07QX84XX-E02-D785-00004

Page
PROJECT SPECIFIC 1 of 6
Phillips 66 Lake Charles
ADDENDUM ADDENDUM
Distillate Upgrade HDS Project TO Revision: B - IFA Date: 4/23/20

Site / Worley Job Number REP PIPING CLASS SUPERCEDES

Westlake, LA / 07-QX84-XX BAAA1 Revision: A - IFA Date: 2/4/20

Issuing Department: Prepared By: Checked By:

Piping Engineering D. Perniciaro N. Prado
Reviewed By: Project Approval: Client Approval:
G. Castello GCC W. Creel

This Addendum is issued in addition to the Phillips 66 REP Piping Class (referenced above) and should be
treated as the prevailing document where topics are in conflict. The original Line Class Specification is
attached and exceptions, additions, clarifications, revisions, etc. are noted below. Changes in accordance
with the current revision are reflected in bold text.

1 GENERAL:

1.1 Per Lake Charles site preference, buttweld and flanged components shall be used at
NPS 2 in lieu of socket weld components.

1.2 When used in Hydrogen service (partial pressure of Hydrogen 50 psia or greater),
PWHT is required when the design temperature is above 450°F.

1.3 Components larger than NPS 24 shall not be used without engineering approval.

1.4 Apply the following note to pipe and wrought (A234) fittings at thickness > 0.500”: “Impact
Tested per ASME B31.3 at -20°F.”

2 VALVES:

2.1 Only the following valves are approved for use on the project:
GATE VALVES
COMPCODE SIZE RATING DESCRIPTION NOTES
CS, ASTM A105, Gate, OS&Y, Reduced Port, Solid Wedge, ASME
V01GS6302101 ½ - 1½ 300 B16.5 Flanged (Raised Face), Integral with Body, 13% Cr Trim with V01
Stellite Body Seat (API #8), 13 Cr Stem, Handwheel Operator
CS, ASTM A105, Gate Valve, OS&Y, Reduced Port, Solid Wedge
V01GSRJ02101 ½ - 1½ 800 Socket Weld, 13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem, Handwheel Operator
CS, ASTM A105, Gate Valve, OS&Y, Reduced Port, Solid Wedge,
V01GSUJ02101 ½ - 1½ 800 Socket Weld / Female Pipe Thread, 13% Cr Trim with Stellite Body 2.2
Seat (API #8), 13 Cr Stem, Handwheel Operator
CS, ASTM A105, Gate Valve, OS&Y, Full Port, Solid Wedge, Socket
V01GURJ02101 ½ - 1½ 800 Weld, 13% Cr Trim with Stellite Body Seat (API #8), 13% Cr Trim with V05
Stellite Body Seat (API #8),13 Cr Stem, Handwheel Operator
CS, ASTM A216 Grade WCB, Gate, OS&Y, Full Port, Flexible Wedge,
V02GA6302101 2-8 300 ASME B16.5 Flanged (Raised Face), Integral with Body, 13% Cr Trim
with Stellite Body Seat (API #8), 13 Cr Stem, Handwheel Operator
CS, ASTM A216 Grade WCB, Gate, OS&Y, Full Port, Flexible Wedge,
V02GA6302101 10 - 24 300 ASME B16.5 Flanged (Raised Face), Integral with Body, 13% Cr Trim
with Stellite Body Seat (API #8), 13 Cr Stem, Gear Operator
 07QX84XX-E02-D785-00004
Page
PROJECT SPECIFIC 2 of 6
Phillips 66 Lake Charles
ADDENDUM ADDENDUM
Distillate Upgrade HDS Project TO Revision: B - IFA Date: 4/23/20

Site / Worley Job Number REP PIPING CLASS SUPERCEDES

Westlake, LA / 07-QX84-XX BAAA1 Revision: A - IFA Date: 2/4/20

Issuing Department: Prepared By: Checked By:

Piping Engineering D. Perniciaro N. Prado
Reviewed By: Project Approval: Client Approval:
G. Castello W. Creel

GLOBE VALVES
COMPCODE SIZE RATING DESCRIPTION NOTES
CS, ASTM A105, Globe Valve, OS&Y, Socket Weld, 13% Cr Trim with
V01GLRJ02101 ½ - 1½ 800
Stellite Body Seat (API #8), 13 Cr Stem, Handwheel Operator
CS, ASTM A105, Globe Valve, OS&Y, Socket Weld / Female Pipe
V01GLUJ02101 ½ - 1½ 800 Thread, 13% Cr Trim with Stellite Body Seat (API #8),13 Cr Stem,
Handwheel Operator
CS, ASTM A216 Grade WCB, Globe Valve, OS&Y, ASME B16.5
V02GL6302101 2-4 300 Flanged (Raised Face), Integral with Body, 13% Cr Trim with Stellite V06
Body Seat (API #8), 13 Cr Stem, Handwheel Operator

CHECK VALVES
COMPCODE SIZE RATING DESCRIPTION NOTES
CS, ASTM A105, Check Valve, Horizontal Lift Piston Spring Assisted,
V01CPRJ02001 ½ - 1½ 800
Socket Weld, 13% Cr Trim w/ Stellite Body Seat (API # 8), 13 Cr Stem
CS, ASTM A216 Grade WCB, Check Valve, Swing Type, ASME B16.5
V02CS6302001 2 - 24 300 Flanged (Raised Face), Integral with Body,13% Cr Trim with Stellite V58
Body Seat (API #8), 13 Cr Stem
CS, ASTM A216 Grade WCB, Check Valve, Lug Body, Through Drilled,
V02CU6302001 2 - 10 300 Dual Disc, Interface with ASME B16.5 Flanged (Raised Face), 13% Cr V16, V44, V57, 2.3
Trim with Stellite Body Seat (API #8), 13 Cr Stem
CS, ASTM A216 Grade WCB, Check Valve, Dual Plate, Double
V02DC6301001 12 - 24 300 Flanged, ASME B16.5 Flanged (Raised Face), 13% Cr Trim with 2.3
Stellite Body Seat (API #8)

