Scribd
Upload
129 views3 pages

Confidential: Refer To Figure Q1

This document contains a circuit diagram and instructions for an experiment involving a transistor amplifier circuit. Students are asked to: 1) Sketch the circuit diagram using simulation software. 2) Use an oscilloscope to measure and record waveform shapes and voltages at several test points. 3) Use a multimeter to measure and record voltage drops across specific components. 4) Answer questions about identifying the circuit type, how it would be affected if certain components were removed, and the purpose of a voltage regulator component in the circuit.

Uploaded by

Zhamir Zhakwan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
129 views3 pages

Confidential: Refer To Figure Q1

This document contains a circuit diagram and instructions for an experiment involving a transistor amplifier circuit. Students are asked to: 1) Sketch the circuit diagram using simulation software. 2) Use an oscilloscope to measure and record waveform shapes and voltages at several test points. 3) Use a multimeter to measure and record voltage drops across specific components. 4) Answer questions about identifying the circuit type, how it would be affected if certain components were removed, and the purpose of a voltage regulator component in the circuit.

Uploaded by

Zhamir Zhakwan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

CONFIDENTIAL BBN 10205

Q1 Refer to Figure Q1.

V1 R1 R3
56kΩ 6.8kΩ
22V
VCC
VOUT
VB

C1 Q1 VE
2N2222
Vs 10µF R2
C2
1mVrms 8.2kΩ
20µF
60Hz
0° R4
1.5kΩ

Figure Q1

(a) Sketch circuit of Figure Q1 on Multi Sim layout in Figure Q1(a).


(20 marks)

Figure Q1 (a)

2 CONFIDENTIAL
CONFIDENTIAL BBN 10205

(c) By using oscilloscope, skech the waveform at point VB, VE and VOUT and record
waveform and voltage respectively in Table Q1(c).
(30 marks)
Table Q1(c)
Point VB VE VOUT

Waveform

V/DIV : 1mV/Div V/DIV : 1mV/Div V/DIV : 50mV/Div


T/DIV : 10ms/Div T/DIV : 10ms/Div T/DIV : 10ms/Div

1.395mV x 2 1.340mV x 2 68.763mV x 2


Vp-p = 2.79mV = 2.68mV = 137.526mV
= 0.00279Vpp =0.00268Vpp = 0.137526Vpp

(d) By using multimeter, record the voltage drop at point below in Table Q1(d).

(i) Point Z

(ii) Capacitor C1 and C2

3 CONFIDENTIAL
CONFIDENTIAL BBN 10205

(iii) Resistor R4

(20 marks)

Table Q1(d)
Parameter Voltage DC(measurement)
Point Z
Capacitor C1 2.76V
Capacitor C2 2.14V
Resistor R4 2.14V

(e) Refer to Figure Q1

(i) Name the circuit of Figure Q1.

--------------------------------------------------------------------------------------------

(ii) What will happen if diode of CR1 and CR4 open?

---------------------------------------------------------------------------------------------

(iii) What is the purposed of LM7812?

The IC provides fixed 12V output voltage no matter if the input voltage is fluctuating or
changing continuously or it is higher than 12V but the input voltage should not be more
than 35V which is the maximum input voltage limit this IC is capable to handle.

(10 marks)

-END OF QUESTIONS-

4 CONFIDENTIAL

You might also like