Using KODAK EKTACOLOR PRIME LORR Minilab

Chemicals

CURRENT INFORMATION SUMMARY December 2017 • CIS-220E

The processing chemicals that you use in a particular CHOOSING THE RIGHT CHEMICALS FOR YOUR
minilab system depend on the type of processor the MINILAB
system incorporates and its process cycle. This publication PRIME LORR Chemicals are designed for minilabs with the
describes the use of KODAK EKTACOLOR PRIME LORR time and temperature specifications in the following table.
chemicals for processing KODAK EKTACOLOR EDGE and See Kodak Alaris Publication Z-130, Section 3, Process
ROYAL Papers in minilabs with the standard RA minilab RA-4: Using KODAK EKTACOLOR Chemicals in Minilabs
cycle. This range of single part chemicals provides for more details.
consistent high quality results combined with convenient
solution mixing. They also provide reduced replenishment Solution/ Time Temperature °C PRIME LORR
Step (Seconds) (°F) Starting-Point
rates that minimize process effluent and packaging waste. Replenishment
Note: This publication, CIS-220E, specifically describes Rate mL/m2
the products available in Europe, the Middle East, and Developer 45 37.8 ± 0.3 80
Africa; the alternate publication, CIS-220, describes the (100.0 ± 0.5)
products available in the United States, Canada, and parts Bleach-Fix 45 30 to 36 55
(86 to 97)
of Latin America.
Stabilizer 90 30 to 37 4-Tanks 195
The product line consists of: (86 to 99) 3-Tanks 390
• KODAK EKTACOLOR PRIME SP Developer The replenishment rates are starting point
Replenisher LORR recommendations for KODAK EKTACOLOR EDGE and
• KODAK EKTACOLOR PRIME SP Bleach-Fix ROYAL Papers. If you are processing
Replenisher LORR KODAK PROFESSIONAL SUPRA ENDURA VC Digital
• KODAK EKTACOLOR PRIME Stabilizer and Paper, you may need to increase the developer
Replenisher LORR replenishment rate up to 10 percent to maintain process
control aims.
The following starters are also required for the The table below can help you determine the right choice
preparation of fresh working tank solutions: for your operation. It shows which developer to choose
• KODAK EKTACOLOR RA Developer Starter based on the developer-tank volume and the number of
• KODAK EKTACOLOR PRIME SP Bleach Fix starter 10.2 x 15.2 cm (4 x 6-inch) prints typically processed in a
day. After choosing the developer, select the bleach-fix
KODAK EKTACOLOR PRIME LORR Chemicals are and stabilizer recommended for use with that developer.
intended for customers who have an average- to During periods of low utilization, you may need to increase
high-volume operation and can benefit most from these the replenishment rate by 10 to 15 percent.
features.

© 2017 Kodak Alaris Inc.