2.2 V01GSUJ02101 with nipple shall be the default for vent, drain, and instrument
applications.

2.3 V02CS6302001 shall be the default check valve for NPS 2 - 24.

2.4 Valves needed for Hot Taps shall be ordered as Piping Specialty Items.

3 PIPING:

4 PIPE NIPPLES:
5 FITTINGS:

5.1 Unions (30162M0000) shall not be used.

 07QX84XX-E02-D785-00004
Page
PROJECT SPECIFIC 3 of 6
Phillips 66 Lake Charles
ADDENDUM ADDENDUM
Distillate Upgrade HDS Project TO Revision: B - IFA Date: 4/23/20

Site / Worley Job Number REP PIPING CLASS SUPERCEDES

Westlake, LA / 07-QX84-XX BAAA1 Revision: A - IFA Date: 2/4/20

Issuing Department: Prepared By: Checked By:

Piping Engineering D. Perniciaro N. Prado
Reviewed By: Project Approval: Client Approval:
G. Castello W. Creel

5.2 Revise BLE/PSE swages and add BLE/TSE, PLE/TSE and PBE swages as follows:
FITTINGS
SMALL
COMPCODE SCH. DESCRIPTION NOTES
END SIZE
FITTING: CS, ASTM A234 Grade WPB, Concentric Swage,
201G700D00 ½ - 1½ 160 F03, 15.1
Beveled Large End / Threaded Small End
FITTING: CS, ASTM A234 Grade WPB, Eccentric Swage, Beveled
201H700D00 ½ - 1½ 160 F03, 15.1
Large End / Threaded Small End
FITTING: CS, ASTM A234 Grade WPB, Concentric Swage, Plain
201GM00D00 ½-1 160 F03, 15.1
Large End / Threaded Small End
FITTING: CS, ASTM A234 Grade WPB, Eccentric Swage, Plain
201HM00D00 ½-1 160 F03, 15.1
Large End / Threaded Small End
FITTING: CS, ASTM A234 Grade WPB, Concentric Swage, Plain
201G4000200 ½-1 XS F03, 15.1
Both Ends
FITTING: CS, ASTM A234 Grade WPB, Eccentric Swage, Plain
201H4000200 ½-1 XS F03, 15.1
Both Ends
FITTING: CS, ASTM A234 Grade WPB, Concentric Swage,
201GS00200 ½ - 1½ XS F03, 15.1
Beveled Large End / Plain Small End
FITTING: CS, ASTM A234 Grade WPB, Eccentric Swage, Beveled
201HS00200 ½ - 1½ XS F03, 15.1
Large End / Plain Small End

5.3 Thredolet COMPCODE 301B3MSR00 for NPS ½ - 1 are not allowed for use on this
project and should be purchased as Piping Specialty Items when needed. Revise
fittings as follows:
FITTINGS
SMALL SCH./
COMPCODE DESCRIPTION NOTES
END SIZE RTG
301B3NSR00 ½-1 6000 FITTING: CS, ASTM A105, Thredolet, Threaded, Specify Run Size F05, F66
301B3MSR00 1½ 3000 FITTING: CS, ASTM A105, Thredolet, Threaded, Specify Run Size F05, F66
301Y2M0000 ½-1 3000 FITTING: CS, ASTM A105, Reducing Tee, Socket Weld
FITTING: CS, ASTM A105, Reducing Tee, Socket Weld x Socket
301Y6M0000 ½-1 3000
Weld x Threaded
FITTING: CS, ASTM A105, Weldolet, Buttweld, Specify Run Size
301K50SSB2 2 XS F25, F67
and Run Schedule (match Pipe Schedule of Class), Branch = XS
FITTING: CS, ASTM A234 Grade WPB, Reducing Tee, Butt Weld,
201X100200 2 XS P31
Branch = XS
FITTING: CS, ASTM A234 Grade WPB, Reducing Tee, Butt Weld,
201X100100 3 - 12 Std Wt
Branch = Std Wt
FITTING: CS, ASTM A234 Grade WPB, Reducing Tee, Butt Weld,
201X100200 14 - 18 XS
Branch = XS
FITTING: CS, ASTM A234 Grade WPB, Reducing Tee, Butt Weld,
201X100-0- 20 - 24 Calc.
Branch = Calc
 07QX84XX-E02-D785-00004
Page
PROJECT SPECIFIC 4 of 6
Phillips 66 Lake Charles
ADDENDUM ADDENDUM
Distillate Upgrade HDS Project TO Revision: B - IFA Date: 4/23/20

Site / Worley Job Number REP PIPING CLASS SUPERCEDES

Westlake, LA / 07-QX84-XX BAAA1 Revision: A - IFA Date: 2/4/20

Issuing Department: Prepared By: Checked By:

Piping Engineering D. Perniciaro N. Prado
Reviewed By: Project Approval: Client Approval:
G. Castello W. Creel

6 FLANGES:

7 ORIFICE FLANGES:

8 GASKETS:

9 BOLTING:

9.1 Add and revise bolting as follows:

BOLTING
COMPCODE SIZE RATING DESCRIPTION NOTES
BOLTING: ASTM A193 Grade B7 / ASTM A194 Gr. 2H, Stud Bolts TDES ≤ 500°F
80220000U1 ½ - 24 -
with 2 Heavy Hex Nuts, Teflon Coated B02, B06, 15.3
BOLTING: ASTM A193 Grade B7 / ASTM A194 Gr. 2H, Stud Bolts TDES > 500°F
8022000000 ½ - 24 -
with 2 Heavy Hex Nuts B02, B06, 15.3

