on a two wire communication circuit providing both system going into alarm.
signalling of alarm to the monitoring control panel and The MCP5A may be installed as either a flush or surface
local LED indication of activation. mounted device in a normal internal environment. It
The MCP5A provides a unique ‘plug and play’concept is not intended for use in an externally exposed or
designed specifically to reduce installation time. The hazardous location.
unit utilizes a special terminal block, where all initial The MCP5A may be flush mounted to compatible
installation cabling is terminated. This terminal block is electrical boxes.
then simply connected to the back of the MCP. Simple,
but effective, with no re-termination required and no
time wasted.

The MCP5A also provides total ‘flex-ability’as it can

configured as either a break glass or resettable unit
by simply changing from one element to another. No
other additional parts or alternative products need to
be ordered.

Issue 4 SECUTRON INC. Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 5007 • Not to be used for installation purposes.
Electrical Specifications Environmental Specifications
Maximum Voltage Humidity
30VDC 0-95% non-condensing
Standby Current Operating Temperature
400 μA @ 24VDC (non-isolation) -10°C to +55°C
500 μA @ 24VDC (isolation) Storage Temperature
Operating Current -10°C to +55°C
7.6mA @ 24VDC (non-isolation) Ingress Protection (IP) Rating
7.6mA @ 24VDC (isolation)
IP24D

Dimensions
72mm
89mm 27.5mm 32mm 60mm
93mm

72mm
Mechanical Specifications Wiring Diagram

Material
PC/ABS
Weight
110g Flush
160g Surface
Color
Red, Ral301

Ordering Information
Model Description
MCP5A-RP01FG-K013-01 Intelligent Call Point
SR2T Surface mount red backbox
KG1 x 50 Call Point Break Glass. Package of 50.
SEC14-355 Secutron branded Call Point Break Glass. Package of 50.
SEC14-355SPAN Secutron branded Call Point Break Glass, Spanish. Package of 50.

Page 2 of 2 SECUTRON INC. Issue 4

Catalog Number 5007 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
 NOTIFICATION APPLIANCES

Mircom BL-6B/BL-10B Features

Motorized Steel Bells • Low current draw (20 mA)

• 6 and 10 inch diameter steel shells for long term

reliability

• RFI and EMF suppression prevents noise problems

to the fire alarm control panel

• Polarized for DC supervision

• Pigtail connection

• Standard 4 inch square electrical box mounting

• Weatherproof backbox available for outdoor

applications

• Red finish

Description Dimensions

Mircom’s BL-6B and BL-10B Motorized Steel Bells

are designed for today’s fire alarm applications. The
durable steel construction provides loud resonant tones
necessary for fire alarm installations.

The BL-6B and BL-10B bells use a varistor suppression

element to prevent RFI and EMF noise problems to
modern fire alarm control panels.

The motor used on the BL-6B and BL-10B bells

operate at a very low current (20 mA) to maximize the
number of bells per circuit. Both models are equipped
with a pigtail connection for wiring.

Both the BL-6B and BL-10B mount on a standard

4” square electrical box for indoor use or on a BB-
206WP weatherproof backbox for outdoor applications.
Mounting on a 4” octagon outlet box requires the MP-
101 Universal Mounting Plate.

S5375 S5375 7135-1477:152

Issue 1 SECUTRON INC. Page 1 of 2

Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.com
U.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: [email protected]
Catalog Number 3025 • Not to be used for installation purposes.
Installation Instructions
4“ SQUARE OUTLET BOX WIRING (REAR VIEW)
D.C. BELLS (OBSERVE POLARITY)

GASKET FOR
MOUNTING
ON SURFACE OR
STRIKER WEATHERPROOF
BACKBOX
HEX-BOLT
GONG HORIZONTAL AXIS

NO MORE NO MORE
THAN -6dB THAN -6dB

BB-206WP
WEATHERPROOF
BACKBOX

5"

Installation Instructions: Notes:

1. Remove the bell. 1. Observe polarity.
2. Wire the bell in the circuit. 2. Red wires positive (+).
3. Mount ball mechanism on 4” square standard outlet box with 3. Black wires negative (-).
the striker facing down. 4. For installation in Canada, installation must comply to
4. Replace the bell. Canadian Electrical Code, Part 1, ULC-S524-01, the standard
5. The bell must be mounted a minimum of 8 ft. above the floor, for the installation of fire alarm system, and only subject to
or as close to the ceiling as possible. final acceptance of local AHJ.
6. Polarized bell provides red(+) and black(-) lead wires. 5. For indoor use: Motor fire bell only.
When you install the bell, polarity must be observed. 6. For outdoor use: Motor fire alarm bell attached to waterproof
box only.
Caution: 7. Mounting to a 4” octagon box requires MP-101 mounting plate.
When electrical supervision is required, use in and out leads as shown.

