SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF

MATERIALS 6TH EDITION GASKELL

SOLUTIONS

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS

6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.8* One mole of a monatomic ideal gas at standard temperature and

pressure (STP) undergoes the following three processes:

1. at constant Pressure the Temperature is doubled.

2. at constant Temperature the Pressure is doubled

3. the gas is returned to STP via constant volume process

Calculate U, H, q and w for each of the steps.

Solution

First calculate the values of T, V and P at the states A, B and C.

Step 1

T V P
A TA VA PA
B 2TA 2VA PA
C 2TA VA 2PA

Step 1 A B

U1  CV T  CV (2TA  TA )  CV TA
w1  PAV  PA (2VA  VA )  PAVA  RTA
q1  U  w  CV TA  RTA  (CV  R )TA

Step 2 BC
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

U 2  CV T  CV (2TA  2TA )  0
VC RTB VC dV V
w2   dV  2 RTA   2 RTA ln C  2 RTA ln(2)
VB V V B V VB
q2  w  2 RTA ln(2)

Step 3 CA

U 3  CV T  CV (TA  2TA )  CV TA

RT VA
w3   dV  0 since VC  VA
V VC

q3  U 3  CV TA

Thus we see that for the entire process:

U  CV TA  0  CV TA  0 as it should for a state function

 w  RT  2RT ln(2)  0
i A A

 q  (C  R)T  2RT ln(2)  C T

i V A A V A  RTA  2 RTA ln(2)
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.9*

M constant C
Paramagnetic salts often obey the Curie relation:  
H T T

Obtain an expression for the work needed to change the magnetization from

M  0 to M  M of such a material. Assume that the field and the magnetization are

parallel.

Solution

Mf Mf TM TM 2f H M
w 0V H  dM   0V  dM  0V  0V f f
0 0 C 2C 2

Hf M f
From the equality w  0V we see that to get to the same M at higher
2

temperature, more work is needed. Temperature works against the ordering of the

moments.

Hf M f
From the equality w  0V we also see that the work needed is the area under
2

the linear H vs. M plot.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.10 * One mole of a monatomic ideal gas is taken on the path A B 

C D A as shown in Figure 2.7 .

(1) A B is a reversible isothermal expansion of the gas;

(2) B  C is a reversible adiabatic expansion of the gas;

(3) C D is a reversible isothermal compression of the gas

(4) D  A is a reversible adiabatic compression of the gas.

a. Derive expressions for U, q and w during each step in terms of Va, Vb, Vc, Vd, t1,

t2 cV and R. Determine the sign of each.

b. Determine the values of wi), qi) and Ui) in terms of Va, Vb, Vc, Vd, t1, t2

and R. Determine the sign of each.

Figure 2.7
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Solution

Vb
(1) A  B U1  0; w1  q1  Rt2 ln( ) >0
Va
(2) B  C q2  0; U 2  cV (t 2 -t1 )  0;  w2 =U 2 so w 2 > 0
Vd
(3)C  D U 3  0; w3  q3  Rt1 ln( ) <0
Vc
(4) D  A q4  0 ; U 4  cV (t 2 -t1 ) > 0 -w4  U 4 so w 4 < 0

Vb V
SUM w i  Rt2 ln(
Va
)  Rt1 ln( d )  0
Vc
V V
q i Rt2 ln( b )  Rt1 ln( d )  0
Va Vc
U  0
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.11 *

The change in enthalpy when one mole of solid water (ice) is melted at

273 K is 6008 J.

a. Calculate the change in enthalpy when ice is melted at 298 K. Is this process

possible at 1 atm?

b. Calculate the change in enthalpy when supercooled water solidifies at 260 K.

c. Sketch the H vs. T plot for both solid and liquid water.

For this problem take the heat capacity of liquid water to be 75.44 J/k and that of solid

water to be 38 J/K over the range in temperatures of the problem. The enthalpy of

liquid water at 298 K may be set equal to zero.

Solution:

a.
273 T
H HS 2 0 (T )   cPL dT  H m   cPS dT
298 273

 75.44(273  298)  6008  38(T  273) J

 7894  38(T  273) J
T
H HL 2 0 (T )   cPLdT  75.44(T  298) J
298
Thus
H M  H L (298)  H S (298)
 0  ( 7894)  38  (298  273)
 6944 J.
Yes, ice can be superheated

b.

H fusion  H S (260)  H L (260)

H L (260)  75.44(260  298)  2866.72
H S (260)  7894  38((260  273)  8388
H fusion  ( 8388)  ( 2866.72)  5521.28 J
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

c.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.12* Three phases, β ,α and δ meet as shown in Fig. 2.8a, forming three
interphase interfaces, namely the β / α, the δ / α and the .δ / βIt can be shown that
the following holds

  /  
  /   /
sin 3 sin 2 sin 1

Using the above equation determine the equation that relates the grain boundary

grooving angle gb to the interface energy /L and the grain boundary energy .

See Fig. 2.8b.

 gb 
  /L
sin  groove sin  / L
 groove  2 / L  2
 groove  groove
sin  / L  sin(  )  sin( )
2 2
 gb   /L

sin  groove  groove
sin(
)
2
using: sin(2 X )  2sin( X ) cos( X )

sin  groove  / L  groove

 gb   2  / L cos( )
 groove 2
sin( )
2

using: sin( 2 X )  2sin( X ) cos( X )

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Solutions Manual
to accompany

Introduction to the
Thermodynamics of Materials

Sixth Edition

David R. Gaskell
School of Materials Engineering
Purdue University
West Lafayette, IN

David E. Laughlin
ALCOA Professor of Physical
Metallurgy
Carnegie Mellon University
Pittsburgh, PA
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

INTRODUCTION

This solutions manual provides worked-out answers to all problems appearing in

Introduction to the Thermodynamics of Materials, 6th Edition, with the exception of some of the
problems in Chapter 5 and Problem 9.7), which are included in the answer section in the back of
the book.

