Electrodos-Revestidos Kiswell

Covered Electrodes
FOR CARBON STEEL

FOR HIGH TENSILE STRENGTH STEEL
FOR ATMOSPHERIC CORROSION
RESISTING STEEL
FOR LOW TEMPERATURE SERVICE STEEL
FOR HEAT-RESISTING STEEL
FOR HARDFACING
FOR STAINLESS STEEL
FOR CAST IRON
FOR SPECIAL PURPOSE
Covered Electrodes
KCL-10For 420MPa mild steel
Classifications
EN ISO 2560-A:2006 : E 38 0 C 22 KS D 7004 : E4311
EN ISO 2560-B:2006 : E 43 10 A JIS Z 3211 : E4310
AWS A5.1-04 : E6010
Description
Covering is high cellulose type for welding of pipe, shipbuildings, tanks or galvanized surfaces and steel
casting repairs.
Good penetration combined with freedom from lack of fusion makes this electrode an excellent choice
for pipe welding.
Gives high ductility root weld and easy slag removal.
Redry the electrode at 70~80℃ for 30~60 minutes prior to use.
Welding positions
Typical chemical composition of all-weld metal (%)

C Si Mn P S Ni Cr Mo V
0.11 0.36 0.63 0.015 0.013 0.02 0.03 0.01 0.01
Typical mechanical properties of all-weld metal

Y.S T.S El. IV (J)
(MPa) (MPa) (%) 0℃ -30℃ Remarks
AWS A5.1 min. 330 min. 430 min. 22 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 420 500 29 60 40 AW
AW : As-Welded
Sizes available and recommended currents (DC +)

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 350 350
Amp. F 50~80 70~110 110~150 160~200
(A) V·OH 40~70 60~100 90~130 140~170
Approvals
ABS BV GL LR NK
3,E6010 3 3 3m KMW3
Others : JIS, CE
39
Covered Electrodes
KCL-11
For 420MPa mild steel
Classifications
EN ISO 2560-A:2006 : E 38 2 C 12 KS D 7004 : E4311
EN ISO 2560-B:2006 : E 43 10 A JIS Z 3211 : E4311
AWS A5.1-04 : E6011
Description
Covering is high cellulose type for welding of steel sheets, pipes in building or shipbuilding.
As the welding in poor groove fit up and vertical-down welding can be performed easily, it is used in
all position welding of pipes.
Good mechanical properties and the weld metal neets requirement X-ray.
Gives high ductility root weld and easy slag removal.
Welding positions

0.08 0.31 0.58 0.017 0.018 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.1 min. 330 min. 430 min. 22 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 410 500 24 60 40 AW
AW : As-Welded
Sizes available and recommended currents (AC or DC +)

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 350 350
Amp. F 50~80 70~110 110~150 160~200
(A) V·OH 40~70 60~100 90~130 140~170
Approvals
ABS BV GL LR
3,E6011 3 3 3m
Others : JIS, CE
40
Covered Electrodes
K-6012For 420MPa mild steel
Classifications
EN ISO 2560-A:2006 : E 38 0 R 12 KS D 7004 : E4313
EN ISO 2560-B:2006 : E 43 12 A JIS Z 3211 : E4312
AWS A5.1-04 : E6012
Description
Covering is high titania type for welding of shells of railway vehicles, cars and othersteel structures
and general light structural steels.
Good weldability in vertical-down welding.
Excellent X-ray quslity and good bead appearance.
Welding positions

0.07 0.39 0.52 0.020 0.011 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) RT 0℃ Remarks
AWS A5.1 min. 330 min. 430 min. 17 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 400 490 30 60 40 AW
AW : As-Welded
Sizes available and recommended currents (AC or DC -)

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~95 80~120 130~170 180~230 240~300
(A) V·OH 40~95 70~110 100~140 120~160
Approvals
JIS, CE
41
Covered Electrodes
KR-3000
Classifications
EN ISO 2560-A:2006 : E 38 0 R 11 KS D 7004 : E4313
EN ISO 2560-B:2006 : E 43 13 A JIS Z 3211 : E4313
AWS A5.1-04 : E6013
Description
Covering is high titania type for welding of all kinds of light constructional work in all positions,
including pipe welding.
Excellent striking and restriking properties.
Excellent slag removal and bead appearance without undcut.
Welding positions

0.06 0.35 0.40 0.020 0.011 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
AWS A5.1 min. 330 min. 430 min. 17 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 430 490 28 75 60 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~100 80~130 130~180 160~220 210~280
(A) V·OH 60~90 80~110 90~140 120~190
Approvals
ABS BV DNV GL KR LR NK
2 2 2 2 2 2m KMW2
Others : KS, JIS, CE
42
Covered Electrodes
KR-3000V For 420MPa mild steel
Classifications
EN ISO 2560-A:2006 : E 38 0 R 15 KS D 7004 : E4313
EN ISO 2560-B:2006 : E 43 13 A JIS Z 3211 : E4313
AWS A5.1-04 : E6013
Description
60~80°
Welding of shells of railway vehicles, cars and other steel sheet structures and
general light structural steels. 45°
In vertical-down welding, excellent bead appearance can be obtained by taking
a little bit higher welding amperage and holding the electrode at the illustrated angles.
Welding under excessive amperage conditions can cause the deterioration of radiographic soundness.
Welding positions

0.09 0.38 0.49 0.020 0.013 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
AWS A5.1 min. 330 min. 430 min. 17 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 420 490 29 65 50 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp.(A) V-down 80~120 100~150 150~200 210~250
Approvals
ABS BV LR
2 2 2m
43
Covered Electrodes
KI-101LF
Classifications
EN ISO 2560-A:2006 : E 38 2 RA 12 KS D 7004 : E4301
EN ISO 2560-B:2006 : E 43 19 A U JIS Z 3211 : E4319
AWS A5.1-04 : E6019
Description
Covering is ilmenite type for welding of high pressure boilers, ship hulls, building, bridges and other
structural fabrications.
The most excellent mechanical properties and also suitable for welding of structural steels of heavy
section about 25mm thickness.
Welding positions

0.07 0.15 0.47 0.020 0.012 0.01 0.02 0.01 0.01

Y.S T.S El. IV (J)
AWS A5.1 min. 330 min. 430 min. 22 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 400 490 30 100 80 AW
AW : As-Welded
Sizes available and recommended currents (AC or DC +, -)

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 80~135 135~190 180~240 250~310
(A) V·OH 50~75 60~120 100~160 135~210 -
Approvals
3 3 3 3 3 3m KMW3
44
Covered Electrodes
K-6022For 420MPa mild steel
Classifications
EN ISO 2560-A:2006 : E 38 0 A 23
AWS A5.1-04 : E6022
Description
Covering is high iron oxide type for welding of flat and horizontal fillet welding of sheet metal.
Highly efficient welding.
Welding under excessive amperage conditions can cause the deterioration of radiographic soundness.
Welding positions

0.14 0.28 1.20 0.025 0.012 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
AWS A5.1 min. 330 min. 430 min. 17 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 450 480 26 75 55 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F
60~110 80~140 160~200 180~240 260~320
(A) V·OH
Approvals
JIS, CE
45
Covered Electrodes
KF-300LF
Classifications
EN ISO 2560-A:2006 : E 38 0 A 53 KS D 7004 : E4327
EN ISO 2560-B:2006 : E 43 27 A JIS Z 3211 : E4327
AWS A5.1-04 : E6027
Description
Covering is high iron oxide, iron powder type for welding of flat and horizontal fillet welding of ship
hull constructions, bridges and general structures.
Beautiful bead appearance with undercut.
Extremely high efficient welding because of high deposition rate by much iron powder.
Easy slag removal.
Welding positions

0.07 0.47 0.76 0.020 0.014 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
AWS A5.1 min. 330 min. 430 min. 22 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 490 560 28 60 40 AW
AW : As-Welded

Dia. (mm) 4.0 4.5 5.0 5.5 6.0 6.4
Length (mm) 550 550 550 550 550 550
700 700 700 700 700
Amp. F
150~180 180~200 180~230 220~270 250~290 280~310
(A) H-Fillet
Leg (mm) 5.0~5.5 5.5~6.0 6.0~6.5 6.5~7.0 7.0~8.0 7.5~8.5
Approvals
3 3 3 3 3 3m KMW3
46
Covered Electrodes
KT-303 For 420MPa mild steel
Classifications
EN ISO 2560-A:2006 : E 38 0 RB 12 KS D 7004 : E4303
EN ISO 2560-B:2006 : E 43 03 A U JIS Z 3211 : E4303
Description
Covering is lime titania type for welding of cars, other vehicles, light structural steels and pedestrian bridges.
High welding efficiency and restriking property.
Suitable for tack welding and intermittent welding.
Excellent slag removal.
Welding positions

0.06 0.24 0.40 0.017 0.016 0.01 0.02 0.01 0.01

Y.S T.S El. IV (J)
JIS Z 3211 min. 330 min. 430 min. 20 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 420 530 32 100 60 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 65~100 100~140 140~190 200~260 250~330
(A) V·OH 50~90 80~130 110~170 140~210 -
Approvals
ABS DNV GL KR LR NK
3,D4303 3 3 3 3m KMW3
47
Covered Electrodes
KH-500LF
For 490MPa high tensile steel
Classifications
EN ISO 2560-A:2006 : E 38 3 B 12 H10 KS D 7006 : E4316
EN ISO 2560-B:2006 : E 43 16 A U H10 JIS Z 3211 : E4316
AWS A5.1-04 : E7016
Description
Covering is low hydrogen type for welding of strength members of ship hulls and general heavy
structural steels, medium carbon steel, high sulphur steel. Underlaying of hardfacing.
Excellent mechanical properties and radiographic soundness.
Excellent crack resistance even in the welding of difficult to weld steels.
Redry the electrode at 300~400℃ for 1~2 hours prior to use.
Welding positions

C Si Mn* P S Ni* Cr* Mo* V* *Sum
0.07 0.46 0.96 0.015 0.011 0.02 0.03 0.01 0.01 1.03

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
JIS Z 3211 min. 330 min. 430 min. 20 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 460 540 28 120 100 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~240 250~300
(A) V·OH 50~80 80~110 120~160 160~200 -
Approvals
3YH10 3YHH 3YH10 3YH10 3YH15 3YmH15 KMW3H
48
Covered Electrodes
KH-500TFor 490MPa high tensile steel
Classifications
EN ISO 2560-A:2006 : E 38 0 B 12 H10 KS D 7006 : E4316
EN ISO 2560-B:2006 : E 43 16 A H10 JIS Z 3211 : E4316
AWS A5.1-04 : E7016
Description
Covering is low hydrogen type for tack welding of steels of ships, buildings and bridges.
Good arc restriking properties.
Designed for tack welding and intermittent welding.
Easy slag removal.
Welding positions

0.07 0.59 0.86 0.018 0.009 0.02 0.03 0.01 0.01 0.93

Y.S T.S El. IV (J)
JIS Z 3211 min. 330 min. 430 min. 20 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 450 550 29 65 50 AW
AW : As-Welded

Dia. (mm) 2.6 4.0 5.0
Length (mm) 350 400 400
Amp.(A) All 90~150 140~200 190~240
Approvals
KS, JIS, CE
49
Covered Electrodes
KH-500W
Classifications
EN ISO 2560-A:2006 : E 38 0 B 14 H10 KS D 7006 : E4316
EN ISO 2560-B:2006 : E 43 16 A H10 JIS Z 3211 : E4316
AWS A5.1-04 : E7016
Description
Specifically designed for one side welding of pipes and general structures.
Covering is low hydrogen type for welding of all positions except vertical-down.
Extremely good usability in flat positions.
Easy slag removal and beautiful bead appearance.
Welding positions