9.2 Add hardened washers for bolt assemblies over 1⅛” stud diameter and larger as
follows:

BOLTING
COMPCODE SIZE RATING DESCRIPTION NOTES
WASHER: CS, Through-Hardened per ASTM F436 (Type 1) (to be
8M1W000000 ½ - 24 -
used with A193 Grade B7 bolt / A194 Grade 2H nut)

10 LINE BLANKS:

10.1 Corrosion allowance for in-line blanks shall be reduced to 0.019”, as calculated per
ASME B16.48 dimensions. DELETED

10.2 Only the following line blanks and spacers are approved for use on this project.
Revise line blanks and spacers as follows:
LINE BLANKS
COMPCODE SIZE RATING DESCRIPTION NOTES
BLIND: CS, ASTM A516 Grade 70, Figure 8 Blank, ASME B16.48,
5051630000 1-2 300
Raised Face, ASME B16.5, Class 300
BLIND: CS, ASTM A516 Grade 70N (Normalized), Figure 8 Blank,
5051630000 4 - 10 300
ASME B16.48, Raised Face, ASME B16.5, Class 300
BLIND: CS, ASTM A516 Grade 70N (Normalized), Paddle Blank,
5052630000 14 - 20 300
ASME B16.48, Raised Face, ASME B16.5, Class 300
 07QX84XX-E02-D785-00004
Page
PROJECT SPECIFIC 5 of 6
Phillips 66 Lake Charles
ADDENDUM ADDENDUM
Distillate Upgrade HDS Project TO Revision: B - IFA Date: 4/23/20

Site / Worley Job Number REP PIPING CLASS SUPERCEDES

Westlake, LA / 07-QX84-XX BAAA1 Revision: A - IFA Date: 2/4/20

Issuing Department: Prepared By: Checked By:

Piping Engineering D. Perniciaro N. Prado
Reviewed By: Project Approval: Client Approval:
G. Castello W. Creel

BLIND: CS, ASTM A516 Grade 70N (Normalized), Paddle Spacer,

5053630000 14 - 20 300
ASME B16.48, Raised Face, ASME B16.5, Class 300

11 SPECIALTY COMPONENTS:

11.1 Remove Y-Type Strainers. They shall be ordered as Piping Specialty Items.

12 PIPING INSTRUMENT CONNECTIONS:

13 EQUIPMENT INSTRUMENT CONNECTIONS:

14 BRANCHES:

14.1 Revise NPS ¾ - 2 (header) x NPS ½ - 1½ (branch) branch connection Reducing Tee to
NPS ¾ - 1½ (header) x NPS ½ - 1 (branch).

14.2 Revise NPS 3 - 48 (header) x NPS ½ - 1½ (branch) branch connection Sockolet/Elbolet

to NPS 2 - 24 (header) x NPS ½ - 1½ (branch).

14.3 Revise NPS 4 - 48 (header) x NPS 2 (branch) branch connection to Weldolet in lieu of
Sockolet/Elbolet.

14.4 NPS ≥ 12 branch connections made with a Weldolet shall be PWHT.

15 NOTES:

15.1 Revise note F03 as follows:

Use swages where small end is NPS 1½ and smaller, use weld reducer where small end
is NPS 2 and larger.

15.2 Revise note F41 as follows:

Any unused pressure tap shall be plugged (per ASME B16.11) and socket welded.

15.3 Teflon coated bolts should be used up to 625°F if flanges are uninsulated.
 07QX84XX-E02-D785-00004
Page
PROJECT SPECIFIC 6 of 6
Phillips 66 Lake Charles
ADDENDUM ADDENDUM
Distillate Upgrade HDS Project TO Revision: B - IFA Date: 4/23/20

Site / Worley Job Number REP PIPING CLASS SUPERCEDES

Westlake, LA / 07-QX84-XX BAAA1 Revision: A - IFA Date: 2/4/20

Issuing Department: Prepared By: Checked By:

Piping Engineering D. Perniciaro N. Prado
Reviewed By: Project Approval: Client Approval:
G. Castello W. Creel

REVISION HISTORY

Rev. A dtd 2/4/20 – Pipe spec addendum created for project use. Issued for Approval.

Rev. B dtd 4/23/20 – Revised notes 2.1, 5.2, 5.3, 9.2 and 10.2. Added note 1.2. Deleted note 10.1.
Issued for Approval.
 September 2019
Revision 3.2

REP Piping Classes

BAAA1 SERVICE: Hydrocarbons, and/or Hydrogen Service

RATING: 300 CORROSION ALLOWANCE: 0.065"
FACING: Raised Face PRESSURE LIMIT: Per ASME B16.5
INSTR. CLASS: I-1 TEMPERATURE LIMIT: -20F to 750F
MATERIAL: CS - PWHT if wall thk.> 1-1/2" thk., minimum preheat of 200F for 1"-1-1/2" thk.

DESIGN NOTES:
Operation up to 800F is allowed with Owners Engineer Approval. Consideration for relevant damage mechanisms is required
and may limit the design temperature (ex. hydrogen service, caustic service, etc.).
Special considerations are required for operation in the creep regime (ex. discontinuities around supports). The creep regime is
defined per material specification by the Time-Dependent Properties notes (T1 thru T10) in ASME Section II Part D Table 1A.
The Minimum Design Metal Temperature of this pipe class is based on the schedules listed within, see REP 5-1-1 Paragraph 4.2
for Minimum Design Metal Temperature requirements.
Seal Welding: REP 5-5-3
Stress Relief: REP 5-5-1
Design & Selection: REP 5-1-1, REP 5-1-2 & REP 5-2-1
Fabrication: REP 5-5-1
Erection: REP 5-5-3
Gaskets: REP 5-2-2
Flange finish shall be 125 - 250 AARH.

