Classification: Reference: Date:

EC05-009 NTB05-067 October 5, 2005

PROCEDURE TO COMPLETE IAVL

WHEN IDLE SPEED NEEDS TO BE REDUCED.

APPLIED VEHICLES: All 2002 – 2005 models

IF YOU CONFIRM
The idle, in Park or Neutral, is more than 25 rpm above specification (with the engine
warm), and/or
DTC P0507 (ISC SYSTEM) is stored,
NOTE:
• This incident may be the result of recent cleaning or replacement of the throttle body.
The vehicle “in-use” learned idle (IAVL) may be higher after throttle body deposits are
reduced (by cleaning or replacement).
• If DTCs other than P0507 are stored, you must correct the cause for those DTCs first.
After correcting other DTCs, if you still have a P0507 and/or an idle condition above
specification, continue with this bulletin.

ACTIONS
To reduce idle RPM, perform the following in this order until IAVL successfully completes:
1. Check engine for vacuum leaks.
2. Perform IAVL procedure.
3. For 2002 and 2003 models: Check for newer ECM reprogramming data. If it’s available,
perform reprogramming, then try IAVL again. 2004 and 2005 models: Skip this step.
4. Reduce idle speed manually:
a. Disconnect injectors one at a time until IAVL completes (see step 4 of the Service
Procedure for details),
b. Reconnect the injectors, clear DTCs, and perform final IAVL.

IMPORTANT: The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be
performing. You MUST closely follow the entire Service Procedure (starting on page 2) as it contains
information that is essential to successfully completing this repair.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/5
CLAIMS INFORMATION
Submit a Primary Failed Part (PP) line claim using the following claims coding:
DESCRIPTION PFP OP CODE SYM DIA FRT
Perform IAVL Procedure (1) DE96AA ZE 32 (2)
(1) Reference the final CONSULT-II print-out and use the indicated ECM P/N as the PFP.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.

AND IF applicable:

DESCRIPTION PFP OP CODE SYM DIA FRT

DTC P0507 (3) EJ53AA ZE 32 (4)
(3) Reference the final CONSULT-II print-out and use the indicated ECM P/N as the PFP.
(4) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.

AND IF necessary:
DESCRIPTION PFP OP CODE SYM DIA FRT
Reprogram ECM (5) DE98AA ZE 32 0.7 hrs
(5) Reference the final CONSULT-II print-out and use the indicated ECM P/N as the PFP.

AND IF necessary:

DESCRIPTION PFP OP CODE SYM DIA FRT

Manual Idle Reduce Procedure (6) EX11AA ZE 32 0.6 hrs
(injector(s) disconnected)
(6) Reference the final CONSULT-II print-out and use the indicated ECM P/N as the PFP.

SERVICE PROCEDURE

NOTE: After completing repairs in this procedure, make sure any stored DTCs are
erased.

1. Make sure there are no engine vacuum leaks. Repair any vacuum leaks that are found.
Make sure to check:
• Hoses
• Intake Manifold
• Ducting between Intake Manifold and MAFS

2/5
2. Perform Idle Air Volume Learning (IAVL) procedure as follows.
NOTE: The IAVL procedure will normally complete within 2 minutes after Procedure
Start.
A. Make sure all DTCs are cleared (erased).

B. Use CONSULT-II to confirm / perform the following Pre-Conditions:

NOTE: The IAVL procedure will self-cancel if any of the following Pre-Conditions
are not met and maintained for as long as the procedure is running.

DATA MONITOR SIGNALS (ENGINE) PRE-CONDITIONS

BATTERY VOLT [V] More than 12.9V at idle.
COOLAN TEMP/S [°C] OR [°F] Between 158 - 210°F (70 - 99°C).
P/N POSI SW [ON/OFF] ON (Transmission in either Neutral or Park).
AIR COND SIG [ON/OFF] OFF (Air conditioner/HVAC switch off).
LOAD SIGNAL [ON/OFF] OFF (Lighting switch and/or rear defogger off).
COOLING FAN [ON/OFF] OFF (Engine cooling fan motor not running).
PW/ST SIGNAL [ON/OFF] OFF (Steering wheel is straight ahead).
VHCL SPEED SE [km/h] or [mph] 0 (Vehicle speed 0 mph).
WORK SUPPORT SETTING (ENGINE)
CONSULT TARGET IDLE RPM ADJ 0 (Zero)

In addition, for vehicles with CVT:

DATA MONITOR SIGNALS (TRANSMISSION) PRE-CONDITIONS
FLUID TEMP SE Less than 0.9V .