0.09 0.58 0.98 0.014 0.011 0.02 0.03 0.01 0.01 1.05

Y.S T.S El. IV (J)
JIS Z 3211 min. 330 min. 430 min. 20 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 460 560 32 70 50 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 4.5 5.0
Length (mm) 350 350 400 400 400
Amp.(A) F OSW 30~70 60~110 90~140 120~160 130~180
Approvals
KS, JIS, CE
50
Covered Electrodes
KH-500VLF For 490MPa high tensile steel
Classifications
EN ISO 2560-A:2006 : E 38 0 B 35 H10 KS D 7006 : E4316
EN ISO 2560-B:2006 : E 43 16 A H10 JIS Z 3211 : E4948
AWS A5.1-04 : E7048
Description
Covering is low hydrogen type for vertical-down welding of general structures and
strength members of machinery, ship construction, bridges.
In vertical-down welding, excellent bead appearance can be obtained by taking
60~80°
a little bit higher welding amperage and holding the electrode at the illustrated angles.
Excellent mechanical properties and crack resistance. 45°
Welding positions

0.06 0.53 0.72 0.012 0.011 0.02 0.03 0.01 0.01 0.79

Y.S T.S El. IV (J)
JIS Z 3211 min. 330 min. 430 min. 20 ≥ 27
EN ISO 2560-A min. 380 470~600 min. 20 ≥ 47
Example 460 550 33 70 60 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 4.5 5.0 5.5
Length (mm) 400 450 450 450 450
Amp.(A) V-down 120~160 150~210 180~240 220~280 260~330
Approvals
ABS BV DNV KR LR NK
3YH10 3YHH 3YH10 3YH15 3YmH15 KMW3H
51
Covered Electrodes
K-7014
Classifications
EN ISO 2560-A:2006 : E 42 A RR 32 JIS Z 3211 : E4914
EN ISO 2560-B:2006 : E 49 14 A
AWS A5.1-04 : E7014
Description
Covering is iron powder, titania type for fillet welding of ship structure, bridges, structural steels.
Designed for high efficiency in single pass and multiple pass welding.
Excellent slag removal and good bead appearance.
Quiet and stable arc.
Welding positions

0.08 0.41 0.73 0.020 0.014 0.02 0.03 0.01 0.01 0.80

Y.S T.S El. IV (J)
AWS A5.1 min. 400 min. 490 min. 17 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 470 550 30 65 50 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~100 90~140 140~200 190~240 250~310
(A) V·OH 50~90 80~130 110~170 150~200 -
Approvals
ABS KR LR NK
2Y,E7014 2Y 2Ym KMW52
Others : JIS, CWB, CE
52
Covered Electrodes
K-7024
Classifications
EN ISO 2560-A:2006 : E 42 A RR 53 KS D 7004 : E4324
EN ISO 2560-B:2006 : E 49 24 A JIS Z 3211 : E4924
AWS A5.1-04 : E7024
Description
Covering is iron powder, titania type for flat and horizontal fillet welding of
ship structure, bridges, structural steels for buildings and general structures.
Designed for high efficiency in single pass.
Welding positions

0.08 0.35 0.78 0.020 0.014 0.02 0.03 0.01 0.01 0.85

Y.S T.S El. IV (J)
AWS A5.1 min. 400 min. 490 min. 17 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 480 570 28 65 50 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 4.5 5.0 5.5 6.0
400 450 450 450 450 450
Length (mm) 550 550 550 550 550
700 700 700 700
Amp. F
100~150 140~190 180~230 200~250 230~270 260~300
(A) H-Fillet
Approvals
2Y,E7024 2Y 3 2Y 2Y 2Ym KMW52
53
Covered Electrodes
K-7024N
Classifications
EN ISO 2560-A:2006 : E 42 0 RR 53 KS D 7004 : E4324
EN ISO 2560-B:2006 : E 49 24 A JIS Z 3211 : E4924-1
AWS A5.1-04 : E7024-1
Description
Covering is iron powder, titania type for flat and horizontal fillet welding of ship
structure, bridges, structural steels for buildings and general structures.
Designed for high efficiency in single pass.
Good notch toughness of the deposited weld metal.
Welding positions

0.08 0.63 0.88 0.024 0.020 0.15 0.03 0.01 0.01 1.08

Y.S T.S El. IV (J)
(MPa) (MPa) (%) 0 -20℃ Remarks
AWS A5.1 min. 400 min. 490 min. 17 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 500 590 27 60 40 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 4.5 5.0 5.5 6.0
400 450 450 450 450 450
Length (mm) 550 550 550 550 550
700 700 700 700
Amp. F
100~150 140~190 180~230 200~250 230~270 260~300
(A) H-Fillet
Approvals
JIS, CE
54
Covered Electrodes
K-7010G
Classifications
EN ISO 2560-A:2006 : E 42 0 C 22 JIS Z 3211 : E4910-G
EN ISO 2560-B:2006 : E 49 10-G A
AWS A5.5-06 : E7010-G
Description
Covering is high cellulose type for all positions welding of pipes, general light structural steels.
This electrode is characterized by deeply penetrating, forceful, spray type arc.
Readily removable, thin friable slag.
Welding positions

0.10 0.56 0.87 0.014 0.013 0.34 0.03 0.28 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 390 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 470 570 27 60 40 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 400 400
Amp. F 50~80 70~110 110~150 160~200
(A) V·OH 40~70 60~100 90~130 140~170
Approvals
JIS, CE
55
Covered Electrodes
KK-50LF
Classifications
EN ISO 2560-A:2006 : E 42 3 B 12 H10 KS D 7006 : E5016
AWS A5.1-04 : E7016
Description
Covering is low hydrogen type for welding of 490MPa class high tensile steel in ships, bridges.
Excellent crack resistance even in the welding of difficult to weld steels.
Satisfactory bead appearance and slag removal.
Welding positions

0.07 0.53 0.93 0.013 0.012 0.02 0.03 0.01 0.01 1.00

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.1 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 480 560 32 110 80 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~240 250~310
(A) V·OH 50~80 80~110 120~160 160~200 -
Approvals
56
Covered Electrodes
K-7016HR For 490MPa high tensile steel
Classifications
EN ISO 2560-A:2006 : E 42 3 B 12 H5 KS D 7006 : E5016
EN ISO 2560-B:2006 : E 49 16 A U H5 JIS Z 3211 : E4916 H5
AWS A5.1-04 : E7016 H4R
Description
Covering is low hydrogen type for welding of 490MPa class high tensile steel in ships, bridges.
Good impact properties and very low hydrogen contens. (HD ≤4ml/100g)
Welding positions

0.07 0.57 0.87 0.013 0.011 0.02 0.03 0.01 0.01 0.94

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.1 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 500 610 27 110 90 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~240 250~310
(A) V·OH 50~80 80~110 120~160 160~200
Approvals
3YH5 3YHHH 3YH5 3YH5 3YH5 3YmH5 KMW53H5
Others : JIS, CCS, CE
57
Covered Electrodes
K-7018
Classifications
EN ISO 2560-A:2006 : E 42 3 B 32 H10 KS D 7006 : E5016
AWS A5.1-04 : E7018
Description
Covering is low hydrogen, iron powder type for welding of 490MPa class high tensile steel in ships,
bridges, storage tank, building and industrial machinery.
Welding positions

0.07 0.61 0.87 0.015 0.011 0.02 0.03 0.01 0.01 0.94

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.1 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 480 570 30 100 70 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~100 90~130 130~180 200~250 250~310
(A) V·OH 50~80 80~120 110~170 160~210 -
Approvals
3YH10,E7018 3YHH 3YH10 3YH10 3YH15 3YmH15 KMW53H
Others : KS, JIS, CWB, CE
58
Covered Electrodes
K-7018HR For 490MPa high tensile steel
Classifications
EN ISO 2560-A:2006 : E 42 3 B 32 H5 KS D 7006 : E5016
EN ISO 2560-B:2006 : E 49 18 A U H5 JIS Z 3211 : E4918 H5
AWS A5.1-04 : E7018 H4R
Description
bridges, storage tank, building and industrial machinery.
Good impact properties and very low hydrogen contens. (HD ≤4ml/100g)
Excellent bead appearance and radiographic soundness.
Welding positions

0.07 0.60 0.98 0.015 0.012 0.02 0.03 0.01 0.01 1.05

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.1 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 550 620 29 110 80 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~100 90~130 130~180 200~250 250~310
(A) V·OH 50~80 80~120 110~170 160~210 -
Approvals
3YH5 3YHHH 3YH5 3YH5 3YH5 3YmH5 KMW53H5
Others : JIS, CCS, CE
59
Covered Electrodes
K-7018N
Classifications
EN ISO 2560-A:2006 : E 42 3 B 32 H10 JIS Z 3214 : E4918-1
EN ISO 2560-B:2006 : E 49 18-1 A U H10
AWS A5.1-04 : E7018-1
Description
Covering is low hydrogen, iron powder type for welding of nuclear reactor vessels, LPG tankers, LPG
storage tanks and similar installations at low temperature.
Good impact value at -45℃
Welding positions

0.07 0.58 1.38 0.013 0.012 0.15 0.03 0.01 0.01 1.58

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -45℃ Remarks
AWS A5.1 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 510 590 32 100 75 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 70~100 90~130 150~190 160~220 180~230
(A) V·OH 60~90 85~120 110~160 130~180 -
Approvals
DNV LR
5YH10 5Y40mH15
60
Covered Electrodes
K-7028LF
Classifications
EN ISO 2560-A:2006 : E 42 0 B 52 KS D 7006 : E5026
EN ISO 2560-B:2006 : E 49 28 A JIS Z 3211 : E4928
AWS A5.1-04 : E7028
Description
Covering is low hydrogen type for flat and horizontal fillet welding of 490MPa class high tensile steel.
Extremely high deposition rate and good slag removal.
For application of gravity welding and auto-contact welding.
Welding positions

0.06 0.37 0.98 0.021 0.013 0.02 0.03 0.01 0.01 1.05

Y.S T.S El. IV (J)
AWS A5.1 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 470 550 31 65 50 AW
AW : As-Welded

Dia. (mm) 5.0 5.5 6.0 6.4
550 550 550 550
Length (mm) 700 700 700 700
900 900 900
Amp. F 200~250 270~320 290~340
220~280
(A) H-Fillet
Approvals
Others : JIS, CE
61
Covered Electrodes
K-8010G
Classifications
EN ISO 2560-A:2006 : E 46 0 C 22 JIS Z 3211 : E5510-G
EN ISO 2560-B:2006 : E 55 10-G A
AWS A5.5-06 : E8010-G
Description
Covering is high cellulose type for all positions welding of pipes, general light structural steels.
This electrode is characterized by deeply penetrating, forceful, spray type arc.
Readily removable, thin friable slag.
Welding positions

0.09 0.43 0.76 0.011 0.009 0.32 0.03 0.25 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-A min. 460 530~680 min. 20 ≥ 47
Example 520 610 24 65 50 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 50~80 70~110 110~150 160~200
(A) V·OH 40~70 60~100 90~130 140~170
Approvals
JIS, CE
62
Covered Electrodes
KK-55
Classifications
EN ISO 2560-A:2006 : E 46 3 B 12 H10 KS D 7006 : E5316
EN ISO 2560-B:2006 : E 55 16-G A H10 JIS Z 3211 : E5516-G
AWS A5.5-06 : E8016-G
Description
Covering is low hydrogen type for welding of 560MPa class high tensile steel.
Good weldability and usability.
Welding positions

0.07 0.66 1.45 0.016 0.011 0.02 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -40℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-A min. 460 530~680 min. 20 ≥ 47
Example 540 600 28 60 45 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~240 250~310
(A) V·OH 50~80 80~120 110~170 160~200 -
Approvals
JIS, CE
63
Covered Electrodes
K-8018
Classifications
EN ISO 2560-A:2006 : E 42 3 B 32 H10 KS D 7006 : E5316
EN ISO 2560-B:2006 : E 49 18-G H10 JIS Z 3211 : E5518-G
AWS A5.5-06 : E8018-G
Description
bridges, penstocks and rails.
Welding positions

