Terluran HI-10
Acrylonitrile Butadiene Styrene (ABS)
DESCRIPTION
Terluran® HI-10 is an medium flow, injection molding grade with very high resistance to impact with excellent heat distortion and suitable for
injection molding and extrusion.
FEATURES APPLICATIONS
High toughness Injection molding
Very high impact Compounding
Medium flow Appliance housings
Great mechanical strength and rigidity Lawn & garden components requiring superior toughness
High impact at sub-zero temperatures
Property, Test Condition Standard Unit Values
Rheological Properties
Melt Volume Rate 220 °C/10 kg ISO 1133 cm³/10 min 5.5
Mechanical Properties
Izod Notched Impact Strength, 23 °C ISO 180/A kJ/m² 36
Izod Notched Impact Strength, -30 °C ISO 180/A kJ/m² 14
Charpy Notched Impact Strength, 23° C ISO 179/1eA kJ/m² 35
Charpy Notched Impact Strength, -30 °C ISO 179/1eA kJ/m² 13
Charpy Unnotched, -30 °C ISO 179/1eU kJ/m² 140
Tensile Stress at Yield, 23 °C ISO 527 MPa 38
Tensile Strain at Yield, 23 °C ISO 527 % 2.8
Tensile Modulus ISO 527 MPa 1900
Nominal Strain at Break, 23 °C ISO 527 % 9
Flexural Strength, 23 °C ISO 178 MPa 56
Hardness, Ball Indentation ISO 2039-1 MPa 74
Thermal Properties
Vicat Softening Temperature VST/B/50 (50N, 50 °C/h) ISO 306 °C 90
Vicat Softening Temperature, VST/A/50 (10N, 50 °C/h) ISO 306 °C 103
Contact us:
[email protected]
www.ineos-styrolution.com Page 1 of 3
Revision Date: 2016.05.30
Terluran HI-10
Acrylonitrile Butadiene Styrene (ABS)
Property, Test Condition Standard Unit Values
Heat Deflection Temperature A; (annealed 4 h/80 °C; 1.8 MPa) ISO 75 °C 93
Heat Deflection Temperature B; (annealed 4 h/80 °C; 0.45 MPa) ISO 75 °C 97
Coefficient of Linear Thermal Expansion ISO 11359 10-6/°C 80 - 110
Thermal Conductivity DIN 52612-1 W/(m K) 0.17
Electrical Properties
Dissipation Factor (100 Hz) IEC 62631-2-1 10-4 54
Dissipation Factor (1 MHz) IEC 62631-2-1 10-4 82
Relative Permittivity (100 Hz) IEC 62631-2-1 - 2.9
Relative Permittivity (1 MHz) IEC 62631-2-1 - 2.8
Volume Resistivity IEC 62631-3-1 Ohm*m >1013
Surface Resistivity IEC 62631-3-1 Ohm >1013
Other Properties
Density ISO 1183 kg/m³ 1030
Water Absorption, Saturated at 23 °C ISO 62 % 1.03
Moisture Absorption, Equilibrium 23 °C/50% RH ISO 62 % 0.21
Yellowness Index DIN 6167 - 15
Processing
Linear Mold Shrinkage ISO 294-4 % 0.4 - 0.7
Melt Temperature Range ISO 294 °C 220 - 260
Mold Temperature Range ISO 294 °C 30 - 80
Injection Velocity ISO 294 mm/s 200
Drying Temperature - °C 80
Drying Time - h 2-4
Typical values for uncolored products
SUPPLY FORM
Contact us:
[email protected]
www.ineos-styrolution.com Page 2 of 3
Revision Date: 2016.05.30
Terluran HI-10
Acrylonitrile Butadiene Styrene (ABS)
Terluran® is delivered as spherical pellets. The bulk density of the pellets is from 0.55 to 0.65 g/cm³. Standard Packaging unit: 25 kg PE-bag
on palette, shrunk or wrapped with PE film or delivery in silo trucks. PE bags should not be stored outside. In dry areas with normal
temperature control, Terluran pellets can be stored for relatively long periods of time without any change in mechanical properties. Under poor
storage conditions, Terluran absorbs moisture, but this can be removed by drying.
PRODUCT SAFETY
No adverse effects on the health of processing personnel have been observed if the products are correctly processed and the production
areas are suitably ventilated. For styrene, acrylonitrile and 1,3-butadiene the maximum allowable workplace concentrations must be observed
according to the pertaining national regulations. In Germany, the following limit values are valid (Oct. 2002): styrene, MAK-value: 20 ml/m³ =
86 mg/m³; acrylonitrile, TRK-value: 3 ml/m³ = 7 mg/m³ and 1,3-butadiene, TRK-value: 5 ml/m³ = 11 mg/m³. According to EU directive 67/548
/EWG, Annex I and TRGS 905 (Oct. 2002), acrylonitrile and 1,3-butadiene are classified as carcinogenic, category 2 (´substances which
should be regarded as if they are carcinogenic to man´) and 1 (substances known to be carcinogenic to man), respectively. Experience has
shown that during appropriate processing of Terluran with suitable ventilation the values obtained are well below the limits mentioned above.
TRGS 402 (Germany) can be used for determining and assessing the concentrations of hazardous substances in the air within working areas.
Inhalation of gaseous degradation products, such as those which may arise on severe overheating of the material or during pumped
evacuation, must be avoided. Further information can be found in our Terluran safety data sheets.
DISCLAIMER
The above mentioned data are accurate to the best of our knowledge. They are based upon reputable labs and industry standard testing
methods. These are only typical values and actual product specification may deviate at industrial range. Therefore, no data in this technical
data sheet shall constitute a warranty or representation regarding product features, fitness of the product for a specific purpose or application
or its processability. INEOS Styrolution disclaims all liability in connection therewith. The customer himself is required to verify whether or not
the product is suitable for the further processing or application intended and whether or not the product complies with the relevant statutory
requirements. Unless explicitly and individually otherwise agreed in writing, INEOS Styrolution's sole and exclusive liability with respect to its
products is set forth in INEOS Styrolution's General Terms and Conditions for Sale.
Contact us:
[email protected]
www.ineos-styrolution.com Page 3 of 3
Revision Date: 2016.05.30
