Scribd
Upload
5K views5 pages

Read and Write Action of RAM Using IC 7489

This document describes an experiment to study the read and write functions of a RAM chip (IC 7489). The experiment uses additional ICs to generate memory addresses and control the read/write functions. The procedure involves writing data to all 16 memory locations, then reading the data back and verifying it matches what was written. Tables are included to record the address, data written, and data read for each memory location.

Uploaded by

Deepak Kumbhar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
5K views5 pages

Read and Write Action of RAM Using IC 7489

This document describes an experiment to study the read and write functions of a RAM chip (IC 7489). The experiment uses additional ICs to generate memory addresses and control the read/write functions. The procedure involves writing data to all 16 memory locations, then reading the data back and verifying it matches what was written. Tables are included to record the address, data written, and data read for each memory location.

Uploaded by

Deepak Kumbhar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Read and Write Action of RAM using IC 7489

AIM: To study and verify the read and write action of RAM using IC 7489.

OBJECTIVES:
1. To get familiar with the basic types of memory.
2. To learn and study RAM writing & reading action using IC 7489.
3. To learn and study the address generation using IC 7493.

APPARATUS: Circuit Board.

PIN DIAGRAM:
CIRCUIT DIAGRAM:
FUNCTION TABLE:

Memory Write
Function Operation
Enable Enable
Write mode (data inputs are written on to the
L L Write memory ; data outputs are compliment of the
RAM content)
Read mode (data outputs are compliment of the
L H Read
RAM content)
H L Inhibit Outputs are compliment of data input
In and
H H Out All the data outputs are high
disabled

PROCEDURE:
1. Connect the +5 V and GND i.e. power supply pins to RAM IC 7489, counter IC 7493
and the output LEDs with the help of wires.
2. Select the Memory Enable ME pin to low level i.e. logic level ‘0’ with the help of
toggle switch.
3. Connect the manual clock to the counter.
4. With the help of toggle switches apply the input data to the RAM IC 7489.
5. The inverted data outputs (active low) are connected to four common anode LED’s.
(The data outputs are connected to common anode LED’s because the outputs
produce the complement of the selected word in RAM).
6. Connect the input write enable WE to logic level ‘0’ using Toggle switch.(write
operation)
7. To write a 4 bit data into the RAM, first set the address in the counter and the inputs
in the four toggle switches connected to the four input data lines.
8. Store all 16 memory locations by applying clock pulses to the counter IC 7493.
9. Flip the toggle switch (WE) to the logic level ‘1’ i.e. read operation.
10. By applying clock pulses, check the all 16 memory locations with the help of four
output LED’s.

Important Note:
 If you switch off the power supply after storing the data into the RAM, then all
the data will get erased.
OBSERVATION TABLE:

1. Write Operation: ME=’0’ WE=’0’

Equivalent
Equivalent
Addresss Hex Data In
Hex Data
address
D C B A D4 D3 D2 D1
0 0 0 0
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
2. Read Operation: ME=’0’ WE=’1’

Equivalent
Equivalent
Addresss Hex Data In
Hex Data
address
D C B A D4 D3 D2 D1
0 0 0 0
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1

RESULT:

QUESITONS:
1. What is RAM?
2. What are differences between RAM and ROM?
3. What are the different types of RAM and ROM?

You might also like