0.06 0.56 1.32 0.018 0.011 0.35 0.03 0.25 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-A min. 460 530~680 min. 20 ≥ 47
Example 490 590 28 95 80 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~230 250~310
(A) V·OH 50~80 80~110 120~170 160~200 -
Approvals
ABS
3Y
Others : JIS, CE
64
Covered Electrodes
KK-60
Classifications
EN ISO 2560-A:2006 : E 50 0 1Ni B 12 H10 KS D 7006 : E5816
AWS A5.5-06 : E9016-G
Description
Covering is low hydrogen type for welding of 620MPa class high tensile steelin bridges, vehicles.
Mn-Ni-Mo type deposites weld metal.
Welding positions

0.07 0.58 1.04 0.018 0.011 0.64 0.03 0.29 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 530 min. 620 min. 17 ≥ 27
EN ISO 2560-A min. 500 560~720 min. 18 ≥ 47
Example 550 650 28 80 50 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~230 250~300
(A) V·OH 50~80 80~110 120~170 160~200 -
Approvals
JIS, CE
65
Covered Electrodes
KK-70
Classifications
EN 757:1997 : E 55 3 Z B 12 H10 KS D 7006 : E7016
AWS A5.5-06 : E10016-G JIS Z 3211 : E6916-G
Description
Covering is low hydrogen type for welding of 690MPa class high strength low alloy steel, yield point
620MPa of pressure vessels, penstocks and bridges.
Excellent crack resistance and radiographic soundness.
Welding positions

0.07 0.49 1.05 0.015 0.011 1.87 0.05 0.37 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.5 min. 600 min. 690 min. 16 ≥ 27
EN ISO 2560-A min. 550 610~780 min. 18 ≥ 47
Example 640 730 26 100 90 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~230 250~300
(A) V·OH 50~80 80~110 120~170 160~200 -
Approvals
JIS, CE
66
Covered Electrodes
KK-80
Classifications
EN 757:1997 : E 62 0 Z B 12 H10 KS D 7006 : E8016
AWS A5.5-06 : E11016-G JIS Z 3211 : E7616-G
Description
Covering is low hydrogen type for welding of 760MPa class high strength low alloy steel, yield point
690MPa of pressure vessels, penstocks and bridges.
Excellent crack resistance and radiographic soundness.
Welding positions

0.07 0.60 1.10 0.013 0.012 1.84 0.23 0.43 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 670 min. 760 min. 15 ≥ 27
EN ISO 2560-A min. 620 690~890 min. 18 ≥ 47
Example 730 830 22 60 40 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 140~190 180~230 250~300
(A) V·OH 50~80 80~110 120~170 160~200 -
Approvals
JIS, CE
67
Covered Electrodes
K-9018M
Classifications
EN ISO 2560-A:2006 : E 50 5 Z B 32 H10 KS D 7006 : E5816
AWS A5.5-06 : E9018-M JIS Z 3211 : E6218-N3M1
Description
Covering is low hydrogen, iron powder type for welding of 620MPa class high tensile steel in bridge,
pressure vessels, penstocks and machinery.
Excellent mechanical properties especially in notch toughness.
Welding positions

0.05 0.51 0.88 0.013 0.011 1.58 0.10 0.20 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -40℃ -50℃ Remarks
AWS A5.5 540~620 min. 620 min. 24 ≥ 27
EN ISO 2560-A min. 500 560~720 min. 18 ≥ 47
Example 570 670 30 110 90 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~100 90~130 140~190 190~240 250~310
(A) V·OH 40~80 80~115 110~160 140~170 -
Approvals
ABS
E9018M-H8
Others : JIS, CE
68
Covered Electrodes
K-10018M
Classifications
EN 757:1997 : E 55 3 Z B 32 H10 KS D 7006 : E7016
AWS A5.5-06 : E10018-M JIS Z 3211 : E6918-N3M2
Description
Welding positions

0.07 0.46 1.35 0.015 0.012 1.63 0.20 0.28 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -50℃ Remarks
AWS A5.5 610~690 min. 690 min. 16 ≥ 27
EN 757 min. 550 610~780 min. 18 ≥ 47
Example 640 750 29 80 45 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. F 90~130 130~180 180~240 250~320
(A) V·OH 80~115 110~170 140~200 -
Approvals
JIS, CE
69
Covered Electrodes
K-11018M
Classifications
EN 757:1997 : E 62 3 Z B 32 H10 KS D 7006 : E8016
AWS A5.5-06 : E11018-M JIS Z 3211 : E7618-N4M2
Description
Covering is low hydrogen, iron powder type for welding of low alloy high strength steels having tesile
properties of about 740~790MPa such as HY80, etc.
Welding positions

0.08 0.41 1.49 0.015 0.012 1.86 0.25 0.35 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -50℃ Remarks
AWS A5.5 680~760 min. 760 min. 20 ≥ 27
EN 757 min. 620 690~890 min. 18 ≥ 47
Example 730 830 22 80 45 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~100 90~130 130~180 180~240 240~320
(A) V·OH 40~90 80~120 110~160 140~200 -
Approvals
ABS
E11018M-H8
Others : JIS, CE
70
Covered Electrodes
K-12018M For 830MPa high tensile steel
Classifications
EN 757:1997 : E 69 3 Z B 32 H10 JIS Z 3211 : E8618-N4C2M2
AWS A5.5-06 : E12018-M
Description
Good radiographic soundness.
Welding positions

0.08 0.30 1.46 0.014 0.013 1.86 0.95 0.41 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -50℃ Remarks
AWS A5.5 740~830 min. 830 min. 18 ≥ 27
EN 757 min. 690 760~960 min. 17 ≥ 47
Example 800 940 20 70 40 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 70~100 90~130 150~190 180~230 220~300
(A) V·OH 60~90 70~100 120~160 140~180 -
Approvals
JIS, CE
71
Covered Electrodes
K-8018D1
For 560MPa high tensile steel (Mn-Mo steel)
Classifications
EN ISO 2560-B:2006 : E 55 18-3M2 P H5 JIS Z 3211 : E5518-3M2 P H5
AWS A5.5-06 : E8018-D1 H4
Description
Covering is low hydrogen, iron powder type for welding of 560MPa class high tensile steel or
1.5%Mn-0.35%Mo steel.
Very low hydrogen contens. (HD ≤4ml/100g)
Good notch toughness at -50℃.
Welding positions

0.07 0.47 1.33 0.013 0.013 0.77 0.02 0.30 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -40℃ -50℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-B min. 460 min. 550 min. 17 ≥ 27
Example 640 690 25 60 40 PWHT
PWHT : 620℃x1Hr

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. F 70~100 90~150 150~190 190~260
(A) V·OH 60~90 80~130 120~170 140~200
Approvals
JIS, CE
72
Covered Electrodes
K-10018D2
Classifications
EN 757:1997 : E 55 3 Z B T 32 H5 JIS Z 3211 : E6918-4M2 P H5
AWS A5.5-06 : E10018-D2 H4
Description
Covering is low hydrogen, iron powder type for welding of 560MPa class high tensile steel
(ASTM A302 Gr.B) or 1.85%Mn-0.35%Mo steel.
Welding positions

0.10 0.58 1.71 0.017 0.015 0.74 0.02 0.31 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -50℃ Remarks
AWS A5.5 min. 600 min. 690 min. 16 ≥ 27
EN 757 min. 550 610~780 min. 18 ≥ 47
Example 680 760 23 60 40 PWHT
PWHT : 620℃x1Hr

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. F 70~100 90~150 150~190 190~260
(A) V·OH 60~90 80~130 120~170 140~200
Approvals
JIS, CE
73
Covered Electrodes
K-8018D3
Classifications
EN ISO 2560-B:2006 : E 55 18-3M3 P H5 JIS Z 3211 : E5518-3M3 P H5
AWS A5.5-06 : E8018-D3 H4
Description
Covering is low hydrogen, iron powder type for welding of 560MPa class high tensile steel or
1.5%Mn-0.5%Mo steel.
Good notch toughness at -50℃.
Welding positions

0.05 0.37 1.39 0.014 0.010 0.77 0.05 0.55 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -40℃ -50℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 660 730 23 55 35 PWHT
PWHT : 620℃x1Hr

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. F 70~100 90~150 150~190 190~260
(A) V·OH 60~90 80~130 120~170 140~200
Approvals
JIS
74
Covered Electrodes
KW-50G
For atomospheric corrosion resisting steel
Classifications
EN ISO 2560-A:2006 : E 42 3 Z B 12 H10 KS D 7101 : DA5016W
EN ISO 2560-B:2006 : E 49 16-G A H10 JIS Z 3214 : DA5016W
AWS A5.5-06 : E7016-G
Description
Covering is low hydrogen type for welding of 490MPa class high tensile strength weathering type
structural steel for vehicles, building and bridges.
Excellent weather-proof property and crack resistance.
Welding positions

C Si Mn P S Ni Cr Mo V Cu
0.06 0.46 0.74 0.018 0.009 0.63 0.52 0.01 0.01 0.40

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.5 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 27
Example 450 610 28 70 50 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. F 90~130 150~190 180~230 240~280
(A) V·OH 70~110 120~160 130~170 -
Approvals
CE
75
Covered Electrodes
KW-50V
Classifications
AWS A5.5-06 : E7016-G
KS D 7101 : DA5016G
JIS Z 3214 : DA5016G
Description
Covering is low hydrogen type for vertical-down welding of 490MPa class high tensile strength
weathering type structural steel for vehicles, building and bridges.
Excellent working efficieny in vertical-down welding.
Welding positions

C Si Mn P S Ni Cr Mo V Cu
0.06 0.54 0.86 0.015 0.011 0.60 0.51 0.01 0.01 0.27

Y.S T.S El. IV (J)
AWS A5.5 min. 400 min. 490 min. 22 ≥ 27
JIS Z 3214 min. 390 min. 490 min. 23 ≥ 47
Example 440 540 32 100 50 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) V-down 120~160 170~210 220~280
76
Covered Electrodes
KW-50WH
Classifications
KS D 7101 : DA5026W
JIS Z 3214 : DA5026W
Description
Covering is low hydrogen, iron powder type for flat and horizontal fillet welding of 490MPa class high
tensile strength weathering type structural steel for buildings, bridges and other steel structures.
Extremely high deposition rate and easy slag removal.
Welding positions

C Si Mn P S Ni Cr Mo Cu
0.07 0.30 0.92 0.015 0.012 0.53 0.51 0.01 0.39

Y.S T.S El. IV (J)
JIS Z 3214 min. 390 min. 490 min. 23 ≥ 47
Example 510 560 27 65 40 AW
AW : As-Welded

Dia. (mm) 4.0 5.0 5.5 6.0
400 450 450 450
Length (mm) 500 500 500
550 550 550
Amp. F 160~200 200~250 220~270 250~300
(A) H-fillet
77
Covered Electrodes
KW-60G
Classifications
EN ISO 2560-A:2006 : E 50 0 Z B 12 KS D 7101 : DA5816W
EN ISO 2560-B:2006 : E 55 16-G A JIS Z 3214 : DA5816W
AWS A5.5-06 : E8016-G
Description
Covering is low hydrogen type for welding of 560MPa class high tensile strength weathering type
structural steel for buildings, bridges and other steel structures.
Welding positions

0.07 0.65 0.75 0.016 0.011 0.62 0.53 0.01 0.50

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-A min. 500 560~720 min. 18 ≥ 47
Example 530 590 24 100 70 AW
AW : As-Welded

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. F 90~130 150~190 180~230 240~280
(A) V·OH 70~110 120~160 130~170 -
Approvals
CE
78
Covered Electrodes
K-8018W
Classifications
EN ISO 2560-A:2006 : E 46 2 Z B 32 H10
EN ISO 2560-B:2006 : E 55 18-NCC1 A U H10
AWS A5.5-06 : E8018-W2
Description
Covering is low hydrogen, iron powder type for welding of 560MPa class high tensile strength
weathering type structural steel for buildings, bridges and other steel structures.
(ASTM A67 Gr.1 ; A242 Gr.all ; A588 Gr.all ; A606 Gr.all ; A709 Gr.70W)
Excellent weather-proof properties and crack resistance of the deposited weld metal.
Welding positions