Complete solutions to all the new problems to the 6th edition are included and denoted by *.

All solutions arc comprehensive, making this supplement a useful instructional tool for
professors and students.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 1.1* The plot of V = V (P, T) for a gas is shown in Fig. 1.1. Determine.

the expressions of the two second derivatives of the volume of this plot. (note: the

principle curvatures of the surface are proportional to these second derivatives).

What are the signs of the curvatures? Explain.

Solution: start with the defining equations of T and .

 V 
   V T assuming T is constant
 P T
  2V 
 2   TV > 0
2

 P T
 V 
   V assuming  is constant
 T  P
  2V 
 2   V  0
2

 T  P

Since all terms in the expressions are positive (V, 2 and 2), both principle

curvatures are positive. The surface is convex.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 1.2* The expression for the total derivative of V with respect to the

dependent variables P and T is :

 V   V 
dV    dP    dT
 P T  T  P

Substitute the values of  and  obtained Qualitative Problem 2 into this equation

and obtain the equation of state for an ideal gas.

Solution

dV   TVdP  V dT
V 1
dV   dP  V dT
P T
dV dP dT
 
V P T
ln V  c1   ln P  c2  ln T  c3
PV  (constant)  T

The constant is nR for n moles of the ideal gas.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 1.3* The pressure temperature phase diagram (Fig. 1.4) has no two phase

areas (only two phase curves), but the temperature composition diagram of Fig. 1.5

does have two phase areas. Explain.

Solution

This must be due to the number of components in each system: The system displayed

in Fig. 1.4 is unary and that in Fig. 1.5 is a binary. We will see more on this later in

the text.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL


Problem 1.4* Calculate the value of the ratio for an ideal gas in terms of its
T

volume.

Solution

1
 T P R
  
T 1 T V
P
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.8* One mole of a monatomic ideal gas at standard temperature and

pressure (STP) undergoes the following three processes:

1. at constant Pressure the Temperature is doubled.

2. at constant Temperature the Pressure is doubled

3. the gas is returned to STP via constant volume process

Calculate U, H, q and w for each of the steps.

Solution

First calculate the values of T, V and P at the states A, B and C.

Step 1

T V P
A TA VA PA
B 2TA 2VA PA
C 2TA VA 2PA

Step 1 A B

U1  CV T  CV (2TA  TA )  CV TA
w1  PAV  PA (2VA  VA )  PAVA  RTA
q1  U  w  CV TA  RTA  (CV  R )TA

Step 2 BC
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

U 2  CV T  CV (2TA  2TA )  0
VC RTB VC dV V
w2   dV  2 RTA   2 RTA ln C  2 RTA ln(2)
VB V V B V VB
q2  w  2 RTA ln(2)

Step 3 CA

U 3  CV T  CV (TA  2TA )  CV TA

RT VA
w3   dV  0 since VC  VA
V VC

q3  U 3  CV TA

Thus we see that for the entire process:

U  CV TA  0  CV TA  0 as it should for a state function

 w  RT  2RT ln(2)  0
i A A

 q  (C  R)T  2RT ln(2)  C T

i V A A V A  RTA  2 RTA ln(2)
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.9*

M constant C
Paramagnetic salts often obey the Curie relation:  
H T T

Obtain an expression for the work needed to change the magnetization from

M  0 to M  M of such a material. Assume that the field and the magnetization are

parallel.

Solution

Mf Mf TM TM 2f H M
w 0V H  dM   0V  dM  0V  0V f f
0 0 C 2C 2

Hf M f
From the equality w  0V we see that to get to the same M at higher
2

temperature, more work is needed. Temperature works against the ordering of the

moments.

Hf M f
From the equality w  0V we also see that the work needed is the area under
2

the linear H vs. M plot.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.10 * One mole of a monatomic ideal gas is taken on the path A B 

C D A as shown in Figure 2.7 .

(1) A B is a reversible isothermal expansion of the gas;

(2) B  C is a reversible adiabatic expansion of the gas;

(3) C D is a reversible isothermal compression of the gas

(4) D  A is a reversible adiabatic compression of the gas.

a. Derive expressions for U, q and w during each step in terms of Va, Vb, Vc, Vd, t1,

t2 cV and R. Determine the sign of each.

b. Determine the values of wi), qi) and Ui) in terms of Va, Vb, Vc, Vd, t1, t2

and R. Determine the sign of each.

Figure 2.7
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Solution

Vb
(1) A  B U1  0; w1  q1  Rt2 ln( ) >0
Va
(2) B  C q2  0; U 2  cV (t 2 -t1 )  0;  w2 =U 2 so w 2 > 0
Vd
(3)C  D U 3  0; w3  q3  Rt1 ln( ) <0
Vc
(4) D  A q4  0 ; U 4  cV (t 2 -t1 ) > 0 -w4  U 4 so w 4 < 0

Vb V
SUM w i  Rt2 ln(
Va
)  Rt1 ln( d )  0
Vc
V V
q i Rt2 ln( b )  Rt1 ln( d )  0
Va Vc
U  0
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.11 *

The change in enthalpy when one mole of solid water (ice) is melted at

273 K is 6008 J.

a. Calculate the change in enthalpy when ice is melted at 298 K. Is this process

possible at 1 atm?

b. Calculate the change in enthalpy when supercooled water solidifies at 260 K.

c. Sketch the H vs. T plot for both solid and liquid water.

