Braids, v5.1, THT v1.

1
Index Qty Description Specs Value
Resistors : All resistors use the 0204 through-hole package, but the standard 0207 package will fit slanted. I like LR0204 serie from
R4, R5, R6, R7, R8, R9, R10, R12, R13, R14, R15, R 14 Resistor, 1% 100
R51 1 Resistor, 1% 330
*R1, *R2, *R3, *R11, *R22, *R23, *R55 7 Resistor, 1% 1k
R27 1 Resistor, 1% 10k
*R50 1 Resistor, 1% 20k
R30, R31, R34, R35, R41, R42, R43, R44, R52, R53 10 Resistor, 1% 24.9k
R45, R46 2 Resistor, 1% 39k
R25, R26 2 Resistor, 1% 49.9k
*R24, *R29, *R47, *R48, R54, *R56 6 Resistor, 1% 100k
R39 1 Resistor, 1% 120k
R28, R32, R40 3 Resistor, 1% 200k
Capacitors ceramic : I used the 2.54mm pin pitch for all ceramic caps but other sizes could fit. I like the MC0805 from Multicomp/Fa
C29 1 Capacitor, ceramic >= 50V, <= 2%, C0G 47p
C21, C22 2 Capacitor, ceramic >= 50V, <= 2%, C0G 100p
C13, C14, C16, C17 4 Capacitor, ceramic >= 50V, <= 2%, C0G 1n
C1, C2, C3, C4, C5, C6, C18, C20, C23, C26, C27, C 13 Capacitor, ceramic >= 16V 100n
C8 1 Capacitor, ceramic >= 6.3V 470n
Capacitors eletrolytic
C24 1 Capacitor, electrolytic NP >= 6.3V 10u
C7, C9, C15, C33 4 Capacitor, electrolytic >= 16V 10u
C25, C30 2 Capacitor, electrolytic >= 25V 47u
Diodes
D1, D2 2 1N5817
ICs
IC1, IC2 2 SN74HC595
IC3 1 LM4040 Shunt Vref A, B or C grade 2.5V
IC4 1 MCP3204 quad 12-bit ADC
IC5 1 MCP4822 dual 12-bit DAC
IC6, IC11 2 LD1117V33 3.3V
IC7 1 MCP6004 dual op-amp R2R IO
IC8 1 LM4040 Shunt Vref A, B or C grade 10V
IC9 1 TL074 quad op-amp
IC10 1 TL072 dual op-amp
Q1, Q2, Q3, Q4, Q6, Q7 6 NPN transistor 2N3904
UC1 1 STM32F103C8T6 NEEDS TO This seller is reliable.
PTH parts, top side. The display is still the most expensive parts of the project, if anybody has an alternative, ideas are welcome : n
DISP1, DISP2 2 14 segments 2 characters L Green, comm. cathode
COLOR, FM, OUT, TIMBRE, TRIG, VOCT 6 Vertical jack connector
R19, R20, R21, R36, R37, R38 6 10k linear pot, 15mm shaft
SW1 1 Encoder, 24 steps w/ clicks, w/ switch
Headers
Single row male 1X06, 1X10, 1X8, 1X09
Single row female 1X10, 1X8, 1X09,
Female header for the blue pill (optional) 2 1x20 Aliexpress
Euro power 2x05 (Preferably shrouded) Aliexpress
Programmer
Programmer to program the STM32 board
Alternative Serial "programmer" FTDI's or CH430 could also work but I have found the CP2102 to be most
1
Package Ref. Mouser References
slanted. I like LR0204 serie from TE. All 1%.
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
0204/0207
e the MC0805 from Multicomp/Farnell. I was not able t
MC0805N470J101A2.54MM
MC0805N101J500A2.54MM
MC0805N102J500A2.54MM
MC0805B104K500A2.54MM

2mm pitch, MCNP16V106M5X11

DO41-7.6

DIP-16
TO-92 LM4040CIZ-2.5
DIP-14 Microchip MCP3204-BI/P
DIP-8 Microchip MCP4822-E/P
TO-220 Can be also replaced with LM1117
DIP-14 MCP6004-I/P
TO-92 LM4040CIZ-10.0
DIP-14
DIP-8
TO-92 (Ammo)

alternative, ideas are welcome : [email protected]