0.05 0.47 0.70 0.015 0.015 0.69 0.54 0.01 0.45

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -20℃ -30℃ Remarks
AWS A5.5 min. 460 min. 550 min. 20 ≥ 27
EN ISO 2560-A min. 460 530~680 min. 20 ≥ 47
Example 530 590 24 80 60 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 70~110 90~130 150~190 180~230
(A) V·OH 60~90 70~110 120~160 130~170
Approvals
CE
79
Covered Electrodes
KK-50N
For low temperature service steel (490MPa)
Classifications
EN ISO 2560-A:2006 : E 42 3 Z B 12 H10 KS D 7101 : DL5016-4A0
AWS A5.5-06 : E7016-G
Description
Covering is low hydrogen type for welding of aluminium-killed steel to be used for LPG tankers, LPG
storage tanks, machineries and structures.
Excellent notch toughness of deposited weld metal at low temperature.
Welding positions

0.08 0.42 1.35 0.014 0.011 0.47 0.02 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -45℃ Remarks
AWS A5.5 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 490 570 30 130 90 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~100 70~130 150~190 220~250 250~310
(A) V·OH 30~80 70~100 120~160 150~200 -
Approvals
DNV LR
5YH10 5Y40mH15
Others : CE
80
Covered Electrodes
KK-50NN
Classifications
EN ISO 2560-A:2006 : E 42 5 Z B 12 H10 KS D 7101 : DL5016-6A1
AWS A5.1-04 : E7016-G
Description
Covering is low hydrogen type for welding of aluminium-killed steel to be used for LPG tankers, and
LPG storage tanks, etc.
Excellent notch toughness of deposited weld metal at low temperature.
Welding positions

0.07 0.37 1.45 0.013 0.010 1.37 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -50℃ -60℃ Remarks
AWS A5.5 min. 400 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 27
Example 520 590 28 120 100 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~100 70~130 150~190 220~250 250~300
(A) V·OH 30~80 70~100 120~160 130~200 -
Approvals
CE
81
Covered Electrodes
K-8016C1
Classifications
EN ISO 2560-A:2006 : E 46 6 2Ni B 12 H10 KS D 7023 : DL5016-6P2
EN ISO 2560-B:2006 : E 55 16-N5 P U H10 JIS Z 3211 : E5516-N5 P U
AWS A5.5-06 : E8016-C1
Description
Covering is low hydrogen type for welding of 2.5%Ni steel and aluminium-killed steel used at low
temperature, LPG tanks, etc.
Excellent impact value at -60℃
Welding positions

0.07 0.45 0.98 0.016 0.013 2.25 0.03 0.02 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -50℃ -60℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-B min. 460 500~550 min. 17 ≥ 47
Example 520 600 30 140 120 AW
PWHT : 605℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 110~150 150~190 200~240 250~310
(A) V·OH 50~80 100~140 120~170 150~200 -
Approvals
CE
82
Covered Electrodes
K-8018C1
Classifications
EN ISO 2560-A:2006 : E 46 6 2Ni B 32 H10 JIS Z 3211 : E5518-N5 P U
EN ISO 2560-B:2006 : E 55 18-N5 P U H10
AWS A5.5-06 : E8018-C1
Description
Covering is low hydrogen, iron powder type for welding of 2.5%Ni steel and aluminium-killed steel
used at low temperature, LPG tanks, etc.
Stable arc in flat and horizontal fillet welding.
Weld metal of fine ripple mark without undercut can be obtained.
Welding positions

0.06 0.60 0.96 0.015 0.012 2.41 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -50℃ -60℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-B min. 460 500~550 min. 17 ≥ 47
Example 500 600 32 120 100 PWHT
PWHT : 605℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~100 90~130 130~190 190~250 250~300
(A) V·OH 60~90 85~120 110~160 - -
Approvals
ABS DNV LR
3YH10,E8018-C1 3YH15 3YmH15
Others : CE
83
Covered Electrodes
K-8016C2
Classifications
EN ISO 2560-A:2006 : E 46 6 3Ni B 12 H10 KS D 7023 : DL5016-6P3
EN ISO 2560-B:2006 : E 55 16-N7 P H10 JIS Z 3211 : E5516-N7 P
AWS A5.5-06 : E8016-C2
Description
Covering is low hydrogen type for welding of 3.5%Ni steel and aluminium-killed steel used at low
temperature, LPG tanks, etc.
Excellent impact value at -75℃
Welding positions

0.07 0.45 1.10 0.014 0.011 3.46 0.04 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -60℃ -75℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-B min. 460 500~550 min. 17 ≥ 27
Example 500 610 30 70 55 PWHT
PWHT : 605℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~90 90~130 130~180 180~240 220~260
(A) V·OH 50~80 80~120 110~160 150~200 -
Approvals
CE
84
Covered Electrodes
K-8018C2
Classifications
EN ISO 2560-A:2006 : E 46 6 3Ni B 32 H10 JIS Z 3211 : E5518-N7 P
EN ISO 2560-B:2006 : E 55 18-N7 P H10
AWS A5.5-06 : E8018-C2
Description
Fast, efficient metal transfer in all positions.
Excellent notch toughness of the deposited weld metal at low temperature.
Welding positions

0.07 0.32 1.12 0.013 0.012 3.45 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -60℃ -75℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
EN ISO 2560-B min. 460 500~550 min. 17 ≥ 27
Example 530 620 28 55 40 PWHT
PWHT : 605℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 90~130 135~180 190~240 250~310
(A) V·OH 50~80 80~120 110~170 - -
85
Covered Electrodes
K-8018C3
Classifications
EN ISO 2560-A:2006 : E 46 6 3Ni B 32 H10 JIS Z 3211 : E5518-N2 U
EN ISO 2560-B:2006 : E 55 18-N2 A U H10
AWS A5.5-06 : E8018-C3
Description
Covering is low hydrogen, iron powder type for welding of 1%Ni steel and high tensile strength steel
for military and commercial applications where good impact property.
Fast, efficient metal transfer in all positions.
Excellent deposited weld metal with both AC and DC power source.
Welding positions

0.07 0.45 0.91 0.013 0.012 1.03 0.02 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -40℃ Remarks
AWS A5.5 470~550 min. 550 min. 24 ≥ 27
EN ISO 2560-B min. 460 530~680 min. 20 ≥ 47
Example 530 600 28 100 60 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 60~95 90~130 135~180 190~240
(A) V·OH 60~90 80~120 110~170 -
Approvals
ABS LR
3YH10,E8018-C3 3YmH15
Others : CE
86
Covered Electrodes
K-7018C3L
Classifications
EN ISO 2560-A:2006 : E 42 3 1Ni B 32 H5 JIS Z 3211 : E4918-N2 H5
EN ISO 2560-B:2006 : E 49 18-N2 A H5
AWS A5.5-06 : E7018-C3L H4R
Description
Covering is low hydrogen, iron powder type for welding of 1%Ni steel and aluminium-killed steel used
at low temperature, LPG tanks, etc.
Fast, efficient metal transfer in all positions and very low hydrogen contens. (HD ≤4ml/100g)
Welding positions

0.05 0.31 0.86 0.016 0.016 1.01 0.05 0.02 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -50℃ Remarks
AWS A5.5 min. 390 min. 490 min. 22 ≥ 27
EN ISO 2560-A min. 420 500~640 min. 20 ≥ 47
Example 530 620 34 90 50 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 60~90 90~140 150~190 180~230
(A) V·OH 50~80 80~120 120~160 -
Approvals
CE
87
Covered Electrodes
K-8016C4
Classifications
EN ISO 2560-A:2006 : E 46 5 Z B 12 H5 JIS Z 3211 : E5516-N3 U H5
EN ISO 2560-B:2006 : E 55 16-N3 A U H5
AWS A5.5-06 : E8016-C4 H4
Description
Good weldability and usability and very low hydrogen contens. (HD ≤4ml/100g)
Welding positions

0.06 0.56 0.85 0.013 0.011 1.26 0.03 0.01 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) -30℃ -50℃ Remarks
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27

EN ISO 2560-A min. 460 530~680 min. 20 ≥ 47
Example 530 600 28 110 70 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 60~90 90~140 150~190 180~230
(A) V·OH 50~80 80~120 120~160 -
Approvals
CE
88
Covered Electrodes
K-7010A1
For heat-resisting steel (0.5%Mo)
Classifications
EN ISO 3580-B:2008 : E 49 10-1M3
AWS A5.5-06 : E7010-A1
Description
Covering is high cellulose type for all positions welding of 0.5%Mo steel pipes used for high pressure,
high temperature steam service, structural steel and plates or castings.
Extremely good radiographic soundness and mechanical properties.
Not to use the currents exceeding the recommended currents.
Welding positions

0.09 0.14 0.43 0.015 0.009 0.05 0.06 0.58 0.01

Y.S T.S El. IV (J)
(MPa) (MPa) (%) 20℃ 0℃ Remarks
AWS A5.5 min. 390 min. 490 min. 22 ≥ 27
Example 440 550 29 60 50 PWHT
PWHT : 620℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 350 350
Amp. F 50~75 70~110 110~150 160~200
(A) V·OH 30~70 60~100 90~130 130~170
Approvals
ABS
3Y,E7010-A1
Others : CE
89
Covered Electrodes
K-7016A1
Classifications
EN ISO 3580-A:2008 : E Mo B 12 H10 KS D 7022 : DT1216
EN ISO 3580-B:2008 : E 49 16-1M3 H10 JIS Z 3223 : DT1216
AWS A5.5-06 : E7016-A1
Description
Covering is low hydrogen type for welding of alloys used for hign temperature service such as C-Mo
steel pipes(STPA 12, A335-P1), boiler and heat exchanger steel tubes, rolled steel and cast steel.
Preheat at 100~200℃ and postheat treat at 620~680℃
Welding positions

0.07 0.54 0.83 0.015 0.009 0.02 0.03 0.52 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 390 min. 490 min. 22 ≥ 27
EN ISO 3580-A min. 355 min. 510 min. 22 ≥ 47
Example 560 650 31 60 50 PWHT
PWHT : 620℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 55~85 90~130 140~190 180~250 240~300
(A) V·OH 50~80 80~120 110~170 130~200 -
Approvals
CE
90
Covered Electrodes
K-7018A1
Classifications
EN ISO 3580-A:2008 : E Mo B 32 H10
EN ISO 3580-B:2008 : E 49 18-1M3 H10
AWS A5.5-06 : E7018-A1
Description
Covering is low hydrogen, iron powder type for welding of alloys steel of 490MPa minimum yield point
0.5%Mo steel of pressure pipe, casting and general fabrication of pressure vessel.
High deposition rate in all positions.
Welding positions

0.06 0.49 0.72 0.015 0.011 0.02 0.03 0.53 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 390 min. 490 min. 22 ≥ 27
Example 590 680 28 130 110 PWHT
PWHT : 620℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 80~120 130~180 190~240 240~300
(A) V·OH 50~80 70~110 100~160 - -
Approvals
CE
91
Covered Electrodes
K-8016B1
For heat-resisting steel (0.5%Cr-0.5%Mo)
Classifications
EN ISO 3580-A:2008 : E CrMo0.5 B 12 H10
EN ISO 3580-B:2008 : E 55 16-CM H10
AWS A5.5-06 : E8016-B1
Description
Covering is low hydrogen type for welding of 0.5%Cr-0.5%Mo steel used high temperature high
pressure boilers, chemical equipment and oil refining plants.(A335-P2, A213-T2)
Excellent crack resistance because of low hydrogen contents.
Welding positions