For this problem take the heat capacity of liquid water to be 75.44 J/k and that of solid

water to be 38 J/K over the range in temperatures of the problem. The enthalpy of

liquid water at 298 K may be set equal to zero.

Solution:

a.
273 T
H HS 2 0 (T )   cPL dT  H m   cPS dT
298 273

 75.44(273  298)  6008  38(T  273) J

 7894  38(T  273) J
T
H HL 2 0 (T )   cPLdT  75.44(T  298) J
298
Thus
H M  H L (298)  H S (298)
 0  ( 7894)  38  (298  273)
 6944 J.
Yes, ice can be superheated

b.

H fusion  H S (260)  H L (260)

H L (260)  75.44(260  298)  2866.72
H S (260)  7894  38((260  273)  8388
H fusion  ( 8388)  ( 2866.72)  5521.28 J
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

c.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 2.12* Three phases, β ,α and δ meet as shown in Fig. 2.8a, forming three
interphase interfaces, namely the β / α, the δ / α and the .δ / βIt can be shown that
the following holds

  /  
  /   /
sin 3 sin 2 sin 1

Using the above equation determine the equation that relates the grain boundary

grooving angle gb to the interface energy /L and the grain boundary energy .

See Fig. 2.8b.

 gb 
  /L
sin  groove sin  / L
 groove  2 / L  2
 groove  groove
sin  / L  sin(  )  sin( )
2 2
 gb   /L

sin  groove  groove
sin(
)
2
using: sin(2 X )  2sin( X ) cos( X )

sin  groove  / L  groove

 gb   2  / L cos( )
 groove 2
sin( )
2

using: sin( 2 X )  2sin( X ) cos( X )

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 3.7* In deriving the equation for the efficiency of a Carnot engine in Section 3.11 it

VB VC
was stated that  . Show that this equality is valid.
VA VD

Solution

Along the adibatic curve BC

PBVB  PCVC
since the gas is ideal
PBVB  RT2 and PCVC  RT1

Thus T2VB 1  TV
1 C
 1

or T21 VB  T11 VC (i)

Also, along the DA adiabatic curve

PDVD  PAVA
since the gas is ideal
PDVD  RT1 and PAVA  RT2

 1
Thus TV
1 D  T2VA 1
or T11 VD  T21 VA (ii)

T21 VB T11 VC VB VC
Dividing (i) by (ii) we obtain:  : 
T21 VA T11 VD VA VD
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 3.8* a. Calculate the change in entropy at 273 K for the freezing of water.

b. Calculate the change in entropy for the freezing of water at 260 K.

The change in enthalpy when one mole of solid water (ice) is melted at

273 K is 6008 J. Take the heat capacity of liquid water to be 75.44 J/K and that of

solid water to be 38 J/k over the range in temperatures of the problem.

Solution

The change in entropy of one mole of water on freezing at its

a. equilibrium freezing temperature is:
H L S 6008 J J
  21.23
273 273 K K

b. The freezing of water at 260 K is an irreversible process since 260 is below the

Equilibrium freezing point of water. But since entropy is a state function we

can perform a cyclic calculation as shown below:

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

S L S (260)  S S260273  S S  L (273)  S L273260  0

273 273
CPS 6008 J CPL
S L S (260)   dT    dT  0
260
T 273 K 260
T
273 6008 J 260
S L S (260)  38ln   75.44 ln 0
260 273 K 273
S L S (260)  1.85  21.23  3.68  0
J
S L S (260)  19.40
K
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 3.9* Calculate the work performed by the Carnot cycle for the shown

in Fig. 3.4 using the T-S diagram of Fg. 3.9.

Solution

The area enclosed by the box in Fig.3.9 is first calculated.

Area = (t2 – t1)S

Where S = SC – SD = SB - SA

q1
 ( S B  S A )  S
t2
q2
 ( S D  SC )  ( SC  S D )  S
t1

w  q2  q1  t2 S  t1S
w  (t2  t1 ) S , the area of the box in the T-S plot
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 4.5* We saw in Sec. 4.6 (Eq. 4.xx) that A  nkBT ln Z . We will see in the next

 A 
chapter that:    S . Perform the differentiation of A with respect to
 T V

temperature and obtain the relationship for the entropy of an isolated system in terms

of its partition function Z.

A  nk BT ln Z
 A   ln Z
    S   nk B ln Z  nk BT
 T V T
Thus
 ln Z
S  nk B ln Z  nk BT
T

Note that if we multiply both sides by T we obtain:

 ln Z
S  nk B ln Z  nk BT
T
 ln Z
TS   A  nk BT 2
T
 ln Z
Thus: U  nk BT 2
T
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Problem 4.6* A weak magnetic field is applied to a system of up and down spins. The up

spins have a slightly lower energy state than those with down spins. This is because

the up spins are favored by the weak magnetic field. Thus

  
a. Determine the partition function for this system under the influence of the weak

magnetic field.

n
b. Determine the ratio of:  for very high temperatures and very low temperatures.
n
SOLUTION

i  
a. Z   exp( )  exp( )  exp( )
k BT k BT k BT
   
exp( ) exp( )
n k BT n k BT
 and 
n     n    
exp( )  exp( ) exp( )  exp( )
k BT k BT k BT k BT
Thus:
  
exp( ) 1
n k BT n k BT
 as T gets large:   1
n 
 
n 
exp( ) 1
k BT k BT
equal numbers of up and down

 
exp( )
n k BT  
b.   exp( )
n   k BT
exp( )
k BT
The numerator of the exponental is poitive: Thus as
T gets small the exponential get large.
As T  0 n   n and n   0
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