GATE VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
V01GS6302101 1/2 - 2 300 CS, ASTM A105,Gate, OS&Y, Reduced Port, Solid V01
Wedge,ASME B16.5 Flanged (Raised Face), Integral with
Body,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V01XS6302101 1/2 - 2 300 CS, ASTM A105,Bellows Seal Gate, OS&Y, Reduced Port, V01, V107
Solid Wedge,ASME B16.5 Flanged (Raised Face), Integral
with Body,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V01GSUJ02101 1/2 - 2 800 CS, ASTM A105,Gate, OS&Y, Reduced Port, Solid V25
Wedge,Socket Weld / Female Pipe Thread,13% Cr Trim with
Stellite Body Seat (API #8), 13 Cr Stem,Handwheel Operator
V01GSRJ02101 1/2 - 2 800 CS, ASTM A105,Gate, OS&Y, Reduced Port, Solid
Wedge,Socket Weld,13% Cr Trim with Stellite Body Seat (API
#8), 13 Cr Stem,Handwheel Operator
V01GEYJ02101 1/2 - 1 1/2 800 CS, ASTM A105,Gate Valve, Extended Body, OS&Y,Male F05, V95
Pipe Thread ASME B16.11 / Female Pipe Thread ASME
B16.11,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V01GE5J02101 1/2 - 2 800 CS, ASTM A105,Gate Valve, Extended Body, OS&Y,Integrally V32, V70, V71
Reinforced Extended Male Lip / Female Pipe Thread ASME
B16.11,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V01GEPJ02101 1/2 - 2 800 CS, ASTM A105,Gate Valve, Extended Body, OS&Y,Male V25
Socketweld ASME B16.11 / Female Pipe Thread ASME
B16.11,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V01GEDJ02101 1/2 - 2 800 CS, ASTM A105,Gate Valve, Extended Body, OS&Y,Integrally V32, V69, V70
Reinforced Extended Male Butt Weld ASME B16.25 / Female
Pipe Thread ASME B16.11,13% Cr Trim with Stellite Body
Seat (API #8), 13 Cr Stem,Handwheel Operator
V01XSUJ02101 1/2 - 2 800 CS, ASTM A105,Bellows Seal Gate, OS&Y, Reduced Port, V25, V107

Page 551/2074
 September 2019
Revision 3.2

REP Piping Classes

Solid Wedge,Socket Weld / Female Pipe Thread,13% Cr Trim

with Stellite Body Seat (API #8), 13 Cr Stem,Handwheel
Operator
V01XSRJ02101 1/2 - 2 800 CS, ASTM A105,Bellows Seal Gate, OS&Y, Reduced Port, V107
Solid Wedge,Socket Weld,13% Cr Trim with Stellite Body Seat
(API #8), 13 Cr Stem,Handwheel Operator
V01XEYJ02101 1/2 - 1 1/2 800 CS, ASTM A105,Gate Valve, Bellows Seal, Extended Body, F05, V95
OS&Y,Male Pipe Thread ASME B16.11 / Female Pipe Thread
ASME B16.11,13% Cr Trim with Stellite Body Seat (API #8),
13 Cr Stem,Handwheel Operator
V01XE5J02101 1/2 - 2 800 CS, ASTM A105,Gate Valve, Bellows Seal, Extended Body, V32, V70, V71,
OS&Y,Integrally Reinforced Extended Male Lip / Female Pipe V107
Thread ASME B16.11,13% Cr Trim with Stellite Body Seat
(API #8), 13 Cr Stem,Handwheel Operator
V01XURJ02101 1/2 - 2 800 CS, ASTM A105,Gate Valve, Bellows Seal, Full Port, OS&Y, V05, V107
Solid Wedge,Socket Weld,13% Cr Trim with Stellite Body Seat
(API #8), 13 Cr Stem,Handwheel Operator
V01GURJ02101 1/2 - 2 800 CS, ASTM A105,Gate, OS&Y, Full Port, Solid Wedge,Socket V05
Weld,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V02GA6302101 3-8 300 CS, ASTM A216 Grade WCB,Gate,OS&Y, Full Port, Flexible
Wedge,ASME B16.5 Flanged (Raised Face), Integral with
Body,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V02XA6302101 3-8 300 CS, ASTM A216 Grade WCB,Bellows Seal Gate, OS&Y, Full V107
Port, Flexible Wedge,ASME B16.5 Flanged (Raised Face),
Integral with Body,13% Cr Trim with Stellite Body Seat (API
#8), 13 Cr Stem,Handwheel Operator
V02GA6302201 10 - 24 300 CS, ASTM A216 Grade WCB,Gate,OS&Y, Full Port, Flexible
Wedge,ASME B16.5 Flanged (Raised Face), Integral with
Body,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Gear Operator
V02XA6302201 10 - 24 300 CS, ASTM A216 Grade WCB,Bellows Seal Gate, OS&Y, Full V107
Port, Flexible Wedge,ASME B16.5 Flanged (Raised Face),
Integral with Body,13% Cr Trim with Stellite Body Seat (API
#8), 13 Cr Stem,Gear Operator

GLOBE VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
V02GL6302101 3-4 300 CS, ASTM A216 Grade WCB,Globe Valve,OS&Y,ASME V06
B16.5 Flanged (Raised Face), Integral with Body,13% Cr Trim
with Stellite Body Seat (API #8), 13 Cr Stem,Handwheel
Operator
V02XL6302101 3-4 300 CS, ASTM A216 Grade WCB,Bellows Seal Globe Valve, V06, V107
OS&Y,ASME B16.5 Flanged (Raised Face), Integral with
Body,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator
V01GLUJ02101 1/2 - 2 800 CS, ASTM A105,Globe Valve,OS&Y,Socket Weld / Female
Pipe Thread,13% Cr Trim with Stellite Body Seat (API #8), 13
Cr Stem,Handwheel Operator
V01GLRJ02101 1/2 - 2 800 CS, ASTM A105,Globe Valve,OS&Y,Socket Weld,13% Cr
Trim with Stellite Body Seat (API #8), 13 Cr Stem,Handwheel
Operator
V01XLUJ02101 1/2 - 2 800 CS, ASTM A105,Bellows Seal Globe Valve, OS&Y,Socket V107