Specifications
Model Description Voltage Rated Current Sound Level at 10 ft. dB
BL-6B 6” Motorized Steel Bell 24 VDC 20 mA 85
BL-10B 10” Motorized Steel Bell 24 VDC 20 mA 85

Ordering Informtion
Model Description
BL-6B 6” Motorized Steel Bell
BL-10B 10” Motorized Steel Bell
Accessories
BB-206WP Weatherproof Backbox
MP-101 Universal Mounting Plate
M-1995 Yard Hood
SG-206 Grill for 6” Bell Boxes
SG-206S Brushed Stainless Steel Grill for 6” Bell Backbox
SG-210 Grill for 10” Bell Backbox
SG-210S Brushed Stainless Steel Grill for 10” Backbox

Page 2 of 2 SECUTRON INC. Issue 1

Catalog Number 3025 • Not to be used for installation purposes.
Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.
Modul-R® is a trademark of Secutron Inc.
ISO 9001:2000
REGISTERED
 WALL MOUNT HORN/STROBES FHS-340 SERIES

Features
• UL and C-UL listed
• 12 VDC with 15, 35 or 60 cd settings
• 24 VDC with 15, 35, 60, 75, 95 or 110 cd settings
• 6 distinct candela settings
• Candela selection view window
• 15/75 ADA compliant on 60cd setting
• 33 sound output settings
• Horn or chime sound output
• Pre-wire back plate
• Universal back plate mounting (single gang, double
gang,  octagon, or 4” square)
• Single screw mounting
• For indoor applications

Description Engineering Specifications

The FHS-340 Horn/Strobe Series provides a wide The installer shall provide and install the FHS-340
range of candela light output options in a single device. selectable horn/strobe. The strobe shall have six
The candela settings include a 12 or 24 volt DC (6) candela settings. The candela settings shall be
operation for the 15, 35 and 60 (75 on axis) candela selectable using a drum roller and shall display the
settings and 24 volt DC operation for the 15, 35, 60, candela setting on the front of the device. The horn
75, 95 and 110 candela settings. The candela setting shall have 33 selectable settings configurable by
is displayed through the front window and is selectable dip switches. The sounder shall be capable of ANSI
using a drum wheel. Temporal Code 3, March Time and produce a chime
The horn settings include Temporal, Non-Temporal, output. The horn shall have three distinct volume
March Time and a Chime sound. The horn also has levels. The horn/strobe shall operate at 12 or 24 VDC
Low, Mid and High volume settings for each pattern and regulated or full wave rectified. The horn/strobe shall
tone. The tones include 2400 Hz, Electro-Mechanical, have an operating range between 8 and 33 VDC. The
Broadband and Chime. strobes can be synchronized using a control panel
with the Mircom sync protocol or the SDM-240 sync
The voltage input can be either regulated DC or full module. The strobe shall utilize a mounting plate that
wave rectified (FWR) 12 volt or 24 volt operation with allows the installer to pre-wire the mounting plate.
an operating range from 8 to 33 V DC. The strobes The mounting plate shall be universal and mount on
can be synchronized using a control panel with the a single gang, double gang, octagon or 4 inch square
Mircom (Amseco) sync protocol or an SDM-240 sync box. The mounting plate shall be completely covered
module. by the strobe and shall be secured by a single screw.
The FHS-340 utilizes a universal mounting plate that The strobe shall be UL listed to standard 1638, General
will mount on a single gang, double gang, octagon Signaling, and standard 1971, Signaling Devices for the
and 4” square electrical boxes. The back plate allows Hearing Impaired. In addition, the strobes shall be C-UL
the installer to mount the plate and connect the wire listed to CAN-ULC S526. The horn shall be UL listed to
connections. The strobe attaches in a hinge fashion standard 464, Audible Signaling Devices.
from the top and is secured by a single mounting screw.
The strobe completely covers the mounting back plate,
therefore it can be mounted before other trades work
is completed and not affect the final look. S5375

5269
CATALOG NUMBER
NOT TO BE USED FOR INSTALLATION PURPOSES.
Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models.
 Installation

A jumper plug is provided to test for correct

wiring in the supervisory mode only. Do not
pass alarm current through the jumper.

Note: Installation must comply in accordance

with applicable standards.

Selector Switch

Dimensions Light Output

Inches (mm) Light output in precentage when measured from the following directions per UL 1971.
6 5/64 (154.4)

5 (127)
2 5/16 (59)

High voltage may be present inside the light assembly even though power is not
connected. If access to the component board is required (removal or replacement), the
capacitor must be discharged by touching a wire to both ends of the flash tube.
DO NOT attempt to touch or move the assembly until the capacitor has been
discharged.