5.13* Show that the three TdS equations can be written as:

T
1. TdS  CV dT  dV
T
2. TdS  CP dT  TV  dP
T C
3. TdS  CV dP  P dV
 V

Solution

 P 
1. TdS  CV dT  T   dV
 T V

 P 
We need to obtain an expression for  
 T V

 P   T   V 
       1
 T V  V  P  P T
 P  1 V 
    T  
 T V    V    TV  T
   
 V  P  P T


TdS  CV dT  T dV
T

 V 
2. TdS  CP dT  T   dP
 T  P
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

 V 
We need an expression for  
 T  P
 V 
We know that    V
 T  P
Thus
TdS  CP dT  TV  dP

 T   T 
3. TdS  CV   dP  CP   dV
 P V  V  P

 T   T 
We need expressions for   and  
 P V  V  P

 T  T
  = see first TdS equation above
 P V 

 T  1
  
 V  P V

Thus

T C
TdS  CV dP  P dV
 V
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

5.14* Starting from the following equation valid for a closed system, obtain

Maxwell relationships.

dH = TdS + VdP – 0VMdH

Solution

 T   V 
   
 P  S ,H  S  P ,H
 V   M 
    0V  
 H  S ,P  P  S ,H
 T   M 
    0V  
 H  S ,P  S  P ,H
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

5.15* Starting from the following equation valid for a closed system, obtain Maxwell

relationships.

dA = –SdT – PdV +0VHdM

Solution

 S   P 
   
 V T ,M  T V ,M
 S   H 
    0V  
 M T ,V  T  M ,V
 P   H 
    0V  
 M V ,T  V  M ,T
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

5.16* The cycle shown below consists of two isotherms (AB and CD) and two isobars

(BC and DA). Use the TdS equations to draw the T-S diagram for this cycle.

Use the following TdS equations

T
1. TdS  CV dT  dV
T
2. TdS  CP dT  TV  dP
T C
3. TdS  CV dP  P dV
 V

AB from 1, at constant T, ifV decreases, S decreases

BC from 3, at constant P, V increases then S increases.

From 2, at constant P if S increases T increases

C—D from 2, at constant T if P increases then S increases

D—A from 3, at constant P, if V decreases S decreases

From 2, at contant P is S decreases, T decreases.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

 T cP 1  V  1  V 
5.17* Show that:    where T    and  S   
 S cV V  P T V  P  S

Hint: use the TdS equations.

Solution

Start with the First and Second TdS equations:

T
1. TdS  CV dT  dV
T
2. TdS  CP dT  TV  dP
Set S = 0 and divide 2 by 1

T
1. CV dT   dV
T
2. CP dT  TV  dP

CP TV   dP  1 
    V T   T
CV T   dV  S V  S   S
T
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

6.11* A function Ω ≡ -F + µN, where F is the Helmholtz free energy , µ is the

chemical potential and N is the number of particles in the system.

Obtain an expression for dΩ and thus determine the independent variables for

this function.

d Ω = -dF + dN + Nd

but F ≡ U – TS so

dF = dU –TdS – SdT = -PdV –Nd - SdT

d Ω = SdT + PdV + Nd

Ω = Ω (T, V, )
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

6.12* (a) Given that the Helmholtz energy can be written as:

F   N systemk BT ln Z

Obtain simplified expressions for both F and S of an Einstein solid.

(b) Show that the entropy approaches 0 as the temperature approaches 0 in such

a solid.

From the text we saw that Z for the Einstein solid can be written as:

 
 
 1 h   1 
Z  exp - 
 2 k B T  1  exp  h 
 k T 
  B 
F = -N system k BT ln Z
3   h  
F= N system h  3N system k BT ln 1  exp  
2   k BT  
F   ln Z 
 = S  N sys k B lnZ  N syskT  
T  T V

 h 
exp   
 h   k BT  - N   h 
S  N system k B   system k B ln 1-exp   
 kT   h    k BT 
1-exp   
 k BT 
Since Nsystem = 3n

 h 
exp  
 h   k BT    h 
S  3nk B   - 3nk B ln 1-exp   
 k BT  1-exp   h    k BT 
 k T
 B 
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

 h 
exp   
 h 
S  3nk   k BT  - 3nk ln 1-exp   h 
   
 k BT  1-exp   h 
B
  k BT 
 k T
 B 
 h 
exp   
 k BT   0 as T  0
 h 
1-exp   
 k BT 
 h 
1-exp     1 as T  0: ln 1 =0
 k BT 
So S  0 as T  0
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

6.13* Obtain an expression for the internal energy of an Einstein solid as the
temperature gets very large and differentiate it with respect to T and show that the
Dulong and Petit value for the heat capacity is attained.

3 3nhv
U' nhv 
2 h
(exp( )  1)
k BT
h h
as T   exp( ) 1
k BT k BT
3 3nhv 3
U' nhv   nhv  3nk BT
2 h
( ) 2
k BT
U '
Thus CV   3nk B  3R for one mole
T
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

7.10* Three allotropes  and  of a certain element are in equilibrium at its triple
point See Figure 7.18. It is known that:
Vm  Vm and Sm  Sm
Determine which regions of the diagram are  and 
Explain your reasoning.

Solution

If the pressure is increased, equilibrium of the system favors the lowest molar volume

phase. Therefore  is in either region I or II of Fig. 7.18, since Vm  Vm . But at the

triple point, increasing the pressure moves equilibrium to the lowest molar volume

phase. Thus, region II is the  phase field.

