0% found this document useful (0 votes)
240 views3 pages

Structural Analysis and Design COVER

dada
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
240 views3 pages

Structural Analysis and Design COVER

dada
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

PROPOSED ONE-STOREY RESIDENTIAL BUILDING

BRGY. POLOYAGAN, PAGADIAN CITY

Design Calculations

FATIMAH AYNA M. LAO


PRC No: 138896
STRUCTURAL DESIGN CRITERIA

A. Design Codes and References


A.01 American Concrete Institute (ACI) Publication:
ACI 318-2002 Building Code Requirements for Structural Concrete
ACI 315-80 Manual of Standard Practice for Details and Detailing of Concrete
Reinforcement
A.02 American Institute of Steel Construction (AISC) Publication:
Manual of Steel Construction, 9th Edition
“Allowable Stress Design” (ASD)
A.03 American Welding Society (AWS) Publication D.1.1-2000
A.04 American Society for Testing Materials (ASTM)
A.05 National Structural Code of the Philippines (NSCP) Vol. 1, 6th edition 2010
A.06 Association of Structural Engineers of the Philippines (ASEP)
Handbook of Structural Steel Shapes and Sections, 1987
A.07 Uniform Building Code (UBC), Vol. 2 1997 Edition

B. Material Specifications
B.01 Concrete Cylinder Strength, fc’ at 28 days
Wall Footing 21.00 MPa (3000 psi)
Slab on Grade 21.00 MPa (3000 psi)
Suspended Slab 28.00 MPa (3000 psi)
Columns, Beams & Girders 28.00 MPa (3000 psi)
B.02 Reinforcing Bars, Fy
10 mm dia. & below (Grade 33) 275.00 MPa (40 ksi)
12 mm dia. & above (Grade 33) 414.00 MPa (40 ksi)
B.03 Structural Steel, ASTM A36, Fy 248.00 MPa (36 ksi)
B.04 Cold Formed Steel, ASTM 33 Grade, Fy 230.00 MPa (33 ksi)

C. Loads
C.01 Dead Load
Concrete 24.00 kN/m3
Structural Steel 77.00 kN/m3
Soil 18.00 kN/m3
Water 9.81 kN/m3
Ceiling & Insulation 0.20 kPa
Floor Finish 1.00 kPa
Roofing, Purlins and Insulation 0.20 kPa
Utilities 0.20 kPa
100 mm thick CHB 2.11 kPa
150 mm thick CHB 2.73 kPa

C.02 Live Load


Roof 0.60 kPa
Residential 1.90 kPa
Balcony 2.90 kPa
Office 2.40 kPa
Corridors Above Ground Floor 3.80 kPa
Stair / Exit Facilities 4.8 kPa

C.03 Lateral Load


C.03.1 Wind Load
Wind pressure, P for low-rise buildings based on National Structural Code of the Philippines.
P = qh[(G Cpf) – (GCpi)]
Where:
qh = velocity pressure
47.3 x 10-6 Kz KdKzt V2 Iw
G = Gust Effect factors
(Section 207.6.1)
GCpf = external pressure coefficient
(Figure 207-4)
GCpi = internal pressure coefficient
(Table 207-4)
Kz = velocity pressure exposure coefficient
(Table 207-3)
Kzt = topographic factor
1.00
V = basic wind speed
55 m/s (200 kph)
Iw = importance factor
1.00
C.03.2 Seismic Load
The total design base shear in a given direction shall be determined from the
following equations:
V = CvI W (208-4)
RT
The total Design Base shear need not exceed the following:
V = 2.5 Ca I W (208-5)
R
The total Design Base shear shall not be less than the following:
V = 0.11 Ca I W (208-6)
V = 0.8 Z Nv I W (208-7)
R
Where:
V = base shear
Ca = seismic response coefficient
(Table 208-7)
Cv = seismic response coefficient
(Table 208-8)
I = seismic importance factors
(Table 208-1)
1.0
W = total seismic dead load
R = structural system coefficient
8.5
(Table 208-11)
T = Ct (hn) 3/4
Nv = near source factor
(Table 208-5)
1.2
Na = near source factor
(Table 208-4)
1.0

D. Foundation

An allowable soil bearing capacity of 80 kPa (1670 psf) was used in the design of the foundation. Confirmation of
the actual soil bearing capacity should be done prior to the construction of the foundation.

You might also like