Page 552/2074
 September 2019
Revision 3.2

REP Piping Classes

Weld / Female Pipe Thread,13% Cr Trim with Stellite Body

Seat (API #8), 13 Cr Stem,Handwheel Operator
V01XLRJ02101 1/2 - 2 800 CS, ASTM A105,Bellows Seal Globe Valve, OS&Y,Socket V107
Weld,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem,Handwheel Operator

CHECK VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
V01CPRJ02001 1/2 - 2 800 CS, ASTM A105,Check, Horizontal Lift Piston Spring
Assisted,Socket Weld,13% Cr Trim with Stellite Body Seat
(API #8), 13 Cr Stem
V02CS6302001 3 - 24 300 CS, ASTM A216 Grade WCB,Check Valve, Swing V16, V44, V58
Type,ASME B16.5 Flanged (Raised Face), Integral with
Body,13% Cr Trim with Stellite Body Seat (API #8), 13 Cr
Stem
V02CU6302001 3 - 24 300 CS, ASTM A216 Grade WCB,Check Valve, Lug Body, V16, V44, V57
Through Drilled, Dual Disc,Interface with ASME B16.5 Flange
(Raised Face),13% Cr Trim with Stellite Body Seat (API #8),
13 Cr Stem

BALL VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
V02BNR30SF01 1/2 - 2 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V138, V05, V17,
Reduced Port, Floating Ball, Firesafe,Single Reduced V43
Port,Socket Weld,316 SS Ball and Stem w/ Reinforced Teflon
Seat - Soft Seated,Firesafe To API 607 (Seats, gasket and
packing),Oval Handwheel with Integral Latch
V02BN6309F01 1/2 - 2 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V05, V17, V43
Reduced Port, Floating Ball,Single Reduced Port,ASME B16.5
Flanged (Raised Face), Integral with Body,316 SS Ball w/
Stellite Trim or Equal (API #12) - Metal Seated,Inherently
Firesafe (Seats, gasket and packing),Oval Handwheel with
Integral Latch
V02BN630SF01 1/2 - 2 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V138, V05, V17,
Reduced Port, Floating Ball, Firesafe,Single Reduced V43
Port,ASME B16.5 Flanged (Raised Face), Integral with
Body,316 SS Ball and Stem w/ Reinforced Teflon Seat - Soft
Seated,Firesafe To API 607 (Seats, gasket and packing),Oval
Handwheel with Integral Latch
V02BNR309F01 1/2 - 2 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V05, V17, V43
Reduced Port, Floating Ball,Single Reduced Port,Socket
Weld,316 SS Ball w/ Stellite Trim or Equal (API #12) - Metal
Seated,Inherently Firesafe (Seats, gasket and packing),Oval
Handwheel with Integral Latch
VSEBWS30EF01 3/4 - 3/4 300 316 SS, ASTM A182 Grade F316,Ball Valve, 3-Way, Top V18, V43
Entry, Unibody, Floating Ball,Multi Reduced Port,Female Pipe
Thread,316 SS Ball and Stem w/ 316 SS Seat (API #10) -
Metal Seated,Inherently Firesafe (Seats, gasket and
packing),Oval Handwheel with Integral Latch
V02BN630S401 3-4 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V138, V05
Reduced Port, Floating Ball, Firesafe,Single Reduced
Port,ASME B16.5 Flanged (Raised Face), Integral with
Body,316 SS Ball and Stem w/ Reinforced Teflon Seat - Soft
Seated,Firesafe To API 607 (Seats, gasket and
packing),Wrench Operator (removable handle)

Page 553/2074
 September 2019
Revision 3.2

REP Piping Classes

V02BN6309401 3-4 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V05
Reduced Port, Floating Ball,Single Reduced Port,ASME B16.5
Flanged (Raised Face), Integral with Body,316 SS Ball w/
Stellite Trim or Equal (API #12) - Metal Seated,Inherently
Firesafe (Seats, gasket and packing),Wrench Operator
(removable handle)
V02BN630S201 6 - 12 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V138, V05
Reduced Port, Floating Ball, Firesafe,Single Reduced
Port,ASME B16.5 Flanged (Raised Face), Integral with
Body,316 SS Ball and Stem w/ Reinforced Teflon Seat - Soft
Seated,Firesafe To API 607 (Seats, gasket and packing),Gear
Operator
V02BN6309201 6 - 12 300 CS, ASTM A216 Grade WCB,Ball Valve, Top Entry, Unibody, V05
Reduced Port, Floating Ball,Single Reduced Port,ASME B16.5
Flanged (Raised Face), Integral with Body,316 SS Ball w/
Stellite Trim or Equal (API #12) - Metal Seated,Inherently
Firesafe (Seats, gasket and packing),Gear Operator

BUTTERFLY VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
V02BH6309401 3-4 300 CS, ASTM A216 Grade WCB,Butterfly, Lug Type, Through V05, V44, V46
Drilled, Hydrocarbon API 609 Category B, Bidirectional,
Fire-Safe,Interface with ASME B16.5 Flange (Raised
Face),316SS Trim with Stellite Body Seat (API #12), 316
Stem,Wrench Operator (removable handle)
V02BH6309201 6 - 24 300 CS, ASTM A216 Grade WCB,Butterfly, Lug Type, Through V05, V44, V46
Drilled, Hydrocarbon API 609 Category B, Bidirectional,
Fire-Safe,Interface with ASME B16.5 Flange (Raised
Face),316SS Trim with Stellite Body Seat (API #12), 316
Stem,Gear Operator