If the temperature is increased, equilibrium of the system favors the phase of the

highest entropy. Therefore the  phase is in either region II or III since Sm  Sm But

at the triple point increasing the temperature moves equilibrium to the highest entropy

phase: therefore region III is the phase field for the  phase.

The phases are as they appear below.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

7.11*. Fig. 7.11 shows a pressure vs. temperature phase diagram for a system

exhibiting two solid state phases. Sketch the Gibbs free energy curves v. temperature

for the two solid phases and the liquid phase. Comment on the slopes of the curves.

The slopes show that the  phase has a higher entropy than the  phase both of which

have lower entropy than the liquid phase.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

7.12* Below is the Gibbs free energy vs. Pressure plot for three phases, solid (S) liquid (L)

and gas (G), near the triple point for the system. It is known that the molar volume of the

solid is greater than that of the liquid.

a. Label the three plots of G vs. P as S, L or G

b. Below, draw the T P plot for the material. Label the S, L and G fields and any other

points of interest. Note that the temperature is increasing in the downward direction.

It is important that the slope of the liquid / solid curve be as shown. His plot is the
normal P-T plot rotated by 900 clockwise!
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

7.13* The Pressure Temperature phase diagram of a certain material is shown below.
Construct the Volume Temperature diagram for this substance and label all phase
fields.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

7.14* It can be seen from Fig. 7.7 that the metastable extensions of the two phase

equilibria go into single phase fields. At the triple point it can be seen that the stable

and metastable equilibrium curves alternate as one goes around the triple point. Show

that the metastable extensions must alternate with stable two phase curves.

Solution

Assume the curves representing the stable equilibrium and those representing the

metastable equilibrium do not alternate. Demonstrate that a contradiction arises. See

below. The metastable extension of the  curve goes into the stable  phase field.

So on the extension is the  phase stable or metastable? This ambiguity shows that

the  curve can not be extended into the single  phase field. Hence the curves must

alternate.


P

T
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

8.8* Show that the truncated Kammerlingh Onnes virial equation:

PV B '(T )
 1
RT V
reduces to P(V - b’) = RT, and find the expression for b’ .

Solution 8.8

PV
 RT
 B '(T ) 
1  
 V 
1
if V  B '(T ) then using the expansion  1  x for x  1
1 x
 B '(T ) 
PV  1    P V  B '(T )  RT
 V 

so b' = B '(T )
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

8.9* Fig. 8.7 shows an isothermal variation, with pressure, of the volume of a van

der Waals gas at a temperature below its critical temperature. Redraw this Figure and

below it sketch the Helmholtz free energy vs. Volume plot. Be sure to indicate

important points on the A vs. V plot.

Solution to 8.9

dAT   PdV
 A 
    P so the slope should always be < 0
 V T
 2 A   P 
 2   and there are two extrema in P vs V.
 V T  V T
Thus there are two points where A vs. V changes its curvature.
Also the common tangent delineates the molar volumes of the
equilibrium phases.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

8.10* Obtain a simplified expression for the total derivative of the pressure for an

van der Waals’gas.

 P   P 
dP    dT    dV
 T V  V T

RT a
P  2 for a van der Waals' gas
(V  b) V

 P  R
   for a van der Waals' gas
 T V V  b
 P  RT 2a
    3 for a van der Waals' gas
 V T (V  b) V
2

R RT 2a
Thus, dP  dT  (  3 ) dV
V b (V  b) V
2

R RT
which reduces to dP = dT  2 dV if a = 0 and b = 0
V V
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

8.11* Obtain a simplified expression for the total derivative of the pressure for a gas

that obeys the truncated Kammerlingh Onnes virial equation:

PV B '(T )
 1
RT V

Solution 8.11
 B '(T )  RT
P  1  
 V  V
 P  R B '(T ) R RT  B 
     2  
 T V V V2 V  T 

 P  RT 2 B ' RT
   2 
 V T V V3
 R B '(T ) R RT  B '(T )    RT 2 B '(T ) RT 
dP     2    dT   2  dV
V  T   V 
2
V V V3

R RT
which reduces to dP = dT  2 dV if B'(T) = 0
V V
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

8.12* Derive an expression for Zcr of a van der Waals gas.

The equation of state for the van der Waals fluid is

RT a
P  2
v b v
Where P is the pressure in Pa
R is the gas constant (8.314 Joule/K)
v is the molar volume of the gas (m3)
a and b are empirical constants that vary from gas to gas.

To calculate Zcr we must obtain: Pcr, vcr and Tcr

At the critical pressure and volume, the critical isotherm has a horizontal inflection:
 P   2 P 
   2  0
 v TC  v TC

 P  RT 2a
    3 0
 v TC  v  b v
2

 2P  2 RT 6a
 v 2    4 0
TC  v  b 
3
 v
Solving we get:
8a a
v Critical  3b; RTCritical  ; Pcritical 
27b 27b2

a
3b
Pcr vcr 27b2 3
Z cr   
RTcr 8a 8
27b
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

8.13*. The ideal entropy of mixing of a binary solution is given as:

Smix   R( X A ln X A  X B ln X B )

a. Sketch the entropy of mixing vs. XB.

b. Calculate (using the expression for the ideal entropy of mixing) the ideal entropy of
mixing at B = 0.25

c. Calculate the slope of this curve at XB = 0.25

d. Calculate the partial molar entropy of component B for the composition XB = 0.25

e. Calculate the partial molar entropy of component A for the composition XB = 0.25

f. Show that your answers in d and e are consistent with your answer in c.