0.07 0.51 0.81 0.014 0.010 0.02 0.51 0.49 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 590 670 26 70 50 PWHT
PWHT : 690℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~85 90~130 130~180 190~240 250~320
(A) V·OH 40~80 80~120 100~160 130~200 -
Approvals
CE
92
Covered Electrodes
K-8016B2
Classifications
EN ISO 3580-A:2008 : E CrMo1 B 12 H10 KS D 7022 : DT2316
EN ISO 3580-B:2008 : E 55 16-1CM H10 JIS Z 3223 : DT2316
AWS A5.5-06 : E8016-B2
Description
Covering is low hydrogen type for welding of 1.25%Cr-0.5%Mo steel used for super-heater tubes, steam
pipes, heaters of boilers for thermoelectric power plant and equipments oil refining industries.
Welding positions

0.06 0.47 0.65 0.014 0.012 0.03 1.31 0.52 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 570 650 26 80 60 PWHT
PWHT : 690℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 80~120 130~180 180~230 240~300
(A) V·OH 50~80 75~110 100~160 - -
Approvals
CE
93
Covered Electrodes
K-8018B2
Classifications
AWS A5.5-06 : E8018-B2
Description
Covering is low hydrogen, iron powder type for welding of 1.25%Cr-0.5%Mo steel used for steam pipes
of boilers, oil refining industries, pressure vessels for high temperature service.
Welding positions

0.06 0.61 0.70 0.014 0.011 0.02 1.32 0.55 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 590 670 25 80 65 PWHT
PWHT : 690℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 65~95 90~130 130~190 190~250 250~300
(A) V·OH 60~90 80~120 110~170 - -
Approvals
ABS DNV LR
3YH10, E8018-B2 3YH10 3YmH15
Others : CE
94
Covered Electrodes
K-9016B3
For heat-resisting steel (2.25%Cr-1%Mo)
Classifications
AWS A5.5-06 : E9016-B3
Description
Covering is low hydrogen type for welding of 2.25%Cr-1%Mo steel used for super-heater tubes, steam
pipes, heaters of boilers for thermoelectric power plant and equipments oil refining industries.
Welding positions

0.08 0.45 0.78 0.016 0.011 0.03 2.37 1.03 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 530 min. 620 min. 17 ≥ 27
Example 620 710 24 55 40 PWHT
PWHT : 690℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 60~100 90~130 130~190 190~240
(A) V·OH 60~90 75~115 110~170 -
Approvals
CE
95
Covered Electrodes
K-9018B3
For heat-resisting steel (2.25%Cr-1%Mo)
Classifications
AWS A5.5-06 : E9016-B3
Description
Covering is low hydrogen, iron powder type for all positions welding of 2.25%Cr-1%Mo steel used for
steam pipe of boilers, oil refining industries, pressure vessels for high temperature service.
Welding positions

0.08 0.50 0.77 0.018 0.011 0.03 2.25 1.02 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 530 min. 620 min. 17 ≥ 27
Example 680 750 21 50 35 PWHT
PWHT : 690℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 60~100 90~130 140~190 190~250
(A) V·OH 60~90 80~120 110~170 -
Approvals
CE
96
Covered Electrodes
K-8015B6
For heat-resisting steel (5%Cr-0.5%Mo)
Classifications
AWS A5.5-06 : E8015-B6
Description
Covering is low hydrogen type for welding of 5%Cr-0.5%Mo steel used in oil refining and chemical
industries, heat treated high tensile strength steel for aircraft part such as SAE 4130.
Welding positions

0.08 0.35 0.84 0.017 0.012 0.04 5.25 0.55 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 670 720 23 60 50 PWHT
PWHT : 740℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 50~90 75~115 120~160 160~210 210~260
(A) V·OH 50~80 70~110 90~130
Approvals
CE
97
Covered Electrodes
K-8016B6
For heat-resisting steel (5%Cr-0.5%Mo)
Classifications
AWS A5.5-06 : E8016-B6
Description
Covering is low hydrogen type for welding of 5%Cr-0.5%Mo steel used in oil refining and chemical
industries, heat treated high tensile strength steel for aircraft part such as SAE 4130.
Welding positions

0.06 0.43 0.57 0.018 0.012 0.04 4.98 0.51 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 680 740 22 55 45 PWHT
PWHT : 740℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 5.0
Length (mm) 350 350 400 400 400
Amp. F 50~90 80~120 120~160 160~210 210~260
(A) V·OH 50~80 70~110 90~130 - -
Approvals
CE
98
Covered Electrodes
K-8015B8
For heat-resisting steel (9%Cr-1%Mo)
Classifications
EN ISO 3580-B:2008 : E 62 15-9C1M H10 KS D 7022 : DT2616
AWS A5.5-06 : E8015-B8 JIS Z 3223 : DT2616
Description
Covering is low hydrogen type for welding of super-heater tubes of high temperature and high
pressure boilers, heater tubes of oil refining equipments.
Preheat at 250~350℃ and postheat treat at 750~850℃ because of high self-hardening property of the
deposited weld metal.
Welding positions

0.08 0.45 0.88 0.018 0.011 0.03 8.86 0.95 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 670 760 22 45 40 PWHT
PWHT : 740℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 60~90 80~120 120~160 160~220 210~260
(A) V·OH 50~60 70~110 90~150
Approvals
CE
99
Covered Electrodes
K-8016B8
For heat-resisting steel (9%Cr-1%Mo)
Classifications
EN ISO 3580-B:2008 : E 62 16-9C1MH10 KS D 7022 : DT2616
AWS A5.5-06 : E8016-B8 JIS Z 3223 : DT2616
Description
Covering is low hydrogen type for welding of super-heater tubes of high temperature and high
pressure boilers, heater tubes of oil refining equipments.
Welding positions

0.08 0.74 0.98 0.020 0.013 0.03 8.48 0.90 0.01

Y.S T.S El. IV (J)
AWS A5.5 min. 460 min. 550 min. 19 ≥ 27
Example 690 780 21 50 45 PWHT
PWHT : 740℃x1Hr

Dia. (mm) 2.6 3.2 4.0 5.0 6.0
Length (mm) 350 350 400 400 450
Amp. F 55~90 80~120 120~160 160~220 210~260
(A) V·OH 50~80 70~110 90~150 - -
Approvals
CE
100
Covered Electrodes
KM-100For hardfacing (Hv 250)
Classifications
EN 14700:2005 : E Fe 1
KS D 7035 : DF2A-250-R
JIS Z 3251 : DF2A-250-R
Description
Covering is high titania type for hardfacing of shafts, tires, gears, crane wheels, etc.
Easy slag removal.
Beautiful, smooth bead appearaqnce.
Extremely machinable the deposited weld metal.
Preheat at 150~200℃ only for low alloy steel and high carbon steel.
Welding positions

C Si Mn P S Ni Cr Mo W
0.11 0.42 0.98 0.016 0.013 0.02 0.03 0.01 0.01

As welded
Conditions
Continuous surfacing nterpass temperature max.100℃
HV 225~240 245~265
HRC 16~20 21~25
HS 33~34 35~38

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 80~120 140~170 170~210 200~250
101
Covered Electrodes
KM-250
For hardfacing (Hv 250)
Classifications
EN 14700:2005 : E Fe 1
KS D 7035 : DF2A-250-B
JIS Z 3251 : DF2A-250-B
Description
Covering is low hydrogen type for hardfacing and repairing of worn parts such as shafts, gears, wheels, etc.
Stable arc, smooth bead appearance and easy slag removal.
High abrasion resistance and impact resistance.
Good machinable the deposited weld metal.
Preheat at 150~200℃ only for multilayer welding of low alloy steell and high carbon steel.
Welding positions

0.18 0.69 2.28 0.013 0.009 0.02 0.03 0.01 0.01

Conditions As welded Heat treated
Interpass temp. 150℃ 900℃ oil quenching 650℃ stress relief
HV 278 395 250
HRC 26.8 40.3 22.2
HS 39 54 36

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 90~130 140~180 180~240 220~300
102
Covered Electrodes
KM-300R For hardfacing (Hv 300)
Classifications
KS D 7035 : DF2A-300-R
JIS Z 3251 : DF2A-300-R
Description
Covering is high titania type for hardfacing of shaft, roller, spindle, crane wheel, etc.
Excellent slag removal and smooth bead appearance.
Preheat at 150℃ only for multilayer welding of low alloy steell and high carbon steel.
Welding positions

0.20 0.28 0.30 0.025 0.022 0.03 2.40 0.01 0.01

HV 308 420 285
HRC 30.8 42.7 27.8
HS 43 57 41

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 80~130 140~180 170~240 240~300
103
Covered Electrodes
KM-300
Classifications
EN 14700:2005 : E Fe 1
KS D 7035 : DF2A-300-B
JIS Z 3251 : DF2A-300-B
Description
Covering is low hydrogen type for hardfacing of shafts, roller, spindle, crane wheel, etc.
Good usability.
High abrasion resistance and impact resistance.
Preheat at 150℃ only for multilayer welding of low alloy steell and high carbon steel.
Welding positions

0.20 0.60 1.48 0.018 0.011 0.02 0.70 0.01 0.01

HV 308 408 280
HRC 30.8 41.6 27.1
HS 43 56 40

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 80~130 140~180 170~240 240~300
104
Covered Electrodes
KM-100C For hardfacing (Hv 350)
Classifications
EN 14700:2005 : E Fe 1
KS D 7035 : DF2A-350-R
JIS Z 3251 : DF2A-350-R
Description
Covering is high titania type for hardfacing of shaft and clutch lugs, etc.
Easy slag removal and smooth bead appearance.
Extremely machinable the deposited weld metal.
Preheat at 150℃ and over only for cast steel, low alloy steell and high carbon steel.
Welding positions

0.19 0.44 0.74 0.015 0.011 0.02 2.60 0.01 0.01

HV 350 435 300
HRC 35.5 44.1 29.8
HS 48 59 42

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 90~120 140~170 190~230 220~280
105
Covered Electrodes
KM-350
Classifications
KS D 7035 : DF2B-350-B
JIS Z 3251 : DF2B-350-B
Description
Covering is low hydrogen type for hardfacing of fans, upper rollers, shafts and sprockets.
Machining is possible in general.
Hardness increases by quenching after machining.
Suitable for intermetallic abrasion and moderate impact abrasion.
Welding positions

0.36 0.65 0.74 0.014 0.011 0.02 2.00 0.01 0.01

HV 358 440 300
HRC 36.1 44.5 29.8
HS 49 59 42

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 90~130 140~180 190~240 220~300
106
Covered Electrodes
KM-500 For hardfacing (Hv 450)
Classifications
KS D 7035 : DF2B-450-B
JIS Z 3251 : DF2B-450-B
Description
Covering is low hydrogen type for hardfacing of idlers, rollers, bulldozer blades, sprockets, caterpillar
links, crushers, dipper teeth and conveyors, etc.
The deposited weld metal has typical martensite structure and high grade of hardness and ductility as welded.
Machining is impossible as welded.
Preheat at 150℃ and over in general.
Welding positions

0.38 0.84 1.56 0.014 0.011 0.02 2.52 0.03 0.01

Conditions As welded Heat treated (furnace coding)
Interpass temp. 150℃ Interpass temp. 300℃ 550℃x6Hr. 625℃x6Hr.
HV 452 408 443 348
HRC 45.5 41.6 44.8 35.8
HS 60 56 59 48

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 80~120 130~170 170~230 220~280
107
Covered Electrodes
KM-700
Classifications
KS D 7035 : DF2B-700-B
JIS Z 3251 : DF2B-700-B
Description
Covering is low hydrogen type for hardfacing of cutter knives, dredger and mixer.
The deposited weld metal has martensite structure.
In the case of multilayer build-up welding base plates of hardening properties, under-laying with low
hydrogen type carbon steel electrode.
Preheat at 150℃ and over in general.
Welding positions

0.48 1.42 1.36 0.015 0.012 0.03 3.65 0.02 0.01

Interpass temp. 200℃ Interpass temp. 300℃ 600℃ stress relief
HV 688 690 585
HRC 59.6 59.7 54.4
HS 81 81 73