PlUG VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
V02PC630X401 3-6 300 CS, ASTM A216 Grade WCB,Plug Valve, Block & Bleed Body, V121, V05
Short Pattern per API 599, Short Pattern Port,ASME B16.5
Flanged (Raised Face), Integral with Body,13% Cr Trim with
Viton O-Rings - Soft Seated,Firesafe To API 607 (Seats,
gasket and packing),Wrench Operator (removable handle)
V02PC630X201 8 - 24 300 CS, ASTM A216 Grade WCB,Plug Valve, Block & Bleed Body, V121, V05
Short Pattern per API 599, Short Pattern Port,ASME B16.5
Flanged (Raised Face), Integral with Body,13% Cr Trim with
Viton O-Rings - Soft Seated,Firesafe To API 607 (Seats,
gasket and packing),Gear Operator

NEEDLE VALVES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES

PIPING (BAAA1)
COMPCODE SIZE RATING DESCRIPTION NOTES
0021400200 1/2 - 2 XS PIPE: CS, ASTM A106 Grade B, Seamless, Plain Both Ends,
XS
0021100200 2-2 XS PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends, XS P31
0021100100 3-6 Std Wt PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends,
Std Wt
0021100100 8-8 Std Wt PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends, P13

Page 554/2074
 September 2019
Revision 3.2

REP Piping Classes

Std Wt
0021100100 10 - 12 Std Wt PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends,
Std Wt
0021100200 14 - 14 XS PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends, XS P13
0021100200 16 - 18 XS PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends, XS
0021100-00 20 - 24 Calculate PIPE: CS, ASTM A106 Grade B, Seamless, Beveled Ends, P18
Calculate

PIPING NIPPLES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
4021500D00 1/2 - 2 Sch 160 NIPPLE: CS, ASTM A106 Grade B, Seamless, 3" Long,
Threaded One End, Sch 160
4022500D00 1/2 - 2 Sch 160 NIPPLE: CS, ASTM A106 Grade B, Seamless, 6" Long,
Threaded One End, Sch 160
4022400200 1/2 - 2 XS NIPPLE: CS, ASTM A106 Grade B, Seamless, 6" Long, Plain P14
Both Ends, XS
4021400200 1/2 - 2 XS NIPPLE: CS, ASTM A106 Grade B, Seamless, 3" Long, Plain P14
Both Ends, XS

FITTINGS (BAAA1)
COMPCODE SIZE RATING DESCRIPTION NOTES
301P300000 1/2 - 2 - FITTING: CS, ASTM A105, Plug, Round Head, Threaded F05
301P200000 1/2 - 2 - FITTING: CS, ASTM A105, Plug, Round Head, Socketweld F05
30143M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Cap, Threaded, Class 3000 F05
301B3MSR00 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Thredolet, Threaded, Class 3000, F05, F66
Specify Run Size
30172M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Coupling, Socketweld, Class 3000
30162M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Union (Ground Joint Integral
Seat), Socketweld, Class 3000
30142M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Cap, Socketweld, Class 3000
30132M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Tee, Socketweld, Class 3000
30112M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, 90 Degree Elbow, Socketweld,
Class 3000
30122M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, 45 Degree Elbow, Socketweld,
Class 3000
301A2M0000 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Elbolet, Socketweld, Class 3000
301C2MSR00 1/2 - 2 Class 3000 FITTING: CS, ASTM A105, Sockolet, Socketweld, Class 3000, F66
Specify Run Size
2011100200 2-2 XS FITTING: CS, ASTM A234 Grade WPB, 90 Degree Long P31
Radius Elbow, Buttweld, XS
2012100200 2-2 XS FITTING: CS, ASTM A234 Grade WPB, 45 Degree Long P31
Radius Elbow, Buttweld, XS
2013100200 2-2 XS FITTING: CS, ASTM A234 Grade WPB, Tee, Buttweld, XS P31
2018100200 2-2 XS FITTING: CS, ASTM A234 Grade WPB, Cap, Buttweld, XS P31
201GS00200 1/2 - 2 XS FITTING: CS, ASTM A234 Grade WPB, Concentric Swage, F03
Beveled Large End / Plain Small End, XS
201GS00D00 1/2 - 2 Sch 160 FITTING: CS, ASTM A234 Grade WPB, Concentric Swage, F03
Beveled Large End / Plain Small End, Sch 160
201HS00200 1/2 - 2 XS FITTING: CS, ASTM A234 Grade WPB, Eccentric Swage, F03
Beveled Large End / Plain Small End, XS
201HS00D00 1/2 - 2 Sch 160 FITTING: CS, ASTM A234 Grade WPB, Eccentric Swage, F03