Solution
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Smix   R( X A ln X A  X B ln X B )
b. 4.56 J/Mol
Smix   R ln 2

Smix   R( X A ln X A  X B ln X B )
c. dSmix 9.13 J/Mol
  R[ln X B  ln X A )   R( ln 3)  R ln 3
dX B

d. S B   R(ln X B )  R ln 4 11.52 J/Mol

3
e. S A   R(ln X A )  R ln( ) 2.39 J/Mol
4

dSmix
f.  R ln 3 11.52-2.39 = 9.13 J/Mol
dX B
Smix  S B  S A  R(ln 4  ln 3  ln 4)  R ln 3
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.6* a. Calculate the values of G B and aB for an alloy of XB = 0.5 at 1000 K

assuming the solution is ideal.

M M
For ideal and regular solutions G M ( X B  0.5)  G A  G A

G M ,id ( X B  0.5)   RT S M ( X B  0.5)

1 1 1 1
 8314 * ( ln  ln )  5763J
2 2 2 2

G B  RTaB  5763J
5763
aB ( X B  0.5)  exp(  )  0.5
8314

b. Calculate the values of G B and aB for an alloy of XB = 0.5 at 1000 K that is a

regular solution with a H mixing  16,628* X A * X B .
1 1 1 1
G M ,reg (0.5)  16,626  8314 * ( ln  ln )
2 2 2 2
1 1 1 1 1
=16,626 *  8314 * ( ln  ln )
4 2 2 2 2
 1609 J

G B  RTaB  1609 J
1609
aB  exp(  )  .844
8314
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.7* A regular solution exhibits a miscibility gap. Sketch the activity of XB vs. XA at
a temperature within the miscibility gap.
Denote regions where Henry’s law is obeyed and where Raoults’ law is obeyed if
applicable.

Solution

XA
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.12* The activities of liquid iron-copper solutions at 1550 °C as a function of

composition are shown in Fig. 9.9. Sketch the activity coefficients as a function of

composition at this temperature.

Solution
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.13* Use the equation: G XS  b(T  TC ) 2  c 4 to derive the following equation

T 1/2
for  = (T): eq  (1  ) where b > 0
TC

(Hint: Use the Third Law of Thermodynamics to set  = 1 at T = 0).

Solution

G XS  b(T  TC ) 2  c 4
G XS
 0 for equilibrium

G XS
 2b(T  TC )  4c 3  0

b(T  TC )
Thus   0 and  2   are extrema
2c

By taking the second derivative  = 0 can be shown to be a maximum when T< Tc

and the other two extrema are minima when T< Tc.

b(T  TC )
2  
2c
at T = 0,   1 (by the third law)
2c T
Thus : TC  which leads to  2  (1  )
b TC
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.14* It has been found that in a certain solution the activity aA = XA over a certain

range of composition. Determine the relationship between aB = XB over the same

range of composition.

Solution

aA  X A
d (ln a A )  d (ln X A )
X Ad (ln a A )  X B d (ln a B )  0 Gibbs Duhem
XA X dX B
Thus : d (ln a2 )   d (ln a A )   A d (ln X A ) 
XB XB XB
integrating: ln a2  ln X 2  ln  where  is a constant
Thus, aB   X B   B X B
This is Henry's law.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.15* All regular solutions with positive heats of mixing have the same value of the

activity of its components (A or B) at the critical point of the miscibility gap.

a. Calculate this activity.

b. Plot aB vs. XB for a regular solution at TC for a miscibility gap.

Solution

Another way

G B  Gmix (0.5)  H mix  T Smix 

a0
=  RT  ln 2   RT ln aB
4
a
But: T  TC  0
2R
1
 ln 2  ln aB  0.1935
2
aB  0.824
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

9.16*. At a certain temperature, T the A-B system exhibits regular solution behavior.
The activity coefficient of A is given by:
ln( A )  b(1  X A )2 , where b is a constant at the given T
Compute the corresponding equation for the variation of B with composition at the
same temperature. Be sure to state justification for the steps of your solution.

Solution

ln  A  b(1  X A ) 2
Gibbs  Duhem
X Ad G A  X B d G B  0
d G A  RTd ln a A  RTd ln( A X A )
X Ad ln  A  X B d ln  B  0
XA X
d ln  B   d ln  A   A (2bX B (dX A )
XB XB
B

        
2 2
d ln B ln B bX A b (1 X B )
 1
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

10.8* A metatectic binary phase diagram displays the following invariant

transformation on cooling:

β α+L

Sketch such a phase diagram and then draw free energy curves of mixing just below,

at and just above the invariant temperature.

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

10.9* The free energy of mixing of a regular solution is given by:

Gmix  a0 X A X B  RT [ X A ln X A  X B ln X B ]
and a0  24,943 Joules/mole

a. Plot Gmix vs. XB at 1400, 1500 and 1600 K.

1400 K 1500 K 1600 K

Gmix
b. Plot vs. XB at the same
X B
temperatures as (a).

Plot of the first derivative for

1400K. The first and third zeros
are the minima of free energy
plot: they give the compositions
of the two phases in equilibrium.
The maximum in this plot and the
minimum give us the spinodals
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

Plot of the first derivative for

1500K. Only one zero for this
plot at 0.5. In fact when it passes
through zero the curve has zero
slope. This demonstrates that this
is the critical temperature.

Plot of the first derivative for

1600K.The zero value is the
minimum in free energy vs. XB
plot (0.5)

c. Determine the critical temperature for this alloy. Show work.

From the answers above we estimate TC to 1500 K.