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 90~130 140~170 190~240 220~300
108
Covered Electrodes
KSB-2
For hardfacing (High Cr, Hv 600)
Classifications
KS D 7035 : DF3B-600-BR
JIS Z 3251 : DF3B-600-BR
Description
Covering is lime titania type for hardfacing of dies, clutch cams and metal mould.
Excellent working efficiency.
Excellent slag removal and restriking properties.
Excellent heat-resisting, crack-resisting, wear-resisting and impact-resisting properties.
In the case of multilayer build-up welding base plates of hardening properties, under-laying with low
hydrogen type carbon steel electrode.
Welding positions

C Si Mn P S Ni Cr V W
0.50 0.09 0.52 0.021 0.012 0.04 6.1 0.4 1.8

As welded
Conditions Interpass temp. Preheating 200℃,
Continuous surfacing max.100℃ Continuous surfacing
HV 570 650 580
HRC 53.6 57.8 54.1
HS 71 78 72

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 80~100 120~150 160~200
109
Covered Electrodes
KM-800
Classifications
KS D 7035 : DF3C-700-B
JIS Z 3251 : DF3C-700-B
Description
Covering is low hydrogen type for hardfacing of impellers, pump casings.
The deposited weld metal has an extremely hard martensite structure.
Machining is impossible as welded.
Preheat at 200℃ and over.
Postheat treat at about 600℃ immediately after welding.
Welding positions

0.47 1.45 1.51 0.017 0.012 0.03 4.10 0.02 0.01

Interpass temp. 150℃ Interpass temp. 200℃ 600℃ stress relief
HV 723 810 535
HRC 61.1 64.4 51.4
HS 83 89 69

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 90~130 140~170 190~240 220~300
110
Covered Electrodes
KM-11Cr
For hardfacing (Hign Cr, Hv 500)
Classifications
KS D 7035 : DF4B-500-B
JIS Z 3251 : DF4B-500-B
Description
Covering is low hydrogen type for hardfacing of cold or hot shearer blade, liner pump casing generator
water turbine, liner dredger.
The deposited weld metal has the microstructure of martensite.
Abrasion resisting properties is good at elevated temperature, so it is used for repairing of hot tool.
Preheating is not necessary in general, but preheat at 150 and over only for high carbon steels and low
alloy steels.
Welding positions

0.40 1.28 0.46 0.025 0.010 0.35 11.2 1.40 0.01

Conditions As welded
Interpass temp. 150℃
HV 540
HRC 51.7
HS 69

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 90~110 110~150 150~200
111
Covered Electrodes
KM-900
Classifications
KS D 7035 : DFMA-250-B
JIS Z 3251 : DFMA-250-B
Description
Covering is high titania type for hardfacing of crushers, high manganese rails, buckets, bulldozer parts
and build-upof parts subject to serene impact and abrasion.
The deposited weld metal has austenite structure.
Extremely ductile deposited weld metal.
When the base metal of 13% Mn steel is hardened, cut off the hardened zone before welding.
Welding positions

0.52 0.30 12.10 0.018 0.012 0.02 2.52 0.03 0.01

As welded
Conditions Interpass temp. 150℃ Work hardenability
HV 225 510
HRC 16.9 49.8
HS 33 66.5

Dia. (mm) 3.2 4.0 5.0 6.0
Length (mm) 350 400 400 450
Amp. (A) F 90~130 140~180 190~240 220~300
112
Covered Electrodes
KM-1000 For hardfacing (Hv 800)
Classifications
KS D 7035 : DFWA-700-S
JIS Z 3251 : DFWA-700-S
Description
Hardfacing of cutter knives, shovel teeth, cutter for coal, concrete cutters and earth drills.
The deposited weld metal is harder than other kinds of deposited weld metal.
Extremely excellent heavy soil abrasion resistance.
The deposited weld metal has tungsten carbide alloy.
Machining is impossible.
Preheat at 300℃ and high over.
Postheat treat at about 600℃ immediately after welding.
Welding positions

2.98 0.60 1.88 0.022 0.014 0.04 0.02 0.01 48.0

Interpass temp. max. 350℃
HV 820
HRC 64.7
HS 90

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 90~130 120~180 170~230
113
Covered Electrodes
KQD-600
For hardfacing (High Cr&W, Hv 600)
Description
Covering is low hydrogen type for hardfacing of press mould, forged metal mould, tool steel and
hardened part by quenching.
The microstructure of deposited weld metal has martensite.
Excellent impact-resisting and wear-resisting properties at high temperature as well as room
temperature.
Welding positions

0.30 0.36 0.3 0.035 0.009 0.45 9.4 1.3 12.1

Continuous surfacing Interpass temp, max. 100℃
HV 580~620 590~610
HRC 54~56 55~56
HS 70~75 73~75

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 70~90 100~120 130~170
114
Covered Electrodes
KM-13CrM
Description
Covering is lime titania type for hardfacing of hot roller dies, tong punch and hot cutting knife, etc.
The deposited weld metal has the microstructure of a fine carbide precipitation in austenite matrix.
The high temperature hardness over 600℃ is high, so it has execllent abrasion-resistance.
Machining is possible in general.
Good bead appearance and restriking properties, preheating is not necessary in general, but preheat at
150℃ and over only for high carbon steels and low alloy steels.
Welding positions

0.30 0.48 12.4 0.016 0.014 0.02 11.8 1.5 1.8

HV 310
HRC 31
HS 43

Dia. (mm) 4.0 5.0
Length (mm) 400 400
Amp. (A) F 140~170 190~230
115
Covered Electrodes
KBH-2
Description
Hardfacing of roller and shear used at elevated temperature, ingot tongs and forged metal mould.
The deposited weld metal has the microstructure of carbide precipitation in the austenite matrix.
Preheat at about 150℃ and maintain the interpass tepmerature above 150℃ for multilayer welding of
low alloy steels and high carbon steel.
Welding positions

0.29 0.15 1.25 0.015 0.012 8.2 16.4 45.0 5.4

Continuous surfacing Interpass temp. max. 150℃
HV 250 320
HRC 22.2 32.2
HS 36 45

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 100~120 120~150 150~180
116
Covered Electrodes
KOSPEL-600H For hardfacing (Hv 600)
Description
Covering is low hydrogen type for hardfacing of metal mould, thermal cutting off machine, forging
moule, dotting punch, compression tap, impact tap and axis of rotation.
The microstructure of deposited weld metal has mertensite.
Preheat at 200~300℃ and postheat treat at 500~600℃, if possible.
Keep up interpass temperature same as preheating temperature, if possible.
Welding positions

0.25 0.59 0.95 0.018 0.013 0.02 2.5 1.0 4.2

As welded Heat treated(Air cooling)
Conditions Continuous Preheat and ℃ 550℃ X 2Hr 650℃ X 2Hr 780℃ X 2Hr
surfacing interpass temp. 150℃ 350 X 2Hr
HV 520~570 560~600 570~620 640~690 530~580 280~320
HRC 51~54 53~55 54~56 57~60 51~54 27~32
HS 67~71 71~74 71~75 77~81 67~72 40~45

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 400 400 400
Amp. (A) F 90~130 100~150 120~170 150~200
117
Covered Electrodes
KOSPEL-800R
Description
Covering is lime titania type for hardfacing of conveyor screw, caterpillar, crusher and dredger teeth.
Excellent friction and impact abrasion resisting properties.
Preheat at 200℃ and postheat treat at 500~600℃.
Welding positions

0.38 0.42 0.32 0.025 0.015 0.04 5.5 0.8 2.5

Preheat and interpass
Continuous surfacing
tem. max 300℃
HV 760~820 700~750
HRC 63~65 60~62
HS 86~90 81~85

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. (A) F 80~140 90~160 120~180 140~200
118
Covered Electrodes
KST-307-15
For stainless steel (19%Cr-9%Ni-5%Mn)
Classifications
AWS A5.4-06 : E307-15
KS D 7014 : E307-15
JIS Z 3221 : ES307-15
Description
Welding of dissimilar steel such as austenitic manganese steel to carbon steel forgings. Joining
work-hardenable steels, armour plate, austenitic manganese steels, and heat-resisting steels for
temperatures up to 350℃ and dissimilar metals. Hardfacing of hot working tools, stainless valve steels
and carbon steel items that must possess abrasion resistance in cold working.
Welding positions

0.06 0.76 4.68 0.028 0.012 9.3 18.5 0.6 0.3

Y.S (0.2%OS) T.S El.
(MPa) (MPa) (%) Remarks
AWS A5.4 min. 330 min. 590 min. 30
JIS Z3221 min. 380 min. 590 min. 25
Example 470 650 48 AW
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 55~80 80~120 100~150 140~180
(A) V·OH 45~60 70~90 90~130 -
119
Covered Electrodes
KST-308-15
For stainless steel (18%Cr-8%Ni)
Classifications
EN 1600:1997 : E 19 9 B 22 KS D 7014 : E308-15
AWS A5.4-06 : E308-15 JIS Z 3221 : ES308-15
Description
Covering is lime titania type for welding of 18%Cr-8%Ni stainless steel. (AISI 301, 302, 304, 308)
Easy welding performance without hardening brittleness because of austenitic structure of the
Good heat resistance and corrosion resistance.
Welding positions

0.06 0.38 1.54 0.025 0.016 9.6 20.5 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 35
EN 1600 min. 350 min. 550 min. 30
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 50~80 80~110 110~150 140~180
(A) V·OH 35~45 40~60 70~100 90~130 -
Approvals
CE
120
Covered Electrodes
KST-308
Classifications
EN 1600:1997 : E 19 9 R 12 KS D 7014 : E308-16
AWS A5.4-06 : E308-16 JIS Z 3221 : ES308-16
Description
Easy welding performance without hardening brittleness because of austenitic structure of the
Welding positions

0.05 0.78 1.22 0.024 0.018 9.3 19.3 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 35
EN 1600 min. 350 min. 550 min. 30
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 50~80 80~110 110~150 140~180
(A) V·OH 35~45 40~60 70~100 90~130 -
Approvals
ABS BV DNV GL KR
E308-16 UP 308 4306 RD308
Others : CWB, CE
121
Covered Electrodes
KST-308L-15
For stainless steel (Low C, 18%Cr-8%Ni)
Classifications
EN 1600:1997 : E 19 9 L B 22 KS D 7014 : E308L-15
AWS A5.4-06 : E308L-15 JIS Z 3221 : ES308L-15
Description
Excellent welding dfficicncy because of high deposition rate.
Remove water, rust, oil and all foreign matters from the groove prior to welding.
Preheating is not necessary in general.
Welding positions

0.03 0.41 1.67 0.022 0.015 9.5 20.6 0.2 0.3

AWS A5.4 min. 400 min. 520 min. 35
EN 1600 min. 320 min. 510 min. 30
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 50~80 90~130 110~150 140~180
(A) V·OH 35~45 40~60 70~90 90~130 -
Approvals
CE
122
Covered Electrodes
KST-308L
For stainless steel (Low C, 18%Cr-8%Ni)
Classifications
EN 1600:1997 : E 19 9 L R 12 KS D 7014 : E308L-16
AWS A5.4-06 : E308L-16 JIS Z 3221 : ES308L-16
Description
Excellent welding dfficicncy because of high deposition rate.
Remove water, rust, oil and all foreign matters from the groove prior to welding.
Preheating is not necessary in general.
Welding positions

0.03 0.80 0.84 0.023 0.016 9.6 19.3 0.2 0.3

AWS A5.4 min. 400 min. 520 min. 35
EN 1600 min. 320 min. 510 min. 30
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 55~80 90~130 110~150 140~180
(A) V·OH 35~45 40~60 70~90 90~130
Approvals
ABS BV GL LR
E308L-16 UP 4306 304Lm
..
Others : CWB, TUV, CE
123
Covered Electrodes
KST-308H
For stainless steel (High C, 18%Cr-8%Ni)
Classifications
EN 1600:1997 : E 19 9 H R 12 JIS Z 3221 : ES308H-16
AWS A5.4-06 : E308H-16
Description
Covering is lime titania type for welding of 18%Cr-8%Ni stainless steel and it is recommended to be use
for high temperature(about 600℃) service. (STS 304H, 307H)
Excellent creep resistance at elevated temperature.
Welding positions