Page 555/2074
 September 2019
Revision 3.2

REP Piping Classes

Beveled Large End / Plain Small End, Sch 160

2011100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, 90 Degree Long
Radius Elbow, Buttweld, Std Wt
2017100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, 90 Degree Short F02
Radius Elbow, Buttweld, Std Wt
2012100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, 45 Degree Long
Radius Elbow, Buttweld, Std Wt
2013100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, Tee, Buttweld, Std Wt
2014100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, Conc Reducer, F03
Buttweld, Std Wt
2015100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, Ecc Reducer, F03
Buttweld, Std Wt
2018100100 3 - 12 Std Wt FITTING: CS, ASTM A234 Grade WPB, Cap, Buttweld, Std Wt
301K50SSB1 3 - 12 Branch Std Wt FITTING: CS, ASTM A105, Weldolet, Buttweld, Specify Run F25, F67
Size and Run Schedule (match Pipe Schedule of Class),
Branch Std Wt
2011100200 14 - 18 XS FITTING: CS, ASTM A234 Grade WPB, 90 Degree Long
Radius Elbow, Buttweld, XS
2012100200 14 - 18 XS FITTING: CS, ASTM A234 Grade WPB, 45 Degree Long
Radius Elbow, Buttweld, XS
2013100200 14 - 18 XS FITTING: CS, ASTM A234 Grade WPB, Tee, Buttweld, XS
2014100200 14 - 18 XS FITTING: CS, ASTM A234 Grade WPB, Conc Reducer, F03
Buttweld, XS
2015100200 14 - 18 XS FITTING: CS, ASTM A234 Grade WPB, Ecc Reducer, F03
Buttweld, XS
2018100200 14 - 18 XS FITTING: CS, ASTM A234 Grade WPB, Cap, Buttweld, XS
301K50SSB2 14 - 18 Branch XS FITTING: CS, ASTM A105, Weldolet, Buttweld, Specify Run F25, F67
Size and Run Schedule (match Pipe Schedule of Class),
Branch XS
2011100-00 20 - 24 Calculate FITTING: CS, ASTM A234 Grade WPB, 90 Degree Long P18
Radius Elbow, Buttweld, Calculate
2012100-00 20 - 24 Calculate FITTING: CS, ASTM A234 Grade WPB, 45 Degree Long P18
Radius Elbow, Buttweld, Calculate
2013100-00 20 - 24 Calculate FITTING: CS, ASTM A234 Grade WPB, Tee, Buttweld, P18
Calculate
2014100-00 20 - 24 Calculate FITTING: CS, ASTM A234 Grade WPB, Conc Reducer, P18, F03
Buttweld, Calculate
2015100-00 20 - 24 Calculate FITTING: CS, ASTM A234 Grade WPB, Ecc Reducer, P18, F03
Buttweld, Calculate
2018100-00 20 - 24 Calculate FITTING: CS, ASTM A234 Grade WPB, Cap, Buttweld, P18
Calculate
301K50SSB- 20 - 24 Branch calculate FITTING: CS, ASTM A105, Weldolet, Buttweld, Specify Run P18, F25, F67
Size and Run Schedule (match Pipe Schedule of Class),
Branch calculate

FLANGES (BAAA1)
COMPCODE SIZE RATING DESCRIPTION NOTES
1015230200 1/2 - 2 300 FLANGES: CS, ASTM A105N (Normalized), Socketweld per FP66
ASME B16.5, Raised Face, Class 300, XS
1011230200 2-2 300 FLANGES: CS, ASTM A105N (Normalized), Welding Neck per P31, FP66
ASME B16.5, Raised Face, Class 300, XS

Page 556/2074
 September 2019
Revision 3.2

REP Piping Classes

1011230100 3 - 12 300 FLANGES: CS, ASTM A105N (Normalized), Welding Neck per FP66
ASME B16.5, Raised Face, Class 300, Std Wt
1011230200 14 - 18 300 FLANGES: CS, ASTM A105N (Normalized), Welding Neck per FP66
ASME B16.5, Raised Face, Class 300, XS
1011230-00 20 - 24 300 FLANGES: CS, ASTM A105N (Normalized), Welding Neck per FP66
ASME B16.5, Raised Face, Class 300, Bore to Match Pipe
1017230000 1 1/2 - 1 1/2 300 FLANGES: CS, ASTM A105N (Normalized), Long Weld Neck, F42, FP66
Raised Face, Class 300
1016230000 1/2 - 24 300 FLANGES: CS, ASTM A105N (Normalized), Blind per ASME FP66
B16.5, Raised Face, Class 300

ORIFICE FLANGES (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
101AH30200 2-2 300 ORIFICE FLANGE: CS, ASTM A105N (Normalized), Orifice F41, FP66
Welding Neck per ASME B16.36, Raised Face with 1/2"
Socketweld Taps, Class 300, XS
101AH30100 3 - 12 300 ORIFICE FLANGE: CS, ASTM A105N (Normalized), Orifice F41, FP66
Welding Neck per ASME B16.36, Raised Face with 1/2"
Socketweld Taps, Class 300, Std Wt
101AH30200 14 - 18 300 ORIFICE FLANGE: CS, ASTM A105N (Normalized), Orifice F41, FP66
Welding Neck per ASME B16.36, Raised Face with 1/2"
Socketweld Taps, Class 300, XS
101AH30-00 20 - 24 300 ORIFICE FLANGE: CS, ASTM A105N (Normalized), Orifice F41, FP66
Welding Neck per ASME B16.36, Raised Face with 1/2"
Socketweld Taps, Class 300, Bore to Match Pipe

GASKETS (BAAA1)
COMPCODE SIZE RATING DESCRIPTION NOTES
7SS4030000 1/2 - 24 300 GASKET: 316L SS with SS Inner & CS Outer Ring & Flexible
Graphite Filler, Spiral Wound, per ASME B16.20 for ASME
B16.5 flange, Class 300

BOLTING (BAAA1)
COMPCODE SIZE RATING DESCRIPTION NOTES
8022000000 1/2 - 24 - BOLTING: ASTM A193 Grade B7 / ASTM A194 Grade 2H, B02, B06
Stud Bolts with 2 hvy hex nuts

BLINDS & SPACERS, LINE BLANKS (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
5051630000 1 - 12 300 BLIND: CS, ASTM A516 Grade 70, Figure 8 Blank, ASME
B16.48, Raised Face, ANSI/ASME B16.5, Class 300
5052630000 14 - 24 300 BLIND: CS, ASTM A516 Grade 70, Paddle Blank, ASME
B16.48, Raised Face, ANSI/ASME B16.5, Class 300
5053630000 14 - 24 300 BLIND: CS, ASTM A516 Grade 70, Paddle Spacer, ASME
B16.48, Raised Face, ANSI/ASME B16.5, Class 300

SPECIALTY COMPONENTS (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES
5014DN0000 1/2 - 2 6000# STRAINER: CS, Y-Type Strainer, 0.033" Perforations,
Socketweld, 6000#

SPECIALTY PIPING (BAAA1)

COMPCODE SIZE RATING DESCRIPTION NOTES

Page 557/2074
 September 2019
Revision 3.2

REP Piping Classes

PIPING INSTRUMENT CONNECTIONS (BAAA1)