Or, since a regular solution we calculate it to be TC = a0/2R = 1500 K
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

10.10*. A certain solid solution of A and B has a Gmix

xs
as follows:

Gmix
xs
 Gmix  Gmix
id
 X B X A[a1 X A  a2 X B ]  RT [ X A ln X A  X B ln X B ]
Where a1 = 12,500 Joules/mole and a2 = 5500 Joules/mole

a. Plot Gmix
xs
at T = 500 and 700 K

b. Sketch the T vs. XB phase diagram of this alloy

c. Determine the critical temperature and composition of this alloy.

Solution

200

0
0 0.2 0.4 0.6 0.8 1 1.2
-200

-400
Series1

-600

-800

-1000

-1200

Plot of Gmix
xs
ve. XB at 500 K, showing that a miscibility gap will exist in the T vs.
XB phase diagram with TC being less than XB = 0.5.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

500

0
0 0.2 0.4 0.6 0.8 1 1.2

-500

Series1
-1000

-1500

-2000

-2500

Plot of Gmix
xs
ve. XB at 700 K, showing that 700 K is above TC.

b. Plot will be asymmetric with TC less than XB = 0.5

 2 Gmix
xs

c. A graphical way of doing this is to plot X B2 vs. XB and see what T has the

 2 Gmix
xs

curve just touching the 0 ordinate. Below is the X B2 vs. XB for 700 K
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

10000
9000
8000
7000
6000
5000
4000
3000
2000
1000 Series1
0 Series2
-1000 0 20 40 60 80 100 120
-2000
-3000
-4000
-5000
-6000
-7000
-8000
-9000
-10000
This is above TC.

 2 Gmix
xs

The 600 K plot shows two crossings of the X B2 = 0. Hence T < TC.

10000
9000
8000
7000
6000
5000
4000
3000
2000
1000 Series1
0 Series2
-1000 0 20 40 60 80 100 120
-2000
-3000
-4000
-5000
-6000
-7000
-8000
-9000
-10000

By trying various values of T, TC can be found to be 607.5 K and the composition of

the critical point is XB = 0.35
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

10.11*. The phase diagram of an alloy that has an eutectoid transformation is shown

in Fig.10.33.

a. Sketch the Gibbs free energy curves for this alloy at T = T’.

b. Show that the  solvus must enter the  two phase field (as

shown by the arrow).

Solution
The common tangent of  and  below TE intersects the  free energy
curve to the right of E.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

10.12* A eutectoid phase diagram is shown in Fig. 10.33. Draw the phase diagram

that would result if for some reason it were impossible to form the  phase.

SOLUTION

A possible diagram is shown below. Note that the  curve is the same as the one in
Fig.10.28a until the temperature where the eutectoid temperature was. is reached. It
then is extrapolated to 0 K. The 0 K phases present are and 
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

11.11* Consider the reduction of Magnetite by CO to form pure iron:

Fe3O4 ( s)  4CO( g )  3Fe( s)  4CO2 ( g )

Calculate the partial pressure of CO and CO2 in terms of the equilibrium constant KP
for the reaction at any temperature, T.

SOLUTION

Assume the activity of the solids to be unity and that the gases behave as ideal gases.

3 4 4
aFe aCO pCO
KP  2
4
 4
2

aFe3O4 aCO pCO

1
pCO2
K P4 
pCO
Also the total pressure is 1 atmosphere:
pCO2  pCO  1

Solving the two equations simultaneously:

1
1 K P4
pCO  1
pCO2  1
( K  1)
4
P ( K P4  1)

.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

11.12* It is known that at 300 K the value of KP for a certain reaction is 1012. For the

reaction H0 is 100 kJ/mole.

a. Determine if this reaction is favorable at 800 K and estimate KP (800K). Explain.

b. The actual value of KP (800) is 35. Explain any discrepancy from your estimate.

SOLUTION

First, estimate KP at 800 K.

 K (800 K )  H 0  1 1 
ln  P    
 K P (300 K )  R  300 800 
 K (800 K )  100000  1 1 
ln  P      25.06
 P
K (300 K )  8.3144  300 800 
K (800 K )
Thus P  exp( 25.06)
K P (300 K )
K P (800 K )  K P (300 K ) exp( 25.06)  13.12

Since the value is greater than unity the reaction is possible at 800 K,

b. The above method assumed there was no temperature dependence of H0 over the

span of 500 K.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

11.13* Sketch the natural log of KP vs. 1/T for the cases of

aH0 < 0 S0 < 0

b. H0 < 0 S0 > 0

c. H0 > 0 S0 > 0

d. H0 > 0 S0 < 0

SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

15.1* 2-4 Landau Case

The excess Gibbs free energy as a function of order parameter for a solution is written

as:

G XS  Gord  Gdis  a(T  TC ) 2  C 4

where Gdis is the free energy of the disordered phase and a and C are positive constants.

a. Obtain an expression for the excess entropy of the equilibrium ordered phase as a

function of temperature.

Solution
G XS  Gord  Gdis  a (T  TC ) 2  C 4
a (T  TC ) G XS
First we obtain eq2   by setting 0
2C 
and solving for eq .
a 2 (T  TC )2
G XS  a (T  TC )eq2  Ceq4  
4C
G XS 2a 2 (T  TC )
  S XS  
T 4C
a (T  TC )
2
S XS 
2C
(valid only at T  TC )

SXS is negative since it is the excess entropy over and above the disordered entropy!
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

b. Determine the value of CP = CPord -Cpdis at the transition temperature TC.