Specifications Dipswitch Settings

Strobe Current Horn Dipswitch
Light Max. RMS Operating Current (mA RMS) Pattern ON

Output Reg. 12 VDC Reg. 12 FWR Reg. 24 VDC Reg. 24 FWR 1 ON - Non-temporal
15cd 116 152 62 99 1 OFF - Temporal 1 2 3 4 5 6 7 8

35cd 209 267 102 152 Both 2 = OFF

60/75cd 254 258 131 190 1 and 2 ON = March Time
75cd NA NA 146 208 Tone
95cd NA NA 177 243 3 and 4 ON = 2400Hz
110cd NA NA 196 268 3 ON and 4 OFF = Electromechanical
3 and 4 OFF = Chime
Voltage 12/24V 3 OFF and 4 ON = Broadband
UL Designation Regulated 12 DC/FWR Regulated 24 DC/FWR
Volume
Operating Voltage
8 - 17.5V 16 - 33V 5 and 6 ON = High
Range
Flash Rate 60 times/min. 5 ON and 6 OFF = Mid

Sync Module (SDM-240) N/A Available

5 and 6 OFF = Low
7 and 8 ON = Horn/strobe on 2 wires
Operating Temperature
Indoor model: 32°F to 120°F (0°C to 49°C)
Range 7 and 8 OFF = Horn and strobe on 4 wires

CAT. 5269
NOT TO BE USED FOR INSTALLATION PURPOSES. page 2 of 4
Specifications
Non-Temporal Horn Current
dBA Anechoic
dBA Reverberant
Max. RMS Operating Current Ratings per
Ratings per UL464
(mA RMS Current) CAN/ULC S525
Pattern Volume (dBA @ 10 ft.)
(dBA @ 10 ft.)
Reg 12 Reg 12 Reg 24 Reg 24 Reg 12 Reg 24 Reg 12 Reg 24
VDC FWR VDC FWR VDC/FWR VDC/FWR VDC/FWR VDC/FWR
High 119 79 87 125 87 87 99 100
2400 Hz Mid 44 46 28 74 82 82 94 96
Low 30 30 18 41 79 80 92 92
High 118 77 81 121 86 87 100 100
Electro-Mechanical Mid 43 43 26 67 82 84 96 97
Low 27 29 16 36 79 80 93 93
High 146 125 78 148 86 86 101 102
Broadband Mid 41 63 26 64 81 82 96 98
Low 28 40 16 39 77 79 94 95
High 27 35 21 27 70 70 86 86
Chime Mid 11 15 8 13 62 62 79 80
Low 9 11 7 12 58 57 75 75

Temporal Horn Current

dBA Anechoic
dBA Reverberant
Max. RMS Operating Current Ratings per
Ratings per UL464
(mA RMS Current) CAN/ULC S525
Pattern Volume (dBA @ 10 ft.)
(dBA @ 10 ft.)
Reg 12 Reg 12 Reg 24 Reg 24 Reg 12 Reg 24 Reg 12 Reg 24
VDC FWR VDC FWR VDC/FWR VDC/FWR VDC/FWR VDC/FWR
High 124 70 87 132 82 82 100 100
2400 Hz Mid 46 38 30 83 77 79 95 96
Low 30 28 18 36 74 75 92 92
High 114 69 80 134 83 82 100 101
Electro-Mechanical Mid 42 40 27 67 78 80 95 96
Low 28 27 16 36 75 76 93 93
High 151 117 80 146 82 82 101 102
Broadband Mid 45 59 26 73 77 78 97 98
Low 30 42 16 31 75 76 94 95
High 29 35 21 28 68 70 86 86
Chime Mid 10 17 9 12 61 61 79 79
Low 9 12 8 9 55 55 75 76

March Time Horn Current

dBA Anechoic
dBA Reverberant
Ratings per
Max. RMS Current (mA RMS Current) Ratings per UL464
CAN/ULC S525
Pattern Volume (dBA @ 10 ft.)
(dBA @ 10 ft.)
Reg 12 Reg 12 Reg 24 Reg 24 Reg 12 Reg 24 Reg 12 Reg 24
VDC FWR VDC FWR VDC/FWR VDC/FWR VDC/FWR VDC/FWR
High 121 70 92 132 83 84 99 100
2400 Hz Mid 47 39 31 76 79 81 95 96
Low 36 25 19 35 76 77 92 92
High 114 69 86 125 83 83 100 100
Electro-Mechanical Mid 42 37 27 67 80 81 95 96
Low 30 26 19 37 77 77 92 93
High 153 121 77 126 83 84 101 102
Broadband Mid 42 55 28 56 79 80 97 98
Low 29 42 16 26 76 77 94 95

CAT. 5269
NOT TO BE USED FOR INSTALLATION PURPOSES. page 3 of 4
Wiring Diagram

FHS-340

(FHS-340) FHS-340
SDM-240

SDM-240

SDM-240

Ordering Information
Model Number Description
FHS-340R Wall Mount Horn/Strobe, Red
FHS-340W Wall Mount Horn/Strobe, White

NOT TO BE USED FOR INSTALLATION PURPOSES.

Distributed by:

Canada U.S.A.
25 Interchange Way 4575 Witmer Industrial Estates
Vaughan, Ontario L4K 5W3 Niagara Falls, NY 14305
Telephone: (905) 660-4655 Toll Free: (888) 660-4655
Fax: (905) 660-4113 Fax Toll Free: (888) 660-4113

Web page: http://www.mircom.com Email: [email protected]

CAT. 5269
Rev. 1