The following connections shall be provided for instrumentation use:
Temperature Connection: NPS 1-1/2 Long Weldneck Flanged
Valve @ Press Connection: NPS 3/4 Socketweld / Threaded or NPS 3/4 Male Socketweld / Threaded Extended Body Valve
Valve @ Orifice Flange: NPS 1/2 Male Socketweld / Threaded Extended Body Valve or NPS 1/2 Socketweld / Threaded

EQUIPMENT INSTRUMENT CONNECTIONS (BAAA1)

Vessel and exchanger instrument connections: Std. Instr. Connections - Socketweld Construction per Table 1 of REP 5-6-5

BRANCHES (BAAA1)
HEADER SIZE RANGE BRANCH SIZE RANGE BRANCH CONNECTION TYPE NOTES
1/2 - 24 Full Tee C03
3/4 - 2 1/2 - 1 1/2 Reducing Tee C03
3 - 24 1/2 - 1 1/2 Sockolet/ Elbolet C02,
C03
3 - only 2 only Reducing Tee C03
4 - 24 2 only Sockolet/ Elbolet C02,
C03
6 - 24 3 - 12 if B/H is <= 50% Weldolet C03
4 - 24 3 - 22 if B/H is > 50% Reducing Tee C03

Notes (BAAA1)
B02 Bolt lengths shall be per applicable flange and/or blind specification, i.e., ASME B16.5 / B16.47.
B06 For uninsulated flanges, the bolt temperature may be taken as 80% of the fluid temperature or pipe class design
temperature. With Owner's Engineer Approval, a lower bolt temperature may be used if determined by test or heat
transfer calculations.
C02 Use threadolets for unvalved vents and drains.
C03 Alternative Branch Connection Designs per Table 2 of Practice 5-5-1 may also be used with the Owner's Engineer
Approval.
F02 Use only where long radius elbow cannot be used due to space limitation.
F03 Use swages where small end is NPS 2 and smaller, use weld reducer where small end is NPS 3 and larger.
F05 Use for unvalved vents and drains for hydrostatic test. Plug must be dry threaded and seal welded after hydrostatic test.
F25 Must specify both branch schedule and run schedule in order. If a single stock -olet is provided, its schedule must be
equal to or greater than both the run and branch schedule listed. Concerns for weld deformation of the run pipe shall be
considered.
F41 Any unused pressure tap shall be sealed by socket welding a weldable quality bar stock (Not Free Machining Grade) that
matches the chemistry of the orifice flange. The bar stock shall extend beyond the orifice flange OD by 1.5 to 2 inches.
F42 Long Weld Neck flange used for Temperature Connections only
F66 The Branch size and fitting class are listed for the sockolets and threadolets. The Run size (not shown in description)
must be specified when purchasing to match existing pipe. No run schedule is required for sockolets or threadolets.
F67 The branch size and branch schedule are listed for the Weldolets.? The run size and run schedule must also be listed in
the purchase order but could not be included in the piping class due to the large number of potential combinations.
FP66 On 10/1/16 all 150# and 300# A105 flanges were required to be provided in the normalized condition. Note that flanges
installed prior to this date may not be normalized even though their compcodes are the same.
P13 A smaller pipe schedule is available which meets the design requirements and may be used with Owner's Engineer
approval, see Practice 5-2-3, para. 9.3. Instead, a standard, more readily available schedule is listed here.
P14 Plain End Nipples between a pipe or vessel and the first block valve shall be at least schedule 160 thickness.
P18 When calculating the pipe wall thickness, the corresponding calculated pipe MDMT should be less than or equal to the
MDMT of this class. When this is not attainable, refer to Practice 5-1-1 Paragraph 4.2 for MDMT requirements.
P31 Usage of NPS 2 buttweld fittings, pipe, and flanges requires Owner's Engineer Approval.
V01 Use only against flanged nozzles, removable spools & other flanged connections

Page 558/2074
 September 2019
Revision 3.2

REP Piping Classes

V05 Use only where indicated on drawings.

V06 Use gate valves for sizes NPS 6 and larger. Globe valves may be used for sizes NPS 6 and larger with Owner's
Engineer Approval.
V107 For Los Angeles Refinery ONLY, Bellows Seal Gate and Globe valves are required by local regulations to be used in
light hydrocarbon and certain hazardous services <= NPS 14. Consult the LAR Environmental Department and LAR
Specification SP-140-1.
V121
V138 Maximum temperature for soft seated valves is 450F
V16 Wafer check valves shall not be used downstream of reciprocating compressor and pump. See Practice 5-3-1 for
additional limitations of wafer valves.
V17 Substitution of top entry valves by other types shall require Owner's Engineer approval.
V18 Use for sample connection only.
V25 Use for vents, drains and instrument connections where insulation thickness prohibits the use of extended body valves.
Use also for orifice flange connections.
V32 Valve may be used in lieu of line class specified Socketweld / Female Pipe Thread, or Male Socketweld / Female Pipe
Thread valves only for vents, drains or instrument connections.
V43 Cast steel material may be used in lieu of forged steel material for valve body.
V44 Refer to Practice 5-3-1 for additional limitations of wafer and wafer-lug valves.
V46 If used for dead end service, assure butterfly valve has full pressure class rating in both directions of isolation.
V57 Ferndale Refinery prefers the usage of swing check valves. Usage of dual disc check valves at Ferndale Refinery
requires Owner's Engineer Approval.
V58 Alliance Refinery prefers the usage of dual disc check valves. Usage of swing check valves at Alliance Refinery requires
Owner's Engineer Approval.
V69 An integrally reinforced extended body male butt weld is allowed with Owner's Engineer Approval.
V70 An integrally reinforced extended male design (Lip or Butt Weld) must be fully welded out to the machined bevel per
manufacturer's installation guidelines.
V71 Integrally reinforced extended male lip designs and standard male lip designs are not allowed in crevice corrosion or
stress corrosion cracking services.
V95 Maximum temperature for PEEK seated valves is 600F.

Page 559/2074