0.06 0.75 0.85 0.025 0.016 9.3 19.6 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 35
EN 1600 min. 350 min. 550 min. 30
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. F 50~80 70~110 110~150 140~180
(A) V·OH 40~70 60~90 90~130 -
Approvals
CE
124
Covered Electrodes
KST-308Mo
For stainless steel (18%Cr-8%Ni-2.5%Mo)
Classifications
EN 1600:1997 : E 20 10 3 R 12 KS D 7014 : E308Mo-16
AWS A5.4-06 : E308Mo-16 JIS Z 3221 : ES308Mo-16
Description
Covering is lime titania type for butt and fillet welding of ASTM CF8M stainless steel castings.
Used for welding wrought materials such as Type 316L stainless when increased ferrite is desired.
Welds are carefully cleaned using a stainless steel wire brush.
Welding positions

0.05 0.36 1.42 0.024 0.016 9.4 19.8 2.1 0.3

AWS A5.4 min. 400 min. 550 min. 35
EN 1600 min. 400 min. 620 min. 20
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 50~80 70~110 110~150 140~180
(A) V·OH 40~70 60~90 90~130 -
Approvals
CE
125
Covered Electrodes
KST-309-15
For stainless steel (Dissimilar joint welding)
Classifications
AWS A5.4-06 : E309-15
KS D 7014 : E309-15
JIS Z 3221 : ES309-15
Description
Covering is lime titania type for welding of 22%Cr-12%Ni stainless steel and heat-resisting castings,
clad side of type 304 clad steels.
As the deposited weld metal contains ferrite in austenitic structure, its crack resistance is good.
Welding positions

0.05 0.36 1.83 0.029 0.011 13.3 24.5 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 30
JIS Z 3221 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 50~80 80~110 110~150 140~180
(A) V·OH 35~45 45~60 70~90 90~130 -
126
Covered Electrodes
KST-309
Classifications
AWS A5.4-06 : E309-16
KS D 7014 : E309-16
JIS Z 3221 : ES309-16
Description
clad side of type 304 clad steels. Welding of dissimilar steels such as Cr-Mo steel or carbon steel to
stainless steel.
As the deposited weld metal contains ferrite in austenitic structure, its crack resistance is good.
Welding positions

0.06 0.72 1.36 0.028 0.012 12.6 23.6 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 30
JIS Z 3221 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 50~80 80~110 110~150 140~180
(A) V·OH 35~45 45~60 70~90 90~130 -
Approvals
ABS BV DNV GL KR LR
E309-16 UP 309 4332 RD309 SS/CMn m
Others : CWB
127
Covered Electrodes
KST-309L-15
Classifications
EN 1600:1997 : E 23 12 L B 22 KS D 7014 : E309L-16
AWS A5.4-06 : E309L-16 JIS Z 3221 : ES309L-16
Description
stainless steel.
As its deposited weld metal has austenitic structure, with suitable ferrite, crack resistance is good and
intergranular corrosion resistance is superior to that of E309 type.
Welding positions

0.03 0.40 1.92 0.026 0.014 13.2 24.3 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 30
EN 1600 min. 320 min. 510 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 30~50 50~80 80~110 110~150 140~180
(A) V·OH 25~45 45~60 70~90 90~130 -
Approvals
CE
128
Covered Electrodes
KST-309L
Classifications
EN 1600:1997 : E 23 12 L R 12 KS D 7014 : E309L-16
AWS A5.4-06 : E309L-16 JIS Z 3221 : ES309L-16
Description
stainless steel.
As its deposited weld metal has austenitic structure, with suitable ferrite, crack resistance is good and
intergranular corrosion resistance is superior to that of E309 type.
Welding positions

0.03 0.71 1.34 0.027 0.013 12.6 23.7 0.2 0.3

AWS A5.4 min. 400 min. 520 min. 30
EN 1600 min. 320 min. 510 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 30~50 50~80 80~110 110~150 140~180
(A) V·OH 25~45 45~60 70~90 90~130
Approvals
ABS
E309L-16
Others : CWB, CE
129
Covered Electrodes
KST-309Mo-15
Classifications
AWS A5.4-06 : E309Mo-15
KS D 7014 : E309Mo-15
JIS Z 3221 : ES309Mo-15
Description
Build-up welding of Cr-Mo steel or carbon steel. Welding of AISI(SUS)316 clad steel or dissimilar steels.
Excellent crack resistance especially in the welding of dissimilar steels such as stainless steel to carbon
steel.
It is only used in the direct current condition.
Welding positions

0.06 0.35 1.84 0.027 0.012 12.4 22.2 2.4 0.3

AWS A5.4 min. 400 min. 550 min. 30
JIS Z 3221 min. 320 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 30~50 50~80 80~110 110~140 140~180
(A) V·OH 25~45 50~60 70~90 90~130 -
130
Covered Electrodes
KST-309Mo
Classifications
AWS A5.4-06 : E309Mo-16
KS D 7014 : E309Mo-16
JIS Z 3221 : ES309Mo-16
Description
Build-up welding of Cr-Mo steel or carbon steel. Welding of AISI(SUS)316 clad steel or dissimilar steels.
steel.
It is only used in the direct current condition.
Welding positions

0.06 0.35 1.84 0.027 0.012 12.4 22.2 2.4 0.3

AWS A5.4 min. 400 min. 550 min. 30
JIS Z 3221 min. 320 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 50~70 80~110 110~140 140~170
(A) V·OH 40~60 70~90 90~130 -
Approvals
DNV
309Mo
131
Covered Electrodes
KST-309LMo
Classifications
EN 1600:1997 : E 23 12 2 L R 12 KS D 7014 : E309MoL-16
AWS A5.4-06 : E309LMo-16 JIS Z 3221 : ES309LMo-16
Description
Build-up welding of AISI(SUS)316 clad steel or dissimilar steels.
steel.
Welding positions

0.03 0.76 1.78 0.026 0.013 13.1 23.2 2.4 0.3

AWS A5.4 min. 400 min. 520 min. 30
EN 1600 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 30~55 55~80 90~120 110~140 140~180
(A) V·OH 25~45 45~60 70~90 90~130 -
Approvals
KR
RD309MoL
Others : CE
132
Covered Electrodes
KST-310
Classifications
EN 1600:1997 : E 25 20 R 12 KS D 7014 : E310-16
AWS A5.4-06 : E310-16 JIS Z 3221 : ES310-16
Description
Covering is lime titania type for welding of AISI(SUS) 310S, SCS 18 and clad side of 18%Cr-8%Ni
stainless clad steel.
The deposited weld metal has perfect austenitic structure.
Good mechanical property and heat resistance of the depodited weld metal.
Welding positions

0.11 0.40 1.86 0.025 0.013 20.8 25.6 0.2 0.3

AWS A5.4 min. 400 min. 550 min. 30
EN 1600 min. 350 min. 550 min. 20
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 30~50 50~80 80~110 110~140 140~180
(A) V·OH 25~45 45~60 70~90 90~130 -
Approvals
CWB, CE
133
Covered Electrodes
KST-312
For stainless steel (Cladding or Dissimilar joint)
Classifications
EN 1600:1997 : E 29 9 R 12 KS D 7014 : E312-16
AWS A5.4-06 : E312-16 JIS Z 3221 : ES312-16
Description
Covering is lime titania type for welding of 29%Cr-9%Ni type cast steels and difficult to weld steels.
Joint welding and hardfacing of stainless steel and heat resisting steels.
Good crack resistance because of extremely much quantity of ferrite of the deposited weld metal.
Welding positions

0.08 0.45 1.30 0.028 0.012 8.5 29.1 0.2 0.3

AWS A5.4 min. 400 min. 660 min. 22
EN 1600 min. 450 min. 650 min. 15
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 40~80 70~110 110~140 140~180
(A) V·OH 35~75 70~90 80~120 -
Approvals
CE
134
Covered Electrodes
TENSILE WELD For stainless steel (Cladding or Dissimilar joint)
Description
Covering is lime titania type for welding of 29%Cr-9%Ni type cast steels and difficult to weld steels.
Joint welding and hardfacing of stainless steel and heat resisting steels.
Good crack resistance because of extremely much quantity of ferrite of the deposited weld metal.
Good usability and weldability.
Welding positions

0.08 0.95 1.48 0.032 0.015 8.6 29.8 0.2 0.3


AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 40~80 70~100 110~140 140~180
(A) V·OH 35~75 70~100 90~130 -
135
Covered Electrodes
KST-316-15
For stainless steel (18%Cr-12%Ni-Mo)
Classifications
EN 1600:1997 : E 19 12 2 B 22 KS D 7014 : E316-15
AWS A5.4-06 : E316-15 JIS Z 3221 : ES316-15
Description
Covering is lime titania type for welding of 18%Cr-12%Ni-Mo stainless steel. (AISI 316) or dissimilar
steels.
Especially suitable for flat and horizontal fillet welding.
Excellent corrosion resistance against sulphurous acid, phosphoric acid and acetic acid.
Welding positions

0.06 0.39 1.18 0.029 0.013 11.5 18.9 2.3 0.3

AWS A5.4 min. 400 min. 520 min. 30
EN 1600 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 50~70 80~120 110~140 140~170
(A) V·OH 35~45 45~60 70~90 90~130 -
Approvals
CE
136
Covered Electrodes
KST-316
Classifications
EN 1600:1997 : E 19 12 2 R 12 KS D 7014 : E316-16
AWS A5.4-06 : E316-16 JIS Z 3221 : ES316-16
Description
Covering is lime titania type for welding of 18%Cr-12%Ni-Mo stainless steel.
(AISI 316) or dissimilar steels.
Welding positions

0.06 0.73 1.18 0.028 0.012 12.5 18.3 2.3 0.3

AWS A5.4 min. 400 min. 520 min. 30
EN 1600 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 30~50 50~80 80~110 110~140 140~180
(A) V·OH 25~45 45~60 70~90 90~130 -
Approvals
ABS BV GL
E316-16 UP 4435
Others : CWB, CE
137
Covered Electrodes
KST-316L-15
For stainless steel (Low C, 18%Cr-12%Ni-Mo)
Classifications
EN 1600:1997 : E 19 12 3 L B 22 KS D 7014 : E316L-15
AWS A5.4-06 : E316L-15 JIS Z 3221 : ES316L-15
Description
Covering is lime titania type for welding of 18%Cr-12%Ni-Mo stainless stees, austenitic stainless steels
which are required and the place where heat treatment after welding is impossible.
Good Crack resistance and usability.
As low carbon welded metal can be obtained, intergranular corrosion resistance is superior to that of
E316 type.
Welding positions

0.03 0.40 1.21 0.025 0.022 11.4 19.2 2.5 0.3

AWS A5.4 min. 400 min. 490 min. 30

EN 1600 min. 320 min. 510 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 55~70 80~110 110~150 140~170
(A) V·OH 35~45 45~60 70~90 90~130 -
Approvals
CE
138
Covered Electrodes
KST-316L
Classifications
EN 1600:1997 : E 19 12 3 L R 12 KS D 7014 : E316L-16
AWS A5.4-06 : E316L-16 JIS Z 3221 : ES316L-16
Description
Covering is lime titania type for welding of 18%Cr-12%Ni-Mo stainless steel.
(AISI 316) or dissimilar steels.
Welding positions