Note: If your lab prints 8.9 x 12.7 cm (3.5 x 5-inch) prints, ORDERING EKTACOLOR PRIME LORR CHEMICALS
multiply the number of prints you make each day by 0.73
to find the equivalent number of 10.2 x 15.2 cm (4 x 6-inch) EKTACOLOR PRIME LORR Chemicals are available in
prints. Use that number to select your developer. convenient mix sizes. The catalog numbers in the following
table are for Europe, the Middle East, and Africa. The table
If you have identified EKTACOLOR PRIME SP Developer shows the product details and the number of 10.2 x 15.2 cm
Replenisher LORR (for average- to high-production (4 x 6-inch) prints that can be processed per case.
volume), use these chemicals:
• KODAK EKTACOLOR PRIME SP Developer Replacement CAT No. Makes Prints
Product
Replenisher LORR
KODAK EKTACOLOR
• KODAK EKTACOLOR PRIME Bleach-Fix Replenisher PRIME SP Developer 680 1278 4 x 10 L 32,250
LORR or KODAK EKTACOLOR PRIME SP Bleach-Fix Replenisher LORR
Replenisher LORR KODAK EKTACOLOR 528 8105
PRIME Bleach-Fix
• KODAK EKTACOLOR PRIME Stabilizer and Replenisher LORR* 680 1286 2 x 10 L
23,480
Replenisher LORR (for Russia
only)
If you have identified EKTACOLOR RA Developer
Replenisher RT / LU (for low-production volume), use the KODAK EKTACOLOR 10 x 10 L
PRIME Stabilizer and One dispenser
following chemicals: Replenisher LORR bottle.
680 1294 33,070
• KODAK EKTACOLOR Developer Replenisher RT/LU Dispense liquid
to 2 x A mark
CAT 529 2396 to prepare 10
• KODAK EKTACOLOR RA Bleach-Fix and Replenisher KODAK EKTACOLOR 1 x 1.2 L
RT/LU CAT 529 2404 Developer Starter
660 1090
one bottle will
—
make 26.7 L
• KODAK EKTACOLOR PRIME Stabilizer and fresh tank
Replenisher LORR* KODAK EKTACOLOR 660 1058 1 x 1.2 L
* Use the stabilizer at a replenishment rate of 248 mL/ PRIME SP Bleach-Fix one bottle will
680 1690 —
Starter make 24 L
m2 (4 tanks) or 495 mL/m2 (3 tanks). (for Russia fresh tank
only)
Further information and guidance on managing low
production volume conditions can be found in the
technical publication CIS-246E, “Operating Minilabs at MANAGING EMPTY CONTAINERS
low levels of utilization: C41 & RA4,” which is available at In most regions, it should be possible to participate in a
www.kodakalaris.com/go/professional. local community recycling program. Check with program
authorities to determine if these bottles are eligible for
SAFE HANDLING OF PHOTOGRAPHIC local recycling. Information on preparing
CHEMICALS KODAK photochemical containers for recycling and other
Handle all chemicals carefully. When you mix solutions, publications on waste management are available on the
wear goggles or a face shield, a protective rubber apron, Kodak Alaris website at www.kodakalaris.com/es-mx/
and protective gloves made with neoprene or nitrile rubber. about/ehs.
Clean protective clothing after use to remove any chemical
residue that can cause contamination. For more SILVER RECOVERY
information about potential health hazards and safe Publications on silver management that include
handling of specific KODAK chemicals, see the label and recommendations and descriptions of silver-recovery
the Material Safety Data Sheet (MSDS) for the chemical. options are available in the Silver Management section of
Consult the MSDS for regional contact information. the Kodak Alaris website at www.kodakalaris.com/es-mx/
MSDSs are available on the Kodak Alaris website at about/ehs.
www.kodakalaris.com/es-mx/about/ehs.

2 Using KODAK EKTACOLOR PRIME LORR Minilab Chemicals • CIS-220E

PREPARING FRESH WORKING TANK SOLUTIONS Note: The replenishment rates are starting point
Developer Fresh Tank Solution recommendations for KODAK EKTACOLOR EDGE and
ROYAL Papers. If you are processing
To ensure good performance, take special care in mixing
KODAK PROFESSIONAL SUPRA ENDURA VC Digital
the developer tank solution. You should mix the developer
Paper, you may need to increase the developer
replenisher in a separate mixing vessel from the one used
replenishment rate by 10 percent.
for bleach-fix.

Volume Replenishment Rates for EKTACOLOR PRIME LORR

Chemicals
EKTACOLOR PRIME SP 500 mL
Developer LORR, mixed Solution mL/m* x mL/ft* x mL/m2 mL/ft2
Replenisher* 127 mm 127 mm
EKTACOLOR RA Developer 45 mL PRIME SP
Starter (CAT No 6601090) 10.2 3.2 80 7.5
Developer LORR
Water 455 mL PRIME SP
6.9 2.1 54 5
Total volume 1.0 L Bleach-Fix LORR

* Mixed as directed on the product label. PRIME Stabilizer

25 7.5 195 18
LORR (4 tanks)
PRIME Stabilizer
Bleach-Fix Fresh Tank Solution LORR (3 tanks)
49 15 390 36
Be very careful to avoid contamination of the developer
with bleach-fix. *mL per linear metre or foot.

Volume NORITSU Minilabs (2900, 3100 Series)