Solution
 S 
CP  T  
 T  P
a 2 (T  TC )
Thus, since S ord  Sdis 
2C
S ord S dis a 2
 
T T 2C
S S T a2
TC ord -TC dis  C
T T 2C
2
TCa
P -C P 
Cord 0
dis

2C
2C
and since TC  : CordP -C P  a
dis

The heat capacity is of the ordered phase is larger than that of the disordered phase since

some thermal energy must be used to disorder the ordered phase on heating. See Figure

15.15.
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

15.2* 2-4-6 Landau case:

The Gibbs energy as a function of order parameter for a solution is written as:
G  a(T  TC ) 2  C 4  E 6

For this case assume C < 0 and a and E are positive.

a. Find the non-zero value of the order parameter of the solution that has the
same Gibbs Energy as that of the disordered solution.

SOLUTION

G XS of the disorderd phase  0. Thus G of the ordered phase also  0

G
If equilibrium obtains:  0. Thus we have 2 equations to solve:


G  a (T  TC ) 2  C 4  E 6  0
G
 0  2a (T  TC )  4C 3  6 E 5  a (T  TC ) 2  C 4  E 6

solving these two equations:
2a (T  TC )
on eliminating E we obtain:  0 and  2  
C
C
on eliminating a (T  TC ) we get   0 and  2  
2E
2a (T  TC ) C
Thus:   (note for part d that 4AE = C2 )
C 2E
2
C
T  TC 
4aE
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

b. Sketch the Gibbs Energy vs.  curve for the temperature in question in (a). This
temperature can be called T0.

c. Determine if the transformation for this alloy is first order. Explain.

Solution
C2
Since there are two phases at T  TC  with the same Gibbs energy and both are
4aE
minima, this is a first order transformation. This value of T can be called T0 in line with
the way we have defined T0 in the text.

d. Calculate the heat of transformation, ΔH0, for this disorder / order transformation in
terms of a, η0 and Ttr, where η0 is the order parameter at the equilibrium transition
temperatureTtr.

Solution
H  T0 S XS
S  Sordered  Sdisordered
 G XS 
 T     S T0 
XS

 T0
G XS  a (T  TC )02  C04  E06
 G XS 
  a0    S T0
2 XS

 T T0
H  T0a02  0
 C 
H  T0a    0 since C < 0)
 2E 

e. What is the significance of the sign of ΔHtr for this transformation?

It is an Exothermic transformation
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

15.3* A 2-4 Landau case:

Using the equation: G XS ( )  a(T  T0 ) 2  C 4

show that the excess enthalpy for the Landau model with B = 0 and C > 0 is:

a (T 2  TC2 )
H XS 
2 TC

Solution

TC  T T
From Eq.5.10 that eq   1
2

TC TC

2C
TC  T TC 
Inserting   a into G XS ( )  a(T  T0 ) 2  C 4
2
eq and
TC

a (TC  T ) 2
G XS  
2TC
G XS a (TC  T )
and  S XS  
T TC
a (TC  T ) 2 Ta (TC  T )
H XS  G XS  TS XS   
2TC TC
a (TC2  2TTC  T 2 ) 2aTTC  2aT 2
H XS   
2TC 2TC
a (T 2  TC2 )
H XS 
2TC

It can be seen that

dH XS aT
 CPXS 
dT TC
at TC CPXS  a
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

15.4* A solid is held at high temperature until equilibrium is attained. Its surface

displays grooves as shown in Fig. 15.19.

a. Write an expression for the relationships between the grain boundary energy of 1

and 2.

SOLUTION

See problem 2.12*

12
 gb/12  2  / 2 cos( )
1
2

b. Which grain boundary has the largest energy: 1/2 or 2/3?

SOLUTION

The one with the smallest groove angle. Hence 1/2

12
 gb/12 2  / cos( 2 )

1 2

 gb/23 2 23
 / cos( )
2 2
2

c. If ij goes to  what is the value of the grain boundary energy?

SOLUTION

ij
 gb/i  j  2  / cos( )0
i j
2

d. If ij goes to 0 what is the value of the grain boundary energy?

SOLUTION

ij
 gb/i  j  2  / cos( )  2 i / j
i j
2
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

15.5*. Small cylindrical particles has been observed to nucleate in certain alloys

system.

a. What values of r and l will minimize the energy barrier to the formation of these

particles.

b. What surface energies favor the formation of long thin cylinders? Explain

1 is the surface energy of the circular face

2 is the surface energy along the length of the cylinder.

Note: assume the volume of the particle is constant.

V=πr 2l=constant
S.E.=Surface Energy = 2πr 2 1  2 rl 2
V 2 r 2 V 2 2
S .E.  2πr 2 1   2πr 2
 1 
πr 2 πr
d ( S .E.) 2
 0  4πr 1  V 22
dr πr
r* 1 2
 for small  1 large r
l * π 1

Long rod for small 2 or large 1

Thin disc for large 2 or small 1
SOLUTIONS MANUAL FOR INTRODUCTION TO THE THERMODYNAMICS OF MATERIALS
6TH EDITION GASKELL

15.6*
Solution
G  0 for   0 (disordered)
for the ordered phase G  0  a (T  TC ) 2  E 6
a (T  TC )
or  4  
E
G
Also since in equilibrium:  0  2a (T  TC )  6 E 5

a (T  TC )
or  4  
3E
For both to be true: T0  TC

b. What is the value of the order parameter at T0?

0: that is, the phase is just beginning to order
c. Is this a first order or higher order phase transition? Explain.
Must be a higher order transition
d. Show mathematically that for T < TC, the disordered phase is unstable.

G  a (T  TC ) 2  E 6
G
 2a (T  TC )  6 E 5

 2G
 2a (T  TC )  30 E 4  2a (T  TC ) for   0
 2
 2G
Thus  2a (T  TC )  0 for T  TC
 2
Therefore unstable (a maximum)