0.03 0.72 1.08 0.028 0.013 12.5 18.4 2.5 0.3

AWS A5.4 min. 400 min. 490 min. 30
EN 1600 min. 320 min. 510 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~50 55~70 80~110 120~150 140~180
(A) V·OH 35~45 45~60 70~90 90~130 -
Approvals
ABS BV DNV GL KR LR
E316L-16 .. UP 316L 4435 RD316L 316Lm
Others : CWB, TUV, CE
139
Covered Electrodes
KST-317
Classifications
AWS A5.4-06 : E317-16
KS D 7014 : E317-16
JIS Z 3221 : ES317-16
Description
Covering is lime titania type for welding of AISI 317 or dissimilar steels such as carbon steel to stainless
steels.
Good weldability and performance.
Reduce the susceptibility of pitting.
Welding positions

0.06 0.74 1.20 0.026 0.017 12.3 18.5 3.2 0.3

AWS A5.4 min. 400 min. 550 min. 30
JIS Z 3221 min. 350 min. 550 min. 20
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~60 55~90 80~110 110~150 140~180
(A) V·OH 35~45 45~60 70~90 90~130 -
140
Covered Electrodes
KST-317L
Classifications
EN 1600:1997 : E 19 13 4 N L R12 KS D 7014 : E317L-16
AWS A5.4-06 : E317L-16 JIS Z 3221 : ES317L-16
Description
Covering is lime titania type for welding of 18%Cr-12%Ni-3%Mo which requires excellent corrosion
resistance to sulfuric acid, solutions containing these salts and much hot organic acids such as formic acid.
Good weldability and performance.
Reduce the susceptibility of pitting.
Welding positions

0.03 0.75 1.24 0.025 0.016 12.4 18.6 3.3 0.3

AWS A5.4 min. 400 min. 520 min. 30
EN 1600 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~60 55~90 80~110 110~150 140~180
(A) V·OH 35~45 45~60 70~90 90~130 -
Approvals
CE
141
Covered Electrodes
KST-318
For stainless steel (18%Cr-12%Ni-2%Mo-Nb)
Classifications
AWS A5.4-06 : E318-16
KS D 7014 : E318-16
JIS Z 3221 : ES318-16
Description
Covering is lime titania type for welding of AISI 318, 316, 316L stainless steel.
The deposited weld metal is highly resistant to pitting and general type of corrosion.
Insensitive to intergranular corrosion because of Nb.
Welding positions

0.05 0.76 1.32 0.022 0.015 11.9 18.5 2.3 0.7

AWS A5.4 min. 400 min. 520 min. 30
JIS Z 3221 min. 350 min. 550 min. 20
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~60 50~80 80~110 120~150 140~180
(A) V·OH 35~45 45~60 60~90 90~130 -
142
Covered Electrodes
KST-347
For stainless steel (18%Cr-8%Ni-Nb)
Classifications
EN 1600:1997 : E 19 9 Nb R 12 KS D 7014 : E347-16
AWS A5.4-06 : E347-16 JIS Z 3221 : ES347-16
Description
Covering is lime titania type for welding of AISI 304L, 321, 347 stainless steel and the place where heat
treatment after welding is impossible.
Excellent intergranular corrosion resistance.
Welding positions

C Si Mn P S Ni Cr Mo Nb
0.06 0.42 1.98 0.029 0.012 9.5 19.9 0.2 0.6

AWS A5.4 min. 400 min. 520 min. 30
EN 1600 min. 350 min. 550 min. 25
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~60 50~70 70~110 100~150 140~180
(A) V·OH 35~45 45~60 65~90 90~130 -
Approvals
CE
143
Covered Electrodes
KST-347L
For stainless steel (Low C, 18%Cr-8%Ni-Nb)
Classifications
KS D 7014 : E347L-16
JIS Z 3221 : ES347L-16
Description
Covering is lime titania type for welding of AISI 304L, 321, 347 stainless steel and the place where heat
treatment after welding is impossible.
Excellent intergranular corrosion resistance.
Welding positions

C Si Mn P S Ni Cr Mo Nb
0.03 0.46 1.68 0.028 0.011 9.8 19.4 0.2 0.7

JIS Z 3221 min. 350 min. 510 min. 30
AW : As-Welded

Dia. (mm) 2.0 2.6 3.2 4.0 5.0
Length (mm) 250 350 350 350 350
Amp. F 40~60 55~80 80~110 110~140 140~170
(A) V·OH 35~45 45~60 70~90 90~130 -
144
Covered Electrodes
KST-410
For stainless steel (13%Cr, Hardfacing)
Classifications
EN 1600:1997 : E 13 R 12 KS D 7014 : E410-16
AWS A5.4-06 : E410-16 JIS Z 3221 : ES410-16
Description
Covering is lime titania type for welding of 13%Cr steel and surfacing of the part where require
cavitation or corrosion resistance is required.
Excellent oxidation corrosion and abrasion resistance of the deposited weld metal.
Welding positions

0.08 0.70 0.76 0.030 0.012 0.2 12.1 0.2 0.3

AWS A5.4 min. 400 min. 450 min. 20
EN 1600 min. 250 min. 450 min. 15
Example 400 560 24 PWHT
PWHT : 750℃x1Hr.

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 60~90 80~110 110~150 150~170
(A) V·OH 45~60 70~90 90~130 -
Approvals
CE
145
Covered Electrodes
KST-430
For stainless steel (17%Cr, Hardfacing)
Classifications
EN 1600:1997 : E 17 R 12 KS D 7014 : E430-16
AWS A5.4-06 : E430-16 JIS Z 3221 : ES430-16
Description
Covering is lime titania type for welding of 17%Cr stainless steel or AISI 403, 405
Preheat at 200~300℃ and postheat treat at 700~800℃.
Welding positions

0.07 0.42 0.75 0.028 0.009 0.2 17.4 0.2 0.3

AWS A5.4 min. 400 min. 450 min. 20
EN 1600 min. 300 min. 450 min. 15
Example 380 530 27 PWHT
PWHT : 780℃x2Hr.

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 55~75 80~100 110~140 140~170
(A) V·OH 45~60 70~90 90~130 -
Approvals
CE
146
Covered Electrodes
KST-2209
For duplex stainless steel (22%Cr-9%Ni-Mo)
Classifications
EN 1600:1997 : E 22 9 3 N L R 12 JIS Z 3221 : ES2209-16
AWS A5.4-06 : E2209-16
Description
Covering is lime titania type for welding of 22%Cr-9%Ni-3%Mo duplex stainless steels, the principal
applicationsare chemical plant and shipbuilding as well as nuclear plant industries. (UNS S31803)
Excellent pitting corrosion resistance and stress corrosion cracking resistance.
Please perform welding with selecting proper heat input according to the required mechanical properties.
Welding positions

C Si Mn P S Ni Cr Mo N
0.02 0.62 0.80 0.025 0.011 9.3 21.9 3.2 0.18

AWS A5.4 min. 400 min. 690 min. 20
EN 1600 min. 450 min. 550 min. 20
AW : As-Welded

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 350
Amp. F 50~80 80~110 110~150 140~180
(A) V·OH 40~60 70~100 90~130 -
Approvals
CE
147
Covered Electrodes
KL-100
For cast iron
Classifications
KS D 7008 : DFCCI
JIS Z 3252 : DFCCI
Description
Covering is graphite type for repairing of all kind of cast iron product cavity filling.
Preheat at minimum 200℃. The temperature to be applied varies in accordance with kind, shape and
size of base metal.
Gradual cooling is recommended after welding.
Welding positions

C Si Mn P S Fe
3.16 6.27 0.42 0.015 0.006 Rem.

Hv HRC
280 27.1

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 110~140 150~190 190~220
148
Covered Electrodes
KCF-50 For cast iron
Classifications
AWS A 5.15-90 : Est
Description
Covering is graphite type for repairing of all kind of cast iron product.
Stable arc, easy slag removal aqnd beautiful bead appearance.
Preheat at minimum 200℃. The temperature to be applied varies in accordance with kind, shape and
size of base metal.
Gradual cooling is recommended after welding.
Welding positions

C Si Mn P S Fe
1.68 0.50 0.35 0.021 0.006 Rem.

T.S El. Hardness
(MPa) (%) (Hv)
490 33 200

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 350 350 400 400
Amp. (A) F 60~90 90~130 130~180 150~200
149
Covered Electrodes
KFN-50
For cast iron
Classifications
EN ISO 1071:2003 : E C NiFe-Cl 1 KS D 7008 : DFCNiFe
AWS A 5.15-90 : ENiFe-CI JIS Z 3252 : DFCNiFe
Description
Covering is graphite type for joining of spheroidal graphit cast iron or repairing of cast iron products
such as cylinder covers, motor beds, casings and gears.
Good crack resistance and mechanical properties.
Preheat at 150~300℃. The temperature to be applied varies in accordance with kind, shape and size of
base metal.
Welding positions

C Si Mn P S Ni Cu Fe Al
0.80 0.36 0.45 0.008 0.002 55.5 0.05 Rem. 0.05

T.S Hardness
(MPa) HV HB HS
550 180~210 171~200 26~30

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 550
Amp. (A) F 60~90 80~120 120~150 140~190
Approvals
CE
150
Covered Electrodes
KSN-100 For cast iron
Classifications
EN ISO 1071:2003 : E C Ni-Cl 1 KS D 7008 : DFCNi
AWS A 5.15-90 : ENi-CI JIS Z 3252 : DFCNi
Description
Covering is graphite type for repairing and joining of various kinds of cast iron products such as
cylinder covers, motor beds, casings and gears or repairing co cast iron, alloy cast iron and malleable
cast iron.
Easily machinable deposited weld metal.
Chip off base metal completely at the repairing part.
Preheat at 150~300℃. The temperature to be applied varies in accordance with kind, shape and size of
base metal.
Welding positions

C Si Mn P S Ni Cu Fe Al
0.55 0.40 0.35 0.009 0.001 Rem. 0.05 0.85 0.05

T.S Hardness
(MPa) HV HB HS
420 160~190 152~181 24~28

Dia. (mm) 2.6 3.2 4.0 5.0
Length (mm) 300 350 350 550
Amp. (A) F 60~90 70~110 110~130 130~150
Approvals
CE
151
Covered Electrodes
CUTTING ROD
For special purpose (Cutting operation)
Description
Cutting of carbon steels, cast irons, stainless steels and nonferrous alloys, etc.
Designed for high efficiency in cutting of all kinds of steel.
Excellent usability.
When the electrodes have absorbed moisture, redry the electrode at 70~80℃ for 30 minutes prior to use.
Illustration
Removal of protrusion
Removal of down gate, cross gate, etc.

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 150~130 230~180 300~400
152
Covered Electrodes
GOUGING ROD For special purpose (Gouging operation)
Description
Gouging of carbon steels, cast irons, stainless steels and nonferrous alloy, etc.
Designed for high efficiency in gouging of all kinds of steel.
Operated surface is very clean.
Suitable for rapid removal of unnecessary parts.
When the electrodes have absorbed moisture, redry the electrode at 70~80℃ for 30 minutes prior to use.
Gouging hints
In gouging operation worker must maintain 10~30°between
the electrode and base plate.
Gouging direction
3 2 1
10~30。

Dia. (mm) 3.2 4.0 5.0
Length (mm) 350 400 400
Amp. (A) F 150~180 230~260 270~320
153

Electrodos-Revestidos Kiswell

Uploaded by

Copyright:

Available Formats

Electrodos-Revestidos Kiswell

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electrodos-Revestidos Kiswell

Uploaded by

Copyright:

Available Formats

Covered Electrodes

FOR CARBON STEEL

KCL-10For 420MPa mild steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (DC +)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

K-6012For 420MPa mild steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC -)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

KR-3000V For 420MPa mild steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +, -)

K-6022For 420MPa mild steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC -)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC -)

KT-303 For 420MPa mild steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +, -)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

KH-500TFor 490MPa high tensile steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

KH-500VLF For 490MPa high tensile steel

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +, -)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +, -)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal

Sizes available and recommended currents (AC or DC +, -)

Typical chemical composition of all-weld metal (%)

Typical mechanical properties of all-weld metal