C. Turn ignition switch “OFF” and wait at least 10 seconds.

D. Start the engine and let it idle for at least 30 seconds.

E. Using CONSULT-II, select WORK SUPPORT > IDLE AIR VOL LEARN.

F. Touch START and wait 20 seconds to 2 minutes.

• If “CMPLT” is displayed on CONSULT-II screen; go to G, next step.
• If “INCMP” is displayed within 2 minutes, or test is not finished within 2 minutes,
“Idle Air Volume Learning” was not carried out successfully; go to step H.

G. Rev up the engine two or three times, then let the engine idle. Verify the idle speed
is within specifications. Refer to the EC section of the appropriate Service Manual
for specifications. If OK, procedure ends here. If not, go to step H.

H. If IAVL did not complete and you’re sure you:

• Set all of the preconditions exactly as shown in the chart above, and
• Performed steps A through F exactly as shown above.
Go to step 3 on the next page.

3/5
NOTE: Step 3 below covers 2002 and 2003 vehicles only. For 2004 and 2005 vehicles;
skip to step 4 on the next page.
• For 2004 and 2005 model years, ECM reprogramming will not clear the vehicle “in-
use” learned IAVL. Reprogramming won’t reduce the idle speed.

3. For 2002 - 2003 vehicles; you may be able to reduce the engine idle speed by
performing ECM reprogramming. Reprogramming may clear the vehicle “in-use”
learned IAVL.
A. With the ignition ON and CONSULT-II connected to the vehicle, print your current
ECM Part Number (P/N) as follows:
START(Nissan) >> ENGINE >> ECM PART NUMBER >> COPY

B. Go to ASIST: Select CONSULT Utilities > ECM/TCM Data. Then choose Model and
Model Year of the vehicle you’re working on (see Figure 1).
Vehicle /
Model
Configuration
* Click the "Add" button
Used
350Z 2004 Space
1 File(s) selected
4 Speed A/T Models
Maxima 2003 16MB
To 23710-8Y102 VQ35 4A/T ASCD
To 23710-8Y112 VQ35 4A/T ASCD TCS To: 23710-8Y102 A34 VQ35
Altima 2002 5A/T ASCD TC8
5 Speed A/T Models

"To" Sentra 2001 To 23710-8Y002 VQ35 5A/T ASCD

Number To 23710-8Y012 VQ35 5A/T ASCD TCS
Quest 2000 M/T Models
To 23710-7Y002 VQ35 6M/T ASCD
Pathfinder

Murano

Xterra Details: Add

Replaces 23710-8Y010, -8Y011

Frontier
8MB

Remove
More More

Search by Code
(per bulletin only)
KeyPad
Show me Back Main Continue
Up Menu

This illustration is for example only, your vehicle may be different. TP030621

Figure 1

C. Select the “configuration” on the screen for the vehicle you’re working on. Then
make sure that your current ECM P/N is listed in the “Replaces 23710-XXXXX, -
XXXXX, etc” section in the lower, center “Details” panel of the ASIST screen (see
Figure 1).
• If your current ECM P/N is listed in the “Details” panel, you can perform a
reprogramming using the latest (newer) data update, then go to D on the next
page.
Click here to link to the Reprogramming Procedure for Nissan Vehicles – or refer
to Attachment A in the print copy of this bulletin.

• If your current ECM P/N is not listed in the “Details” panel, new ECM data is not
available for your vehicle, go to step 4 on the next page.
4/5
 D. After following all steps of the reprogramming procedure, perform IAVL again (back
to step 2 on page 3)
• If the IAVL procedure now completes, the incident is fixed and you’re done.
• If the IAVL procedure still does not complete, go to step 4.

4. Reduce the engine idle speed manually and perform IAVL as follows:

A. With the engine running, disconnect 1 fuel injector (engine rpm should drop, MIL
may come ON).

CAUTION: Do Not disconnect the ignition (coils or spark plugs) for this step.
Disconnecting the ignition while the engine is running may cause damage to the
catalysts.

B. With the injector(s) disconnected and the engine running, perform IAVL (step 2 on
page 3).
NOTE: Make sure all DTCs are cleared

• If “CMPLT” is displayed on CONSULT-II screen within 2 minutes; go to step 5.

• If “INCMP” is displayed, or test is not finished within 2 minutes:

a. Disconnect another injector.

b. Repeat step B above,

NOTE:
• For 4 cylinder engines up to 2 injectors can be disconnected one at a time.
• For 6 and 8 cylinder engines up to 3 injectors can be disconnected one at
a time. It is best that 3 disconnected injectors (particularly on V6 engines)
not all be on the same engine bank.

5. Final IAVL procedure.

A. Make sure all injectors are connected.

B. Use CONSULT-II to erase any DTC that may be stored and clear Self Learn.

C. Turn OFF the engine, then re-start it.

D. After the engine idle has stabilized, perform IAVL again (step 2 on page 3).

5/5