EKTACOLOR PRIME SP Bleach Fix 950 mL 1. From the main menu screen select “F.”
LORR, mixed Replenisher*
EKTACOLOR PRIME SP 50 mL 2. Highlight “Extension.” Press <YES>.
Bleach-Fix Starter (CAT No. 3. Enter your password if required, then press <YES>.
6601058)
4. Highlight “Process Specification” or “Processor
Total volume 1.0 L
Settings” and press < YES>.
* Mixed as directed on the product label. 5. Move cursor to “Basic Replenisher Amount” or
“Standard Replenishment Amount Settings.”
Stabilizer Fresh Tank Solution
To prepare one liter of stabilizer tank solution, use mixed 6. Enter the correct replenishment rates for each
EKTACOLOR PRIME Stabilizer and Replenisher LORR with chemical (developer, bleach-fix, stabilizer). Press <
no further dilution. YES> to accept the replenishment rates. Exit, and then
return to this screen to make sure you have entered
the correct replenishment rates.
Adjusting Replenishment Rates
At the time you convert to EKTACOLOR PRIME LORR
NORITSU Minilabs (2100, 2200, 2300, 2600, 2700
Chemicals, you will need to adjust your replenishment Series)
rates to the settings given in the table below. We have
1. From the main menu screen highlight “Extension” (if
included replenishment-rate adjustment procedures for
you see “Extension 1” and “Extension 2,” highlight
several minilab models. If your equipment is not listed,
“Extension 2”). Press <YES>.
check the processor manual or contact the equipment
manufacturer for their recommendations. 2. Enter your password if required, then press <YES>.
3. Highlight “Process Specification” and press < YES>.
Important 4. Move cursor to “Basic Replenisher Amount.”
If your equipment allows you to back up printer and paper 5. Enter the correct replenishment rates for each
processor data on a floppy disc or memory card, make sure chemical (developer, bleach-fix, stabilizer). Press <
you update your backup software after adjusting the YES> to accept the replenishment rates. Exit, and then
replenishment rates. Otherwise, any future data transfer return to this screen to make sure you have entered
from your backup memory will revert to the previous the correct replenishment rates.
replenishment rates and may cause incorrect
replenishment.

Using KODAK EKTACOLOR PRIME LORR Minilab Chemicals • CIS-220E 3

 NORITSU Minilabs (1001, 1201, 1701 Series) 8. Check the volume in each graduated cylinder and
1. Press <Mode> key. compare them to the numbers that appear on this
screen. If the volumes that the replenisher pumps
2. Press <Paper> key (bottom row). deliver are different from the amounts on the screen,
3. Press <D-IN> key. adjust the replenisher pumps to obtain the correct
replenishment rates. Turn the adjustment screw on
4. Highlight the <NO> key until the “CD Basic Repl”
each pump to adjust the output—clockwise to
screen appears.
increase the volume delivered or counterclockwise to
5. Enter the new replenishment rate by using the reduce the volume.
number keys located on the bottom row.
6. Press < YES> key. FUJI SFA Series
7. Press <NO> and the next screen, BF Basic Repl, will 1. Go to the “Processor Condition Settings” screen by
appear. Enter the new bleach-fix replenishment rate. pressing <5> <2> <START/YES>.
8. Press the < YES> key. 2. Press <2>, <START/YES> to get to the
“Replenishment Rate Setting” (522) screen.
9. Press the <NO> key to go to the next screen, Stb Basic
Repl. Enter the new stabilizer replenishment rate. 3. Using the arrow keys, move the cursor to the “Repl.
Rate” column.
10. Review each screen to make sure you have entered
the correct replenishment rates. 4. Set the replenishment rates by using the number keys.
5. Move the cursor to “Enter?” and select “Yes,” and
GRETAG Master Lab press the <START/YES> key.
1. To set the developer replenishment rate, press <SET>, Depending on the standard replenishment rate setting
enter your password, press <P-Proc>, press you programmed, you may be unable to reduce your
<REPRATE>. replenishment rates to the lower amounts required for
2. Enter the correct replenishment rate for the developer. EKTACOLOR PRIME LORR Chemicals. If your processor
For GRETAG Master Labs, this will be 80 mL/m2. will not accept the low replenishment rates, change the
3. Press <ENTER>. default setting to a different standard replenishment rate.
4. To change the bleach-fix and stabilizer replenishment To change the default setting:
rates, press the following: <MAINT>, enter your
password, <P. PROC>, <LIQUID>, <CALPUMP>. 1. On the main menu, press <SORT>, <1>, <7>,
<MENU>, <7>, <7>, and <START/YES>.
5. Enter the bleach-fix <BLEACH> (55) and stabilizer
<STAB> (390 for 3 countercurrent tanks) 2. On the “Installation Date Setting” screen, change the
replenishment rates. Process Code from 4 (CP40) to 1 (CP43). Highlight
“1” with the arrow keys and press <START/YES>.
6. Measure and adjust the replenishment pump outputs
to complete the rate change. Place one graduated Then enter the lower replenishment rates.
cylinder for each replenisher on the frame of the
paper processor. Put the replenisher tubes for each
solution in the graduated cylinder.
7. Select <COMM>, <P.PROC>, <MANREPL>, <TEST>.

© 2017 Kodak Alaris Inc.

TM/MC/MR: Edge, Endura, Prime, Royal
The Kodak, Kodak Professional, Ektacolor, and Lorr Trademarks are used under license from Eastman Kodak Company.

Using KODAK EKTACOLOR PRIME LORR Minilab Chemicals

KODAK Publication No. CIS-220E
Revised 12-17

KODAK ALARIS • ROCHESTER, NY 14615